L11354-01_15 [HAMAMATSU]
Photo IC for optical link;
| 型号： | L11354-01_15 |
| 厂家： | 
HAMAMATSU CORPORATION |
| 描述： | Photo IC for optical link |
| 文件： | 总12页 (文件大小：683K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
Photo IC for optical link
L11354-01
S11355-03
P11379-04AT
Transmitter Receiver
photo IC photo IC
L11354-01 S11355-03
Transmitter/
receiver photo IC
P11379-04AT
For 150 Mbps optical link
This photo IC is capable of data communication at a data rate of 150 Mbps through a plastic optical fiber (POF). Its
transmitter is composed of a 650 nm RC (resonant cavity) type LED, which is suitable for POF communications, and a driver
circuit that supports an LVDS interface.
The transmitter has a built-in temperature compensation function that adjusts for the reduction in the light emission power
caused by the high temperature emitted from the RC type LED. This function makes light emission with stable power
possible over a wide temperature range. The receiver is composed of a PIN photodiode and signal processing circuit. The
adoption of a full differential structure using a dummy photodiode eliminates the effects of external noise, achieving high
sensitivity. In addition, the photo IC has a sleep function that suppresses power consumption by switching to standby mode
when there is no input.
This product features high quality and high reliability, allowing it to be installed even in automobiles for in-vehicle
networking. It is already used as an optical fiber transceiver (FOT) for a MOST network, which is a type of in-vehicle
multimedia network. POFs with ferrule are also available.
Features
Applications
Communication speed up to 150 Mbps
Sidelooker type and SMD type are available.
3.3 V power supply operation
Data transmission in harsh, noisy environments, such
as in FA and OA.
High-speed, short-distance data transmissio
Only for vehicle networks (MOST)
Wide operating temperature: -40 to +95 °C
Suitable for reflow soldering
MOST compliant products
Sleep mode function
Specifications of these products are subject to
change without prior notice to keep up with
changes in the MOST standard.
Absolute maximum ratings
Parameter
L11354-01
P11379-04AT
(Transmitter)
S11355-03
Symbol
Vcc_TX
Condition
Value
Unit
V
-0.5 to +7.0
Supply
voltage
Ta=-40 to +95 °C
P11379-04AT
(Receiver)
Vcc_RX
-0.5 to +4.6
Input voltage
Vi
P
Ta=-40 to +95 °C
Ta=-40 to +95 °C
-0.5 to Vcc+0.5
V
L11354-01
S11355-03
P11379-04AT
350
320
1250
-40 to +95
-40 to +110
Power
dissipation
mW
Operating temperature
Storage temperature
Reflow soldering conditions*1
Topr
Tstg
Tsol
°C
°C
-
Peak temperature 260 °C max., 3 times (see page 12)
*1: JEDEC level 2a
Note: Exceeding the absolute maximum ratings even momentarily may cause a drop in product quality. Always be sure to use the
product within the absolute maximum ratings.
Recommended operating conditions
Parameter
Supply voltage
Data rate
Symbol
Vcc
fD
Condition
Min.
3.135
-
Typ.
3.3
-
Max.
3.465
150
Unit
V
Mbps
DCA coding
1
www.hamamatsu.com
Photo IC for optical link
L11354-01, S11355-03, P11379-04AT
L11354-01, P11379-04AT (Transmitter)
Electrical and optical characterisitics*2 (Ta=-40 to +95 °C, Vcc=3.135 to 3.465, unless otherwise noted*3)
Parameter
Current consumption
Peak emission wavelength
Spectral width (RMS)
Fiber coupled optical output 1
Fiber coupled optical output 2
Extinction ratio
Rise time
Fall time
Transfer jitter (RMS)
Overshoot
Undershoot
Symbol
Icc
λC2
σλ2
Po1
POFF2
re
tr
tf
Jtr2
rpos
rnos
VinRL
VinRH
VinCL
VinCH
IinRL
IinRH
IinCL
IinCH
IinTXL
IinTXH
FON1
FOFF1
tON2
tOFF2
A2 to F2
Condition
Min.
Typ.
-
650
-
-
-
-
-
Max.
40
675
17
-1.5
-50
-
0.5
0.5
112
Unit
mA
nm
nm
dBm
dBm
dB
UI
UI
ps
-
-
4
-
635
-
-7
-
10
-
-
*
CTRL_TX=Low,*5 *6
20 to 80%,*4 *5
80 to 20%,*4 *5
*4 *5
-
-
-
5
See “ Overshoot
See “ Undershoot
”
”
table.
table.
*
5
*
7
-
2
-
2
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
0.8
-
0.8
-
-0.1
50
-0.1
50
-0.1
0.1
73.743
10
100
2
*
Input voltage level “/RST”
Input voltage level “CTRL_TX”
Input current “/RST”
V
7
*
V
/RST=Low
/RST=High
CTRL_TX=Low
CTRL_TX=High
TXN, TXP=Low
TXN, TXP=High
μA
μA
μA
Input current “CTRL_TX”
Input current “TXN” “TXP”
-
During transmission
Frequency range
12
0
-
MHz
kHz
μs
μs
-
During non-transmission
*8 *9
*8 *10
Valid MOST data (SP2) time
Eye mask
-
See “ Eye mask
”
table.
*2: Electrical interface conforms to LVDS standards except common mode input voltage.
*3: Connect a bypass capacitor (0.1 ꢀF) between Vcc and GND at a position within 3 mm from the leads. Also connect a 10 ꢀF capacitor
near the photo IC.
L11354-01: The center of the optical fiber is aligned with the center of the package lens. The distance between the fiber end and
the lens top is 0.1 mm.
*4: Input signal rate 150 Mbps (DCA coding)
*5: Input signal
Parameter
Differential input voltage
Common mode input voltage
Total jitter
Symbol
Vid
VCM
tTJtp1
Jtr1
Min.
200
0.05
-
Typ.
Max.
1272
Vcctx - 1.2
0.15
Unit
mV
V
UI
ps
-
-
-
-
Transfer jitter (RMS)
-
50
*6: Average value, fiber core diameter ϕ1 mm, POF, NA=0.5, 1 m (made by Mitsubishi Rayon)
*7: /RST signal
Parameter
Valid supply voltage range
Logic switching threshold
Symbol
VVALID
VT
tD+
tD-
Min.
1
2.97
1
Max.
3.465
-
-
Unit
V
V
ms
μs
0→1
1→0
Logic delay time
0
100
Note: See “
Timing chart” for the /RST signal timing chart.
*8: See “ Timing chart”.
*9: Delay time for light output to turn on
*10: Delay time for light output to turn off
2
Photo IC for optical link
L11354-01, S11355-03, P11379-04AT
Overshoot
Parameter
Amplitude*11
-0.200
-0.200
0.500
Time (UI)
-0.630
0.100
Overshoot
AO
BO
CO
DO
EO
FO
GO
HO
JO
Keep out area
KO
JO
0.100
b1=1
0.800
0.350
EO
0.800
1.370
DO
HO
b0 + b1
2
CO
0.200
-0.630
-0.350
-0.100
-0.100
1.370
0.200
GO
FO
Keep out
area
0.500
b0=0
BO
1.400
AO
1.400
KPICB0153EA
KO
T=0
11: On the basis of b =0 and b =1
*
0
1
Undershoot
Parameter
Amplitude*12
0.800
0.800
0.850
0.850
0.800
0.800
0.500
-0.200
-0.200
1.400
1.400
1.340
1.150
1.150
0.500
0.200
0.200
Time (UI)*13
-0.630 - x
-0.530 - x
-0.530 - x
-0.430
Undershoot
AU
BU
CU
DU
EU
FU
GU
HU
JU
LU
MU
KU
NU
PU
b1=1
CU
DU
-0.430
Keep out area
FU
AU
BU EU
-0.350
-0.100
b0 + b1
RU
-0.100
GU
2
SU
1.370
TU
-0.630 - x
-0.530 - x
-0.530 - x
-0.220 - x
0.100
KU
LU
b0=0
MU
NU
PU
RU
SU
TU
JU
HU
Keep out area
0.100
T=0
0.350
KPICB0154EB
1.370
12: On the basis of b =0 and b =1
*
0
1
*13: The positions of Au, Bu, Cu, Ku, Lu and Mu on the time axis depend on the MOST data pulse width (2 to 6).
x=MOST data pulse width - 2
For 2UI: x=0, For 6UI: x=4
Eye mask
Parameter
Amplitude
Time (UI)
0.150
Eye mask
A2
B2
C2
D2
E2
F2
0.5 × (b1 + b0)
B2
C2
0.400
0.8 × (b1 - b0)+b0
0.8 × (b1 - b0)+b0
0.5 × (b1 + b0)
A2
D2
0.600
Keep out area
0.850
F2
E2
0.600
0.2 × (b1 - b0)+b0
0.2 × (b1 - b0)+b0
KPICB0155EA
0.400
3
Photo IC for optical link
L11354-01, S11355-03, P11379-04AT
S11355-03, P11379-04AT (Receiver)
Electrical and optical characterisitics*14 (Ta=-40 to +95 °C, Vcc=3.135 to 3.465, unless otherwise noted*15)
Parameter
Peak sensitivity wavelength
Current consumption (operation mode)
Current consumption (sleeping mode)
Symbol
λp
Icco
Iccs
Vmh
Vml
Condition
Min.
-
-
-
2.5
-
Typ.
800
-
-
-
-
Max.
-
40
30
-
Unit
nm
mA
μA
V
16
*
Dark state
Imh=20 μA,*17
Iml=0.2 mA,*17
High level output voltage
Low level output voltage
STATUS
0.5
V
Operation to sleeping mode transition
receivable level
16 18 19
*
*
*
-
-
-35
dBm
POFF3
Transfer jitter (RMS)
Error rate
Valid MOST data (input signal) frequency
Invalid MOST data frequency
Time from input signal start to operation mode
Time from input signal start to STATUS ON
Time from STATUS ON to LVDS output stabilization
Time from input signal stop to sleeping mode
LVDS output hold time
-
-
12
0
-
-
-
-
-
-
-
-
230
10-9
73.743
10
ps
-
MHz
kHz
ms
Jtr4
Pe
FON3
FOFF3
tON4
tSTATF
tLVDSV4
tOFF4
16 19 20 21 22
*
*
*
*
*
23
23
23
23
23
23
*
*
*
*
*
*
-
10
200
-
-
1
-
1000
100
1
-
2
s
μ
s
μ
s
m
-
-
s
tLVDSH4
tSTATR
A4 to F4
μ
Time from input signal stop to STATUS OFF
Eye mask
s
μ
See “ Eye mask
”
table.
-
*14: Electrical interface conforms to LVDS standards except differential output amplitude level
*15: Connect a bypass capacitor (0.1 ꢀF) between Vcc and GND at a position within 3 mm from the leads. Also connect a 10 ꢀF
capacitor near the photo IC.
*16: Input signal
Parameter
Optical data that allows Valid
MOST data (SP4) to be obtained P11379-04AT
Symbol
Popt3
Min.
-23.5
-21.5
-
-
Typ.
Max.
-2
-2
2
2
Unit
S11355-01
-
-
-
-
-
-
dBm
Rise time
Fall time
Total jitter
Extinction ratio
trtp3
tftp3
tTJtp3
re
ns
ns
ps
dB
-
10
600
-
*17: Changes to operation mode when input light enters the receiver section. When STATUS output is low, the photo IC is in operation
mode. When STATUS output is high, the photo IC is in sleeping mode.
*18: Input light is specified as the average power at the fiber end. The optical fiber used is a POF (NA=0.5).
*19: The center of the optical fiber is aligned with the center of the package lens. The distance between the fiber end and the lens top
is 0.1 mm.
*20: RL=100 kΩ, CL=3 pF (including parasitic capacitance such as probe, connector and circuit board)
*21: A standard transmitter specified by HAMAMATSU is used to input light.
*22: Optical input signal rate=150 Mbps (DCA coding)
*23: See “
Timing chart”.
Eye mask
Parameter
Amplitude (mV)
Time (UI)
0.275
0.425
0.575
0.725
0.575
0.425
-
Eye mask
0
A4
B4
C4
D4
E4
F4
G4
H4
G4
Keep out area
148
148
0
B4
C4
A4
D4
Keep out area
-148
-148
636
-636
F4
E4
H4
Keep out area
-
KPICB0156EA
4
Photo IC for optical link
L11354-01, S11355-03, P11379-04AT
Timing chart
L11354-01, P11379-04AT (Transmitter)
Reset: ON
Signal: ON
VCCTXOR max.
VCCTXOR max.
VCCTXOR min.
EOC power
VCCTXOR min.
EOC power
VT
VT
0 V
0 V
tD+
tD+
/RST
/RST
SP1
Disabled
Valid MOST data
b1
POFF2
Disabled
Valid MOST data
LVDS 0
SP1
b1
Valid MOST data
Valid MOST data
P
OFF2
SP2
SP2
tON2
tON2
Signal: OFF
Reset: OFF
EOC power
EOC power
0 V
VT
VT
0 V
tD-
/RST
/RST
SP1
SP2
Valid MOST data
Valid MOST data
LVDS 0
Disabled
SP1
SP2
Valid MOST data
Disabled
Valid MOST data
b0
b0
POFF2
tOFF2
POFF2
tOFF2
KPICC0176EA
KPICC0176EA
S11355-03, P11379-04AT (Receiver)
tON4
tOFF4
tSTATF
tLVDSV4
tLVDSH
tSTATR
b1
Valid MOST data
b0
SP3
PON3
POFF3
1
STATUS
SP4
0
Disabled
Enabled
Valid MOST data
LVDS 0
Disabled
KPICC0181EA
5
Photo IC for optical link
L11354-01, S11355-03, P11379-04AT
Block diagram
L11354-01, P11379-04AT (Transmitter)
VCC_TX
Current driver
TXP
TXN
RC type
LED
LVDS
receiver
Peak current driver
Signal detection
/RST
Temperature
monitor
Current source
Ctrl_TX
GND_TX
KPICC0177EB
S11355-03, P11379-04AT (Receiver)
VCC_RX
VCC_RX2
PD
GND_RX
RXP
RXN
Compa-
rator
Main
LVDS-
OUT
Preamp
amplifier
Sleep
level
comparator
SD
judge
Bias
STATUS
KPICC0178EA
6
Photo IC for optical link
L11354-01, S11355-03, P11379-04AT
Connection example
L11354-01
3.3 V
L1
+
+
C1 C2
C3
VCC_TX
GND_TX
Ctrl_TX
Ctrl_TX
TXP
TXP
L11354-01
R1
TXN
/RST
TXN
/RST
GND
*Bold line: 50 Ω impedance matching
KPICC0179EA
Symbol
R1
L1
C1
C2
Part
Constant
100 Ω
0.1 μH
0.1 μF
10 μF
Resistor
Inductance
Capacitor
Capacitor
Capacitor
C3
10 μF
S11355-03
3.3 V
L1
+
+
C1 C2
C3
VCC_RX2
RXP
RXP
R1
S11355-03
RXN
RXN
GND_RX
STATUS
STATUS
GND
*Bold line: 50 Ω impedance matching
KPICC0180EC
Symbol
R1
L1
C1
C2
Part
Resistor
Inductance
Capacitor
Capacitor
Capacitor
Constant
100 Ω
0.1 μH
0.1 μF
10 μF
C3
10 μF
7
Photo IC for optical link
L11354-01, S11355-03, P11379-04AT
P11379-04AT
RXP
L1
3.3 V
Vcc_RX2
GND_RX2
RXP
RXN
R1
RXN
+
+
C3
C2
C1
Vcc_RX1
C4
STATUS
STATUS
GND_RX1
GND
Vcc_TX2
L2
TX_Ctrl
/RST
TX_Ctrl
/RST
TXP
3.3 V
+
+
C7
C6
C5
GND_TX2
Vcc_TX1
GND_TX1
TXP
R2
C8
GND
TXN
TXN
*Bold line: 50 Ω impedance matching
KPICC0187EA
Transmitter
Part
Resistor
Inductance
Capacitor
Capacitor
Capacitor
Capacitor
Receiver
Part
Resistor
Inductance
Capacitor
Capacitor
Capacitor
Capacitor
Symbol
R1
L1
C1
C2
Constant
100 ꢁ
0.1 ꢀH
10 ꢀF
10 ꢀF
0.1 ꢀF
0.1 ꢀF
Symbol
R2
L2
C5
C6
Constant
100 ꢁ
0.1 ꢀH
10 ꢀF
10 ꢀF
0.1 ꢀF
0.1 ꢀF
C3
C4
C7
C8
Eye diagram
Optical output waveform of L11354-01, P11379-04AT (Transmitter)
Output waveform of S11355-03, P11379-04AT (Receiver)
8
Photo IC for optical link
L11354-01, S11355-03, P11379-04AT
Dimensional outlines (unit: mm)
L11354-01
S11355-03
8.98 0.2 (including burr
)
8.98 0.2 (including burr
)
2.72
1.57
0.97
7.2 0.2 (including burr
)
7.2 0.2 (including burr
)
(2 ×)ϕ0.8 0.05
(2 ×)ϕ0.8 0.05
5.92
2.94
5.92
2.94
2.03 0.05
Emission area
0.6
2.03 0.05
Photosensitive area
A
A'
1.07
1.07
(7 ×) 0.5 0.05
(7 ×) 0.5 0.05
ϕ2.0 depth
0.15 max.
1.27 1.27 1.27 1.27 1.27 1.27
1.27 1.27 1.27 1.27 1.27 1.27
0.25 0.05
(Specified at lead root)
(Specified at lead root)
Tolerance unless otherwise noted: 0.1ꢀ 2°
R0.3 max.
Lead material: Cu alloy with Ag plating
Shaded area indicates burr.
STATUS
Vcc_RX1
GND_RX
RXN
/RST
(/RST)
TXN
0.23
TXP
RXP
Standard packing state: stick (50 pcs/stick)
GND_TX
Vcc_TX
Ctrl_TX
+0.05
-0.03
0.05
(Vcc_RX2)
Vcc_RX2
KPICA0079EC
A-A' cross section
KPICA0079EC
9
Photo IC for optical link
L11354-01, S11355-03, P11379-04AT
P11379-04AT
15.4 0.3
0.4 0.1
Index mark
1.27 0.1
6
0.03
Pin no.
Pin connections
Pin no.
13
14
15
16
17
18
19
20
21
22
23
24
Pin connections
RXP
RXN
/RST
(N/C)
GND_TX2
Vcc_TX2
GP2 (not used)
SHIELD
1
2
3
4
5
6
7
8
9
OEC
OEC
OEC
OEC
OEC
-
EOC
EOC
EOC
EOC
EOC
-
Vcc_RX1
GND_RX1
STATUS
SHIELD
SHIELD
TX_Ctrl
Vcc_TX1
GND_TX1
TXP
SHIELD
-
-
(Vcc_RX2)
GND_RX2
Vcc_RX2
(N/C)
EOC
EOC
EOC
EOC
EOC
OEC
OEC
OEC
OEC
OEC
10
11
12
Tolerance unless otherwise noted: 0.1ꢀ 2°
R0.3 max.
TXN
(GND_RX2)
Lead material: Cu alloy with Ni/Pd/Au plating
OEC: receiverꢀ EOC: transmitter
KPICA0086EC
KPICA0086EC
Recommended land pattern (unit: mm, P11379-04AT)
(24×) 0.8
(11×) 1.27
KPICC0189EB
10
Photo IC for optical link
L11354-01, S11355-03, P11379-04AT
Standard packing specifications
Reel (conforms to JEITA ET-7200)
Dimensions
380 mm
Hab diameter
80 mm
Tape width
32 mm
Material
PS
Electrostatic characteristics
Conductive
Embossed tape (unit: mm, material: PET)
2
0.1
4
Index mark
16 0.1
0.1
0.38 0.05
ϕ1.5+-00.1
5
0.3
Reel feed direction
9.8 0.2
10.6 0.1
KPINC0212EA
Packing quantity
500 pcs/reel
Packing type
Reel and desiccant in moisture-proof packing (vacuum-sealed)
11
Photo IC for optical link
L11354-01, S11355-03, P11379-04AT
Measured example of temperature profile with our hot-air reflow oven for product testing
300 °C
260 °C max.
217 °C
200 °C
150 °C
Preheat
160 s
Soldering
100 s max.
Time
KPICB0168EB
∙ This product supports lead-free soldering. After unpacking, store it in an environment at a temperature of 30 °C or less and a
humidity of 60% or less, and perform soldering within 4 weeks.
∙ The effect that the product receives during reflow soldering varies depending on the circuit board and reflow oven that are used.
Before actual reflow soldering, check for any problems by tesitng out the reflow soldering methods in advance.
Related information
www.hamamatsu.com/sp/ssd/doc_en.html
Precautions
∙ Notice
∙ Metal, Ceramic, Plastic products
∙ Surface mount type products
Information described in this material is current as of September, 2014.
Product specifications are subject to change without prior notice due to improvements or other reasons. This document has been carefully prepared and the
information contained is believed to be accurate. In rare casesꢀ howeverꢀ there may be inaccuracies such as text errors. Before using these productsꢀ always
contact us for the delivery specification sheet to check the latest specifications.
The product warranty is valid for one year after delivery and is limited to product repair or replacement for defects discovered and reported to us within that
one year period. Howeverꢀ even if within the warranty period we accept absolutely no liability for any loss caused by natural disasters or improper product
use.
Copying or reprinting the contents described in this material in whole or in part is prohibited without our prior permission.
www.hamamatsu.com
HAMAMATSU PHOTONICS K.K.ꢀ Solid State Division
1126-1 Ichino-choꢀ Higashi-kuꢀ Hamamatsu Cityꢀ 435-8558 Japanꢀ Telephone: (81) 53-434-3311ꢀ Fax: (81) 53-434-5184
U.S.A.: Hamamatsu Corporation: 360 Foothill Roadꢀ Bridgewaterꢀ N.J. 08807ꢀ U.S.A.ꢀ Telephone: (1) 908-231-0960ꢀ Fax: (1) 908-231-1218
Germany: Hamamatsu Photonics Deutschland GmbH: Arzbergerstr. 10ꢀ D-82211 Herrsching am Ammerseeꢀ Germanyꢀ Telephone: (49) 8152-375-0ꢀ Fax: (49) 8152-265-8
France: Hamamatsu Photonics France S.A.R.L.: 19ꢀ Rue du Saule Trapuꢀ Parc du Moulin de Massyꢀ 91882 Massy Cedexꢀ Franceꢀ Telephone: 33-(1) 69 53 71 00ꢀ Fax: 33-(1) 69 53 71 10
United Kingdom: Hamamatsu Photonics UK Limited: 2 Howard Courtꢀ 10 Tewin Roadꢀ Welwyn Garden Cityꢀ Hertfordshire AL7 1BWꢀ United Kingdomꢀ Telephone: (44) 1707-294888ꢀ Fax: (44) 1707-325777
North Europe: Hamamatsu Photonics Norden AB: Torshamnsgatan 35 16440 Kistaꢀ Swedenꢀ Telephone: (46) 8-509-031-00ꢀ Fax: (46) 8-509-031-01
Italy: Hamamatsu Photonics Italia S.r.l.: Strada della Moiaꢀ 1 int. 6ꢀ 20020 Arese (Milano)ꢀ Italyꢀ Telephone: (39) 02-93581733ꢀ Fax: (39) 02-93581741
China: Hamamatsu Photonics (China) Co.ꢀ Ltd.: B1201ꢀ Jiaming Centerꢀ No.27 Dongsanhuan Beiluꢀ Chaoyang Districtꢀ Beijing 100020ꢀ Chinaꢀ Telephone: (86) 10-6586-6006ꢀ Fax: (86) 10-6586-2866
12
Cat. No. KPIC1079E04 Sep. 2014 DN
相关型号：
L11354-01_ETC_KPIC1079E02
Quick Detection of Flame from Distance, Compact UV Sensor with High Sensitivity and Wide Directivity, Suitable for Flame Detectors and Fire Alarms.
HAMAMATSU
©2020 ICPDF网 联系我们和版权申明