FX10A120/12-S-SV121 [HRS]
0.5mm Pitch Connectors with Ground Plate for Board-to-Board Connections;型号: | FX10A120/12-S-SV121 |
厂家: | HRS |
描述: | 0.5mm Pitch Connectors with Ground Plate for Board-to-Board Connections |
文件: | 总7页 (文件大小:419K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
NEW
0.5mm Pitch Connectors with Ground Plate for Board-to-Board Connections
FX10 Series
Cross-Section of Mating
✽Features
1. Improved Transmission Efficiency Between
Boards
Transmission characteristics have been improved through
a design that fixes ground plates to both sides of the
header and receptacle.
2. 10 Signal:1 Ground Arrangement
Signal and ground are arranged in a ratio of 10:1 with the
ground plate SMT connected to the board. The ground
stability achieved serves to reduce noise.
3. Reinforced Fittings for Added Solder Weld
Strength
Reinforced fittings provide greater adhesion to the board,
protecting against peeling. The unique connector design
provides a connection between the fitting and the ground
plate for a stronger ground.
4. Suited to High-Density Applications
The signal contact pitch of 0.5 mm produces a smaller
connector utilizing less board area for mounting.
5. Board-To-Board Dimensions of 4mm and 5
mm Are Available
Stack Height
Receptacles
Headers
FX10# –✽S/✽–SV
Dimension H
4mm
FX10#–✽P/✽–SV1
FX10#–✽P/✽–SV1
5mm
Note: The thickness of the solder paste is not included in the stack height (dimension H).
✽Applications
Notebook computers, PDA, and other miniature electronic equipment.
2003.7
1
✽Product Specifications
Operating temperature range
Operating humidity range
-55 to 85ç
Relative humidity 95% or less
(No condensation)
-10 to +60ç (Note 2)
Rated current 0.3 A (Note 1)
Rated voltage 50 V AC
Storage temperature range
Storage humidity range
Rating
-40 to 70% (Note 2)
Item
Requirements
Conditions
1. Insulation resistance
2. Voltage proof
100 Mø or greater
Measured at 100 V DC
No flashover or breakdown
150 V AC applied for one minute
Measured at 100 mA
3. Contact resistance
60 mø or less
No electrical discontinuity for 1µs or greater
No damage, cracks, or parts looseness
No electrical discontinuity for 1µs or longer
No damage, cracks, or parts looseness
Contact resistance of 70 mø or less, insulation resistance of
100 Mø or greater, no damage, cracks, or parts looseness
Frequency: 10 to 55 Hz, amplitude of 0.75 mm in 3 directions, 10
cycles each
4. Vibration
5. Shock
2
Acceleration of 490 m/s , 11 ms duration, sine half-wave
waveform, for 3 cycles in the both directions of each of the 3 axes
6. Damp heat
(Steady state)
7. Rapid change of
temperature
Temperature of 40ç, humidity of 90 to 95%, duration 96 h
Contact resistance of 70 mø or less, insulation resistance of Temperature: -55ç ✽ 15 to 35ç ✽ 85ç ✽ 15 to 35ç
100 Mø or greater, no damage, cracks, or parts looseness Time: 30 min. ✽ 2 to 3 min. ✽ 30 min. ✽ 2 to 3 min. for 5 cycles
Contact resistance of 70 mø or less
50 times
8. Insertion/Withdrawal life
No damage, cracks, or parts looseness
9. Resistance to
soldering heat
Reflow: At the recommended temperature profile
No melting of resin portion which affects performance
Soldering iron temperature: 300ç·for 3 seconds
Note 1: Please contact us when connector application exceeds 0.3 A rated current.
Note 2: The term storage refers to an unused products prior to board mounting (including packing materials) that is being kept for a long period.
The operating temperature and humidity range are suited to the non-conducting condition following board assembly.
Note 3: The aforementioned specifications are representative of this series. For information on specific parts, confirm with Sales Office.
✽Materials
Part
Material
LCP resin
Process
Beige
Notes
Insulator
UL94V-0
Engagement Area: Gold plating of 0.1µm
Tenmination Area: Solder plating
Engagement Area: Gold plating of 0.1m
Termination Area: Flash plating
Solder plating
Header
Contacts
Phosphor bronze
Receptacle
Ground plate
Phosphor bronze
Phosphor bronze
Reinforced fitting
Tin plating
Note : The black dots on the insulater will not affect performance.
✽Product Number Configuration
Please use this information to discern the product specifications from the product number codes.
To order, please select from the product number codes listed in tables on pages 3 to 5 of this catalog.
-
-
FX 10 # ✽ P / ✽ SV 1 (✽✽✽)
1
2
3
5
6
7
8
4
1
2
3
6
7
Series name: FX
Series No.: 10
Form Symbol
Contact form
SV: Straight SMT
Product height
Blank: Standard
A: With guide post
B: Without guide post
Number of contacts
1 : Standard + 1mm
Packaging classification
Blank: Tray packaging
4
5
8
Signal/Ground: 80/8, 100/10, 120/12,
140/14
(21) : Embossed tape packaging
Connector type
P: Header
S: Receptacle
2
✽Receptacles
Unit: mm
Notes
Number of Contacts
HRS No.
Product No.
A
B
C
D
E
F
Signal Ground
CL570-0201-4-✽✽✽
CL570-0202-7-✽✽✽
CL570-0203-0-✽✽✽
CL570-0204-2-✽✽✽
CL570-0221-1-✽✽✽
CL570-0222-4-✽✽✽
CL570-0223-7-✽✽✽
CL570-0224-0-✽✽✽
FX10A-080S/08-SV(✽✽✽)
FX10A-100S/10-SV(✽✽✽)
FX10A-120S/12-SV(✽✽✽)
FX10A-140S/14-SV(✽✽✽)
FX10B-080S/08-SV(✽✽✽)
FX10B-100S/10-SV(✽✽✽)
FX10B-120S/12-SV(✽✽✽)
FX10B-140S/14-SV(✽✽✽)
080
100
120
140
080
100
120
140
08
10
12
14
08
10
12
14
23.5
29.5
35.5
41.5
23.5
29.5
35.5
41.5
18
24
30
36
18
24
30
36
31.1 26.4 31.5 28.3
37.1 32.4 37.5 34.3
43.1 38.4 43.5 40.3
49.1 44.4 49.5 46.3
With guideposts
Without guideposts
31.1
37.1
43.1
49.1
–
–
–
–
31.5 28.3
37.5 34.3
43.5 40.3
49.5 46.3
[Specifications number]- ✽✽✽,(✽✽✽)
Blank: Tray packaging
(21) :Embossed tape packaging
Note 1: There is no polarity in terms of board mounting for this product.
Note 2: The coplanarity of this product's SMT leads is 0.1 mm or less.
Note 3: Please order embossed tape packaged items by the reel. (One reel holds 1,000 pieces.)
B
Recommended Land Pattern Dimensions (Metal Mask Dimensions)
Recommended metal mask thickness: 0.15 mm
Note 1 Cross-hatched portions, totaling n places, indicate the ground circuits.
2 Cross-hatched portions, 2 places on both sides, indicate the reinforced fittings.
3 Not required in products without guideposts.
3
✽Headers
✽4mm Mounting Height
Unit: mm
Notes
Number of Contacts
HRS No.
Product No.
A
B
C
D
E
F
Signal Ground
✽✽✽
✽✽✽
✽✽✽
✽✽✽
✽✽✽
✽✽✽
✽✽✽
✽✽✽
✽✽✽
)
CL570-0001-5-
CL570-0002-8-
CL570-0003-0-
CL570-0004-3-
CL570-0021-2-
CL570-0022-5-
CL570-0023-8-
CL570-0024-0-
FX10A-080P/08-SV(
FX10A-100P/10-SV(
FX10A-120P/12-SV(
FX10A-140P/14-SV(
FX10B-080P/08-SV(
FX10B-100P/10-SV(
FX10B-120P/12-SV(
FX10B-140P/14-SV(
080
100
120
140
080
100
120
140
08
10
12
14
08
10
12
14
23.5
29.5
35.5
41.5
23.5
29.5
35.5
41.5
18
24
30
36
18
24
30
36
31.1 26.4 31.5 28.3
37.1 32.4 37.5 34.3
43.1 38.4 43.5 40.3
49.1 44.4 49.5 46.3
✽✽✽
)
With guideposts
Without guideposts
✽✽✽
)
✽✽✽
)
✽✽✽
)
31.1
37.1
43.1
49.1
-
-
-
-
31.5 28.3
37.5 34.3
43.5 40.3
49.5 46.3
✽✽✽
)
✽✽✽
)
✽✽✽
)
[Specifications number] -✽✽✽, (✽✽✽)
Blank: Tray packaging
(21) : Embossed tape packaging
Note 1: There is no polarity in terms of board mounting for this product.
Note 2: The coplanarity of this product's SMT leads is 0.1mm or less.
Note 3: Please order embossed tape packaged items by the reel. (One reel holds 1,000 pieces.)
B
Recommended Land Pattern Dimensions (Metal Mask Dimensions)
Recommended metal mask thickness: 0.15 mm
Note 1 Cross-hatched portions, totaling n places, indicate the ground circuits.
2 Cross-hatched portions, 2 places on both sides, indicate the reinforced fittings.
3 The cross-hatched area
inside the SMT land may come into contact with the connector contacts
and thus care should be taken that the pattern does not extend beyond the SMT land width.
Not required in products without guideposts.
4
4
✽Headers
✽5mm Mounting Height
Unit: mm
Notes
Number of Contacts
HRS No.
Product No.
A
B
C
D
E
F
Signal Ground
✽✽✽
✽✽✽
✽✽✽
✽✽✽
✽✽✽
✽✽✽
✽✽✽
✽✽✽
✽✽✽
)
CL570-0101-0-
CL570-0102-2-
CL570-0103-5-
CL570-0104-8-
CL570-0121-7-
CL570-0122-0-
CL570-0123-2-
CL570-0124-5-
FX10A-080P/08-SV1(
FX10A-100P/10-SV1(
FX10A-120P/12-SV1(
FX10A-140P/14-SV1(
FX10B-080P/08-SV1(
FX10B-100P/10-SV1(
FX10B-120P/12-SV1(
FX10B-140P/14-SV1(
080
100
120
140
080
100
120
140
08
10
12
14
08
10
12
14
23.5
29.5
35.5
41.5
23.5
29.5
35.5
41.5
18
24
30
36
18
24
30
36
31.1 26.4 31.5 28.3
37.1 32.4 37.5 34.3
43.1 38.4 43.5 40.3
49.1 44.4 49.5 46.3
✽✽✽
)
With guideposts
Without guideposts
✽✽✽
)
✽✽✽
)
✽✽✽
)
31.1
37.1
43.1
49.1
-
-
-
-
31.5 28.3
37.5 34.3
43.5 40.3
49.5 46.3
✽✽✽
)
✽✽✽
)
✽✽✽
)
[Specifications number] -✽✽✽,(✽✽✽)
Blank: Tray packaging
(21) : Embossed tape packaging
Note 1: There is no polarity in terms of board mounting for this product.
Note 2: The coplanarity of this product's SMT leads is 0.1 mm or less.
Note 3: Please order embossed tape packaged items by the reel. (One reel holds 1,000 pieces.)
B
Recommended Land Pattern Dimensions (Metal Mask Dimensions)
Recommended metal mask thickness: 0.15 mm
Note 1 Cross-hatched portions, totaling n places, indicate the ground circuits.
2 Cross-hatched portions, 2 places on both sides, indicate the reinforced fittings.
3 The cross-hatched area
inside the SMT land may come into contact with the connector contacts
and thus care should be taken that the pattern does not extend beyond the SMT land width.
4 Not required in products without guideposts.
5
BEmbossed Carrier Tape Dimensions
✽Receptacles
Insertion Connector
G
H
J
L
M
N
FX10#-080S/08-SV 20.2 40.4 44 330 45.5 50.5
FX10#-100S/10-SV 26.2 52.4 56 330 59 64
FX10#-120S/12-SV 26.2 52.4 56 330 59 64
FX10#-140S/14-SV 34.2 68.4 72 330 76.5 81.5
Note: There is no polarity in terms of embossed tape
packaging for this product.
✽Headers
Insertion Connector
G
H
J
K
L
M
N
FX10#-080P/08-SV 20.2 40.4 44 3.8 330 45.5 50.5
FX10#-100P/10-SV 26.2 52.4 56 3.8 330 59 64
FX10#-120P/12-SV 26.2 52.4 56 3.8 330 59 64
FX10#-140P/14-SV 34.2 68.4 72 3.8 330 76.5 81.5
FX10#-080P/08-SV1 20.2 40.4 44 4.8 370 45.5 50.5
FX10#-100P/10-SV1 26.2 52.4 56 4.8 370 59 64
FX10#-120P/12-SV1 26.2 52.4 56 4.8 370 59 64
FX10#-140P/14-SV1 34.2 68.4 72 4.8 370 76.5 81.5
Note: There is no polarity in terms of embossed tape
packaging for this product.
✽Reel Packaging Dimensions
6
BRecommended Temperature Profile
This temperature profile is a reference for the setting conditions described below. It will differ depending on conditions
and so mounting should follow verification.
Applicable Conditions
Reflow method
Solder
:
:
IR reflow
Cream type 63Sn/37Pb
(Flux component of 9wt%)
Glass epoxy. 85 x 110 x 1.6mm
0.15mm
Test substrate
:
:
Metal mask thickness
This temperature profile is a recommendation.
Conditions may change somewhat depending on the type
of cream solder and the amount.
BWashing Conditions
Organic Solvent Washing
Solvent
Room temperature washing Heated washing
IPA
Yes
Yes
Yes
Yes
(Isopropyl alcohol)
HCFC
(Hydrochlorofluorocarbon)
Water Type Washing
When using water type cleaning agents (e.g., terpene, and alkali saponifiers), select the cleaning agent based on the
documentation issued by the various manufacturers of cleaning agents which describes the effects on metals and resins.
Be careful that parts are not left with moisture remaining on them.
Washing Precautions
Residual flux or cleaning agent on the contacts when washing with organic solvents or water type cleaners can give rise to the
deterioration of electrical performance. In this regard it is important to check whether a thorough washing has been performed.
BConnector Handling Precautions
1. Allowable Creepage Dimensions at Time of Mating
The effective coupling length of this product is 1.1 mm for the signal portion and 1 mm for the ground portion. The creepage of
the header and receptacle at the time of mating should be within 0.5 mm of the completely coupled condition.
2. Retension of Boards
Avoid the support of boards by connectors alone and adopt a locking measure that does not rely on the connectors.
3. Solder Repair
Flux may rise as far as the contact portion of the connector depending on the flux coating and other factors at the time of repair.
This will cause poor contact reliability; therefore, before use, the aforementioned washing conditions should be taken into
consideration prior to connector washing.
4. Miscellaneous
·The shade of the molded items may vary somewhat depending on the manufacturing lot; however, this does not affect performance.
7
相关型号:
FX10B-100P/10-SV(71)
Board Stacking Connector, 110 Contact(s), 2 Row(s), Male, Straight, Surface Mount Terminal, ROHS COMPLIANT
HRS
FX10B-100P/10-SV(91)
Board Stacking Connector, 110 Contact(s), 2 Row(s), Male, Straight, Surface Mount Terminal, ROHS COMPLIANT
HRS
©2020 ICPDF网 联系我们和版权申明