M670 [ICSI]
VOLTAGE CONTROLLED SAW OSCILLATOR; 压控振荡器锯型号: | M670 |
厂家: | INTEGRATED CIRCUIT SOLUTION INC |
描述: | VOLTAGE CONTROLLED SAW OSCILLATOR |
文件: | 总6页 (文件大小:352K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
P r o d u c t D a t a S h e e t
Integrated
Circuit
Systems, Inc.
M670
VOLTAGE CONTROLLED SAW OSCILLATOR
GENERAL DESCRIPTION
PIN ASSIGNMENT (5 x 7mm SMT)
The M670 is a VCSO (Voltage Controlled SAW
Oscillator) frequency source for low-jitter
clock generation. Its integrated SAW
(surface acoustic wave) delay line provides
low phase jitter. The M670 is available in a
range of center frequencies. Minimum
M670
( T op View)
pull-range is ±50 ppm (wider pull-range available).
The M670 is well suited for phase-locked loop
implementations, clock and data recovery circuits, and
other timing applications for the telecom and optical
fiber networking markets (e.g., OC-48, OC-192).
FEATURES
Figure 1: Pin Assignment
◆ VCSO center frequencies from 155 to 700 MHz
(Specify center frequency at time of order)
Sample of Available Output Frequencies
VCSO Center Frequency1 (MHz)
Applications
SONET/SDH
◆ Low phase jitter 0.19ps rms typical (50kHz-80MHz)
◆ Low phase noise -70dBc/Hz @ 1kHz offset
◆ Differential 3.3V LVPECL output
622.0800
625.0000
644.5313
669.3265
Gigabit Ethernet
Gigabit Ethernet FEC
SONET/SDH FEC
◆ Single 3.3V power supply
◆ Very small 5 x 7mm SMT (surface mount) package
Table 1: Sample of Available Output Frequencies
Note 1: Specify VCSO center frequency at time of order
BLOCK DIAGRAM
M670
SAW Delay Line
FOUT
Phase
Shifter
nFOUT
VIN
CLK_EN
Figure 2: Block Diagram
M670 Datasheet Rev 12.1
Revised 09Apr2003
M670 Voltage Controlled SAW Oscillator
Integrated Circuit Systems, Inc. ● Communications Modules ● www.icst.com ● tel (508) 852-5400
M670
Integrated
Circuit
Systems, Inc.
VOLTAGE
C
ONTROLLED SAW OSCILLATOR
P r o d u c t D a t a S h e e t
PIN DESCRIPTIONS
I/O
Input
Number
Name
VIN
Configuration
Description
Tuning control voltage.
1
Clock enable:
Logic 1 enables normal operation.
Logic 0 stops the output clock;
nFOUT is held high, FOUT is held low.
2
CLK_EN
GND
Input
3
Ground
Power supply ground connections.
4
5
FOUT
nFOUT
Output
Power
No internal terminator
Clock output pair. Differential LVPECL.
6
VCC
Power supply connection, connect to +3.3V.
Table 2: Pin Descriptions
1
ABSOLUTE MAXIMUM RATINGS
Symbol Parameter
Rating
Unit
VI
Inputs
-0.5 to VCC +0.5
V
VO
VCC
TS
Outputs
-0.5 to VCC +0.5
3.63
V
Power Supply Voltage
Storage Temperature
V
-55 to +125
oC
Table 3: Absolute Maximum Ratings
Note 1:Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the
device. These ratings ard stress specifications only. Functional operation of product at these conditions
or any conditions beyond those listed in Recommended Conditions of Operation, DC Characteristics, or
AC Characteristics is not implied. Exposure to absolute maximum rating conditions for extended periods
may affect product reliability
.
RECOMMENDED CONDITIONS OF OPERATION
Symbol Parameter
Min
Typ
Max
Unit
2.97
3.3
3.63
VCC
Positive Supply Voltage
V
oC
-40
TA
Ambient Operating Temperature
25
+85
Table 4: Recommended Conditions of Operation
M670 Datasheet Rev 12.1
2 of 6
Revised 09Apr2003
Integrated Circuit Systems, Inc. ● Communications Modules ● www.icst.com ● tel (508) 852-5400
M670
Integrated
Circuit
Systems, Inc.
VOLTAGE
C
ONTROLLED SAW OSCILLATOR
P r o d u c t D a t a S h e e t
ELECTRICAL SPECIFICATIONS
DC Characteristics
Unless stated otherwise, VCC = 3.3 Volts + 10%, TA = 0 to 85 oC, VCSO Frequency =622-695MHz, Outputs terminated into 180
Ω to ground
Symbol Parameter
Power Supply VCC Positive Supply Voltage
Pin
Min
2.97
Typ
3.3
Max
3.63
Unit
V
VCC
VIN
80
100
ICC
VIN
Power Supply Current
Input Control Voltage Range
VIN Input Impedence
VIN Modulation Bandwidth
Input High Voltage
mA
V
0
V
Control
Voltage
cc
100
500
kΩ
kHz
V
2
Clock Enable VIH
Pull-up
VIL
V + 0.3
cc
0.8
Input Low Voltage
-0.3
V
IIH
IIL
R
Input High Current
Input Low Current
5
µA
µA
kΩ
CLK_EN
-150
51
Internal Pull-up Resistor
pullup
Differential
Outputs
VOH
Output High Voltage
Output Low Voltage
Peak to Peak Output Voltage
Output Current
V
V
- 0.98
V
- 0.75
- 1.63
V
cc
cc
VOL
- 1.95
V
V
cc
cc
FOUT, nFOUT
0.4
0.6
0.85
20
VP-P
IOUT
VP-P
mA
Table 5: DC Characteristics
AC Characteristics
Unless stated otherwise, VCC = 3.3 Volts + 10%, TA = 0 to 85 oC, VCSO Frequency =622-695MHz, Outputs terminated into 180
Ω
to ground
Symbol Parameter
Min
155
Typ
Max
700
Unit
MHz
Notes
Frequency
FOUT
Output Center Frequency Range
1
±50
APR
fSTAB
Absolute Pull-Range
Frequency Stability
ppm
110
6
ppm p-p
LIN
Tuning Linearity
VCO Gain
%
VIN
= 0.3 to 3.0V
@622.08MHz
265
KVCO
ppm/V
Best fit straight line
-50
-70
Outputs
Non-harmonic Spurious
dBc
100Hz Offset
1kHz Offset
-43
-70
Φn
SSB Phase Noise
offset from carrier
dBc/Hz
dBc/Hz
dBc/Hz
dBc/Hz
ps rms
ps rms
%
10kHz Offset
-98
100kHz Offset
12kHz to 20MHz
50kHz to 80MHz
-124
0.36
0.19
J(t)
Jitter (rms)
2
45
55
odc
tR
Output Duty Cycle
2
300
300
400
400
Output Rise Time for FOUT, nFOUT
ps
ps
20% to 80%
20% to 80%
2
tF
Output Fall Time for FOUT, nFOUT
Table 6: AC Characteristics
Note 1: Consult ICS for availability of other APRs.
Note 2: See Parameter Measurement Information on pg. 4.
M670 Datasheet Rev 12.1
3 of 6
Revised 09Apr2003
Integrated Circuit Systems, Inc. ● Communications Modules ● www.icst.com ● tel (508) 852-5400
M670
Integrated
Circuit
Systems, Inc.
VOLTAGE
C
ONTROLLED SAW OSCILLATOR
P r o d u c t D a t a S h e e t
PARAMETER MEASUREMENT INFORMATION
Output Rise and Fall Time
Output Duty Cycle
nFOUT
80%
80%
V
SWING
20%
t
F
20%
Clock
Outputs
FOUT
t
R
t
PW
(Output Pulse Width)
t
PERIOD
t
PW
Figure 3: Output Rise and Fall Time
odc =
t
PERIOD
Figure 4: Output Duty Cycle
TEST DATA
Broadband Jitter
Output Waveform
Figure 5: Broadband Jitter
Figure 7: Output Waveform
Linearity
Phase Noise
Figure 8: Phase Noise
Figure 6: Linearity
M670 Datasheet Rev 12.1
4 of 6
Revised 09Apr2003
Integrated Circuit Systems, Inc. ● Communications Modules ● www.icst.com ● tel (508) 852-5400
M670
Integrated
Circuit
Systems, Inc.
VOLTAGE
C
ONTROLLED SAW OSCILLATOR
P r o d u c t D a t a S h e e t
DEVICE PACKAGE - 5 x 7mm SMT (Surface Mount) Package
Mechanical Dimensions:
Dimensions are in mm;
dimensions in [ ] are in inches
Unless otherwise specified, all
dimensions are ±0.13 [0.005]
Figure 9: Device Package - 5 x 7mm SMT (Surface Mount) Package
ORDERING INFORMATION
Standard Output Frequencies
155.5200
156.2500
156.8324
161.1328
166.6286
167.2820
167.3280
167.3316
167.7097
168.0400
172.6423
173.3708
622.0800
625.0000
627.3296
644.5313
666.5143
669.1281
669.3120
669.3265
670.8386
672.1600
690.5692
693.4830
For Output Frequency (MHz)
Order Part Number
xxx.xxxx
M670-xxx.xxxx
e.g., 622.0800
M670-622.0800
Table 7: Ordering Information
Table 8: Standard Output Frequencies
Consult ICS for the availability of other VCSO frequencies.
While the information presented herein has been checked for both accuracy and reliability, Integrated Circuit Systems (ICS)
assumes no responsibility for either its use or for the infringement of any patents or other rights of third parties, which would
result from its use. No other circuits, patents, or licenses are implied. This product is intended for use in normal commercial
applications. Any other applications such as those requiring extended temperature range, high reliability, or other extraordinary
environmental requirements are not recommended without additional processing by ICS. ICS reserves the right to change any
circuitry or specifications without notice. ICS does not authorize or warrant any ICS product for use in life support devices or
critical medical instruments.
M670 Datasheet Rev 12.1
5 of 6
Revised 09Apr2003
Integrated Circuit Systems, Inc. ● Communications Modules ● www.icst.com ● tel (508) 852-5400
M670
Integrated
Circuit
Systems, Inc.
VOLTAGE
C
ONTROLLED SAW OSCILLATOR
P r o d u c t D a t a S h e e t
M670 Datasheet Rev 12.1
6 of 6
Revised 09Apr2003
Integrated Circuit Systems, Inc. ● Communications Modules ● www.icst.com ● tel (508) 852-5400
相关型号:
©2020 ICPDF网 联系我们和版权申明