GS8182T08 [GSI]
18Mb SigmaDDR-II⢠Burst of 2 SRAM;型号: | GS8182T08 |
厂家: | GSI TECHNOLOGY |
描述: | 18Mb SigmaDDR-II⢠Burst of 2 SRAM 双倍数据速率 静态存储器 |
文件: | 总36页 (文件大小:717K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
GS8182T08/09/18/36BD-400/375/333/300/250/200/167
400 MHz–167 MHz
165-Bump BGA
Commercial Temp
Industrial Temp
18Mb SigmaDDR-II™
Burst of 2 SRAM
1.8 V V
DD
1.8 V and 1.5 V I/O
inputs, not differential inputs to a single differential clock input
buffer. The device also allows the user to manipulate the
output register clock inputs quasi independently with the C and
C clock inputs. C and C are also independent single-ended
clock inputs, not differential inputs. If the C clocks are tied
high, the K clocks are routed internally to fire the output
registers instead.
Features
• Simultaneous Read and Write SigmaDDR-II™ Interface
• Common I/O bus
• JEDEC-standard pinout and package
• Double Data Rate interface
• Byte Write (x36 and x18) and Nybble Write (x8) function
• Burst of 2 Read and Write
• 1.8 V +100/–100 mV core power supply
• 1.5 V or 1.8 V HSTL Interface
Each internal read and write operation in a SigmaDDR-II B2
RAM is two times wider than the device I/O bus. An input data
bus de-multiplexer is used to accumulate incoming data before
it is simultaneously written to the memory array. An output
data multiplexer is used to capture the data produced from a
single memory array read and then route it to the appropriate
output drivers as needed.
• Pipelined read operation with self-timed Late Write
• Fully coherent read and write pipelines
• ZQ pin for programmable output drive strength
• IEEE 1149.1 JTAG-compliant Boundary Scan
• Pin-compatible with present 9Mb, 36Mb, and 72Mb and
future 144Mb devices
• 165-bump, 13 mm x 15 mm, 1 mm bump pitch BGA package
• RoHS-compliant 165-bump BGA package available
When a new address is loaded into a x18 or x36 version of the
part, A0 is used to initialize the pointers that control the data
multiplexer / de-multiplexer so the RAM can perform "critical
word first" operations. From an external address point of view,
regardless of the starting point, the data transfers always follow
the same sequence {0, 1} or {1, 0} (where the digits shown
represent A0).
SigmaDDR-II™ Family Overview
The GS8182T08/09/18/36BD are built in compliance with the
SigmaDDR-II SRAM pinout standard for Common I/O
synchronous SRAMs. They are 18,874,368-bit (18Mb)
SRAMs. The GS8182T08/09/18/36BD SigmaDDR-II SRAMs
are just one element in a family of low power, low voltage
HSTL I/O SRAMs designed to operate at the speeds needed to
implement economical high performance networking systems.
Unlike the x18 and x36 versions, the input and output data
multiplexers of the x8 and x9 versions are not preset by
address inputs and therefore do not allow "critical word first"
operations. The address fields of the x8 and x9 SigmaDDR-II
B2 RAMs are one address pin less than the advertised index
depth (e.g., the 2M x 8 has a 1M addressable index, and A0 is
not an accessible address pin).
Clocking and Addressing Schemes
The GS8182T08/09/18/36BD SigmaDDR-II SRAMs are
synchronous devices. They employ two input register clock
inputs, K and K. K and K are independent single-ended clock
Parameter Synopsis
-400
2.5 ns
0.45 ns
-375
-333
3.0 ns
0.45 ns
-300
3.3 ns
0.45 ns
-250
4.0 ns
0.45 ns
-200
5.0 ns
0.45 ns
-167
tKHKH
tKHQV
2.67 ns
0.45 ns
6.0 ns
0.5 ns
Rev: 1.04c 11/2011
1/36
© 2007, GSI Technology
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
GS8182T08/09/18/36BD-400/375/333/300/250/200/167
512K x 36 SigmaDDR-II SRAM—Top View
1
2
3
4
5
6
7
8
9
10
11
NC/SA
(144Mb) (36Mb)
NC/SA
NC/SA
(72Mb)
A
B
CQ
R/W
BW2
K
BW1
LD
SA
CQ
NC/SA
(288Mb)
NC
DQ27
DQ18
SA
BW3
SA
K
BW0
SA
SA
NC
DQ8
C
D
E
F
NC
NC
NC
NC
NC
Doff
NC
NC
NC
NC
NC
NC
TDO
NC
DQ28
DQ19
DQ20
DQ21
DQ22
V
V
SA0
V
NC
NC
NC
NC
NC
DQ17
NC
DQ7
DQ16
DQ6
DQ5
DQ14
ZQ
SS
SS
SS
SS
DQ29
NC
V
V
V
V
V
V
V
V
V
V
V
V
V
V
SS
SS
DD
DD
DD
DD
DD
SS
SS
SS
SS
SS
SS
SS
SS
SS
SS
SS
DD
DD
DD
DD
DD
V
V
V
V
V
V
V
V
DQ15
NC
DDQ
DDQ
DDQ
DDQ
DDQ
DDQ
DDQ
DDQ
DQ30
DQ31
V
V
V
V
V
V
V
V
V
V
V
DDQ
DDQ
DDQ
DDQ
DDQ
G
H
J
V
V
V
NC
V
V
V
V
REF
REF
DDQ
DDQ
NC
NC
DQ32
DQ23
DQ24
DQ34
DQ25
DQ26
SA
NC
NC
NC
NC
NC
NC
SA
DQ13
DQ12
NC
DQ4
DQ3
DQ2
DQ1
DQ10
DQ0
TDI
K
L
V
DQ33
NC
V
V
V
V
V
DDQ
SS
SS
SS
SS
M
N
P
R
V
V
DQ11
NC
SS
SS
SS
SS
DQ35
NC
V
SA
SA
SA
SA
C
SA
SA
SA
V
SA
SA
SA
SA
DQ9
TMS
TCK
C
2
11 x 15 Bump BGA—13 x 15 mm Body—1 mm Bump Pitch
Notes:
1. BW0 controls writes to DQ0:DQ8; BW1 controls writes to DQ9:DQ17; BW2 controls writes to DQ18:DQ26; BW3 controls writes to
DQ27:DQ35.
Rev: 1.04c 11/2011
2/36
© 2007, GSI Technology
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
GS8182T08/09/18/36BD-400/375/333/300/250/200/167
1M x 18 SigmaDDR-II SRAM—Top View
1
2
3
4
5
6
7
8
9
10
11
NC/SA
(72Mb)
NC/SA
(144Mb)
NC/SA
(36Mb)
A
B
CQ
SA
R/W
BW1
K
LD
SA
CQ
NC/SA
(288Mb)
NC
DQ9
NC
SA
K
BW0
SA
SA
NC
NC
DQ8
C
D
E
F
NC
NC
NC
NC
NC
Doff
NC
NC
NC
NC
NC
NC
TDO
NC
NC
NC
V
V
SA
SA0
V
NC
NC
NC
NC
NC
DQ7
NC
NC
NC
NC
NC
NC
SS
SS
SS
SS
DQ10
DQ11
NC
V
V
V
V
V
V
V
V
V
V
V
V
V
V
SS
SS
DD
DD
DD
DD
DD
SS
SS
SS
SS
SS
SS
SS
SS
SS
SS
SS
DD
DD
DD
DD
DD
NC
V
V
V
V
V
V
V
V
DQ6
DQ5
NC
DDQ
DDQ
DDQ
DDQ
DDQ
DDQ
DDQ
DDQ
DQ12
NC
V
V
V
V
V
V
V
V
V
V
V
DDQ
DDQ
DDQ
DDQ
DDQ
G
H
J
DQ13
V
V
V
V
V
V
V
REF
ZQ
REF
DDQ
DDQ
NC
NC
NC
DQ14
NC
NC
DQ4
NC
NC
K
L
V
NC
NC
NC
NC
NC
SA
DQ3
DQ2
NC
DQ15
NC
V
V
V
V
V
NC
DDQ
SS
SS
SS
SS
M
N
P
R
NC
V
V
DQ1
NC
SS
SS
SS
SS
NC
DQ16
DQ17
SA
V
SA
SA
SA
SA
C
SA
SA
SA
V
NC
NC
SA
SA
SA
SA
NC
DQ0
TDI
TCK
C
TMS
2
11 x 15 Bump BGA—13 x 15 mm Body—1 mm Bump Pitch
Notes:
1. BW0 controls writes to DQ0:DQ8; BW1 controls writes to DQ9:DQ17
Rev: 1.04c 11/2011
3/36
© 2007, GSI Technology
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
GS8182T08/09/18/36BD-400/375/333/300/250/200/167
2M x 9 SigmaDDR-II SRAM—Top View
1
2
3
4
5
6
7
8
9
10
11
NC/SA
(72Mb)
NC/SA
(144Mb)
NC/SA
(36Mb)
A
B
CQ
SA
R/W
NC
K
LD
SA
CQ
NC/SA
(288Mb)
NC
NC
NC
SA
K
BW
SA
SA
NC
NC
DQ4
C
D
E
F
NC
NC
NC
NC
NC
Doff
NC
NC
NC
NC
NC
NC
TDO
NC
NC
NC
NC
NC
NC
NC
V
V
SA
SA
V
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
SS
SS
SS
SS
V
V
V
V
V
V
SS
SS
DD
DD
DD
DD
DD
SS
SS
SS
SS
SS
SS
SS
SS
SS
SS
SS
DD
DD
DD
DD
DD
DQ5
NC
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
DQ3
NC
DDQ
DDQ
DDQ
DDQ
DDQ
DDQ
DDQ
DDQ
V
V
V
V
V
V
V
V
V
V
V
DDQ
DDQ
DDQ
DDQ
DDQ
G
H
J
DQ6
V
V
V
NC
V
V
V
V
REF
ZQ
REF
DDQ
DDQ
NC
NC
NC
NC
NC
NC
NC
DQ8
SA
NC
DQ2
NC
NC
K
L
V
NC
NC
NC
NC
NC
SA
NC
DQ7
NC
V
V
V
V
V
NC
DQ1
NC
DDQ
SS
SS
SS
SS
M
N
P
R
V
V
NC
SS
SS
SS
SS
NC
V
SA
SA
SA
SA
C
SA
SA
SA
V
NC
NC
NC
SA
SA
SA
SA
NC
DQ0
TDI
TCK
C
TMS
2
11 x 15 Bump BGA—13 x 15 mm Body—1 mm Bump Pitch
Notes:
1. Unlike the x36 and x18 versions of this device, the x8 and x9 versions do not give the user access to A0. SA0 is set to 0 at the beginning
of each access.
Rev: 1.04c 11/2011
4/36
© 2007, GSI Technology
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
GS8182T08/09/18/36BD-400/375/333/300/250/200/167
2M x 8 SigmaDDR-II SRAM—Top View
1
2
3
4
5
6
7
8
9
10
11
NC/SA
(72Mb)
NC/SA
(144Mb)
NC/SA
(36Mb)
A
B
CQ
SA
R/W
NW1
K
LD
SA
CQ
NC/SA
(288Mb)
NC
NC
NC
SA
K
NW0
SA
SA
NC
NC
DQ3
C
D
E
F
NC
NC
NC
NC
NC
Doff
NC
NC
NC
NC
NC
NC
TDO
NC
NC
NC
NC
NC
NC
NC
V
V
SA
SA
V
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
DQ2
NC
NC
ZQ
SS
SS
SS
SS
V
V
V
V
V
V
SS
SS
DD
DD
DD
DD
DD
SS
SS
SS
SS
SS
SS
SS
SS
SS
SS
SS
DD
DD
DD
DD
DD
DQ4
NC
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
DDQ
DDQ
DDQ
DDQ
DDQ
DDQ
DDQ
DDQ
V
V
V
V
V
V
V
V
V
V
V
DDQ
DDQ
DDQ
DDQ
DDQ
G
H
J
DQ5
V
V
V
V
V
V
V
REF
REF
DDQ
DDQ
NC
NC
NC
NC
NC
NC
NC
DQ7
SA
NC
DQ1
NC
NC
NC
DQ0
NC
NC
NC
TDI
K
L
V
NC
NC
NC
NC
NC
SA
DQ6
NC
V
V
V
V
V
NC
DDQ
SS
SS
SS
SS
M
N
P
R
V
V
NC
SS
SS
SS
SS
NC
V
SA
SA
SA
SA
C
SA
SA
SA
V
NC
NC
SA
SA
SA
SA
NC
TCK
C
TMS
2
11 x 15 Bump BGA—13 x 15 mm Body—1 mm Bump Pitch
Notes:
1. Unlike the x36 and x18 versions of this device, the x8 and x9 versions do not give the user access to A0. SA0 is set to 0 at the beginning
of each access.
2. NW0 controls writes to DQ0:DQ3; NW1 controls writes to DQ4:DQ7.
Rev: 1.04c 11/2011
5/36
© 2007, GSI Technology
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
GS8182T08/09/18/36BD-400/375/333/300/250/200/167
Pin Description Table
Symbol
SA
Description
Type
Input
Input
Comments
Synchronous Address Inputs
Read/Write Control Pin
—
R/W
Write Active Low; Read Active High
Active Low
x18/x36 only
BW0–BW3
NW0–NW1
BW
Synchronous Byte Writes
Nybble Write Control Pin
Byte Write Control Pin
Input
Input
Input
Active Low
x8 only
Active Low
x9 only
LD
K
Synchronous Load Pin
Input Clock
Input
Input
Active Low
Active High
K
Input Clock
Input
Active Low
C
Output Clock
Input
Active High
C
Output Clock
Input
Active Low
TMS
TDI
TCK
TDO
VREF
Test Mode Select
Test Data Input
Input
—
Input
—
Test Clock Input
Input
—
Test Data Output
HSTL Input Reference Voltage
Output Impedance Matching Input
Data I/O
Output
Input
—
—
—
ZQ
DQ
Input
Input/Output
Input
Three State
Active Low
—
Disable DLL when low
Output Echo Clock
Output Echo Clock
Power Supply
Doff
CQ
Output
Output
Supply
CQ
—
VDD
1.8 V Nominal
VDDQ
VSS
Isolated Output Buffer Supply
Power Supply: Ground
No Connect
Supply
Supply
—
1.5 V or 1.8 V Nominal
—
—
NC
Notes:
1. NC = Not Connected to die or any other pin
2. When ZQ pin is directly connected to V , output impedance is set to minimum value and it cannot be connected to ground or left
DDQ
unconnected.
3. C, C, K, K cannot be set to VREF voltage.
Rev: 1.04c 11/2011
6/36
© 2007, GSI Technology
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
GS8182T08/09/18/36BD-400/375/333/300/250/200/167
Background
Common I/O SRAMs, from a system architecture point of view, are attractive in read dominated or block transfer applications.
Therefore, the SigmaDDR-II SRAM interface and truth table are optimized for burst reads and writes. Common I/O SRAMs are
unpopular in applications where alternating reads and writes are needed because bus turnaround delays can cut high speed
Common I/O SRAM data bandwidth in half.
Burst Operations
Read and write operations are "burst" operations. In every case where a read or write command is accepted by the SRAM, it will
respond by issuing or accepting two beats of data, executing a data transfer on subsequent rising edges of K and K, as illustrated in
the timing diagrams.This means that it is possible to load new addresses every K clock cycle. Addresses can be loaded less often, if
intervening deselect cycles are inserted.
Deselect Cycles
Chip Deselect commands are pipelined to the same degree as read commands. This means that if a deselect command is applied to
the SRAM on the next cycle after a read command captured by the SRAM, the device will complete the two beat read data transfer
and then execute the deselect command, returning the output drivers to high-Z. A high on the LD pin prevents the RAM from
loading read or write command inputs and puts the RAM into deselect mode as soon as it completes all outstanding burst transfer
operations.
SigmaDDR-II B2 SRAM Read Cycles
The SRAM executes pipelined reads. The status of the Address, LD and R/W pins are evaluated on the rising edge of K. The read
command (LD low and R/W high) is clocked into the SRAM by a rising edge of K. After the next rising edge of K, the SRAM
produces data out in response to the next rising edge of C (or the next rising edge of K, if C and C are tied high). The second beat
of data is transferred on the next rising edge of C, for a total of two transfers per address load.
SigmaDDR-II B2 SRAM Write Cycles
The status of the Address, LD and R/W pins are evaluated on the rising edge of K. The SRAM executes "late write" data transfers.
Data in is due at the device inputs on the rising edge of K following the rising edge of K clock used to clock in the write command
(LD and R/W low) and the write address. To complete the remaining beat of the burst of two write transfer, the SRAM captures
data in on the next rising edge of K, for a total of two transfers per address load.
Rev: 1.04c 11/2011
7/36
© 2007, GSI Technology
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
GS8182T08/09/18/36BD-400/375/333/300/250/200/167
Power-Up Sequence for SigmaQuad-II SRAMs
SigmaQuad-II SRAMs must be powered-up in a specific sequence in order to avoid undefined operations.
Power-Up Sequence
1. Power-up and maintain Doff at low state.
1a. Apply V
1b. Apply V
1c. Apply V
.
DD
.
DDQ
(may also be applied at the same time as V
).
REF
DDQ
2. After power is achieved and clocks (K, K, C, C) are stablized, change Doff to high.
3. An additional 1024 clock cycles are required to lock the DLL after it has been enabled.
Note:
If you want to tie Doff high with an unstable clock, you must stop the clock for a minimum of 30 ns to reset the DLL after
the clocks become stablized.
DLL Constraints
• The DLL synchronizes to either K or C clock. These clocks should have low phase jitter . The DLL cannot operate at a
frequency lower than that specified by the t
maximum specification for the desired operating clock frequency.
KHKH
• If the incoming clock is not stablized when DLL is enabled, the DLL may lock on the wrong frequency and cause
undefined errors or failures during the initial stage.
Note:
If the frequency is changed, DLL reset is required. After reset, a minimum of 1024 cycles is required for DLL lock.
Rev: 1.04c 11/2011
8/36
© 2007, GSI Technology
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
GS8182T08/09/18/36BD-400/375/333/300/250/200/167
Special Functions
Byte Write and Nybble Write Control
Byte Write Enable pins are sampled at the same time that Data In is sampled. A high on the Byte Write Enable pin associated with
a particular byte (e.g., BW0 controls D0–D8 inputs) will inhibit the storage of that particular byte, leaving whatever data may be
stored at the current address at that byte location undisturbed. Any or all of the Byte Write Enable pins may be driven high or low
during the data in sample times in a write sequence.
Each write enable command and write address loaded into the RAM provides the base address for a 2 beat data transfer. The x18
version of the RAM, for example, may write 36 bits in association with each address loaded. Any 9-bit byte may be masked in any
write sequence.
Nybble Write (4-bit) write control is implemented on the 8-bit-wide version of the device. For the x8 version of the device,
“Nybble Write Enable” and “NBx” may be substituted in all the discussion above.
Example x18 RAM Write Sequence using Byte Write Enables
Data In Sample Time
BW0
BW1
D0–D8
Data In
D9–D17
Don’t Care
Data In
Beat 1
Beat 2
0
1
1
0
Don’t Care
Resulting Write Operation
Byte 1
D0–D8
Byte 2
D9–D17
Byte 3
D0–D8
Byte 4
D9–D17
Written
Unchanged
Unchanged
Written
Beat 1
Beat 2
Output Register Control
SigmaDDR-II SRAMs offer two mechanisms for controlling the output data registers. Typically, control is handled by the Output
Register Clock inputs, C and C. The Output Register Clock inputs can be used to make small phase adjustments in the firing of the
output registers by allowing the user to delay driving data out as much as a few nanoseconds beyond the next rising edges of the K
and K clocks. If the C and C clock inputs isare tied high, the RAM reverts to K and K control of the outputs, allowing the RAM to
function as a conventional pipelined read SRAM.
Rev: 1.04c 11/2011
9/36
© 2007, GSI Technology
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
GS8182T08/09/18/36BD-400/375/333/300/250/200/167
Example Four Bank Depth Expansion Schematic
LD
3
R /W
3
3
LD
2
R /W
2
2
1
0
LD
1
R /W
1
LD
0
R /W
0
A –A
0
n
K
Bank 3
Bank 1
Bank 2
Bank 0
A
A
A
A
R/W
R/W
R/W
R/W
LD
LD
LD
LD
CQ
K
CQ
K
CQ
DQ
CQ
DQ
K
K
DQ
DQ
DQ -DQ
1
n
CQ
0
CQ
1
CQ
CQ
2
3
Note:
For simplicity BWn not shown.
Rev: 1.04c 11/2011
10/36
© 2007, GSI Technology
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
GS8182T08/09/18/36BD-400/375/333/300/250/200/167
FLXDrive-II Output Driver Impedance Control
HSTL I/O SigmaDDR-II SRAMs are supplied with programmable impedance output drivers. The ZQ pin must be connected to
V
via an external resistor, RQ, to allow the SRAM to monitor and adjust its output driver impedance. The value of RQ must be
SS
5X the value of the desired RAM output impedance. The allowable range of RQ to guarantee impedance matching continuously is
between 175Ω and 350Ω. Periodic readjustment of the output driver impedance is necessary as the impedance is affected by drifts
in supply voltage and temperature. The SRAM’s output impedance circuitry compensates for drifts in supply voltage and tempera-
ture. A clock cycle counter periodically triggers an impedance evaluation, resets and counts again. Each impedance evaluation may
move the output driver impedance level one step at a time towards the optimum level.
Common I/O SigmaDDR-II B2 SRAM Truth Table
DQ
K
LD
R/W
Operation
n
A + 0
Hi-Z
A + 1
Hi-Z
↑
1
0
X
0
Deselect
Write
D@Kn+1
D@Kn+1
↑
Q@Kn+1
Q@Kn+2
↑
0
1
or
Cn+1
or
Cn+2
Read
Note:
Q is controlled by K clocks if C clocks are not used.
B2 Byte Write Clock Truth Table
BW
BW
Current Operation
D
D
K ↑
n+1
K ↑
n+2
K ↑
n
K ↑
n+1
K ↑
n+2
(t
)
(t
)
(t )
(t
)
(t
)
Write
T
T
D1
D2
Dx stored if BWn = 0 in both data transfers
Write
T
F
F
F
T
F
D1
X
X
D2
X
Dx stored if BWn = 0 in 1st data transfer only
Write
Dx stored if BWn = 0 in 2nd data transfer only
Write Abort
No Dx stored in either data transfer
X
Notes:
1. “1” = input “high”; “0” = input “low”; “X” = input “don’t care”; “T” = input “true”; “F” = input “false”.
2. If one or more BWn = 0, then BW = “T”, else BW = “F”.
Rev: 1.04c 11/2011
11/36
© 2007, GSI Technology
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
GS8182T08/09/18/36BD-400/375/333/300/250/200/167
B2 Nybble Write Clock Truth Table
NW
NW
Current Operation
D
D
K ↑
n+1
K ↑
n+2
K ↑
n
K ↑
n+1
K ↑
n+2
(t
)
(t
)
(t )
(t
)
(t
)
Write
T
T
D1
D2
Dx stored if NWn = 0 in both data transfers
Write
T
F
F
F
T
F
D1
X
X
D2
X
Dx stored if NWn = 0 in 1st data transfer only
Write
Dx stored if NWn = 0 in 2nd data transfer only
Write Abort
No Dx stored in either data transfer
X
Notes:
1. “1” = input “high”; “0” = input “low”; “X” = input “don’t care”; “T” = input “true”; “F” = input “false”.
2. If one or more NWn = 0, then NW = “T”, else NW = “F”.
x36 Byte Write Enable (BWn) Truth Table
BW0
BW1
BW2
BW3
D0–D8
Don’t Care
Data In
D9–D17
Don’t Care
Don’t Care
Data In
D18–D26
Don’t Care
Don’t Care
Don’t Care
Don’t Care
Data In
D27–D35
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
1
1
0
0
0
0
1
1
1
1
0
0
0
0
1
1
1
1
1
1
1
1
0
0
0
0
0
0
0
0
Don’t Care
Don’t Care
Don’t Care
Don’t Care
Don’t Care
Don’t Care
Don’t Care
Don’t Care
Data In
Don’t Care
Data In
Data In
Don’t Care
Data In
Don’t Care
Don’t Care
Data In
Data In
Don’t Care
Data In
Data In
Data In
Data In
Don’t Care
Data In
Don’t Care
Don’t Care
Data In
Don’t Care
Don’t Care
Don’t Care
Don’t Care
Data In
Data In
Don’t Care
Data In
Data In
Data In
Data In
Don’t Care
Data In
Don’t Care
Don’t Care
Data In
Data In
Data In
Data In
Don’t Care
Data In
Data In
Data In
Data In
Data In
Data In
Rev: 1.04c 11/2011
12/36
© 2007, GSI Technology
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
GS8182T08/09/18/36BD-400/375/333/300/250/200/167
x18 Byte Write Enable (BWn) Truth Table
BW0
BW1
D0–D8
D9–D17
Don’t Care
Don’t Care
Data In
1
0
1
0
1
1
0
0
Don’t Care
Data In
Don’t Care
Data In
Data In
x8 Nybble Write Enable (NWn) Truth Table
NW0
NW1
D0–D3
Don’t Care
Data In
D4–D7
Don’t Care
Don’t Care
Data In
1
0
1
0
1
1
0
0
Don’t Care
Data In
Data In
Rev: 1.04c 11/2011
13/36
© 2007, GSI Technology
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
GS8182T08/09/18/36BD-400/375/333/300/250/200/167
Absolute Maximum Ratings
(All voltages reference to V
)
SS
Symbol
VDD
Description
Value
–0.5 to 2.9
Unit
Voltage on VDD Pins
Voltage in VDDQ Pins
Voltage in VREF Pins
V
VDDQ
VREF
VI/O
–0.5 to VDD
V
V
–0.5 to VDDQ
–0.5 to VDDQ +0.5 (≤ 2.9 V max.)
–0.5 to VDDQ +0.5 (≤ 2.9 V max.)
Voltage on I/O Pins
V
VIN
Voltage on Other Input Pins
Input Current on Any Pin
V
IIN
+/–100
+/–100
125
mA dc
mA dc
IOUT
Output Current on Any I/O Pin
Maximum Junction Temperature
Storage Temperature
oC
oC
TJ
TSTG
–55 to 125
Note:
Permanent damage to the device may occur if the Absolute Maximum Ratings are exceeded. Operation should be restricted to Recommended
Operating Conditions. Exposure to conditions exceeding the Recommended Operating Conditions, for an extended period of time, may affect
reliability of this component.
Recommended Operating Conditions
Power Supplies
Parameter
Supply Voltage
Symbol
VDD
Min.
1.7
Typ.
1.8
—
Max.
1.9
Unit
V
VDDQ
VREF
I/O Supply Voltage
Reference Voltage
1.4
1.9
V
0.68
—
0.95
V
Notes:
1. Unless otherwise noted, all performance specifications quoted are evaluated for worst case at both 1.4 V ≤ V
≤ 1.6 V (i.e., 1.5 V I/O)
DDQ
and 1.7 V ≤ V
≤ 1.9 V (i.e., 1.8 V I/O) and quoted at whichever condition is worst case.
DDQ
2. The power supplies need to be powered up simultaneously or in the following sequence: V , V , V , followed by signal inputs. The
DD DDQ REF
power down sequence must be the reverse. V
must not exceed V .
DD
DDQ
Operating Temperature
Parameter
Symbol
Min.
Typ.
Max.
Unit
Ambient Temperature
(Commercial Range Versions)
TA
0
25
70
°C
Ambient Temperature
(Industrial Range Versions)
TA
–40
25
85
°C
Rev: 1.04c 11/2011
14/36
© 2007, GSI Technology
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
GS8182T08/09/18/36BD-400/375/333/300/250/200/167
HSTL I/O DC Input Characteristics
Parameter
DC Input Logic High
Symbol
VIH (dc)
VIL (dc)
Min
Max
Units
Notes
1, 4
VREF + 0.10
VDDQ + 0.3 V
VREF – 0.10
V
V
–0.3 V
1, 3
DC Input Logic Low
Notes:
1. Compatible with both 1.8 V and 1.5 V I/O drivers.
2. These are DC test criteria. DC design criteria is V
± 50 mV. The AC V /V levels are defined separately for measuring timing
REF
IH IL
parameters.
3. V (Min) DC = –0.3 V, V (Min) AC = –1.5 V (pulse width ≤ 3 ns).
IL
IL
4.
V
(Max) DC = V
+ 0.3 V, V (Max) AC = V
+ 0.85 V (pulse width ≤ 3 ns).
IH
DDQ
IH
DDQ
HSTL I/O AC Input Characteristics
Parameter
AC Input Logic High
Symbol
VIH (ac)
VIL (ac)
Min
Max
—
Units
Notes
2, 3
2, 3
1
VREF + 0.20
V
V
V
VREF – 0.20
5% VREF (DC)
—
—
AC Input Logic Low
V
Peak-to-Peak AC Voltage
VREF (ac)
REF
Notes:
1. The peak-to-peak AC component superimposed on V
may not exceed 5% of the DC component of V
.
REF
REF
2. To guarantee AC characteristics, V ,V , Trise, and Tfall of inputs and clocks must be within 10% of each other.
IH IL
3. For devices supplied with HSTL I/O input buffers. Compatible with both 1.8 V and 1.5 V I/O drivers.
Undershoot Measurement and Timing
Overshoot Measurement and Timing
V
IH
20% tKHKH
V
+ 1.0 V
DD
V
SS
50%
50%
V
DD
V
– 1.0 V
SS
20% tKHKH
V
IL
Capacitance
o
(T = 25 C, f = 1 MHZ, V = 3.3 V)
A
DD
Parameter
Symbol
CIN
Test conditions
VIN = 0 V
Typ.
Max.
Unit
pF
Input Capacitance
Output Capacitance
Clock Capacitance
4
6
5
5
7
6
COUT
CCLK
VOUT = 0 V
pF
—
pF
Note:
This parameter is sample tested.
Rev: 1.04c 11/2011
15/36
© 2007, GSI Technology
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
GS8182T08/09/18/36BD-400/375/333/300/250/200/167
AC Test Conditions
Parameter
Input high level
Conditions
VDDQ
Input low level
0 V
Max. input slew rate
Input reference level
2 V/ns
VDDQ/2
VDDQ/2
Output reference level
Note:
Test conditions as specified with output loading as shown unless otherwise noted.
AC Test Load Diagram
DQ
RQ = 250 Ω (HSTL I/O)
= 0.75 V
V
REF
50Ω
VT = V /2
DDQ
Input and Output Leakage Characteristics
Parameter
Symbol
IIL
Test Conditions
Min.
Max
Input Leakage Current
(except mode pins)
VIN = 0 to VDD
–2 uA
2 uA
VDD ≥ VIN ≥ VIL
0 V ≤ VIN ≤ VIL
–100 uA
–2 uA
2 uA
2 uA
IINDOFF
Doff
Output Disable,
VOUT = 0 to VDDQ
IOL
Output Leakage Current
–2 uA
2 uA
Rev: 1.04c 11/2011
16/36
© 2007, GSI Technology
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
GS8182T08/09/18/36BD-400/375/333/300/250/200/167
Programmable Impedance HSTL Output Driver DC Electrical Characteristics
Parameter
Symbol
VOH1
Min.
Max.
VDDQ
Units
Notes
1, 3
VDDQ/2
V
V
V
V
Output High Voltage
Output Low Voltage
Output High Voltage
VOL1
VDDQ/2
VDDQ
Vss
2, 3
VOH2
VDDQ – 0.2
4, 5
VOL2
Vss
0.2
4, 6
Output Low Voltage
Notes:
1.
I
= (V /2) / (RQ/5) +/– 15% @ V = V /2 (for: 175Ω ≤ RQ ≤ 350Ω).
DDQ OH DDQ
OH
2.
I
= (V /2) / (RQ/5) +/– 15% @ V = V /2 (for: 175Ω ≤ RQ ≤ 350Ω).
OL
DDQ
OL
DDQ
3. Parameter tested with RQ = 250Ω and V
4. 0Ω ≤ RQ ≤ ∞Ω
= 1.5 V or 1.8 V
DDQ
5.
I
= –1.0 mA
OH
6.
I
= 1.0 mA
OL
Rev: 1.04c 11/2011
17/36
© 2007, GSI Technology
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
GS8182T08/09/18/36BD-400/375/333/300/250/200/167
Operating Currents
-400
-375
-333
-300
-250
-200
-167
Parameter
Symbol
Test Conditions
Notes
0
to
–40
to
0
to
–40
to
0
to
–40
to
0
to
–40
to
0
to
–40
to
0
to
–40
to
0
to
–40
to
70°C 85°C 70°C 85°C 70°C 85°C 70°C 85°C 70°C 85°C 70°C 85°C 70°C 85°C
V
= Max, I
= 0 mA
OUT
765
mA
775
mA
725
mA
735
mA
550
mA
560
mA
505
mA
515
mA
440
mA
450
mA
370
mA
380
mA
330
mA
340
mA
Operating Current
(x36): DDR
DD
I
2, 3
2, 3
2, 3
2, 3
DD
Cycle Time ≥ t
Min
KHKH
V
= Max, I
= 0 mA
Min
605
mA
615
mA
570
mA
580
mA
435
mA
445
mA
405
mA
415
mA
350
mA
360
mA
300
mA
310
mA
265
mA
275
mA
Operating Current
(x18): DDR
DD
OUT
I
DD
Cycle Time ≥ t
KHKH
V
= Max, I
= 0 mA
Min
605
mA
615
mA
570
mA
580
mA
435
mA
445
mA
405
mA
415
mA
350
mA
360
mA
300
mA
310
mA
265
mA
275
mA
Operating Current
(x9): DDR
DD
OUT
I
DD
Cycle Time ≥ t
KHKH
V
= Max, I
= 0 mA
Min
605
mA
615
mA
570
mA
580
mA
435
mA
445
mA
405
mA
415
mA
350
mA
360
mA
300
mA
310
mA
265
mA
275
mA
Operating Current
(x8): DDR
DD
OUT
I
DD
Cycle Time ≥ t
KHKH
Device deselected,
OUT
200
mA
210
mA
195
mA
205
mA
170
mA
180
mA
165
mA
175
mA
155
mA
165
mA
140
mA
150
mA
135
mA
145
mA
Standby Current
(NOP): DDR
I
= 0 mA, f = Max,
I
2, 4
SB1
All Inputs ≤ 0.2 V or
≥ V – 0.2 V
DD
Notes:
1.
2.
Power measured with output pins floating.
Minimum cycle, IOUT = 0 mA
3.
4.
Operating current is calculated with 50% read cycles and 50% write cycles.
Standby Current is only after all pending read and write burst operations are completed.
Rev: 1.04c 11/2011
18/36
© 2007, GSI Technology
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
GS8182T08/09/18/36BD-400/375/333/300/250/200/167
AC Electrical Characteristics
-400
-375
-333
-300
-250
-200
-167
Parameter
Symbol
Min Max Min Max Min Max Min Max Min Max Min Max Min Max
Clock
tKHKH
tCHCH
K, K Clock Cycle Time
C, C Clock Cycle Time
2.5
—
8.4
0.2
—
2.67
—
8.4
0.2
—
3.0
—
8.4
0.2
—
3.3
—
8.4
0.2
—
4.0
—
8.4
0.2
—
5.0
—
8.4
0.2
—
6.0
—
8.4
0.2
—
ns
ns
ns
tKCVar
tTKC Variable
6
tKHKL
tCHCL
K, K Clock High Pulse Width
C, C Clock High Pulse Width
1.0
1.13
1.2
1.32
1.6
2.0
2.4
tKLKH
tCLCH
K, K Clock Low Pulse Width
C, C Clock Low Pulse Width
1.0
1.0
1.0
—
—
—
1.13
1.13
1.13
—
—
—
1.2
—
—
—
1.32
1.49
1.49
—
—
—
1.6
1.8
1.8
—
—
—
2.0
2.2
2.2
—
—
—
2.4
2.7
2.7
—
—
—
ns
ns
tKHKH
tCHCH
K to K High
C to C High
1.35
1.35
tKHKH
tCHCH
K to K High
C to C High
ns
ns
tKHCH
tKCLock
tKCReset
K, K Clock High to C, C Clock High
DLL Lock Time
0
1.1
—
0
1.2
—
0
1.3
—
0
1.45
—
0
1.8
—
0
2.3
—
0
2.8
—
cy
cle
1024
30
1024
30
1024
30
1024
30
1024
30
1024
30
1024
30
6
K Static to DLL reset
—
—
—
—
—
—
—
ns
Output Times
tKHQV
K, K Clock High to Data Output Valid
—
0.45
—
—
0.45
—
—
0.45
—
—
0.45
—
—
0.45
—
—
0.45
—
—
–0.5
—
0.5
—
ns
ns
ns
ns
4
4
C, C Clock High to Data Output Valid tCHQV
tKHQX
C, C Clock High to Data Output Hold tCHQX
tKHCQV
C, C Clock High to Echo Clock Valid tCHCQV
tKHCQX
C, C Clock High to Echo Clock Hold tCHCQX
K, K Clock High to Data Output Hold
–0.45
—
–0.45
—
–0.45
—
–0.45
—
–0.45
—
–0.45
—
K, K Clock High to Echo Clock Valid
0.45
—
0.45
—
0.45
—
0.45
—
0.45
—
0.45
—
0.5
—
K, K Clock High to Echo Clock Hold
–0.45
–0.45
–0.45
–0.45
–0.45
–0.45
–0.5
tCQHQV
tCQHQX
tCQHCQH
tCQHCQH
tKHQZ
tCHQZ
tKHQX1
tCHQX1
CQ, CQ High Output Valid
CQ, CQ High Output Hold
—
0.25
—
—
0.25
—
—
0.25
—
—
0.27
—
—
0.30
—
—
0.35
—
—
0.40 ns
8
8
–0.25
–0.25
–0.25
–0.27
–0.30
–0.35
–0.40
—
—
ns
ns
CQ Phase Distortion
0.9
—
—
0.45
—
1.0
—
—
0.45
—
1.10
—
—
0.45
—
1.24
—
—
0.45
—
1.55
—
—
0.45
—
1.95
—
—
0.45
—
2.45
—
K Clock High to Data Output High-Z
C Clock High to Data Output High-Z
0.5
—
ns
ns
4
4
K Clock High to Data Output Low-Z
C Clock High to Data Output Low-Z
–0.45
–0.45
–0.45
–0.45
–0.45
–0.45
–0.5
Setup Times
tAVKH
tIVKH
Address Input Setup Time
0.4
0.4
—
—
0.4
0.4
—
—
0.4
0.4
—
—
0.4
0.4
—
—
0.5
0.5
—
—
0.6
0.6
—
—
0.7
0.7
—
—
ns
ns
1
2
Control Input Setup Time (R/W, LD)
Control Input Setup Time (BWX,
NWX)
tIVKH
0.28
0.28
—
—
0.28
0.28
—
—
0.28
0.28
—
—
0.3
0.3
—
—
0.35
0.35
—
—
0.4
0.4
—
—
0.5
0.5
—
—
ns
ns
3
tDVKH
Data Input Setup Time
Rev: 1.04c 11/2011
19/36
© 2007, GSI Technology
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
GS8182T08/09/18/36BD-400/375/333/300/250/200/167
AC Electrical Characteristics (Continued)
-400
-375
-333
-300
-250
-200
-167
Parameter
Symbol
Min Max Min Max Min Max Min Max Min Max Min Max Min Max
Hold Times
tKHAX
tKHIX
Address Input Hold Time
0.4
0.4
—
—
0.4
0.4
—
—
0.4
0.4
—
—
0.4
0.4
—
—
0.5
0.5
—
—
0.6
0.6
—
—
0.7
0.7
—
—
ns
ns
1
2
Control Input Hold Time (R/W, LD)
Control Input Hold Time (BWX,
NWX)
tIVKH
0.28
0.28
—
—
0.28
0.28
—
—
0.28
0.28
—
—
0.3
0.3
—
—
0.35
0.35
—
—
0.4
0.4
—
—
0.5
0.5
—
—
ns
ns
3
tKHDX
Data Input Hold Time
Notes:
1.
2.
3.
4.
5.
All Address inputs must meet the specified setup and hold times for all latching clock edges.
Control singles are RW, LD.
Control singles BW0, BW1, (NW0, NW1 for x8) and BW2, BW3 for x36.
If C, C are tied high, K, K become the references for C, C timing parameters.
To avoid bus contention, at a given voltage and temperature tCHQX1 is bigger than tCHQZ. The specs as shown do not imply bus contention because tCHQX1 is a MIN parameter
that is worst case at totally different test conditions (0°C, 1.9 V) than tCHQZ, which is a MAX parameter (worst case at 70°C, 1.7 V). It is not possible for two SRAMs on the same
board to be at such different voltages and temperatures.
6.
7.
Clock phase jitter is the variance from clock rising edge to the next expected clock rising edge.
VDD slew rate must be less than 0.1 V DC per 50 ns for DLL lock retention. DLL lock time begins once VDD and input clock are stable.
8.
Echo clock is very tightly controlled to data valid/data hold. By design, there is a ±0.1 ns variation from echo clock to data. The datasheet parameters reflect tester guard bands
and test setup variations.
Rev: 1.04c 11/2011
20/36
© 2007, GSI Technology
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
GS8182T08/09/18/36BD-400/375/333/300/250/200/167
Rev: 1.04c 11/2011
21/36
© 2007, GSI Technology
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
GS8182T08/09/18/36BD-400/375/333/300/250/200/167
Rev: 1.04c 11/2011
22/36
© 2007, GSI Technology
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
GS8182T08/09/18/36BD-400/375/333/300/250/200/167
Rev: 1.04c 11/2011
23/36
© 2007, GSI Technology
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
GS8182T08/09/18/36BD-400/375/333/300/250/200/167
Rev: 1.04c 11/2011
24/36
© 2007, GSI Technology
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
GS8182T08/09/18/36BD-400/375/333/300/250/200/167
JTAG Port Operation
Overview
The JTAG Port on this RAM operates in a manner that is compliant with IEEE Standard 1149.1-1990, a serial boundary scan
interface standard (commonly referred to as JTAG). The JTAG Port input interface levels scale with V . The JTAG output
DD
drivers are powered by V
.
DD
Disabling the JTAG Port
It is possible to use this device without utilizing the JTAG port. The port is reset at power-up and will remain inactive unless
clocked. TCK, TDI, and TMS are designed with internal pull-up circuits.To assure normal operation of the RAM with the JTAG
Port unused, TCK, TDI, and TMS may be left floating or tied to either V or V . TDO should be left unconnected.
DD
SS
JTAG Pin Descriptions
Pin
Pin Name
I/O
Description
Clocks all TAP events. All inputs are captured on the rising edge of TCK and all outputs propagate from the
falling edge of TCK.
TCK
Test Clock
In
The TMS input is sampled on the rising edge of TCK. This is the command input for the TAP controller state
machine. An undriven TMS input will produce the same result as a logic one input level.
TMS
TDI
Test Mode Select
Test Data In
In
The TDI input is sampled on the rising edge of TCK. This is the input side of the serial registers placed
between TDI and TDO. The register placed between TDI and TDO is determined by the state of the TAP
In Controller state machine and the instruction that is currently loaded in the TAP Instruction Register (refer to
the TAP Controller State Diagram). An undriven TDI pin will produce the same result as a logic one input
level.
Output that is active depending on the state of the TAP state machine. Output changes in response to the
falling edge of TCK. This is the output side of the serial registers placed between TDI and TDO.
TDO
Test Data Out
Out
Note:
This device does not have a TRST (TAP Reset) pin. TRST is optional in IEEE 1149.1. The Test-Logic-Reset state is entered while TMS is
held high for five rising edges of TCK. The TAP Controller is also reset automaticly at power-up.
JTAG Port Registers
Overview
The various JTAG registers, refered to as Test Access Port or TAP Registers, are selected (one at a time) via the sequences of 1s
and 0s applied to TMS as TCK is strobed. Each of the TAP Registers is a serial shift register that captures serial input data on the
rising edge of TCK and pushes serial data out on the next falling edge of TCK. When a register is selected, it is placed between the
TDI and TDO pins.
Instruction Register
The Instruction Register holds the instructions that are executed by the TAP controller when it is moved into the Run, Test/Idle, or
the various data register states. Instructions are 3 bits long. The Instruction Register can be loaded when it is placed between the
TDI and TDO pins. The Instruction Register is automatically preloaded with the IDCODE instruction at power-up or whenever the
controller is placed in Test-Logic-Reset state.
Bypass Register
The Bypass Register is a single bit register that can be placed between TDI and TDO. It allows serial test data to be passed through
the RAM’s JTAG Port to another device in the scan chain with as little delay as possible.
Boundary Scan Register
The Boundary Scan Register is a collection of flip flops that can be preset by the logic level found on the RAM’s input or I/O pins.
The flip flops are then daisy chained together so the levels found can be shifted serially out of the JTAG Port’s TDO pin. The
Boundary Scan Register also includes a number of place holder flip flops (always set to a logic 1). The relationship between the
device pins and the bits in the Boundary Scan Register is described in the Scan Order Table following. The Boundary Scan
Rev: 1.04c 11/2011
25/36
© 2007, GSI Technology
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
GS8182T08/09/18/36BD-400/375/333/300/250/200/167
Register, under the control of the TAP Controller, is loaded with the contents of the RAMs I/O ring when the controller is in
Capture-DR state and then is placed between the TDI and TDO pins when the controller is moved to Shift-DR state. SAMPLE-Z,
SAMPLE/PRELOAD and EXTEST instructions can be used to activate the Boundary Scan Register.
JTAG TAP Block Diagram
·
·
·
·
·
·
·
·
Boundary Scan Register
·
·
·
0
Bypass Register
2
1 0
Instruction Register
TDI
TDO
ID Code Register
31 30 29
2 1
0
·
· · ·
Control Signals
Test Access Port (TAP) Controller
TMS
TCK
Identification (ID) Register
The ID Register is a 32-bit register that is loaded with a device and vendor specific 32-bit code when the controller is put in
Capture-DR state with the IDCODE command loaded in the Instruction Register. The code is loaded from a 32-bit on-chip ROM.
It describes various attributes of the RAM as indicated below. The register is then placed between the TDI and TDO pins when the
controller is moved into Shift-DR state. Bit 0 in the register is the LSB and the first to reach TDO when shifting begins.
ID Register Contents
GSI Technology
See BSDL Model
JEDEC Vendor
ID Code
31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10
9
0
8
1
7
1
6
0
5
1
4
1
3
0
2
0
1
1
0
1
Bit #
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
0
0
Rev: 1.04c 11/2011
26/36
© 2007, GSI Technology
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
GS8182T08/09/18/36BD-400/375/333/300/250/200/167
Tap Controller Instruction Set
Overview
There are two classes of instructions defined in the Standard 1149.1-1990; the standard (Public) instructions, and device specific
(Private) instructions. Some Public instructions are mandatory for 1149.1 compliance. Optional Public instructions must be
implemented in prescribed ways. The TAP on this device may be used to monitor all input and I/O pads, and can be used to load
address, data or control signals into the RAM or to preload the I/O buffers.
When the TAP controller is placed in Capture-IR state the two least significant bits of the instruction register are loaded with 01.
When the controller is moved to the Shift-IR state the Instruction Register is placed between TDI and TDO. In this state the desired
instruction is serially loaded through the TDI input (while the previous contents are shifted out at TDO). For all instructions, the
TAP executes newly loaded instructions only when the controller is moved to Update-IR state. The TAP instruction set for this
device is listed in the following table.
JTAG Tap Controller State Diagram
Test Logic Reset
1
0
1
1
1
Run Test Idle
Select DR
Select IR
0
0
0
1
1
1
1
Capture DR
Capture IR
0
0
Shift DR
Shift IR
0
0
1
1
Exit1 DR
Exit1 IR
0
0
Pause DR
Pause IR
0
0
0
0
1
1
Exit2 DR
Exit2 IR
1
1
Update DR
Update IR
1
0
1
0
Instruction Descriptions
BYPASS
When the BYPASS instruction is loaded in the Instruction Register the Bypass Register is placed between TDI and TDO. This
occurs when the TAP controller is moved to the Shift-DR state. This allows the board level scan path to be shortened to facili-
tate testing of other devices in the scan path.
Rev: 1.04c 11/2011
27/36
© 2007, GSI Technology
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
GS8182T08/09/18/36BD-400/375/333/300/250/200/167
SAMPLE/PRELOAD
SAMPLE/PRELOAD is a Standard 1149.1 mandatory public instruction. When the SAMPLE / PRELOAD instruction is
loaded in the Instruction Register, moving the TAP controller into the Capture-DR state loads the data in the RAMs input and
I/O buffers into the Boundary Scan Register. Boundary Scan Register locations are not associated with an input or I/O pin, and
are loaded with the default state identified in the Boundary Scan Chain table at the end of this section of the datasheet. Because
the RAM clock is independent from the TAP Clock (TCK) it is possible for the TAP to attempt to capture the I/O ring contents
while the input buffers are in transition (i.e. in a metastable state). Although allowing the TAP to sample metastable inputs will
not harm the device, repeatable results cannot be expected. RAM input signals must be stabilized for long enough to meet the
TAPs input data capture set-up plus hold time (tTS plus tTH). The RAMs clock inputs need not be paused for any other TAP
operation except capturing the I/O ring contents into the Boundary Scan Register. Moving the controller to Shift-DR state then
places the boundary scan register between the TDI and TDO pins.
EXTEST
EXTEST is an IEEE 1149.1 mandatory public instruction. It is to be executed whenever the instruction register is loaded with
all logic 0s. The EXTEST command does not block or override the RAM’s input pins; therefore, the RAM’s internal state is
still determined by its input pins.
Typically, the Boundary Scan Register is loaded with the desired pattern of data with the SAMPLE/PRELOAD command.
Then the EXTEST command is used to output the Boundary Scan Register’s contents, in parallel, on the RAM’s data output
drivers on the falling edge of TCK when the controller is in the Update-IR state.
Alternately, the Boundary Scan Register may be loaded in parallel using the EXTEST command. When the EXTEST instruc-
tion is selected, the sate of all the RAM’s input and I/O pins, as well as the default values at Scan Register locations not asso-
ciated with a pin, are transferred in parallel into the Boundary Scan Register on the rising edge of TCK in the Capture-DR
state, the RAM’s output pins drive out the value of the Boundary Scan Register location with which each output pin is associ-
ated.
IDCODE
The IDCODE instruction causes the ID ROM to be loaded into the ID register when the controller is in Capture-DR mode and
places the ID register between the TDI and TDO pins in Shift-DR mode. The IDCODE instruction is the default instruction
loaded in at power up and any time the controller is placed in the Test-Logic-Reset state.
SAMPLE-Z
If the SAMPLE-Z instruction is loaded in the instruction register, all RAM outputs are forced to an inactive drive state (high-
Z) and the Boundary Scan Register is connected between TDI and TDO when the TAP controller is moved to the Shift-DR
state.
JTAG TAP Instruction Set Summary
Instruction
EXTEST
Code
000
Description
Notes
1
Places the Boundary Scan Register between TDI and TDO.
Preloads ID Register and places it between TDI and TDO.
IDCODE
001
1, 2
Captures I/O ring contents. Places the Boundary Scan Register between TDI and TDO.
Forces all RAM output drivers to High-Z.
SAMPLE-Z
GSI
010
011
1
1
GSI private instruction.
Rev: 1.04c 11/2011
28/36
© 2007, GSI Technology
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
GS8182T08/09/18/36BD-400/375/333/300/250/200/167
JTAG TAP Instruction Set Summary
SAMPLE/PRELOAD
100
101
110
111
Captures I/O ring contents. Places the Boundary Scan Register between TDI and TDO.
1
1
1
1
GSI
GSI
GSI private instruction.
GSI private instruction.
BYPASS
Places Bypass Register between TDI and TDO.
Notes:
1. Instruction codes expressed in binary, MSB on left, LSB on right.
2. Default instruction automatically loaded at power-up and in test-logic-reset state.
JTAG Port Recommended Operating Conditions and DC Characteristics
Parameter
Symbol
VILJ
Min.
–0.3
Max.
Unit Notes
0.3 * VDD
VDD +0.3
Test Port Input Low Voltage
V
V
1
1
VIHJ
0.7 * VDD
Test Port Input High Voltage
IINHJ
TMS, TCK and TDI Input Leakage Current
TMS, TCK and TDI Input Leakage Current
TDO Output Leakage Current
Test Port Output High Voltage
Test Port Output Low Voltage
Test Port Output CMOS High
Test Port Output CMOS Low
–300
–1
1
100
1
uA
uA
uA
V
2
IINLJ
3
IOLJ
–1
4
VOHJ
VOLJ
VOHJC
VOLJC
VDD – 0.2
—
0.2
—
0.1
5, 6
5, 7
5, 8
5, 9
—
V
VDD – 0.1
V
—
V
Notes:
1. Input Under/overshoot voltage must be –1 V < Vi < V
+1 V not to exceed 2.9 V maximum, with a pulse width not to exceed 20% tTKC.
DDn
2.
V
≤ V ≤ V
ILJ
IN
DDn
3. 0 V ≤ V ≤ V
IN
ILJn
4. Output Disable, V
= 0 to V
DDn
OUT
5. The TDO output driver is served by the V supply.
DD
6.
7.
8.
9.
I
I
I
I
= –2 mA
OHJ
= + 2 mA
OLJ
= –100 uA
= +100 uA
OHJC
OLJC
Rev: 1.04c 11/2011
29/36
© 2007, GSI Technology
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
GS8182T08/09/18/36BD-400/375/333/300/250/200/167
JTAG Port AC Test Conditions
Parameter
Input high level
Input low level
Conditions
JTAG Port AC Test Load
VDD – 0.2 V
TDO
0.2 V
1 V/ns
VDD/2
*
Input slew rate
50Ω
30pF
Input reference level
V
/2
DD
V
DD/2
Output reference level
* Distributed Test Jig Capacitance
Notes:
1. Include scope and jig capacitance.
2. Test conditions as shown unless otherwise noted.
JTAG Port Timing Diagram
tTKC
tTKH
tTKL
TCK
tTH
tTH
tTS
tTS
TDI
TMS
tTKQ
TDO
tTH
tTS
Parallel SRAM input
JTAG Port AC Electrical Characteristics
Parameter
Symbol
tTKC
tTKQ
tTKH
tTKL
tTS
Min
Max
—
Unit
ns
TCK Cycle Time
50
—
20
20
10
10
TCK Low to TDO Valid
TCK High Pulse Width
TCK Low Pulse Width
TDI & TMS Set Up Time
TDI & TMS Hold Time
20
—
ns
ns
—
ns
—
ns
tTH
—
ns
Rev: 1.04c 11/2011
30/36
© 2007, GSI Technology
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
GS8182T08/09/18/36BD-400/375/333/300/250/200/167
Package Dimensions—165-Bump FPBGA (Package D)
A1 CORNER
TOP VIEW
BOTTOM VIEW
A1 CORNER
M
M
Ø0.10
C
Ø0.25 C A B
Ø0.40~0.60 (165x)
1
2 3 4 5 6 7 8 9 10 11
11 10 9 8
7 6 5 4 3 2 1
A
B
C
D
E
F
A
B
C
D
E
F
G
H
J
G
H
J
K
L
K
L
M
N
P
R
M
N
P
R
A
1.0
10.0
1.0
13±0.05
B
0.20(4x)
SEATING PLANE
C
Rev: 1.04c 11/2011
31/36
© 2007, GSI Technology
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
GS8182T08/09/18/36BD-400/375/333/300/250/200/167
Ordering Information—GSI SigmaDDR-II SRAM
2
Org
Part Number1
Type
Package
Speed (MHz)
T
A
2M x 8
2M x 8
2M x 8
2M x 8
2M x 8
2M x 8
2M x 8
2M x 8
2M x 8
2M x 8
2M x 8
2M x 8
2M x 8
2M x 8
2M x 9
2M x 9
2M x 9
2M x 9
2M x 9
2M x 9
2M x 9
2M x 9
2M x 9
2M x 9
2M x 9
2M x 9
2M x 9
2M x 9
1M x 18
1M x 18
1M x 18
1M x 18
GS8182T08BD-400
GS8182T08BD-375
GS8182T08BD-333
GS8182T08BD-300
GS8182T08BD-250
GS8182T08BD-200
GS8182T08BD-167
GS8182T08BD-400I
GS8182T08BD-375I
GS8182T08BD-333I
GS8182T08BD-300I
GS8182T08BD-250I
GS8182T08BD-200I
GS8182T08BD-167I
GS8182T09BD-400
GS8182T09BD-375
GS8182T09BD-333
GS8182T09BD-300
GS8182T09BD-250
GS8182T09BD-200
GS8182T09BD-167
GS8182T09BD-400I
GS8182T09BD-375I
GS8182T09BD-333I
GS8182T09BD-300I
GS8182T09BD-250I
GS8182T09BD-200I
GS8182T09BD-167I
GS8182T18BD-400
GS8182T18BD-375
GS8182T18BD-333
GS8182T18BD-300
SigmaDDR-II B2 SRAM
SigmaDDR-II B2 SRAM
SigmaDDR-II B2 SRAM
SigmaDDR-II B2 SRAM
SigmaDDR-II B2 SRAM
SigmaDDR-II B2 SRAM
SigmaDDR-II B2 SRAM
SigmaDDR-II B2 SRAM
SigmaDDR-II B2 SRAM
SigmaDDR-II B2 SRAM
SigmaDDR-II B2 SRAM
SigmaDDR-II B2 SRAM
SigmaDDR-II B2 SRAM
SigmaDDR-II B2 SRAM
SigmaDDR-II B2 SRAM
SigmaDDR-II B2 SRAM
SigmaDDR-II B2 SRAM
SigmaDDR-II B2 SRAM
SigmaDDR-II B2 SRAM
SigmaDDR-II B2 SRAM
SigmaDDR-II B2 SRAM
SigmaDDR-II B2 SRAM
SigmaDDR-II B2 SRAM
SigmaDDR-II B2 SRAM
SigmaDDR-II B2 SRAM
SigmaDDR-II B2 SRAM
SigmaDDR-II B2 SRAM
SigmaDDR-II B2 SRAM
SigmaDDR-II B2 SRAM
SigmaDDR-II B2 SRAM
SigmaDDR-II B2 SRAM
SigmaDDR-II B2 SRAM
165-bump BGA
165-bump BGA
165-bump BGA
165-bump BGA
165-bump BGA
165-bump BGA
165-bump BGA
165-bump BGA
165-bump BGA
165-bump BGA
165-bump BGA
165-bump BGA
165-bump BGA
165-bump BGA
165-bump BGA
165-bump BGA
165-bump BGA
165-bump BGA
165-bump BGA
165-bump BGA
165-bump BGA
165-bump BGA
165-bump BGA
165-bump BGA
165-bump BGA
165-bump BGA
165-bump BGA
165-bump BGA
165-bump BGA
165-bump BGA
165-bump BGA
165-bump BGA
400
375
333
300
250
200
167
400
375
333
300
250
200
167
400
375
333
300
250
200
167
400
375
333
300
250
200
167
400
375
333
300
C
C
C
C
C
C
C
I
I
I
I
I
I
I
C
C
C
C
C
C
C
I
I
I
I
I
I
I
C
C
C
C
Notes:
1. For Tape and Reel add the character “T” to the end of the part number. Example: GS818T36BD-300T.
2. C = Commercial Temperature Range. I = Industrial Temperature Range.
Rev: 1.04c 11/2011
32/36
© 2007, GSI Technology
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
GS8182T08/09/18/36BD-400/375/333/300/250/200/167
Ordering Information—GSI SigmaDDR-II SRAM
2
Org
Part Number1
Type
Package
Speed (MHz)
T
A
1M x 18
1M x 18
1M x 18
1M x 18
1M x 18
1M x 18
1M x 18
1M x 18
1M x 18
1M x 18
512K x 36
512K x 36
512K x 36
512K x 36
512K x 36
512K x 36
512K x 36
512K x 36
512K x 36
512K x 36
512K x 36
512K x 36
512K x 36
512K x 36
2M x 8
GS8182T18BD-250
GS8182T18BD-200
GS8182T18BD-167
GS8182T18BD-400I
GS8182T18BD-375I
GS8182T18BD-333I
GS8182T18BD-300I
GS8182T18BD-250I
GS8182T18BD-200I
GS8182T18BD-167I
GS8182T36BD-400
GS8182T36BD-375
GS8182T36BD-333
GS8182T36BD-300
GS8182T36BD-250
GS8182T36BD-200
GS8182T36BD-167
GS8182T36BD-400I
GS8182T36BD-375I
GS8182T36BD-333I
GS8182T36BD-300I
GS8182T36BD-250I
GS8182T36BD-200I
GS8182T36BD-167I
GS8182T08BGD-400
GS8182T08BGD-375
GS8182T08BGD-333
GS8182T08BGD-300
GS8182T08BGD-250
GS8182T08BGD-200
GS8182T08BGD-167
GS8182T08BGD-400I
GS8182T08BGD-375I
SigmaDDR-II B2 SRAM
SigmaDDR-II B2 SRAM
SigmaDDR-II B2 SRAM
SigmaDDR-II B2 SRAM
SigmaDDR-II B2 SRAM
SigmaDDR-II B2 SRAM
SigmaDDR-II B2 SRAM
SigmaDDR-II B2 SRAM
SigmaDDR-II B2 SRAM
SigmaDDR-II B2 SRAM
SigmaDDR-II B2 SRAM
SigmaDDR-II B2 SRAM
SigmaDDR-II B2 SRAM
SigmaDDR-II B2 SRAM
SigmaDDR-II B2 SRAM
SigmaDDR-II B2 SRAM
SigmaDDR-II B2 SRAM
SigmaDDR-II B2 SRAM
SigmaDDR-II B2 SRAM
SigmaDDR-II B2 SRAM
SigmaDDR-II B2 SRAM
SigmaDDR-II B2 SRAM
SigmaDDR-II B2 SRAM
SigmaDDR-II B2 SRAM
SigmaDDR-II B2 SRAM
SigmaDDR-II B2 SRAM
SigmaDDR-II B2 SRAM
SigmaDDR-II B2 SRAM
SigmaDDR-II B2 SRAM
SigmaDDR-II B2 SRAM
SigmaDDR-II B2 SRAM
SigmaDDR-II B2 SRAM
SigmaDDR-II B2 SRAM
165-bump BGA
165-bump BGA
250
200
167
400
375
333
300
250
200
167
400
375
333
300
250
200
167
400
375
333
300
250
200
167
400
375
333
300
250
200
167
400
375
C
C
C
I
165-bump BGA
165-bump BGA
165-bump BGA
I
165-bump BGA
I
165-bump BGA
I
165-bump BGA
I
165-bump BGA
I
165-bump BGA
I
165-bump BGA
C
C
C
C
C
C
C
I
165-bump BGA
165-bump BGA
165-bump BGA
165-bump BGA
165-bump BGA
165-bump BGA
165-bump BGA
165-bump BGA
I
165-bump BGA
I
165-bump BGA
I
165-bump BGA
I
165-bump BGA
I
165-bump BGA
I
RoHS-compliant 165-bump BGA
RoHS-compliant 165-bump BGA
RoHS-compliant 165-bump BGA
RoHS-compliant 165-bump BGA
RoHS-compliant 165-bump BGA
RoHS-compliant 165-bump BGA
RoHS-compliant 165-bump BGA
RoHS-compliant 165-bump BGA
RoHS-compliant 165-bump BGA
C
C
C
C
C
C
C
I
2M x 8
2M x 8
2M x 8
2M x 8
2M x 8
2M x 8
2M x 8
2M x 8
I
Notes:
1. For Tape and Reel add the character “T” to the end of the part number. Example: GS818T36BD-300T.
2. C = Commercial Temperature Range. I = Industrial Temperature Range.
Rev: 1.04c 11/2011
33/36
© 2007, GSI Technology
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
GS8182T08/09/18/36BD-400/375/333/300/250/200/167
Ordering Information—GSI SigmaDDR-II SRAM
2
Org
Part Number1
Type
Package
Speed (MHz)
T
A
2M x 8
2M x 8
2M x 8
2M x 8
2M x 8
2M x 9
2M x 9
2M x 9
2M x 9
2M x 9
2M x 9
2M x 9
2M x 9
2M x 9
2M x 9
2M x 9
2M x 9
2M x 9
2M x 9
1M x 18
1M x 18
1M x 18
1M x 18
1M x 18
1M x 18
1M x 18
1M x 18
1M x 18
1M x 18
1M x 18
1M x 18
1M x 18
1M x 18
GS8182T08BGD-333I
GS8182T08BGD-300I
GS8182T08BGD-250I
GS8182T08BGD-200I
GS8182T08BGD-167I
GS8182T09BGD-400
GS8182T09BGD-375
GS8182T09BGD-333
GS8182T09BGD-300
GS8182T09BGD-250
GS8182T09BGD-200
GS8182T09BGD-167
GS8182T09BGD-400I
GS8182T09BGD-375I
GS8182T09BGD-333I
GS8182T09BGD-300I
GS8182T09BGD-250I
GS8182T09BGD-200I
GS8182T09BGD-167I
GS8182T18BGD-400
GS8182T18BGD-375
GS8182T18BGD-333
GS8182T18BGD-300
GS8182T18BGD-250
GS8182T18BGD-200
GS8182T18BGD-167
GS8182T18BGD-400I
GS8182T18BGD-375I
GS8182T18BGD-333I
GS8182T18BGD-300I
GS8182T18BGD-250I
GS8182T18BGD-200I
GS8182T18BGD-167I
SigmaDDR-II B2 SRAM
SigmaDDR-II B2 SRAM
SigmaDDR-II B2 SRAM
SigmaDDR-II B2 SRAM
SigmaDDR-II B2 SRAM
SigmaDDR-II B2 SRAM
SigmaDDR-II B2 SRAM
SigmaDDR-II B2 SRAM
SigmaDDR-II B2 SRAM
SigmaDDR-II B2 SRAM
SigmaDDR-II B2 SRAM
SigmaDDR-II B2 SRAM
SigmaDDR-II B2 SRAM
SigmaDDR-II B2 SRAM
SigmaDDR-II B2 SRAM
SigmaDDR-II B2 SRAM
SigmaDDR-II B2 SRAM
SigmaDDR-II B2 SRAM
SigmaDDR-II B2 SRAM
SigmaDDR-II B2 SRAM
SigmaDDR-II B2 SRAM
SigmaDDR-II B2 SRAM
SigmaDDR-II B2 SRAM
SigmaDDR-II B2 SRAM
SigmaDDR-II B2 SRAM
SigmaDDR-II B2 SRAM
SigmaDDR-II B2 SRAM
SigmaDDR-II B2 SRAM
SigmaDDR-II B2 SRAM
SigmaDDR-II B2 SRAM
SigmaDDR-II B2 SRAM
SigmaDDR-II B2 SRAM
SigmaDDR-II B2 SRAM
RoHS-compliant 165-bump BGA
RoHS-compliant 165-bump BGA
RoHS-compliant 165-bump BGA
RoHS-compliant 165-bump BGA
RoHS-compliant 165-bump BGA
RoHS-compliant 165-bump BGA
RoHS-compliant 165-bump BGA
RoHS-compliant 165-bump BGA
RoHS-compliant 165-bump BGA
RoHS-compliant 165-bump BGA
RoHS-compliant 165-bump BGA
RoHS-compliant 165-bump BGA
RoHS-compliant 165-bump BGA
RoHS-compliant 165-bump BGA
RoHS-compliant 165-bump BGA
RoHS-compliant 165-bump BGA
RoHS-compliant 165-bump BGA
RoHS-compliant 165-bump BGA
RoHS-compliant 165-bump BGA
RoHS-compliant 165-bump BGA
RoHS-compliant 165-bump BGA
RoHS-compliant 165-bump BGA
RoHS-compliant 165-bump BGA
RoHS-compliant 165-bump BGA
RoHS-compliant 165-bump BGA
RoHS-compliant 165-bump BGA
RoHS-compliant 165-bump BGA
RoHS-compliant 165-bump BGA
RoHS-compliant 165-bump BGA
RoHS-compliant 165-bump BGA
RoHS-compliant 165-bump BGA
RoHS-compliant 165-bump BGA
RoHS-compliant 165-bump BGA
333
300
250
200
167
400
375
333
300
250
200
167
400
375
333
300
250
200
167
400
375
333
300
250
200
167
400
375
333
300
250
200
167
I
I
I
I
I
C
C
C
C
C
C
C
I
I
I
I
I
I
I
C
C
C
C
C
C
C
I
I
I
I
I
I
I
Notes:
1. For Tape and Reel add the character “T” to the end of the part number. Example: GS818T36BD-300T.
2. C = Commercial Temperature Range. I = Industrial Temperature Range.
Rev: 1.04c 11/2011
34/36
© 2007, GSI Technology
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
GS8182T08/09/18/36BD-400/375/333/300/250/200/167
Ordering Information—GSI SigmaDDR-II SRAM
2
Org
Part Number1
Type
Package
Speed (MHz)
T
A
512K x 36
512K x 36
512K x 36
512K x 36
512K x 36
512K x 36
512K x 36
512K x 36
512K x 36
512K x 36
512K x 36
512K x 36
512K x 36
512K x 36
Notes:
GS8182T36BGD-400
GS8182T36BGD-375
GS8182T36BGD-333
GS8182T36BGD-300
GS8182T36BGD-250
GS8182T36BGD-200
GS8182T36BGD-167
GS8182T36BGD-400I
GS8182T36BGD-375I
GS8182T36BGD-333I
GS8182T36BGD-300I
GS8182T36BGD-250I
GS8182T36BGD-200I
GS8182T36BGD-167I
SigmaDDR-II B2 SRAM
SigmaDDR-II B2 SRAM
SigmaDDR-II B2 SRAM
SigmaDDR-II B2 SRAM
SigmaDDR-II B2 SRAM
SigmaDDR-II B2 SRAM
SigmaDDR-II B2 SRAM
SigmaDDR-II B2 SRAM
SigmaDDR-II B2 SRAM
SigmaDDR-II B2 SRAM
SigmaDDR-II B2 SRAM
SigmaDDR-II B2 SRAM
SigmaDDR-II B2 SRAM
SigmaDDR-II B2 SRAM
RoHS-compliant 165-bump BGA
RoHS-compliant 165-bump BGA
RoHS-compliant 165-bump BGA
RoHS-compliant 165-bump BGA
RoHS-compliant 165-bump BGA
RoHS-compliant 165-bump BGA
RoHS-compliant 165-bump BGA
RoHS-compliant 165-bump BGA
RoHS-compliant 165-bump BGA
RoHS-compliant 165-bump BGA
RoHS-compliant 165-bump BGA
RoHS-compliant 165-bump BGA
RoHS-compliant 165-bump BGA
RoHS-compliant 165-bump BGA
400
375
333
300
250
200
167
400
375
333
300
250
200
167
C
C
C
C
C
C
C
I
I
I
I
I
I
I
1. For Tape and Reel add the character “T” to the end of the part number. Example: GS818T36BD-300T.
2. C = Commercial Temperature Range. I = Industrial Temperature Range.
Rev: 1.04c 11/2011
35/36
© 2007, GSI Technology
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
GS8182T08/09/18/36BD-400/375/333/300/250/200/167
Revision History
Types of Changes
Format or Content
Rev. Code: Old; New
Revisions
• Creation of new datasheet
GS8182TxxB_r1
Format
(Rev1.00b: erroneous green part numbers corrected)
• Updated AC Electrical Characteristics table
GS8182TxxB_r1_01
Format
• Revised Example Four Bank Depth Expansion Schematic
• Updated JTAG Port AC Test Conditions
• Updated 165 BGA Package Drawing
GS8182TxxB_r1_02
GS8182TxxB_r1_03
Content
Content
• (Rev1.02a: Added Operating Currents numbers)
• Added 400 & 375 MHz speed bins
• Removed “Preliminary” banner to indicate MP status
• (Rev1.04a: Updated power up)
GS8182TxxB_r1_04
Content
• (Rev1.04b: removed CQ reference from SAMPLE-Z section in
JTAG Tap Instruction Set Summary)
• (Rev1.04c: Editorial updates)
Rev: 1.04c 11/2011
36/36
© 2007, GSI Technology
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
相关型号:
GS8182T08BGD-250IT
DDR SRAM, 2MX8, 0.45ns, CMOS, PBGA165, 13 X 15 MM, 1 MM PITCH, ROHS COMPLIANT, FPBGA-165
GSI
GS8182T08BGD-333
DDR SRAM, 2MX8, 0.45ns, CMOS, PBGA165, 13 X 15 MM, 1 MM PITCH, ROHS COMPLIANT, FPBGA-165
GSI
GS8182T08BGD-333I
DDR SRAM, 2MX8, 0.45ns, CMOS, PBGA165, 13 X 15 MM, 1 MM PITCH, ROHS COMPLIANT, FPBGA-165
GSI
GS8182T08BGD-333IT
DDR SRAM, 2MX8, 0.45ns, CMOS, PBGA165, 13 X 15 MM, 1 MM PITCH, ROHS COMPLIANT, FPBGA-165
GSI
GS8182T08BGD-333T
DDR SRAM, 2MX8, 0.45ns, CMOS, PBGA165, 13 X 15 MM, 1 MM PITCH, ROHS COMPLIANT, FPBGA-165
GSI
©2020 ICPDF网 联系我们和版权申明