RFM69HW-433S2 [HOPERF]
ISM TRANSCEIVER MODULE;型号: | RFM69HW-433S2 |
厂家: | HOPERF |
描述: | ISM TRANSCEIVER MODULE ISM频段 |
文件: | 总79页 (文件大小:1200K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
RFM69HW
RFM69HW ISM TRANSCEIVER MODULE V1.3
GENERAL DESCRIPTION
TAL
ND
The RFM69HW is a transceiver module capable of
operation over a wide frequency range, including the
315,433,868 and 915MHz license-free ISM (Industry
Scientific and Medical) frequency bands. All major RF
communication parameters are programmable and most of
them can be dynamically set. The RFM69HW offers
the unique advantage of programmable narrow-band and
wide- band communication modes. The RFM69HW is
optimized for low power consumption while offering high RF
output power and channelized operation. Compliance ETSI
and FCC regulations.
RFM69HW
In order to better use RFM69HW modules, this specification
also involves a large number of the parameters and
functions of its core chip RF69H's,including those IC pins
which are not leaded out. All of these can help customers
gain a better understanding of the performance of
RFM69HW modules, and enhance the application skills.
APPLICATIONS
Automated Meter Reading
Wireless Sensor Networks
Home and Building Automation
Wireless Alarm and Security Systems
Industrial Monitoring and Control
Wireless M-BUS
KEY PRODUCT FEATURES
+20 dBm - 100 mW Power Output Capability
High Sensitivity: down to -120 dBm at 1.2 kbps
High Selectivity: 16-tap FIR Channel Filter
80
Bullet-proof front end: IIP3 = -18 dBm, IIP2 = +35 dBm,
dB Blocking Immunity, no Image Frequency response
Low current: Rx = 16 mA, 100nA register retention
Programmable Pout: -18 to +20 dBm in 1dB steps
Constant RF performance over voltage range of module
FSK Bit rates up to 300 kb/s
Fully integrated synthesizer with a resolution of 61 Hz
FSK, GFSK, MSK, GMSK and OOK modulations
Built-in Bit Synchronizer performing Clock Recovery
Incoming Sync Word Recognition
115 dB+ Dynamic Range RSSI
Automatic RF Sense with ultra-fast AFC
Packet engine with CRC-16, AES-128, 66-byte FIFO
Built-in temperature sensor
Module Size:19.7X16mm
Page 1
Tel: +86-755-82973805 Fax: +86-755-82973550 E-mail: sales@hoperf.com http://www.hoperf.com
RFM69HW
Table of Contents
Page
1.
General Description ................................................................................................................................................
8
1.1. Simplified Block Diagram ............................................................................................................................. 8
1.2. Pin and Marking Diagram.................................................................................................................................
1.3. Pin Description ....................................................................................................................................10
9
2.
Electrical Characteristics........................................................................................................................................11
2.1. Absolute Maximum Ratings ..................................................................................................................11
2.2. Operating Range............................................................................................................................................ 11
2.3. Module Specification ...........................................................................................................................12
2.3.1. Power Consumption ................................................................................................................................. 12
2.3.2. Frequency Synthesis ................................................................................................................................ 12
2.3.3. Receiver .....................................................................................................................................................13
2.3.4. Transmitter ............................................................................................................................................... 14
2.3.5. Digital Specification ................................................................................................................................. 15
Module Description.................................................................................................................................................16
3.1. Power Supply Strategy.............................................................................................................................16
3.2. Frequency Synthesis..................................................................................................................................... 16
3.2.1. Reference Oscillator ................................................................................................................................. 16
3.2.2. CLKOUT Output ....................................................................................................................................... 17
3.2.3. PLL Architecture ....................................................................................................................................... 17
3.2.4. Lock Time ....................................................................................................................................................18
3.2.5. Lock Detect Indicator................................................................................................................................ 18
3.3. Transmitter Description .................................................................................................................................. 19
3.3.1. Architecture Description ........................................................................................................................... 19
3.3.2. Bit Rate Setting ........................................................................................................................................ 19
3.3.3. FSK Modulation ......................................................................................................................................... 20
3.3.4. OOK Modulation ....................................................................................................................................... 20
3.3.5. Modulation Shaping.................................................................................................................................... 21
3.3.6. Power Amplifiers ...................................................................................................................................... 21
3.3.7. High Power Settings ................................................................................................................................. 22
3.3.8. Output Power Summary ............................................................................................................................ 22
3.3.9. Over Current Protection ............................................................................................................................ 22
3.4. Receiver Description ..............................................................................................................................23
3.4.1. Block Diagram .......................................................................................................................................... 23
3.4.2. LNA - Single to Differential Buffer ............................................................................................................ 23
3.4.3. Automatic Gain Control ............................................................................................................................ 24
3.4.4. Continuous-Time DAGC........................................................................................................................... 25
3.4.5. Quadrature Mixer - ADCs - Decimators.................................................................................................... 26
3.4.6. Channel Filter ........................................................................................................................................... 26
3.4.7. DC Cancellation ....................................................................................................................................... 27
3.
Page 2
Tel: +86-755-82973805 Fax: +86-755-82973550 E-mail: sales@hoperf.com http://www.hoperf.com
RFM69HW
3.4.8. Complex Filter - OOK ............................................................................................................................... 27
3.4.9. RSSI......................................................................................................................................................... 27
3.4.10. Cordic ..................................................................................................................................................... 28
3.4.11. FSK Demodulator ....................................................................................................................................29
3.4.12. OOK Demodulator.................................................................................................................................. 29
3.4.13. Bit Synchronizer ..................................................................................................................................... 31
3.4.14. Frequency Error Indicator....................................................................................................................... 31
3.4.15. Automatic Frequency Correction............................................................................................................ 32
3.4.16. Optimized Setup for Low Modulation Index Systems............................................................................. 33
3.4.17. Temperature Sensor ............................................................................................................................... 34
3.4.18. Timeout Function.................................................................................................................................... 34
Operating Modes .................................................................................................................................................... 35
4.
4.1.
4.2.
Basic Modes.................................................................................................................................................. 35
Automatic Sequencer and Wake-Up Times.................................................................................................. 35
4.2.1. Transmitter Startup Time ..........................................................................................................................36
4.2.2. Tx Start Procedure ................................................................................................................................... 36
4.2.3. Receiver Startup Time.............................................................................................................................. 36
4.2.4. Rx Start Procedure................................................................................................................................... 38
4.2.5. Optimized Frequency Hopping Sequences.............................................................................................. 38
4.3. Listen Mode..................................................................................................................................................... 39
4.3.1. Timings..................................................................................................................................................... 39
4.3.2. Criteria...................................................................................................................................................... 40
4.3.3. End of Cycle Actions ................................................................................................................................ 40
4.3.4. Stopping Listen Mode............................................................................................................................... 41
4.3.5. RC Timer Accuracy .................................................................................................................................. 41
4.4. AutoModes...................................................................................................................................................... 42
Data Processing...................................................................................................................................................... 43
5.1. Overview ......................................................................................................................................................... 43
5.1.1. Block Diagram .......................................................................................................................................... 43
5.1.2. Data Operation Modes ............................................................................................................................. 43
5.2. Control Block Description.............................................................................................................................. 44
5.2.1. SPI Interface............................................................................................................................................... 44
5.2.2. FIFO ........................................................................................................................................................... 45
5.2.3. Sync Word Recognition............................................................................................................................ 46
5.2.4. Packet Handler......................................................................................................................................... 47
5.2.5. Control........................................................................................................................................................ 47
5.3. Digital IO Pins Mapping................................................................................................................................. 47
5.3.1. DIO Pins Mapping in Continuous Mode ................................................................................................... 48
5.3.2. DIO Pins Mapping in Packet Mode .......................................................................................................... 48
5.4. Continuous Mode ........................................................................................................................................... 49
5.4.1. General Description................................................................................................................................... 49
5.4.2. Tx Processing............................................................................................................................................ 49
5.
Page 3
Tel: +86-755-82973805 Fax: +86-755-82973550 E-mail: sales@hoperf.com http://www.hoperf.com
RFM69HW
5.4.3. Rx Processing .......................................................................................................................................... 50
5.5. Packet Mode .................................................................................................................................................. 50
5.5.1. General Description................................................................................................................................... 50
5.5.2. Packet Format .......................................................................................................................................... 51
5.5.3. Tx Processing (without AES).................................................................................................................... 53
5.5.4. Rx Processing (without AES) ................................................................................................................... 54
5.5.5. AES ........................................................................................................................................................... 54
5.5.6. Handling Large Packets ........................................................................................................................... 56
5.5.7. Packet Filtering.......................................................................................................................................... 56
5.5.8. DC-Free Data Mechanisms...................................................................................................................... 58
Configuration and Status Registers ...................................................................................................................... 60
6.1. General Description ...................................................................................................................................... 60
6.2. Common Configuration Registers................................................................................................................. 63
6.3. Transmitter Registers ..................................................................................................................................... 66
6.4. Receiver Registers......................................................................................................................................... 67
6.5. IRQ and Pin Mapping Registers.................................................................................................................... 69
6.6. Packet Engine Registers............................................................................................................................... 71
6.7. Temperature Sensor Registers..................................................................................................................... 74
6.8. Test Registers............................................................................................................................................... 74
Application Information ......................................................................................................................................... 75
7.1. Crystal Resonator Specification.................................................................................................................... 75
7.2. Reset of the Module ...................................................................................................................................... 75
7.2.1. POR.......................................................................................................................................................... .. 75
7.2.2. Manual Reset .............................................................................................................................................. 76
7.3. Reference Design ......................................................................................................................................... 77
Packaging Information .......................................................................................................................................... 78
8.1. Package Outline Drawing.............................................................................................................................. 78
Ordering Information ............................................................................................................................................. 79
6.
7.
8.
9.
Page 4
Tel: +86-755-82973805 Fax: +86-755-82973550 E-mail: sales@hoperf.com http://www.hoperf.com
RFM69HW
Index of Figures
Page
Figure 1. Block Diagram ................................................................................................................................................
8
Figure 2. Pin Diagram ....................................................................................................................................................
Figure 3. Marking Diagram ............................................................................................................................................
9
9
Figure 4. TCXO Connection ........................................................................................................................................ 16
Figure 5. Transmitter Block Diagram ........................................................................................................................... 19
Figure 6. Output Power Curves ................................................................................................................................... 22
Figure 7. Receiver Block Diagram ............................................................................................................................... 23
Figure 8. AGC Thresholds Settings ............................................................................................................................. 24
Figure 9. RSSI Dynamic Curve .................................................................................................................................... 28
Figure 10. Cordic Extraction ........................................................................................................................................ 28
Figure 11. OOK Peak Demodulator Description .......................................................................................................... 29
Figure 12. Floor Threshold Optimization ..................................................................................................................... 30
Figure 13. Bit Synchronizer Description ...................................................................................................................... 31
Figure 14. FEI Process ................................................................................................................................................ 32
Figure 15. Optimized AFC (AfcLowBetaOn=1) ............................................................................................................ 33
Figure 16. Temperature Sensor Response ................................................................................................................. 34
Figure 17. Tx Startup, FSK and OOK .......................................................................................................................... 36
Figure 18. Rx Startup - No AGC, no AFC .................................................................................................................... 37
Figure 19. Rx Startup - AGC, no AFC ......................................................................................................................... 37
Figure 20. Rx Startup - AGC and AFC ........................................................................................................................ 37
Figure 21. Listen Mode Sequence (no wanted signal is received) .............................................................................. 39
Figure 22. Listen Mode Sequence (wanted signal is received) ................................................................................... 41
Figure 23. Auto Modes of Packet Handler ................................................................................................................... 42
Figure 24. RFM69HW Data Processing Conceptual View ........................................................................................... 43
Figure 25. SPI Timing Diagram (single access) .......................................................................................................... 44
Figure 26. FIFO and Shift Register (SR) ..................................................................................................................... 45
Figure 27. FifoLevel IRQ Source Behavior .................................................................................................................. 46
Figure 28. Sync Word Recognition .............................................................................................................................. 47
Figure 29. Continuous Mode Conceptual View ........................................................................................................... 49
Figure 30. Tx Processing in Continuous Mode ............................................................................................................ 49
Figure 31. Rx Processing in Continuous Mode ........................................................................................................... 50
Figure 32. Packet Mode Conceptual View ................................................................................................................... 51
Figure 33. Fixed Length Packet Format ...................................................................................................................... 52
Figure 34. Variable Length Packet Format .................................................................................................................. 52
Figure 35. Unlimited Length Packet Format ................................................................................................................ 53
Figure 36. CRC Implementation .................................................................................................................................. 58
Figure 37. Manchester Encoding/Decoding ................................................................................................................. 58
Figure 38. Data Whitening ........................................................................................................................................... 59
Figure 39. POR Timing Diagram ................................................................................................................................. 75
Figure 40. Manual Reset Timing Diagram ................................................................................................................... 76
Page 5
Tel: +86-755-82973805 Fax: +86-755-82973550 E-mail: sales@hoperf.com http://www.hoperf.com
RFM69HW
Figure 41. +20dBm Schematic .................................................................................................................................... 77
Figure 42. Package Outline Drawing ........................................................................................................................... 78
Index of Tables
Page
Table 1. RFM69HW Pinouts ........................................................................................................................................ 10
Table 2. Absolute Maximum Ratings ............................................................................................................................ 11
Table 3. Operating Range ............................................................................................................................................ 11
Table 4. Power Consumption Specification .................................................................................................................. 12
Table 5. Frequency Synthesizer Specification .............................................................................................................. 12
Table 6. Receiver Specification .................................................................................................................................... 13
Table 7. Transmitter Specification ................................................................................................................................ 14
Table 8. Digital Specification ........................................................................................................................................ 15
Table 9. Bit Rate Examples .......................................................................................................................................... 20
Table 10. Power Amplifier Mode Selection Truth Table ............................................................................................... 21
Table 11. High Power Settings ..................................................................................................................................... 22
Table 12. LNA Gain Settings ........................................................................................................................................ 23
Table 13. Receiver Performance Summary .................................................................................................................. 25
Table 14. Available RxBw Settings ............................................................................................................................... 26
Table 15. Available DCC Cutoff Frequencies ............................................................................................................... 27
Table 16. Basic Transceiver Modes ............................................................................................................................. 35
Table 17. Range of Durations in Listen Mode .............................................................................................................. 39
Table 18. Signal Acceptance Criteria in Listen Mode ................................................................................................... 40
Table 19. End of Listen Cycle Actions .......................................................................................................................... 40
Table 20. Status of FIFO when Switching Between Different Modes of the Module ................................................... . 46
Table 21. DIO Mapping, Continuous Mode .................................................................................................................. 48
Table 22. DIO Mapping, Packet Mode ......................................................................................................................... 48
Table 23. Registers Summary ...................................................................................................................................... 60
Table 24. Common Configuration Registers ................................................................................................................. 63
Table 25. Transmitter Registers ................................................................................................................................... 66
Table 26. Receiver Registers ....................................................................................................................................... 67
Table 27. IRQ and Pin Mapping Registers ................................................................................................................... 69
Table 28. Packet Engine Registers .............................................................................................................................. 71
Table 29. Temperature Sensor Registers ..................................................................................................................... 74
Table 30. Test Registers .............................................................................................................................................. 74
Table 31. Crystal Specification ..................................................................................................................................... 75
Page 6
Tel: +86-755-82973805 Fax: +86-755-82973550 E-mail: sales@hoperf.com http://www.hoperf.com
RFM69HW
Acronyms
BOM
Bill Of Materials
Bit Rate
LSB
MSB
NRZ
OOK
Least Significant Bit
Most Significant Bit
Non Return to Zero
On Off Keying
BR
BW
Bandwidth
CCITT Comité Consultatif International
Téléphonique et Télégraphique - ITU
CRC
DAC
ETSI
Cyclic Redundancy Check
PA
Power Amplifier
Digital to Analog Converter
PCB
PLL
Printed Circuit Board
Phase-Locked Loop
European Telecommunications Standards
Institute
FCC
Fdev
FIFO
FIR
FS
Federal Communications Commission
POR
RBW
RF
Power On Reset
Frequency Deviation
Resolution BandWidth
Radio Frequency
First In First Out
Finite Impulse Response
Frequency Synthesizer
Frequency Shift Keying
Graphical User Interface
Integrated Circuit
RSSI
Rx
Received Signal Strength Indicator
Receiver
FSK
GUI
IC
SAW
SPI
SR
Surface Acoustic Wave
Serial Peripheral Interface
Shift Register
ID
IDentificator
Stby
Tx
Standby
IF
Intermediate Frequency
Interrupt ReQuest
Transmitter
IRQ
ITU
LFSR
LNA
LO
uC
Microcontroller
International Telecommunication Union
Linear Feedback Shift Register
Low Noise Amplifier
VCO
XO
Voltage Controlled Oscillator
Crystal Oscillator
eXclusive OR
XOR
Local Oscillator
Page 7
Tel: +86-755-82973805 Fax: +86-755-82973550 E-mail: sales@hoperf.com http://www.hoperf.com
RFM69HW
This product datasheet contains a detailed description of the RFM69HW performance and functionality.
1. General Description
The RFM69HW is a transceiver module ideally suited for today's high performance ISM band RF applications. It is
intended for use as high-performance, low-cost FSK and OOK RF transceiver for robust frequency agile, half-duplex bi-
directional RF links, and where stable and constant RF performance is required over the full operating range of the
device down to 1.8V.
The RFM69HW is intended for applications over a wide frequency range, including the 315MHz,433 MHz,868 MHz and
915MHz ISM bands. Coupled with a link budget in excess of 140 dB, the advanced system features of the RFM69HW
include a 66 byte TX/RX FIFO, configurable automatic packet handler, listen mode, temperature sensor and configurable
DIOs which greatly enhance system flexibility whilst at the same time significantly reducing MCU requirements.
The RFM69HW complies with both ETSI and FCC regulatory requirements and is available
1.1. Simplified Block Diagram
Figure 1. Block Diagram
Page 8
Tel: +86-755-82973805 Fax: +86-755-82973550 E-mail: sales@hoperf.com http://www.hoperf.com
RFM69HW
1.2. Pin and Marking Diagram
The following diagram shows the pin arrangement of the top view.
Figure 3. Marking Diagram
Page 9
Tel: +86-755-82973805 Fax: +86-755-82973550 E-mail: sales@hoperf.com http://www.hoperf.com
RFM69HW
1.3. Pin Description
Table 1 RFM69HW Pinouts
Number
Name
RESET
Type
Description
1
I/O
I/O
I/O
I/O
I/O
I/O
I/O
-
Reset trigger input
2
DIO0
DIO1
DIO2
DIO3
DIO4
DIO5
3.3V
GND
ANA
GND
SCK
MISO
MOSI
NSS
NC
Digital I/O, software configured
Digital I/O, software configured
Digital I/O, software configured
Digital I/O, software configured
Digital I/O, software configured
Digital I/O, software configured
Supply voltage
3
4
5
6
7
8
9
-
Ground
RF signal output/input.
10
11
12
13
14
15
16
-
I
Ground
SPI Clock input
SPI Data output
SPI Data input
O
I
I
SPI Chip select input
Connect to GND
-
Page 10
Tel: +86-755-82973805 Fax: +86-755-82973550 E-mail: sales@hoperf.com http://www.hoperf.com
RFM69HW
2. Electrical Characteristics
2.1. Absolute Maximum Ratings
Stresses above the values listed below may cause permanent device failure. Exposure to absolute
maximum ratings for extended periods may affect device reliability.
Table 2 Absolute Maximum Ratings
Symbol
VDDmr
Description
Min
Max
Unit
Supply Voltage
Temperature
-0.5
3.9
+115
+125
+6
V
Tmr
-55
° C
° C
dBm
%
Tj
Junction temperature
RF Input Level
-
-
-
-
Pmr
DC_20dBm
VSWR_20dBm
Duty Cycle of transmission at +20dBm output
Maximum VSWR at antenna port
1
3:1
-
2.2. Operating Range
Table 3 Operating Range
Symbol
Description
Min
Max
Unit
VDDop
Top
Supply voltage(1.8V-2.4V 17dBm, 2.4V- 3.6V 20dBm)
Operational temperature range
Load capacitance on digital ports
RF Input Level
1.8
-20
-
3.6
+70
25
V
°C
Clop
ML
pF
dBm
-
0
Page 11
Tel: +86-755-82973805 Fax: +86-755-82973550 E-mail: sales@hoperf.com http://www.hoperf.com
RFM69HW
2.3 Module Specification
The tables below give the electrical specifications of the transceiver under the following conditions: Supply voltage VBAT1=
VBAT2=VDD=3.3 V, temperature = 25 °C, FRF = 915 MHz, Pout = +20dBm, 2-level FSK modulation without pre-filtering,
FDA = 5 kHz, Bit Rate = 4.8 kb/s and terminated in a matched 50 Ohm impedance, unless otherwise specified.
Note Unless otherwise specified, the performances in the other frequency bands are similar or better.
2.3.1. Power Consumption
Table 4 Power Consumption Specification
Symbol
Description
Conditions
Min
Typ
Max
Unit
uA
Supply current in Sleep mode
Supply current in Idle mode
Supply current in Standby mode
-
-
-
-
0.1
1.2
1.25
9
1
-
IDDSL
IDDIDLE
IDDST
IDDFS
RC oscillator enabled
uA
Crystal oscillator enabled
1.5
-
mA
mA
Supply current in Synthesizer
mode
IDDR
IDDT
Supply current in Receive mode
-
16
-
mA
Supply current in Transmit mode
with appropriate matching, sta-
ble across VDD range
RFOP = +20 dBm, on PA_BOOST
RFOP = +17 dBm, on PA_BOOST
RFOP = +13 dBm, on RFIO pin
RFOP = +10 dBm, on RFIO pin
RFOP = 0 dBm, on RFIO pin
RFOP = -1 dBm, on RFIO pin
-
-
-
-
-
-
130
95
45
33
20
16
-
-
-
-
-
-
mA
mA
mA
mA
mA
mA
2.3.2. Frequency Synthesis
Table 5 Frequency Synthesizer Specification
Symbol
Description
Conditions
Min
Typ
Max
Unit
315MHz Module
433MHz Module
868MHz Module
FR
Synthesizer Frequency Range
290
424
862
890
340
510
890
MHz
MHz
MHz
MHz
1020
915MHz Module
For All Module
FXOSC
Crystal oscillator frequency
-
32
-
MHz
TS_OSC
Crystal oscillator wake-up time
-
250
500
us
TS_FS
Frequency synthesizer wake-up
time to PllLock signal
From Standby mode
-
80
150
us
TS_HOP
Frequency synthesizer hop time
at most 10 kHz away from the
target
-
-
-
-
-
-
-
20
20
50
50
80
80
80
-
-
-
-
-
-
-
us
us
us
us
us
us
us
200 kHz step
1 MHz step
5 MHz step
7 MHz step
12 MHz step
20 MHz step
25 MHz step
Page 12
Tel: +86-755-82973805 Fax: +86-755-82973550 E-mail: sales@hoperf.com http://www.hoperf.com
RFM69HW
19
Frequency synthesizer step
-
61.0
-
FSTEP
Hz
FSTEP = FXOSC/2
After calibration
Programmable
Programmable
Programmable
FRC
BRF
BRO
FDA
RC Oscillator frequency
Bit rate, FSK
-
62.5
-
kHz
1.2
1.2
0.6
-
-
-
300
kbps
kbps
kHz
Bit rate, OOK
32.768
300
Frequency deviation, FSK
FDA + BRF/2 =< 500 kHz
2.3.3. Receiver
All receiver tests are performed with RxBw = 10 kHz (Single Side Bandwidth) as programmed in RegRxBw, receiving a
PN15 sequence with a BER of 0.1% (Bit Synchronizer is enabled), unless otherwise specified. The LNA impedance is set
to 200 Ohms, by setting bit LnaZin in RegLna to 1. Blocking tests are performed with an unmodulated interferer. The
wanted signal power for the Blocking Immunity, ACR, IIP2, IIP3 and AMR tests is set 3 dB above the nominal sensitivity
level.
Table 6 Receiver Specification
Symbol
Description
Conditions
Min
Typ
Max
Unit
RFS_F
FSK sensitivity, highest LNA gain
-
-
-
-118
-114
-105
-
-
-
dBm
dBm
dBm
FDA = 5 kHz, BR = 1.2 kb/s
FDA = 5 kHz, BR = 4.8 kb/s
FDA = 40 kHz, BR = 38.4 kb/s
-
-
-120
-112
-
dBm
dBm
FDA = 5 kHz, BR = 1.2 kb/s *
BR = 4.8 kb/s
RFS_O
OOK sensitivity, highest LNA gain
-109
CCR
ACR
Co-Channel Rejection
-13
-10
-
dB
Adjacent Channel Rejection
-
37
42
42
-
-
dB
dB
Offset = +/- 25 kHz
Offset = +/- 50 kHz
BI
Blocking Immunity
-
-
-
66
71
79
-
-
-
dB
dB
dB
Offset = +/- 1 MHz
Offset = +/- 2 MHz
Offset = +/- 10 MHz
Blocking Immunity
Wanted signal at sensitivity
+16dB
-
-
-
62
65
73
-
-
-
dB
dB
dB
Offset = +/- 1 MHz
Offset = +/- 2 MHz
Offset = +/- 10 MHz
AMR
IIP2
AM Rejection , AM modulated
interferer with 100% modulation
depth, fm = 1 kHz, square
-
-
-
66
71
79
-
-
-
dB
dB
dB
Offset = +/- 1 MHz
Offset = +/- 2 MHz
Offset = +/- 10 MHz
2nd order Input Intercept Point
Unwanted tones are 20 MHz
above the LO
-
-
+75
+35
-
-
dBm
dBm
Lowest LNA gain
Highest LNA gain
Page 13
Tel: +86-755-82973805 Fax: +86-755-82973550 E-mail: sales@hoperf.com http://www.hoperf.com
RFM69HW
3rd order Input Intercept point
Unwanted tones are 1MHz and
1.995 MHz above the LO
-
+20
-18
-
-
IIP3
dBm
dBm
Lowest LNA gain
Highest LNA gain
-23
BW_SSB
IMR_OOK
TS_RE
Single Side channel filter BW
Image rejection in OOK mode
Programmable
2.6
27
-
500
-
kHz
dB
Wanted signal level = -106 dBm
30
Receiver wake-up time, from PLL
locked state to RxReady
-
-
1.7
96
-
-
ms
us
RxBw = 10 kHz, BR = 4.8 kb/s
RxBw = 200 kHz, BR = 100 kb/s
TS_RE_AGC Receiver wake-up time, from PLL
locked state, AGC enabled
-
3.0
163
ms
us
RxBw = 10 kHz, BR = 4.8 kb/s
RxBw = 200 kHz, BR = 100 kb/s
TS_RE_AGC Receiver wake-up time, from PLL
4.8
265
ms
us
RxBw = 10 kHz, BR = 4.8 kb/s
RxBw = 200 kHz, BR = 100 kb/s
&AFC
lock state, AGC and AFC enabled
TS_FEI
TS_AFC
TS_RSSI
DR_RSSI
FEI sampling time
Receiver is ready
Receiver is ready
Receiver is ready
AGC enabled
-
-
-
4.T
4.T
2.T
-
-
-
-
-
-
bit
bit
bit
AFC Response Time
RSSI Response Time
RSSI Dynamic Range
Min
Max
-
-
-115
0
-
-
dBm
dBm
*
Set SensitivityBoost in RegTestLna to 0x2D to reduce the noise floor in the receiver
2.3.4. Transmitter
Table 7 Transmitter Specification
Symbol
Description
Conditions
Min
Typ
Max
Unit
RF_OP
RF output power in 50 ohms
On RFIO pin
Programmable with 1dB steps Max
Min
-
-
+20
-18
-
-
dBm
dBm
RF_OPH
Max RF output power, on
PA_BOOST pin
With external match to 50 ohms
-
+20
-
dBm
RF output power stability
Transmitter Phase Noise
From VDD=2.4V to 3.6V
-
+/-0.3
-
dB
ΔRF_OP
PHN
50 kHz Offset from carrier
868 / 915 MHz bands
434 / 315 MHz bands
-
-
-95
-99
-
-
dBc/
Hz
ACP
Transmitter adjacent channel
power (measured at 25 kHz off-
set)
BT=0.5 . Measurement conditions as
defined by EN 300 220-1 V2.1.1
-
-
-37
dBm
TS_TR
Transmitter wake up time, to the
first rising edge of DCLK
Frequency Synthesizer enabled,
PaRamp = 10 us, BR = 4.8 kb/s.
-
120
-
us
Page 14
Tel: +86-755-82973805 Fax: +86-755-82973550 E-mail: sales@hoperf.com http://www.hoperf.com
RFM69HW
2.3.5. Digital Specification
Conditions: Temp = 25°C, VDD = 3.3V, unless otherwise specified.
Table 8 Digital Specification
Symbol
Description
Conditions
Min
Typ
Max
Unit
V
Digital input level high
Digital input level low
0.8
-
-
-
-
VDD
VDD
IH
V
V
V
0.2
IL
Digital output level high
Digital output level low
SCK frequency
SCK high time
Imax = 1 mA
Imax = -1 mA
0.9
-
-
-
-
0.1
10
-
VDD
VDD
MHz
ns
OH
OL
SCK
F
-
-
t
t
t
t
t
50
50
-
-
ch
SCK low time
-
-
ns
cl
SCK rise time
5
5
-
-
ns
rise
fall
SCK fall time
-
-
ns
MOSI setup time
from MOSI change to SCK rising
edge
30
-
ns
setup
t
t
t
t
MOSI hold time
NSS setup time
NSS hold time
from SCK rising edge to MOSI
change
60
30
-
-
-
-
-
-
-
-
-
-
ns
ns
ns
ns
ns
hold
from NSS falling edge to SCK rising
edge
nsetup
nhold
nhigh
from SCK falling edge to NSS rising
edge, normal mode
30
NSS high time between SPI
accesses
20
T_DATA
DATA hold and setup time
250
Page 15
Tel: +86-755-82973805 Fax: +86-755-82973550 E-mail: sales@hoperf.com http://www.hoperf.com
RFM69HW
3. Module Description
This section describes in depth the architecture of the RFM69HW low-power, highly integrated
transceiver.
3.1. Power Supply Strategy
The RFM69HW employs an advanced power supply scheme, which provides stable operating characteristics over the
full temperature and voltage range of operation. This includes the full output power of +20dBm maintained from 2.4 to 3.6V.
The RFM69HW can be powered from any low-noise voltage source via pins VBAT1 and VBAT2. Decoupling capacitors
should be connected, as suggested in the reference design, on VR_PA, VR_DIG and VR_ANA pins to ensure a correct
operation of the built-in voltage regulators.
3.2. Frequency Synthesis
The LO generation on the RFM69HW is based on a state-of-the-art fractional-N PLL. The PLL is fully integrated with
automatic calibration.
3.2.1. Reference Oscillator
The crystal oscillator is the main timing reference of the RFM69HW. It is used as a reference for the frequency
synthesizer and as a clock for the digital processing.
The XO startup time, TS_OSC, depends on the actual XTAL being connected on pins XTA and XTB. When using the built-
in sequencer, the RFM69HW optimizes the startup time and automatically triggers the PLL when the XO signal is stable.
To manually control the startup time, the user should either wait for TS_OSC max, or monitor the signal CLKOUT which
will only be made available on the output buffer when a stable XO oscillation is achieved.
An external clock can be used to replace the crystal oscillator, for instance a tight tolerance TCXO. To do so, bit 4 at
address 0x59 should be set to 1, and the external clock has to be provided on XTA. XTB should be left open. The peak-
peak amplitude of the input signal must never exceed 2.4 V. Please consult your TCXO supplier for an appropriate value
of decoupling capacitor, CD.
XTA
XTB
NC
TCXO
OP
32 MHz
Vcc
Vcc
GND
CD
Figure 4. TCXO Connection
Page 16
Tel: +86-755-82973805 Fax: +86-755-82973550 E-mail: sales@hoperf.com http://www.hoperf.com
RFM69HW
3.2.2. CLKOUT Output
The reference frequency, or a fraction of it, can be provided on DIO5 by modifying bits ClkOut in RegDioMapping2. Two
typical applications of the CLKOUT output include:
To provide a clock output for a companion processor, thus saving the cost of an additional oscillator. CLKOUT can be
made available in any operation mode except Sleep mode and is automatically enabled at power on reset.
To provide an oscillator reference output. Measurement of the CLKOUT signal enables simple software trimming of the
initial crystal tolerance.
Note to minimize the current consumption of the RFM69HW, please ensure that the CLKOUT signal is disabled when
not required.
3.2.3. PLL Architecture
The frequency synthesizer generating the LO frequency for both the receiver and the transmitter is a fractional-N sigma-
delta PLL. The PLL incorporates a third order loop capable of fast auto-calibration, and it has a fast switching-time. The
VCO and the loop filter are both fully integrated, removing the need for an external tight-tolerance, high-Q inductor in the
VCO tank circuit.
3.2.3.1. VCO
The VCO runs at 2, 4 or 6 times the RF frequency (respectively in the 915, 434 and 315 MHz bands) to reduce any LO
leakage in receiver mode, to improve the quadrature precision of the receiver, and to reduce the pulling effects on the VCO
during transmission.
The VCO calibration is fully automated. A coarse adjustment is carried out at power on reset, and a fine tuning is
performed each time the RFM69HW PLL is activated. Automatic calibration times are fully transparent to the end-user, as
their processing time is included in the TS_TE and TS_RE specifications.
3.2.3.2. PLL Bandwidth
The bandwidth of the RFM69HW Fractional-N PLL is wide enough to allow
for:
High speed FSK modulation, up to 300 kb/s, inside the PLL bandwidth
Very fast PLL lock times, enabling both short startup and fast hop times required for frequency agile applications
3.2.3.3. Carrier Frequency and Resolution
The RFM69HW PLL embeds a 19-bit sigma-delta modulator and its frequency resolution, constant over the whole
frequency range, and is given by:
FXOS
C
----------------
219
FSTE
=
P
The carrier frequency is programmed through RegFrf, split across addresses 0x07 to 0x09:
FRF = FSTEP
⋅Frf(23,0)
Note The Frf setting is split across 3 bytes. A change in the center frequency will only be taken into account when the
least significant byte FrfLsb in RegFrfLsb is written. This allows for more complex modulation schemes such as m-
ary FSK, where frequency modulation is achieved by changing the programmed RF frequency.
Page 17
Tel: +86-755-82973805 Fax: +86-755-82973550 E-mail: sales@hoperf.com http://www.hoperf.com
RFM69HW
3.2.4. Lock Time
PLL lock time TS_FS is a function of a number of technical factors, such as synthesized frequency, frequency step, etc.
When using the built-in sequencer, the RFM69HW optimizes the startup time and automatically starts the receiver or the
transmitter when the PLL has locked. To manually control the startup time, the user should either wait for TS_FS max given
in the specification, or monitor the signal PLL lock detect indicator, which is set when the PLL has is within its locking
range.
When performing an AFC, which usually corrects very small frequency errors, the PLL response time is approximately:
------------
In a frequency hopping scheme, the timings TS_HOP given in the table of specifications give an order of magnitude for the
expected lock times.
3.2.5. Lock Detect Indicator
A lock indication signal can be made available on some of the DIO pins, and is toggled high when the PLL reaches its
locking range. Please refer to Table 21 and Table 22 to map this interrupt to the desired pins.
Note The lock detect block may indicate an unlock condition (signal toggling low) when the transmitter is FSK modulated
with large frequency deviation settings.
Page 18
Tel: +86-755-82973805 Fax: +86-755-82973550 E-mail: sales@hoperf.com http://www.hoperf.com
RFM69HW
3.3. Transmitter Description
The transmitter of RFM69HW comprises the frequency synthesizer, modulator and power amplifier blocks.
3.3.1. Architecture Description
LNA
Receiver Chain
RFIO
PA0
Local
Oscillator
PA1
PA2
PA_BOOST
Figure 5. Transmitter Block Diagram
3.3.2. Bit Rate Setting
When using the RFM69HW in Continuous mode, the data stream to be transmitted can be input directly to the modulator
via pin DIO2/DATA in an asynchronous manner, unless Gaussian filtering is used, in which case the DCLK signal on pin
DIO1/DCLK is used to synchronize the data stream. See section 3.3.5 for details on the Gaussian filter.
In Packet mode or in Continuous mode with Gaussian filtering enabled (refer to section 5.5 for details), the Bit Rate (BR) is
controlled by bits BitRate in RegBitrate:
FXOS
C
-------------------
BR =
BitRate
Amongst others, the following Bit Rates are accessible:
Page 19
Tel: +86-755-82973805 Fax: +86-755-82973550 E-mail: sales@hoperf.com http://www.hoperf.com
RFM69HW
Table 9 Bit Rate Examples
BitRate
(15:8)
BitRate
(7:0)
(G)FSK
(G)MSK
Actual BR
(b/s)
Type
OOK
Classical modem baud rates
(multiples of 1.2 kbps)
0x68
0x34
0x1A
0x0D
0x06
0x03
0x01
0x00
0x02
0x01
0x0A
0x05
0x02
0x01
0x00
0x00
0x00
0x00
0x03
0x2B
0x15
0x0B
0x05
0x83
0x41
0xA1
0xD0
0x2C
0x16
0x00
0x00
0x80
0x40
0xD5
0xA0
0x80
0x6B
0xD1
1.2 kbps
2.4 kbps
1.2 kbps
2.4 kbps
4.8 kbps
9.6 kbps
19.2 kbps
1200.015
2400.060
4799.760
9600.960
19196.16
38415.36
76738.60
153846.1
57553.95
115107.9
12500.00
25000.00
50000.00
100000.0
150234.7
200000.0
250000.0
299065.4
32753.32
4.8 kbps
9.6 kbps
19.2 kbps
38.4 kbps
76.8 kbps
153.6 kbps
57.6 kbps
115.2 kbps
12.5 kbps
25 kbps
Classical modem baud rates
(multiples of 0.9 kbps)
Round bit rates
(multiples of 12.5, 25 and
50 kbps)
12.5 kbps
25 kbps
50 kbps
100 kbps
150 kbps
200 kbps
250 kbps
300 kbps
32.768 kbps
Watch Xtal frequency
32.768 kbps
3.3.3. FSK Modulation
FSK modulation is performed inside the PLL bandwidth, by changing the fractional divider ratio in the feedback loop of the
PLL. The large resolution of the sigma-delta modulator, allows for very narrow frequency deviation. The frequency
deviation FDEV is given by:
Note no constraint applies to the modulation index of the transmitter, but the frequency deviation must exceed 600 Hz.
3.3.4. OOK Modulation
OOK modulation is applied by switching on and off the Power Amplifier. Digital control and smoothing are available to
improve the transient power response of the OOK transmitter.
Page 20
Tel: +86-755-82973805 Fax: +86-755-82973550 E-mail: sales@hoperf.com http://www.hoperf.com
RFM69HW
3.3.5. Modulation Shaping
Modulation shaping can be applied in both OOK and FSK modulation modes, to improve the narrowband response of the
transmitter. Both shaping features are controlled with PaRamp bits in RegPaRamp.
In FSK mode, a Gaussian filter with BT = 0.3, 0.5 or 1 is used to filter the modulation stream, at the input of the
delta modulator. If the Gaussian filter is enabled when the RFM69HW is in Continuous mode, DCLK signal
sigma-
on pin DIO1/DCLK will trigger an interrupt on the uC each time a new bit has to be transmitted. Please refer to
section 5.4.2 for details.
When OOK modulation is used, the PA bias voltages are ramped up and down smoothly when the PA is turned on
off, to reduce spectral splatter.
and
Note the transmitter must be restarted if the PaRamp setting is changed, in order to recalibrate the built-in filter.
3.3.6. Power Amplifiers
A higher power mode, when PA1 and PA2 are combined, providing up to +20 dBm to a matched load.
When PA1 and PA2 are combined to deliver +20 dBm to the antenna, a specific impedance matching / harmonic filtering
design is required to ensure impedance transformation and regulatory compliance.
All PA settings are controlled by RegPaLevel, and the truth table of settings is given in Table 10.
Table 10 Power Amplifier Mode Selection Truth Table
Pa0On
Pa1On Pa2On
Mode
Power Range
Pout Formula
PA0 output on pin RFIO
-18 to +13 dBm
-18 dBm + OutputPower
1
0
0
1
1
1
0
0
1
1
PA1 enabled on pin PA_BOOST
-2 to +13 dBm
+2 to +17 dBm
+5 to +20 dBm
-18 dBm + OutputPower
-14 dBm + OutputPower
-11 dBm + OutputPower
0
0
PA1 and PA2 combined on pin PA_BOOST
PA1+PA2 on PA_BOOST with high output
power +20dBm settings (see 3.3.7)
Other combinations
Reserved
Notes - To ensure correct operation at the highest power levels, please make sure to adjust the Over Current Protection
Limit accordingly in RegOcp, except above +18dBm where it must be disabled
- If PA_BOOST pin is not used (+20dBm applications and less), the pin can be left floating.
Page 21
Tel: +86-755-82973805 Fax: +86-755-82973550 E-mail: sales@hoperf.com http://www.hoperf.com
RFM69HW
3.3.7. High Power Settings
The RFM69HW has a high power +20 dBm capability on PA_BOOST pin, with the following settings:
Table 11 High Power Settings
Value for
High Power
Value for Rx
or PA0 use
Register
Address
Description
OCP control
RegOcp
0x13
0x5A
0x5C
0x0F
0x5D
0x7C
0x1x
0x55
0x70
High power PA control
High power PA control
RegTestPa1
RegTestPa2
Note High Power settings MUST be turned off when using PA0, and in Receive mode
The Duty Cycle of transmission at +20dBm is limited to 1%, with a maximum VSWR of 3:1 at antenna port, over the
standard operating range [-40;+85°C].
3.3.8. Output Power Summary
The curves below summarize the possible PA options on the RFM69HW:
Pout vs.
P
r
ogram med Power
22
18
14
10
6
2
-2
Pout on PA0 [dBm]
Pout on PA1 [dBm]
Pout on PA1+PA2 [dBm]
-6
-10
-14
-18
-22
P
out on PA1+PA2 with 20dB m settings [dB m]
-18
-14
-10
-6
-2
Program m
2
6
10
14
18
e
d Pow er [dBm ]
Figure 6. Output Power Curves
3.3.9. Over Current Protection
An over current protection block is built-in the module. It helps preventing surge currents required when the transmitter is
used at its highest power levels, thus protecting the battery that may power the application. The current clamping value is
controlled by OcpTrim bits in RegOcp, and is calculated with the following formula:
Imax = 45 + 5
⋅OcpTrim mA
Note Imax sets a limit on the current drain of the Power Amplifier only, hence the maximum current drain of the
RFM69HW is equal to Imax + IFS
Page 22
Tel: +86-755-82973805 Fax: +86-755-82973550 E-mail: sales@hoperf.com http://www.hoperf.com
RFM69HW
3.4. Receiver Description
The RFM69HW features a digital receiver with the analog to digital conversion process being performed directly following
the LNA-Mixers block. The zero-IF receiver is able to handle (G)FSK and (G)MSK modulation. ASK and OOK modulation
is, however, demodulated by a low-IF architecture. All the filtering, demodulation, gain control, synchronization and packet
handling is performed digitally, which allows a very wide range of bit rates and frequency deviations to be selected. The
receiver is also capable of automatic gain calibration in order to improve precision on RSSI measurements.
3.4.1. Block Diagram
Rx Calibration
Reference
©/
⊗
LNA
CORDIC
Mixers Modulators
DC
Cancellation
Single to
Differential
Channel
Filter
Complex
Filter
Phase
Output
FSK
Demodulator
RFIO
Module
Output
OOK
Demodulator
From
PA1
RSSI
Bypassed
in FSK
Local
Oscillator
AFC
AGC
Figure 7. Receiver Block Diagram
The following sections give a brief description of each of the receiver blocks.
3.4.2. LNA - Single to Differential Buffer
The LNA uses a common-gate topology, which allows for a flat characteristic over the whole frequency range. It is
designed to have an input impedance of 50 Ohms or 200 Ohms (as selected with bit LnaZin in RegLna), and the parasitic
capacitance at the LNA input port is cancelled with the external RF choke. A single to differential buffer is implemented to
improve the second order linearity of the receiver.
The LNA gain, including the single-to-differential buffer, is programmable over a 48 dB dynamic range, and control is either
manual or automatic with the embedded AGC function.
Note In the specific case where the LNA gain is manually set by the user, the receiver will not be able to properly handle
FSK signals with a modulation index smaller than 2 at an input power greater than the 1dB compression point,
tabulated in section 3.4.3.
Table 12 LNA Gain Settings
LnaGainSelect
LNA Gain
Any of the below, set by the AGC loop
Max gain
Gain Setting
000
001
010
011
100
101
110
111
-
G1
G2
G3
G4
G5
G6
-
Max gain - 6 dB
Max gain - 12 dB
Max gain - 24 dB
Max gain - 36 dB
Max gain - 48 dB
Reserved
Page 23
Tel: +86-755-82973805 Fax: +86-755-82973550 E-mail: sales@hoperf.com http://www.hoperf.com
RFM69HW
3.4.3. Automatic Gain Control
By default (LnaGainSelect = 000), the LNA gain is controlled by a digital AGC loop in order to obtain the optimal sensitivity/
linearity trade-off.
Regardless of the data transfer mode (Packet or Continuous), the following series of events takes place when the receiver
is enabled:
The receiver stays in WAIT mode, until RssiValue exceeds RssiThreshold for two consecutive samples. Its power
consumption is the receiver power consumption.
When this condition is satisfied, the receiver automatically selects the most suitable LNA gain, optimizing the
linearity trade-off.
sensitivity/
The programmed LNA gain, read-accessible with LnaCurrentGain in RegLna, is carried on for the whole duration of the
packet, until one of the following conditions is fulfilled:
Packet mode: if AutoRxRestartOn = 0, the LNA gain will remain the same for the reception of the following packet. If
AutoRxRestartOn = 1, after the controller has emptied the FIFO the receiver will re-enter the WAIT mode described
above, after a delay of InterPacketRxDelay, allowing for the distant transmitter to ramp down, hence avoiding a false
RSSI detection. In both cases (AutoRxRestartOn=0 or AutoRxRestartOn=1), the receiver can also re-enter the WAIT
mode by setting RestartRx bit to 1. The user can decide to do so, to manually launch a new AGC procedure.
Continuous mode: upon reception of valid data, the user can decide to either leave the receiver enabled with the
LNA gain, or to restart the procedure, by setting RestartRx bit to 1, resuming the WAIT mode of the receiver,
same
described above.
Notes - the AGC procedure must be performed while receiving preamble in FSK mode
- in OOK mode, the AGC will give better results if performed while receiving a constant “1” sequence
The following figure illustrates the AGC behavior:
Towards
-125 dB
m
16dB
7dB
11dB
9dB
11dB
Pin [dBm]
G1
G2
G3
G4
G5
G6
Higher Sensitivity
Lower Linearity
Lower Sensitivity
Higher Linearity
Lower Noise Figure
Higher Noise Figure
Figure 8. AGC Thresholds Settings
The following table summarizes the performance (typical figures) of the complete receiver:
Page 24
Tel: +86-755-82973805 Fax: +86-755-82973550 E-mail: sales@hoperf.com http://www.hoperf.com
RFM69HW
Table 13 Receiver Performance Summary
Input Power
Pin
Gain
Setting
Receiver Performance (typ)
P-1dB
[dBm]
-37
NF
IIP3
IIP2
[dBm]
[dB]
[dBm]
Pin < AgcThresh1
AgcThresh1 < Pin < AgcThresh2
AgcThresh2 < Pin < AgcThresh3
AgcThresh3 < Pin < AgcThresh4
AgcThresh4 < Pin < AgcThresh5
AgcThresh5 < Pin
G1
G2
G3
G4
G5
G6
7
-18
-15
-8
+35
+40
+48
+62
+68
+75
-31
13
18
27
36
44
-26
-14
-1
>-6
+13
+20
>0
3.4.3.1. RssiThreshold Setting
For correct operation of the AGC, RssiThreshold in RegRssiThresh must be set to the sensitivity of the receiver. The
receiver will remain in WAIT mode until RssiThreshold is exceeded.
Note When AFC is enabled and performed automatically at the receiver startup, the channel filter used by the receiver
during the AFC and the AGC is RxBwAfc instead of the standard RxBw setting. This may impact the sensitivity of
the receiver, and the setting of RssiThreshold accordingly
3.4.3.2. AGC Reference
The AGC reference level is automatically computed in the RFM69HW, according
to:
AGC Reference [dBm] = -174 + NF + DemodSnr +10.log(2*RxBw) + FadingMargin [dBm]
With:
NF = 7dB
: LNA’s Noise Figure at maximum gain
: SNR needed by the demodulator
DemodSnr = 8 dB
RxBw
: Single sideband channel filter bandwidth
FadingMargin = 5 dB : Fading margin
3.4.4. Continuous-Time DAGC
In addition to the automatic gain control described in section 3.4.3, the RFM69HW is capable of continuously adjusting
its gain in the digital domain, after the analog to digital conversion has occured. This feature, named DAGC, is fully
transparent to the end user. The digital gain adjustment is repeated every 2 bits, and has the following benefits:
Fully transparent to the end user
Improves the fading margin of the receiver during the reception of a packet, even if the gain of the LNA is frozen
Improves the receiver robustness in fast fading signal conditions, by quickly adjusting the receiver gain (every 2 bits)
Works in Continuous, Packet, and unlimited length Packet modes
The DAGC is enabled by setting RegTestDagc to 0x20 for low modulation index systems (i.e. when AfcLowBetaOn=1,
refer to section 3.4.16), and 0x30 for other systems. It is recommended to always enable the DAGC.
Page 25
Tel: +86-755-82973805 Fax: +86-755-82973550 E-mail: sales@hoperf.com http://www.hoperf.com
RFM69HW
3.4.5. Quadrature Mixer - ADCs - Decimators
The mixer is inserted between output of the RF buffer stage and the input of the analog to digital converter (ADC) of the
receiver section. This block is designed to translate the spectrum of the input RF signal to base-band, and offer both high
IIP2 and IIP3 responses.
In the lower bands of operation (290 to 510 MHz), the multi-phase mixing architecture with weighted phases improves the
rejection of the LO harmonics in receiver mode, hence increasing the receiver immunity to out-of-band interferers.
The I and Q digitalization is made by two 5th order continuous-time Sigma-Delta Analog to Digital Converters (ADC). Their
gain is not constant over temperature, but the whole receiver is calibrated before reception, so that this inaccuracy has no
impact on the RSSI precision. The ADC output is one bit per channel. It needs to be decimated and filtered afterwards. This
ADC can also be used for temperature measurement, please refer to section 3.4.17 for more details.
The decimators decrease the sample rate of the incoming signal in order to optimize the area and power consumption of
the following receiver blocks.
3.4.6. Channel Filter
The role of the channel filter is to filter out the noise and interferers outside of the channel. Channel filtering on the
RFM69HW is implemented with a 16-tap Finite Impulse Response (FIR) filter, providing an outstanding Adjacent
Channel Rejection performance, even for narrowband applications.
Note to respect oversampling rules in the decimation chain of the receiver, the Bit Rate cannot be set at a higher value
than 2 times the single-side receiver bandwidth (BitRate < 2 x RxBw)
The single-side channel filter bandwidth RxBw is controlled by the parameters RxBwMant and RxBwExp in RegRxBw:
When FSK modulation is enabled:
FXOSC
-----------------------------------------------------------------
RxBw =
RxBw =
p + 2
RxBwMant ⋅
2 RxBwEx
When OOK modulation is enabled:
FXOSC
-----------------------------------------------------------------
p + 3
RxBwMant ⋅
2 RxBwEx
The following channel filter bandwidths are accessible (oscillator is mandated at 32 MHz):
Table 14 Available RxBw Settings
RxBwMant
RxBwExp
RxBw (kHz)
(binary/value) (decimal)
FSK
OOK
ModulationType=00 ModulationType=01
10b / 24
01b / 20
00b / 16
10b / 24
01b / 20
00b / 16
10b / 24
01b / 20
00b / 16
10b / 24
7
7
7
6
6
6
5
5
5
4
2.6
3.1
1.3
1.6
2.0
2.6
3.1
3.9
5.2
6.3
7.8
10.4
3.9
5.2
6.3
7.8
10.4
12.5
15.6
20.8
Page 26
Tel: +86-755-82973805 Fax: +86-755-82973550 E-mail: sales@hoperf.com http://www.hoperf.com
RFM69HW
01b / 20
00b / 16
10b / 24
01b / 20
00b / 16
10b / 24
01b / 20
00b / 16
10b / 24
01b / 20
00b / 16
10b / 24
01b / 20
00b / 16
4
4
3
3
3
2
2
2
1
1
1
0
0
0
25.0
31.3
12.5
15.6
41.7
20.8
50.0
25.0
62.5
31.3
83.3
41.7
100.0
125.0
166.7
200.0
250.0
333.3
400.0
500.0
50.0
62.5
83.3
100.0
125.0
166.7
200.0
250.0
3.4.7. DC Cancellation
DC cancellation is required in zero-IF architecture transceivers to remove any DC offset generated through self-reception.
It is built-in the RFM69HW and its adjustable cutoff frequency fc is controlled in RegRxBw:
Table 15 Available DCC Cutoff Frequencies
DccFreq
fc in
in RegRxBw
% of RxBw
000
001
16
8
010 (default)
011
4
2
100
1
101
0.5
0.25
0.125
110
111
The default value of DccFreq cutoff frequency is typically 4% of the RxBw (channel filter BW). The cutoff frequency of the
DCC can however be increased to slightly improve the sensitivity, under wider modulation conditions. It is advised to adjust
the DCC setting while monitoring the receiver sensitivity.
3.4.8. Complex Filter - OOK
In OOK mode the RFM69HW is modified to a low-IF architecture. The IF frequency is automatically set to half the single
side bandwidth of the channel filter (FIF = 0.5 x RxBw). The Local Oscillator is automatically offset by the IF in the OOK
receiver. A complex filter is implemented on the module to attenuate the resulting image frequency by typically 30 dB.
Note this filter is automatically bypassed when receiving FSK signals (ModulationType = 00 in RegDataModul).
3.4.9. RSSI
The RSSI block evaluates the amount of energy available within the receiver channel bandwidth. Its resolution is 0.5 dB,
and it has a wide dynamic range to accommodate both small and large signal levels that may be present. Its acquisition
time is very short, taking only 2 bit periods. The RSSI sampling must occur during the reception of preamble in FSK, and
constant “1” reception in OOK.
Page 27
Tel: +86-755-82973805 Fax: +86-755-82973550 E-mail: sales@hoperf.com http://www.hoperf.com
RFM69HW
Note - RssiValue can only be read when it exceeds RssiThreshold
- The receiver is capable of automatic gain calibration, in order to improve the precision of its RSSI measurements.
This function injects a known RF signal at the LNA input, and calibrates the receiver gain accordingly. This
calibration is automatically performed during the PLL start-up, making it a transparent process to the end-user
- RSSI accuracy depends on all components located between the antenna port and pin RFIO, and is therefore
limited to a few dB. Board-level calibration is advised to further improve accuracy
RSSI Chart - With AGC
0.0
-20.0
-40.0
-60.0
-80.0
-100.0
-120.0
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
0
Pin [dBm]
Figure 9. RSSI Dynamic Curve
3.4.10. Cordic
The Cordic task is to extract the phase and the amplitude of the modulation vector (I+j.Q). This information, still in the
digital domain is used:
Phase output: used by the FSK demodulator and the AFC blocks.
Amplitude output: used by the RSSI block, for FSK demodulation, AGC and automatic gain calibration purposes.
Q(t)
Real-
time
Magnitude
Real-time Phase
I(t)
Figure 10. Cordic Extraction
Page 28
Tel: +86-755-82973805 Fax: +86-755-82973550 E-mail: sales@hoperf.com http://www.hoperf.com
RFM69HW
3.4.11. FSK Demodulator
The FSK demodulator of the RFM69HW is designed to demodulate FSK, GFSK, MSK and GMSK modulated signals. It
is most efficient when the modulation index of the signal is greater than 0.5 and below 10:
The output of the FSK demodulator can be fed to the Bit Synchronizer (described in section 3.4.13), to provide the
companion processor with a synchronous data stream in Continuous mode.
3.4.12. OOK Demodulator
The OOK demodulator performs a comparison of the RSSI output and a threshold value. Three different threshold modes
are available, configured through bits OokThreshType in RegOokPeak.
The recommended mode of operation is the "Peak" threshold mode, illustrated in Figure 11:
RSSI
[dBm]
‘’Peak -6dB’’ Threshold
‘’Floor’’ threshold defined by
OokFixedThresh
Noise floor of
receiver
Time
Zoom
Decay in dB as defined in
OokPeakThreshStep
Fixed 6dB difference
Period as defined in
OokPeakThreshDec
Figure 11. OOK Peak Demodulator Description
In peak threshold mode the comparison threshold level is the peak value of the RSSI, reduced by 6dB. In the absence of
an input signal, or during the reception of a logical "0", the acquired peak value is decremented by one
OokPeakThreshStep every OokPeakThreshDec period.
When the RSSI output is null for a long time (for instance after a long string of "0" received, or if no transmitter is present),
the peak threshold level will continue falling until it reaches the "Floor Threshold", programmed in OokFixedThresh.
The default settings of the OOK demodulator lead to the performance stated in the electrical specification. However, in
applications in which sudden signal drops are awaited during a reception, the three parameters should be optimized
accordingly.
Page 29
Tel: +86-755-82973805 Fax: +86-755-82973550 E-mail: sales@hoperf.com http://www.hoperf.com
RFM69HW
3.4.12.1. Optimizing the Floor Threshold
OokFixedThresh determines the sensitivity of the OOK receiver, as it sets the comparison threshold for weak input signals
(i.e. those close to the noise floor). Significant sensitivity improvements can be generated if configured correctly.
Note that the noise floor of the receiver at the demodulator input depends on:
The noise figure of the receiver.
The gain of the receive chain from antenna to base band.
The matching - including SAW filter if any.
The bandwidth of the channel filters.
It is therefore important to note that the setting of OokFixedThresh will be application dependant. The following procedure
is recommended to optimize OokFixedThresh.
Set RFM69HW in OOK Rx mode
Adjust Bit Rate, Channel filter BW
Default OokFixedThresh setting
No input signal
Continuous Mode
Monitor DIO2/DATA pin
Increment
OokFixedThresh
Glitch activity
on DATA
?
Optimization complete
Figure 12. Floor Threshold Optimization
The new floor threshold value found during this test should be used for OOK reception with those receiver settings.
3.4.12.2. Optimizing OOK Demodulator for Fast Fading Signals
A sudden drop in signal strength can cause the bit error rate to increase. For applications where the expected signal drop
can be estimated, the following OOK demodulator parameters OokPeakThreshStep and OokPeakThreshDec can be
optimized as described below for a given number of threshold decrements per bit. Refer to RegOokPeak to access those
settings.
3.4.12.3. Alternative OOK Demodulator Threshold Modes
In addition to the Peak OOK threshold mode, the user can alternatively select two other types of threshold detectors:
Fixed Threshold: The value is selected through OokFixedThresh
Average Threshold: Data supplied by the RSSI block is averaged, and this operation mode should only be used
DC-free encoded data.
with
Page 30
Tel: +86-755-82973805 Fax: +86-755-82973550 E-mail: sales@hoperf.com http://www.hoperf.com
RFM69HW
3.4.13. Bit Synchronizer
The Bit Synchronizer is a block that provides a clean and synchronized digital output, free of glitches. Its output is made
available on pin DIO1/DCLK in Continuous mode and can be disabled through register settings. However, for optimum
receiver performance its use when running Continuous mode is strongly advised.
The Bit Synchronizer is automatically activated in Packet mode. Its bit rate is controlled by BitRateMsb and BitRateLsb in
RegBitrate.
Raw demodulator
output
(FSK or OOK)
DATA
BitSync Output To
pin DATA and
DCLK in continuous
mode
DCLK
Figure 13. Bit Synchronizer Description
To ensure correct operation of the Bit Synchronizer, the following conditions have to be satisfied:
A preamble (0x55 or 0xAA) of 12 bits is required for synchronization (from the RxReady interrupt)
The subsequent payload bit stream must have at least one transition form '0' to '1' or '1' to '0 every 16 bits during data
transmission
The bit rate matching between the transmitter and the receiver must be better than 6.5 %.
Notes - If the Bit Rates of transmitter and receiver are known to be the same, the RFM69HW will be able to receive
an infinite unbalanced sequence (all “0s” or all ”1s”) with no restriction.
- If there is a difference in Bit Rate between Tx and Rx, the amount of adjacent bits at the same level that the
BitSync can withstand can be estimated as follows:
- This implies approximately 6 consecutive unbalanced bytes when the Bit Rate precision is 1%, which is easily
achievable (crystal tolerance is in the range of 50 to 100 ppm).
3.4.14. Frequency Error Indicator
This function provides information about the frequency error of the local oscillator (LO) compared with the carrier frequency
of a modulated signal at the input of the receiver. When the FEI block is launched, the frequency error is measured and the
Page 31
Tel: +86-755-82973805 Fax: +86-755-82973550 E-mail: sales@hoperf.com http://www.hoperf.com
RFM69HW
signed result is loaded in FeiValue in RegFei, in 2’s complement format. The time required for an FEI evaluation is 4 times
the bit period.
To ensure a proper behavior of the FEI:
The operation must be done during the reception of preamble
The sum of the frequency offset and the 20 dB signal bandwidth must be lower than the base band filter bandwidth
The 20 dB bandwidth of the signal can be evaluated as follows (double-side bandwidth):
⋅
The frequency error, in Hz, can be calculated with the following formula:
SRXF1M23699HW in Rx
mode
Preamble-modulated input signal
Signal level > Sensitivity
Set FeiStart
= 1
No
FeiDone
= 1
Yes
Read
FeiValue
Figure 14. FEI Process
3.4.15. Automatic Frequency Correction
The AFC is based on the FEI block, and therefore the same input signal and receiver setting conditions apply. When the
AFC procedure is done, AfcValue is directly subtracted to the register that defines the frequency of operation of the
module, FRF. The AFC can be launched:
Each time the receiver is enabled, if AfcAutoOn = 1
Upon user request, by setting bit AfcStart in RegAfcFei, if AfcAutoOn = 0
Page 32
Tel: +86-755-82973805 Fax: +86-755-82973550 E-mail: sales@hoperf.com http://www.hoperf.com
RFM69HW
When the AFC is automatically triggered (AfcAutoOn = 1), the user has the option to:
Clear the former AFC correction value, if AfcAutoClearOn = 1
Start the AFC evaluation from the previously corrected frequency. This may be useful in systems in which the LO keeps
on drifting in the “same direction”. Ageing compensation is a good example.
The RFM69HW offers an alternate receiver bandwidth setting during the AFC phase, to accommodate large LO drifts. If
the user considers that the received signal may be out of the receiver bandwidth, a higher channel filter bandwidth can
be programmed in RegAfcBw, at the expense of the receiver noise floor, which will impact upon sensitivity.
3.4.16. Optimized Setup for Low Modulation Index Systems
For wide band systems, where AFC is usually not required (XTAL inaccuracies do not typically impact the sensitivity), it
is recommended to offset the LO frequency of the receiver to avoid desensitization. This can be simply done by
modifying Frf in RegFrfLsb. A good rule of thumb is to offset the receiver’s LO by 10% of the expected transmitter
frequency deviation.
For narrow band systems, it is recommended to perform AFC. The RFM69HW has a dedicated AFC, enabled
when
AfcLowBetaOn in RegAfcCtrl is set to 1. A frequency offset, programmable through LowBetaAfcOffset in RegTestAfc, is
added and is calculated as follows:
Offset = LowBetaAfcOffset x 488 Hz
The user should ensure that the programmed offset exceeds the DC canceller’s cutoff frequency, set through DccFreqAfc
in RegAfcBw.
RX
TX
RX & TX
FeiValue
AfcValue
Standard AFC
AfcLowBetaOn = 0
f
f
f
RX
TX
TX RX
FeiValue
AfcValue
LowBetaAfcOffset
Optimized AFC
AfcLowBetaOn =
1
f
Before AFC
After AFC
Figure 15. Optimized AFC (AfcLowBetaOn=1)
As shown on Figure 15, a standard AFC sequence uses the result of the FEI to correct the LO frequency and align both
local oscillators. When the optimized AFC is enabled (AfcLowBetaOn=1), the receiver’s LO is corrected by “FeiValue +
LowBetaAfcOffset”.
When the optimized AFC routine is enabled, the receiver startup time can be computed as follows (refer to section 4.2.3):
TS_RE_AGC&AFC (optimized AFC) = Tana + 4.Tcf + 4.Tdcc + 3.Trssi + 2.Tafc + 2.Tpllafc
Page 33
Tel: +86-755-82973805 Fax: +86-755-82973550 E-mail: sales@hoperf.com http://www.hoperf.com
RFM69HW
3.4.17. Temperature Sensor
When temperature is measured, the receiver ADC is used to digitize the sensor response. Most receiver blocks are
disabled, and temperature measurement can only be triggered in Standby or Frequency Synthesizer modes.
The response of the temperature sensor is -1°C / Lsb. A CMOS temperature sensor is not accurate by nature, therefore it
should be calibrated at ambient temperature for precise temperature readings.
TempValue
-1°C/Lsb
TempValue(t)
TempValue(t)-1
Returns 150d (typ.)
Needs calibration
t t+1
Ambient
-40°C
+85°C
Figure 16. Temperature Sensor Response
It takes less than 100 microseconds for the RFM69HW to evaluate the temperature (from setting TempMeasStart to 1 to
TempMeasRunning reset).
3.4.18. Timeout Function
The RFM69HW includes a Timeout function, which allows it to automatically shut-down the receiver after a
receive sequence and therefore save energy.
Timeout interrupt is generated TimeoutRxStart x 16x Tbit after switching to RX mode if RssiThreshold flag does not
raise within this time frame
Timeout interrupt is generated TimeoutRssiThresh x 16 x Tbit after RssiThreshold flag has been raised.
This timeout interrupt can be used to warn the companion processor to shut down the receiver and return to a lower power
mode.
Page 34
Tel: +86-755-82973805 Fax: +86-755-82973550 E-mail: sales@hoperf.com http://www.hoperf.com
RFM69HW
4. Operating Modes
4.1. Basic Modes
The circuit can be set in 5 different basic modes which are described in Table 16.
By default, when switching from a mode to another one, the sub-blocks are woken up according to a pre-defined and
optimized sequence. Alternatively, these operating modes can be selected directly by disabling the automatic sequencer
(SequencerOff in RegOpMode = 1).
Table 16 Basic Transceiver Modes
ListenOn
Mode
Selected mode
Enabled blocks
in RegOpMode
in RegOpMode
0
0
0
0
0
1
0 0 0
0 0 1
0 1 0
0 1 1
1 0 0
x
Sleep Mode
Stand-by Mode
FS Mode
None
Top regulator and crystal oscillator
Frequency synthesizer
Transmit Mode
Receive Mode
Listen Mode
Frequency synthesizer and transmitter
Frequency synthesizer and receiver
See Listen Mode, section 4.3
4.2. Automatic Sequencer and Wake-Up Times
By default, when switching from one operating mode to another, the circuit takes care of the sequence of events in such a
way that the transition timing is optimized. For example, when switching from Sleep mode to Transmit mode, the
RFM69HW goes first to Standby mode (XO started), then to frequency synthesizer mode, and finally, when the PLL has
locked, to transmit mode. Entering transmit mode is also made according to a predefined sequence starting with the
wake-up of the PA regulator before applying a ramp-up on the PA and generating the DCLK clock.
The crystal oscillator wake-up time, TS_OSC, is directly related to the time for the crystal oscillator to reach its steady
state. It depends notably on the crystal characteristics.
The frequency synthesizer wake-up time, TS_FS, is directly related to the time needed by the PLL to reach its steady
state. The signal PLL_LOCK, provided on an external pin, gives an indication of the lock status. It goes high when the
PLL reaches its locking range.
Four specific cases can be highlighted:
Transmitter Wake Up time from Sleep mode
= TS_OSC + TS_FS + TS_TR
Receiver Wake Up time from Sleep mode
= TS_OSC + TS_FS + TS_RE
Receiver Wake Up time from Sleep mode, AGC enabled
Receiver Wake Up time from Sleep mode, AGC and AFC enabled
= TS_OSC + TS_FS + TS_RE_AGC
= TS_OSC + TS_FS + TS_RE_AGC&AFC
These timings are detailed in sections 4.2.1 and 4.2.3.
In applications where the target average power consumption, or the target startup time, do not require setting the
RFM69HW in the lowest power modes (Sleep or Standby), the respective timings TS_OSC and TS_FS in the former
equations can be omitted.
Page 35
Tel: +86-755-82973805 Fax: +86-755-82973550 E-mail: sales@hoperf.com http://www.hoperf.com
RFM69HW
4.2.1. Transmitter Startup Time
The transmitter wake-up time, TS_TR, is given by the sequence controlled by the digital part. It is a pure digital delay which
depends on the bit rate and the ramp-up time. In FSK mode, this time can be derived from the following equation.
where PaRamp is the ramp-up time programmed in RegPaRamp and Tbit is the bit time.
In OOK mode, this equation can be simplified to the following:
Tx startup request
(sequencer or user)
TS_TR
1.25 x PaRamp
Analog
group delay
XO Started and PLL is locked
0.5 x Tbit
(only in FSK
mode)
Transmission of Packet
5
us
ModeReady
TxReady
Figure 17. Tx Startup, FSK and OOK
4.2.2. Tx Start Procedure
As described in the former section, ModeReady and TxReady interrupts warn the uC that the transmitter is ready to
transmit data
In Continuous mode, the preamble bits preceding the payload can be applied on the DIO2/DATA pin immediately after
any of these interrupts have fired. The DCLK signal, activated on pin DIO1/DCLK can also be used to start toggling the
DATA pin, as described on Figure 30.
In Packet mode, the RFM69HW will automatically modulate the RF signal with preamble bytes as soon as TxReady
or
ModeReady happen. The actual packet transmission (starting with the number of preambles specified in PreambleSize)
will start when the TxStartCondition is fulfilled.
4.2.3. Receiver Startup Time
It is highly recommended to use the built-in sequencer of the RFM69HW, to optimize the delays when setting the
module in receive mode. It guarantees the shortest startup times, hence the lowest possible energy usage, for battery
operated systems.
The startup times of the receiver can be calculated from the following:
Page 36
Tel: +86-755-82973805 Fax: +86-755-82973550 E-mail: sales@hoperf.com http://www.hoperf.com
RFM69HW
Rx startup request
(sequencer or user)
TS_RE
Analog FE’s
group delay
Channel Filter’s
group delay
DC Cutoff’s
group delay sampling sampling
RSSI
RSSI
XO Started and PLL is locked
Reception of Packet
Tana
Tcf
Tdcc
Trssi
Trssi
ModeReady
RxReady
Received Packet Preamble may start
Figure 18. Rx Startup - No AGC, no AFC
The LNA gain is adjusted by
the AGC, according to the
RSSI result
Rx startup request
(sequencer or user)
TS_RE_AGC
Analog FE’s
group delay
Channel Filter’s
group delay
DC Cutoff’s
group delay sampling sampling
RSSI
RSSI
Channel Filter’s
group delay
DC Cutoff’s
group delay sampling
RSSI
XO Started and PLL is locked
Reception of Packet
Tana
Tcf
Tdcc
Trssi
Trssi
Tcf
Tdcc
Trssi
ModeReady
RxReady
Received Packet Preamble may start
Figure 19. Rx Startup - AGC, no AFC
The LNA gain is adjusted by
the AGC, according to the
RSSI result
Rx startup request
(sequencer or user)
Carrier Frequency is adjusted
by the AFC
TS_RE_AGC&AFC
XO Started and Analog FE’s Channel Filter’s DC Cutoff’s
RSSI
RSSI
Channel Filter’s DC Cutoff’s
RSSI
PLL
lock
Channel Filter’s DC Cutoff’s
AFC
Reception of Packet
PLL is locked
group delay
group delay
group delay sampling sampling
group delay
group delay sampling
group delay
group delay
Tana
Tcf
Tdcc
Trssi
Trssi
Tcf
Tdcc Trssi
Tafc Tpllafc
Tcf
Tdcc
ModeReady
RxReady
Received Packet Preamble may start
Figure 20. Rx Startup - AGC and AFC
The different timings shown above are as follows:
Group delay of the analog front end:
Channel filter’s group delay in FSK mode:
Channel filter’s group delay in OOK mode:
DC Cutoff’s group delay:
Tana = 20 us
Tcf = 21 / (4.RxBw)
Tcf = 34 / (4.RxBw)
Tdcc = max(8 , 2^(round(log2(8.RxBw.Tbit)+1)) / (4.RxBw)
Tpllafc = 5 / PLLBW (PLLBW = 300 kHz)
PLL lock time after AFC adjustment:
AFC sample time:
Tafc = 4 x Tbit
(also denoted TS_AFC in the general specification)
RSSI sample time:
Trssi = 2 x int(4.RxBw.Tbit)/(4.RxBw)
(aka TS_RSSI)
Note The above timings represent maximum settling times, and shorter settling times may be observed in real cases
Page 37
Tel: +86-755-82973805 Fax: +86-755-82973550 E-mail: sales@hoperf.com http://www.hoperf.com
RFM69HW
4.2.4. Rx Start Procedure
As described in the former sections, the RxReady interrupt warns the uC that the receiver is ready.
In Continuous mode with Bit Synchronizer, the receiver will start locking its Bit Synchronizer on a minimum or 12 bits of
received preamble (see section 3.4.13 for details), before the reception of correct Data, or Sync Word (if enabled) can
occur.
In Continuous mode without Bit Synchronizer, valid data will be available on DIO2/DATA right after the RxReady
interrupt.
In Packet mode, the receiver will start locking its Bit Synchronizer on a minimum or 12 bits of received preamble (see
section 3.4.13 for details), before the reception of correct Data, or Sync Word (if enabled) can occur.
4.2.5. Optimized Frequency Hopping Sequences
In a frequency hopping-like application, it is required to turn off the transmitter when hopping from one channel to another,
to avoid spectral splatter and obtain the best spectral purity.
Transmitter hop from Ch A to Ch B: it is advised to step through the Rx mode:
(0) RFM69HW is in Tx mode in Ch A
(1) Program the RFM69HW in Rx mode
(2) Change the carrier frequency in the RegFrf registers
(3) Turn the transceiver back to Tx mode
(4) Respect the Tx start procedure, described in section 4.2.2
Receiver hop from Ch A to Ch B:
(0) RFM69HW is in Rx mode in
Ch A
(1) Change the carrier frequency in the RegFrf registers
(2) Program the RFM69HW in FS mode
(3) Turn the transceiver back to Rx mode
(4) Respect the Rx start procedure, described in section 4.2.4
Note all sequences described above are assuming that the sequencer is turned on (SequencerOff=0 in RegOpMode).
Page 38
Tel: +86-755-82973805 Fax: +86-755-82973550 E-mail: sales@hoperf.com http://www.hoperf.com
RFM69HW
4.3. Listen Mode
The circuit can be set to Listen mode, by setting ListenOn in RegOpMode to 1 while in Standby mode. In this mode,
RFM69HW spends most of the time in Idle mode, during which only the RC oscillator runs. Periodically the receiver is
woken up and listens for an RF signal. If a wanted signal is detected, the receiver is kept on and the data is demodulated.
Otherwise, if a wanted signal hasn't been detected after a pre-defined period of time, the receiver is disabled until the next
time period.
This periodical Rx wake-up requirement is very common in low power applications. On RFM69HW it is handled locally by
the
Listen mode block without using uC resources or energy.
The simplified timing diagram of this procedure is illustrated in Figure 21.
tListenIdle
Rx
Idle
Rx
time
tListenRx
tListenRx
Figure 21. Listen Mode Sequence (no wanted signal is received)
4.3.1. Timings
The duration of the Idle phase is given by tListenIdle. The time during which the receiver is on and waits for a signal is given
by tListenRx. tListenRx includes the wake-up time of the receiver, described in section 4.2.3. This duration can be
programmed in the configuration registers via the serial interface.
Both time periods tListenRx and tListenIdle (denoted tListenX in the following text) are fixed by two parameters from the
configuration register and are calculated as follows:
= ListenCoefX ∗Listen ResolX
tListenX
where ListenResolX is the Rx or Idle resolution and is independently programmable on three values (64us, 4.1ms or
262ms), whereas ListenCoefX is an integer between 1 and 255. All parameters are located in RegListen registers.
The timing ranges are tabulated in Table 17 below.
Table 17 Range of Durations in Listen Mode
ListenResolX
Min duration
Max duration
( ListenCoef = 1 )
( ListenCoef = 255 )
01
10
11
64 us
4.1 ms
16 ms
1.04
67
s
0.26
s
s
Page 39
Tel: +86-755-82973805 Fax: +86-755-82973550 E-mail: sales@hoperf.com http://www.hoperf.com
RFM69HW
ADVANCED COMMUNICATIONS & SENSING
DATASHEET
Notes - the accuracy of the typical timings given in Table 17 will depend in the RC oscillator calibration
- RC oscillator calibration is required, and must be performed at power up. See section 4.3.5 for details
4.3.2. Criteria
The criteria taken for detecting a wanted signal and hence deciding to maintain the receiver on is defined by ListenCriteria
in RegListen1.
Table 18 Signal Acceptance Criteria in Listen Mode
ListenCriteria
Input Signal Power
SyncAddressMatch
>= RssiThreshold
0
1
Required
Required
Not Required
Required
4.3.3. End of Cycle Actions
The action taken after detection of a packet, is defined by ListenEnd in RegListen3, as described in the table below.
Table 19 End of Listen Cycle Actions
ListenEnd
Description
Module stays in Rx mode. Listen mode stops and must be disabled.
00
01
Module stays in Rx mode until PayloadReady or Timeout interrupt occurs. It then goes to the
mode defined by Mode. Listen mode stops and must be disabled.
Module stays in Rx mode until PayloadReady or Timeout interrupt occurs. Listen mode then
10
resumes in Idle state. FIFO content is lost at next Rx wakeup.
Page 40
Tel: +86-755-82973805 Fax: +86-755-82973550 E-mail: sales@hoperf.com http://www.hoperf.com
RFM69HW
ADVANCED COMMUNICATIONS & SENSING
DATASHEET
Upon detection of a valid packet, the sequencing is altered, as shown below:
PayloadReady
ListenCriteria
passed
Idle
Idle
Idle
Rx
Rx
Rx
ListenEnd = 00
ListenEnd = 01
ListenEnd = 10
Listen Mode
Listen Mode
Listen Mode
Mode
Idle
Rx
Figure 22. Listen Mode Sequence (wanted signal is received)
4.3.4. Stopping Listen Mode
To abort Listen mode operation, the following procedure must be respected:
Program RegOpMode with ListenOn=0, ListenAbort=1, and the desired setting for the Mode bits (Sleep, Stdby, FS, Rx
or Tx mode) in a single SPI access
Program RegOpMode with ListenOn=0, ListenAbort=0, and the desired setting for the Mode bits (Sleep, Stdby, FS, Rx
or Tx mode) in a second SPI access
4.3.5. RC Timer Accuracy
All timings of the Listen Mode rely on the accuracy of the internal low-power RC oscillator. This oscillator is automatically
calibrated at the device power-up, and it is a user-transparent process.
For applications enduring large temperature variations, and for which the power supply is never removed, RC calibration
can be performed upon user request. RcCalStart in RegOsc1 can be used to trigger this calibration, and the flag
RcCalDone will be set automatically when the calibration is over.
Page 41
Tel: +86-755-82973805 Fax: +86-755-82973550 E-mail: sales@hoperf.com http://www.hoperf.com
RFM69HW
ADVANCED COMMUNICATIONS & SENSING
4.4. AutoModes
DATASHEET
Automatic modes of packet handler can be enabled by configuring the related parameters in RegAutoModes.
The intermediate mode of the module is called IntermediateMode and the enter and exit conditions to/from this
intermediate mode can be configured through the parameters EnterCondition & ExitCondition.
The enter and exit conditions cannot be used independently of each other i.e. both should be enabled at the same time.
The initial and the final state is the one configured in Mode in RegOpMode. The initial & final states can be different by
configuring the modes register while the module is in intermediate mode. The pictorial description of the auto modes is
shown
below.
Intermediate State
defined by IntermediateMode
ExitCondition
EnterCondition
Initial state defined
Final state defined
By Mode in RegOpMode
By Mode in RegOpMode
Figure 23. Auto Modes of Packet Handler
Some typical examples of AutoModes usage are described below:
Automatic transmission (AutoTx) : Mode = Sleep, IntermediateMode = Tx, EnterCondition = FifoLevel, ExitCondition =
PacketSent
Automatic reception (AutoRx) : Mode = Rx, IntermediateMode = Sleep, EnterCondition = CrcOk, ExitCondition = falling
edge of FifoNotEmpty
Automatic reception of acknowledge (AutoRxAck): Mode = Tx, IntermediateMode = Rx, EnterCondition = PacketSent,
ExitCondition = CrcOk
...
Page 42
Tel: +86-755-82973805 Fax: +86-755-82973550 E-mail: sales@hoperf.com http://www.hoperf.com
RFM69HW
5. Data Processing
5.1. Overview
5.1.1. Block Diagram
Figure below illustrates the RFM69HW data processing circuit. Its role is to interface the data to/from the modulator/
demodulator and the uC access points (SPI and DIO pins). It also controls all the configuration registers.
The circuit contains several control blocks which are described in the following paragraphs.
DIO0
Tx/Rx
DIO1
DIO2
DIO3
DIO4
DIO5
CONTROL
Rx
Tx
Data
SYNC
RECOG.
PACKET
HANDLER
FIFO
(+SR)
SPI
NSS
SCK
MOSI
MISO
Potential datapaths (data operation mode dependant)
Figure 24. RFM69HW Data Processing Conceptual
View
The RFM69HW implements several data operation modes, each with their own data path through the data
processing section. Depending on the data operation mode selected, some control blocks are active whilst others remain
disabled.
5.1.2. Data Operation Modes
The RFM69HW has two different data operation modes selectable by the user:
Continuous mode: each bit transmitted or received is accessed in real time at the DIO2/DATA pin. This mode may be
used if adequate external signal processing is available.
Packet mode (recommended):user only provides/retrieves payload bytes to/from the FIFO. The packet is automatically
built with preamble, Sync word, and optional AES, CRC, and DC-free encoding schemes The reverse operation is
performed in reception. The uC processing overhead is hence significantly reduced compared to Continuous mode.
Depending on the optional features activated (CRC, AES, etc) the maximum payload length is limited to FIFO size, 255
bytes or unlimited.
Each of these data operation modes is described fully in the following sections.
Page 43
Tel: +86-755-82973805 Fax: +86-755-82973550 E-mail: sales@hoperf.com http://www.hoperf.com
RFM69HW
5.2. Control Block Description
5.2.1. SPI Interface
The SPI interface gives access to the configuration register via a synchronous full-duplex protocol corresponding to CPOL
= 0 and CPHA = 0 in Motorola/Freescale nomenclature. Only the slave side is implemented.
Three access modes to the registers are provided:
SINGLE access: an address byte followed by a data byte is sent for a write access whereas an address byte is sent and
a read byte is received for the read access. The NSS pin goes low at the begin of the frame and goes high after the data
byte.
BURST access: the address byte is followed by several data bytes. The address is automatically incremented internally
between each data byte. This mode is available for both read and write accesses. The NSS pin goes low at the
beginning of the frame and stay low between each byte. It goes high only after the last byte transfer.
FIFO access: if the address byte corresponds to the address of the FIFO, then succeeding data byte will address the
FIFO. The address is not automatically incremented but is memorized and does not need to be sent between each data
byte. The NSS pin goes low at the beginning of the frame and stay low between each byte. It goes high only after the
last byte transfer.
Figure below shows a typical SPI single access to a register.
Figure 25. SPI Timing Diagram (single access)
MOSI is generated by the master on the falling edge of SCK and is sampled by the slave (i.e. this SPI interface) on the
rising edge of SCK. MISO is generated by the slave on the falling edge of SCK.
A transfer always starts by the NSS pin going low. MISO is high impedance when NSS is high.
The first byte is the address byte. It is made of:
wnr bit, which is 1 for write access and 0 for read access
7 bits of address, MSB first
The second byte is a data byte, either sent on MOSI by the master in case of a write access, or received by the master on
MISO in case of read access. The data byte is transmitted MSB first.
Proceeding bytes may be sent on MOSI (for write access) or received on MISO (for read access) without rising NSS and
re-sending the address. In FIFO mode, if the address was the FIFO address then the bytes will be written / read at the
FIFO address. In Burst mode, if the address was not the FIFO address, then it is automatically incremented at each new
byte received.
Page 44
Tel: +86-755-82973805 Fax: +86-755-82973550 E-mail: sales@hoperf.com http://www.hoperf.com
RFM69HW
The frame ends when NSS goes high. The next frame must start with an address byte. The SINGLE access mode is
actually a special case of FIFO / BURST mode with only 1 data byte transferred.
During the write access, the byte transferred from the slave to the master on the MISO line is the value of the written
register before the write operation.
5.2.2. FIFO
5.2.2.1. Overview and Shift Register (SR)
In packet mode of operation, both data to be transmitted and that has been received are stored in a configurable FIFO
(First In First Out) device. It is accessed via the SPI interface and provides several interrupts for transfer management.
The FIFO is 1 byte wide hence it only performs byte (parallel) operations, whereas the demodulator functions serially. A
shift register is therefore employed to interface the two devices. In transmit mode it takes bytes from the FIFO and outputs
them serially (MSB first) at the programmed bit rate to the modulator. Similarly, in Rx the shift register gets bit by bit data
from the demodulator and writes them byte by byte to the FIFO. This is illustrated in figure below.
FIFO
byte1
byte0
8
Data Tx/Rx
SR (8bits)
1
MSB
LSB
Figure 26. FIFO and Shift Register (SR)
Note When switching to Sleep mode, the FIFO can only be used once the ModeReady flag is set (quasi immediate from
all modes except from Tx)
5.2.2.2. Size
The FIFO size is fixed to 66 bytes.
5.2.2.3. Interrupt Sources and Flags
FifoNotEmpty: FifoNotEmpty interrupt source is low when byte 0, i.e. whole FIFO, is empty. Otherwise it is high.
Note that when retrieving data from the FIFO, FifoNotEmpty is updated on NSS falling edge, i.e. when FifoNotEmpty
is updated to low state the currently started read operation must be completed. In other words, FifoNotEmpty state
must be checked after each read operation for a decision on the next one (FifoNotEmpty = 1: more byte(s) to read;
FifoNotEmpty = 0: no more byte to read).
FifoFull: FifoFull interrupt source is high when the last FIFO byte, i.e. the whole FIFO, is full. Otherwise it is low.
FifoOverrunFlag: FifoOverrunFlag is set when a new byte is written by the user (in Tx or Standby modes) or the SR
(inRx mode) while the FIFO is already full. Data is lost and the flag should be cleared by writing a 1, note that the
FIFO will also be cleared.
PacketSent: PacketSent interrupt source goes high when the SR's last bit has been sent.
FifoLevel: Threshold can be programmed by FifoThreshold in RegFifoThresh. Its behavior is illustrated in figure
below.
Page 45
Tel: +86-755-82973805 Fax: +86-755-82973550 E-mail: sales@hoperf.com http://www.hoperf.com
RFM69HW
FifoLevel
1
0
B
B+1
# of bytes in FIFO
Figure 27. FifoLevel IRQ Source Behavior
Note - FifoLevel interrupt is updated only after a read or write operation on the FIFO. Thus the interrupt cannot be
dynamically updated by only changing the FifoThreshold parameter
- FifoLevel interrupt is valid as long as FifoFull does not occur. An empty FIFO will restore its normal operation
5.2.2.4. FIFO Clearing
Table below summarizes the status of the FIFO when switching between different modes
Table 20 Status of FIFO when Switching Between Different Modes of the Module
From
Stdby
To
Sleep
Stdby
Tx
FIFO status
Not cleared
Not cleared
Not cleared
Cleared
Comments
Sleep
Stdby/Sleep
Stdby/Sleep
Rx
To allow the user to write the FIFO in Stdby/Sleep before Tx
To allow the user to read FIFO in Stdby/Sleep mode after Rx
Rx
Tx
Cleared
Rx
Stdby/Sleep
Any
Not cleared
Cleared
Tx
5.2.3. Sync Word Recognition
5.2.3.1. Overview
Sync word recognition (also called Pattern recognition) is activated by setting SyncOn in RegSyncConfig. The bit
synchronizer must also be activated in continuous mode (automatically done in Packet mode) .
The block behaves like a shift register; it continuously compares the incoming data with its internally programmed Sync
word and sets SyncAddressMatch when a match is detected. This is illustrated in Figure 28 below.
Page 46
Tel: +86-755-82973805 Fax: +86-755-82973550 E-mail: sales@hoperf.com http://www.hoperf.com
RFM69HW
Rx DATA
(NRZ)
Bit N-x =
Sync_value[x]
Bit N-1 =
Bit N =
Sync_value[1] Sync_value[0]
DCLK
SyncAddressMatch
Figure 28. Sync Word Recognition
During the comparison of the demodulated data, the first bit received is compared with bit 7 (MSB) of RegSyncValue1 and
the last bit received is compared with bit 0 (LSB) of the last byte whose address is determined by the length of the Sync
word.
When the programmed Sync word is detected the user can assume that this incoming packet is for the node and can be
processed accordingly.
SyncAddressMatch is cleared when leaving Rx or FIFO is emptied.
5.2.3.2. Configuration
Size: Sync word size can be set from 1 to 8 bytes (i.e. 8 to 64 bits) via SyncSize in RegSyncConfig. In Packet mode
this field is also used for Sync word generation in Tx mode.
Error tolerance: The number of errors tolerated in the Sync word recognition can be set from 0 to 7 bits to via
SyncTol.
Value: The Sync word value is configured in SyncValue(63:0). In Packet mode this field is also used for Sync word
generation in Tx mode.
Note SyncValue choices containing 0x00 bytes are not allowed
5.2.4. Packet Handler
The packet handler is the block used in Packet mode. Its functionality is fully described in section 5.5.
5.2.5. Control
The control block configures and controls the full module's behavior according to the settings programmed in the
configuration registers.
5.3. Digital IO Pins Mapping
Six general purpose IO pins are available on the RFM69HW, and their configuration in Continuous or Packet mode
is controlled through RegDioMapping1 and RegDioMapping2.
Page 47
Tel: +86-755-82973805 Fax: +86-755-82973550 E-mail: sales@hoperf.com http://www.hoperf.com
RFM69HW
ADVANCED COMMUNICATIONS & SENSING
DATASHEET
5.3.1. DIO Pins Mapping in Continuous Mode
Table 21 DIO Mapping, Continuous Mode
Mode
Diox
Mapping
00
DIO5
DIO4
DIO3
DIO2
DIO1
DIO0
Sleep
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
01
10
11
Au
Au
Au
t
t
t
oMode
-
ModeReady
ModeReady
Stdby
FS
00
01
10
11
ClkOut
-
-
-
-
-
-
-
oMode
-
ModeReady
ModeReady
00
01
10
11
ClkOut
-
-
-
-
-
-
-
-
-
-
-
-
PllLock
-
-
-
-
oMode
-
ModeReady
PllLock
PllLock
ModeReady
Rx
00
01
10
11
ClkOut
Rssi
T
imeou
t
Rssi
RxReady
toMode
imeout
D
Da
Data
Da
at
t
a
a
Dclk
RxReady
-
SyncAddress
RxReady
yncAddress
P
T
imeou
t
-
S
A
T
u
Rssi
ModeReady
PllLock
ModeReady
llLock
t
a
SyncAddress
Tx
00
01
10
11
ClkOut
ClkOut
-
T
T
xReady
xReady
-
T
T
xReady
xReady
Data
Data
Data
Data
Dclk
T
xReady
-
T
xReady
-
AutoMode
ModeReady
P
llLock
T
xReady
PllLock
ModeReady
5.3.2. DIO Pins Mapping in Packet Mode
Table 22 DIO Mapping, Packet Mode
Mode
Diox
Mapping
00
DIO5
DIO4
DIO3
DIO2
DIO1
DIO0
Sleep
-
-
-
-
-
-
-
-
-
-
-
Fif
o
-
-
-
F
ull
ull
ull
FifoNot
Emp
t
y
y
y
y
y
FifoLevel
FifoFull
oNotEmpty
-
-
-
-
-
-
-
-
-
01
10
11
-
-
Fi
Fi
Fi
Fi
Fi
f
ModeReady
AutoMode
Stdby
FS
00
01
10
11
ClkOu
t
Fif
Fif
o
F
FifoNotEmpt
FifoLevel
Fif ull
-
-
-
-
-
-
-
oF
f
oNotEmpty
-
ModeReady
AutoMode
00
01
10
11
ClkOu
t
-
-
-
o
F
FifoNotEmpt
FifoLevel
Fif ull
oNotEmpty
llLock
oLevel
FifoFull
-
-
-
-
-
-
-
-
-
oF
f
f
ModeReady
PllLock
P
llLock
oFull
Rssi
yncAddress
llLock
Fif ull
AutoMode
P
PllLock
Rx
00
01
10
11
00
01
10
11
ClkOut
Data
T
imeout
Rssi
Fif
Fif
oNotEmp
Data
-
t
F
i
f
CrcOk
ayloadReady
P
-
RxReady
llLock
ModeReady
S
oNotEmpty SyncAddress
ModeReady
P
P
AutoMode
FifoNotEmpt
Data
-
AutoMode
T
imeout
FifoLevel
FifoFull
Rssi
acketSent
xReady
-
PllLock
Tx
ClkOu
Data
-
t
o
F
P
T
xReady
-
T
xReady
-
T
f
oNotEmpty
llLock
ModeReady
PllLock
PllLock
P
Note Received Data is only shown on the Data signal between RxReady and PayloadReady’s rising edges
Page 48
Tel: +86-755-82973805 Fax: +86-755-82973550 E-mail: sales@hoperf.com http://www.hoperf.com
RFM69HW
ADVANCED COMMUNICATIONS & SENSING
DATASHEET
5.4. Continuous Mode
5.4.1. General Description
As illustrated in Figure 29, in Continuous mode the NRZ data to (from) the (de)modulator is directly accessed by the uC on
the bidirectional DIO2/DATA pin. The FIFO and packet handler are thus inactive.
DIO0
Tx/Rx
DIO1/DCLK
DIO2/DATA
DIO3
CONTROL
DIO4
DIO5
Data
Rx
SYNC
RECOG.
SPI
NSS
SCK
MOSI
MISO
Figure 29. Continuous Mode Conceptual View
5.4.2. Tx Processing
In Tx mode, a synchronous data clock for an external uC is provided on DIO1/DCLK pin. Clock timing with respect to the
data is illustrated in Figure 30. DATA is internally sampled on the rising edge of DCLK so the uC can change logic state
anytime outside the grayed out setup/hold zone.
T_DATA
T_DATA
DATA
(NRZ)
DCLK
Figure 30. Tx Processing in Continuous Mode
Note the use of DCLK is required when the modulation shaping is enabled (see section 3.3.5).
Page 49
Tel: +86-755-82973805 Fax: +86-755-82973550 E-mail: sales@hoperf.com http://www.hoperf.com
RFM69HW
ADVANCED COMMUNICATIONS & SENSING
DATASHEET
5.4.3. Rx Processing
If the bit synchronizer is disabled, the raw demodulator output is made directly available on DATA pin and no DCLK signal
is provided.
Conversely, if the bit synchronizer is enabled, synchronous cleaned data and clock are made available respectively on
DIO2/DATA and DIO1/DCLK pins. DATA is sampled on the rising edge of DCLK and updated on the falling edge as
illustrated below.
DATA (NRZ)
DCLK
Figure 31. Rx Processing in Continuous Mode
Note in Continuous mode it is always recommended to enable the bit synchronizer to clean the DATA signal even if the
DCLK signal is not used by the uC (bit synchronizer is automatically enabled in Packet mode).
5.5. Packet Mode
5.5.1. General Description
In Packet mode the NRZ data to (from) the (de)modulator is not directly accessed by the uC but stored in the FIFO and
accessed via the SPI interface.
In addition, the RFM69HW packet handler performs several packet oriented tasks such as Preamble and Sync word
generation, CRC calculation/check, whitening/dewhitening of data, Manchester encoding/decoding, address filtering, AES
encryption/decryption, etc. This simplifies software and reduces uC overhead by performing these repetitive tasks within
the RF module itself.
Another important feature is ability to fill and empty the FIFO in Sleep/Stdby mode, ensuring optimum power consumption
and adding more flexibility for the software.
Page 50
Tel: +86-755-82973805 Fax: +86-755-82973550 E-mail: sales@hoperf.com http://www.hoperf.com
RFM69HW
DVANCED COMMUNICATIONS & SENSING
DATASHEET
DIO0
DIO1
DIO2
DIO3
DIO4
DIO5
CONTROL
Data
Rx
Tx
SYNC
RECOG.
PACKET
HANDLER
FIFO
(+SR)
SPI
NSS
SCK
MOSI
MISO
Figure 32. Packet Mode Conceptual View
Note The Bit Synchronizer is automatically enabled in Packet mode.
5.5.2. Packet Format
5.5.2.1. Fixed Length Packet Format
Fixed length packet format is selected when bit PacketFormat is set to 0 and PayloadLength is set to any value greater
than 0.
In applications where the packet length is fixed in advance, this mode of operation may be of interest to minimize RF
overhead (no length byte field is required). All nodes, whether Tx only, Rx only, or Tx/Rx should be programmed with the
same packet length value.
The length of the payload is limited to 255 bytes if AES is not enabled else the message is limited to 64 bytes (i.e. max 65
bytes payload if Address byte is enabled).
The length programmed in PayloadLength relates only to the payload which includes the message and the optional
address byte. In this mode, the payload must contain at least one byte, i.e. address or message byte.
An illustration of a fixed length packet is shown below. It contains the following fields:
Preamble (1010...)
Sync word (Network ID)
Optional Address byte (Node ID)
Message data
Optional 2-bytes CRC checksum
Page 51
Tel: +86-755-82973805 Fax: +86-755-82973550 E-mail: sales@hoperf.com http://www.hoperf.com
RFM69HW
ADVANCED COMMUNICATIONS & SENSING
DATASHEET
DC free Data encoding
CRC checksum calcula ion
AES Enc Dec
t
/
Preamble
0 to 65535
bytes
Sync Word
0 to 8 bytes
Address
byte
Message
Up to 255 by
CRC
2-bytes
t
es
Payload
(min 1 byte)
Fields added by the packet handler in Tx and processed and removed in Rx
Optional User provided fields which are part of the payload
Message part of the payload
Figure 33. Fixed Length Packet Format
5.5.2.2. Variable Length Packet Format
Variable length packet format is selected when bit PacketFormat is set to 1.
This mode is useful in applications where the length of the packet is not known in advance and can vary over time. It is then
necessary for the transmitter to send the length information together with each packet in order for the receiver to operate
properly.
In this mode the length of the payload, indicated by the length byte, is given by the first byte of the FIFO and is limited to
255 bytes if AES is not enabled else the message is limited to 64 bytes (i.e. max 66 bytes payload if Address byte is
enabled). Note that the length byte itself is not included in its calculation. In this mode, the payload must contain at least 2
bytes, i.e. length + address or message byte.
An illustration of a variable length packet is shown below. It contains the following fields:
Preamble (1010...)
Sync word (Network ID)
Length byte
Optional Address byte (Node ID)
Message data
Optional 2-bytes CRC checksum
DC free Data encoding
CRC checksum calculation
AES Enc/Dec
Preamble
0 to 65535
bytes
Sync Word
0 to 8 bytes
Length
byte
Address
byte
Message
Up to 255 bytes
CRC
2-bytes
Payload
(min 2 bytes)
Fields added by the packet handler in Tx and processed and removed in Rx
Optional User provided fields which are part of the payload
Message part of the payload
Figure 34. Variable Length Packet Format
Page 52
Tel: +86-755-82973805 Fax: +86-755-82973550 E-mail: sales@hoperf.com http://www.hoperf.com
RFM69HW
ADVANCED COMMUNICATIONS & SENSING
DATASHEET
5.5.2.3. Unlimited Length Packet Format
Unlimited length packet format is selected when bit PacketFormat is set to 0 and PayloadLength is set to 0.
The user can then transmit and receive packet of arbitrary length and PayloadLength register is not used in Tx/Rx modes
for counting the length of the bytes transmitted/received. This mode is a replacement for the legacy buffered mode in
RF63/RF64 transceivers.
In Tx the data is transmitted depending on the TxStartCondition bit. On the Rx side the data processing features like
Address filtering, Manchester encoding and data whitening are not available if the sync pattern length is set to zero
(SyncOn = 0). The filling of the FIFO in this case can be controlled by the bit FifoFillCondition. The CRC detection in Rx is
also not supported in this mode of the packet handler, however CRC generation in Tx is operational. The interrupts like
CrcOk & PayloadReady are not available either.
An unlimited length packet shown in is made up of the following fields:
Preamble (1010...).
Sync word (Network ID).
Optional Address byte (Node ID).
Message data
Optional 2-bytes CRC checksum (Tx only)
DC free Data encoding
Preamble
0 to 65535
bytes
Sync
0 to 8 byte
W
ord
s
A
ddress
byt
Message
unlimited length
e
P
ayload
Fields added by the packet handler in Tx and processed and removed in Rx
Message part of the payload
Optional User provided fields which are part of the payload
Figure 35. Unlimited Length Packet Forma
t
5.5.3. Tx Processing (without AES)
In Tx mode the packet handler dynamically builds the packet by performing the following operations on the payload
available in the FIFO:
Add a programmable number of preamble bytes
Add a programmable Sync word
Optionally calculating CRC over complete payload field (optional length byte + optional address byte + message)
andappending the 2 bytes checksum.
Optional DC-free encoding of the data (Manchester or whitening)
Only the payload (including optional address and length fields) is required to be provided by the user in the FIFO.
Tel: +86-755-82973805 Fax: +86-755-82973550 E-mail: sales@hoperf.com http://www.hoperf.com
Page 53
RFM69HW
ADVANCED COMMUNICATIONS & SENSING
DATASHEET
The transmission of packet data is initiated by the Packet Handler only if the module is in Tx mode and the transmission
condition defined by TxStartCondition is fulfilled. If transmission condition is not fulfilled then the packet handler transmits a
preamble sequence until the condition is met. This happens only if the preamble length /= 0, otherwise it transmits a zero or
one until the condition is met to transmit the packet data.
The transmission condition itself is defined as:
if TxStartCondition = 1, the packet handler waits until the first byte is written into the FIFO, then it starts sending the
preamble followed by the sync word and user payload
If TxStartCondition = 0, the packet handler waits until the number of bytes written in the FIFO is equal to the number
defined in RegFifoThresh + 1
If the condition for transmission was already fulfilled i.e. the FIFO was filled in Sleep/Stdby then the transmission of
packet starts immediately on enabling Tx
5.5.4. Rx Processing (without AES)
In Rx mode the packet handler extracts the user payload to the FIFO by performing the following operations:
Receiving the preamble and stripping it off
Detecting the Sync word and stripping it off
Optional DC-free decoding of data
Optionally checking the address byte
Optionally checking CRC and reflecting the result on CrcOk.
Only the payload (including optional address and length fields) is made available in the FIFO.
When the Rx mode is enabled the demodulator receives the preamble followed by the detection of sync word. If fixed
length packet format is enabled then the number of bytes received as the payload is given by the PayloadLength
parameter.
In variable length mode the first byte received after the sync word is interpreted as the length of the received packet. The
internal length counter is initialized to this received length. The PayloadLength register is set to a value which is greater
than the maximum expected length of the received packet. If the received length is greater than the maximum length stored
in PayloadLength register the packet is discarded otherwise the complete packet is received.
If the address check is enabled then the second byte received in case of variable length and first byte in case of fixed
length is the address byte. If the address matches to the one in the NodeAddress field, reception of the data continues
otherwise it's stopped. The CRC check is performed if CrcOn = 1 and the result is available in CrcOk indicating that the
CRC was successful. An interrupt (PayloadReady) is also generated on DIO0 as soon as the payload is available in the
FIFO. The payload available in the FIFO can also be read in Sleep/Standby mode.
If the CRC fails the PayloadReady interrupt is not generated and the FIFO is cleared. This function can be overridden by
setting CrcAutoClearOff = 1, forcing the availability of PayloadReady interrupt and the payload in the FIFO even if the CRC
fails.
5.5.5. AES
AES is the symmetric-key block cipher that provides the cryptographic capabilities to the transceiver. The system proposed
can work with 128-bit long fixed keys. The fixed key is stored in a 16-byte write only user configuration register, which
retains its value in Sleep mode.
Page 54
Tel: +86-755-82973805 Fax: +86-755-82973550 E-mail: sales@hoperf.com http://www.hoperf.com
RFM69HW
As shown in Figure 33 and Figure 34 above the message part of the Packet can be encrypted and decrypted with the
cipher 128- cipher key stored in the configuration registers.
5.5.5.1. Tx Processing
1. User enters the data to be transmitted in FIFO in Stdby/Sleep mode and gives the transmit command.
2. On Tx command the Packet handler state machine takes over the control and If encryption is enabled then the
message inside the FIFO is read in blocks of 16 bytes (padded with 0s if needed), encrypted and stored back to FIFO.
All this processing is done in Tx mode before enabling the packet handling state machine. Only the Message part of the
packet is encrypted and preamble, sync word, length byte, address byte and CRC are not encrypted.
3. Once the encryption is done the Packet handling state machine is enabled to transmit the data.
5.5.5.2. Rx Processing
1. The data received is stored in the FIFO, The address, CRC interrupts are generated as usual because these
parameters were not encrypted.
2. Once the complete packet has been received. The data is read from the FIFO, decrypted and written back to FIFO.
The PayloadReady interrupt is issued once the decrypted data is ready in the FIFO for reading via the SPI interface.
The AES encryption/decryption cannot be used on the fly i.e. while transmitting and receiving data. Thus when AES
encryption/decryption is enabled, the FIFO acts as a simple buffer. This buffer is filled before initiating any transmission.
The data in the buffer is then encrypted before the transmission can begin. On the receive side the decryption is initiated
only once the complete packet has been received in the buffer.
The encryption/decryptionprocess takes approximately 7.0 us per 16-byte block. Thus for a maximum of 4 blocks (i.e. 64
bytes) it can take up to 28 us for completing the cryptographic operations.
The receive side sees the AES decryption time as a sequential delay before the PayloadReady interrupt is available.
The Tx side sees the AES encryption time as a sequential delay in the startup of the Tx chain, thus the startup time of the
Tx will increase according to the length of data.
In Fixed length mode the Message part of the payload that can be encrypted/decrypted can be 64 bytes long. If the
address filtering is enabled, the length of the payload should be at max 65 bytes in this case.
In Variable length mode the Max message size that can be encrypted/decrypted is also 64 bytes when address filtering is
disabled, else it is 48 bytes. Thus, including length byte, the length of the payload is max 65 or 50 bytes (the latter when
address filtering is enabled).
If the address filtering is expected then AddressFiltering must be enabled on the transmitter side as well to prevent address
byte to be encrypted.
Crc check being performed on encrypted data, CrcOk interrupt will occur "decryption time" before PayloadReady interrupt.
Page 55
Tel: +86-755-82973805 Fax: +86-755-82973550 E-mail: sales@hoperf.com http://www.hoperf.com
RFM69HW
ADVANCED COMMUNICATIONS & SENSING
DATASHEET
5.5.6. Handling Large Packets
When Payload length exceeds FIFO size (66 bytes) whether in fixed, variable or unlimited length packet format, in addition
to PacketSent in Tx and PayloadReady or CrcOk in Rx, the FIFO interrupts/flags can be used as described below:
For Tx:
FIFO can be prefilled in Sleep/Standby but must be refilled "on-the-fly" during Tx with the rest of the payload.
1) Prefill FIFO (in Sleep/Standby first or directly in Tx mode) until FifoThreshold or FifoFull is set
2) In Tx, wait for FifoThreshold or FifoNotEmpty to be cleared (i.e. FIFO is nearly empty)
3) Write bytes into the FIFO until FifoThreshold or FifoFull is set.
4) Continue to step 2 until the entire message has been written to the FIFO (PacketSent will fire when the last bit of the
packet has been sent).
For Rx:
FIFO must be unfilled "on-the-fly" during Rx to prevent FIFO overrun.
1) Start reading bytes from the FIFO when FifoNotEmpty or FifoThreshold becomes set.
2) Suspend reading from the FIFO if FifoNotEmpty clears before all bytes of the message have been read
3) Continue to step 1 until PayloadReady or CrcOk fires
4) Read all remaining bytes from the FIFO either in Rx or Sleep/Standby mode
Note AES encryption is not feasible on large packets, since all Payload bytes need to be in the FIFO at the same time to
perform encryption
5.5.7. Packet Filtering
RFM69HW's packet handler offers several mechanisms for packet filtering, ensuring that only useful packets are
made available to the uC, reducing significantly system power consumption and software complexity.
5.5.7.1. Sync Word Based
Sync word filtering/recognition is used for identifying the start of the payload and also for network identification. As
previously described, the Sync word recognition block is configured (size, error tolerance, value) in RegSyncValue
registers. This information is used, both for appending Sync word in Tx, and filtering packets in Rx.
Every received packet which does not start with this locally configured Sync word is automatically discarded and no
interrupt is generated.
When the Sync word is detected, payload reception automatically starts and SyncAddressMatch is asserted.
Note Sync Word values containing 0x00 byte(s) are forbidden
Page 56
Tel: +86-755-82973805 Fax: +86-755-82973550 E-mail: sales@hoperf.com http://www.hoperf.com
RFM69HW
ADVANCED COMMUNICATIONS & SENSING
DATASHEET
5.5.7.2. Address Based
Address filtering can be enabled via the AddressFiltering bits. It adds another level of filtering, above Sync word (i.e. Sync
must match first), typically useful in a multi-node networks where a network ID is shared between all nodes (Sync word)
and each node has its own ID (address).
Two address based filtering options are available:
AddressFiltering = 01: Received address field is compared with internal register NodeAddress. If they match then
packet is accepted and processed, otherwise it is discarded.
the
AddressFiltering = 10: Received address field is compared with internal registers NodeAddress and
BroadcastAddress.If either is a match, the received packet is accepted and processed, otherwise it is discarded.
This additional check with a constant is useful for implementing broadcast in a multi-node networks
Please note that the received address byte, as part of the payload, is not stripped off the packet and is made available in
the FIFO. In addition, NodeAddress and AddressFiltering only apply to Rx. On Tx side, if address filtering is expected, the
address byte should simply be put into the FIFO like any other byte of the payload.
As address filtering requires a Sync word match, both features share the same interrupt flag SyncAddressMatch.
5.5.7.3. Length Based
In variable length Packet mode, PayloadLength must be programmed with the maximum payload length permitted. If
received length byte is smaller than this maximum then the packet is accepted and processed, otherwise it is discarded.
Please note that the received length byte, as part of the payload, is not stripped off the packet and is made available in the
FIFO.
To disable this function the user should set the value of the PayloadLength to 255.
5.5.7.4. CRC Based
The CRC check is enabled by setting bit CrcOn in RegPacketConfig1. It is used for checking the integrity of the message.
On Tx side a two byte CRC checksum is calculated on the payload part of the packet and appended to the end of
the message
On Rx side the checksum is calculated on the received payload and compared with the two checksum bytes
received.The result of the comparison is stored in bit CrcOk.
By default, if the CRC check fails then the FIFO is automatically cleared and no interrupt is generated. This filtering function
can be disabled via CrcAutoClearOff bit and in this case, even if CRC fails, the FIFO is not cleared and only PayloadReady
interrupt goes high. Please note that in both cases, the two CRC checksum bytes are stripped off by the packet handler
and only the payload is made available in the FIFO.
The CRC is based on the CCITT polynomial as shown below. This implementation also detects errors due to leading and
trailing zeros.
Page 57
Tel: +86-755-82973805 Fax: +86-755-82973550 E-mail: sales@hoperf.com http://www.hoperf.com
RFM69HW
ADVANCED COMMUNICATIONS & SENSING
DATASHEET
CRC Polynomial =X16 + X12 + X5 +
1
data input
X14
X13
X12
X15
X5
X0
X11
X4
* * *
* * *
Figure 36. CRC Implementation
5.5.8. DC-Free Data Mechanisms
The payload to be transmitted may contain long sequences of 1's and 0's, which introduces a DC bias in the transmitted
signal. The radio signal thus produced has a non uniform power distribution over the occupied channel bandwidth. It also
introduces data dependencies in the normal operation of the demodulator. Thus it is useful if the transmitted data is random
and DC free.
For such purposes, two techniques are made available in the packet handler: Manchester encoding and data whitening.
Note Only one of the two methods should be enabled at a time.
5.5.8.1. Manchester Encoding
Manchester encoding/decoding is enabled if DcFree = 01 and can only be used in Packet mode.
The NRZ data is converted to Manchester code by coding '1' as "10" and '0' as "01".
In this case, the maximum chip rate is the maximum bit rate given in the specifications section and the actual bit rate is half
the chip rate.
Manchester encoding and decoding is only applied to the payload and CRC checksum while preamble and Sync word are
kept NRZ. However, the chip rate from preamble to CRC is the same and defined by BitRate in RegBitRate (Chip Rate =
Bit Rate NRZ = 2 x Bit Rate Manchester).
Manchester encoding/decoding is thus made transparent for the user, who still provides/retrieves NRZ data to/from the
FIFO
1/BR
1/BR
...Sync
Payload...
RF chips @ BR
User/NRZ bits
Manchester OFF
User/NRZ bits
Manchester ON
...
1
1
1
0
1
0
0
1
0
0
1
0
1
1
0
1
0
...
t
...
1
1
1
1
0
1
0
0
1
0
0
1
0
1
1
0
1
0
...
...
1
1
0
1
0
0
1
0
0
1
1
...
Figure 37. Manchester Encoding/Decoding
Page 58
Tel: +86-755-82973805 Fax: +86-755-82973550 E-mail: sales@hoperf.com http://www.hoperf.com
RFM69HW
ADVANCED COMMUNICATIONS & SENSING
DATASHEET
5.5.8.2. Data Whitening
Another technique called whitening or scrambling is widely used for randomizing the user data before radio transmission.
The data is whitened using a random sequence on the Tx side and de-whitened on the Rx side using the same sequence.
Comparing to Manchester technique it has the advantage of keeping NRZ data rate i.e. actual bit rate is not halved.
The whitening/de-whitening process is enabled if DcFree = 10. A 9-bit LFSR is used to generate a random sequence. The
payload and 2-byte CRC checksum is then XORed with this random sequence as shown below. The data is de-whitened
on the receiver side by XORing with the same random sequence.
Payload whitening/de-whitening is thus made transparent for the user, who still provides/retrieves NRZ data to/from the
FIFO.
LFS
R
Polynom ia
l
=X9
+
X5
+ 1
X8
X7
X6
X 5
X4
X3
X2
X1
X 0
W
hitened data
Transm it data
Figure 38. Data Whitening
Page 59
Tel: +86-755-82973805 Fax: +86-755-82973550 E-mail: sales@hoperf.com http://www.hoperf.com
RFM69HW
ADVANCED COMMUNICATIONS & SENSING
6. Configuration and Status Registers
DATASHEET
6.1. General Description
Table 23 Registers Summary
Default
Reset
Address
Register Name
(recom
Description
(built-in)
mended)
0x00
0x01
0x02
0x03
0x04
0x05
0x06
0x07
0x08
0x09
0x0A
0x0B
0x0C
0x0D
0x0E
0x0F
0x10
0x11
0x12
0x13
0x14
RegFifo
RegOpMode
RegDataModul
RegBitrateMsb
RegBitrateLsb
RegFdevMsb
RegFdevLsb
RegFrfMsb
RegFrfMid
0x00
FIFO read/write access
Operating modes of the transceiver
0x04
0x00
0x1A
0x0B
0x00
0x52
0xE4
0xC0
0x00
0x41
0x00
0x02
0x92
0xF5
0x20
0x24
0x9F
0x09
0x1A
0x40
Data operation mode and Modulation settings
Bit Rate setting, Most Significant Bits
Bit Rate setting, Least Significant Bits
Frequency Deviation setting, Most Significant Bits
Frequency Deviation setting, Least Significant Bits
RF Carrier Frequency, Most Significant Bits
RF Carrier Frequency, Intermediate Bits
RF Carrier Frequency, Least Significant Bits
RC Oscillators Settings
RegFrfLsb
RegOsc1
RegAfcCtrl
AFC control in low modulation index situations
-
Reserved0C
RegListen1
RegListen2
RegListen3
RegVersion
RegPaLevel
RegPaRamp
RegOcp
Listen Mode settings
Listen Mode Idle duration
Listen Mode Rx duration
PA selection and Output Power control
Control of the PA ramp time in FSK mode
Over Current Protection control
Reserved14
-
-
0x15
0x16
Reserved15
Reserved16
0xB0
0x7B
0x9B
-
0x17
0x18
Reserved17
RegLna
-
0x08
0x86
0x88
0x55
LNA settings
0x19
RegRxBw
Channel Filter BW Control
Page 60
Tel: +86-755-82973805 Fax: +86-755-82973550 E-mail: sales@hoperf.com http://www.hoperf.com
RFM69HW
ADVANCED COMMUNICATIONS & SENSING
DATASHEET
Default
Reset
Address
Register Name
(recom
Description
(built-in)
mended)
0x1A
RegAfcBw
0x8A
0x8B
Channel Filter BW control during the AFC routine
0x1B
0x1C
0x1D
0x1E
0x1F
0x20
0x21
0x22
0x23
0x24
0x25
0x26
RegOokPeak
RegOokAvg
RegOokFix
0x40
OOK demodulator selection and control in peak mode
Average threshold control of the OOK demodulator
Fixed threshold control of the OOK demodulator
AFC and FEI control and status
0x80
0x06
0x10
0x00
0x00
0x00
0x00
0x02
0xFF
0x00
RegAfcFei
RegAfcMsb
MSB of the frequency correction of the AFC
LSB of the frequency correction of the AFC
MSB of the calculated frequency error
LSB of the calculated frequency error
RSSI-related settings
RegAfcLsb
RegFeiMsb
RegFeiLsb
RegRssiConfig
RegRssiValue
RegDioMapping1
RegDioMapping2
RSSI value in dBm
Mapping of pins DIO0 to DIO3
0x05
0xFF
0x07
0xE4
Mapping of pins DIO4 and DIO5, ClkOut frequency
0x27
0x28
0x29
RegIrqFlags1
RegIrqFlags2
RegRssiThresh
0x80
0x00
Status register: PLL Lock state, Timeout, RSSI > Threshold...
Status register: FIFO handling flags...
RSSI Threshold control
0x2A
0x2B
RegRxTimeout1
RegRxTimeout2
RegPreambleMsb
RegPreambleLsb
RegSyncConfig
RegSyncValue1-8
0x00
0x00
0x00
0x03
0x98
Timeout duration between Rx request and RSSI detection
Timeout duration between RSSI detection and PayloadReady
Preamble length, MSB
0x2C
0x2D
Preamble length, LSB
0x2E
Sync Word Recognition control
0x2F-0x36
0x00
0x01
Sync Word bytes, 1 through 8
0x37
0x38
0x39
0x3A
0x3B
0x3C
RegPacketConfig1
RegPayloadLength
RegNodeAdrs
0x10
0x40
0x00
0x00
0x00
Packet mode settings
Payload length setting
Node address
RegBroadcastAdrs
RegAutoModes
RegFifoThresh
Broadcast address
Auto modes settings
0x0F
0x8F
Fifo threshold, Tx start condition
Packet mode settings
0x3D
RegPacketConfig2
0x02
Page 61
Tel: +86-755-82973805 Fax: +86-755-82973550 E-mail: sales@hoperf.com http://www.hoperf.com
RFM69HW
Default
(recom
mended)
Reset
(built-in)
Address
Register Name
Description
0x3E-0x4D
0x4E
RegAesKey1-16
RegTemp1
0x00
16 bytes of the cypher key
0x01
0x00
0x1B
0x55
0x70
Temperature Sensor control
Temperature readout
Sensitivity boost
0x4F
RegTemp2
0x58
RegTestLna
RegTestPa1
RegTestPa2
RegTestDagc
0x5A
High Power PA settings
High Power PA settings
0x5C
0x6F
0x00
0x30
Fading Margin Improvement
0x71
RegTestAfc
RegTest
0x00
-
AFC offset for low modulation index AFC
Internal test registers
0x50 +
Note - Reset values are automatically refreshed in the chip at Power On Reset
- Default values are recommended register values, optimizing the device operation
- Registers for which the Default value differs from the Reset value are denoted by a * in the tables of section 6
Page 62
Tel: +86-755-82973805 Fax: +86-755-82973550 E-mail: sales@hoperf.com http://www.hoperf.com
RFM69HW
6.2. Common Configuration Registers
Table 24 Common Configuration Registers
Name
Default
Value
Bits Variable Name
(Address)
Mode
Description
7-0 Fifo
rw
0x00 FIFO data input/output
RegFifo
(0x00)
7
6
5
SequencerOff
rw
rw
0
0
Controls the automatic Sequencer (see section 4.2 ):
0 → Operating mode as selected with Mode bits in
RegOpMode is automatically reached with the Sequencer
1 → Mode is forced by the user
RegOpMode
(0x01)
ListenOn
Enables Listen mode, should be enabled whilst in
Standby mode:
0 → Off (see section 4.3)
1 → On
ListenAbort
w
0
Aborts Listen mode when set together with ListenOn=0
See section 4.3.4 for details
Always reads 0.
4-2 Mode
rw
001
Transceiver’s operating modes:
000 → Sleep mode (SLEEP)
001 → Standby mode (STDBY)
010 → Frequency Synthesizer mode (FS)
011 → Transmitter mode (TX)
100 → Receiver mode (RX)
; Reads the value corresponding to
others → reserved
the current module mode
1-0
7
-
-
r
r
00
0
unused
unused
RegDataModul
(0x02)
6-5 DataMode
rw
00
Data processing mode:
00 → Packet mode
01 → reserved
10 → Continuous mode with bit synchronizer
11 → Continuous mode without bit synchronizer
4-3 ModulationType
rw
00
Modulation scheme:
00 → FSK
01 → OOK
10 - 11 → reserved
2
-
r
0
unused
1-0 ModulationShaping
rw
00
Data shaping:
in FSK:
00 → no shaping
01 → Gaussian filter, BT = 1.0
10 → Gaussian filter, BT = 0.5
11 → Gaussian filter, BT = 0.3
in OOK:
00 → no shaping
01 → filtering with fcutoff = BR
10 → filtering with fcutoff = 2*BR
11 → reserved
7-0 BitRate(15:8)
rw
0x1a MSB of Bit Rate (Chip Rate when Manchester encoding is
enabled)
RegBitrateMsb
(0x03)
Page 63
Tel: +86-755-82973805 Fax: +86-755-82973550 E-mail: sales@hoperf.com http://www.hoperf.com
RFM69HW
ADVANCED COMMUNICATIONS & SENSING
DATASHEET
7-0 BitRate(7:0)
rw
0x0b LSB of Bit Rate (Chip Rate if Manchester encoding is
RegBitrateLsb
(0x04)
enabled)
FXO SC
BitRate(15,0)
----------------------------------
BitRate =
Default value: 4.8 kb/s
unused
7-6
-
r
00
RegFdevMsb
(0x05)
5-0 Fdev(13:8)
7-0 Fdev(7:0)
rw
rw
000000 MSB of the frequency deviation
0x52 LSB of the frequency deviation
RegFdevLsb
(0x06)
Fdev = Fstep
⋅Fdev(15,0)
Default value: 5 kHz
7-0 Frf(23:16)
7-0 Frf(15:8)
7-0 Frf(7:0)
rw
rw
rw
0xe4 MSB of the RF carrier frequency
RegFrfMsb
(0x07)
0xc0 Middle byte of the RF carrier frequency
0x00 LSB of the RF carrier frequency
RegFrfMid
(0x08)
RegFrfLsb
(0x09)
Frf = Fstep
⋅Frf 23;0
Default value: Frf = 915 MHz (32 MHz XO)
7
6
RcCalStart
RcCalDone
w
r
0
1
Triggers the calibration of the RC oscillator when set.
Always reads 0. RC calibration must be triggered in
Standby mode.
RegOsc1
(0x0A)
0 → RC calibration in progress
1 → RC calibration is over
5-0
7-6
5
-
r
r
000001 unused
-
00
0
unused
RegAfcCtrl
(0x0B)
AfcLowBetaOn
rw
Improved AFC routine for signals with modulation index
lower than 2. Refer to section 3.4.16 for details
0 → Standard AFC routine
1 → Improved AFC routine
4-0
7-0
-
-
r
r
00000 unused
0x02 unused
Reserved0C
(0x0C)
Page 64
Tel: +86-755-82973805 Fax: +86-755-82973550 E-mail: sales@hoperf.com http://www.hoperf.com
RFM69HW
ADVANCED COMMUNICATIONS & SENSING
DATASHEET
7-6 ListenResolIdle
rw
10
01
Resolution of Listen mode Idle time (calibrated RC osc):
00 → reserved
01 → 64 us
10 → 4.1 ms
11 → 262 ms
RegListen1
(0x0D)
5-4 ListenResolRx
rw
Resolution of Listen mode Rx time (calibrated RC osc):
00 → reserved
01 → 64 us
10 → 4.1 ms
11 → 262 ms
3
ListenCriteria
rw
rw
0
Criteria for packet acceptance in Listen mode:
0 → signal strength is above RssiThreshold
1 → signal strength is above RssiThreshold and
SyncAddress matched
2-1 ListenEnd
01
Action taken after acceptance of a packet in Listen mode:
00 → chip stays in Rx mode. Listen mode stops and must
be disabled (see section 4.3).
01 → chip stays in Rx mode until PayloadReady or
Timeout interrupt occurs. It then goes to the mode defined
by Mode. Listen mode stops and must be disabled (see
section 4.3).
10 → chip stays in Rx mode until PayloadReady or
Timeout interrupt occurs. Listen mode then resumes in
Idle state. FIFO content is lost at next Rx wakeup.
11 → Reserved
0
-
r
0
unused
7-0 ListenCoefIdle
rw
0xf5 Duration of the Idle phase in Listen mode.
RegListen2
(0x0E)
t
= ListenCoefIdle∗ListenResolIdle
ListenIdle
7-0 ListenCoefRx
rw
0x20 Duration of the Rx phase in Listen mode (startup time
included, see section 4.2.3)
RegListen3
(0x0F)
t
= ListenCoefRx∗ ListenResolRx
ListenRx
RegVersion
(0x10)
Version code of the chip. Bits 7-4 give the full revision
number; bits 3-0 give the metal mask revision number.
7-0 Version
r
0x24
Page 65
Tel: +86-755-82973805 Fax: +86-755-82973550 E-mail: sales@hoperf.com http://www.hoperf.com
RFM69HW
ADVANCED COMMUNICATIONS & SENSING
DATASHEET
6.3. Transmitter Registers
Table 25 Transmitter Registers
Name
(Address)
Default
Value
Bits Variable Name
Mode
Description
7
6
5
Pa0On *
Pa1On *
Pa2On *
rw
rw
rw
rw
1
0
0
Enables PA0, connected to RFIO and LNA
Enables PA1, on PA_BOOST pin
Enables PA2, on PA_BOOST pin
RegPaLevel
(0x11)
4-0 OutputPower
11111 Output power setting, with 1 dB steps
Pout = -18 + OutputPower [dBm] , with PA0
Pout = -18 + OutputPower [dBm] , with PA1**
Pout = -14+ OutputPower [dBm] , with PA1 and PA2**
Pout = -11 + OutputPower [dBm] , with PA1 and PA2, and
high Power PA settings (refer to section 3.3.7)**
7-4
-
r
0000 unused
RegPaRamp
(0x12)
3-0 PaRamp
rw
1001 Rise/Fall time of ramp up/down in FSK
0000 → 3.4 ms
0001 → 2 ms
0010 → 1 ms
0011 → 500 us
0100 → 250 us
0101 → 125 us
0110 → 100 us
0111 → 62 us
1000 → 50 us
1001 → 40 us
1010 → 31 us
1011 → 25 us
1100 → 20 us
1101 → 15 us
1110 → 12 us
1111 → 10 us
7-5
4
-
r
000
1
unused
RegOcp
(0x13)
OcpOn
rw
Enables overload current protection (OCP) for the PA:
0 → OCP disabled
1 → OCP enabled
3-0 OcpTrim
rw
1010 Trimming of OCP current:
Imax = 45 + 5 OcpTrim mA
95 mA OCP by default
⋅
Note *Power Amplifier truth table is available in Table 10
** Only the16 upper values of OutputPower are accessible
Page 66
Tel: +86-755-82973805 Fax: +86-755-82973550 E-mail: sales@hoperf.com http://www.hoperf.com
RFM69HW
ADVANCED COMMUNICATIONS & SENSING
DATASHEET
6.4. Receiver Registers
Table 26 Receiver Registers
Name
(Address)
Default
Value
Bits Variable Name
Mode
Description
7-0
7-0
7-0
7-0
7
-
r
0x40 unused
0xB0 unused
0x7B unused
0x9B unused
Reserved14
(0x14)
-
r
r
Reserved15
(0x15)
-
Reserved16
(0x16)
-
r
Reserved17
(0x17)
LnaZin
rw
1
*
LNA’s input impedance
0 → 50 ohms
1 → 200 ohms
RegLna
(0x18)
6
-
r
r
0
unused
5-3 LnaCurrentGain
2-0 LnaGainSelect
001
000
Current LNA gain, set either manually, or by the AGC
rw
LNA gain setting:
000 → gain set by the internal AGC loop
001 → G1 = highest gain
010 → G2 = highest gain – 6 dB
011 → G3 = highest gain – 12 dB
100 → G4 = highest gain – 24 dB
101 → G5 = highest gain – 36 dB
110 → G6 = highest gain – 48 dB
111 → reserved
7-5 DccFreq
rw
010
*
Cut-off frequency of the DC offset canceller (DCC):
RegRxBw
(0x19)
~4% of the RxBw by default
4-3 RxBwMant
2-0 RxBwExp
rw
rw
10
*
Channel filter bandwidth control:
00 → RxBwMant = 16
01 → RxBwMant = 20
10 → RxBwMant = 24
11 → reserved
101
*
Channel filter bandwidth control:
FSK Mode:
FXOSC
-----------------------------------------------------------------
RxBw =
RxBwMant
∗
2RxBwExp + 2
OOK Mode:
RxBw =
FXOSC
-----------------------------------------------------------------
RxBwMant
2RxBwExp + 3
∗
See Table 14 for tabulated values
7-5 DccFreqAfc
4-3 RxBwMantAfc
2-0 RxBwExpAfc
rw
rw
rw
100
01
DccFreq parameter used during the AFC
RxBwMant parameter used during the AFC
RegAfcBw
(0x1A)
011 * RxBwExp parameter used during the AFC
Page 67
Tel: +86-755-82973805 Fax: +86-755-82973550 E-mail: sales@hoperf.com http://www.hoperf.com
RFM69HW
ADVANCED COMMUNICATIONS & SENSING
DATASHEET
7-6 OokThreshType
rw
rw
01
Selects type of threshold in the OOK data slicer:
RegOokPeak
(0x1B)
00 → fixed
01 → peak
10 → average
11 → reserved
5-3 OokPeakTheshStep
000
Size of each decrement of the RSSI threshold in the OOK
demodulator:
000 → 0.5 dB
010 → 1.5 dB
100 → 3.0 dB
110 → 5.0 dB
001 → 1.0 dB
011 → 2.0 dB
101 → 4.0 dB
111 → 6.0 dB
2-0 OokPeakThreshDec
7-6 OokAverageThreshFilt
rw
rw
000
10
Period of decrement of the RSSI threshold in the OOK
demodulator:
000 → once per chip
010 → once every 4 chips
100 → twice in each chip
001 → once every 2 chips
011 → once every 8 chips
101 → 4 times in each chip
110 → 8 times in each chip 111 → 16 times in each chip
Filter coefficients in average mode of the OOK
demodulator:
RegOokAvg
(0x1C)
00 → f ≈ chip rate / 32.π
01 → f ≈ chip rate / 8.π
C
C
10 → f ≈ chip rate / 4.π
11 →f ≈ chip rate / 2.π
C
C
5-0
-
r
000000 unused
7-0 OokFixedThresh
rw
0110 Fixed threshold value (in dB) in the OOK demodulator.
(6dB) Used when OokThresType = 00
RegOokFix
(0x1D)
7
6
-
r
r
0
0
unused
RegAfcFei
(0x1E)
FeiDone
0 → FEI is on-going
1 → FEI finished
5
4
FeiStart
w
r
0
1
Triggers a FEI measurement when set. Always reads 0.
AfcDone
0 → AFC is on-going
1 → AFC has finished
3
2
AfcAutoclearOn
AfcAutoOn
rw
rw
0
0
Only valid if AfcAutoOn is set
0 → AFC register is not cleared before a new AFC phase
1 → AFC register is cleared before a new AFC phase
0 → AFC is performed each time AfcStart is set
1 → AFC is performed each time Rx mode is entered
1
0
AfcClear
AfcStart
w
w
r
0
0
Clears the AfcValue if set in Rx mode. Always reads 0
Triggers an AFC when set. Always reads 0.
7-0 AfcValue(15:8)
7-0 AfcValue(7:0)
7-0 FeiValue(15:8)
7-0 FeiValue(7:0)
0x00 MSB of the AfcValue, 2’s complement format
RegAfcMsb
(0x1F)
r
r
r
0x00 LSB of the AfcValue, 2’s complement format
RegAfcLsb
(0x20)
Frequency correction = AfcValue x Fstep
-
-
MSB of the measured frequency offset, 2’s complement
RegFeiMsb
(0x21)
LSB of the measured frequency offset, 2’s complement
RegFeiLsb
(0x22)
Frequency error = FeiValue x Fstep
7-2
1
-
r
r
000000 unused
RegRssiConfig
(0x23)
RssiDone
1
0 → RSSI is on-going
1 → RSSI sampling is finished, result available
0
RssiStart
w
r
0
Trigger a RSSI measurement when set. Always reads 0.
7-0 RssiValue
0xFF Absolute value of the RSSI in dBm, 0.5dB steps.
RegRssiValue
(0x24)
RSSI = -RssiValue/2 [dBm]
Page 68
Tel: +86-755-82973805 Fax: +86-755-82973550 E-mail: sales@hoperf.com http://www.hoperf.com
RFM69HW
ADVANCED COMMUNICATIONS & SENSING
DATASHEET
6.5. IRQ and Pin Mapping Registers
Table 27 IRQ and Pin Mapping Registers
Name
(Address)
Default
Value
Bits Variable Name
Mode
Description
7-6 Dio0Mapping
5-4 Dio1Mapping
3-2 Dio2Mapping
1-0 Dio3Mapping
7-6 Dio4Mapping
5-4 Dio5Mapping
rw
rw
rw
rw
rw
rw
r
00
RegDioMapping1
(0x25)
Mapping of pins DIO0 to DIO5
00
00
See Table 21 for mapping in Continuous mode
See Table 22 for mapping in Packet mode
00
00
RegDioMapping2
(0x26)
00
3
-
0
unused
2-0 ClkOut
rw
111
*
Selects CLKOUT frequency:
000 → FXOSC
001 → FXOSC / 2
010 → FXOSC / 4
011 → FXOSC / 8
100 → FXOSC / 16
101 → FXOSC / 32
110 → RC (automatically enabled)
111 → OFF
7
ModeReady
r
1
Set when the operation mode requested in Mode, is ready
- Sleep: Entering Sleep mode
- Standby: XO is running
RegIrqFlags1
(0x27)
- FS: PLL is locked
- Rx: RSSI sampling starts
- Tx: PA ramp-up completed
Cleared when changing operating mode.
6
5
4
3
2
RxReady
TxReady
PllLock
Rssi
r
0
0
0
0
0
Set in Rx mode, after RSSI, AGC and AFC.
Cleared when leaving Rx.
r
r
Set in Tx mode, after PA ramp-up.
Cleared when leaving Tx.
Set (in FS, Rx or Tx) when the PLL is locked.
Cleared when it is not.
rwc
r
Set in Rx when the RssiValue exceeds RssiThreshold.
Cleared when leaving Rx.
Timeout
Set when a timeout occurs (see TimeoutRxStart and
TimeoutRssiThresh)
Cleared when leaving Rx or FIFO is emptied.
1
0
AutoMode
r
0
0
Set when entering Intermediate mode.
Cleared when exiting Intermediate mode.
Please note that in Sleep mode a small delay can be
observed between AutoMode interrupt and the
corresponding enter/exit condition.
SyncAddressMatch
r/rwc
Set when Sync and Address (if enabled) are detected.
Cleared when leaving Rx or FIFO is emptied.
This bit is read only in Packet mode, rwc in Continuous
mode
Page 69
Tel: +86-755-82973805 Fax: +86-755-82973550 E-mail: sales@hoperf.com http://www.hoperf.com
RFM69HW
ADVANCED COMMUNICATIONS & SENSING
DATASHEET
7
FifoFull
r
0
Set when FIFO is full (i.e. contains 66 bytes), else
cleared.
RegIrqFlags2
(0x28)
6
5
FifoNotEmpty
FifoLevel
r
r
0
0
Set when FIFO contains at least one byte, else cleared
Set when the number of bytes in the FIFO strictly exceeds
FifoThreshold, else cleared.
4
FifoOverrun
rwc
0
Set when FIFO overrun occurs. (except in Sleep mode)
Flag(s) and FIFO are cleared when this bit is set. The
FIFO then becomes immediately available for the next
transmission / reception.
3
2
PacketSent
r
r
0
0
Set in Tx when the complete packet has been sent.
Cleared when exiting Tx.
PayloadReady
Set in Rx when the payload is ready (i.e. last byte
received and CRC, if enabled and CrcAutoClearOff is
cleared, is Ok). Cleared when FIFO is empty.
1
0
CrcOk
-
r
0
0
Set in Rx when the CRC of the payload is Ok. Cleared
when FIFO is empty.
r
unused
7-0 RssiThreshold
rw
0xE4 RSSI trigger level for Rssi interrupt :
RegRssiThresh
(0x29)
*
- RssiThreshold / 2 [dBm]
7-0 TimeoutRxStart
rw
rw
0x00
Timeout interrupt is generated TimeoutRxStart*16*T
after switching to Rx mode if Rssi interrupt doesn’t occur
(i.e. RssiValue > RssiThreshold)
RegRxTimeout1
(0x2A)
bit
0x00: TimeoutRxStart is disabled
7-0 TimeoutRssiThresh
0x00
Timeout interrupt is generated TimeoutRssiThresh*16*T
after Rssi interrupt if PayloadReady interrupt doesn’t
occur.
RegRxTimeout2
(0x2B)
bit
0x00: TimeoutRssiThresh is disabled
Page 70
Tel: +86-755-82973805 Fax: +86-755-82973550 E-mail: sales@hoperf.com http://www.hoperf.com
RFM69HW
ADVANCED COMMUNICATIONS & SENSING
DATASHEET
6.6. Packet Engine Registers
Table 28 Packet Engine Registers
Name
(Address)
Default
Value
Bits Variable Name
Mode
Description
7-0 PreambleSize(15:8)
rw
0x00 Size of the preamble to be sent (from TxStartCondition
RegPreambleMsb
(0x2c)
fulfilled). (MSB byte)
7-0 PreambleSize(7:0)
rw
rw
0x03 Size of the preamble to be sent (from TxStartCondition
RegPreambleLsb
(0x2d)
fulfilled). (LSB byte)
7
6
SyncOn
1
0
Enables the Sync word generation and detection:
0 → Off
1 → On
RegSyncConfig
(0x2e)
FifoFillCondition
rw
rw
FIFO filling condition:
0 → if SyncAddress interrupt occurs
1 → as long as FifoFillCondition is set
5-3 SyncSize
011
000
Size of the Sync word:
(SyncSize + 1) bytes
2-0 SyncTol
rw
rw
Number of tolerated bit errors in Sync word
1st byte of Sync word. (MSB byte)
Used if SyncOn is set.
7-0 SyncValue(63:56)
0x01
*
RegSyncValue1
(0x2f)
2nd byte of Sync word
Used if SyncOn is set and (SyncSize +1) >= 2.
3rd byte of Sync word.
Used if SyncOn is set and (SyncSize +1) >= 3.
4th byte of Sync word.
Used if SyncOn is set and (SyncSize +1) >= 4.
5th byte of Sync word.
Used if SyncOn is set and (SyncSize +1) >= 5.
6th byte of Sync word.
Used if SyncOn is set and (SyncSize +1) >= 6.
7th byte of Sync word.
Used if SyncOn is set and (SyncSize +1) >= 7.
8th byte of Sync word.
Used if SyncOn is set and (SyncSize +1) = 8.
7-0 SyncValue(55:48)
7-0 SyncValue(47:40)
7-0 SyncValue(39:32)
7-0 SyncValue(31:24)
7-0 SyncValue(23:16)
7-0 SyncValue(15:8)
7-0 SyncValue(7:0)
rw
rw
rw
rw
rw
rw
rw
0x01
*
RegSyncValue2
(0x30)
0x01
*
RegSyncValue3
(0x31)
0x01
*
RegSyncValue4
(0x32)
0x01
*
RegSyncValue5
(0x33)
0x01
*
RegSyncValue6
(0x34)
0x01
*
RegSyncValue7
(0x35)
0x01
*
RegSyncValue8
(0x36)
Page 71
Tel: +86-755-82973805 Fax: +86-755-82973550 E-mail: sales@hoperf.com http://www.hoperf.com
RFM69HW
ADVANCED COMMUNICATIONS & SENSING
DATASHEET
7
PacketFormat
rw
rw
0
Defines the packet format used:
0 → Fixed length
1 → Variable length
RegPacketConfig1
(0x37)
6-5 DcFree
00
Defines DC-free encoding/decoding performed:
00 → None (Off)
01 → Manchester
10 → Whitening
11 → reserved
4
3
CrcOn
rw
rw
1
0
Enables CRC calculation/check (Tx/Rx):
0 → Off
1 → On
CrcAutoClearOff
Defines the behavior of the packet handler when CRC
check fails:
0 → Clear FIFO and restart new packet reception. No
PayloadReady interrupt issued.
1 → Do not clear FIFO. PayloadReady interrupt issued.
2-1 AddressFiltering
rw
00
Defines address based filtering in Rx:
00 → None (Off)
01 → Address field must match NodeAddress
10 → Address field must match NodeAddress or
BroadcastAddress
11 → reserved
0
-
rw
rw
0
unused
7-0 PayloadLength
0x40 If PacketFormat = 0 (fixed), payload length.
If PacketFormat = 1 (variable), max length in Rx, not used
in Tx.
RegPayloadLength
(0x38)
7-0 NodeAddress
rw
rw
rw
0x00 Node address used in address filtering.
RegNodeAdrs
(0x39)
7-0 BroadcastAddress
7-5 EnterCondition
0x00 Broadcast address used in address filtering.
RegBroadcastAdrs
(0x3A)
000
000
00
Interrupt condition for entering the intermediate mode:
000 → None (AutoModes Off)
001 → Rising edge of FifoNotEmpty
010 → Rising edge of FifoLevel
RegAutoModes
(0x3B)
011 → Rising edge of CrcOk
100 → Rising edge of PayloadReady
101 → Rising edge of SyncAddress
110 → Rising edge of PacketSent
111 → Falling edge of FifoNotEmpty (i.e. FIFO empty)
4-2 ExitCondition
rw
Interrupt condition for exiting the intermediate mode:
000 → None (AutoModes Off)
001 → Falling edge of FifoNotEmpty (i.e. FIFO empty)
010 → Rising edge of FifoLevel or Timeout
011 → Rising edge of CrcOk or Timeout
100 → Rising edge of PayloadReady or Timeout
101 → Rising edge of SyncAddress or Timeout
110 → Rising edge of PacketSent
111 → Rising edge of Timeout
1-0 IntermediateMode
rw
Intermediate mode:
00 → Sleep mode (SLEEP)
01 → Standby mode (STDBY)
10 → Receiver mode (RX)
11 → Transmitter mode (TX)
Page 72
Tel: +86-755-82973805 Fax: +86-755-82973550 E-mail: sales@hoperf.com http://www.hoperf.com
RFM69HW
ADVANCED COMMUNICATIONS & SENSING
DATASHEET
7
TxStartCondition
rw
1
*
Defines the condition to start packet transmission :
0 → FifoLevel (i.e. the number of bytes in the FIFO
exceeds FifoThreshold)
RegFifoThresh
(0x3C)
1 → FifoNotEmpty (i.e. at least one byte in the FIFO)
6-0 FifoThreshold
rw
rw
0001111 Used to trigger FifoLevel interrupt.
7-4 InterPacketRxDelay
0000 After PayloadReady occurred, defines the delay between
FIFO empty and the start of a new RSSI phase for next
packet. Must match the transmitter’s PA ramp-down time.
- Tdelay = 0 if InterpacketRxDelay >= 12
RegPacketConfig2
(0x3D)
- Tdelay = (2InterpacketRxDelay) / BitRate otherwise
3
2
-
rw
w
0
0
unused
RestartRx
Forces the Receiver in WAIT mode, in Continuous Rx
mode.
Always reads 0.
1
AutoRxRestartOn
rw
1
Enables automatic Rx restart (RSSI phase) after
PayloadReady occurred and packet has been completely
read from FIFO:
0 → Off. RestartRx can be used.
1 → On. Rx automatically restarted after
InterPacketRxDelay.
0
AesOn
rw
0
Enable the AES encryption/decryption:
0 → Off
1 → On (payload limited to 66 bytes maximum)
1st byte of cipher key (MSB byte)
2nd byte of cipher key
3rd byte of cipher key
4th byte of cipher key
5th byte of cipher key
6th byte of cipher key
7th byte of cipher key
8th byte of cipher key
9th byte of cipher key
10th byte of cipher key
11th byte of cipher key
12th byte of cipher key
13th byte of cipher key
7-0 AesKey(127:120)
7-0 AesKey(119:112)
7-0 AesKey(111:104)
7-0 AesKey(103:96)
7-0 AesKey(95:88)
7-0 AesKey(87:80)
7-0 AesKey(79:72)
7-0 AesKey(71:64)
7-0 AesKey(63:56)
7-0 AesKey(55:48)
7-0 AesKey(47:40)
7-0 AesKey(39:32)
7-0 AesKey(31:24)
w
w
w
w
w
w
w
w
w
w
w
w
w
0x00
0x00
0x00
0x00
0x00
0x00
0x00
0x00
0x00
0x00
0x00
0x00
0x00
RegAesKey1
(0x3E)
RegAesKey2
(0x3F)
RegAesKey3
(0x40)
RegAesKey4
(0x41)
RegAesKey5
(0x42)
RegAesKey6
(0x43)
RegAesKey7
(0x44)
RegAesKey8
(0x45)
RegAesKey9
(0x46)
RegAesKey10
(0x47)
RegAesKey11
(0x48)
RegAesKey12
(0x49)
RegAesKey13
(0x4A)
Page 73
Tel: +86-755-82973805 Fax: +86-755-82973550 E-mail: sales@hoperf.com http://www.hoperf.com
RFM69HW
ADVANCED COMMUNICATIONS & SENSING
DATASHEET
14th byte of cipher key
15th byte of cipher key
7-0 AesKey(23:16)
7-0 AesKey(15:8)
7-0 AesKey(7:0)
w
w
w
0x00
0x00
0x00
RegAesKey14
(0x4B)
RegAesKey15
(0x4C)
16th byte of cipher key (LSB byte)
RegAesKey16
(0x4D)
6.7. Temperature Sensor Registers
Table 29 Temperature Sensor Registers
Name
Default
Value
Bits Variable Name
(Address)
Mode
Description
7-4
3
-
r
0000 unused
RegTemp1
(0x4E)
TempMeasStart
w
0
Triggers the temperature measurement when set. Always
reads 0.
2
TempMeasRunning
r
0
Set to 1 while the temperature measurement is running.
Toggles back to 0 when the measurement has completed.
The receiver can not be used while measuring
temperature
1-0
-
r
r
01
-
unused
7-0 TempValue
Measured temperature
-1°C per Lsb
RegTemp2
(0x4F)
Needs calibration for accuracy
6.8. Test Registers
Table 30 Test Registers
Name
Default
Value
Bits Variable Name
Mode
Description
(Address)
RegTestLna
(0x58)
7-0 SensitivityBoost
rw
0x1B High sensitivity or normal sensitivity mode:
0x1B → Normal mode
0x2D → High sensitivity mode
RegTestPa1
(0x5A)
7-0 Pa20dBm1
rw
rw
rw
rw
0x55 Set to 0x5D for +20 dBm operation on PA_BOOST.
0x55 → Normal mode and Rx mode
0x5D → +20 dBm mode
Revert to 0x55 when receiving or using PA0
RegTestPa2
(0x5C)
7-0 Pa20dBm2
0x70 Set to 0x7C for +20 dBm operation on PA_BOOST
0x70 → Normal mode and Rx mode
0x7C → +20 dBm mode
Revert to 0x70 when receiving or using PA0
RegTestDagc
(0x6F)
7-0 ContinuousDagc
7-0 LowBetaAfcOffset
0x30 Fading Margin Improvement, refer to 3.4.4
*
0x00 → Normal mode
0x20 → Improved margin, use if AfcLowBetaOn=1
0x30 → Improved margin, use if AfcLowBetaOn=0
RegTestAfc
(0x71)
0x00 AFC offset set for low modulation index systems, used if
AfcLowBetaOn=1.
Offset = LowBetaAfcOffset x 488 Hz
Page 74
Tel: +86-755-82973805 Fax: +86-755-82973550 E-mail: sales@hoperf.com http://www.hoperf.com
RFM69HW
ADVANCED COMMUNICATIONS & SENSING
DATASHEET
7. Application Information
7.1. Crystal Resonator Specification
Table 31 shows the crystal resonator specification for the crystal reference oscillator circuit of the RFM69HW.
This specification covers the full range of operation of the RFM69HW and is employed in the reference design.
Table 31 Crystal Specification
Symbol Description
Conditions
Min
Typ
Max
Unit
FXOSC
RS
XTAL Frequency
26
-
-
32
140
7
MHz
ohms
pF
XTAL Serial Resistance
XTAL Shunt Capacitance
External Foot Capacitance
30
2.8
16
C0
-
CLOAD
On each pin XTA and XTB
8
22
pF
Notes - the initial frequency tolerance, temperature stability and ageing performance should be chosen in accordance
with the target operating temperature range and the receiver bandwidth selected.
- the loading capacitance should be applied externally, and adapted to the actual Cload specification of the XTAL.
- A minimum XTAL frequency of 28 MHz is required to cover the 863-870 MHz band, 29 MHz for the 902-928 MHz
band
7.2. Reset of the Module
A power-on reset of the RFM69HW is triggered at power up. Additionally, a manual reset can be issued by controlling pin
RESET.
7.2.1. POR
If the application requires the disconnection of VDD from the RFM69HW, despite of the extremely low Sleep Mode
current, the user should wait for 10 ms from of the end of the POR cycle before commencing communications over the SPI
bus. Pin
6 (Reset) should be left floating during the POR sequence.
VDD
Pin Reset
Undefined
(output)
Wait
for
Module is ready
10 ms
from this point on
Figure 39. POR Timing Diagram
Please note that any CLKOUT activity can also be used to detect that the module is ready.
Page 75
Tel: +86-755-82973805 Fax: +86-755-82973550 E-mail: sales@hoperf.com http://www.hoperf.com
RFM69HW
ADVANCED COMMUNICATIONS & SENSING
DATASHEET
7.2.2. Manual Reset
A manual reset of the RFM69HW is possible even for applications in which VDD cannot be physically disconnected. Pin
RESET should be pulled high for a hundred microseconds, and then released. The user should then wait for 5 ms before
using the module.
Figure 40. Manual Reset Timing Diagram
Note whilst pin RESET is driven high, an over current consumption of up to ten milliamps can be seen on VDD.
Page 76
Tel: +86-755-82973805 Fax: +86-755-82973550 E-mail: sales@hoperf.com http://www.hoperf.com
RFM69HW
7.3. Reference Design
Please contact your representative for evaluation tools, reference designs and design assistance. Note that all
schematics shown in this section are full schematics, listing ALL required components, including decoupling capacitors.
Figure 41:+20dBm Schematic
A
ADVANCED COMMUNICATIONS & SENSING
DATASHEET
Page 77
Tel: +86-755-82973805 Fax: +86-755-82973550 E-mail: sales@hoperf.com http://www.hoperf.com
RFM69HW
8. Packaging Information
8.1. Package Outline Drawing
Figure 42. S 2 Package Outline Drawing
Page 78
Tel: +86-755-82973805 Fax: +86-755-82973550 E-mail: sales@hoperf.com http://www.hoperf.com
RFM69HW
A
9. Ordering Information
RFM69HW —433 S2
D
Package
Operation Band
Mode Type
P/N: RFM69HW-315S2
RFM69HW module at 315MHz band, SMD Package
P/N: RFM69HW-433S2
RFM69HW module at 433MHz band, SMD Package
P/N: RFM69HW-868S2
RFM69HW module at 868MHz band, SMD Package
P/N: RFM69HW-915S2
RFM69HW module at 915MHz band, SMD Package
V
This document may contain preliminary information and is subject to
change by Hope Microelectronics without notice. Hope Microelectronics
assumes no responsibility or liability for any use of the information
contained herein. Nothing in this document shall operate as an express or
implied license or indemnity under the intellectual property rights of Hope
Microelectronics or third parties. The products described in this document
are not intended for use in implantation or other direct life support
applications where malfunction may result in the direct physical harm or
injury to persons. NO WARRANTIES OF ANY KIND, INCLUDING, BUT
NOT LIMITED TO, THE IMPLIED WARRANTIES OF MECHANTABILITY
OR FITNESS FOR A ARTICULAR PURPOSE, ARE OFFERED IN THIS
DOCUMENT.
HOPE MICROELECTRONICS CO.,LTD
Add: 2/F, Building 3, Pingshan Private
Enterprise Science and Technology
Park, Lishan Road, XiLi Town,
Nanshan District, Shenzhen,
Guangdong, China
Tel: 86-755-82973805
Fax: 86-755-82973550
Email: sales@hoperf.com
Website: http://www.hoperf.com
http://www.hoperf.cn
©2006, HOPE MICROELECTRONICS CO.,LTD. All rights reserved.
Page 79
Tel: +86-755-82973805 Fax: +86-755-82973550 E-mail: sales@hoperf.com http://www.hoperf.com
相关型号:
©2020 ICPDF网 联系我们和版权申明