IDT5V991A-7JI [IDT]
3.3V PROGRAMMABLE SKEW PLL CLOCK DRIVER TURBOCLOCK; 3.3V的可编程相偏PLL时钟驱动器TURBOCLOCK型号: | IDT5V991A-7JI |
厂家: | INTEGRATED DEVICE TECHNOLOGY |
描述: | 3.3V PROGRAMMABLE SKEW PLL CLOCK DRIVER TURBOCLOCK |
文件: | 总8页 (文件大小:79K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
IDT5V991A
3.3V PROGRAMMABLE
SKEW PLL CLOCK DRIVER
TURBOCLOCK™
FEATURES:
DESCRIPTION:
• REF is 5V tolerant
The IDT5V991Ais a highfanout3.3VPLLbasedclockdriverintended
forhighperformancecomputinganddata-communicationsapplications.A
keyfeatureoftheprogrammableskewistheabilityofoutputstoleadorlag
the REF input signal. The IDT5V991A has eight programmable skew
outputs infourbanks of2.Skewis controlledby3-levelinputsignals that
may be hard-wired to appropriate HIGH-MID-LOW levels.
• 4 pairs of programmable skew outputs
• Low skew: 200ps same pair, 250ps all outputs
• Selectable positive or negative edge synchronization:
Excellent for DSP applications
• Synchronous output enable
• Output frequency: 3.75MHz to 85MHz
• 2x, 4x, 1/2, and 1/4 outputs
Whenthe GND/sOE pinis heldlow,allthe outputs are synchronously
enabled.However,ifGND/sOEisheldhigh,alltheoutputsexcept3Q0and
3Q1 are synchronously disabled.
• 3 skew grades:
IDT5V991A-2: tSKEW0<250ps
IDT5V991A-5: tSKEW0<500ps
IDT5V991A-7: tSKEW0<750ps
• 3-level inputs for skew and PLL range control
• PLL bypass for DC testing
Furthermore, when the VCCQ/PE is held high, all the outputs are
synchronizedwiththe positive edge ofthe REFclockinput.WhenVCCQ/
PEis heldlow,allthe outputs are synchronizedwiththe negative edge of
REF. BothdeviceshaveLVTTLoutputswith12mAbalanceddriveoutputs.
• External feedback, internal loop filter
• 12mA balanced drive outputs
• Low Jitter: <200ps peak-to-peak
• Available in 32-pin PLCC Package
FUNCTIONALBLOCKDIAGRAM
GND/sOE
1Q0
Skew
Select
1Q1
3
3
1F1:0
2F1:0
3F1:0
4F1:0
VCCQ/PE
2Q0
2Q1
Skew
Select
3
3
3
3
REF
PLL
FB
3Q0
3Q1
Skew
Select
3
3
FS
4Q0
4Q1
Skew
Select
3
TheIDTlogoisaregisteredtrademarkofIntegratedDeviceTechnology,Inc.
COMMERCIAL AND INDUSTRIAL TEMPERATURE RANGES
SEPTEMBER 2001
1
c
2001 Integrated Device Technology, Inc.
DSC 5963/3
IDT5V991A
3.3VPROGRAMMABLESKEWPLLCLOCKDRIVERTURBOCLOCK
COMMERCIALANDINDUSTRIALTEMPERATURERANGES
PINCONFIGURATION
ABSOLUTEMAXIMUMRATINGS(1)
Symbol
Description
Supply Voltage to Ground
DC Input Voltage
Max
–0.5 to +7
–0.5 to VCC+0.5
–0.5 to +5.5
150
Unit
V
VI
V
REF Input Voltage
V
4
3
2
1
32 31 30
TJ
Junction Temperature
Storage Temperature
° C
° C
3F1
4F0
5
29
28
27
26
25
24
23
22
21
2F0
TSTG
–65 to +150
6
GND/sOE
1F1
4F1
7
NOTE:
1. Stresses beyond those listed under ABSOLUTE MAXIMUM RATINGS may cause
permanent damage to the device. These are stress ratings only, and functional
operation of the device at these or any other conditions above those indicated in the
operational sections of this specification is not implied. Exposure to absolute-
maximum-rated conditions for extended periods may affect device reliability.
VCCQ/PE
8
1F0
VCCN
VCCN
4Q1
9
10
11
12
13
1Q0
4Q0
1Q1
GND
GND
GND
GND
14 15 16 17 18 19 20
CAPACITANCE(TA = +25°C, f = 1MHz, VIN = 0V)
Parameter Description
Typ. Max.
Unit
CIN
InputCapacitance
5
7
pF
PLCC
TOP VIEW
NOTE:
1. Capacitance applies to all inputs except TEST, FS, and nF1:0.
PINDESCRIPTION
Pin Name
REF
Type
IN
Description
ReferenceClockInput
FeedbackInput
FB
IN
TEST(1)
IN
When MID or HIGH, disables PLL (except for conditions of Note 1). REF goes to all outputs. Skew selections (see Control
SummaryTable)remainineffect. SetLOWfornormaloperation.
GND/ sOE (1)
IN
IN
Synchronous Output Enable. When HIGH, it stops clock outputs (except 3Q0 and 3Q1) in a LOW state - 3Q0 and 3Q1 may be used
as the feedback signal to maintain phase lock. When TEST is held at MID level and GND/sOE is HIGH, the nF[1:0] pins act as
output disable controls for individual banks when nF[1:0] =LL. SetGND/sOELOWfornormaloperation.
Selectablepositiveornegativeedgecontrol. WhenLOW/HIGHtheoutputsaresynchronizedwiththenegative/positiveedgeofthe
referenceclock.
VCCQ/PE
nF[1:0]
FS
IN
3-levelinputsforselecting1of9skewtapsorfrequencyfunctions
IN
Selectsappropriateoscillatorcircuitbasedonanticipatedfrequencyrange. (SeePLLProgrammableSkewRange.)
Fourbanksoftwooutputswithprogrammableskew
nQ[1:0]
VCCN
VCCQ
GND
OUT
PWR
PWR
PWR
Powersupplyforoutputbuffers
Powersupplyforphaselockedloopandotherinternalcircuitry
Ground
NOTE:
1.When TEST = MID and GND/sOE = HIGH, PLL remains active with nF[1:0] = LL functioning as an output disable control for individual output banks. Skew selections remain
in effect unless nF[1:0] = LL.
PROGRAMMABLESKEW
Output skew with respect to the REF input is adjustable to compensate to minimize the number of control pins, 3-level inputs (HIGH-MID-LOW)
for PCB trace delays, backplane propagation delays or to accommodate are used, they are intended for but not restricted to hard-wiring. Undriven
requirements for special timing relationships between clocked compo- 3-level inputs default to the MID level. Where programmable skew is
nents. Skew is selectable as a multiple of a time unit tU which is of the not a requirement, the control pins can be left open for the zero skew
order of a nanosecond (see PLL Programmable Skew Range and Resolution default setting. The Control Summary Table shows how to select specific
Table). There are nine skew configurations available for each output skew taps by using the nF1:0 control pins.
pair. These configurations are chosen by the nF1:0 control pins. In order
2
IDT5V991A
COMMERCIALANDINDUSTRIALTEMPERATURERANGES
3.3VPROGRAMMABLESKEWPLLCLOCKDRIVERTURBOCLOCK
EXTERNALFEEDBACK
By providing external feedback, the IDT5V991A gives users flexibility
with regard to skew adjustment. The FB signal is compared with the
input REF signal at the phase detector in order to drive the VCO. Phase
differences cause the VCO of the PLL to adjust upwards or downwards
accordingly.
An internal loop filter moderates the response of the VCO to the
phase detector. The loop filter transfer function has been chosen to
provide minimal jitter (or frequency variation) while still providing accu-
rate responses to input frequency changes.
PLLPROGRAMMABLESKEWRANGEANDRESOLUTIONTABLE
FS = LOW
1/(44 x FNOM)
15 to 35MHz
FS = MID
1/(26 x FNOM)
25 to 60MHz
FS = HIGH
1/(16 x FNOM)
40 to 85 MHz
Comments
TimingUnitCalculation(tU)
VCOFrequencyRange(FNOM)(1,2)
SkewAdjustmentRange(3)
MaxAdjustment:
±9.09ns
±49º
±9.23ns
±83º
±9.38ns
±135º
ns
PhaseDegrees
% of Cycle Time
±14%
tU =1.52ns
tU =0.91ns
tU =0.76ns
—
±23%
±37%
—
Example 1, FNOM = 15MHz
Example 2, FNOM = 25MHz
Example 3, FNOM = 30MHz
Example 4, FNOM = 40MHz
Example 5, FNOM = 50MHz
Example 6, FNOM = 80MHz
—
tU =1.54ns
tU =1.28ns
tU =0.96ns
tU =0.77ns
—
—
—
tU =1.56ns
tU =1.25ns
tU =0.78ns
—
—
NOTES:
1. The device may be operated outside recommended frequency ranges without damage, but functional operation is not guaranteed. Selecting the appropriate FS value based on
input frequency range allows the PLL to operate in its ‘sweet spot’ where jitter is lowest.
2. The level to be set on FS is determined by the nominal operating frequency of the VCO and Time Unit Generator. The VCO frequency always appears at 1Q1:0, 2Q1:0, and the
higher outputs when they are operated in their undivided modes. The frequency appearing at the REF and FB inputs will be the same as the VCO when the output connected
to FB is undivided. The frequency of the REF and FB inputs will be 1/2 or 1/4 the VCO frequency when the part is configured for a frequency multiplication by using a divided
output as the FB input.
3. Skew adjustment range assumes that a zero skew output is used for feedback. If a skewed Q output is used for feedback, then adjustment range will be greater. For example
if a 4tU skewed output is used for feedback, all other outputs will be skewed –4tU in addition to whatever skew value is programmed for those outputs. ‘Max adjustment’ range
applies to output pairs 3 and 4 where ± 6tU skew adjustment is possible and at the lowest FNOM value.
CONTROLSUMMARYTABLEFORFEEDBACKSIGNALS
nF1:0
Skew (Pair #1, #2)
Skew (Pair #3)
Divide by 2
–6tU
Skew (Pair #4)
Divide by 2
–6tU
(1)
LL
–4tU
–3tU
LM
LH
–2tU
–4tU
–4tU
ML
–1tU
–2tU
–2tU
MM
MH
HL
ZeroSkew
1tU
ZeroSkew
2tU
ZeroSkew
2tU
2tU
4tU
4tU
HM
HH
3tU
6tU
6tU
Inverted(2)
4tU
Divide by 4
NOTES:
1. LL disables outputs if TEST = MID and GND/sOE = HIGH.
2. When pair #4 is set to HH (inverted), GND/sOE disables pair #4 HIGH when VCCQ/PE = HIGH, GND/sOE disables pair #4 LOW when VCCQ/PE = LOW.
3
IDT5V991A
3.3VPROGRAMMABLESKEWPLLCLOCKDRIVERTURBOCLOCK
COMMERCIALANDINDUSTRIALTEMPERATURERANGES
RECOMMENDEDOPERATINGRANGE
IDT5V991A-2, -5, -7
(Industrial)
IDT5V991A-2
(Commercial)
Symbol
Vcc
Description
Min.
3
Max.
Min.
Max.
3.6
Unit
V
Power Supply Voltage
AmbientOperatingTemperature
3.6
3
0
TA
-40
+85
+70
° C
DC ELECTRICAL CHARACTERISTICS OVER OPERATING RANGE
Symbol
Parameter
Conditions
Guaranteed Logic HIGH (REF, FB Inputs Only)
Guaranteed Logic LOW (REF, FB Inputs Only)
3-Level Inputs Only
Min.
Max.
—
Unit
V
VIH
Input HIGH Voltage
2
—
VIL
InputLOWVoltage
0.8
V
VIHH
VIMM
VILL
IIN
Input HIGH Voltage(1)
InputMIDVoltage(1)
InputLOWVoltage(1)
InputLeakageCurrent
(REF, FB Inputs Only)
VCC−0.6
VCC/2−0.3
—
—
V
3-Level Inputs Only
VCC/2+0.3
0.6
V
3-Level Inputs Only
V
VIN = VCC or GND
—
±5
µ A
VCC = Max.
VIN = VCC
HIGH Level
MID Level
LOW Level
—
—
—
—
—
2.4
—
±200
±50
I3
3-Level Input DC Current (TEST, FS, nF1:0)
VIN = VCC/2
µ A
VIN = GND
±200
±100
±100
—
IPU
IPD
InputPull-UpCurrent(VCCQ/PE)
Input Pull-Down Current (GND/sOE)
OutputHIGHVoltage
VCC = Max., VIN = GND
VCC = Max., VIN = VCC
VCC = Min., IOH = −12mA
VCC = Min., IOL = 12mA
µ A
µ A
V
VOH
VOL
OutputLOWVoltage
0.55
V
NOTE:
1. These inputs are normally wired to VCC, GND, or unconnected. Internal termination resistors bias unconnected inputs to VCC/2. If these inputs are switched, the function and
timing of the outputs may be glitched, and the PLL may require an additional tLOCK time before all datasheet limits are achieved.
POWERSUPPLYCHARACTERISTICS
Symbol
Parameter
TestConditions(1)
VCC = Max., TEST = MID, REF = LOW,
VCCQ/PE = LOW, GND/sOE = LOW
Alloutputsunloaded
Typ.(2)
Max.
Unit
ICCQ
QuiescentPowerSupplyCurrent
8
25
mA
ΔICC
ICCD
ITOT
Power Supply Current per Input HIGH
Dynamic Power Supply Current per Output
TotalPowerSupplyCurrent
VCC = Max., VIN = 3V
1
30
90
—
—
—
μA
VCC = Max., CL = 0pF
55
29
42
76
μA/MHz
VCC = 3.3V, FREF = 20MHz, CL = 160pF(1)
VCC = 3.3V, FREF = 33MHz, CL = 160pF(1)
VCC = 3.3V, FREF = 66MHz, CL = 160pF(1)
mA
NOTE:
1. For eight outputs, each loaded with 20pF.
INPUTTIMINGREQUIREMENTS
Symbol
tR,tF
tPWC
DH
Description(1)
Maximum input rise and fall times, 0.8V to 2V
Input clock pulse, HIGH or LOW
Input duty cycle
Min.
—
Max.
Unit
ns/V
ns
10
—
90
85
3
10
%
REF
ReferenceClockInput
3.75
MHz
NOTE:
1. Where pulse width implied by DH is less than tPWC limit, tPWC limit applies.
4
IDT5V991A
COMMERCIALANDINDUSTRIALTEMPERATURERANGES
3.3VPROGRAMMABLESKEWPLLCLOCKDRIVERTURBOCLOCK
SWITCHINGCHARACTERISTICSOVEROPERATINGRANGE
IDT5V991A-2
IDT5V991A-5
IDT5V991A-7
Typ.
Symbol Parameter
Min.
Typ.
Max.
Min.
Typ.
Max.
Min.
Max.
Unit
FNOM
tRPWH
tRPWL
tU
VCO Frequency Range
SeePLLProgrammableSkewRangeandResolutionTable
(11)
REF Pulse Width HIGH
3
3
—
—
—
—
3
3
—
—
—
—
3
3
—
—
—
—
ns
ns
(11)
REF Pulse Width LOW
ProgrammableSkewTimeUnit
SeeControlSummaryTable
(1,2,3)
tSKEWPR Zero Output Matched-Pair Skew (xQ0, xQ1)
—
—
—
0.05
0.1
0.2
0.25
0.5
—
—
—
0.1
0.25
0.6
0.25
0.5
—
—
—
0.1
0.3
0.6
0.25
0.75
1
ns
ns
ns
(1,4,5)
tSKEW0 ZeroOutputSkew(AllOutputs)
tSKEW1 OutputSkew
0.25
0.7
(Rise-Rise,Fall-Fall,SameClassOutputs)(1,6)
tSKEW2 OutputSkew
(Rise-Fall,Nominal-Inverted,Divided-Divided)
tSKEW3 OutputSkew
(Rise-Rise,Fall-Fall,DifferentClassOutputs)
tSKEW4 OutputSkew
—
—
—
0.3
0.25
0.5
1.2
0.5
0.9
—
—
—
0.5
0.5
0.5
1.2
0.7
1
—
—
—
1
1.5
1.2
1.7
ns
ns
ns
(1,6)
0.7
1.2
(1,6)
(1,2)
(Rise-Fall,Nominal-Divided,Divided-Inverted)
(1,2,7)
tDEV
tPD
Device-to-Device Skew
—
−0.25
−1.2
—
—
0
0.75
0.25
1.2
2
—
−0.5
−1.2
—
—
0
1.25
0.5
1.2
2.5
3
—
−0.7
−1.2
—
—
0
1.65
0.7
1.2
3
ns
ns
ns
ns
ns
ns
ns
ms
ps
(1,9)
REFInputtoFBPropagationDelay
(1)
tODCV
tPWH
tPWL
tORISE
Output Duty Cycle Variation from 50%
0
0
0
(1,10)
Output HIGH Time Deviation from 50%
—
—
1
—
—
1
—
—
1.5
1.5
—
—
—
(1,11)
OutputLOWTimeDeviationfrom50%
—
1.5
1.2
1.2
0.5
25
—
—
3.5
2.5
2.5
0.5
25
OutputRiseTime(1)
0.15
0.15
—
0.15
0.15
—
1.5
1.5
0.5
25
0.15
0.15
—
tOFALL OutputFallTime(1)
1
1
tLOCK
tJR
PLLLockTime(1,8)
—
—
—
—
—
—
Cycle-to-CycleOutputJitter(1)
RMS
—
—
—
Peak-to-Peak
—
200
—
200
—
200
NOTES:
1. All timing and jitter tolerances apply for FNOM > 25MHz.
2. Skew is the time between the earliest and the latest output transition among all outputs for which the same tU delay has been selected when all are loaded with the specified
load.
3. tSKEWPR is the skew between a pair of outputs (xQ0 and xQ1) when all eight outputs are selected for 0tU.
4. tSKEW0 is the skew between outputs when they are selected for 0tU.
5. For IDT5V991A-2 tSKEW0 is measured with CL = 0pF; for CL = 30pF, tSKEW0 = 0.35ns Max.
6. There are 3 classes of outputs: Nominal (multiple of tU delay), Inverted (4Q0 and 4Q1 only with 4F0 = 4F1 = HIGH), and Divided (3Qx and 4Qx only in Divide-by-2 or Divide-
by-4 mode).
7. tDEV is the output-to-output skew between any two devices operating under the same conditions (VCC, ambient temperature, air flow, etc.)
8. tLOCK is the time that is required before synchronization is achieved. This specification is valid only after VCC is stable and within normal operating limits. This parameter is
measured from the application of a new signal or frequency at REF or FB until tPD is within specified limits.
9. tPD is measured with REF input rise and fall times (from 0.8V to 2V) of 1ns.
10. Measured at 2V.
11. Measured at 0.8V.
5
IDT5V991A
3.3VPROGRAMMABLESKEWPLLCLOCKDRIVERTURBOCLOCK
COMMERCIALANDINDUSTRIALTEMPERATURERANGES
AC TEST LOADS AND WAVEFORMS
VCC
150Ω
Output
150Ω
20pF
Test Load
tOFALL
tORISE
2.0V
0.8V
tPWH
tPWL
LVTTL Output Waveform
≤1ns
≤1ns
3.0V
2.0V
Vth = 1.5V
0.8V
0V
LVTTL Input Test Waveform
6
IDT5V991A
COMMERCIALANDINDUSTRIALTEMPERATURERANGES
3.3VPROGRAMMABLESKEWPLLCLOCKDRIVERTURBOCLOCK
AC TIMING DIAGRAM
tRPW L
tREF
tRPWH
REF
tPD
tODCV
tODCV
FB
tJR
Q
tSKEWPR
tSKEW 0, 1
tSKEWPR
tSKEW 0, 1
OTHER Q
tSKEW2
tSKEW2
INVERTED Q
REF DIVIDED BY 2
REF DIVIDED BY 4
tSKEW 3, 4
tSKEW 3, 4
tSKEW 3, 4
tSKEW 2, 4
tSKEW1, 3, 4
NOTES:
VCCQ/PE: The AC Timing Diagram applies to VCCQ/PE=VCC. For VCCQ/PE=GND, the negative edge of FB aligns with the negative edge of REF, divided outputs change on the
negative edge of REF, and the positive edges of the divide-by-2 and the divide-by-4 signals align.
Skew:
The time between the earliest and the latest output transition among all outputs for which the same tU delay has been selected when all are loaded with 20pF and terminated
with 75Ω to VCC/2.
tSKEWPR:
tSKEW0:
tDEV:
The skew between a pair of outputs (xQ0 and xQ1) when all eight outputs are selected for 0tU.
The skew between outputs when they are selected for 0tU
.
The output-to-output skew between any two devices operating under the same conditions (VCC, ambient temperature, air flow, etc.)
The deviation of the output from a 50% duty cycle. Output pulse width variations are included in tSKEW2 and tSKEW4 specifications.
tODCV:
tPWH is measured at 2V.
tPWL is measured at 0.8V.
tORISE and tOFALL are measured between 0.8V and 2V.
tLOCK:
The time that is required before synchronization is achieved. This specification is valid only after VCC is stable and within normal operating limits. This parameter is measured
from the application of a new signal or frequency at REF or FB until tPD is within specified limits.
7
IDT5V991A
3.3VPROGRAMMABLESKEWPLLCLOCKDRIVERTURBOCLOCK
COMMERCIALANDINDUSTRIALTEMPERATURERANGES
ORDERINGINFORMATION
XXXXX
XX
X
IDT
Package Process
Device Type
Commercial (0°C to +70°C)
Industrial (-40°C to +85°C)
Blank
I
Rectangular Plastic Leaded Chip Carrier
PLCC - Green
J
JG
3.3V Programmable Skew PLL Clock Driver TurboClock
5V991A-2
5V991A-5
5V991A-7
CORPORATE HEADQUARTERS
6024 Silver Creek Valley Road
San Jose, CA 95138
for SALES:
800-345-7015 or 408-284-8200
fax: 408-284-2775
www.idt.com
for Tech Support:
clockhelp@idt.com
8
相关型号:
IDT5V993A-2Q8
PLL Based Clock Driver, 5V Series, 8 True Output(s), 0 Inverted Output(s), PDSO28, QSOP-28
IDT
IDT5V993A-2QG
PLL Based Clock Driver, 5V Series, 8 True Output(s), 0 Inverted Output(s), PDSO28, LEAD FREE, QSOP-28
IDT
©2020 ICPDF网 联系我们和版权申明