IDT7019L20PFI [IDT]
Dual-Port SRAM, 128KX9, 20ns, CMOS, PQFP100, 14 X 14 MM, 1.40 MM HEIGHT, TQFP-100;型号: | IDT7019L20PFI |
厂家: | INTEGRATED DEVICE TECHNOLOGY |
描述: | Dual-Port SRAM, 128KX9, 20ns, CMOS, PQFP100, 14 X 14 MM, 1.40 MM HEIGHT, TQFP-100 静态存储器 内存集成电路 |
文件: | 总17页 (文件大小:140K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
HIGH-SPEED
IDT7019L
128K x 9 DUAL-PORT
STATIC RAM
Features
◆
◆
M/S = VIH for BUSY output flag on Master,
M/S = VIL for BUSY input on Slave
Interrupt Flag
True Dual-Ported memory cells which allow simultaneous
reads of the same memory location
High-speed access
◆
◆
◆
◆
◆
On-chip port arbitration logic
– Commercial:15/20ns (max.)
Low-power operation
Full on-chip hardware support of semaphore signaling
between ports
Fully asynchronous operation from either port
TTL-compatible, single 5V (±10%) power supply
Available in a 100-pin TQFP
– IDT7019L
◆
◆
◆
◆
Active:1W(typ.)
Standby: 1mW (typ.)
◆
◆
Dual chip enables allow for depth expansion without
external logic
IDT7019 easily expands data bus width to 18 bits or
more using the Master/Slave select when cascading more
than one device
Industrial temperature range (–40°C to +85°C) is available
for selected speeds
FunctionalBlockDiagram
R/WL
CE0L
CE1L
R/WR
CE0R
CE1R
OEL
OER
I/O
Control
I/O
Control
I/O0-8L
I/O0-8R
(1,2)
BUSYL
(1,2)
BUSYR
128Kx9
MEMORY
ARRAY
7019
A16L
A16R
A0R
Address
Decoder
Address
Decoder
A0L
17
17
ARBITRATION
INTERRUPT
SEMAPHORE
LOGIC
CE0L
CE0R
1L
CE
1R
CE
OEL
OER
L
R/W
R
R/W
SEML
(2)
INTL
SEMR
(2)
INT
R
M/S(1)
4840 drw 01
NOTES:
1. BUSY is an input as a Slave (M/S = VIL) and an output when it is a Master (M/S = VIH).
2. BUSY and INT are non-tri-state totem-pole outputs (push-pull).
JANUARY 2001
1
DSC-4840/2
©2000IntegratedDeviceTechnology,Inc.
IDT7019L
High-Speed 128K x 9 Dual-Port Static RAM
Industrial and Commercial Temperature Ranges
Description
The IDT7019 is a high-speed 128K x 9 Dual-Port Static RAM. The address,andI/Opinsthatpermitindependent,asynchronousaccessfor
IDT7019 is designed to be used as a stand-alone 1152K-bit Dual-Port reads or writes to any location in memory. An automatic power down
RAMorasacombinationMASTER/SLAVEDual-PortRAMfor18-bit-or- featurecontrolledbythe chipenables(CE0andCE1)permittheon-chip
more word systems. Using the IDT MASTER/SLAVE Dual-Port RAM circuitry of each port to enter a very low standby power mode.
approach in 18-bit or wider memory system applications results in full-
FabricatedusingIDT’sCMOShigh-performancetechnology,these
speed,error-freeoperationwithouttheneedforadditionaldiscretelogic. devices typicallyoperate ononly1Wofpower.
This device provides two independent ports with separate control,
TheIDT7019ispackagedina100-pinThinQuadFlatpack(TQFP).
PinConfigurations(1,2,3)
Index
100 99 98 97 96 95 94 93 92 91 90 89 88 87 86 85 84 83 82 81 80 79 78 77 76
1
NC
NC
A7L
A8L
A9L
A10L
A11L
A12L
A13L
A14L
A15L
A16L
75
74
73
72
71
70
69
68
67
66
65
64
63
62
61
60
59
58
57
56
55
54
53
52
51
NC
NC
A7R
A8R
2
3
4
5
A9R
6
A10R
A11R
A12R
A13R
A14R
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
IDT7019PF
PN100-1
(
4)
A
15R
A16R
GND
NC
NC
NC
100-Pin TQFP
Vcc
NC
NC
NC
NC
CE0L
CE1L
SEML
(
5)
Top View
NC
CE0R
CE1R
SEMR
R/WR
OER
GND
GND
NC
WL
R/
OEL
GND
NC
NC
26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50
4840 drw 02
NOTES:
1. All Vcc pins must be connected to power supply.
2. All GND pins must be connected to ground supply.
3. Package body is approximately 14mm x 14mm x 1.4mm.
4. This package code is used to reference the package diagram.
5. This text does not indicate orientation of the actual part marking.
2
IDT7019L
High-Speed 128K x 9 Dual-Port Static RAM
Industrial and Commercial Temperature Ranges
PinNames
Left Port
Right Port
Names
Chip Enables
CE0L
1L
, CE
CE0R 1R
, CE
WL
R/
WR
R/
Read/Write Enable
Output Enable
Address
OEL
A0L - A16L
OER
A0R - A16R
0L
8L
0R
8R
I/O - I/O
I/O - I/O
Data Input/Output
Semaphore Enable
Interrupt Flag
Busy Flag
SEML
INTL
SEMR
INTR
BUSYR
S
BUSYL
M/
Master or Slave Select
Power
CC
V
GND
Ground
4840 tbl 01
AbsoluteMaximumRatings(1)
RecommendedDCOperating
Conditions
Symbol
Rating
Commercial
& Industrial
Military
Unit
Symbol
Parameter
Min.
4.5
0
Typ. Max. Unit
(2)
VTERM
Terminal Voltage
with Respect
to GND
-0.5 to +7.0
-0.5 to +7.0
V
VCC
Supply Voltage
5.0
5.5
0
V
V
V
GND Ground
0
Temperature
Under Bias
-55 to +125
-65 to +150
50
-65 to +135
-65 to +150
50
oC
oC
TBIAS
TSTG
(2)
____
VIH
VIL
Input High Voltage
Input Low Voltage
2.2
6.0
Storage
Temperature
(1)
____
-0.5
0.8
V
4840 tbl 04
IOUT
DC Output Current
mA
NOTES:
1. VIL > -1.5V for pulse width less than 10ns.
2. VTERM must not exceed Vcc + 10%.
4840 tbl 02
NOTES:
1. Stresses greater than those listed under ABSOLUTE MAXIMUM RATINGS may
cause permanent damage to the device. This is a stress rating only and
functional operation of the device at these or any other conditions above those
indicated in the operational sections of this specification is not implied. Exposure
to absolute maximum rating conditions for extended periods may affect
reliability.
Capacitance
(TA = +25°C, f = 1.0MHz)
2. VTERM must not exceed Vcc + 10% for more than 25% of the cycle time or 10ns
maximum, and is limited to < 20mA for the period of VTERM > Vcc + 10%.
Symbol
Parameter(1)
Conditions(2)
VIN = 3dV
Max. Unit
CIN
Input Capacitance
9
pF
COUT Output Capacitance
VOUT = 3dV
10
pF
MaximumOperatingTemperature
andSupplyVoltage(1)
Ambient
4840 tbl 05
NOTES:
1. This parameter is determined by device characterization but is not production
tested.
2. 3dV represents the interpolated capacitance when the input and output signals
switch from 0V to 3V or from 3V to 0V.
Grade
Temperature(2)
-55OC to +125OC
0OC to +70OC
GND
Vcc
Military
0V
5.0V + 10%
5.0V + 10%
5.0V + 10%
Commercial
Industrial
0V
-40OC to +85OC
0V
4840 tbl 03
NOTES:
1. Industrial Temperature: for specific speeds, packages and powers contact your
sales office.
2. This is the parameter TA. This is the "instant on" case temperature.
3
6.42
IDT7019L
High-Speed 128K x 9 Dual-Port Static RAM
Industrial and Commercial Temperature Ranges
Truth Table I: Chip Enable(1,2)
1
CE
CE
CE0
Mode
VIL
VIH
Port Selected (TTL Active)
L
< 0.2V
VIH
>VCC -0.2V
X
Port Selected (CMOS Active)
Port Deselected (TTL Inactive)
Port Deselected (TTL Inactive)
Port Deselected (CMOS Inactive)
Port Deselected (CMOS Inactive)
X
VIL
H
>VCC -0.2V
X
X
<0.2V
4840 tbl 06
NOTES:
1. Chip Enable references are shown above with the actual CE0 and CE1 levels, CE is a reference only.
2. 'H' = VIH and 'L' = VIL.
3. CMOS standby requires 'X' to be either < 0.2V or > VCC - 0.2V.
Truth Table II: Non-Contention Read/Write Control
Inputs(1)
Outputs
CE(2)
H
OE
SEM
H
R/W
X
I/O0-8
Mode
X
X
L
High-Z
DATAIN
Deselected: Power-Down
Write to memory
L
L
H
L
H
H
DATAOUT Read memory
High-Z Outputs Disabled
X
X
H
X
4840 drw 07
NOTES:
1. A0L – A16L ≠ A0R – A16R.
2. Refer to Chip Enable Truth Table.
Truth Table III: Semaphore Read/Write Control(1)
Inputs
Outputs
(2)
R/W
I/O0-8
Mode
CE
OE
SEM
H
H
L
L
DATAOUT Read Semaphore Flag Data Out
↑
IN
0
H
L
X
X
L
L
DATA
Write I/O into Semaphore Flag
______
X
Not Allowed
4840 tbl 08
NOTES:
1. There are eight semaphore flags written to via I/O0 and read from all the I/Os (I/O0-I/O8). These eight semaphore flags are addressed by A0-A2.
2. Refer to Chip Enable Truth Table.
4
IDT7019L
High-Speed 128K x 9 Dual-Port Static RAM
Industrial and Commercial Temperature Ranges
DC Electrical Characteristics Over the Operating
Temperature and Supply Voltage Range(2) (VCC = 5.0V ± 10%)
7019L
Symbol
|ILI|
Parameter
Test Conditions
Min.
Max.
5
Unit
µA
µA
V
(1)
___
Input Leakage Current
VCC = 5.5V, VIN = 0V to VCC
CE = VIH, VOUT = 0V to VCC
IOL = 4mA
___
___
|ILO|
Output Leakage Current
Output Low Voltage
Output High Voltage
5
VOL
0.4
___
VOH
IOH = -4mA
2.4
V
4840 tbl 09
NOTES:
1. At Vcc < 2.0V, input leakages are undefined.
2. Refer to Chip Enable Truth Table.
DC Electrical Characteristics Over the Operating
Temperature and Supply Voltage Range(1,6,7) (VCC = 5.0V ± 10%)
7019L15
7019L20
Com'l Only
Com'l Only
Symbol
Parameter
Test Condition
Version
COM'L
Typ.(1) Max
Typ.(1) Max
Unit
mA
ICC
Dynamic Operating
Current
(Both Ports Active)
L
L
L
L
L
L
L
L
220
340
200
300
CE = VIL, Outputs Disabled
SEM = VIH
(2)
____
____
____
____
IND
f = fMAX
mA
mA
mA
ISB1
ISB2
ISB3
Standby Current
(Both Ports - TTL Level
Inputs)
COM'L
IND
65
100
50
75
CEL = CER = VIH
SEMR = SEML = VIH
(2)
____
____
____
____
f = fMAX
(4)
Standby Current
(One Port - TTL Level
Inputs)
COM'L
IND
145
225
130
195
CE"A" = VIL and CE"B" = VIH
Active Port Outputs Disabled,
(2)
____
____
____
____
f=fMAX , SEMR = SEML = VIH
Full Standby Current
(Both Ports - All CMOS
Level Inputs)
Both Ports CEL and
COM'L
IND
0.2
3.0
0.2
3.0
CER > VCC - 0.2V, VIN > VCC - 0.2V
or VIN < 0.2V, f = 0(3)
____
____
____
____
SEMR = SEML > VCC - 0.2V
mA
ISB4
Full Standby Current
(One Port - All CMOS
Level Inputs)
COM'L
IND
L
L
135
220
120
190
CE"A" < 0.2V and
(4)
CE"B" > VCC - 0.2V ,
SEMR = SEML > VCC - 0.2V,
____
____
____
____
VIN > VCC - 0.2V or VIN < 0.2V,
(2)
Active Port Outputs Disabled, f = fMAX
4840 tbl 10
NOTES:
1. VCC = 5V, TA = +25°C, and are not production tested. ICCDC = 120mA (Typ.)
2. At f = fMAX, address and control lines (except Output Enable) are cycling at the maximum frequency read cycle of 1/ tRC, and using “AC Test Conditions” of input
levels of GND to 3V.
3. f = 0 means no address or control lines change.
4. Port "A" may be either left or right port. Port "B" is the opposite from port "A".
5. Refer to Chip Enable Truth Table.
6. Industrial Temperature: for specific speeds, packages and powers contact your sales office.
5
6.42
IDT7019L
High-Speed 128K x 9 Dual-Port Static RAM
Industrial and Commercial Temperature Ranges
5V 5V
AC Test Conditions
Input Pulse Levels
GND to 3.0V
893Ω
Ω
893
Input Rise/Fall Times
Input Timing Reference Levels
Output Reference Levels
Output Load
3ns Max.
1.5V
DATAOUT
BUSY
INT
DATAOUT
1.5V
30pF
5pF*
347
Ω
347
Ω
Figures 1 and 2
4840 tbl 11
4840 drw 03
4840 drw 04
Figure 1. AC Output Test Load
Figure 2. Output Test Load
(for tLZ, tHZ, tWZ, tOW)
* Including scope and jig.
Waveform of Read Cycles(5)
tRC
ADDR
(4)
tAA
(4)
tACE
CE(6)
(4)
tAOE
OE
R/W
(1)
tOH
tLZ
VALID DATA(4)
DATAOUT
(2)
tHZ
BUSYOUT
(3,4)
4840 drw 05
tBDD
Timing of Power-Up Power-Down
CE(6)
tPU
tPD
ICC
50%
50%
ISB
.
4840 drw 06
NOTES:
1. Timing depends on which signal is asserted last, OE or CE.
2. Timing depends on which signal is de-asserted first CE or OE.
3. tBDD delay is required only in cases where the opposite port is completing a write operation to the same address location. For simultaneous read operations BUSY
has no relation to valid output data.
4. Start of valid data depends on which timing becomes effective last tAOE, tACE, tAA or tBDD.
5. SEM = VIH.
6. Refer to Chip Enable Truth Table.
6
IDT7019L
High-Speed 128K x 9 Dual-Port Static RAM
Industrial and Commercial Temperature Ranges
AC Electrical Characteristics Over the
OperatingTemperatureandSupplyVoltageRange(5)
7019L15
Com'l Only
7019L20
Com'l Only
Symbol
Parameter
Min.
Max.
Min.
Max.
Unit
READ CYCLE
____
____
tRC
Read Cycle Time
15
20
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
____
____
tAA
tACE
tAOE
tOH
tLZ
Address Access Time
15
15
20
20
Chip Enable Access Time(4)
Output Enable Access Time
Output Hold from Address Change
Output Low-Z Time(1,2)
____
____
____
____
10
12
____
____
3
3
____
____
3
3
Output High-Z Time(1,2)
10
10
____
____
tHZ
tPU
tPD
tSOP
tSAA
Chip Enable to Power Up Time(2)
Chip Disable to Power Down Time(2)
0
0
____
____
____
____
15
20
____
____
Semaphore Flag Update Pulse (OE or SEM)
10
10
____
____
Semaphore Address Access Time
15
20
ns
4840 tbl 12
AC Electrical Characteristics Over the
OperatingTemperatureandSupplyVoltage(5)
7019L15
Com'l Only
7019L20
Com'l Only
Symbol
Parameter
Min.
Max.
Min.
Max.
Unit
WRITE CYCLE
____
____
____
____
____
____
____
____
____
____
____
____
____
____
tWC
tEW
tAW
tAS
Write Cycle Time
15
12
12
0
20
15
15
0
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
Chip Enable to End-of-Write(3)
Address Valid to End-of-Write
Address Set-up Time(3)
Write Pulse Width
tWP
12
0
15
0
tWR
Write Recovery Time
Data Valid to End-of-Write
Output High-Z Time(1,2)
Data Hold Time(4)
tDW
tHZ
10
15
____
____
10
10
____
____
tDH
0
0
(1,2)
____
____
tWZ
Write Enable to Output in High-Z
Output Active from End-of-Write(1,2,4)
SEM Flag Write to Read Time
SEM Flag Contention Window
10
10
____
____
tOW
tSWRD
tSPS
NOTES:
0
5
5
0
5
5
____
____
____
____
ns
4840 tbl 13
1. Transition is measured 0mV from Low or High-impedance voltage with Output Test Load (Figure 2).
2. This parameter is guaranted by device characterization, but is not production tested.
3. To access RAM, CE= VIL and SEM = VIH. To access semaphore, CE = VIH and SEM = VIL. Either condition must be valid for the entire tEW time.
4. The specification for tDH must be met by the device supplying write data to the RAM under all operating conditions. Although tDH and tOW values will vary over voltage
and temperature, the actual tDH will always be smaller than the actual tOW.
5. Industrial Temperature: for specific speeds, packages and powers contact your sales office.
7
6.42
IDT7019L
High-Speed 128K x 9 Dual-Port Static RAM
Industrial and Commercial Temperature Ranges
Timing Waveform of Write Cycle No. 1, R/W Controlled Timing(1,5,8)
tWC
ADDRESS
(7)
tHZ
OE
tAW
CE or SEM(9,10)
(3)
(2)
(6)
tWP
tWR
tAS
W
R/
(7)
tWZ
tOW
(4)
(4)
DATAOUT
DATAIN
tDW
tDH
4840 drw 07
Timing Waveform of Write Cycle No. 2, CE Controlled Timing(1,5)
tWC
ADDRESS
tAW
(9,10)
or
CE SEM
(3)
(6)
(2)
tWR
tEW
tAS
R/
W
tDW
tDH
DATAIN
4840 drw 08
NOTES:
1. R/W or CE = VIH during all address transitions.
2. A write occurs during the overlap (tEW or tWP) of a CE = VIL and a R/W = VIL for memory array writing cycle.
3. tWR is measured from the earlier of CE or R/W (or SEM or R/W) going HIGH to the end of write cycle.
4. During this period, the I/O pins are in the output state and input signals must not be applied.
5. If the CE or SEM = VIL transition occurs simultaneously with or after the R/W = VIL transition, the outputs remain in the High-impedance state.
6. Timing depends on which enable signal is asserted last, CE or R/W.
7. This parameter is guaranteed by device characterization, but is not production tested. Transition is measured 0mV from steady state with the Output Test Load (Figure
2).
8. If OE = VIL during R/W controlled write cycle, the write pulse width must be the larger of tWP or (tWZ + tDW) to allow the I/O drivers to turn off and data to be
placed on the bus for the required tDW. If OE = VIH during an R/W controlled write cycle, this requirement does not apply and the write pulse can be as short as the
specified tWP.
9. To access RAM, CE = VIL and SEM = VIH. To access semaphore, CE = VIH and SEM = VIL. tEW must be met for either condition.
10. Refer to Chip Enable Truth Table.
8
IDT7019L
High-Speed 128K x 9 Dual-Port Static RAM
Industrial and Commercial Temperature Ranges
Timing Waveform of Semaphore Read after Write Timing, Either Side(1)
tSAA
tOH
A0-A2
VALID ADDRESS
VALID ADDRESS
tACE
tAW
tWR
tEW
SEM
tSOP
tDW
DATAIN VALID
DATAOUT
VALID(2)
DATA0
tAS
tWP
tDH
R/W
tSWRD
tAOE
OE
tSOP
Write Cycle
Read Cycle
4840 drw 09
NOTES:
1. CE = VIH for the duration of the above timing (both write and read cycle) (Refer to Chip Enable Truth Table).
2. "DATAOUT VALID" represents all I/O's (I/O0 - I/O8) equal to the semaphore value.
Timing Waveform of Semaphore Write Contention(1,3,4)
A0"A"-A2"A"
MATCH
(2)
SIDE "A"
R/W"A"
SEM"A"
SPS
t
A0"B"-A2"B"
MATCH
(2)
SIDE
"B"
R/W
"B"
SEM"B"
4840 drw 10
NOTES:
1. DOR = DOL = VIL, CEL = CER = VIH (Refer to Chip Enable Truth Table).
2. All timing is the same for left and right ports. Port "A" may be either left or right port. "B" is the opposite from port "A".
3. This parameter is measured from R/W"A" or SEM"A" going HIGH to R/W"B" or SEM"B" going HIGH.
4. If tSPS is not satisfied, the semaphore will fall positively to one side or the other, but there is no guarantee which side will obtain the flag.
9
6.42
IDT7019L
High-Speed 128K x 9 Dual-Port Static RAM
Industrial and Commercial Temperature Ranges
AC Electrical Characteristics Over the
OperatingTemperatureandSupplyVoltageRange(6)
7019L15
Com'l Only
7019L20
Com'l Only
Symbol
BUSY TIMING (M/S=V )
Parameter
Min.
Max.
Min.
Max.
Unit
IH
____
____
____
____
____
____
____
____
tBAA
tBDA
tBAC
tBDC
tAPS
tBDD
tWH
15
15
15
20
20
20
ns
ns
ns
ns
ns
ns
ns
BUSY Access Time from Address Match
BUSY Disable Time from Address Not Matched
BUSY Access Time from Chip Enable Low
BUSY Access Time from Chip Enable High
Arbitration Priority Set-up Time(2)
15
17
____
____
5
5
____
____
BUSY Disable to Valid Data(3)
15
17
(5)
____
____
Write Hold After BUSY
12
15
BUSY
tWB
S
TIMING (M/ =VIL)
Input to Write(4)
____
____
____
____
0
0
ns
ns
BUSY
Write Hold After BUSY
(5)
tWH
12
15
PORT-TO-PORT DELAY TIMING
tWDD
tDDD
(1)
____
____
____
____
Write Pulse to Data Delay
30
25
45
30
ns
Write Data Valid to Read Data Delay(1)
ns
4840 tbl 14
NOTES:
1. Port-to-port delay through RAM cells from writing port to reading port, refer to "Timing Waveform of Write with Port-to-Port Read and BUSY (M/S = VIH)".
2. To ensure that the earlier of the two ports wins.
3. tBDD is a calculated parameter and is the greater of 0, tWDD – tWP (actual) or tDDD – tDW (actual).
4. To ensure that the write cycle is inhibited on port "B" during contention on port "A".
5. To ensure that a write cycle is completed on port "B" after contention on port "A".
6. Industrial Temperature: for specific speeds, packages and powers contact your sales office.
10
IDT7019L
High-Speed 128K x 9 Dual-Port Static RAM
Industrial and Commercial Temperature Ranges
TimingWaveformof WritewithPort-to-PortReadand BUSY(M/S = VIH)(2,4,5)
tWC
ADDR"A"
MATCH
tWP
R/
W"A"
tDH
tDW
DATAIN "A"
VALID
(1)
tAPS
ADDR"B"
MATCH
tBDA
tBDD
BUSY"B"
tWDD
DATAOUT "B"
VALID
(3)
tDDD
NOTES:
4840 drw 11
1. To ensure that the earlier of the two ports wins. tAPS is ignored for M/S = VIL (SLAVE).
2. CEL = CER = VIL, refer to Chip Enable Truth Table.
3. OE = VIL for the reading port.
4. If M/S = VIL (SLAVE), BUSY is an input. Then for this example BUSY "A" = VIH and BUSY "B" input is shown above.
5. All timing is the same for left and right ports. Port "A" may be either the left or right port. Port "B" is the port opposite from port "A".
Timing Waveform of Write with BUSY (M/S = VIL)
tWP
R/W"A"
(3)
tWB
BUSY"B"
(1)
tWH
R/W"B"
(2)
.
4840 drw 12
NOTES:
1. tWH must be met for both BUSY input (SLAVE) and output (MASTER).
2. BUSY is asserted on port "B" blocking R/W"B", until BUSY"B" goes HIGH.
3. tWB is only for the 'Slave' version.
11
6.42
IDT7019L
High-Speed 128K x 9 Dual-Port Static RAM
Industrial and Commercial Temperature Ranges
Waveform of BUSY Arbitration Controlled by CE Timing(M/S = VIH)(1,3)
ADDR"A"
ADDRESSES MATCH
and "B"
CE"A"
(2)
tAPS
CE"B"
tBAC
tBDC
BUSY"B"
4840 drw 13
Waveform of BUSY Arbitration Cycle Controlled by Address Match
Timing(M/S = VIH)(1)
ADDR"A"
ADDRESS "N"
(2)
tAPS
"B"
ADDR
MATCHING ADDRESS "N"
tBAA
tBDA
"B"
BUSY
4840 drw 14
NOTES:
1. All timing is the same for left and right ports. Port “A” may be either the left or right port. Port “B” is the port opposite from port “A”.
2. If tAPS is not satisfied, the BUSY signal will be asserted on one side or another but there is no guarantee on which side BUSY will be asserted.
3. Refer to Chip Enable Truth Table.
AC Electrical Characteristics Over the
OperatingTemperatureandSupplyVoltageRange(1)
7019L15
Com'l Only
7019L20
Com'l Only
Symbol
Parameter
Min.
Max.
Min. Max.
Unit
INTERRUPT TIMING
____
____
____
____
tAS
Address Set-up Time
0
0
ns
ns
ns
tWR
tINS
tINR
Write Recovery Time
Interrupt Set Time
0
0
____
____
15
15
20
20
____
____
Interrupt Reset Time
ns
4840 tbl 15
NOTES:
1. Industrial Temperature: for specific speeds, packages and powers contact your sales office.
12
IDT7019L
High-Speed 128K x 9 Dual-Port Static RAM
Industrial and Commercial Temperature Ranges
Waveform of Interrupt Timing(1,5)
tWC
INTERRUPT SET ADDRESS(2)
ADDR"A"
(3)
(4)
tAS
tWR
CE"A"
R/W"A"
INT"B"
(3)
tINS
4840 drw 15
tRC
INTERRUPT CLEAR ADDRESS (2)
ADDR"B"
CE"B"
(3)
tAS
OE"B"
(3)
tINR
INT"B"
4840 drw 16
NOTES:
1. All timing is the same for left and right ports. Port “A” may be either the left or right port. Port “B” is the port opposite from port “A”.
2. See Interrupt Truth Table.
3. Timing depends on which enable signal (CE or R/W) is asserted last.
4. Timing depends on which enable signal (CE or R/W) is de-asserted first.
5. Refer to Chip Enable Truth Table.
Truth Table IV Interrupt Flag(1,4,5)
Left Port
Right Port
WL
R/
WR
R/
A16L-A0L
1FFFF
X
A16R-A0R
X
Function
CEL
L
OEL
X
INTL
X
CER
X
OER
X
INT
R
(2)
L
X
X
X
X
X
L
L
Set Right INT Flag
R
(3
)
X
X
X
L
L
1FFFF
1FFFE
X
H
Reset Right INT Flag
R
(3)
X
X
X
L
L
X
X
X
Set Left INT Flag
L
(2)
L
L
1FFFE
H
X
X
X
Reset Left INT Flag
L
4840 tbl 16
NOTES:
1. Assumes BUSYL = BUSYR =VIH.
2. If BUSYL = VIL, then no change.
3. If BUSYR = VIL, then no change.
4. INTL and INTR must be initialized at power-up.
5. Refer to Chip Enable Truth Table.
13
6.42
IDT7019L
High-Speed 128K x 9 Dual-Port Static RAM
Industrial and Commercial Temperature Ranges
Truth Table V Address BUSY
Arbitration(4)
Inputs
Outputs
OL 16L
A -A
(1)
(1)
Function
Normal
Normal
Normal
Write
AOR-A16R
CEL CER
BUSYL
BUSYR
X
H
X
X
X
H
NO MATCH
MATCH
H
H
H
H
H
H
MATCH
L
L
MATCH
(2)
(2)
(3)
Inhibit
4840 tbl 17
NOTES:
1. Pins BUSYL and BUSYR are both outputs when the part is configured as a master. Both are inputs when configured as a slave. BUSY outputs on the IDT7019 are
push-pull, not open drain outputs. On slaves the BUSY input internally inhibits writes.
2. "L" if the inputs to the opposite port were stable prior to the address and enable inputs of this port. "H" if the inputs to the opposite port became stable after the address
and enable inputs of this port. If tAPS is not met, either BUSYL or BUSYR = LOW will result. BUSYL and BUSYR outputs can not be LOW simultaneously.
3. Writes to the left port are internally ignored when BUSYL outputs are driving LOW regardless of actual logic level on the pin. Writes to the right port are internally ignored
when BUSYR outputs are driving LOW regardless of actual logic level on the pin.
4. Refer to Chip Enable Truth Table.
Truth Table VI Example of Semaphore Procurement Sequence(1,2,3)
Functions
D0 - D8 Left
D0 - D8 Right
Status
No Action
1
0
0
1
1
0
1
1
1
0
1
1
1
1
0
0
1
1
0
1
1
1
Semaphore free
Left Port Writes "0" to Semaphore
Right Port Writes "0" to Semaphore
Left Port Writes "1" to Semaphore
Left Port Writes "0" to Semaphore
Right Port Writes "1" to Semaphore
Left Port Writes "1" to Semaphore
Right Port Writes "0" to Semaphore
Right Port Writes "1" to Semaphore
Left Port Writes "0" to Semaphore
Left Port Writes "1" to Semaphore
NOTES:
Left port has semaphore token
No change. Right side has no write access to semaphore
Right port obtains semaphore token
No change. Left port has no write access to semaphore
Left port obtains semaphore token
Semaphore free
Right port has semaphore token
Semaphore free
Left port has semaphore token
Semaphore free
4840 tbl 18
1. This table denotes a sequence of events for only one of the eight semaphores on the IDT7019.
2. There are eight semaphore flags written to via I/O0 and read from all I/O's (I/O0-I/O8). These eight semaphores are addressed by A0-A2.
3. CE = VIH, SEM = VIL to access the semaphores. Refer to the Semaphore Read/Write Control Truth Table.
FunctionalDescription
TheIDT7019providestwoportswithseparatecontrol,addressand (INTL)isassertedwhentherightportwritestomemorylocation1FFFE
I/Opinsthatpermitindependentaccessforreadsorwritestoanylocation (HEX), where a write is defined as CER = R/WR = VIL per Truth Table
inmemory.TheIDT7019hasanautomaticpowerdownfeaturecontrolled IV. The leftportclears the interruptthroughaccess ofaddress location
by CE. The CE0 and CE1 control the on-chip power down circuitry that 1FFFEwhenCEL=OEL =VIL,R/Wis a"don'tcare".Likewise,theright
permitstherespectiveporttogointoastandbymodewhennotselected portinterruptflag(INTR)isassertedwhentheleftportwritestomemory
(CE=HIGH).Whenaportisenabled,accesstotheentirememoryarray location1FFFF(HEX)andtocleartheinterruptflag(INTR),therightport
ispermitted.
mustreadthememorylocation1FFFF.Themessage(9bits)at1FFFE
or1FFFFisuser-definedsinceitisanaddressableSRAMlocation.Ifthe
interruptfunctionis notused,address locations 1FFFEand1FFFFare
notusedasmailboxes,butaspartoftherandomaccessmemory.Refer
toTableIVfortheinterruptoperation.
Interrupts
Iftheuserchoosestheinterruptfunction,amemorylocation(mailbox
ormessage center)is assignedtoeachport. The leftportinterruptflag
14
IDT7019L
High-Speed 128K x 9 Dual-Port Static RAM
Industrial and Commercial Temperature Ranges
BusyLogic
BusyLogicprovidesahardwareindicationthatbothportsoftheRAM
haveaccessedthesamelocationatthesametime.Italsoallowsoneofthe
twoaccessestoproceedandsignalstheothersidethattheRAMis“busy”.
TheBUSYpincanthenbeusedtostalltheaccessuntiltheoperationon
theothersideiscompleted.Ifawriteoperationhasbeenattemptedfrom
thesidethatreceivesaBUSYindication,thewritesignalisgatedinternally
topreventthewritefromproceeding.
TheuseofBUSYlogicisnotrequiredordesirableforallapplications.
InsomecasesitmaybeusefultologicallyORtheBUSYoutputstogether
anduse anyBUSYindicationas aninterruptsource toflagthe eventof
anillegalorillogicaloperation.IfthewriteinhibitfunctionofBUSYlogicis
notdesirable,theBUSYlogiccanbedisabledbyplacingthepartinslave
modewiththeM/Spin.OnceinslavemodetheBUSYpinoperatessolely
asawriteinhibitinputpin.Normaloperationcanbeprogrammedbytying
the BUSY pins HIGH. If desired, unintended write operations can be
prevented to a port by tying the BUSY pin for that port LOW.
TheBUSYoutputsontheIDT7019RAMinmastermode,arepush-
pulltypeoutputsanddonotrequirepullupresistorstooperate.Ifthese
RAMs are being expanded in depth, then the BUSY indication for the
resulting array requires the use of an external AND gate.
can result in a glitched internal write inhibit signal and corrupted data
inthe slave.
Semaphores
The IDT7019is anextremelyfastDual-Port128Kx9CMOSStatic
RAMwithanadditional8addresslocationsdedicatedtobinarysemaphore
flags.TheseflagsalloweitherprocessorontheleftorrightsideoftheDual-
PortRAMtoclaimaprivilegeovertheotherprocessorforfunctionsdefined
bythesystemdesigner’ssoftware.Asanexample,thesemaphorecan
beusedbyoneprocessortoinhibittheotherfromaccessingaportionof
the Dual-Port RAM or any other shared resource.
The Dual-PortRAMfeatures a fastaccess time, andbothports are
completelyindependentofeachother.Thismeansthattheactivityonthe
leftportinnowayslows theaccess timeoftherightport.Bothports are
identicalinfunctiontostandardCMOSStaticRAMandcanbereadfrom,
orwrittento,atthesametimewiththeonlypossibleconflictarisingfromthe
simultaneous writing of, or a simultaneous READ/WRITE of, a non-
semaphorelocation.Semaphoresareprotectedagainstsuchambiguous
situationsandmaybeusedbythesystemprogramtoavoidanyconflicts
inthenon-semaphoreportionoftheDual-PortRAM.Thesedeviceshave
anautomaticpower-downfeaturecontrolledbyCE,theDual-PortRAM
enable,andSEM,thesemaphoreenable.TheCEandSEMpinscontrol
on-chippowerdowncircuitrythatpermits the respective porttogointo
standbymodewhennotselected. Thisistheconditionwhichisshownin
Truth Table II where CE and SEM are both HIGH.
17
A
CE0
CE0
MASTER
SLAVE
Dual Port RAM
Dual Port RAM
BUSYL
BUSYR
BUSYL
BUSYR
SystemswhichcanbestusetheIDT7019containmultipleprocessors
or controllers and are typically very high-speed systems which are
software controlled or software intensive. These systems can benefit
from a performance increase offered by the IDT7019s hardware
semaphores, which provide a lockout mechanism without requiring
complexprogramming.
CE1
CE1
MASTER
Dual Port RAM
SLAVE
Dual Port RAM
BUSYL BUSYR
BUSYL
BUSYR
,
4840 drw 17
Softwarehandshakingbetweenprocessors offers themaximumin
systemflexibilitybypermittingsharedresourcestobeallocatedinvarying
configurations.TheIDT7019doesnotuseitssemaphoreflagstocontrol
anyresourcesthroughhardware,thusallowingthesystemdesignertotal
flexibilityinsystemarchitecture.
An advantage of using semaphores rather than the more common
methodsofhardwarearbitrationisthatwaitstatesareneverincurredin
either processor. This can prove to be a major advantage in very high-
speedsystems.
Figure 3. Busy and chip enable routing for both width and depth
expansion with IDT7019 RAMs.
WidthExpansionBusyLogic
Master/SlaveArrays
WhenexpandinganIDT7019RAMarrayinwidthwhileusingBUSY
logic,onemasterpartisusedtodecidewhichsideoftheRAMsarraywill
receivea BUSYindication,andtooutputthatindication.Anynumberof
slaves to be addressed in the same address range as the master, use
the BUSYsignalasawriteinhibitsignal.ThusontheIDT7019RAMthe
BUSYpinisanoutputifthepartisusedasamaster(M/Spin=VIH),and
theBUSYpinisaninputifthepartusedasaslave(M/Spin=VIL)as shown
in Figure 3.
Iftwoormoremasterpartswereusedwhenexpandinginwidth,asplit
decisioncouldresultwithonemasterindicatingBUSYononesideofthe
arrayandanothermasterindicatingBUSYononeothersideofthearray.
Thiswouldinhibitthewriteoperationsfromoneportforpartofawordand
inhibitthewriteoperationsfromtheotherportfortheotherpartoftheword.
TheBUSYarbitration,onamaster,is basedonthechipenableand
address signals only. Itignores whetheranaccess is a readorwrite. In
a master/slave array, both address and chip enable must be valid long
enough for a BUSYflag to be output from the master before the actual
writepulsecanbeinitiatedwiththeR/Wsignal.Failuretoobservethistiming
How the Semaphore Flags Work
Thesemaphorelogicisasetofeightlatcheswhichareindependent
oftheDual-PortRAM.Theselatchescanbeusedtopassaflag,ortoken,
fromoneporttotheothertoindicatethatasharedresourceisinuse.The
semaphores provide a hardware assist for a use assignment method
called“TokenPassingAllocation.”Inthismethod,thestateofasemaphore
latchisusedasatokenindicatingthatsharedresourceisinuse.Iftheleft
processorwantstousethisresource,itrequeststhetokenbysettingthe
latch.Thisprocessorthenverifiesitssuccessinsettingthelatchbyreading
it. If it was successful, it proceeds to assume control over the shared
resource.Ifitwasnotsuccessfulinsettingthelatch,itdeterminesthatthe
rightsideprocessorhassetthelatchfirst, hasthetokenandisusingthe
sharedresource. Theleftprocessorcantheneitherrepeatedlyrequest
thatsemaphore’sstatusorremoveitsrequestforthatsemaphoretoperform
15
6.42
IDT7019L
High-Speed 128K x 9 Dual-Port Static RAM
Industrial and Commercial Temperature Ranges
anothertaskandoccasionallyattemptagaintogaincontrolofthetokenvia side during subsequent read. Had a sequence of READ/WRITE been
thesetandtestsequence.Oncetherightsidehasrelinquishedthetoken, usedinstead,systemcontentionproblemscouldhaveoccurredduringthe
theleftsideshouldsucceedingainingcontrol.
gap between the read and write cycles.
ThesemaphoreflagsareactiveLOW.Atokenisrequestedbywriting
Itisimportanttonotethatafailedsemaphorerequestmustbefollowed
azerointoasemaphorelatchandisreleasedwhenthesamesidewrites byeitherrepeatedreadsorbywritingaoneintothesamelocation.The
aonetothatlatch. reasonforthisiseasilyunderstoodbylookingatthesimplelogicdiagram
The eightsemaphore flags reside withinthe IDT7019ina separate ofthesemaphoreflaginFigure4.Twosemaphorerequestlatchesfeed
memoryspacefromtheDual-PortRAM.This addressspaceisaccessed into a semaphore flag. Whichever latch is first to present a zero to the
byplacingaLOWinputontheSEMpin(whichactsasachipselectforthe semaphoreflagwillforceitssideofthesemaphoreflagLOWandtheother
semaphore flags) and using the other control pins (Address, CE, and sideHIGH.Thisconditionwillcontinueuntilaoneiswrittentothesame
R/W)as theywouldbeusedinaccessingastandardStaticRAM.Each semaphorerequestlatch.Shouldtheotherside’ssemaphorerequestlatch
oftheflagshasauniqueaddresswhichcanbeaccessedbyeitherside havebeenwrittentoazerointhemeantime,thesemaphoreflagwillflip
throughaddresspinsA0–A2.Whenaccessingthesemaphores,noneof
theotheraddresspinshasanyeffect.
L PORT
R PORT
Whenwritingtoasemaphore,onlydatapinD0isused.IfaLOWlevel
iswrittenintoanunusedsemaphorelocation,thatflagwillbesettoazero
onthatsideandaoneontheotherside(seeTableVI).Thatsemaphore
can now only be modified by the side showing the zero. When a one is
writtenintothesamelocationfromthesameside,theflagwillbesettoa
one for both sides (unless a semaphore request from the other side is
pending)andthencanbewrittentobybothsides.Thefactthattheside
whichisabletowriteazerointoasemaphoresubsequentlylocksoutwrites
fromtheothersideiswhatmakessemaphoreflagsusefulininterprocessor
communications.(Athoroughdiscussionontheuseofthisfeaturefollows
shortly.)Azerowrittenintothesamelocationfromtheothersidewillbe
storedinthesemaphorerequestlatchforthatsideuntilthesemaphoreis
freedbythefirstside.
Whenasemaphoreflagisread,itsvalueisspreadintoalldatabitsso
thataflagthatisaonereadsasaoneinalldatabitsandaflagcontaining
azeroreadsasallzeros.Thereadvalueislatchedintooneside’soutput
registerwhenthatside'ssemaphoreselect(SEM)andoutputenable(OE)
signalsgoactive.Thisservestodisallowthesemaphorefromchanging
stateinthemiddleofareadcycleduetoawritecyclefromtheotherside.
Becauseofthislatch,arepeatedreadofasemaphoreinatestloopmust
cause either signal (SEM or OE) to go inactive or the output will never
change.
AsequenceWRITE/READmustbeusedbythesemaphoreinorder
to guarantee that no system level contention will occur. A processor
requestsaccesstosharedresourcesbyattemptingtowriteazerointoa
semaphorelocation.Ifthesemaphoreisalreadyinuse,thesemaphore
requestlatchwillcontainazero,yetthesemaphoreflagwillappearasone,
afactwhichtheprocessorwillverifybythesubsequentread(seeTable
VI). As anexample, assume a processorwrites a zerotothe leftportat
afreesemaphorelocation.Onasubsequentread,theprocessorwillverify
thatithaswrittensuccessfullytothatlocationandwillassumecontrolover
the resource in question. Meanwhile, if a processor on the right side
attempts towriteazerotothesamesemaphoreflagitwillfail,as willbe
verifiedbythefactthataonewillbereadfromthatsemaphoreontheright
SEMAPHORE
REQUEST FLIP FLOP
SEMAPHORE
REQUEST FLIP FLOP
D0
D0
D
D
Q
Q
WRITE
WRITE
SEMAPHORE
READ
SEMAPHORE
READ
4840 drw 18
Figure 4. IDT7019 Semaphore Logic
overtotheothersideassoonasaoneiswrittenintothefirstside’srequest
latch.Thesecondside’sflagwillnowstayLOWuntilitssemaphorerequest
latchiswrittentoaone.Fromthisitiseasytounderstandthat,ifasemaphore
is requestedandthe processorwhichrequesteditnolongerneeds the
resource, the entire system can hang up until a one is written into that
semaphorerequestlatch.
The criticalcase ofsemaphore timingis whenbothsides requesta
single token by attempting to write a zero into it at the same time. The
semaphorelogicisspeciallydesignedtoresolvethisproblem.Ifsimulta-
neousrequestsaremade,thelogicguaranteesthatonlyonesidereceives
thetoken.Ifonesideisearlierthantheotherinmakingtherequest,thefirst
sidetomaketherequestwillreceivethetoken.Ifbothrequestsarriveat
thesametime,theassignmentwillbearbitrarilymadetooneportorthe
other.
One caution that should be noted when using semaphores is that
semaphoresalonedonotguaranteethataccesstoaresourceissecure.
Aswithanypowerfulprogrammingtechnique,ifsemaphoresaremisused
ormisinterpreted, a software errorcaneasilyhappen.
Initializationofthesemaphoresisnotautomaticandmustbehandled
viatheinitializationprogramatpower-up.Sinceanysemaphorerequest
flagwhichcontainsazeromustberesettoaone,allsemaphoresonboth
sidesshouldhaveaonewrittenintothematinitializationfrombothsides
to assure that they will be free when needed.
16
IDT7019L
High-Speed 128K x 9 Dual-Port Static RAM
Industrial and Commercial Temperature Ranges
OrderingInformation
IDT XXXXX
A
999
A
A
Device
Type
Power
Speed
Package
Process/
Temperature
Range
Blank
Commercial (0 C to +70 C)
°
°
I(1)
Industrial (-40 C to +85 C)
°
°
PF
100-pin TQFP (PN100-1)
Commercial Only
Commercial Only
15
20
Speed in
nanoseconds
Low Power
L
1152K (128K x 9) Dual-Port RAM
7019
4840 drw 19
NOTE:
1. Industrial temperature range is available.
For specific speeds, packages and powers contact your sales office.
DatasheetDocumentHistory
9/30/99:
11/10/99:
1/12/01:
InitialPublicRelease
Replaced IDT logo
Page 3 Increasedstoragetemperatureparameter
ClarifiedTAparameter
Page 5 DCElectricalparameters–changedwordingfrom"open"to"disabled"
Page 14 Added IV to Truth Table in "Interrupts" paragraph
Changed±200mVto0mVinnotes
RemovedPreliminarystatus
CORPORATE HEADQUARTERS
2975StenderWay
Santa Clara, CA 95054
for SALES:
for Tech Support:
831-754-4613
DualPortHelp@idt.com
800-345-7015 or 408-727-6116
fax: 408-492-8674
www.idt.com
The IDT logo is a registered trademark of Integrated Device Technology, Inc.
17
6.42
相关型号:
IDT7019L20PFI8
Dual-Port SRAM, 128KX9, 20ns, CMOS, PQFP100, 14 X 14 MM, 1.40 MM HEIGHT, TQFP-100
IDT
IDT7024L15FG
Dual-Port SRAM, 4KX16, 15ns, CMOS, 1.170 X 1.170 INCH, 0.110 INCH HEIGHT, GREEN, QFP-84
IDT
IDT7024L15GG
Dual-Port SRAM, 4KX16, 15ns, CMOS, CPGA84, 1.120 X 1.120 INCH, 0.160 INCH HEIGHT, GREEN, CERAMIC, PGA-84
IDT
©2020 ICPDF网 联系我们和版权申明