X84640G-2.5 [ICMIC]
Advanced MPS⑩ Micro Port Saver EEPROM with Block Lock⑩ Protection; 先进的MPS ™微型端口保护程序与EEPROM块锁™保护型号: | X84640G-2.5 |
厂家: | IC MICROSYSTEMS |
描述: | Advanced MPS⑩ Micro Port Saver EEPROM with Block Lock⑩ Protection |
文件: | 总22页 (文件大小:564K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
TM
Preliminary Information
ICmic
This X84160/640/128 device has been acquired by
IC MICROSYSTEMS from Xicor, Inc.
IC MICROSYSTEMS
16K/64K/128K
MPSTM EEPROM
X84160/640/128
Advanced MPS™ Micro Port Saver EEPROM with Block Lock™ Protection
FEATURES
bytewide memory control functions, takes a fraction of
the board space and consumes much less power.
•Up to 15MHz data transfer rate
Replacing serial memories, the µPort Saver provides all the
•20ns Read Access Time
serial benefits, such as low cost, low power, low voltage,
•Direct Interface to Microprocessors and
Microcontrollers
—Eliminates I/O port requirements
and small package size while releasing I/Os for more
important uses.
The µPort Saver memory outputs data within 20ns of an
active read signal. This is less than the read access time
—No interface glue logic required
—Eliminates need for parallel to serial converters
of most hosts and provides “no-wait-state” operation. This
prevents bottlenecks on the bus. With rates to
•Low Power CMOS
—1.8V–3.6V, 2.5V–5.5V and 5V 10% Versions
—Standby Current Less than 1µA
15MHz, the µPort Saver supplies data faster than
required by most host read cycle specifications. This
eliminates the need for software NOPs.
—Active Current Less than 1mA
•Byte or Page Write Capable
—32-Byte Page Write Mode
The µPort Saver memories communicate over one line of the
data bus using a sequence of standard bus read and
•New Programmable Block Lock™ Protection
—Software Write Protection
—Programmable Hardware Write Protection
write operations. This “bit serial” interface allows the
µPort Saver to work well in 8-bit, 16 bit, 32-bit, and 64-bit
systems.
•Block Lock (0, 1/4, 1/2, or all of the array)
•Typical Nonvolatile Write Cycle Time: 3ms
The X84160/640/128 provide additional data security
features through Block Lock and programmable Hardware
Write Protection. These allow some or all of the array to
be write protected by software command or by hardware.
System Configuration, Company ID, calibration information,
or other critical data can be secured against unexpected
or inadvertent program operations, leaving the remainder
of the memory available for the system or user access
•High Reliability
—100,000 Endurance Cycles
—Guaranteed Data Retention: 100 Years
•Small Package Options
—8-Lead Mini-DIP Package
—8, 14-Lead SOIC Packages
—8, 20, 28-Lead TSSOP Packages
—8-Lead XBGA Packages
A Write Protect (WP) pin prevents inadvertent writes to the
memory.
DESCRIPTION
Xicor EEPROMs are designed and tested for
applications requiring extended endurance. Inherent data
retention is greater than 100 years.
The µPort Saver memories need no serial ports or special
hardware and connect to the processor memory bus.
Replacing bytewide data memory, the µPort Saver uses
BLOCK DIAGRAM
System Connection
Internal Block Diagram MPS
H.V. GENERATION
TIMING & CONTROL
WP
A15
µP
µC
A0
D7
DSP
ASIC
CE
I/O
OE
EEPROM
ARRAY
COMMAND
DECODE
RISC
X
DEC
D0
AND
CONTROL
LOGIC
16K x 8
8K x 8
2K x 8
P0/CS
OE
P1/CLK
P2/DI
P3/DO
Ports
Saved
WE
WE
Y DECODE
DATA REGISTER
©
Xicor, Inc. 1998 Patents Pending
7067 1.1 6/10/98 T10/C0/D3
Characteristics subject to change without notice
1
X84160/640/128
PIN CONFIGURATIONS: Drawings are to the same scale, actual package sizes are shown in inches:
8-LEAD PDIP
8-LEAD SOIC
8-LEAD TSSOP
PIN NAMES
NC
OE
WE
WP
8
7
6
8
1
2
3
4
1
2
3
4
V
CE
I/O
CC
V
I/O
Data Input/Output
Chip Enable Input
Output Enable Input
Write Enable Input
Write Protect Input
Supply Voltage
CC
CE
I/O
.114 in.
7
6
NC
OE
WE
X84160
X84160
X84640
.190 in.
CE
OE
WE
WP
WP
5
V
SS
V
5
SS
.252 in.
.230 in.
20-LEAD TSSOP
14-LEAD SOIC
NC
1
2
3
4
5
6
7
8
20
19
18
17
16
15
14
13
12
11
NC
NC
V
NC
CE
I/O
CC
CE
I/O
14
13
12
11
10
1
2
3
4
5
6
7
V
CC
V
CC
NC
NC
NC
V
NC
NC
NC
NC
OE
WE
NC
Ground
SS
X84640
NC
NC
NC
WP
NC
NC
NC
WP
.250 in.
NC
No Connect
X84128
.390 in.
NC
OE
WE
V
9
10
SS
NC
9
PACKAGE
SELECTION GUIDE
V
8
SS
.252 in.
28-LEAD TSSOP
8-Lead PDIP
84160 8-Lead SOIC
8-Lead TSSOP
.230 in.
NC
1
2
3
4
5
6
7
8
9
10
NC
NC
NC
NC
28
27
26
25
24
23
22
21
20
19
18
17
16
15
NC
CE
CE
CE
I/O
NC
NC
NC
WP
8-LEAD XBGA: Top View
V
8-Lead CSP/BGA
CC
NC
NC
NC
NC
OE
8-Lead PDIP
8-Lead SOIC
84640
V
.394 in.
I/O
1
2
3
4
8
CC
X84128
20-Lead TSSOP
NC
CE
V
7
6
5
V
WE
NC
NC
11
12
13
SS
SS
WE
OE
8-Lead CSP/BGA
NC
NC
NC
8-Lead PDIP
84128
WP
14
NC
14-Lead SOIC
. 252 in.
28-Lead TSSOP
.078 in.
PIN DESCRIPTIONS
Chip Enable (CE)
Write Protect (WP)
The Write Protect input controls the Hardware Write Pro-
tect feature. When WP is LOW and the nonvoltaile bit
WPEN is “1”, nonvolatile writes of the X84160/640/128
control register is disabled, but the part otherwise func-
tions normally. When WP is held HIGH, all functions,
including nonvolatile write operate normally. WP going
LOW while CS is still LOW will interrupt a write to the
X84160/640/128 control register. If the internal Write
cycle has already been initiated, WP going LOW will
have no effect on write.
The Chip Enable input must be LOW to enable all read/
write operations. When CE is HIGH, the chip is dese-
lected, the I/O pin is in the high impedance state, and
unless a nonvolatile write operation is underway, the
device is in the standby power mode.
Output Enable (OE)
The Output Enable input must be LOW to enable the out-
put buffer and to read data from the device on the I/O line.
The WP pin function is blocked when the WPEN bit in the
control register is “0”. This allows the user to install the
X84160/640/128 in a system with WP pin grounded and
still be able to write to the control register. The WP pin
functions will be enabled when the WPEN bit is set “1”.
Write Enable (WE)
The Write Enable input must be LOW to write either data
or command sequences to the device.
Data In/Data Out (I/O)
Data and command sequences are serially written to or
serially read from the device through the I/O pin.
2
X84160/640/128
DEVICE OPERATION
sequence and enter the low power standby state, other-
wise the device will await further reads in the sequential
read mode.
The X84160/640/128 are serial EEPROMs designed to
interface directly with most microprocessor buses. Stan-
dard CE, OE, and WE signals control the read and write
operations, and a single l/O line is used to send and
receive data and commands serially.
Sequential Read
The byte address is automatically incremented to the
next higher address after each byte of data is read. The
data stored in the memory at the next address can be
read sequentially by continuing to issue read cycles.
When the highest address in the array is reached, the
address counter rolls over to address 0000h and reading
may be continued indefinitely.
Data Timing
Data input on the l/O line is latched on the rising edge of
either WE or CE, whichever occurs first. Data output on
the l/O line is active whenever both OE and CE are LOW.
Care should be taken to ensure that WE and OE are
never both LOW while CE is LOW.
Reset Sequence
The reset sequence resets the device and sets an inter-
nal write enable latch. A reset sequence can be sent at
any time by performing a read/write “0”/read operation
(see Figs. 1 and 2). This breaks the multiple read or write
cycle sequences that are normally used to read from or
write to the part. The reset sequence can be used at any
time to interrupt or end a sequential read or page load.
As soon as the write “0” cycle is complete, the part is
reset (unless a nonvolatile write cycle is in progress).The
second read cycle in this sequence, and any further read
cycles, will read a HIGH on the l/O pin until a valid read
sequence (which includes the address) is issued. The
reset sequence must be issued at the beginning of both
read and write sequences to be sure the device initiates
these operations properly.
Read Sequence
A read sequence consists of sending a 16-bit address
followed by the reading of data serially. The address is
written by issuing 16 separate write cycles (WE and CE
LOW, OE HIGH) to the part without a read cycle between
the write cycles.The address is sent serially, most signifi-
cant bit first, over the I/O line. Note that this sequence is
fully static, with no special timing restrictions, and the pro-
cessor is free to perform other tasks on the bus when-
ever the device CE pin is HIGH. Once the 16 address
bits are sent, a byte of data can be read on the I/O line by
issuing 8 separate read cycles (OE and CE LOW, WE
HIGH). At this point, writing a ‘1’ will terminate the read
Figure 1. Read Sequence
CE
OE
WE
"0"
A10
A15 A14 A13 A12 A11
A9 A8 A7 A6 A5 A4 A3 A2 A1 A0
I/O (IN)
D7 D6 D5 D4 D3 D2 D1 D0
I/O (OUT)
RESET
LOAD ADDRESS
READ DATA
WHEN ACCESSING: X84160 ARRAY: A15–A11=0
X84640 ARRAY: A15–A13=0
X84128 ARRAY: A15–A14=0
7008 FRM F04.1
3
X84160/640/128
Figure 2: Write Sequence
CE
OE
WE
"0"
A10
A15 A14 A13 A12 A11
A9 A8 A7 A6 A5 A4 A3 A2 A1 A0
D7 D6 D5 D4 D3 D2 D1 D0
I/O (IN)
"1"
"0"
I/O (OUT)
RESET
LOAD ADDRESS
LOAD DATA
START
NONVOLATILE
WRITE
WHEN ACCESSING: X84160 ARRAY: A15–A11=0
X84640 ARRAY: A15–A13=0
X84128 ARRAY: A15–A14=0
7008 FRM F05.1
Write Sequence
page, where data loading can continue. For this reason,
sending more than 256 consecutive data bits will result in
overwriting previous data.
A nonvolatile write sequence consists of sending a reset
sequence, a 16-bit address, up to 32 bytes of data, and
then a special “start nonvolatile write cycle” command
sequence.
A nonvolatile write cycle will not start if a partial or incom-
plete write sequence is issued. The internal write enable
latch is reset when the nonvolatile write cycle is com-
pleted and after an invalid write to prevent inadvertent
writes. Note that this sequence is fully static, with no spe-
cial timing restrictions. The processor is free to perform
other tasks on the bus whenever the chip enable pin (CE)
is HIGH.
The reset sequence is issued first (as described in the
Reset Sequence section) to set an internal write enable
latch. The address is written serially by issuing 16
separate write cycles (WE and CE LOW, OE HIGH) to
the part without any read cycles between the writes. The
address is sent serially, most significant bit first, on the
l/O pin. Up to 32 bytes of data are written by issuing a
multiple of 8 write cycles. Again, no read cycles are
allowed between writes.
Nonvolatile Write Status
The status of a nonvolatile write cycle can be determined
at any time by simply reading the state of the l/O pin on
the device. This pin is read when OE and CE are LOW
and WE is HIGH. During a nonvolatile write cycle the l/O
pin is LOW. When the nonvolatile write cycle is complete,
the l/O pin goes HIGH. A reset sequence can also be
issued during a nonvolatile write cycle with the same
result: I/O is LOW as long as a nonvolatile write cycle is
in progress, and l/O is HIGH when the nonvolatile write
cycle is done.
The nonvolatile write cycle is initiated by issuing a special
read/write “1”/read sequence. The first read cycle ends
the page load, then the write “1” followed by a read starts
the nonvolatile write cycle. The device recognizes 32-
byte pages (e.g., beginning at addresses XXXXXX00000
for X84160).
When sending data to the part, attempts to exceed the
upper address of the page will result in the address
counter “wrapping-around” to the first address on the
4
X84160/640/128
CONTROL REGISTER
The Write Protect (WP) pin and the nonvolatile Write
Protect Enable (WPEN) bit in the Status Register control
the programmable hardware write protect feature.
Hardware write protection is enabled when WP pin is
LOW, and the WPEN bit is “1”. Hardware write protection
is disabled when either the WP pin is HIGH or the WPEN
bit is “0”. When the chip is hardware write protected,
nonvolatile write is disabled to the Control Register,
including the Block Protect bits and the WPEN bit itself,
as well as the block-protected sections in the memory
array. Only the sections of the memory array that are not
block-protected can be written.
The X84160/640/128 has one register that contains
control bits for the devices. The control bits, WPEN, BP1,
and BP0, are shown in Table 1. To read or change the
contents of this register requires a one byte operation to
address FFFFh.
A read from FFFFh returns the one byte contents of the
control register unused bits return 0. Continued reads
return undefined data. A write to address FFFFh changes
the value of the bits. Unused bits are written as “0”.
Writing more than one byte to the control register is a
violation and the operation will be aborted. After sending
one byte to the control register, a start nonvolatile write
cycle will latch in the new state.
Note: When the WP pin is tied to V and the WPEN bit is HIGH, the
SS
WPEN bit is write protected. It cannot be changed back to a
“0”, as long as the WP pin is held LOW.
Table 1
BP1, BP0: Block Protect Bits
7
6
0
5
0
4
0
3
2
1
0
0
0
The Block Protect (BP0 and BP1) bits are nonvolatile and
allow the user to select one of four levels of protection.
The X84160/640/128 is divided into four segments. One,
two, or all four of the segments may be protected.That is,
the user may read the segments but will be unable to
alter (write) data within the selected segments. The
partitioning is controlled as illustrated in table 3 below.
WPEN
BP1 BP0
WPEN: Write Protect Enable Bit
The Write-Protect-Enable (WPEN) bit is an enable bit for
the WP pin.
Table 2
Protected Unprotected
Status
WPEN
WP
X
Blocks
Protected
Protected
Blocks
Writable
Writable
Writable
Register
0
1
X
Writable
Protected
Writable
LOW
HIGH Protected
Table 3. Block Lock Protection
Control Register Bits
Array Address Protected
BP1
0
BP0
0
X84160
X84640
None
X84128
None
Array
None
0
1
0600h–07FFh
0400h–07FFh
1800h–1FFFh
1000h–1FFFh
3000h–3FFFh
2000h–3FFFh
upper 1/4
upper 1/2
Full Array
1
0
1
1
0000–07FFh
0000–1FFFh
0000h–3FFFh
(Not including the
control register.)
5
X84160/640/128
Low Power Operation
—A reset sequence must be issued to set the internal
write enable latch before starting a write sequence.
The device enters an idle state, which draws minimal cur-
rent when:
—A special “start nonvolatile write” command sequence
is required to start a nonvolatile write cycle.
—an illegal sequence is entered. The following are the
more common illegal sequences:
—The internal Write Enable latch is reset automatically
at the end of a nonvolatile write cycle.
• Read/Write/Write—any time
—The internal Write Enable latch is reset and remains
reset as long as the WP pin is LOW, which blocks all
nonvolatile write cycles.
• Read/Write ‘1’—When writing the address or
writing data.
• Write ‘1’—when reading data
—The internal Write Enable latch resets on an invalid
write operation.
• Read/Read/Write ‘1’—after data is written to
device, but before entering the NV write sequence.
SYMBOL TABLE
—the device powers-up;
WAVEFORM
INPUTS
OUTPUTS
—a nonvolatile write operation completes.
While a sequential read is in progress, the device
remains in an active state. This state draws more current
than the idle state, but not as much as during a read
itself. To go back to the lowest power condition, an invalid
condition is created by writing a ‘1’ after the last bit of a
read operation.
Must be
steady
Will be
steady
May change
from LOW to
HIGH
Will change
from LOW to
HIGH
May change
Will change
from HIGH to from HIGH to
LOW
LOW
Write Protection
Don’t Care:
Changes
Allowed
Changing:
State Not
Known
The following circuitry has been included to prevent
inadvertent nonvolatile writes:
N/A
Center Line
is High
Impedance
—The internal Write Enable latch is reset upon
power-up.
6
X84160/640/128
ABSOLUTE MAXIMUM RATINGS*
*COMMENT
Temperature under Bias ......................–65°C to +135°C
Storage Temperature...........................–65°C to +150°C
Terminal Voltage with
Stresses above those listed under “Absolute Maximum
Ratings” may cause permanent damage to the device.
This is a stress rating only and the functional operation
of the device at these or any other conditions above
those indicated in the operational sections of this speci-
fication is not implied. Exposure to absolute maximum
rating conditions for extended periods may affect device
reliability.
Respect to V .......................................–1V to +7V
SS
DC Output Current................................................... 5mA
Lead Temperature (Soldering, 10 seconds)..........300°C
RECOMMENDED OPERATING CONDITIONS
Temperature
Commercial
Industrial
Min.
0°C
Max.
+70°C
+85°C
+125°C
Supply Voltage
X84160/640/128
Limits
4.5V to 5.5V
2.5V to 5.5V
1.8V to 3.6V
–40°C
–55°C
X84160/640/128 – 2.5
X84160/640/128 – 1.8
Military†
Notes: †Contact factory for Military availability
D.C. OPERATING CHARACTERISTICS (V
= 5V 10%)
CC
(Over the recommended operating conditions, unless otherwise specified.)
Limits
Symbol
Parameter
Min.
Max.
Units
Test Conditions
I
V
V
Supply Current (Read)
1
mA
OE = V , WE = V , I/O = Open,
CC1
CC
IL
IH
CE clocking = V
x 0.1/V
x 0.9
CC
CC
@ 10 MHz
I
During Nonvolatile Write Cycle
CC
I
Supply Current (Write)
Standby Current
2
mA
CC2
CC
CC
All Inputs at CMOS Levels
I
I
I
V
CE = V , Other Inputs = V or V
CC CC SS
1
µA
µA
µA
V
SB1
V
= V to V
SS
Input Leakage Current
Output Leakage Current
Input LOW Voltage
10
10
LI
IN
CC
V
= V to V
CC
LO
OUT
SS
(1)
(1)
V
V
x 0.3
V
–0.5
CC
lL
V
V
x 0.7
+ 0.5
CC
V
V
V
Input HIGH Voltage
Output LOW Voltage
Output HIGH Voltage
V
V
V
CC
IH
I
= 2.1mA
0.4
OL
OL
– 0.8
I
= –1mA
OH
CC
OH
Notes: (1) V Min. and V Max. are for reference only and are not tested.
IL
IH
7
X84160/640/128
D.C. OPERATING CHARACTERISTICS (V
= 2.5V to 5.5V)
CC
(Over the recommended operating conditions, unless otherwise specified.)
Limits
Symbol
Parameter
Units
µA
Test Conditions
OE = V , WE = V , I/O = Open,
Min.
Max.
IL
IH
I
V
Supply Current (Read)
CE clocking = V x 0.1/V x 0.9 @
300
CC1
CC
CC CC
V
= 2.5, 5 MHz
CC
I
During Nonvolatile Write Cycle
CC
I
V
V
Supply Current (Write)
Standby Current
2
mA
CC2
CC
CC
All Inputs at CMOS Levels
I
CE = V , Other Inputs = V or V
SS
1
µA
µA
µA
V
SB1
CC
CC
I
V
V
= V to V
CC
Input Leakage Current
Output Leakage Current
Input LOW Voltage
10
10
LI
IN
SS
I
= V to V
SS CC
LO
OUT
(1)
V
V
V
x 0.3
–0.5
CC
lL
(1)
V
V
V
x 0.7
+ 0.5
CC
Input HIGH Voltage
Output LOW Voltage
Output HIGH Voltage
V
V
V
CC
CC
CC
IH
V
I
= 1mA, V
= 3V
0.4
OL
OL
CC
V
– 0.4
I
= –400µA, V
= 3V
OH
OH
CC
D.C. OPERATING CHARACTERISTICS (V
(Over the recommended operating conditions, unless otherwise specified.)
= 1.8V to 3.6V)
Limits
Symbol
Parameter
Units
µA
Test Conditions
OE = V , WE = V , I/O = Open,
Min.
Max.
IL
IH
I
V
Supply Current (Read)
CE clocking = V x 0.1/V x 0.9 @
200
CC1
CC
CC CC
V
= 1.8V, 4 MHz
CC
I
During Nonvolatile Write Cycle
CC
I
V
V
Supply Current (Write)
Standby Current
1
mA
CC2
CC
CC
All Inputs at CMOS Levels
I
CE = V , Other Inputs = V or V
SS
1
µA
µA
µA
V
SB1
CC
CC
I
V
V
= V to V
CC
Input Leakage Current
Output Leakage Current
Input LOW Voltage
10
10
LI
IN
SS
I
= V to V
SS CC
LO
OUT
(1)
V
V
V
x 0.3
–0.5
CC
lL
(1)
V
V
V
x 0.7
+ 0.5
CC
Input HIGH Voltage
Output LOW Voltage
Output HIGH Voltage
V
CC
IH
V
I
= 0.5mA, V
= 2V
0.4
V
OL
OL
CC
V
– 0.2
I
= –250µA, V
= 2V
V
OH
CC
OH
CC
Notes: (1) V Min. and V Max. are for reference only and are not tested.
IL
IH
8
X84160/640/128
CAPACITANCE
T = +25°C, f = 1MHz, V
= 5V
A
CC
Symbol
Parameter
Max.
Units
Test Conditions
(2)
V
= 0V
= 0V
C
C
Input/Output Capacitance
8
pF
I/O
I/O
(2)
V
Input Capacitance
6
pF
IN
IN
Notes: (2) Periodically sampled, but not 100% tested.
POWER-UP TIMING
Symbol
Parameter
Max.
Units
(3)
t
t
Power-up to Read Operation
2
ms
ms
PUR
(3)
Power-up to Write Operation
5
PUW
Notes: (3) Time delays required from the time the V is stable until the specific operation can be initiated.
CC
Periodically sampled, but not 100% tested.
A.C. CONDITIONS OF TEST
V
x 0.1 to V x 0.9
CC
Input Pulse Levels
CC
Input Rise and Fall Times
5ns
V
x 0.5
Input and Output Timing Levels
CC
EQUIVALENT A.C. LOAD CIRCUITS
2V
5V
3V
2.8KΩ
2.06KΩ
2.39KΩ
OUTPUT
5.6KΩ
OUTPUT
OUTPUT
4.58KΩ
3.03KΩ
30pF
30pF
30pF
9
X84160/640/128
A.C. CHARACTERISTICS
(Over the recommended operating conditions, unless otherwise specified.)
Read Cycle Limits – X84160/640/128
V
= 4.5V – 5.5V V = 2.5V – 5.5V V = 1.8V – 3.6V
CC CC
CC
Symbol
Parameter
Read Cycle Time
Min.
70
Max
Min.
125
Max.
Min.
250
Max.
Units
ns
t
RC
t
CE Access Time
20
20
25
25
70
70
ns
CE
t
OE Access Time
ns
OE
t
OE Pulse Width
20
50
20
50
0
35
90
35
90
0
70
180
70
180
0
ns
OEL
t
OE High Recovery Time
CE LOW Time
ns
OEH
t
ns
LOW
t
CE HIGH Time
ns
HIGH
(4)
t
CE LOW to Output In Low Z
ns
ns
LZ
(4)
t
CE HIGH to Output In High Z
0
15
15
0
25
25
0
30
30
HZ
(4)
t
OE LOW to Output In Low Z
OE HIGH to Output In High Z
Output Hold from CE or OE HIGH
WE HIGH Setup Time
0
0
0
0
0
0
ns
ns
ns
ns
ns
OLZ
(4)
t
OHZ
t
0
0
0
OH
t
25
25
25
25
25
25
WES
t
WE HIGH Hold Time
WEH
Notes: (4) Periodically sampled, but not 100% tested. t and t
are measured from the point where CE or OE goes HIGH (whichever occurs
HZ
OHZ
first) to the time when I/O is no longer being driven into a 5pF load.
t
RC
t
t
HIGH
LOW
t
CE
CE
WE
OE
t
WES
t
OEL
t
OEH
t
OE
t
WEH
t
OHZ
I/O
HIGH Z
DATA
t
OH
t
t
OLZ
LZ
t
HZ
10
X84160/640/128
Write Cycle Limits – X84160/640/128
V
= 4.5V – 5.5V
V
= 2.5V – 5.5V V = 1.8V – 3.6V
CC
CC CC
Symbol
Parameter
Min.
Max.
Min.
Max.
Min.
Max.
Units
(5)
t
5
5
5
Nonvolatile Write Cycle Time
Write Cycle Time
ms
ns
ns
ns
ns
ns
ns
ns
ns
ns
NVWC
WC
t
t
70
20
50
0
125
35
90
0
250
50
180
0
WE Pulse Width
WP
t
t
t
t
t
t
t
t
t
WE HIGH Recovery Time
Write Setup Time
WPH
CS
Write Hold Time
0
0
0
CH
CE Pulse Width
20
50
25
25
12
35
90
25
25
20
70
180
50
50
30
CP
CE HIGH Recovery Time
OE HIGH Setup Time
OE HIGH Hold Time
CPH
OES
OEH
(6)
Data Setup Time
Data Hold Time
WP HIGH Setup
WP HIGH Hold
ns
ns
ns
ns
DS
(6)
5
5
5
DH
(7)
(7)
t
t
100
100
100
100
150
150
WPSU
WPHD
Notes: (5) t
is the time from the falling edge of OE or CE (whichever occurs last) of the second read cycle in the “start nonvolatile write cycle”
NVWC
sequence until the self-timed, internal nonvolatile write cycle is completed.
(6) Data is latched into the X84160/640/128 on the rising edge of CE or WE, whichever occurs first.
(7) Periodically sampled, but not 100% tested.
11
X84160/640/128
CE Controlled Write Cycle
t
CPH
t
CP
CE
t
t
OEH
OES
OE
WE
WP
I/O
t
CS
t
CH
t
WP
t
WPH
t
t
WPSU
WPHD
t
t
DS
DH
HIGH Z
DATA
t
WC
WE Controlled Write Cycle
t
CPH
t
CP
CE
t
OES
t
OE
WE
WP
I/O
CS
t
CH
t
OEH
t
WPH
t
WP
t
WPHD
t
WPSU
t
t
DS
DH
HIGH Z
DATA
t
WC
12
X84160/640/128
8-LEAD XBGA TYPE
X84640Z: Bottom View
1200 30
V
CC
I/O
CE
NC
V
WE
SS
OE
WP
1982 30
1982 30
140 20
NOTE: ALL DIMENSIONS IN µM
ALL DIMENSIONS ARE TYPICAL VALUES
13
X84160/640/128
8-LEAD XBGA TYPE
X84128: Bottom View
1200 30
V
CC
I/O
CE
NC
V
WE
OE
SS
WP
1982 30
1982 30
140 20
NOTE: ALL DIMENSIONS IN µM
ALL DIMENSIONS ARE TYPICAL VALUES
14
X84160/640/128
8-LEAD PLASTIC DUAL IN-LINE PACKAGETYPE P
0.430 (10.92)
0.360 (9.14)
0.260 (6.60)
0.240 (6.10)
PIN 1 INDEX
PIN 1
0.060 (1.52)
0.020 (0.51)
0.300
(7.62) REF.
HALF SHOULDER WIDTH ON
ALL END PINS OPTIONAL
0.145 (3.68)
0.128 (3.25)
SEATING
PLANE
0.025 (0.64)
0.015 (0.38)
0.150 (3.81)
0.125 (3.18)
0.065 (1.65)
0.045 (1.14)
0.110 (2.79)
0.090 (2.29)
0.020 (0.51)
0.016 (0.41)
0.325 (8.25)
0.300 (7.62)
.073 (1.84)
MAX.
0°
TYP 0.010 (0.25)
15°
.
NOTE:
1. ALL DIMENSIONS IN INCHES (IN PARENTHESES IN MILLIMETERS)
2. PACKAGE DIMENSIONS EXCLUDE MOLDING FLASH
15
X84160/640/128
8-LEAD PLASTIC SMALL OUTLINE GULL WING PACKAGE TYPE S
0.150 (3.80)
0.158 (4.00)
0.228 (5.80)
0.244 (6.20)
PIN 1 INDEX
PIN 1
0.014 (0.35)
0.019 (0.49)
0.188 (4.78)
0.197 (5.00)
(4X) 7°
0.053 (1.35)
0.069 (1.75)
0.004 (0.19)
0.010 (0.25)
0.050 (1.27)
0.010 (0.25)
0.020 (0.50)
0.050"TYPICAL
X 45°
0.050"
TYPICAL
0° – 8°
0.0075 (0.19)
0.010 (0.25)
0.250"
0.016 (0.410)
0.037 (0.937)
0.030"
TYPICAL
8 PLACES
FOOTPRINT
NOTE: ALL DIMENSIONS IN INCHES (IN PARENTHESES IN MILLIMETERS)
16
X84160/640/128
PACKAGING INFORMATION
14-LEAD PLASTIC SMALL OUTLINE GULLWING PACKAGETYPE S
0.150 (3.80)
0.158 (4.00)
0.228 (5.80)
0.244 (6.20)
PIN 1 INDEX
PIN 1
0.014 (0.35)
0.020 (0.51)
0.336 (8.55)
0.345 (8.75)
(4X) 7°
0.053 (1.35)
0.069 (1.75)
0.004 (0.10)
0.010 (0.25)
0.050 (1.27)
0.050" Typical
0.010 (0.25)
0.020 (0.50)
X 45°
0.050" Typical
0° – 8°
0.250"
0.0075 (0.19)
0.010 (0.25)
0.016 (0.410)
0.037 (0.937)
0.030"Typical
14 Places
FOOTPRINT
NOTE: ALL DIMENSIONS IN INCHES (IN PARENTHESES IN MILLIMETERS)
17
X84160/640/128
PACKAGING INFORMATION
8-LEAD PLASTIC, TSSOP, PACKAGE TYPE V
.025 (.65) BSC
.169 (4.3)
.252 (6.4) BSC
.177 (4.5)
.114 (2.9)
.122 (3.1)
.047 (1.20)
.0075 (.19)
.0118 (.30)
.002 (.05)
.006 (.15)
.010 (.25)
Gage Plane
0° – 8°
Seating Plane
.019 (.50)
.029 (.75)
DetailA (20X)
.031 (.80)
.041 (1.05)
See Detail “A”
NOTE: ALL DIMENSIONS IN INCHES (IN PARENTHESES IN MILLIMETERS)
18
X84160/640/128
PACKAGING INFORMATION
20-LEAD PLASTIC, TSSOP PACKAGE TYPE V
.025 (.65) BSC
.169 (4.3)
.252 (6.4) BSC
.177 (4.5)
.252 (6.4)
.300 (6.6)
.047 (1.20)
.0075 (.19)
.002 (.05)
.0118 (.30)
.006 (.15)
.010 (.25)
Gage Plane
0° – 8°
Seating Plane
.019 (.50)
.029 (.75)
DetailA (20X)
.031 (.80)
.041 (1.05)
See Detail “A”
NOTE: ALL DIMENSIONS IN INCHES (IN PARENTHESES IN MILLIMETERS)
19
X84160/640/128
PACKAGING INFORMATION
28-LEAD PLASTIC, TSSOP PACKAGE TYPE V
.025 (.65) BSC
.169 (4.3)
.252 (6.4) BSC
.177 (4.5)
.394 (10.0)
.047 (1.20)
.0075 (.19)
.002 (.05)
.0118 (.30)
.006 (.15)
.010 (.25)
Gage Plane
0° – 8°
Seating Plane
.019 (.50)
.029 (.75)
DetailA (20X)
.031 (.80)
.041 (1.05)
See Detail “A”
NOTE: ALL DIMENSIONS IN INCHES (IN PARENTHESES IN MILLIMETERS)
20
X84160/640/128
ORDERING INFORMATION
X84160/640/128 P
T
G –V
V
CC
Range
Blank = 4.5V to 5.5V, 10 MHz
2.5 = 2.5V to 5.5V, 5 MHz
1.8 = 1.8V to 3.6V, 4 MHz
Device
G = RoHS Compliant Lead Free package
Blank = Standard package. Non lead free
Temperature Range
Blank = Commercial = 0°C to +70°C
E = Extended = –20°C to +85°C
I = Industrial = –40°C to +85°C
Military = –55°C to +125°C (contact factory)
Packages:
X84160
P = 8-Lead PDIP
S8 = 8-Lead SOIC
V8 = 8-Lead TSSOP
*PART MARK CONVENTION
8-Lead TSSOP
8-Lead SOIC/PDIP
X84640
P = 8-Lead PDIP
S8 = 8-Lead SOIC
EYWW
8160XXG
X84160G
XXX
Blank = 8-Lead SOIC
P = 8-Lead PDIP
G = RoHS compliant lead free
G = RoHS compliant
lead free
V20 = 20-Lead TSSOP
Z = 8-Lead XBGA
AG = 1.8 to 3.6V, 0 to +70°C
AH = 1.8 to 3.6V, -40 to +85°C
F = 2.5 to 5.5V, 0 to +70°C
G = 2.5 to 5.5V, -40 to +85°C
Blank = 4.5 to 5.5V, 0 to +70°C
I = 4.5 to 5.5V, -40 to +85°C
AG = 1.8 to 3.6V, 0 to +70°C
AH = 1.8 to 3.6V, -40 to +85°C
F = 2.5 to 5.5V, 0 to +70°C
G = 2.5 to 5.5V, -40 to +85°C
X84128
P = 8-Lead PDIP
S14 = 14-Lead SOIC
V28 = 28-Lead TSSOP
Z = 8-Lead XBGA
Blank = 4.5 to 5.5V, 0 to +70°C
I = 4.5 to 5.5V, -40 to +85°C
8-Lead XBGA PACKAGE
Complete Part Number
Top Mark
X84640ZE-2.5
X84640ZI-2.5
X84128ZE-2.5
X84128 ZI-2.5
XAP
XAR
XAN
XAO
*All parts and package types not included will receive standard marking.
21
X84160/640/128
LIMITED WARRANTY
Devices sold by Xicor, Inc. are covered by the warranty and patent indemnification provisions appearing in its Terms of Sale only. Xicor, Inc. makes no
warranty, express, statutory, implied, or by description regarding the information set forth herein or regarding the freedom of the described devices from
patent infringement. Xicor, Inc. makes no warranty of merchantability or fitness for any purpose. Xicor, Inc. reserves the right to discontinue production
and change specifications and prices at any time and without notice.
Xicor, Inc. assumes no responsibility for the use of any circuitry other than circuitry embodied in a Xicor, Inc. product. No other circuits, patents, licenses
are implied.
U.S. PATENTS
Xicor products are covered by one or more of the following U.S. Patents: 4,263,664; 4,274,012; 4,300,212; 4,314,265; 4,326,134; 4,393,481; 4,404,475;
4,450,402; 4,486,769; 4,488,060; 4,520,461; 4,533,846; 4,599,706; 4,617,652; 4,668,932; 4,752,912; 4,829, 482; 4,874, 967; 4,883, 976. Foreign
patents and additional patents pending.
LIFE RELATED POLICY
In situations where semiconductor component failure may endanger life, system designers using this product should design the system with
appropriate error detection and correction, redundancy and back-up features to prevent such an occurence.
Xicor's products are not authorized for use in critical components in life support devices or systems.
1. Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain
life, and whose failure to perform, when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected
to result in a significant injury to the user.
2. A critical component is any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure
of the life support device or system, or to affect its safety or effectiveness.
22
相关型号:
©2020 ICPDF网 联系我们和版权申明