SS411P [HONEYWELL]
Bipolar Hall-Effect Digital Position Sensors with Built-in Pull-up Resistor; 双极型霍尔效应数字式位置传感器,内置上拉电阻![SS411P](http://pdffile.icpdf.com/pdf1/p00129/img/icpdf/SS411_712718_icpdf.jpg)
型号: | SS411P |
厂家: | ![]() |
描述: | Bipolar Hall-Effect Digital Position Sensors with Built-in Pull-up Resistor |
文件: | 总4页 (文件大小:198K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
![](http://public.icpdf.com/style/img/ads.jpg)
SS311PT/SS411P
Bipolar Hall-effect Digital
Position Sensors with Built-in
Pull-up Resistor
DESCRIPTION
The 2.7 Vdc to 7 Vdc supply voltage range allows this device
to be used in low voltage applications. The S311PT’s very
small size requires less PCB (printed circuit board) space,
allowing it to be used in smaller assemblies.
The SS311PT/SS411P sensors are small, versatile digital Hall-
effect devices that are operated by the magnetic field from a
permanent magnet or an electromagnet, designed to respond
to alternating North and South poles.
These sensors are available in two package styles: the
SS311PT in the subminiature SOT-23 surface mount package
and the SS411P in the leaded, flat TO-92-style package.
These bipolar sensors have enhanced sensitivity which allows
for the use of smaller, often less expensive magnets. The
internal pull-up resistor often eliminates the need for external
components, further helping to reduce system cost. These
economical bipolar sensors are suited for many simple, high-
volume, cost-sensitive, rotary sensing applications.
The SS311PT is available on tape and reel (3000 units per
reel); the SS411P is available in a bulk package (1000 units
per bag).
FEATURES
POTENTIAL APPLICATIONS
Transportation:
•
Subminiature, SOT-23 surface mount package (SS311PT)
supplied on tape and reel allows for a compact design with
automated component placement, helping to reduce
manufacturing costs
Small, leaded, flat TO-92 package (SS411P) often allows
for more space on the PCB
Sensitive, bipolar magnetics respond to alternating North
and South poles, making these products suited for speed
sensing and RPM measurement
Built-in pull-up resistor can easily interface with common
electronic circuits without adding external components,
helping to reduce total system cost
•
•
•
•
Speed and RPM (revolutions per minute) sensing
Tachometer, counter pickup
Motor and fan control
Brushless dc motor control
•
•
Industrial and Commercial:
•
•
•
•
•
•
Speed and RPM (revolutions per minute) sensing
Tachometer, counter pickup
Flow-rate sensing
Brushless dc (direct current) motor commutation
Motor and fan control
•
•
Robotics control
RoHS-compliant materials meet Directive 002/95/EC
SS311PT/SS411P
Table 1. SS311PT/SS411P Specifications (At 2.7 Vdc to 7 Vdc supply, 4 mA load, TA = -40 ºC to 150 ºC [-40 ºF to 302 ºF]
Characteristic
Supply voltage
Supply current
Condition
-40 °C to 150 °C [-40 °F to 302 °F]
gauss <-140, Vs = 5 V, 25 °C [77°F]
-40 °C to 150 °C [-40 °F to 302 °F]
–
Minimum
Typical
Maximum
Unit
Vdc
2.7
–
–
–
–
–
–
–
5.0
5.5
–
–
–
–
–
–
7.0
–
mA
14
4.0
0.4
10
1.5
1.5
Output current
Vsat
mA
V
µA
gauss >140
gauss <-140
Output leakage current
Output rise time
Output fall time
Thermal resistance:
SS311PT
SS411P
Operate
Release
Differential
25 °C [77 °F]
µs
°C/W
–
–
–
–
-30
303
233
55
-55
–
–
–
140
30
–
-40 °C to 150 °C [-40 °F to 302 °F]
-40 °C to 150 °C [-40 °F to 302 °F]
-40 °C to 150 °C [-40 °F to 302 °F]
gauss
gauss
gauss
°C [°F]
°C [°F]
-140
40
-40 [-40]
-40 [-40]
Operating temperature
Storage temperature
–
–
–
–
150 [302]
150 [302]
NOTICE
Bipolar Hall-effect sensors may have an initial output in either the ON or OFF state if powered up with an applied magnetic field in
the differential zone (applied magnetic field >Brp and <Bop). Honeywell recommends allowing 10 µs for output voltage to stabilize
after supply voltage has reached 5 Vdc.
Table 2. SS311PT/SS411P Absolute Maximum Ratings1
Characteristic
Supply voltage
Applied output voltage
Output current
Minimum
Typical
Maximum
7.0
7.0
8.0
no limit
Unit
Vdc
Vdc
mA
gauss
-0.5
-0.5
–
–
–
–
–
Magnetic flux
–
Note 1: The magnetic field strength (gauss) required to cause the switch to change state (operate and release) will be as specified
in the magnetic characteristics. To test the switch against the specified magnetic characteristics, the switch must be placed in a
uniform magnetic field.
NOTICE
Absolute maximum ratings are the extreme limits that the device will withstand without
damage to the device. However, the electrical and mechanical characteristics are not
guaranteed as the maximum limits (above recommended operating conditions) are
approached, nor will the device necessarily operate at absolute maximum ratings.
Figure 1. Current Sinking Output Block Diagram
2
www.honeywell.com/sensing
Bipolar Hall-Effect Digital Position Sensors
Figure 2. SS311PT Mounting/Tape and Reel Dimensions (For reference only. mm/[in])
Figure 3. SS411P Mounting Dimensions (For reference only. mm/[in])
Honeywell Sensing and Control
3
Order Guide
Catalog Listing
SS311PT
Description
Bipolar Hall-effect digital position sensor with built-in pull-up resistor, SOT-23 package, tape and reel
packaging (3000 units per reel)
SS411P
Bipolar Hall-effect digital position sensor with built-in pull-up resistor, flat TO-92 package, bulk packaging
(1000 units per bag)
WARNING
PERSONAL INJURY
WARNING
MISUSE OF DOCUMENTATION
DO NOT USE these products as safety or emergency stop
devices or in any other application where failure of the
product could result in personal injury.
•
The information presented in this product sheet is for
reference only. Do not use this document as a product
installation guide.
Failure to comply with these instructions could result
in death or serious injury.
•
Complete installation, operation, and maintenance
information is provided in the instructions supplied with
each product.
Failure to comply with these instructions could result
in death or serious injury.
SALES AND SERVICE
Honeywell serves its customers through a worldwide network
of sales offices, representatives and distributors. For
application assistance, current specifications, pricing or name
of the nearest Authorized Distributor, contact your local sales
office or:
WARRANTY/REMEDY
Honeywell warrants goods of its manufacture as being free of
defective materials and faulty workmanship. Honeywell’s
standard product warranty applies unless agreed to otherwise
by Honeywell in writing; please refer to your order
acknowledgement or consult your local sales office for specific
warranty details. If warranted goods are returned to Honeywell
during the period of coverage, Honeywell will repair or replace,
at its option, without charge those items it finds defective. The
foregoing is buyer’s sole remedy and is in lieu of all other
warranties, expressed or implied, including those of
merchantability and fitness for a particular purpose. In no
event shall Honeywell be liable for consequential, special,
or indirect damages.
E-mail: info.sc@honeywell.com
Internet: www.honeywell.com/sensing
Phone and Fax:
Asia Pacific
+65 6355-2828
+65 6445-3033 Fax
+44 (0) 1698 481481
+44 (0) 1698 481676 Fax
+1-305-805-8188
+1-305-883-8257 Fax
+1-800-537-6945
Europe
Latin America
USA/Canada
While we provide application assistance personally, through
our literature and the Honeywell web site, it is up to the
customer to determine the suitability of the product in the
application.
+1-815-235-6847
+1-815-235-6545 Fax
Specifications may change without notice. The information we
supply is believed to be accurate and reliable as of this
printing. However, we assume no responsibility for its use.
Sensing and Control
Honeywell
1985 Douglas Drive North
005914-1-EN IL50 GLO Printed in USA
October 2009
© 2009 Honeywell International Inc. All rights reserved.
Golden Valley, MN 55422
www.honeywell.com/sensing
相关型号:
©2020 ICPDF网 联系我们和版权申明