HRF-SW1021 [HONEYWELL]
SP4T Absorptive RF Switch DC To 2.5 GHz Operation;型号: | HRF-SW1021 |
厂家: | Honeywell |
描述: | SP4T Absorptive RF Switch DC To 2.5 GHz Operation |
文件: | 总5页 (文件大小:138K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
HRF-SW1021
SP4T Absorptive RF Switch DC To 2.5 GHz Operation
The Honeywell HRF-SW1021 is a high performance single pole four throw (SP4T)
absorptive RF switch that is ideal for use in wireless basestation and handset
applications that require minimum power and minimum insertion loss.
The HRF-SW1021 is manufactured with Honeywell's patented Silicon On Insulator
(SOI) CMOS technology, which provides the performance of GaAs with the economy
and integration capabilities of conventional CMOS technology. These switches are
DC coupled to improve lower operating frequency, frequency response and reduce
the number of DC bias points required.
FEATURES
HRF-SW1021 in VQFN Package
•
•
•
•
•
•
•
Typical High Isolation Of > 42 dB @ 2 GHz
Typical Low Insertion Loss Of 1.2dB @ 2 GHz
Integrated CMOS Control Logic
DC-coupled, bi-directional RF Path
Single Positive Supply Voltage
Ultra Small VQFN Packaging
Impedance matched to 75 Ohm systems
RF ELECTRICAL SPECIFICATIONS @ + 25oC
Results @ VDD = 5.0 +/- 10%, VSS = 0 unless otherwise stated, Z0 = 75 Ohms
Contact Honeywell for relative performance at other supply configurations
Parameter
Test Condition
Frequency
Minimum
Typical
Maximum
Units
1.0 GHz
2.0 GHz
2.5 GHz
1.1
1.2
1.3
1.7
2.0
2.1
dB
dB
dB
Insertion Loss
1.0 GHz
2.0 GHz
2.5 GHz
45
33
30
54
42
40
dB
dB
dB
Isolation
dB
Return Loss
Input P1dB
-15
-20
V
V
SS = Gnd
SS = -5V
1.0 GHz
1.0 GHz
15
25
dBm
dBm
Two-Tone Inputs, up to + 5 dBm
VSS = Gnd
Input IP3
2.0 GHz
2.0 GHz
33
34
dBm
dBm
VSS = -5V
Trise, Tfall
Ton, Toff
10% To 90%
50% Cntl To 90% / 10% RF
10
20
ns
ns
HRF-SW1021
DC ELECTRICAL SPECIFICATIONS @ + 25°C
Parameter
Minimum
3.31
Typical
5.0
Maximum
Units
V
VDD
VSS
IDD
5.5
-5.0
V
<5
35
0.8
VDD
10
uA
V
CMOS Logic Level (0)
CMOS Logic Level (1)
Input Leakage Current
0
VDD – 0.8
V
uA
Note 1 - Performance curves are for VDD = +5.0 +/- 10%
ABSOLUTE MAXIMUM RATINGS1
Parameter
Absolute Maximum
Units
VDD
+6.0
-5.5
V
V
VSS
Vin Digital Logic 0
Vin Digital Logic 1
Input Power
ESD Voltage2
-0.6
V
Vdd + 0.6
> 35
V
dBm
V
400
Moisture Sensitivity Level
Operating Temperature Range
Storage Temperature Range
Level 1
-40 to +85
-65 to +125
oC
oC
Note 1 - Operation of this device beyond any of these parameters may cause permanent damage.
Note 2 - Although the HRF-SW1021 contains ESD protection circuitry on all digital inputs, precautions should be taken to
ensure that the Absolute Maximum Ratings are not exceeded.
Latch-Up: Unlike conventional CMOS digital attenuators, Honeywell’s HRF-SW1021 is immune to latch-up.
TRUTH TABLE
C1
C0
RF Output 1
RF Output 2
RF Output 3
RF Output 4
0
0
1
1
0
1
0
1
RFINPUT
RFINPUT
RFINPUT
RFINPUT
"0" = CMOS Low, "1” = CMOS High
PIN CONFIGURATIONS
Pin
Function
Pin
Function
Pin
Function
Pin
Function
1
2
3
4
5
GROUND
RFOUTPUT4
GROUND
VDD
6
7
8
9
10
RFOUTPUT3
GROUND
GROUND
GROUND
RFOUTPUT2
11
12
13
14
15
C1
C0
16
17
18
19
20
GROUND
GROUND
RFINPUT
GROUND
VSS
GROUND
RFOUTPUT1
GROUND
GROUND
Note: Bottom ground plate must be grounded for proper RF performance.
2
www.honeywell.com/microwave
HRF-SW1021
PERFORMANCE CURVES
Insertion Loss
Typical SW1021 Insertion Loss
0.0
-0.5
-1.0
-1.5
-2.0
-2.5
-3.0
-3.5
-4.0
0
0.5
1
1.5
2
2.5
Frequency (GHz)
Isolation
Typical SW1021 Isolation
-20
-30
-40
-50
-60
-70
-80
0.0
0.5
1.0
1.5
2.0
2.5
Frequency (GHz)
www.honeywell.com/microwave
3
HRF-SW1021
PACKAGE OUTLINE DRAWING
Notes
1. Pin 1 identifier can be a combination or a dot and/or chamfer.
2. Dimensions are in millimeters.
LEAD FINISH
The package leads are Tin Lead (SnPb).
CIRCUIT APPLICATION INFORMATION
These attenuators require a DC reference to ground. They may not operate properly when AC coupled on both the RF
input and output without a DC ground reference provided as part of the circuit. See Application Note AN311 at
www.honeywell.com/microwave.
4
www.honeywell.com/microwave
HRF-SW1021
EVALUATION CIRCUIT BOARD
Honeywell's evaluation board provides an easy to use method of evaluating the RF performance of our switch. Simply
connect power; DC and RF signals to be measuring switch performance in less than 10 minutes.
Gnd
C1
C0
RF Input
VSS
VDD
Gnd
HRF-SW1020-A
HRF-SW1021
Evaluation Board
Top View
RF Out4
RF Out1
HRF-SW1021 Evaluation Board
RF Out3
RF Out2
Note:
HRF-SW1021 is the Z0 = 75 ohm version of the SW1020 evaluation board.
EVALUATION CIRCUIT BOARD LAYOUT DESIGN DETAILS
Item
Description
PCB
Impedance Matched Multi-Layer FR4
Switch
HRF-SW1021 RF Switch
Chip Capacitor
RF Connector
DC Pin
Panasonic Model ECU-E1C103KBQ Capacitor, .01uf 0402 10% 16V
Johnson Connectors Model 142-0701-801 SMA RF Coaxial Connector
Mil-Max Model 800-10-064-10-001 Header Pins
ORDERING INFORMATION
Ordering Number
Delivery Method
Units Per Shipment
3000 Units per Reel
<3000
One Board Per Box
HRF-SW1021-TR
HRF-SW1021-T
HRF-SW1021-E
Delivered On Tape And Reel
Delivered on Tape
Engineering Evaluation Board
FIND OUT MORE
For more information on Honeywell’s Microwave Products visit us online at www.honeywell.com/microwave or contact
us at 800-323-8295 (763-954-2474 internationally).
Honeywell reserves the right to make changes to improve reliability, function or design. Honeywell does not assume any liability arising out of the
application or use of any product or circuit described herein; neither does it convey any license under its patent rights nor the rights of others.
Honeywell
12001 Highway 55
Plymouth, MN 55441
Tel: 800-323-8295
www.honeywell.com/microwave
Form #1021W
January 2007
©2007 Honeywell International Inc.
相关型号:
HRF-SW1021-TR
SP4T, 0MHz Min, 2500MHz Max, 1 Func, 3.5dB Insertion Loss-Max, CMOS, 4 X 4 MM, ULTRA SMALL, VQFN, LPCC-20
HONEYWELL
HRF-SW1030-B
SP6T, 0MHz Min, 2500MHz Max, 1 Func, 3.8dB Insertion Loss-Max, CMOS, 4 X 4 MM, ULTRA SMALL, LPCC-24
HONEYWELL
HRF-SW1030-TR
SP6T, 0MHz Min, 2500MHz Max, 1 Func, 3.8dB Insertion Loss-Max, CMOS, 4 X 4 MM, ULTRA SMALL, VQFN, LPCC-24
HONEYWELL
©2020 ICPDF网 联系我们和版权申明