S11049_15 [HAMAMATSU]
Photo IC for optical switch;
| 型号： | S11049_15 |
| 厂家： | 
HAMAMATSU CORPORATION |
| 描述： | Photo IC for optical switch |
| 文件： | 总6页 (文件大小：473K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
Photo IC for optical switch
S11049 series
Analog output photo IC for optical switch
The S11049 series photo ICs are designed for optical switches and provides an analog waveform output proportional to the
intensity of incident pulsed light.
Features
Applications
Large allowable background light level: 4000 lx Min.
High linearity
Optical switch
Optical receivers in various sensor devices
Low noise: 1.8 mV rms Max.
Absolute maximum ratings (Ta=25 °C)
Parameter
Symbol
Vcc
S11049-202SB
250
S11049-203DT
-0.5 to +7
300
-0.5 to +7
-25 to +85
-30 to +85
Unit
V
mW
V
°C
°C
Supply voltage
Power dissipation*1
Output voltage
P
Vout
Topr
Tstg
Operating temperature*2
Storage temperature*2
-40 to +100
*1: Power dissipation decreases at a rate of 3.3 mW/°C on the S11049-202SB and 4 mW/°C on the S11049-203DT at Ta=25 °C and
above.
*2: No condensation
Note: Exceeding the absolute maximum ratings even momentarily may cause a drop in product quality. Always be sure to use the
product within the absolute maximum ratings.
1
www.hamamatsu.com
Photo IC for optical switch
S11049 series
Electrical and optical characteristics (Ta=25 °C, Vcc=5.0 V)
Parameter
Supply voltage
Current consumption
Spectral response range
Peak sensitivity wavelength
Symbol
Vcc
Icc
λ
λp
Condition
Min.
4.5
-
-
-
Typ.
-
-
Max.
5.5
2.2
-
Unit
V
mA
nm
nm
380 to 1120
760
-
λ=950 nm*3
Input signal=100 kHz
Photo sensitivity
A
120
200
300
V/mW
Including diffused reflection
inside package
Input pulse signal 0.01 μW to 4.0 μW*3
Input pulse signal 4.0 μW to 7.5 μW*3
-10
-50
-
1250
4000
-
-
-
-
+10
+50
50
1650
-
AC photoelectric sensitivity linearity
Alin
%
Low band
Cut-off frequency*4
fcl
fch
Pdc
VON
3
*
kHz
High band
1450
6000
-
Allowable background light level*5
Output noise voltage (with no input)
Input pulse signal 2.5 μW*3
lx
3
*
2.8
mV rms
*3: Measurement circuit (Waveform at terminal Vo is measured.)
*4: Cutoff frequency definition
Vcc
0.1 μF
5 V
0.01 μF
Out
Vo
5.1 kΩ
3.3 kΩ
GND
KPICC0161EB
fcl
fch
Frequency (logarithmic axis)
KPICC0241EA
*5: This is defined as the background light level in the active area at witch the photo IC sensitivity drops by 20%
Spectral response (typical example)
Block diagram
(Ta=25 °C)
100
Vcc
80
OUT
GND
Preamp
Buffer
60
Photodiode
40
KPICC0162EB
20
0
300 400 500 600 700 800 900 1000 1100 1200
Wavelength (nm)
KPICB0142EB
2
Photo IC for optical switch
S11049 series
Dimensional outlines (unit: mm)
S11049-202SB
10°
5°
5.2 0.2
(Including burr)
5.0
Photosensitive area
2.0
1.0
1.1 × 0.8
2.5 0.2
ϕ1.2
Depth 0.15 max.
0.45
0.25+-00.1.15
1.27 1.27 1.27
(Specified at the lead root)
Tolerance unless otherwise noted: 0.1ꢀ 2°
Shaded area indicates burr.
GND
Vout
Vcc
Values in parentheses are not guaranteedꢀ
but for reference.
GND
Lead surface finish: silver plating
Packing: polyethylene pack [anti-static type]
(200 pcs/pack)
KPICA0083EA
3
Photo IC for optical switch
S11049 series
S11049-203DT
Photosensitive
area
Photosensitive
surface
3.2 0.2
(Including burr)
1.1
0.05
0.45
0.75
1.0 0.4
3.0*
1.0 0.4
5.0 0.3
3.0*
0.45 0.3
0.45 0.3
1.3
Photosensitive
surface
2.8
2.4
Mirror surface area
(GND)
(GND)
GND
Connect the (GND) terminal to
the
GND terminal on the
circuit board.
(GND)
Vo
Tolerance unless otherwise noted:
0.1ꢀ 2°
Vo
(GND)
Vcc
Shaded area indicates burr.
Chip position accuracy with
respect to package dimensions
marked *
2.9
(GND)
(GND)
3.0*
Xꢀ Y≤ 0.2ꢀ ꢁ≤ 2°
KPICA0092EA
4
Photo IC for optical switch
S11049 series
Standard packing specifications (S11049-203DT)
Reel (conforms to JEITA ET-7200)
Dimensions
254 mm
Hub diameter
100 mm
Tape width
12 mm
Material
PS
Electrostatic characteristics
Antistatic treatment
Embossed tape (unit: mm, material: PS, electrically conductive)
8.0 0.1
2.0 0.1
4.0 0.1
ϕ1.5 0.1
0.3 0.1
2.3 0.2
5.4 0.2
Reel feed direction
KPICC0238EB
Packing quantity
2000 pcs/reel
Packing type
Reel and desiccant in moisture-proof packaging (vacuum-sealed)
5
Photo IC for optical switch
S11049 series
Measured example of temperature profile with our hot-air reflow oven for product testing (S11049-203DT)
300 °C
240 °C max.
220 °C
190 °C
170 °C
Preheating
70 to 90 s
Actual heating
40 s max.
Time
KPICB0171EA
∙ These products support lead-free soldering. After unpacking, store them in an environment at a temperature of 30 °C or less and a
humidity of 60% or less, and perform soldering within 24 hours.
· The effect that the product receives during reflow soldering varies depending on the circuit board and reflow oven that are used.
When setting the reflow soldering conditions, check for any problems by testing out the reflow soldering methods in advance.
Related information
www.hamamatsu.com/sp/ssd/doc_en.html
Precautions
∙ Notice
· Metal, ceramic, plastic package products
· Surface mount type products
Information described in this material is current as of August, 2014.
Product specifications are subject to change without prior notice due to improvements or other reasons. This document has been carefully prepared and the
information contained is believed to be accurate. In rare casesꢀ howeverꢀ there may be inaccuracies such as text errors. Before using these productsꢀ always
contact us for the delivery specification sheet to check the latest specifications.
The product warranty is valid for one year after delivery and is limited to product repair or replacement for defects discovered and reported to us within that
one year period. Howeverꢀ even if within the warranty period we accept absolutely no liability for any loss caused by natural disasters or improper product
use.
Copying or reprinting the contents described in this material in whole or in part is prohibited without our prior permission.
www.hamamatsu.com
HAMAMATSU PHOTONICS K.K.ꢀ Solid State Division
1126-1 Ichino-choꢀ Higashi-kuꢀ Hamamatsu Cityꢀ 435-8558 Japanꢀ Telephone: (81) 53-434-3311ꢀ Fax: (81) 53-434-5184
U.S.A.: Hamamatsu Corporation: 360 Foothill Roadꢀ Bridgewaterꢀ N.J. 08807ꢀ U.S.A.ꢀ Telephone: (1) 908-231-0960ꢀ Fax: (1) 908-231-1218
Germany: Hamamatsu Photonics Deutschland GmbH: Arzbergerstr. 10ꢀ D-82211 Herrsching am Ammerseeꢀ Germanyꢀ Telephone: (49) 8152-375-0ꢀ Fax: (49) 8152-265-8
France: Hamamatsu Photonics France S.A.R.L.: 19ꢀ Rue du Saule Trapuꢀ Parc du Moulin de Massyꢀ 91882 Massy Cedexꢀ Franceꢀ Telephone: 33-(1) 69 53 71 00ꢀ Fax: 33-(1) 69 53 71 10
United Kingdom: Hamamatsu Photonics UK Limited: 2 Howard Courtꢀ 10 Tewin Roadꢀ Welwyn Garden Cityꢀ Hertfordshire AL7 1BWꢀ United Kingdomꢀ Telephone: (44) 1707-294888ꢀ Fax: (44) 1707-325777
North Europe: Hamamatsu Photonics Norden AB: Torshamnsgatan 35 16440 Kistaꢀ Swedenꢀ Telephone: (46) 8-509-031-00ꢀ Fax: (46) 8-509-031-01
Italy: Hamamatsu Photonics Italia S.r.l.: Strada della Moiaꢀ 1 int. 6ꢀ 20020 Arese (Milano)ꢀ Italyꢀ Telephone: (39) 02-93581733ꢀ Fax: (39) 02-93581741
China: Hamamatsu Photonics (China) Co.ꢀ Ltd.: B1201ꢀ Jiaming Centerꢀ No.27 Dongsanhuan Beiluꢀ Chaoyang Districtꢀ Beijing 100020ꢀ Chinaꢀ Telephone: (86) 10-6586-6006ꢀ Fax: (86) 10-6586-2866
6
Cat. No. KPIC1087E01 Aug. 2014 DN
相关型号：
S11071-1004
CCD Sensor, 1024 Horiz pixels, 16 Vert pixels, Rectangular, Through Hole Mount, DIP-24
HAMAMATSU
S11071-1104
CCD Sensor, 2048 Horiz pixels, 16 Vert pixels, Rectangular, Through Hole Mount, DIP-24
HAMAMATSU
S11071-1106
CCD Sensor, 2048 Horiz pixels, 64 Vert pixels, Rectangular, Through Hole Mount, DIP-24
HAMAMATSU
S1109A-FREQ1-OUT3
TTL Output Clock Oscillator, 20MHz Min, 30MHz Max, HALF SIZE, RESISTANCE WELDED, METAL, DIP-4
PERICOM
S1109A-FREQ2-OUT3
TTL Output Clock Oscillator, 30MHz Min, 70MHz Max, HALF SIZE, RESISTANCE WELDED, METAL, DIP-4
PERICOM
S1109A-FREQ3-OUT3
TTL Output Clock Oscillator, 70MHz Min, 80MHz Max, FULL SIZE, RESISTANCE WELDED, METAL, DIP-4
PERICOM
©2020 ICPDF网 联系我们和版权申明