GS2988-INTE3 [GENNUM]
Dual-Slew-Rate, Cable Driver with 3Gb/s Capability;
| 型号： | GS2988-INTE3 |
| 厂家： | 
GENNUM CORPORATION |
| 描述： | Dual-Slew-Rate, Cable Driver with 3Gb/s Capability |
| 文件： | 总17页 (文件大小：683K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
GS2988 Dual-Slew-Rate, Cable Driver with 3Gb/s Capability
Features
Description
•
SMPTE 424M, SMPTE 292M and SMPTE 259M
The GS2988 is a high-speed BiCMOS integrated circuit
designed to drive one to two 75Ω coaxial cables.
compliant
•
•
•
Supports DVB-ASI at 270Mb/s
Supports data rates from 270Mb/s to 2.97Gb/s
Wide common-mode range input buffer
The GS2988 may drive data rates up to 2.97Gb/s and
provides two selectable slew rates in order to achieve
compliance to SMPTE 424M, SMPTE 292M and SMPTE
259M.
100mV sensitivity
The GS2988 accepts industry-standard differential input
levels including LVPECL and CML.
supports DC-coupling to industry-standard
differential logic
Input trace equalization compensates for up to 10 inches of
FR4 trace loss while in HD and 3G modes. This feature can
be disabled using the EQ_EN pin.
on-chip 100Ω differential data input termination
•
•
Input signal trace equalization
The DISABLE pin powers-down the entire device.
Differential coaxial-cable-driving output
The GS2988 features adjustable output swing using an
external bias resistor. The single-ended output swing is
adjustable from 500mVpp to 1800mVpp.
selectable slew rates
adjustable output swing from 500mVpp to
1800mVpp
An output signal presence function, the OSP pin, indicates
whether an active signal is present at the output of the
GS2988.
DISABLE control
•
•
•
•
•
•
Robust output signal presence function
Excellent output eye quality
The GS2988 can be powered from either a 3.3V or a 2.5V
supply. Power consumption is typically 110mW using a
2.5V power supply.
Power supply operation at 3.3V or 2.5V
110mW power consumption (2.5V supply)
Operating temperature range: -40°C to +85°C
Small footprint QFN package (4mm x 4mm)
The GS2988 is Pb-free, and the encapsulation compound
does not contain halogenated flame retardant.
This component and all homogeneous subcomponents are
RoHS compliant.
Drop-in compatible to the GS2978
•
Pb-free and RoHS compliant
Applications
•
SMPTE 424M, SMPTE 292M and SMPTE 259M coaxial
cable serial digital interfaces
GS2988 Dual-Slew-Rate, Cable Driver with 3Gb/s
Capability
Data Sheet
1 of 17
www.gennum.com
52131 - 4
December 2010
EQ_EN
SD/HD
DISABLE
DDI
DDI
SDO
SDO
Slew Rate
Control
Equalizer
Output
Signal
OSP
Presence
Band Gap Reference
&
Output Control
RSET
Functional Block Diagram
Revision History
Version
ECR
PCN
Date
Changes and/or Modifications
4
3
155552
155359
–
–
December 2010
November 2010
Corrected the Marking Diagram.
Clarified the functionality of the EQ_EN pin in Table
1-1: Pin Descriptions and throughout the document.
2
1
0
155070
153602
153455
–
–
–
October 2010
February 2010
January 2010
Updated Typical Application Circuit.
Converted document to Data Sheet.
Converted document to Preliminary Data Sheet.
Changed Additive jitter numbers in Table 2-2: AC
Electrical Characteristics.
B
152690
151623
–
–
October 2009
April 2009
Updates to Section 2. Electrical Characteristics.
Corrections to Section 3. Input/Output Circuits.
A
New document.
GS2988 Dual-Slew-Rate, Cable Driver with 3Gb/s
2 of 17
Capability
Data Sheet
52131 - 4
December 2010
Contents
Features.................................................................................................................................................................1
Applications.........................................................................................................................................................1
Description...........................................................................................................................................................1
Revision History .................................................................................................................................................2
1. Pin Out...............................................................................................................................................................4
1.1 Pin Assignment ..................................................................................................................................4
1.2 Pin Descriptions ................................................................................................................................4
2. Electrical Characteristics ............................................................................................................................5
2.1 Absolute Maximum Ratings ..........................................................................................................5
2.2 DC Electrical Characteristics ........................................................................................................6
2.3 AC Electrical Characteristics ........................................................................................................7
3. Input/Output Circuits ..................................................................................................................................8
4. Detailed Description.....................................................................................................................................9
4.1 Serial Data Input ...............................................................................................................................9
4.2 Input Trace-equalization ................................................................................................................9
4.3 Serial Data Output ............................................................................................................................9
4.3.1 Slew Rate Selection (Rise/Fall Time Requirement)....................................................9
4.4 Output Disable ................................................................................................................................ 10
4.5 Output Signal Presence Indicator (OSP) ................................................................................. 10
4.6 Output Amplitude (RSET) ........................................................................................................... 10
4.7 Output Return Loss Measurement ........................................................................................... 12
5. Application Information .......................................................................................................................... 13
5.1 PCB Layout ....................................................................................................................................... 13
5.2 Typical Application Circuit ........................................................................................................ 13
6. Package & Ordering Information .......................................................................................................... 14
6.1 Package Dimensions ..................................................................................................................... 14
6.2 Recommended PCB Footprint ................................................................................................... 15
6.3 Packaging Data ............................................................................................................................... 15
6.4 Solder Reflow Profiles .................................................................................................................. 16
6.5 Marking Diagram ........................................................................................................................... 16
6.6 Ordering Information ................................................................................................................... 17
GS2988 Dual-Slew-Rate, Cable Driver with 3Gb/s
3 of 17
Capability
Data Sheet
52131 - 4
December 2010
1. Pin Out
1.1 Pin Assignment
16
15
14
13
12
11
10
9
1
DDI
SDO
GS2988
16-pin QFN
(top view)
2
DDI
SDO
3
SD/HD
VEE
4
VCC
RSET
5
6
7
8
Ground Pad
(bottom of package)
Figure 1-1: 16-Pin QFN
1.2 Pin Descriptions
Table 1-1: Pin Descriptions
Pin Number
Name
Type
Description
1, 2
3
DDI, DDI
VEE
Input
Serial data differential input.
Power
Most negative power supply connection for the input buffer and core.
Connect to GND.
4
RSET
N/C
Input
External output amplitude control resistor connection.
5, 7, 8, 13, 15
−
No Connect.
These pins are not connected internally.
6
9
DISABLE
Input
Control signal input.
When set LOW, the entire device is powered-down.
When set HIGH, the SDO/SDO pins will output a serial data signal.
NOTE: if this pin is left floating, the serial data output will be enabled.
VCC
Power
Most positive power supply connection.
Connect to 3.3V or 2.5V.
GS2988 Dual-Slew-Rate, Cable Driver with 3Gb/s
4 of 17
Capability
Data Sheet
52131 - 4
December 2010
Table 1-1: Pin Descriptions
Pin Number
Name
Type
Description
10
SD/HD
Input
Control signal input.
When set HIGH, the serial data output will meet the SMPTE 259M rise/fall time
specification.
When set LOW, the serial output will meet the SMPTE 292M and SMPTE 424M rise/fall
time specification.
NOTE: if this pin is left floating, the serial data output will meet the SMPTE 259M
rise/fall time specification.
11, 12
14
SDO/
SDO
Output
Output
Serial data differential output.
OSP
Output signal presence status signal output.
Signal levels are LVCMOS/LVTTL compatible.
Indicates presence of a valid output signal.
When the OSP pin is LOW, a good input signal has been detected within the output
stage pre-driver.
When this pin is HIGH, the output signal is invalid at the output of the pre-driver.
16
EQ_EN
Input
Control signal input.
When set LOW, trace-equalization is turned ON.
When set HIGH, trace-equalization is turned OFF.
NOTE 1: if this pin is left floating, trace-equalization is turned OFF.
NOTE 2: this pin must be pulled HIGH or left floating for operation in SD mode.
–
Center Pad
Power
Connect to most negative power supply plane following the recommendations in
Recommended PCB Footprint on page 15.
2. Electrical Characteristics
2.1 Absolute Maximum Ratings
Parameter
Value
Supply Voltage
-0.5V to 3.6 V
2.5kV
DC
Input ESD Voltage
Storage Temperature Range
-50°C < T < 125°C
s
Input Voltage Range (any input)
-0.3 to (V +0.3)V
CC
Operating Temperature Range
Solder Reflow Temperature
-40°C to +85°C
260°C
NOTE: Absolute Maximum Ratings are those values beyond which damage to the device may
occur. Functional operation under these conditions or at any other condition beyond those
indicated in the AC/DC Electrical Characteristic sections is not implied.
GS2988 Dual-Slew-Rate, Cable Driver with 3Gb/s
5 of 17
Capability
Data Sheet
52131 - 4
December 2010
2.2 DC Electrical Characteristics
Table 2-1: DC Electrical Characteristics
V
= 3.3V 5ꢀ or 2.5V 5ꢀ; T = -40°C to +85°C, unless otherwise shown
A
CC
Parameter
Symbol Conditions
Min
Typ
Max
Units
Notes
Supply Voltage
V
3.3V Typical
3.135
3.3
2.5
110
3
3.465
2.625
130
5
V
–
–
1
1
1
1
1
1
1
–
CC
2.5V Typical
2.375
V
Power Consumption
(2.5V)
P
SDO/SDO enabled
SDO/SDO disabled
SDO/SDO enabled
SDO/SDO disabled
VCC = 3.3V
–
–
–
–
–
–
–
–
mW
mW
mW
mW
mA
mA
mA
V
D
Power Consumption
(3.3V)
155
4
183
6
Supply Current
I
47
44
1
53
S
VCC = 2.5V
50
Power-down
1.8
–
Output Voltage
Input Voltage
V
Common mode
V
- V
CMOUT
TERM OUT
V
Common mode
1.4 + ΔV /2
–
–
–
–
V
- ΔV /2
V
V
–
–
–
–
CMIN
DDI
CC
DDI
SD/HD, DISABLE,
EQ_EN Input
V
I
I
<= 150μA
<= 150μA
1.7
–
–
0.8
–
IH
IH
IL
V
V
IL
OSP Drive Strength
–
–
2
mA
NOTES:
1. Power consumed in GS2988 only. Termination resistors draw extra current.
GS2988 Dual-Slew-Rate, Cable Driver with 3Gb/s
6 of 17
Capability
Data Sheet
52131 - 4
December 2010
2.3 AC Electrical Characteristics
Table 2-2: AC Electrical Characteristics
V
= 3.3V 5ꢀ or 2.5V 5ꢀ; T = -40°C to +85°C, unless otherwise shown
A
CC
Parameter
Symbol
Conditions
–
Min
.27
–
Typ
–
Max
2.97
–
Units
Notes
Serial input data rate
Additive jitter
DR
Gb/s
1
2
2
2
3
3
–
SDO
–
–
–
2.97Gb/s
10
10
30
–
ps
ps
ps
p-p
p-p
p-p
1.485Gb/s
270Mb/s
–
–
–
–
Rise/Fall time
t , t
SD/HD=0
SD/HD=1
HD/3G modes only
–
135
800
35
ps
r
f
f
t , t
400
–
–
ps
ps
r
Mismatch in rise/fall time
Duty cycle distortion
Ut , Ut
–
r
f
–
–
SD/HD=0, 2.97Gb/s
SD/HD=0, 1.485Gb/s
SD/HD=1
–
–
–
–
14
20
50
10
–
ps
ps
ps
ꢀ
dB
dB
4, 5
4, 5
4, 5
4
–
–
–
Overshoot
–
SD/HD=0,
–
–
Output Return Loss
ORL
5 MHz – 1.485GHz
1.485GHz – 2.97GHz
17
13
750
19
15
800
6
–
6
Output Voltage Swing
Input Voltage Swing
V
R
= 750Ω
850
mV
4
OUT
SET
p-p
UV
Guaranteed
100
–
250
mV
–
DDI
p-pd
functional.
Guaranteed to meet all
published
250
2200
mV
–
p-pd
specifications.
Output Enable Delay
Output Disable Delay
NOTES:
–
–
–
–
–
–
–
–
100
80
ns
ns
–
–
1. The input coupling capacitor must be set accordingly for lower data rates.
2. Turning on input trace equalization will reduce jitter in most applications.
3. Rise/Fall time measured between 20% and 80%.
4. Single-ended into 75Ω external load.
5. Calculated as the actual positive bit-width compared to the expected positive bit-width using a 1010 pattern.
6. ORL depends on board design. The GS2988 achieves this specification on Gennum's evaluation boards.
GS2988 Dual-Slew-Rate, Cable Driver with 3Gb/s
7 of 17
Capability
Data Sheet
52131 - 4
December 2010
3. Input/Output Circuits
V
V
CC
CC
DDI
DDI
EQ RC*
SDO
SDO
V
cc
V
CC
I
REF
5k
50
50
10k
*RC Network
700p
for Trace Equalization
Figure 3-1: Differential Input Stage (DDI/DDI)
Figure 3-2: Differential Output Stage (SDO/SDO)
V
CC
Pull-up
80μA typical
(50-150μA)
IN
VREF
Figure 3-3: Control Input (DISABLE, SD/HD, EQ_EN)
GS2988 Dual-Slew-Rate, Cable Driver with 3Gb/s
8 of 17
Capability
Data Sheet
52131 - 4
December 2010
4. Detailed Description
4.1 Serial Data Input
The GS2988 features a differential input buffer with on-chip 100Ω differential
termination.
The serial data input signal is connected to the DDI and DDI input pins of the device.
Input signals can be single-ended or differential, DC or AC-coupled.
The serial data input buffer is capable of operation with any binary coded signal that
meets the input signal level requirements, in the range of 270Mb/s to at least 2.97Gb/s.
The input circuit is self-biasing to allow for simple AC or DC-coupling of input signals to
the device.
4.2 Input Trace-equalization
The GS2988 features fixed trace-equalization to compensate for PCB trace dielectric
losses.
NOTE: This feature is not available in SD mode, and therefore trace-equalization must
be disabled when operating in this mode.
The trace-equalization has two settings, OFF and ON. ON invokes a typical 3dB gain
value at 1.5GHz. This value is optimized for compensating the high-frequency losses
associated with approximately 10 inches of 5-mil stripline in FR4 material.
Table 4-1: Input Trace-Equalization
EQ_EN
Function
0
1
Typical 3dB Trace Equalization
Trace Equalization OFF
Floating
Trace Equalization OFF
4.3 Serial Data Output
The GS2988 features a current-mode differential output driver capable of driving up to
1800mVpp single-ended into a 1m length of 75Ω cable terminated at both ends.
The output signal amplitude or swing is user configurable using an external RSET
resistor.
The SDO/SDO pin of the device provide the serial data outputs.
4.3.1 Slew Rate Selection (Rise/Fall Time Requirement)
The GS2988 supports two user-selectable output slew rates.
Control of the slew rate is determined by the setting of the SD/HD input pin.
GS2988 Dual-Slew-Rate, Cable Driver with 3Gb/s
9 of 17
Capability
Data Sheet
52131 - 4
December 2010
Table 4-2: Slew Rate Selection
SD/HD
Rise/Fall Time
0
1
SMPTE 424M & 292M compliant
SMPTE 259M compliant
Floating
SMPTE 259M compliant
4.4 Output Disable
The GS2988 supports an output disable function for the serial data differential output.
Control of this function is determined by the setting of the DISABLE control pin.
The serial output disable (DISABLE), disables power to the entire device. When asserted
LOW, the SDO/SDO output driver is powered-down.
Table 4-3: Output Disable
DISABLE
SDO/SDO
0
1
All Chip Power Down
Operational
Floating
Operational
4.5 Output Signal Presence Indicator (OSP)
The GS2988 supports an output signal presence indicator function.
The output signal presence pin (OSP) is an active-low output that indicates when a valid
output signal has been detected at the pre-driver output.
The output signal presence function measures signal-edge energy to indicate that the
pre-driver to the serial data outputs is toggling.
Table 4-4: Output Signal Presence Indicator
Pre-Driver Output
OSP Pin
Valid signal present
0
1
No valid signal present
4.6 Output Amplitude (RSET)
The output amplitude of the GS2988 can be adjusted by changing the value of the RSET
resistor as shown in Figure 4-1. For an 800mVp-p output with a nominal ±7% tolerance,
a value of 750Ω is required. A ±1% SMT resistor should be used.
GS2988 Dual-Slew-Rate, Cable Driver with 3Gb/s
10 of 17
Capability
Data Sheet
52131 - 4
December 2010
The RSET resistor is part of an internal DC feedback loop in the GS2988. The resistor
should be placed as close as possible to the RSET pin, and connected directly to the VCC
plane (traces/wires may cause instability). In addition, the PCB capacitance should be
minimized at this node by removing the PCB groundplane beneath the RSET resistor and
the RSET pin.
NOTE: Care should be taken when considering layout of the RSET resistor. Please refer
to Section 5.1 for more details.
2.0
1.75
1.5
1.25
1.0
0.75
0.5
0.25
0.250
0.500
0.750
1.0
1.5
1.25
RSET (kΩ)
Figure 4-1: VOUT vs. RSET
In order to determine the best starting value for Rset, the following formula should be
used:
Rset = 8*(Rtrm/VoutppSE)
Where VoutppSE is in Volts, and both resistances are in Ω.
Rtrm is the value of the termination resistors, which should be equal to the
characteristic impedance of the cable, and is typically 75Ω.
The cable must be short (≤1m), and terminated at both ends for the formula to be valid.
Example: For a 75Ω cable, Rtrm = 75Ω (at both ends), VoutppSE = 800mV
Rset = 8*(75/0.8) = 750Ω
GS2988 Dual-Slew-Rate, Cable Driver with 3Gb/s
11 of 17
Capability
Data Sheet
52131 - 4
December 2010
This formula is not valid for long, unterminated, or improperly terminated cables.
This formula should be considered as a starting point, and actual swing values may vary
based on layout. Also, for large output swings (>1040mV), smaller Rset values may be
required in order to achieve the desired output swing level at HD and 3G data rates.
Table 4-5: Typical RSET Values
Output Swing (mV)
RSET (Ω)
1800*
800
332
750
500
1210
*NOTE: In order to generate output swings greater than 1040mV, VCC_TERM must be
connected to a 5V supply.
4.7 Output Return Loss Measurement
The GS2988 has a feature which allows users to measure ORL reliably while the device
is still powered. The device can be put into a BALANCE mode which prevents the
outputs from toggling while the device is powered on, allowing the ORL to be measured
while the device is still powered.
When EQ_EN is LOW while SD/HD is HIGH, the device goes into BALANCE mode. This
mode is used during ORL measurement, disabling the AC signal path of the device
without powering it down. When in BALANCE mode, the device produces equal
pull-down currents in both differential shoulders of the serial data differential output,
effectively stopping the output at the output common mode voltage level. Gennum
recommends using BALANCE mode when measuring ORL with 2.5V termination
voltage.
GS2988 Dual-Slew-Rate, Cable Driver with 3Gb/s
12 of 17
Capability
Data Sheet
52131 - 4
December 2010
5. Application Information
5.1 PCB Layout
Special attention must be paid to component layout when designing serial digital
interfaces for HDTV.
An FR-4 dielectric can be used, however, controlled impedance transmission lines are
required for PCB traces longer than approximately 1cm. Note the following PCB artwork
features used to optimize performance:
•
The PCB trace width for HD rate signals is closely matched to SMT component
width to minimize reflections due to changes in trace impedance
•
The PCB ground plane is removed under the GS2988 output components to
minimize parasitic capacitance (NOTE: care should be taken, as removing too much
of the plane will make the system susceptible to EMI)
•
The PCB ground plane is removed under the GS2988 RSET pin and resistor to
minimize parasitic capacitance. The RSET resistor should be directly connected to
the VCC plane
•
•
Input and output BNC connectors are surface mounted in-line to eliminate a
transmission line stub caused by a BNC mounting via high-speed traces
High-speed traces are curved to minimize impedance variations due to change of
PCB trace width
NOTE: For more recommendations on Trace Lengths, ORL Inductor Values and other
PCB Layout Considerations, please refer to Gennum’s GS2989 Design Guide
(Doc ID 52070).
5.2 Typical Application Circuit
VCC
**Please refer to section 4.2.
10n
10n
9
16 10
6
VCC_Term
GND
4u7
4u7
GND
5n6*
1
2
10n
DDI
DDI
75R
75R
12
11
4u7
4u7
SDO
SDO
75R
75R
GS2988
VCC
VCC_Term
5n6*
4
RSET
R*
GND
10n
14
3
*Customer to choose resistor value.
GND
NOTE: All resistors in Ohms, capacitors in Farads,
and inductors in Henrys, unless otherwise stated.
* Typical value: varies with layout, and represents a trade-off
between good eye shape and output return loss.
5n6 is the optimum value for an 800mV output swing.
6n8 is the optimum value for an 1800mV output swing.
Figure 5-1: Typical Application Circuit
GS2988 Dual-Slew-Rate, Cable Driver with 3Gb/s
13 of 17
Capability
Data Sheet
52131 - 4
December 2010
6. Package & Ordering Information
6.1 Package Dimensions
4.00+/-0.05
2.76+/-0.10
A
DATUM A
B
PIN 1 AREA
CENTER TAB
DETAIL B
2X
C
0.15
DATUM B
2X
C
0.15
0.35+/-0.05
0.10
0.65
16X
A
B
C
0.05
C
C
DATUM A OR B
TERMINAL TIP
0.10
C
16X
C
0.08
0.65/2
0.65
SEATING PLANE
DETAIL B
SCALE:NTS
GS2988 Dual-Slew-Rate, Cable Driver with 3Gb/s
14 of 17
Capability
Data Sheet
52131 - 4
December 2010
6.2 Recommended PCB Footprint
0.35
0.65
0.55
3.70
2.76
CENTER PAD
NOTE: All dimensions
are in millimeters.
2.76
3.70
The Center Pad should be connected to the most negative power supply plane (VEE) by
a minimum of 5 vias.
NOTE: Suggested dimensions only. Final dimensions should conform to customer
design rules and process optimizations.
6.3 Packaging Data
Parameter
Value
Package type / dimensions / pad pitch
16-pin QFN / 4mm x 4mm /
0.65mm
Package Drawing Reference
Moisture Sensitivity Level
JEDEC M0220
3
Junction to Case Thermal Resistance, θ
31.0°C/W
j-c
Junction to Air Thermal Resistance, θ (at zero airflow)
43.8°C/W
j-a
Psi, Ψ
11.0°C/W
Yes
Pb-free and RoHS compliant, Halogen-free
GS2988 Dual-Slew-Rate, Cable Driver with 3Gb/s
15 of 17
Capability
Data Sheet
52131 - 4
December 2010
6.4 Solder Reflow Profiles
The device is manufactured with Matte-Sn terminations and is compatible with both
standard eutectic and Pb-free solder reflow profiles. MSL qualification was performed
using the maximum Pb-free reflow profile shown in Figure 6-1.
Temperature
60-150 sec.
20-40 sec.
260°C
250°C
3°C/sec max
217°C
6°C/sec max
200°C
150°C
25°C
Time
60-180 sec. max
8 min. max
Figure 6-1: Maximum Pb-free Solder Reflow Profile (Preferred)
6.5 Marking Diagram
Pin 1
Indicator
GS2988
XXXXE3
YYWW
Instructions:
GS2988
Package Mark
XXXX
Last 4 digits (excluding decimal) of
SAP Batch Assembly (FIN) as listed
on Packing Slip
Pb-free & Green indicator
Date Code
E3
YYWW
GS2988 Dual-Slew-Rate, Cable Driver with 3Gb/s
16 of 17
Capability
Data Sheet
52131 - 4
December 2010
6.6 Ordering Information
Part Number
Package
Temperature Range
GS2988
GS2988
GS2988-INE3
GS2988-INTE3
16-pin QFN
-40°C to 85°C
-40°C to 85°C
16-pin QFN
250pc Reel
GS2988
GS2988-INTE3Z
16-pin QFN
-40°C to 85°C
2,500pc Reel
CAUTION
ELECTROSTATIC SENSITIVE DEVICES
DOCUMENT IDENTIFICATION
DATA SHEET
The product is in production. Gennum reserves the right to make changes to
the product at any time without notice to improve reliability, function or
design, in order to provide the best product possible.
DO NOT OPEN PACKAGES OR HANDLE EXCEPT AT A
STATIC-FREE WORKSTATION
Phone: +1 (905) 632-2996
Fax: +1 (905) 632-2055
www.gennum.com
GENNUM CORPORATE HEADQUARTERS
4281 Harvester Road, Burlington, Ontario L7L 5M4 Canada
E-mail: corporate@gennum.com
OTTAWA
SNOWBUSH IP - A DIVISION OF GENNUM
GERMANY
232 Herzberg Road, Suite 101
Kanata, Ontario K2K 2A1
Canada
439 University Ave. Suite 1700
Toronto, Ontario M5G 1Y8
Canada
Gennum Canada Limited
Niederlassung Deutschland
München, Germany
Phone: +1 (613) 270-0458
Fax: +1 (613) 270-0429
Phone: +1 (416) 925-5643
Phone: +49 89 309040 290
Fax: +1 (416) 925-0581
Fax: +49 89 309040 293
E-mail: sales@snowbush.com
Web Site: http://www.snowbush.com
E-mail: gennum-germany@gennum.com
CALGARY
Suite 320, 3553 31st St. N.W.
Calgary, Alberta T2L 2K7
Canada
NORTH AMERICA WESTERN REGION
691 South Milpitas Blvd., Suite #200
Milpitas, CA 95035
United States
MEXICO
Venustiano Carranza 122 Int. 1
Centro, Aguascalientes
Mexico CP 20000
Phone: +1 (403) 284-2672
Fax: +1 (905) 632-2055
Phone: +1 (408) 934-1301
Fax: +1 (408) 934-1029
Phone: +1 (416) 848-0328
UNITED KINGDOM
South Building, Walden Court
Parsonage Lane,
Bishop’s Stortford Hertfordshire, CM23 5DB
United Kingdom
E-mail: naw_sales@gennum.com
JAPAN KK
Shinjuku Green Tower Building 27F
6-14-1, Nishi Shinjuku
Shinjuku-ku, Tokyo, 160-0023
Japan
NORTH AMERICA EASTERN REGION
4281 Harvester Road
Burlington, Ontario L7L 5M4
Canada
Phone: +44 1279 714170
Fax: +44 1279 714171
Phone: +81 (03) 3349-5501
Phone: +1 (905) 632-2996
Fax: +1 (905) 632-2055
Fax: +81 (03) 3349-5505
INDIA
E-mail: gennum-japan@gennum.com
Web Site: http://www.gennum.co.jp
#208(A), Nirmala Plaza,
Airport Road, Forest Park Square
Bhubaneswar 751009
India
E-mail: nae_sales@gennum.com
TAIWAN
6F-4, No.51, Sec.2, Keelung Rd.
Sinyi District, Taipei City 11502
Taiwan R.O.C.
Phone: +91 (674) 65304815
Fax: +91 (674) 259-5733
Phone: (886) 2-8732-8879
Fax: (886) 2-8732-8870
E-mail: gennum-taiwan@gennum.com
Gennum Corporation assumes no liability for any errors or omissions in this document, or for the use of the circuits or devices described herein. The sale of
the circuit or device described herein does not imply any patent license, and Gennum makes no representation that the circuit or device is free from patent
infringement.
All other trademarks mentioned are the properties of their respective owners.
GENNUM and the Gennum logo are registered trademarks of Gennum Corporation.
© Copyright 2009 Gennum Corporation. All rights reserved.
www.gennum.com
GS2988 Dual-Slew-Rate, Cable Driver with 3Gb/s
17 of 17
Capability
Data Sheet
17
52131 - 4
December 2010
相关型号：
©2020 ICPDF网 联系我们和版权申明