C1103-04_15 [HAMAMATSU]
Accessories for infrared detectors;
| 型号： | C1103-04_15 |
| 厂家： | 
HAMAMATSU CORPORATION |
| 描述： | Accessories for infrared detectors |
| 文件： | 总8页 (文件大小：222K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
Accessories for infrared detectors
Temperature
controllers
Heatsinks for
TE-cooled detector
Chopper, etc.
Wide lineups of accessories for infrared detector
HAMAMATSU provides temperature controllers, heatsinks for TE-cooled detector, chopper and cables, etc as accessories for in-
frared detectors.
Connection example of accessories for infrared detectors
1
*
Power supply ( 15 ꢀ)
Measuring instrument
2
*
TE-cooled
detector*3
Chopper
C4696
Amplifier for
infrared detector*4
C4159/C5185 series
C3757-02
Heatsink for
TE-cooled
detector
Power supply
(100 ꢀ, 115 ꢀ, 230 ꢀ)
A3179 series
3
Temperature
controller
*
Chopper driver circuit
(accessory of the C4696)
C1103 series
Power supply (+12 ꢀ)
KACCC0321EC
*1: Attach the bare wire ends to a 3-pin or 4-pin connector or to a banana jack, and then connect them to the power supply.
*2: Soldering is needed. When using the C5185 series amplifier, a BNC connector (prepared by the user, example: one end of the E2573) is re-
quired.
*3: No socket is available. Soldering is needed.
*4: Refer to the datasheet “Amplifiers for infrared detectors” for detailed information.
Note: Refer to page 6 for details on cables.
1
www.hamamatsu.com
Temperature controllers,
heatsinks for TE-cooled detector, chopper, etc.
Accessories for infrared detectors
Temperature controllers C1103 series
The C1103 series is a temperature controller designed for thermoelectrically cooled infrared detectors. The C1103 series allows easy
but accurate temperature setting for the thermoelectric cooler mounted in an infrared detector.
Specifications
Parameter
C1103-04
C1103-05
C1103-07
One-stage/two-stage TE-cooled type
PbS, PbSe photoconductive detector, Two-stage/three-stage TE-cooled type
One-stage TE-cooled type
Applicable detector*5
InAs photovoltaic detector,
InGaAs, Si photodiode
MCT, InSb photoconductive detector MCT, InSb photoconductive detector
Setting element temperature
Temperature stability
Output current for temperature control
Power supply
Power consumption
Dimensions
-30 to +20 °C
-75 to -25 °C
Within ±0.1 °C
1.1 A min., 1.2 A typ., 1.3 A max.
100 V ± 10 % · 50/60 Hz*6
30 W
-30 to +20 °C
107 (W) × 84 (H) × 190 (D) mm
1.9 kg approx.
Weight
Instruction manual
Accessories
4-conductor cable (with a connector, 3 m) A4372-05*7, power supply cable
*5: It doesn't correspond to TE-cooled type infrared detector module with preamp.
*6: Please specify power supply requirement (AC line voltage) from among 100 V, 115 V and 230 V when ordering.
*7: When used in combination with an A3179 series heatsink, do not use the 4-conductor cable supplied with the A3179 series, but use
the A4372-05 instead.
Absolute maximum ratings
Parameter
Operating temperature
Operating humidity
Storage temperature
Value
+10 to +40 °C
90% Max.*8
-20 to +40 °C
*8: No condensation
Note: Exceeding the absolute maximum ratings even momentarily may cause a drop in product quality. Always be sure to use the
product within the absolute maximum ratings.
Block diagram
C1103 series
TE-cooled
detector
Thermistor
Current
circuit
Amp circuit
Comparator
TE-cooled element
Power
supply
AC input
KIRDC0008EB
2
Temperature controllers,
heatsinks for TE-cooled detector, chopper, etc.
Accessories for infrared detectors
Heatsinks for TE-cooled detector (TO-8, TO-3 package) A3179 series
These heatsinks are designed for use with thermoelectrically cooled detector sealed in a 6-pin TO-8, TO-3 package. The cooling (heat
dissipation) capacity of the A3179 and A3179-03 is about 35 °C relative to the ambient temperature 25 °C, the A3179-01 is about 40
°C, and that of the A3179-04 is about 85 °C. The A3179-03 is designed only for two-color detector K3413 series, the A3179, A3179-01
for TO-8, the A3179-04 for TO-3 (heatsink for TO-66 is available as a custom product.) .
Accessories
*9: When used in combination with a C1103 series temperature
Instruction manual
4-conductor cable (2 m): for TE-cooler and thermistor*9,
Coaxial cable (2 m): for signal*10
controller, do not use the 4-conductor cable supplied with the
A3179 series, but use the 4-conductor cable A4372-05 (sold
separately, with a connector).
10
*
*10: No socket is supplied for connection to infrared detectors.
Connect infrared detectors by soldering.
Cover the soldered joints and detector pins with vinyl insu-
lating tubes.
Dimensional outlines (unit: mm, tolerance unless otherwise noted: ±0.3)
A3179
Photosensitive
surface*3
(4 ×) ϕ3.5
0.4 0.3*2
32
1
*
Detector
metal package
3
3
60°
32.6
Weight: 50 g approx.
*1: Bottom surface (reference surface) of detector metal package
*2: When the detector is installed
*3: The position of the photosensitive surface differs according
to the detector used.
Refer to the dimensional outline for the detector.
KIRDA0018ED
3
Temperature controllers,
heatsinks for TE-cooled detector, chopper, etc.
Accessories for infrared detectors
A3179-01, A3179-03
Photosensitive
surface*3
(4 ×) ϕ3.5
1
0.4 0.3*2
32
*
Detector
metal package
3
B
60°
36
A3179-01: B=6
A3179-03: B=6.4
Weight: 53 g approx.
*1: Bottom surface (reference surface) of detector metal package
*2: When detector is installed
*3: The position of the photosensitive surface differs according
to the detector used.
Refer to the dimensional outline for the detector.
KIRDA0019ED
A3179-04
Fixation board
(4 ×) ϕ3.5 0.5
Photosensitive
surface
56
68
80
6.7 0.5
45
Weight: 320 g approx.
KIRDA0149EB
4
Temperature controllers,
heatsinks for TE-cooled detector, chopper, etc.
Accessories for infrared detectors
Chopper C4696
Specifications
Parameter
Chopping frequency*11
Power supply (VD)
Duty ratio
Specification
115 to 380 Hz, 345 Hz typ.*12
DC 5 to 13 V, 12 V typ.
1 : 1
Rotational stability
0.06 %/°C
Min.
Max.
VD - 0.5 V
VD - 0.2 V
Synchronous signal
(high level)
Operating temperature
Maximum current consumption*12
0 to 50 °C
90 mA
Accessory
Magnet stand A1447
*11: Chopping frequency will be 230 to 760 Hz when an optional disc is used.
*12: VD=12 V
Dimensional outline (unit: mm, tolerance unless otherwise noted: ±1)
<Chopper>
Input window
23.0 45.0
ϕ4.0
Output
window
ϕ8.0
A1447
(Magnet stand)
6-pin receptacle
cord length: 2 m
(For connection
to driver circuit)
<Driver circuit>
6-pin connector
GND
+12 ꢀ
ON-OFF
COUNTER
TRIG
BNC
85
KIRDA0022EA
5
Temperature controllers,
heatsinks for TE-cooled detector, chopper, etc.
Accessories for infrared detectors
Chopping frequency vs. operating voltage
(Typ.)
800
700
600
500
When used with
optional disk
400
300
200
C4696
100
0
2
4
6
8
10
12
14
Operating voltage (ꢀ)
KIRDB0376EA
Cables A4372 series
Cable No.
Cable
Length approx.
Note
Supplied with heatsink A3179 series.
When using this cable, make it as short as possible
(preferably about 10 cm).
Supplied with temperature controller C1103 series.
This cable is also sold separately.
This cable is supplied with the C4159/C5185 series amplifiers for
infrared detectors, C3757-02, and infrared detector modules with
preamp (room temperature operation type).
Coaxial cable (for signal)
2 m
3 m
4-conductor cable (with a connector)
A4372-05
4-conductor cable (with a connector)
A4372-02
2 m
This cable is also sold separately. Besides this cable, the A4372-
03, which is a 6-conductor cable (with connector) supplied with
“infrared detector module with preamp”, is also sold separately.
BNC connector cable E2573
Power supply cable
(for temperature controller)
1 m
Option
1.9 m
Supplied with temperature controller C1103 series
Chopper driver cable
(connected to chopper)
2-conductor cable or coaxial cable
(for chopper power supply)
2 m
Connected to chopper
Prepared by user
2 m or less
6
Temperature controllers,
heatsinks for TE-cooled detector, chopper, etc.
Accessories for infrared detectors
Magnet stand A1447
This is a magnet stand (sold separately) designed for the B749 photon drag detector.
Dimensional outline (unit: mm, tolerance unless otherwise noted: ±1)
1/4-20UNC
ϕ20
KIRDA0017EA
7
Temperature controllers,
heatsinks for TE-cooled detector, chopper, etc.
Accessories for infrared detectors
Valve operator for metal dewar A3515
With this valve operator, metal dewars can be re-evacuated to maintain the desired vacuum level. Refer to the instruction manual for details.
Please be aware that the detector performance is not guaranteed after re-evacuation is performed with the valve operator.
Vacuum pump
Valve operator
Metal dewar type infrared detector
Dimensional outline (unit: mm)
Pump tube
ϕ9.5 0.5
Knob
Leak mount
Gland nut
O-ring
80.0 1 (close)
115.0 1 (open)
KIRDA0021EC
Related information
www.hamamatsu.com/sp/ssd/doc_en.html
Precautions
∙ Notice
Technical information
∙ Infrared detector
Information described in this material is current as of November, 2014.
Product specifications are subject to change without prior notice due to improvements or other reasons. This document has been carefully prepared and the
information contained is believed to be accurate. In rare cases, however, there may be inaccuracies such as text errors. Before using these products, always
contact us for the delivery specification sheet to check the latest specifications.
The product warranty is valid for one year after delivery and is limited to product repair or replacement for defects discovered and reported to us within that
one year period. However, even if within the warranty period we accept absolutely no liability for any loss caused by natural disasters or improper product
use.
Copying or reprinting the contents described in this material in whole or in part is prohibited without our prior permission.
www.hamamatsu.com
HAMAMATSU PHOTONICS K.K., Solid State Division
1126-1 Ichino-cho, Higashi-ku, Hamamatsu City, 435-8558 Japan, Telephone: (81) 53-434-3311, Fax: (81) 53-434-5184
U.S.A.: Hamamatsu Corporation: 360 Foothill Road, Bridgewater, N.J. 08807, U.S.A., Telephone: (1) 908-231-0960, Fax: (1) 908-231-1218
Germany: Hamamatsu Photonics Deutschland GmbH: Arzbergerstr. 10, D-82211 Herrsching am Ammersee, Germany, Telephone: (49) 8152-375-0, Fax: (49) 8152-265-8
France: Hamamatsu Photonics France S.A.R.L.: 19, Rue du Saule Trapu, Parc du Moulin de Massy, 91882 Massy Cedex, France, Telephone: 33-(1) 69 53 71 00, Fax: 33-(1) 69 53 71 10
United Kingdom: Hamamatsu Photonics UK Limited: 2 Howard Court, 10 Tewin Road, Welwyn Garden City, Hertfordshire AL7 1BW, United Kingdom, Telephone: (44) 1707-294888, Fax: (44) 1707-325777
North Europe: Hamamatsu Photonics Norden AB: Torshamnsgatan 35 16440 Kista, Sweden, Telephone: (46) 8-509-031-00, Fax: (46) 8-509-031-01
Italy: Hamamatsu Photonics Italia S.r.l.: Strada della Moia, 1 int. 6, 20020 Arese (Milano), Italy, Telephone: (39) 02-93581733, Fax: (39) 02-93581741
China: Hamamatsu Photonics (China) Co., Ltd.: B1201, Jiaming Center, No.27 Dongsanhuan Beilu, Chaoyang District, Beijing 100020, China, Telephone: (86) 10-6586-6006, Fax: (86) 10-6586-2866
8
Cat. No. KACC1062E14 Nov. 2014 DN
相关型号：
©2020 ICPDF网 联系我们和版权申明