FH34S-16S-0.5SH(50) [HRS]
Card Edge Connector, 16 Contact(s), 1 Row(s), Female, Right Angle, 0.02 inch Pitch, Surface Mount Terminal, Locking, Beige Insulator, ROHS COMPLIANT;
| 型号： | FH34S-16S-0.5SH(50) |
| 厂家： | 
HRS |
| 描述： | Card Edge Connector, 16 Contact(s), 1 Row(s), Female, Right Angle, 0.02 inch Pitch, Surface Mount Terminal, Locking, Beige Insulator, ROHS COMPLIANT PC 连接器 |
| 文件： | 总9页 (文件大小：318K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information.
All non-RoHS products have been discontinued, or will be discontinued soon. Please check the products status on the Hirose website RoHS search at www.hirose-connectors.com, or contact your Hirose sales representative.
NEW
0.5 mm Pitch, 1.0 mm above the board Top Contact, Back-Flip
actuator Flexible Printed Circuit & Flexible Flat Cable ZIF Connectors
FH34(S)Series
Increased FPC/FFC holding force
Space saving (30 pos. shown)
Actuator
Metal fittings
1.0mm
3.2mm
Easy FPC/FFC insertion
Back opening rotating
All four
sides are
chamfered.
Top contacts
■Features
1. Low-profile
With the 1.0 mm above the board and width of 3.8 mm the
connectors are used in space saving applications.
Ready to insert FPC/FFC
2. Increased FPC/FFC retention
Delivered with
the actuator open
As compared with existing similar construction connectors:
* In horizontal direction: Approximately 2.6 times
* In vertical direction: Approximately 2 times
3. Unique Back-Flip rotating actuator
The rotating actuator opens from the back of the connector,
assuring reliable electrical and mechanical connection.
4. Easy FPC/ FFC insertion
Entry chamfers at all sides of the FPC/FFC insertion slot assure
correct insertion and positioning of the FPC/FFC.
FPC
5. Delivered with the actuator open
FPC/FPC can be immediately inserted without the need for the
opening of the actuator.
FPC/FFC inserted and retained.
Completed electrical and mechanical connection.
6. Standard FPC/FFC thickness
Reliable connection with the use of ready available 0.3 mm thick
FFC/FPC.
7. Compatible with existing connectors.
FPC/FFC and PCB mounting patterns are the same as for the
FH19SC Series (bottom contact), allowing the use of both
connectors for interconnections between two boards or replacement
of the connectors.
8. Conductive traces on the PCB can run under
the connector
No exposed contacts on the bottom of the connector.
9. Board placement with automatic equipment
Flat top surface and packaging on the tape-and-reel allows use of
vacuum nozzles.
Standard reel contains 5,000 pieces.
Compatible with existing connectors.(FH19SC SERIES)
■Applications
Mobile phones, PDA’s, digital cameras, digital camcorders, camera
modules and other compact devices requiring Flexible Printed Circuit
connections using high reliability extremely small profile connectors.
2008.3
1
The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information.
All non-RoHS products have been discontinued, or will be discontinued soon. Please check the products status on the Hirose website RoHS search at www.hirose-connectors.com, or contact your Hirose sales representative.
( )
FH34 S Series●0.5 mm Pitch, 1.0 mm above the board Top Contact, Back-Flip actuator Flexible Printed Circuit & Flexible Flat Cable ZIF Connectors
■Specifications
Operating temperature range:
-55 to +85°C (Note 1)
Operating humidity range:
Storage temperature range:
-10 to +50°C (Note 2)
Storage humidity range:
Current rating 0.5 A
Ratings
Voltage rating 50 Vrms AC
Relative humidity 90% max. (No condensation)
Relative humidity 90% max. (No condensation)
Recommended FPC/FFC Thickness: 0.3 +/- 0.03 mm, Gold plated contact pads
Item
Specification
Conditions
1. Insulation resistance 500 Mø min.
100 V DC
2. Withstanding voltage
No flashover or insulation breakdown
100 mø max.
* Including FPC and FFC conductor resistance
250 Vrms AC / one minute
3. Contact resistance
1 mA, AC / DC 20mV max (AC: 1kHz)
Contact resistance: 100 mø max.
No damage, cracks, or parts dislocation
No electrical discontinuity of 1μs or longer
Contact resistance: 100 mø max.
No damage, cracks, or parts dislocation
4. Durability
5. Vibration
20 cycles
Frequency: 10 to 55 Hz, single amplitude of 0.75
mm, 10 cycles in each of the 3 axis
No electrical discontinuity of 1μs or longer
Contact resistance: 100 mø max.
No damage, cracks, or parts dislocation
Acceleration of 981m/s2, 6 ms duration, sine half-
wave, 3 cycles in each of the 3 axis
6. Shock
Contact resistance: 100 mø max.
Insulation resistance: 50 Mø min.
No damage, cracks, or parts dislocation
7. Humidity (Steady state)
96 hours at 40°C and humidity of 90 to 95%
Contact resistance: 100 mø max.
Insulation resistance: 50 Mø min.
No damage, cracks, or parts dislocation
Temperature : -55°C / +15°C to +35°C/+85°C / +15°C to +35°C
8. Temperature cycle
Time:
30
/
2 to 3
/
30
/ 2 to 3 minutes
5 cycles
Reflow: At the recommended temperature profile
Manual soldering: 350°C 5°C for 5 seconds (Note 3)
9. Resistance to soldering heat
No deformation of components affecting performance
Note1: Includes temperature rise caused by current flow.
Note2: The term "storage" refers to products stored for a long period prior to mounting and use.
The operating temperature and humidity range covers the non-conducting condition of installed connectors in storage, shipment or
during transportation after board mounting.
Note3: Small blisters of the molding compounds in small areas will not affect form, fit or function.
Note4: Information contained in this catalog represents general requirements for this Series.
Contact us for the drawings and specifications for a specific part number shown.
■Materials
Part
Material
Finish
Remarks
UL94V-0
Insulator
Actuator
LCP
PA
Color: Beige
Color: Black
Contacts
Metal fittings
Phosphor bronze
Phosphor bronze
Gold plating
Pure tin reflow plating
-------
-------
■Ordering information
FH34 S - 30S - 0.5 SH (50)
1
2
3
4
5
6
1 Series name
2 S
:FH34
:FPC/FFC 0.3 mm thick
5 Termination type :
SH
: SMT horizontal mounting type
3
4
Number of positions : 4, 8, 11, 14, 16, 22 26, 30, 32, 34 6 Plating specifications (50)…Gold plating with nickel barrier
Contact pitch : 0.5mm 5,000 pieces / reel
2
The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information.
All non-RoHS products have been discontinued, or will be discontinued soon. Please check the products status on the Hirose website RoHS search at www.hirose-connectors.com, or contact your Hirose sales representative.
( )
FH34 S Series●0.5 mm Pitch, 1.0 mm above the board Top Contact, Back-Flip actuator Flexible Printed Circuit & Flexible Flat Cable ZIF Connectors
■Connector Dimensions
A
B
H
∞Number of contacts
0.15 H
0.5
(0.15)
(3.8)
2.9
Polarizing mark indicator
Number of contacts indicator
A * *
Metal fittings (2x)
0.5
0.3
(0.15)
2.9
(C: FPC/FFC insertion slot dimension)
0.1
1
D
Note 1 : The coplanarity of each terminal lead is within 0.1.
Note 2 : Slight variations in color of the plastic compounds do not affect form ,fit or function of the connector.
All dimensions: mm
A
Part Number
CL No.
Number of Contacts
B
C
D
RoHS
4
04.0
05.0
06.0
06.5
07.5
08.0
09.0
10.0
12.0
13.0
14.0
15.0
16.0
17.0
18.0
19.0
01.5
02.5
03.5
04.0
05.0
05.5
06.5
07.5
09.5
10.5
11.5
12.5
13.5
14.5
15.5
16.5
02.53
03.53
04.53
05.03
06.03
06.53
07.53
08.57
10.57
11.57
12.57
13.57
14.57
15.57
16.57
17.57
03.38
04.38
05.38
05.88
06.88
07.38
08.38
09.38
11.38
12.38
13.38
14.38
15.38
16.38
17.38
18.38
FH34S-04S-0.5SH(50)
FH34S-06S-0.5SH(50)
FH34S-08S-0.5SH(50)
FH34S-09S-0.5SH(50)
FH34S-11S-0.5SH(50)
FH34S-12S-0.5SH(50)
FH34S-14S-0.5SH(50)
FH34S-16S-0.5SH(50)
FH34S-20S-0.5SH(50)
FH34S-22S-0.5SH(50)
FH34S-24S-0.5SH(50)
FH34S-26S-0.5SH(50)
FH34S-28S-0.5SH(50)
FH34S-30S-0.5SH(50)
FH34S-32S-0.5SH(50)
FH34S-34S-0.5SH(50)
580-1203-2-50
Reserved for product expansion
580-1204-5-50
6
8
Reserved for product expansion
580-1213-6-50
9
11
12
14
16
20
22
24
26
28
30
32
34
Reserved for product expansion
580-1206-0-50
580-1211-0-50
YES
Reserved for product expansion
580-1216-4-50
Reserved for product expansion
580-1212-3-50
Reserved for product expansion
580-1201-7-50
580-1208-6-50
580-1207-3-50
Tape and reel packaging (5,000 pieces/reel).
Order by number of reels.
3
The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information.
All non-RoHS products have been discontinued, or will be discontinued soon. Please check the products status on the Hirose website RoHS search at www.hirose-connectors.com, or contact your Hirose sales representative.
( )
FH34 S Series●0.5 mm Pitch, 1.0 mm above the board Top Contact, Back-Flip actuator Flexible Printed Circuit & Flexible Flat Cable ZIF Connectors
BRecommended PCB mounting pattern and metal mask dimensions
Recommended metal mask thickness: t=0.1
B
J
∞Number of contacts
0.5
0.3 0.05
0.1 J
0.25 0.03
(Metal mask)
(0.065)
(0.185)
E
F
0.1
0.1
(A)
BRecommended FPC/FFC Dimensions
G
B
0.05
0.03
0.5 0.07
0.5 0.03
0.3 0.03
0.3 0.03
*Polyimide and thermally hardening adhesive is recommended as the materials for the stiffener.
Note: When using the FPC/FFC in FH34S or FH19SC connectors, the exposed area inserted in either connector is 2.5mm
0.3mm and the stiffener is 3.5mm min.
All dimensions: mm
Part Number
CL No.
Number of Contacts
A
B
E
F
G
02.5
03.5
04.5
05.0
06.0
06.5
07.5
08.5
10.5
11.5
12.5
13.5
14.5
15.5
16.5
17.5
4
04.0
05.0
06.0
06.5
07.5
08.0
09.0
10.0
12.0
13.0
14.0
15.0
16.0
17.0
18.0
19.0
01.5
02.5
03.5
04.0
05.0
05.5
06.5
07.5
09.5
10.5
11.5
12.5
13.5
14.5
15.5
16.5
03.1
04.1
05.1
05.6
06.6
07.1
08.1
09.1
11.1
12.1
13.1
14.1
15.1
16.1
17.1
18.1
03.9
04.9
05.9
06.4
07.4
07.9
08.9
09.9
11.9
12.9
13.9
14.9
15.9
16.9
17.9
18.9
FH34S-04S-0.5SH(50)
FH34S-06S-0.5SH(50)
FH34S-08S-0.5SH(50)
FH34S-09S-0.5SH(50)
FH34S-11S-0.5SH(50)
FH34S-12S-0.5SH(50)
FH34S-14S-0.5SH(50)
FH34S-16S-0.5SH(50)
FH34S-20S-0.5SH(50)
FH34S-22S-0.5SH(50)
FH34S-24S-0.5SH(50)
FH34S-26S-0.5SH(50)
FH34S-28S-0.5SH(50)
FH34S-30S-0.5SH(50)
FH34S-32S-0.5SH(50)
FH34S-34S-0.5SH(50)
580-1203-2-50
Reserved for product expansion
580-1204-5-50
6
8
Reserved for product expansion
580-1213-6-50
9
11
12
14
16
20
22
24
26
28
30
32
34
Reserved for product expansion
580-1206-0-50
580-1211-0-50
Reserved for product expansion
580-1216-4-50
Reserved for product expansion
580-1212-3-50
Reserved for product expansion
580-1201-7-50
580-1208-6-50
580-1207-3-50
4
The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information.
All non-RoHS products have been discontinued, or will be discontinued soon. Please check the products status on the Hirose website RoHS search at www.hirose-connectors.com, or contact your Hirose sales representative.
( )
FH34 S Series●0.5 mm Pitch, 1.0 mm above the board Top Contact, Back-Flip actuator Flexible Printed Circuit & Flexible Flat Cable ZIF Connectors
BPackaging Specification
● Embossed Carrier Tape Dimensions
● Embossed Carrier Tape Dimensions
Tape width 24mm max.
Tape width of 32mm min.
(2.25)
(0.3)
4
0.1
2
0.15
8 0.1
(2.25)
(0.3)
1.5+0.1
(3.2)
(4)
Flat surface,
for placement with
automatic equipment
0
(1.95)
(1.95)
Unreeling direction
Flat surface, for placement
with automatic equipment
Unreeling direction
● Reel Dimensions
(Q: INSIDE)
(R: OUTSIDE)
End section
Mounting section
Lead section (400mm min.)
Embossed carrier tape
Top cover tape
No connector inserted
(10 pockets min.)
No connector inserted
(10 pockets min.)
All dimensions: mm
Part Number
CL No.
Number of Contacts
L
M
N
—
P
Q
R
580-1203-2-50
4
16
16
16
16
16
24
24
24
24
24
24
24
32
32
32
32
07.5
07.5
07.5
07.5
07.5
11.5
11.5
11.5
11.5
11.5
11.5
11.5
14.2
14.2
14.2
14.2
04.3
05.3
06.3
06.8
07.8
08.3
09.3
10.3
12.3
13.3
14.3
15.3
16.3
17.3
18.3
19.3
17.4
17.4
17.4
17.4
17.4
25.4
25.4
25.4
25.4
25.4
25.4
25.4
33.4
33.4
33.4
33.4
21.4
21.4
21.4
21.4
21.4
29.4
29.4
29.4
29.4
29.4
29.4
29.4
37.4
37.4
37.4
37.4
FH34S-04S-0.5SH(50)
FH34S-06S-0.5SH(50)
FH34S-08S-0.5SH(50)
FH34S-09S-0.5SH(50)
FH34S-11S-0.5SH(50)
FH34S-12S-0.5SH(50)
FH34S-14S-0.5SH(50)
FH34S-16S-0.5SH(50)
FH34S-20S-0.5SH(50)
FH34S-22S-0.5SH(50)
FH34S-24S-0.5SH(50)
FH34S-26S-0.5SH(50)
FH34S-28S-0.5SH(50)
FH34S-30S-0.5SH(50)
FH34S-32S-0.5SH(50)
FH34S-34S-0.5SH(50)
—
Reserved for product expansion
580-1204-5-50
6
—
8
—
Reserved for product expansion
580-1213-6-50
9
—
11
12
14
16
20
22
24
26
28
30
32
34
—
Reserved for product expansion
580-1206-0-50
—
—
580-1211-0-50
—
Reserved for product expansion
580-1216-4-50
—
—
Reserved for product expansion
580-1212-3-50
—
Reserved for product expansion
580-1201-7-50
28.4
28.4
28.4
28.4
580-1208-6-50
580-1207-3-50
Tape and reel packaging (5,000 pieces/reel).
5
The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information.
All non-RoHS products have been discontinued, or will be discontinued soon. Please check the products status on the Hirose website RoHS search at www.hirose-connectors.com, or contact your Hirose sales representative.
( )
FH34 S Series●0.5 mm Pitch, 1.0 mm above the board Top Contact, Back-Flip actuator Flexible Printed Circuit & Flexible Flat Cable ZIF Connectors
BTemperature Profile
● Using Lead-free Solder Paste
HRS test condition
MAX 250ç
Solder method
:
Reflow, IR/hot air
250
200
150
100
50
(Nihon Den-netsu Co., Ltd.'s Part Number:SENSBY NR-2)
: Room air
230ç
Environment
Solder composition : Paste, 96.5%Sn/3.0%Ag/0.5%Cu
(Senju Metal Industry, Co., Ltd.'s Part Number:
M705-221CM5-42-10.5)
200ç
Test board
:
:
:
Glass epoxy 25mm∞40mm∞0.8mm thick
0.3mm∞0.8mm
150ç
Land dimensions
Metal mask
0.25∞0.65∞0.1mm thick
The temperature profiles shown are based on the above conditions.
In individual applications the actual temperature may vary, depending
on solder paste type, volume / thickness and board size / thickness.
Consult your solder paste and equipment manufacturer for specific
recommendations.
25ç
(60 sec.)
(30 sec.)
Soldering
90 to 120 sec.
Preheating
0
Start
Time (Seconds)
6
The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information.
All non-RoHS products have been discontinued, or will be discontinued soon. Please check the products status on the Hirose website RoHS search at www.hirose-connectors.com, or contact your Hirose sales representative.
( )
FH34 S Series●0.5 mm Pitch, 1.0 mm above the board Top Contact, Back-Flip actuator Flexible Printed Circuit & Flexible Flat Cable ZIF Connectors
B
Recommended FPC construction
● Contact FPC manufacturer for specific details.
FPC : Flexible Printed Circuit
1. Using Single-sided FPC
Material Thickness
(μm)
Material Name
Covering film layer
Material
1 mil thick
Connecting side
Polyimide
25
25
Cover adhesive
0.2μm thick gold plated over 1
to 5μm thick nickel underplating
Surface treatment
3
Copper foil
Base adhesive
Base film
Cu
1oz
35
25
Polyimide
1 mil thick
25
Reinforcement material adhesive Thermosetting adhesive
35
Stiffener
Polyimide
Total
7 mil thick
175
298
Back side
FPC : Flexible Printed Circuit
2. Using Double-sided FPC
Material Thickness
(μm)
Material Name
Covering layer film
Material
Connecting side
Polyimide
1 mil thick
Cover adhesive
0.2μm thick gold plated over 1
to 5μm thick nickel underplating
Surface treatment
3
Through-hole copper
Copper foil
Cu
15
18
18
25
18
18
25
25
50
100
Cu
1/2oz
Base adhesive
Base film
Polyimide
Cu
1 mil thick
1/2oz
Base adhesive
Copper foil
Cover adhesive
Covering film layer
Reinforcement material adhesive
Stiffener
Polyimide
1 mil thick
Thermosetting adhesive
Polyimide
Total
4 mil thick
Back side
297
*
To prevent release of the FPC due to its bending, use of the double sided FPC with copper foil on the back side is NOT RECOMMENDED.
FFC : Flexible Flat Cable
3. Using FFC
Material Thickness
(μm)
Material Name
Polyester film
Material
Connecting side
12
30
Adhesive
Thermoplastic polyester
Polyester
Gold plated annealed copper foil
35
Adhesive
Polyester
Adhesive
Stiffener
30
12
Polyester
Polyester
Total
30
188
295
Note: Recommended FPC/FFC thickness: 0.3 0.03 mm
Back side
7
The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information.
All non-RoHS products have been discontinued, or will be discontinued soon. Please check the products status on the Hirose website RoHS search at www.hirose-connectors.com, or contact your Hirose sales representative.
( )
FH34 S Series●0.5 mm Pitch, 1.0 mm above the board Top Contact, Back-Flip actuator Flexible Printed Circuit & Flexible Flat Cable ZIF Connectors
BOperation and Precautions
Exercise care when handling connectors. Follow recommendations given below.
Operation
Precautions
1. As delivered
Delivered with the actuator
open. There is no need to
operate the actuator prior to
inserting the FPC/FFC.
• Do not close the actuator without the FPC/FPC inserted.
2. FPC/FFC insertion
• This connector is of the top contact specification.
The contacts are making connection with the FPC/FFC
pads from the top.
Do not insert the FPC/FFC with the pads facing down.
When inserting the FPC/FFC do not twist it. Insert
straight. Improper insertion may cause deformation of the
contacts and connection failures.
Insert the FPC/FFC with the
conductive surfaces facing
up.
Align the FPC/FFC straight
with the connector and insert
it firmly all the way.
FPC/FFC contact
surfaces face up.
• Be sure to insert the FPC/FFC when the actuator is fully
open.
3. Locking
• Do not operate the actuator by only one end. Open or
close by pushing at the center.
• Do not try to rotate the actuator past the fully open 90°
position. This will damage the connector, preventing it
from use.
After FPC/FFC insertion, rotate the actuator down to a
full stop, pushing it at the center.
• Do not apply excessive force to the connector when the
actuator is closed.
Push at the center of the actuator.
Rotate
4. FPC/FFC removal (Lock release)
• Do not operate the actuator from one end only.
• The actuator opens only 90°. Do not attempt to open it
past this angle or grasp it.
Carefully rotate the actuator up to 90°, lifting it at the
center.
• During the opening of the actuator do not press it toward
the connector body. Rotate up at the center.
Raise
Lift at the center
8
The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information.
All non-RoHS products have been discontinued, or will be discontinued soon. Please check the products status on the Hirose website RoHS search at www.hirose-connectors.com, or contact your Hirose sales representative.
( )
FH34 S Series●0.5 mm Pitch, 1.0 mm above the board Top Contact, Back-Flip actuator Flexible Printed Circuit & Flexible Flat Cable ZIF Connectors
BPrecautions at the Design Stage
(1) Route the FPC/FFC so that a direct pull force
(2) Make sure that there is enough space to insert/remove the FPC/FFC straight.
(3) Follow the recommendations given in this catalog in regard to mounting pattern, metal mask dimensions and FPC/FFC mating
dimensions.
(4) Consult the manufacturer of the FPC/FFC for the details on the flexibility of the specific FPC/FFC.
(5) When designing the board lay-out and spaces in the device assure that there is enough clearances for the actuator to fully
open/close.
BPrecautions when mounting connectors on the PCB
◆Handling before mounting on PCB
Insertion of the FPC/FFC or operation of the actuator prior to mounting on the PCB is NOT RECOMMENDED.
◆PC board warpage
Minimize the warpage as much as possible. The connector are straight within 0.1 mm max. Make sure that the mounting area
flatness can accept the connector terminals without causing any failure of the solder joints.
◆Forces on the board
◆When braking the large PC board into individual boards exercise care NOT to damage the installed connectors.
◆When attaching the boards or other components with the screws make sure that any stresses will NOT cause board deflections
affecting the mounting areas of the connector.
Connectors
PCB
◆When hand soldering:
· Do not perform hand soldering with the FPC inserted in the connector.
* Do not apply excessive heat or touch the soldering iron anywhere other than the connector leads.
* Do not use excessive amount of solder or flux compounds.
Operation of the actuator or contacts may be affected by excessive amounts of solder or flux compounds.
9
相关型号：
FH34S-16S-0.5SH50
0.5 mm Pitch, 1.0 mm above the board Top and Bottom Contact, Back-Flip actuator Flexible Printed Circuit & Flexible Flat Cable ZIF Connectors
HRS
FH34S-20S-0.5SH
0.5 mm Pitch, 1.0 mm above the board Top and Bottom Contact, Back-Flip actuator Flexible Printed Circuit & Flexible Flat Cable ZIF Connectors
HRS
FH34S-20S-0.5SH50
0.5 mm Pitch, 1.0 mm above the board Top and Bottom Contact, Back-Flip actuator Flexible Printed Circuit & Flexible Flat Cable ZIF Connectors
HRS
FH34S-22S-0.5SH
0.5 mm Pitch, 1.0 mm above the board Top and Bottom Contact, Back-Flip actuator Flexible Printed Circuit & Flexible Flat Cable ZIF Connectors
HRS
FH34S-22S-0.5SH50
0.5 mm Pitch, 1.0 mm above the board Top and Bottom Contact, Back-Flip actuator Flexible Printed Circuit & Flexible Flat Cable ZIF Connectors
HRS
FH34S-23S-0.5SH
0.5 mm Pitch, 1.0 mm above the board Top and Bottom Contact, Back-Flip actuator Flexible Printed Circuit & Flexible Flat Cable ZIF Connectors
HRS
FH34S-23S-0.5SH50
0.5 mm Pitch, 1.0 mm above the board Top and Bottom Contact, Back-Flip actuator Flexible Printed Circuit & Flexible Flat Cable ZIF Connectors
HRS
FH34S-24S-0.5SH
0.5 mm Pitch, 1.0 mm above the board Top and Bottom Contact, Back-Flip actuator Flexible Printed Circuit & Flexible Flat Cable ZIF Connectors
HRS
FH34S-24S-0.5SH50
0.5 mm Pitch, 1.0 mm above the board Top and Bottom Contact, Back-Flip actuator Flexible Printed Circuit & Flexible Flat Cable ZIF Connectors
HRS
FH34S-26S-0.5SH
0.5 mm Pitch, 1.0 mm above the board Top and Bottom Contact, Back-Flip actuator Flexible Printed Circuit & Flexible Flat Cable ZIF Connectors
HRS
FH34S-26S-0.5SH50
0.5 mm Pitch, 1.0 mm above the board Top and Bottom Contact, Back-Flip actuator Flexible Printed Circuit & Flexible Flat Cable ZIF Connectors
HRS
FH34S-30S-0.5SH
0.5 mm Pitch, 1.0 mm above the board Top and Bottom Contact, Back-Flip actuator Flexible Printed Circuit & Flexible Flat Cable ZIF Connectors
HRS
©2020 ICPDF网 联系我们和版权申明