U.FL-LP-5016-A-(35) [HRS]
Interconnection Device;
| 型号： | U.FL-LP-5016-A-(35) |
| 厂家： | 
HRS |
| 描述： | Interconnection Device 连接器 |
| 文件： | 总6页 (文件大小：215K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
SMT Ultra miniature coaxial connectors
U.FL Series
Figure 1. Mating height comparison
(with other Hirose Electric products)
U.FL
E.FL
ꢀSpace factor of mated connector
ꢀFeatures
Figure 2. U.FL-LP-040 and U.FL-R-SMT
1. Mating heights one of the world’s lowest profile
Height from the printed circuit board when mated with a receptacle with
a (right-angle) plug is more than 2.5 mm!
2. Extremely small board occupation area
In comparison with our E.FL Series of SMT coaxial connectors, the
receptacles offer a reduction of the board occupation area of
approximately 18%, which results in an area of just 7.7 mm2.
U.FL-R-SMT
U.FL-LP-040
3. World’s lightest
These are the world’s lightest coaxial connectors.
Receptacle is only 15.7 mg
Right-angle plugs + female center contacts for Ø 0.81 mm cable
is no more than 53.7 mg, and for Ø 1.32 mm cable is just 59.1 mg
4. Can be used with a frequency of up to 3 GHz
To meet the frequency requirements of a wide variety of miniature
equipment, these connectors offer high frequency performance
from DC to 3 GHz with a V.S.W.R. of up to 1.3.
Figure 3. U.FL-LP-066and U.FL-R-SMT
5. Can be used with automatic mounting
The embossed tape packaging specification of the receptacles
permits automatic mounting.
U.FL-R-SMT
U.FL-LP-066
6. Use of ultra-fine Teflon cable
From among the types of suitable cable, Ø 0.8 mm (single shield)
outside diameter ultra-fine Teflon coaxial cable has been made a
standard specification in consideration of improving the
construction qualities and construction area.
An external diameter Ø1.32 mm (double shield) & Ø1.13mm (single
shield) ultra-fine Teflon coaxial cable specification is also available.
7. Simple removal of connectors
The extraction jig permits simple removal of connectors.
ꢀApplications
8. Mating checks are easy
Mobile phones, wireless communications
equipment, electronic measuring instruments,
GPS, wireless LAN, Bluetooth etc.
Subminiature size notwithstanding, the lock sensation permits a
check of sure mating.
1
ꢀ Product specifications
Nominal characteristic impedance
50ø
60 V AC (rms)
DC to 3 GHz
Operating temperature range
Operating humidity
-40˚C to +90˚C
90% max.
Ratings
Rated voltage
Rated frequency
Item
Conditions
Specification
Center: 20mø or less
1. Contact resistance
Measured at 10 mA or less
Outside: 10mø or less
2. Insulation resistance
3. Withstand voltage
4. V.S.W.R.*
Measured at 100 V DC
200 V AC for 1 minute
DC to 3 GHz
500 Mø or more
No line or insulation breakdown
1.3 max.
5. Female contact holding force
0.15 N min.
Measured with a Ø 0.475 pin gauge
25mø or less (Center)
15mø or less (Outside)
6. Repetitive operation
7. Vibration
30 cycles of insertion and disengagement
Contact resistance
No momentary disconnections of 1 µs or more
No damage, cracks, or loose parts
Frequency of 10 to 100 Hz, single amplitude of 1.5 mm,
acceleration of 59 m/s2, for 5 cyles in the direction of each of the 3 axes
No momentary disconnections of 1 µs or more
No damage, cracks, or loose parts
Acceleration of 735 m/s2, 11 ms duration, sine half-wave
waveform, for 6 cycles in the direction of each of the 3 axes
8. Shock
No damage, cracks, or loose parts
Insulation resistance 100mø or more
Insulation resistance 500mø or more
9. Humidity resistance
9. (Steady state)
Temperature of 40˚C, humidity of 95%,
let stand for 96 hours
No damage, cracks, or loose parts
Contact resistance 25mø or less (Center)
15mø or less (Outside)
Temperature: +40˚C
5 to 35˚C
Within 5 min.
+90˚C
30 min.
5 to 35˚C
Within 5 min.
/
/
/
/
/
/
10. Temperature cycle
Time:
30 min.
Cycles: 5
11. Salt spray test
No excessive corrosion
48 hours continuous exposure to 5% salt water
*V.S.W.R. Measurement System
The above V.S.W.R. standard values were measured using the measurement system of the diagram below.
NOTE 1: Cable type connectors were measured with SMA conversion adapters
attached to both ends of the harness product of a suitable 10-cm cable.
NOTE 2: Board type connectors were mounted to a 50Ω glass epoxy board and
measurements were conducted with SMA conversion adapters attached.
ꢀMaterials
Part
Material
Phosphor bronze
Brass
Finish
Silver plating
Gold plating
Gold plating
Black
Remarks
—————
—————
—————
UL94V-0
Shell
Male center contact
Phosphor bronze
Female center contact
Plug
Receptacle
PBT
LCP
Insulator
Beige
UL94V-0
2
ꢀPlugs
U.FL-LP-040
Form of Plug After Cable Wiring
U.FL-LP-066
Item
Form of Plug After Cable Wiring
Applicable Cable
HRS No.
Part No.
Weight (mg)
53.7/unit
RF-MF5010 Manufactured by Nissei Electric Co., Ltd.
CO-6F-SB-CX50 Manufactured by Hitachi Cable, Ltd.
F12B0074-B Manufactured by Junkosha Co., Ltd.
Right-angle plug shell
CL331-0451-2
U.FL-LP-040
(for
Ø 0.81 cable)
0.4DS-PBA Manufactured by Sumitomo Electric Industries, Ltd.
Right-angle receptacle
(for 1.13 cable)
RF-MF5016 Manufactured by Nissei Electric Co., Ltd.
A12B1054 Manufactured by Junkosha Co., Ltd.
CL331-0452-5
CL331-0452-5
U.FL-LP-066
U.FL-LP-066
59.1/unit
59.1/unit
Ø
Right-angle receptacle
(for 1.32 cable)
A12B0733 Manufactured by Junkosha Co., Ltd.
CO-6F-DSB-CX-50 Manufactured by Hitachi Cable, Ltd.
Ø
Please order plugs with the cable assembly specifications.
ꢀCable assembly
Dimension of U.FL Series assembly products should be made as indicated below.
Double-Ended Cable Assembly
Single-Ended Cable Assembly
ꢀCable assembly overall length standard tolerance
ꢀOrdering information
U.FL - [] LP - [] - A - (L)
Overall Length L (mm)
< <
Standard Tolerance (mm)
0035 L 0200
= =
04
08
q
w
e
r
<
0200<L=0500
U.FL
q
Series name
<
0500<L=1000
12
Blank: Single ended
2: Double ended
<
w Assembly type
1000<L=1000
1.5%
04 : For use with Ø 0.81 cable
Note: Shortest length L is 35 mm.
e
r
Cable type
Overall length (mm)
5016 : For use with
066 : For use with
Ø
Ø
1.13 cable
1.32 cable
Length L is expressed in mm units.
Part No. of Cable Assembly
CL No.
Description
321-1937-2-**
321-1998-7-**
321-2493-6-**
321-2492-3-**
321-2170-7-**
321-2573-3-**
U.FL-2LP-04-A-(L)
U.FL-LP-04-A-(L)
Dia. 0.81mm Double Ended Cable Assembly
Dia. 0.81mm Single Ended Cable Assembly
Dia. 1.13mm Double Ended Cable Assembly
Dia. 1.13mm Single Ended Cable Assembly
Dia. 1.32mm Double Ended Cable Assembly
Dia. 1.32mm Single Ended Cable Assembly
U.FL-2LP-5016-A-(L)
U.FL-LP-5016-A-(L)
U.FL-2LP-066-A-(L)
U.FL-LP-066-A-(L)
Please contact Hirose Sales Representative about cable length and cable end treatment.
3
ꢀReceptacles
NOTE 1: Receptacles of the (01) specification are sold by
the pack with 100 pieces per pack. Please order
in pack units.
Recommended PCB Footprints
NOTE 2: Receptacles of the (10) specification are sold by
the reel (which contains 2,500 pieces). Please
order in reel units.
NOTE 3: Permissible value for mold resin which gets onto
the center contact.
HRS No.
Part No.
Sales Quantity
Weight (mg)
15.7/unit
CL331-0471-0-01
CL331-0471-0-10
U.FL-R-SMT(01)
U.FL-R-SMT(10)
Pack sales (100 pieces per pack)
Reel sales (2,500 pieces per reel)
ꢀPackaging specifications
Embossed Carrier Tape dimensions
Unreeling direction
Reel dimensions
4
ꢀConversion adapter
ꢀSMA conversion adapter
(Coupling portion: U.FL side jack - SMA side plug)
NOTE: The U.FL side coupling portion has a weaker lock than
the regular product and, therefore, cannot be used for
purposes other than performance measurements.
HRS No.
Product No.
CL311-0300-2
HRMP-U.FLJ
ꢀSMA conversion adapter
(Coupling portion: U.FL side plug - SMA side jack)
NOTE: The U.FL side coupling portion has a weaker lock than
the regular product and, therefore, cannot be used for
purposes other than performance measurements.
HRS No.
Product No.
CL311-0301-5
HRMJ-U.FLP
ꢀInspection receptacle
This receptacle is used for inspecting the continuity,
withstand voltage, and other aspects of the harness
product.
NOTE: The U.FL side coupling portion does not have a lock
and, therefore, cannot be used for purposes other than
continuity and withstand voltage inspections.
HRS No.
Product No.
U.FL-R-1
CL331-0466-0
ꢀExtraction jig
This jig is used for extraction from a coupled condition.
NOTE: The extraction jig is the same one used with the
E.FL Series
HRS No.
Product No.
E.FL-LP-N
CL331-0441-9
5
ꢀUsage precautions
1. Plugs
1) To disconnect connectors, hook the end portion of E.FL-LP-N onto the connector cover and pull off vertically in the
direction of the connector coupling axis.
(1) Connection/
disconnection of
connectors
To remove the connector directly, hold the connector cover and pull off vertically in the direction of the connector
coupling axis. (Please exercise caution so as not to injure fingertips or nails.)
2) To couple the connectors, the coupling axes of both connectors are aligned and the connectors are inserted as
perpendicularly as possible. Do not attempt to insert on an extreme angle.
After the connectors are coupled, do not apply a load to the cable in excess of the values indicated in the diagram
below.
U.FL-LP-040
2N or less
(2) Permissible load on
the cable after
U.FL-R-SMT
4N or less
connector coupling.
2N or less
(3) Precautions
Please note that excessive twisting in the action of insertion or removal will cause damage.
2. Receptacles
Recommended temperature profile (reference)
(1) Recommended
temperature profile
(Reference)
1) The temperature indicates the printed circuit board surface temperature of the connector lead portion.
2) The reflow soldering method should be performed at a peak temperature of 240˚C or less at the surface of the
printed circuit board.
3) The temperature profile will change depending on conditions which include such factors as the size of the board,
the solder used, and the solder thickness.
(2) Recommended hand
soldering conditions
(Reference)
Soldering iron temperature: 350˚C
Soldering time: Within 5 seconds
(3) Recommended screen
thickness
0.15 mm
6
相关型号：
©2020 ICPDF网 联系我们和版权申明