IDT7005L35FI [IDT]
Dual-Port SRAM, 8KX8, 35ns, CMOS, 0.970 X 0.970 INCH, 0.080 INCH HEIGHT, QFP-68;型号: | IDT7005L35FI |
厂家: | INTEGRATED DEVICE TECHNOLOGY |
描述: | Dual-Port SRAM, 8KX8, 35ns, CMOS, 0.970 X 0.970 INCH, 0.080 INCH HEIGHT, QFP-68 存储 内存集成电路 静态存储器 |
文件: | 总20页 (文件大小:265K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
IDT7005S/L
HIGH-SPEED
8K x 8 DUAL-PORT
STATIC RAM
Integrated Device Technology, Inc.
• Busy and Interrupt Flags
• On-chip port arbitration logic
• Full on-chip hardware support of Semaphore signaling
between ports
FEATURES:
• True Dual-Ported memory cells which allow simulta-
neous access of the same memory location
• High-speed access
• Fully asynchronous operation from either port
• Devices are capable of withstanding greater than 2001V
electrostatic discharge
— Military: 20/25/35/55/70ns (max.)
— Commercial:15/17/20/25/35/55ns (max.)
• Low-power operation
• Battery backup operation—2V data retention
• TTL-compatible, single 5V (±10%) power supply
• Available in 68-pin PGA, 68-pin quad flatpack, 68-pin
PLCC, and a 64-pin TQFP
• Industrial temperature range (–40°C to +85°C) is avail-
able, tested to military electrical specifications
— IDT7005S
Active: 750mW (typ.)
Standby: 5mW (typ.)
— IDT7005L
Active: 750mW (typ.)
Standby: 1mW (typ.)
• IDT7005 easily expands data bus width to 16 bits or
more using the Master/Slave select when cascading
more than one device
• M/S = H for BUSY output flag on Master,
M/S = L for BUSY input on Slave
DESCRIPTION:
The IDT7005 is a high-speed 8K x 8 Dual-Port Static RAM.
The IDT7005 is designed to be used as a stand-alone Dual-
Port RAM or as a combination MASTER/SLAVE Dual-Port
FUNCTIONAL BLOCK DIAGRAM
OER
OEL
CE
L
CE
R
R/WR
R/W
L
I/O0L- I/O7L
I/O0R-I/O7R
(1,2)
I/O
Control
I/O
Control
BUSY (1,2)
L
BUSY
R
A
12L
A
12R
0R
Address
Decoder
MEMORY
ARRAY
Address
Decoder
A
0L
A
13
13
ARBITRATION
INTERRUPT
SEMAPHORE
LOGIC
NOTES:
CE
OE
R/W
L
CE
OE
R/W
R
1. (MASTER):
BUSY is output;
(SLAVE): BUSY
is input.
R
L
R
L
2. BUSY outputs
and INT outputs
are non-tri-stated
push-pull.
SEM
L
SEM
R
INT (2)
L
(2)
INTR
2738 drw 01
M/S
The IDT logo is a registered trademark of Integrated Device Technology, Inc.
MILITARY AND COMMERCIAL TEMPERATURE RANGES
OCTOBER 1996
For latest information contact IDT’s web site at www.idt.com or fax-on-demand at 408-492-8391.
©1996 Integrated Device Technology, Inc.
DSC-2738/6
1
6.06
IDT7005S/L
HIGH-SPEED 8K x 8 DUAL-PORT STATIC RAM
MILITARY AND COMMERCIAL TEMPERATURE RANGES
RAM for 16-bit-or-more word systems. Using the IDT MAS- ogy, these devices typically operate on only 750mW of power.
TER/SLAVE Dual-Port RAM approach in 16-bit or wider Low-power (L) versions offer battery backup data retention
memory system applications results in full-speed, error-free capabilitywithtypicalpowerconsumptionof500µWfroma2V
operation without the need for additional discrete logic.
This device provides two independent ports with separate
battery.
The IDT7005 is packaged in a ceramic 68-pin PGA, a 68-
control, address, and I/O pins that permit independent, pin quad flatpack, a 68-pin PLCC and a 64-pin Thin Plastic
asynchronous access for reads or writes to any location in Quad Flatpack (TQFP). Military grade product is manufac-
memory. An automatic power down feature controlled by CE tured in compliance with the latest revision of MIL-STD-883,
permits the on-chip circuitry of each port to enter a very low Class B, making it ideally suited to military temperature
standby power mode.
applications demanding the highest level of performance and
Fabricated using IDT’s CMOS high-performance technol- reliability.
PIN CONFIGURATIONS (1,2)
INDEX
9
8
7
6
5
4
3
2
1
68 67 66 65 64 63 62 61
60
I/O2L
I/O3L
I/O4L
I/O5L
GND
I/O6L
I/O7L
A
A
A
A
A
A
5L
4L
3L
2L
1L
0L
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
59
58
57
56
IDT7005
J68-1
55
54
53
52
51
50
49
48
47
46
45
44
F68-1
INT
BUSY
GND
M/
BUSY
INT
L
V
CC
L
GND
I/O0R
I/O1R
I/O2R
PLCC / FLATPACK
(3)
S
TOP VIEW
R
R
V
CC
A
A
A
A
A
0R
I/O3R
I/O4R
I/O5R
I/O6R
1R
2R
3R
4R
27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43
2738 drw 02
INDEX
1
2
3
4
5
6
48
47
46
45
44
43
42
41
40
39
38
37
I/O2L
I/O3L
A
A
A
A
A
4L
3L
2L
1L
0L
I/O4L
I/O5L
GND
I/O6L
I/O7L
IDT7005
PN-64
INT
L
7
8
BUSY
L
V
CC
GND
TQFP
TOP VIEW
9
GND
I/O0R
I/O1R
(3)
M/S
10
11
12
BUSY
R
INT
R
I/O2R
A
A
A
A
A
0R
13
14
15
16
V
CC
36
35
34
33
1R
2R
3R
4R
I/O3R
I/O4R
I/O5R
2738 drw 03
NOTES:
1. All Vcc pins must be connected to the power supply.
2. All GND pins must be connected to the ground supply.
3. This text does not indicate orientation of the the actual part-marking.
6.06
2
IDT7005S/L
HIGH-SPEED 8K x 8 DUAL-PORT STATIC RAM
MILITARY AND COMMERCIAL TEMPERATURE RANGES
PIN CONFIGURATIONS (CON'T.)(1,2)
51
50
48
A
46
A
44
BUSY
42
M/S
40
INT
38
36
11
10
09
08
07
06
05
04
03
02
01
A4L
2L
1L
0L
A1R
A
3R
L
R
A
5L
6L
53
A
52
49
47
A
45
INT
43
GND
41
BUSY
39
37
35
34
L
R
A
4R
7L
A3L
A
0R
A2R
A
5R
6R
8R
A
55
A
54
32
33
A
A
7R
9L
A
8L
57
A
56
A
30
31
A
A
9R
11L
10L
12L
59
58
A
28
29
A
A
11R
10R
12R
V
CC
IDT7005
G68-1
61
60
26
GND
27
A
N/C
N/C
68-PIN PGA
(3)
TOP VIEW
63
62
24
N/C
25
N/C
SEM
L
CE
L
65
64
22
SEM
23
CER
R
OE
L
R/W
L
67
I/O0L
66
20
OE
21
R/W
R
R
N/C
1
3
5
GND
7
9
68
I/O1L
11
13
V
15
18
I/O7R
19
N/C
GND
I/O7L
CC
I/O4L
I/O2L
I/O1R
I/O4R
2
4
6
8
10
12
14
16
17
I/O6R
I/O5L
I/O0R I/O2R I/O3R I/O5R
V
CC
I/O6L
I/O3L
A
B
C
D
E
F
G
H
J
K
L
INDEX
2738 drw 04
NOTES:
1. All VCC pins must be connected to power supply.
2. All GND pins must be connected to ground supply.
3. This text does not indicate oriention of the actual part-marking
PIN NAMES
Left Port
CEL
Right Port
CER
Names
Chip Enable
R/WL
R/WR
Read/Write Enable
Output Enable
Address
OEL
OER
A0L – A12L
I/O0L – I/O7L
SEML
A0R – A12R
I/O0R – I/O7R
SEMR
Data Input/Output
Semaphore Enable
Interrupt Flag
Busy Flag
INTL
INTR
BUSYL
BUSYR
M/S
VCC
Master or Slave Select
Power
GND
Ground
2738 tbl 01
6.06
3
IDT7005S/L
HIGH-SPEED 8K x 8 DUAL-PORT STATIC RAM
MILITARY AND COMMERCIAL TEMPERATURE RANGES
TRUTH TABLE I – NON-CONTENTION READ/WRITE CONTROL
Inputs(1)
Outputs
CE
R/W
OE
X
SEM
H
I/O0-7
Mode
H
X
L
High-Z
Deselected: Power-Down
Write to Memory
L
X
H
DATAIN
DATAOUT
High-Z
L
X
H
X
L
H
Read Memory
H
X
Outputs Disabled
NOTE:
2738 tbl 02
1. A0L — A12L is not equal to A0R — A12R.
TRUTH TABLE II – SEMAPHORE READ/WRITE CONTROL(1)
Inputs
Outputs
CE
R/W
OE
L
SEM
I/O0-7
Mode
Read in Semaphore Flag Data 0ut
H
H
H
L
L
L
DATAOUT
DATAIN
—
X
Write I/O0 into Semaphore Flag
Not Allowed
L
X
X
2738 tbl 03
NOTE:
1. There are eight semaphore flags written to via I/O0 and read from I/O0 - I/O15. These eight semaphores are addressed by A0 - A2.
ABSOLUTE MAXIMUM RATINGS(1)
RECOMMENDED OPERATING
Symbol
Rating
Commercial
Military
Unit
TEMPERATURE AND SUPPLY VOLTAGE
(2)
Ambient
VTERM
Terminal Voltage –0.5 to +7.0 –0.5 to +7.0
V
Grade
Military
Commercial
Temperature
GND
0V
VCC
with Respect
to GND
–55°C to +125°C
0°C to +70°C
5.0V ± 10%
TA
Operating
Temperature
0 to +70
–55 to +125 °C
0V
5.0V ± 10%
2738 tbl 05
TBIAS
TSTG
IOUT
Temperature
Under Bias
–55 to +125 –65 to +135 °C
–55 to +125 –65 to +150 °C
RECOMMENDED DC OPERATING
CONDITIONS
Storage
Temperature
Symbol
Parameter
Supply Voltage
Supply Voltage
Min. Typ. Max. Unit
VCC
4.5
0
5.0
0
5.5
0
V
V
DC Output
Current
50
50
mA
GND
NOTES:
2738 tbl 04
VIH
VIL
Input High Voltage
Input Low Voltage
2.2
–0.5(1)
—
—
6.0(2)
V
V
1. Stresses greater than those listed under ABSOLUTE MAXIMUM
RATINGS may cause permanent damage to the device. This is a stress
rating only and functional operation of the device at these or any other
conditions above those indicated in the operational sections of this
specification is not implied. Exposure to absolute maximum rating
conditions for extended periods may affect reliability.
0.8
NOTES:
2738 tbl 06
1. VIL > -1.5V for pulse width less than 10ns.
2. VTERM must not exceed Vcc + 0.5V.
2. VTERM must not exceed Vcc + 0.5V for more than 25% of the cycle time
or 10% maximum, and is limited to < 20mA for the period of VTERM > Vcc
+ 0.5V.
CAPACITANCE(1)
(TA = +25°C, f = 1.0MHz) TQFP PACKAGE
Symbol
CIN
Parameter
Conditions(2) Max. Unit
Input Capacitance
VIN = 3dV
9
pF
pF
COUT
Output
VOUT = 3dV
10
Capacitance
NOTES:
2738 tbl 07
1. This parameter is determined by device characterization but is not
production tested.
2. 3dv references the interpolated capacitance when the input and output
signals switch from 0V to 3V or from 3V to 0V.
6.06
4
IDT7005S/L
HIGH-SPEED 8K x 8 DUAL-PORT STATIC RAM
MILITARY AND COMMERCIAL TEMPERATURE RANGES
DC ELECTRICAL CHARACTERISTICS OVER THE
OPERATING TEMPERATURE AND SUPPLY VOLTAGE RANGE (VCC = 5.0V ± 10%)
IDT7005S
IDT7005L
Symbol
Parameter
Input Leakage Current(1)
Output Leakage Current
Output Low Voltage
Test Conditions
VCC = 5.5V, VIN = 0V to VCC
CE = VIH, VOUT = 0V to VCC
IOL = 4mA
Min.
Max.
10
Min.
—
Max.
5
Unit
µA
|ILI|
—
—
|ILO|
VOL
VOH
10
—
5
µA
—
0.4
—
—
0.4
—
V
Output High Voltage
IOH = -4mA
2.4
2.4
V
NOTE:
1. At Vcc < 2.0V input leakages are undefined.
2738 tbl 08
DC ELECTRICAL CHARACTERISTICS OVER THE
OPERATING TEMPERATURE AND SUPPLY VOLTAGE RANGE(1) (VCC = 5.0V ± 10%)
7005X15
Com'l. Only Com'l. Only
Version Typ.(2) Max. Typ.(2) Max. Typ.(2) Max. Typ.(2) Max. Unit
7005X17
7005X20
7005X25
Test
Symbol
Parameter
Condition
ICC
Dynamic Operating CE = VIL, Outputs Open
MIL.
COM.
MIL.
COM.
MIL.
S
L
—
—
—
—
—
—
—
—
160 370
150 320
155 340 mA
145 280
Current
SEM = VIH
(3)
(Both Ports Active) f = fMAX
S
L
170 310
160 260
170 310
160 260
160 290
150 240
155 265
145 220
ISB1 Standby Current
CEL = CER = VIH
(Both Ports — TTL SEMR = SEML = VIH
S
L
—
—
—
—
—
—
—
—
20
10
90
70
16
10
80 mA
65
(3)
Level Inputs
f = fMAX
S
L
20
10
60
60
20
10
60
50
20
10
60
50
16
10
60
50
(5)
ISB2 Standby Current
(One Port — TTL
Level Inputs)
CE"A"=VIL and CE"B"=VIH
S
L
—
—
—
—
—
—
—
—
95
85
95
85
240
210
180
150
90
80
90
80
215 mA
180
Active Port Outputs Open
(3)
f = fMAX
COM.
S
L
105 190
105 190
95 160
170
SEMR = SEML > VIH
95
160
140
ISB3 Full Standby Current Both Ports CEL and
(Both Ports — All
CER > VCC - 0.2V(5)
MIL.
S
L
—
—
—
—
—
—
—
—
1.0
0.2
30
10
1.0
0.2
30 mA
10
CMOS Level Inputs) VIN > VCC - 0.2V or
VIN < 0.2V, f = 0(4)
COM.
S
L
1.0
0.2
15
5
1.0
0.2
15
5
1.0
0.2
15
5
1.0
0.2
15
5
SEMR = SEML > VCC - 0.2V
ISB4 Full Standby Current CE"B" < 0.2V and
(One Port — All CE"B" > VCC - 0.2v
MIL.
S
—
—
—
—
—
—
—
—
90
225
85
200 mA
CMOS Level Inputs) SEMR = SEML > VCC - 0.2V
VIN > VCC - 0.2V or
L
80
90
200
155
75
85
170
145
COM
.
S
100 170
100 170
VIN < 0.2V
Active Port Outputs Open,
f = fMAX
L
90 140
90 140
80
130
75
120
(3)
NOTES:
1. "X" in part numbers indicates power rating (S or L).
2. VCC = 5V, TA = +25°C, and are not production tested. ICC DC = 120mA typ.)
2738 tbl 09
3. At f = fMAX, address and I/O'S are cycling at the maximum frequency read cycle of 1/tRC, and using “AC Test Conditions” of input levels of GND to 3V.
4. f = 0 means no address or control lines change.
5. Port "A"may be either left or right port. Port "B" is the port opposite port "A".
6.06
5
IDT7005S/L
HIGH-SPEED 8K x 8 DUAL-PORT STATIC RAM
MILITARY AND COMMERCIAL TEMPERATURE RANGES
DC ELECTRICAL CHARACTERISTICS OVER THE
OPERATING TEMPERATURE AND SUPPLY VOLTAGE RANGE(1)(Cont'd.) (VCC = 5.0V ± 10%)
7005X35
7005X55
7005X70
Mil. Only
Test
Symbol
Parameter
Condition
Version
MIL.
Typ.(2) Max. Typ.(2) Max. Typ.(2) Max. Unit
ICC
Dynamic Operating
Current
CE = VIL, Outputs Open
SEM = VIH
S
L
150
140
300
250
150
140
300
250
140
130
300 mA
250
(3)
(Both Ports Active)
f = fMAX
COM’L.
MIL.
S
L
150
140
250
210
150
140
250
210
—
—
—
—
ISB1
ISB2
Standby Current
(Both Ports — TTL
CEL = CER = VIH
SEMR = SEML = VIH
S
L
13
10
80
65
13
10
80
65
10
10
80 mA
65
(3)
Level Inputs)
f = fMAX
COM’L.
MIL.
S
L
13
10
60
50
13
10
60
50
—
—
—
—
(5)
Standby Current
(One Port — TTL
Level Inputs)
CE"A"=VIL and CE"B"=VIL
S
L
85
75
85
75
190
160
155
130
85
75
85
75
190
160
155
130
80
70
—
—
190 mA
Active Port Outputs Open
160
—
(3)
f = fMAX
COM’L.
S
L
SEMR = SEML = VIH
—
ISB3
ISB4
Full Standby Current
(Both Ports — All
Both Ports CEL and
CER > VCC - 0.2V
MIL.
S
L
1.0
0.2
30
10
1.0
0.2
30
10
1.0
0.2
30 mA
10
CMOS Level Inputs)
VIN > VCC - 0.2V or
COM’L.
S
L
1.0
0.2
15
5
1.0
0.2
15
5
—
—
—
—
VIN < 0.2V, f = 0(4)
SEMR = SEML > VCC - 0.2V
Full Standby Current
(One Port — All
One Port CE"A" < 0.2V
CE"B" > VCC - 0.2V(5)
MIL.
S
80
175
80
175
75
175 mA
CMOS Level Inputs)
SEMR = SEML > VCC - 0.2V
VIN > VCC - 0.2V or
VIN < 0.2V
L
70
80
150
135
70
80
150
135
65
—
150
—
COM’L.
S
Active Port Outputs Open,
f = fMAX
L
70
110
80
110
—
—
(3)
NOTES:
2738 tbl 10
1. "X" in part numbers indicates power rating (S or L).
2. VCC = 5V, TA = +25°C and are not production tested. ICC DC = 120mA (typ.)
3. At f = fMAX, address and I/O'S are cycling at the maximum frequency read cycle of 1/tRC, and using “AC Test Conditions” of input levels of GND to 3V.
4. f = 0 means no address or control lines change.
5. Port "A" may be either left or right port. Port "B" is the port opposite port "A".
DATA RETENTION CHARACTERISTICS OVER ALL TEMPERATURE RANGES (L Version Only)
(VLC = 0.2V, VHC = VCC - 0.2V)(4)
Symbol
Parameter
VCC for Data Retention
Data Retention Current
Test Condition
VCC = 2V
Min.
2.0
—
Typ.(1)
—
Max.
—
Unit
V
VDR
ICCDR
CE > VHC
MIL.
100
100
—
4000
1500
—
µA
VIN > VHC or ≤ VLC
SEM > VHC
COM’L.
—
(3)
tCDR
Chip Deselect to Data Retention Time
Operation Recovery Time
0
ns
(3)
(2)
tR
tRC
—
—
ns
NOTES:
2738 tbl 11
1. TA = +25°C, VCC = 2V, and are not production tested.
2. tRC = Read Cycle Time
3. This parameter is guaranteed by device characteriation, but is not production tested.
DATA RETENTION WAVEFORM
DATA RETENTION MODE
V
DR
≥
VCC
4.5V
4.5V
2V
t
CDR
tR
V
DR
V
IH
VIH
CE
2738 drw 05
6.06
6
IDT7005S/L
HIGH-SPEED 8K x 8 DUAL-PORT STATIC RAM
MILITARY AND COMMERCIAL TEMPERATURE RANGES
5V 5V
AC TEST CONDITIONS
1250Ω
Input Pulse Levels
GND to 3.0V
5ns Max.
1.5V
1250Ω
DATAOUT
BUSY
INT
Input Rise/Fall Times
Input Timing Reference Levels
Output Reference Levels
Output Load
DATAOUT
775Ω
5pF
775Ω
30pF
1.5V
Figure 1 and 2
2738 drw 06
2738 tbl 12
Figure 2. Output Load
(For tLZ, tHZ, tWZ, tOW)
Figure 1. AC Output Test Load
Including scope and jig
AC ELECTRICAL CHARACTERISTICS OVER THE
OPERATING TEMPERATURE AND SUPPLY VOLTAGE RANGE(4)
IDT7005X15
Com'l. Only
Min. Max.
IDT7005X17
Com'l. Only
IDT7005X20
IDT7005X25
Symbol
Parameter
Min.
Max.
Min.
Max.
Min.
Max. Unit
READ CYCLE
tRC
tAA
Read Cycle Time
15
—
—
—
3
—
15
15
10
17
—
—
—
3
—
17
17
10
—
—
10
—
17
—
17
20
—
—
—
3
—
20
20
12
—
—
12
—
20
—
20
25
—
—
—
3
—
25
25
13
—
—
15
—
25
—
25
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
Address Access Time
tACE
tAOE
tOH
tLZ
Chip Enable Access Time(3)
Output Enable Access Time
Output Hold from Address Change
Output Low-Z Time(1, 2)
3
—
3
3
3
tHZ
Output High-Z Time(1, 2)
10
—
0
—
0
—
0
tPU
Chip Enable to Power Up Time(2)
Chip Disable to Power Down Time(2)
Semaphore Flag Update Pulse (OE or SEM)
Semaphore Address Access Time
0
tPD
15
15
—
10
—
—
10
—
—
10
—
tSOP
tSAA
10
IDT7005X35
IDT7005X55
IDT7005X70
Mil. Only
Symbol
Parameter
Min.
Max.
Min.
Max.
Min.
Max. Unit
READ CYCLE
tRC
tAA
Read Cycle Time
35
—
—
—
3
—
35
35
20
—
—
15
—
35
—
35
55
—
—
—
3
—
55
55
30
—
—
25
—
50
—
55
70
—
—
—
3
—
70
70
35
—
—
30
—
50
—
70
ns
ns
Address Access Time
tACE
tAOE
tOH
tLZ
Chip Enable Access Time(3)
Output Enable Access Time
Output Hold from Address Change
Output Low-Z Time(1, 2)
ns
ns
ns
3
3
3
ns
tHZ
Output High-Z Time(1, 2)
—
0
—
0
—
0
ns
tPU
Chip Enable to Power Up Time(2)
Chip Disable to Power Down Time(2)
Semaphore Flag Update Pulse (OE or SEM)
Semaphore Address Access Time
ns
tPD
—
15
—
—
15
—
—
15
—
ns
tSOP
tSAA
ns
ns
NOTES:
2738 tbl 13
1. Transition is measured ±500mV from Low or High-impedance voltage with Output Test Load (Figures 2).
2. This parameter is guaranteed by device characterization but not production tested.
3. To access RAM, CE = VIL and SEM = VIH. To access semaphore, CE = VIH and SEM = VIL.
4. "X" in part numbers indicates power rating (S or L).
6.06
7
IDT7005S/L
HIGH-SPEED 8K x 8 DUAL-PORT STATIC RAM
MILITARY AND COMMERCIAL TEMPERATURE RANGES
WAVEFORM OF READ CYCLES(5)
t
RC
ADDR
(4)
t
t
AA
(4)
ACE
CE
OE
(4)
t
AOE
R/W
DATAOUT
BUSYOUT
t
OH
(1)
t
LZ
(4)
VALID DATA
(2)
t
HZ
(3, 4)
t
BDD
2738 drw 07
NOTES:
1. Timing depends on which signal is asserted last, OE or CE.
2. Timing depends on which signal is de-asserted first, CE or OE.
3. tBDDdelayisrequiredonlyincaseswheretheoppositeportiscompletingawriteoperationtothesameaddresslocation. Forsimultaneous readoperations
BUSY has no relation to valid output data.
4. Start of valid data depends on which timing becomes effective last tAOE, tACE, tAA or tBDD.
5. SEM = VIH.
TIMING OF POWER-UP POWER-DOWN
CE
t
PU
tPD
I
CC
SB
50%
50%
I
2738 drw 08
6.06
8
IDT7005S/L
HIGH-SPEED 8K x 8 DUAL-PORT STATIC RAM
MILITARY AND COMMERCIAL TEMPERATURE RANGES
AC ELECTRICAL CHARACTERISTICS OVER THE
OPERATING TEMPERATURE AND SUPPLY VOLTAGE (5)
IDT7005X15
Com'l. Only
IDT7005X17
Com'l. Only
IDT7005X20
IDT7005X25
Symbol
Parameter
Min.
Max.
Min.
Max.
Min.
Max.
Min.
Max. Unit
WRITE CYCLE
tWC
tEW
tAW
tAS
Write Cycle Time
Chip Enable to End-of-Write(3)
15
12
12
0
—
—
—
—
—
—
—
10
—
10
—
—
—
17
12
12
0
—
—
—
—
—
—
—
10
—
10
—
—
—
20
15
15
0
—
—
—
—
—
—
—
12
—
12
—
—
—
25
20
20
0
—
—
—
—
—
—
—
15
—
15
—
—
—
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
Address Valid to End-of-Write
Address Set-up Time(3)
tWP
tWR
tDW
tHZ
Write Pulse Width
12
0
12
0
15
0
20
0
Write Recovery Time
Data Valid to End-of-Write
Output High-Z Time(1, 2)
Data Hold Time(4)
Write Enable to Output in High-Z(1, 2)
Output Active from End-of-Write(1, 2, 4)
SEM Flag Write to Read Time
SEM Flag Contention Window
10
—
0
10
—
0
15
—
0
15
—
0
tDH
tWZ
tOW
tSWRD
tSPS
—
0
—
0
—
0
—
0
5
5
5
5
5
5
5
5
IDT7005X35
IDT7005X55
IDT7005X70
Mil. Only
Symbol
Parameter
Min.
Max.
Min.
Max.
Min.
Max. Unit
WRITE CYCLE
tWC
tEW
Write Cycle Time
35
30
30
0
—
—
—
—
—
—
—
15
—
15
—
—
—
55
45
45
0
—
—
—
—
—
—
—
25
—
25
—
—
—
70
50
50
0
—
—
—
—
—
—
—
30
—
30
—
—
—
ns
ns
Chip Enable to End-of-Write(3)
Address Valid to End-of-Write
Address Set-up Time(3)
tAW
ns
tAS
ns
tWP
Write Pulse Width
25
0
40
0
50
0
ns
tWR
Write Recovery Time
ns
tDW
Data Valid to End-of-Write
Output High-Z Time(1, 2)
Data Hold Time(4)
Write Enable to Output in High-Z(1, 2)
Output Active from End-of-Write(1, 2, 4)
SEM Flag Write to Read Time
SEM Flag Contention Window
15
—
0
30
—
0
40
—
0
ns
tHZ
ns
tDH
ns
tWZ
—
0
—
0
—
0
ns
tOW
ns
tSWRD
tSPS
NOTES:
5
5
5
ns
5
5
5
ns
2738 tbl 14
1. Transition is measured ±500mV from Low or High-impedance voltage with the Output Test Load (Figure 2).
2. This parameter is guaranteed by device characterization but is not production tested.
3. To access RAM, CE = VIL, SEM = VIH. To access semaphore, CE = VIH and SEM = VIL. Either condition must be valid for the entire tEW time.
4. The specification for tDH must be met by the device supplying write data to the RAM under all operating conditions. Although tDH and tOW values will vary
over voltage and temperature, the actual tDH will always be smaller than the actual tOW.
5. "X" in part numbers indicates power rating (S or L).
6.06
9
IDT7005S/L
HIGH-SPEED 8K x 8 DUAL-PORT STATIC RAM
MILITARY AND COMMERCIAL TEMPERATURE RANGES
TIMING WAVEFORM OF WRITE CYCLE NO. 1, R/W CONTROLLED TIMING(1,5,8)
tWC
ADDRESS
(7)
tHZ
OE
t
AW
(9)
CE or SEM
(2)
tWP
(3)
(6)
tWR
tAS
R/W
DATAOUT
DATAIN
(7)
t
OW
tWZ
(4)
(4)
tDW
tDH
2738 drw 09
TIMING WAVEFORM OF WRITE CYCLE NO. 2, CE CONTROLLED TIMING(1,5)
t
WC
ADDRESS
CE or SEM (9)
R/W
tAW
(6)
AS
(3)
WR
(2)
tEW
t
t
tDW
tDH
DATAIN
2738 drw 10
NOTES:
1. R/W or CE must be high during all address transitions.
2. A write occurs during the overlap (tEW or tWP) of a Low CE and a Low R/W for memory array writing cycle.
3. tWR is measured from the earlier of CE or R/W (or SEM or R/W) going High to the end of write cycle.
4. During this period, the I/O pins are in the output state and input signals must not be applied.
5. If the CE or SEM Low transition occurs simultaneously with or after the R/W Low transition, the outputs remain in the High-impedance state.
6. Timing depends on which enable signal is asserted last, CE or R/W.
7. This parameter is guaranteed by device characterization, but is not production tested. Transition is measured +/- 500mv from steady state with the Output
Test Load (Figure 2).
8. If OE is Low during R/W controlled write cycle, the write pulse width must be the larger of tWP or (tWZ + tDW) to allow the I/O drivers to turn off and data
to be placed on the bus for the required tDW. If OE is High during an R/W controlled write cycle, this requirement does not apply and the write pulse can
be as short as the specified tWP.
9. To access RAM, CE = VIH and SEM = VIL. To access semaphore, CE = VIH and SEM = VIL. tEW must be met for either condition.
6.06
10
IDT7005S/L
HIGH-SPEED 8K x 8 DUAL-PORT STATIC RAM
MILITARY AND COMMERCIAL TEMPERATURE RANGES
TIMING WAVEFORM OF SEMAPHORE READ AFTER WRITE TIMING, EITHER SIDE(1)
t
OH
t
SAA
A0-A2
VALID ADDRESS
VALID ADDRESS
t
WR
t
ACE
t
AW
tEW
SEM
t
SOP
t
DW
DATAIN
VALID
DATAOUT
I/O
(2)
VALID
t
AS
t
WP
t
DH
R/W
t
SWRD
tAOE
OE
Write Cycle
Read Cycle
2738 drw 11
NOTES:
1. CE = VIH for the duration of the above timing (both write and read cycle).
2. "DATAOUT VALID" represents all I/O's (I/O0-I/O7) equal to the semaphore value.
TIMING WAVEFORM OF SEMAPHORE WRITE CONTENTION(1,3,4)
A
0"A"-A2"A"
MATCH
SIDE(2) “A”
R/W"A"
SEM"A"
tSPS
A
0"B"-A2"B"
MATCH
SIDE(2)
“B”
R/W"B"
SEM"B"
2738 drw 12
NOTES:
1. DOR = DOL = VIL, CER = CEL = VIH. Semaphore flag is released from both sides (reads as ones from both sides) at cycle start.
2. All timing is the same for left and right ports. Port “A” may be either left or right port. “B” is the opposite from port “A”.
3. This parameter is measured from R/W"A" or SEM"A" going High to R/W"B" or SEM"B" going High.
4. If tSPS is not satisfied, the semaphore will fall positively to one side or the other, but there is no guarantee which side will be granted the semaphore flag.
6.06
11
IDT7005S/L
HIGH-SPEED 8K x 8 DUAL-PORT STATIC RAM
MILITARY AND COMMERCIAL TEMPERATURE RANGES
AC ELECTRICAL CHARACTERISTICS OVER THE
OPERATING TEMPERATURE AND SUPPLY VOLTAGE RANGE(6)
IDT7005X15 IDT7005X17
Com'l. Only Com'l. Only
IDT7005X20
IDT7005X25
Symbol
Parameter
Min. Max. Min. Max.
Min.
Max.
Min.
Max. Unit
BUSY TIMING (M/S = VIH)
tBAA
tBDA
tBAC
tBDC
tAPS
tBDD
tWH
BUSY Access Time from Address Match
BUSY Disable Time from Address Not Matched
BUSY Access Time from Chip Enable Low
BUSY Disable Time from Chip Enable High
Arbitration Priority Set-up Time(2)
BUSY Disable to Valid Data(3)
Write Hold After BUSY(5)
—
—
—
—
5
15
15
15
15
—
18
—
—
—
—
—
5
17
17
17
17
—
18
—
—
—
—
—
5
20
20
20
17
—
30
—
—
—
—
—
5
20
20
20
17
—
30
—
ns
ns
ns
ns
ns
ns
ns
—
—
13
—
15
—
17
12
BUSY TIMING (M/S = VIL)
tWB
tWH
BUSY Input to Write(4)
Write Hold After BUSY(5)
0
—
—
0
—
—
0
—
—
0
—
—
ns
ns
12
13
15
17
PORT-TO-PORT DELAY TIMING
tWDD
tDDD
Write Pulse to Data Delay(1)
Write Data Valid to Read Data Delay(1)
—
—
30
25
—
—
30
25
—
—
45
35
—
—
50
35
ns
ns
IDT7005X35
IDT7005X55
IDT7005X70
Mil. Only
Symbol
Parameter
Min.
Max.
Min.
Max.
Min.
Max. Unit
BUSY TIMING (M/S = VIH)
tBAA
tBDA
tBAC
tBDC
tAPS
tBDD
BUSY Access Time from Address Match
—
—
—
—
5
20
20
20
20
—
35
—
—
—
—
5
45
40
40
35
—
40
—
—
—
—
5
45
40
40
35
—
45
ns
ns
ns
ns
ns
ns
BUSY Disable Time from Address Not Matched
BUSY Access Time from Chip Enable Low
BUSY Disable Time from Chip Enable High
Arbitration Priority Set-up Time(2)
BUSY Disable to Valid Data(3)
—
—
—
tWH
Write Hold After BUSY(5)
25
—
25
—
25
—
ns
BUSY TIMING (M/S = VIL)
tWB
tWH
BUSY Input to Write(4)
Write Hold After BUSY(5)
0
—
—
0
—
—
0
—
—
ns
ns
25
25
25
PORT-TO-PORT DELAY TIMING
tWDD
Write Pulse to Data Delay(1)
Write Data Valid to Read Data Delay(1)
—
—
60
45
—
—
80
65
—
—
95
80
ns
tDDD
ns
NOTES:
2738 tbl 15
1. Port-to-port delay through RAM cells from writing port to reading port, refer to "Timing Waveform of Write with Port-to-Port Read and BUSY".
2. To ensure that the earlier of the two ports wins.
3. tBDD is a calculated parameter and is the greater of 0, tWDD – tWP (actual), or tDDD – tDW (actual).
4. To ensure that the write cycle is inhibited on port "B" during contention with port "A".
5. To ensure that a write cycle is completed on port "B" after contention on port "A".
6. "X" in part numbers indicates power rating (S or L).
6.06
12
IDT7005S/L
HIGH-SPEED 8K x 8 DUAL-PORT STATIC RAM
MILITARY AND COMMERCIAL TEMPERATURE RANGES
(2,4,5)
TIMING WAVEFORM OF WRITE WITH PORT-TO-PORT READ WITH BUSY(M/S = VIH
)
tWC
MATCH
ADDR"A"
R/W"A"
t
WP
t
DW
t
DH
VALID
DATAIN "A"
(1)
t
APS
MATCH
ADDR"B"
tBDA
tBDD
BUSY"B"
t
WDD
DATAOUT "B"
VALID
(3)
tDDD
2738 drw 13
NOTES:
1. To ensure that the earlier of the two ports wins. tAPS is ignored for for M/S = VIL (slave).
2. CEL = CER = VIL.
3. OE = VIL for the reading port.
4. If M/S = VIL (slave), BUSY is an input. Then for this example BUSY"A" = VIH and BUSY"B" input is shown above.
5. All timing is the same for left and right ports. Port "A" may be either the left or right port. Port "B" is the port opposite port "A".
TIMING WAVEFORM OF WITH WRITE BUSY
tWP
R/W"A"
(3)
tWB
BUSY"B"
(1)
t
WH
(2)
R/W"B"
2738 drw 14
NOTES:
1. tWH must be met for both BUSY input (slave) and output (master).
2. BUSY is asserted on Port "B" Blocking R/W"B", until BUSY"B" goes High.
3. tWB is only for the 'Slave' Version.
6.06
13
IDT7005S/L
HIGH-SPEED 8K x 8 DUAL-PORT STATIC RAM
MILITARY AND COMMERCIAL TEMPERATURE RANGES
WAVEFORM OF BUSY ARBITRATION CONTROLLED BY CE TIMING (M/S = VIH)(1)
ADDR"A"
and "B"
ADDRESSES MATCH
CE"A"
(2)
tAPS
CE"B"
tBAC
tBDC
BUSY"B"
2738 drw 15
WAVEFORM OF BUSY ARBITRATION CYCLE CONTROLLED BY ADDRESS MATCH TIMING
(M/S = VIH)(1)
ADDRESS "N"
ADDR"A"
ADDR"B"
BUSY"B"
(2)
tAPS
MATCHING ADDRESS "N"
t
BAA
tBDA
2738 drw 16
NOTES:
1. All timing is the same for left and right ports. Port “A” may be either the left or right port. Port “B” is the port opposite from port “A”.
2. If tAPS is not satisfied, the busy signal will be asserted on one side or another but there is no guarantee on which side busy will be asserted.
AC ELECTRICAL CHARACTERISTICS OVER THE
OPERATING TEMPERATURE AND SUPPLY VOLTAGE RANGE(1)
IDT7005X15
Com'l. Only
IDT7005X17
Com'l. Only
IDT7005X20
IDT7005X25
Symbol
Parameter
Min.
Max.
Min.
Max.
Min.
Max.
Min.
Max. Unit
INTERRUPT TIMING
tAS
Address Set-up Time
0
0
0
0
—
—
15
15
0
0
—
—
15
15
0
0
—
—
20
20
0
0
—
—
20
20
ns
ns
ns
ns
tWR
tINS
tINR
Write Recovery Time
Interrupt Set Time
—
—
—
—
—
—
Interrupt Reset Time
IDT7005X35
IDT7005X55
IDT7005X70
Mil. Only
Symbol
Parameter
Min.
Max.
Min.
Max.
Min.
Max. Unit
INTERRUPT TIMING
tAS
Address Set-up Time
0
0
—
—
25
25
0
0
—
—
40
40
0
0
—
—
50
50
ns
ns
ns
ns
tWR
tINS
tINR
Write Recovery Time
Interrupt Set Time
—
—
—
—
—
—
Interrupt Reset Time
NOTE:
2738 tbl 16
1. "X" in part numbers indicates power rating (S or L).
6.06
14
IDT7005S/L
HIGH-SPEED 8K x 8 DUAL-PORT STATIC RAM
MILITARY AND COMMERCIAL TEMPERATURE RANGES
WAVEFORM OF INTERRUPT TIMING(1)
t
WC
INTERRUPT SET ADDRESS(2)
ADDR"A"
CE"A"
(3)
(4)
t
AS
tWR
R/W"A"
INT"B"
(3)
t
INS
2738 drw 17
tRC
INTERRUPT CLEAR ADDRESS(2)
ADDR"B"
CE"B"
(3)
t
AS
OE"B"
(3)
t
INR
INT"B"
2738 drw 18
NOTES:
1. All timing is the same for left and right ports. Port “A” may be either the left or right port. Port “B” is the port opposite from port “A”.
2. See Interrupt truth table.
3. Timing depends on which enable signal (CE or R/W) asserted last.
4. Timing depends on which enable signal (CE or R/W) is de-asserted first.
TRUTH TABLES
TRUTH TABLE I — INTERRUPT FLAG(1,4)
Left Port
Right Port
OER A12R-A0R INTR
R/WL
CEL
L
OEL A12L-A0L INTL
R/WR
CER
X
Function
Set Right INTR Flag
L
X
X
X
L
1FFF
X
X
X
L(3)
H(2)
X
X
L
X
L
X
L(2)
H(3)
X
X
X
L
1FFF
1FFE
X
Reset Right INTR Flag
Set Left INTL Flag
X
X
X
X
L
X
X
L
1FFE
X
X
X
Reset Left INTL Flag
NOTES:
2738 tbl 17
1. Assumes BUSYL = BUSYR = VIH.
2. If BUSYL = VIL, then no change.
3. If BUSYR = VIL, then no change.
4. INTR and INTL must be initialized at power-up.
6.06
15
IDT7005S/L
HIGH-SPEED 8K x 8 DUAL-PORT STATIC RAM
MILITARY AND COMMERCIAL TEMPERATURE RANGES
TRUTH TABLE II —
ADDRESS BUSY ARBITRATION
Inputs
Outputs
A0L-A12L
CER A0R-A12R BUSYL
(1)
(1)
CEL
X
BUSYR
Function
Normal
X
X
H
L
NO MATCH
MATCH
H
H
H
H
H
Normal
X
MATCH
H
H
Normal
Write Inhibit(3)
L
MATCH
(2)
(2)
NOTES:
2738 tbl 18
1. Pins BUSYL and BUSYR are both outputs when the part is configured as a master. Both are inputs when configured as a slave. BUSYX outputs on the
IDT7005 are push-pull, not open drain outputs. On slaves the BUSYX input internally inhibits writes.
2. 'L' if the inputs to the opposite port were stable prior to the address and enable inputs of this port. 'H' if the inputs to the opposite port became stable after
the address and enable inputs of this port. If tAPS is not met, either BUSYL or BUSYR = Low will result. BUSYL and BUSYR outputs can not be low
simultaneously.
3. Writes to the left port are internally ignored when BUSYL outputs are driving low regardless of actual logic level on the pin. Writes to the right port are
internally ignored when BUSYR outputs are driving low regardless of actual logic level on the pin.
TRUTH TABLE III — EXAMPLE OF SEMAPHORE PROCUREMENT SEQUENCE(1,2)
Functions
D0 - D7 Left
D0 - D7 Right
Status
No Action
1
0
0
1
1
0
1
1
1
0
1
1
1
1
0
0
1
1
0
1
1
1
Semaphore free
Left Port Writes "0" to Semaphore
Right Port Writes "0" to Semaphore
Left Port Writes "1" to Semaphore
Left Port Writes "0" to Semaphore
Right Port Writes "1" to Semaphore
Left Port Writes "1" to Semaphore
Right Port Writes "0" to Semaphore
Right Port Writes "1" to Semaphore
Left Port Writes "0" to Semaphore
Left Port Writes "1" to Semaphore
Left port has semaphore token
No change. Right side has no write access to semaphore
Right port obtains semaphore token
No change. Left port has no write access to semaphore
Left port obtains semaphore token
Semaphore free
Right port has semaphore token
Semaphore free
Left port has semaphore token
Semaphore free
NOTES:
2738 tbl 19
1. This table denotes a sequence of events for only one of the eight semaphores on the IDT7005.
2. There are eight semaphore flags written to via I/O0 and read from all I/O's (I/O0-I/O7). These eight semaphores are addressed by A0 - A2.
FUNCTIONAL DESCRIPTION
theleftportwritestomemorylocation1FFF(HEX)andtoclear
the interrupt flag (INTR), the right port must read the memory
location 1FFF. The message (8 bits) at 1FFE or 1FFF is user-
defined, since it is an addressable SRAM location. If the
interrupt function is not used, address locations 1FFE and
1FFF are not used as mail boxes, but as part of the random
access memory. Refer to Truth Table for the interrupt opera-
tion.
The IDT7005 provides two ports with separate control,
addressandI/Opinsthatpermitindependentaccessforreads
or writes to any location in memory. The IDT7005 has an
automatic power down feature controlled by CE. The CE
controls on-chip power down circuitry that permits the respec-
tive port to go into a standby mode when not selected (CE
high). When a port is enabled, access to the entire memory
array is permitted.
BUSY LOGIC
INTERRUPTS
Busy Logic provides a hardware indication that both ports
of the RAM have accessed the same location at the same
time. It also allows one of the two accesses to proceed and
signalstheothersidethattheRAMis“Busy”. Thebusypincan
thenbeusedtostalltheaccessuntiltheoperationon theother
side is completed. If a write operation has been attempted
from the side that receives a busy indication, the write signal
is gated internally to prevent the write from proceeding.
If the user chooses to use the interrupt function, a memory
location(mailboxormessagecenter)isassignedtoeachport.
Theleftportinterruptflag(INTL)isassertedwhentherightport
writes to memory location 1FFE (HEX), where a write is
defined as CE = R/W= VIL per the Truth Table . The left port
clears the interrupt through access of address location 1FFE
when CE = OE = VIL. For this example, R/W is a "don't care".
Likewise, the right port interrupt flag (INTR) is asserted when
6.06
16
IDT7005S/L
HIGH-SPEED 8K x 8 DUAL-PORT STATIC RAM
MILITARY AND COMMERCIAL TEMPERATURE RANGES
MASTER
CE
SLAVE
CE
Dual Port
RAM
Dual Port
RAM
BUSY
R
BUSY
L
BUSY
L
BUSYR
MASTER
Dual Port
RAM
SLAVE
Dual Port
RAM
CE
CE
BUSY
BUSY
R
BUSY
L
BUSYL
BUSY
R
R
BUSY
L
2738 drw 19
Figure 3. Busy and chip enable routing for both width and depth expansion with IDT7005 RAMs.
output from the master before the actual write pulse can be
The use of busy logic is not required or desirable for all initiatedwiththeR/Wsignal. Failuretoobservethistimingcan
applications. In some cases it may be useful to logically OR result in a glitched internal write inhibit signal and corrupted
the busy outputs together and use any busy indication as an data in the slave.
interrupt source to flag the event of an illegal or illogical
operation. If the write inhibit function of busy logic is not
desirable, the busy logic can be disabled by placing the part
in slave mode with the M/Spin. Once in slave mode theBUSY
pin operates solely as a write inhibit input pin. Normal opera-
tion can be programmed by tying the BUSY pins high. If
desired, unintended write operations can be prevented to a
port by tying the busy pin for that port low.
SEMAPHORES
The IDT7005 is an extremely fast Dual-Port 8K x 8 CMOS
Static RAM with an additional 8 address locations dedicated
tobinarysemaphoreflags. Theseflagsalloweitherprocessor
on the left or right side of the Dual-Port RAM to claim a
privilege over the other processor for functions defined by the
system designer’s software. As an example, the semaphore
The busy outputs on the IDT 7005 RAM in master mode,
can be used by one processor to inhibit the other from
are push-pull type outputs and do not require pull up resistors
accessing a portion of the Dual-Port RAM or any other shared
to operate. If these RAMs are being expanded in depth, then
resource.
the busy indication for the resulting array requires the use of
The Dual-Port RAM features a fast access time, and both
ports are completely independent of each other. This means
an external AND gate.
that the activity on the left port in no way slows the access time
oftherightport. Bothportsareidenticalinfunctiontostandard
CMOS Static RAM and can be read from, or written to, at the
WIDTH EXPANSION WITH BUSY LOGIC
MASTER/SLAVE ARRAYS
When expanding an IDT7005 RAM array in width while same time with the only possible conflict arising from the
using busy logic, one master part is used to decide which side simultaneous writing of, or a simultaneous READ/WRITE of,
of the RAM array will receive a busy indication, and to output anon-semaphorelocation. Semaphoresareprotectedagainst
that indication. Any number of slaves to be addressed in the such ambiguous situations and may be used by the system
same address range as the master, use the busy signal as a program to avoid any conflicts in the non-semaphore portion
write inhibit signal. Thus on the IDT7005 RAM the busy pin is of the Dual-Port RAM. These devices have an automatic
an output if the part is used as a master (M/Spin = H), and the power-down feature controlled by CE, the Dual-Port RAM
busy pin is an input if the part used as a slave (M/Spin = L) as enable, and SEM, the semaphore enable. The CE and SEM
shown in Figure 3.
pins control on-chip power down circuitry that permits the
If two or more master parts were used when expanding in respective port to go into standby mode when not selected.
width, a split decision could result with one master indicating This is the condition which is shown in Truth Table where CE
busy on one side of the array and another master indicating and SEM are both high.
busyononeothersideofthearray. Thiswouldinhibitthewrite
Systems which can best use the IDT7005 contain multiple
operations from one port for part of a word and inhibit the write processors or controllers and are typically very high-speed
operations from the other port for the other part of the word. systems which are software controlled or software intensive.
The busy arbitration, on a master, is based on the chip These systems can benefit from a performance increase
enableandaddresssignalsonly.Itignoreswhetheranaccess offered by the IDT7005's hardware semaphores, which pro-
is a read or write. In a master/slave array, both address and vide a lockout mechanism without requiring complex pro-
chip enable must be valid long enough for a busy flag to be gramming.
6.06
17
IDT7005S/L
HIGH-SPEED 8K x 8 DUAL-PORT STATIC RAM
MILITARY AND COMMERCIAL TEMPERATURE RANGES
Software handshaking between processors offers the until the semaphore is freed by the first side.
maximum in system flexibility by permitting shared resources
When a semaphore flag is read, its value is spread into all
to be allocated in varying configurations. The IDT7005 does data bits so that a flag that is a one reads as a one in all data
not use its semaphore flags to control any resources through bits and a flag containing a zero reads as all zeros. The read
hardware, thus allowing the system designer total flexibility in valueislatchedintooneside’soutputregisterwhenthatside's
system architecture.
semaphore select (SEM) and output enable (OE) signals go
An advantage of using semaphores rather than the more active. This serves to disallow the semaphore from changing
common methods of hardware arbitration is that wait states state in the middle of a read cycle due to a write cycle from the
are never incurred in either processor. This can prove to be other side. Because of this latch, a repeated read of a
a major advantage in very high-speed systems.
semaphoreinatestloopmustcauseeithersignal(SEMorOE)
to go inactive or the output will never change.
A sequence WRITE/READ must be used by the sema-
phore in order to guarantee that no system level contention
will occur. A processor requests access to shared resources
by attempting to write a zero into a semaphore location. If the
semaphore is already in use, the semaphore request latch will
contain a zero, yet the semaphore flag will appear as one, a
fact which the processor will verify by the subsequent read
(see Table III). As an example, assume a processor writes a
zero to the left port at a free semaphore location. On a
subsequent read, the processor will verify that it has written
successfully to that location and will assume control over the
resource in question. Meanwhile, if a processor on the right
side attempts to write a zero to the same semaphore flag it will
fail, as will be verified by the fact that a one will be read from
that semaphore on the right side during subsequent read.
Had a sequence of READ/WRITE been used instead, system
contention problems could have occurred during the gap
between the read and write cycles.
It is important to note that a failed semaphore request must
be followed by either repeated reads or by writing a one into
the same location. The reason for this is easily understood by
looking at the simple logic diagram of the semaphore flag in
Figure 4. Two semaphore request latches feed into a sema-
phore flag. Whichever latch is first to present a zero to the
semaphore flag will force its side of the semaphore flag low
andtheothersidehigh. Thisconditionwillcontinueuntilaone
is written to the same semaphore request latch. Should the
other side’s semaphore request latch have been written to a
zero in the meantime, the semaphore flag will flip over to the
other side as soon as a one is written into the first side’s
request latch. The second side’s flag will now stay low until its
semaphore request latch is written to a one. From this it is
easy to understand that, if a semaphore is requested and the
processor which requested it no longer needs the resource,
the entire system can hang up until a one is written into that
semaphore request latch.
HOW THE SEMAPHORE FLAGS WORK
The semaphore logic is a set of eight latches which are
independent of the Dual-Port RAM. These latches can be
used to pass a flag, or token, from one port to the other to
indicate that a shared resource is in use. The semaphores
provideahardwareassistforauseassignmentmethodcalled
“Token Passing Allocation.” In this method, the state of a
semaphore latch is used as a token indicating that shared
resource is in use. If the left processor wants to use this
resource, it requests the token by setting the latch. This
processor then verifies its success in setting the latch by
reading it. If it was successful, it proceeds to assume control
overthesharedresource. Ifitwasnotsuccessfulinsettingthe
latch, it determines that the right side processor has set the
latchfirst, hasthetokenandisusingthesharedresource. The
left processor can then either repeatedly request that
semaphore’s status or remove its request for that semaphore
to perform another task and occasionally attempt again to
gain control of the token via the set and test sequence. Once
the right side has relinquished the token, the left side should
succeed in gaining control.
The semaphore flags are active low. A token is requested
by writing a zero into a semaphore latch and is released when
the same side writes a one to that latch.
The eight semaphore flags reside within the IDT7005 in a
separate memory space from the Dual-Port RAM. This
address space is accessed by placing a low input on the SEM
pin (which acts as a chip select for the semaphore flags) and
using the other control pins (Address, OE, and R/W) as they
would be used in accessing a standard static RAM. Each of
the flags has a unique address which can be accessed by
eithersidethroughaddresspinsA0–A2. Whenaccessingthe
semaphores, none of the other address pins has any effect.
When writing to a semaphore, only data pin D0 is used. If
a low level is written into an unused semaphore location, that
flagwillbesettoazeroonthatsideandaoneontheotherside
(see Table III). That semaphore can now only be modified by
thesideshowingthezero. Whenaoneiswrittenintothesame
locationfromthesameside,theflagwillbesettoaoneforboth
sides (unless a semaphore request from the other side is
pending) and then can be written to by both sides. The fact
that the side which is able to write a zero into a semaphore
subsequently locks out writes from the other side is what
makes semaphore flags useful in interprocessor communica-
tions. (Athoroughdiscussingontheuseofthisfeaturefollows
shortly.) A zero written into the same location from the other
side will be stored in the semaphore request latch for that side
The critical case of semaphore timing is when both sides
request a single token by attempting to write a zero into it at
the same time. The semaphore logic is specially designed to
resolve this problem. If simultaneous requests are made, the
logic guarantees that only one side receives the token. If one
side is earlier than the other in making the request, the first
side to make the request will receive the token. If both
requests arrive at the same time, the assignment will be
arbitrarily made to one port or the other.
One caution that should be noted when using semaphores
is that semaphores alone do not guarantee that access to a
6.06
18
IDT7005S/L
HIGH-SPEED 8K x 8 DUAL-PORT STATIC RAM
MILITARY AND COMMERCIAL TEMPERATURE RANGES
resource is secure. As with any powerful programming side, the left side could undo its semaphore request and
technique, if semaphores are misused or misinterpreted, a perform other tasks until it was able to write, then read a zero
software error can easily happen.
into Semaphore 1. If the right processor performs a similar
Initialization of the semaphores is not automatic and must task with Semaphore 0, this protocol would allow the two
be handled via the initialization program at power-up. Since processors to swap 4K blocks of Dual-Port RAM with each
any semaphore request flag which contains a zero must be other.
reset to a one, all semaphores on both sides should have a
The blocks do not have to be any particular size and can
one written into them at initialization from both sides to assure even be variable, depending upon the complexity of the
that they will be free when needed.
software using the semaphore flags. All eight semaphores
could be used to divide the Dual-Port RAM or other shared
resources into eight parts. Semaphores can even be as-
signed different meanings on different sides rather than being
given a common meaning as was shown in the example
above.
Semaphores are a useful form of arbitration in systems like
disk interfaces where the CPU must be locked out of a section
ofmemoryduringatransferandtheI/Odevicecannottolerate
any wait states. With the use of semaphores, once the two
deviceshasdeterminedwhichmemoryareawas“off-limits”to
the CPU, both the CPU and the I/O devices could access their
assigned portions of memory continuously without any wait
states.
Semaphores are also useful in applications where no
memory “WAIT” state is available on one or both sides. Once
a semaphore handshake has been performed, both proces-
sors can access their assigned RAM segments at full speed.
Another application is in the area of complex data struc-
tures. In this case, block arbitration is very important. For this
applicationoneprocessormayberesponsibleforbuildingand
updating a data structure. The other processor then reads
andinterpretsthatdatastructure. Iftheinterpretingprocessor
reads an incomplete data structure, a major error condition
may exist. Therefore, some sort of arbitration must be used
between the two different processors. The building processor
arbitrates for the block, locks it and then is able to go in and
update the data structure. When the update is completed, the
data structure block is released. This allows the interpreting
processortocomebackandreadthecompletedatastructure,
thereby guaranteeing a consistent data structure.
USING SEMAPHORES—SOME EXAMPLES
Perhaps the simplest application of semaphores is their
application as resource markers for the IDT7005’s Dual-Port
RAM. Say the 8K x 8 RAM was to be divided into two 4K x 8
blockswhichweretobededicatedatanyonetimetoservicing
either the left or right port. Semaphore 0 could be used to
indicate the side which would control the lower section of
memory, and Semaphore 1 could be defined as the indicator
for the upper section of memory.
To take a resource, in this example the lower 4K of
Dual-Port RAM, the processor on the left port could write and
then read a zero in to Semaphore 0. If this task were
successfully completed (a zero was read back rather than a
one), the left processor would assume control of the lower 4K.
Meanwhile the right processor was attempting to gain control
of the resource after the left processor, it would read back a
one in response to the zero it had attempted to write into
Semaphore 0. At this point, the software could choose to try
and gain control of the second 4K section by writing, then
reading a zero into Semaphore 1. If it succeeded in gaining
control, it would lock out the left side.
Once the left side was finished with its task, it would write
a one to Semaphore 0 and may then try to gain access to
Semaphore 1. If Semaphore 1 was still occupied by the right
L PORT
R PORT
SEMAPHORE
REQUEST FLIP FLOP
SEMAPHORE
REQUEST FLIP FLOP
D0
D0
D
D
Q
Q
WRITE
WRITE
SEMAPHORE
READ
SEMAPHORE
READ
2738 drw 20
Figure 4. IDT7005 Semaphore Logic
6.06
19
IDT7005S/L
HIGH-SPEED 8K x 8 DUAL-PORT STATIC RAM
MILITARY AND COMMERCIAL TEMPERATURE RANGES
ORDERING INFORMATION
IDT XXXXX
A
999
A
A
Device
Type
Power
Speed
Package
Process/
Temperature
Range
Blank
Commercial (0°C to +70°C)
B
Military (–55°C to +125°C)
Compliant to MIL-STD-883, Class B
PF
G
J
64-pin TQFP (PN64-1)
68-pin PGA (G68-1)
68-pin PLCC (J68-1)
68-pin Flatpack (F64-1)
F
15
17
20
25
35
55
70
Commercial Only
Commercial Only
Speed in nanoseconds
Military Only
S
L
Standard Power
Low Power
7005 64K (8K x 8) Dual-Port RAM
2738 drw 21
6.06
20
相关型号:
IDT7005L35GGI
Dual-Port SRAM, 8KX8, 35ns, CMOS, CPGA68, 1.180 X 1.180 INCH, 0.160 INCH HEIGHT, GREEN, CERAMIC, PGA-68
IDT
IDT7005L35GI
Dual-Port SRAM, 8KX8, 35ns, CMOS, CPGA68, 1.180 X 1.180 INCH, 0.160 INCH HEIGHT, CERAMIC, PGA-68
IDT
IDT7005L35J8
Dual-Port SRAM, 8KX8, 35ns, CMOS, PQCC68, 0.950 X 0.950 INCH, 0.120 INCH HEIGHT, PLASTIC, LCC-68
IDT
IDT7005L35JG
Dual-Port SRAM, 8KX8, 35ns, CMOS, PQCC68, 0.950 X 0.950 INCH, 0.120 INCH HEIGHT, GREEN, PLASTIC, LCC-68
IDT
IDT7005L35JGI
Dual-Port SRAM, 8KX8, 35ns, CMOS, PQCC68, 0.950 X 0.950 INCH, 0.120 INCH HEIGHT, GREEN, PLASTIC, LCC-68
IDT
IDT7005L35JI
Dual-Port SRAM, 8KX8, 35ns, CMOS, PQCC68, 0.950 X 0.950 INCH, 0.120 INCH HEIGHT, PLASTIC, LCC-68
IDT
©2020 ICPDF网 联系我们和版权申明