7MBP75RTJ060 [FUJI]
AC Motor Controller,;
| 型号： | 7MBP75RTJ060 |
| 厂家： | 
FUJI ELECTRIC |
| 描述： | AC Motor Controller, 电动机控制 |
| 文件： | 总77页 (文件大小：1921K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
Quality is our message
FUJI IGBT–IPM
APPLICATION MANUAL
Sep. 2004
REH983a
CONTENTS
Chapter 1 Features
1. GBT-IPMs Characteristics........................................................................1-2
2. IPM Characteristics by Series ..................................................................1-4
3. Definition of Type Name and Lot No.........................................................1-6
4. Lineup ......................................................................................................1-7
5. Outline Drawings......................................................................................1-8
Chapter 2 Description of Terminal Symbols and Terminology
1. Description of Terminal Symbols ..............................................................2-2
2. Description of Terminology.......................................................................2-3
Chapter 3 Description of Functions
1. Function Tables ........................................................................................3-2
2. Function Descriptions...............................................................................3-4
3. Truth Tables............................................................................................3-11
4. IPM Block Diagrams...............................................................................3-13
5. Timing Charts.........................................................................................3-21
Chapter 4 Examples of Application Circuits
1. Examples of Application Circuits ..............................................................4-2
2. Precautions ..............................................................................................4-7
3. Photocoupler and Peripheral Circuits.....................................................4-10
4. Connectors............................................................................................. 4-11
Chapter 5 Cooling Design
1. Cooler (Heat Sink) Selection Method.......................................................5-2
2. Notes on Heat Sink Selection...................................................................5-2
Chapter 6 Cautions on Use
1. Main Power Source..................................................................................6-2
2. Control Power Source ..............................................................................6-3
3. Protection Functions.................................................................................6-4
4. Power Cycling Capability..........................................................................6-6
5. Other ........................................................................................................6-6
Chapter 7 Trouble Shooting
1. Trouble Shooting......................................................................................7-2
2. Fault Analysis Diagrams...........................................................................7-2
3. Alarm Cause Analysis Diagram................................................................7-8
Quality is our message
Chapter 1
Features
Contents
Page
1 GBT-IPMs Characteristics .................................................................................1-2
2 IPM Characteristics by Series ...........................................................................1-4
3 Definition of Type Name and Lot No..................................................................1-6
4 Lineup................................................................................................................1-7
5 Outline Drawings ...............................................................................................1-8
1–1
Chapter 1 Features
1
GBT-IPMs Characteristics
An intelligent power module (IPM) has the following characteristics when compared with a combination
of IGBT modules and drive circuits.
1.1 Built-in drive circuit
• IGBT gate drives operate under optimal conditions.
• Since the wiring length between the internal drive circuit and IGBT is short and the impedance of the
drive circuit is low, no reverse bias DC source is required.
• The R-series IPM (R-IPM) devices require four control power sources, one source on the lower arm
side, and three individual sources on the upper arm side with proper circuit isolation.
1.2 Built-in protection circuits
• The following built-in protection circuits are included in the R-IPM devices:
(OC): Overcurrent protection
(SC): Short-circuit protection
(UV): Undervoltage protection for control power source
(OH): Overheating protection
(ALM): External alarm output
• The OC and SC protection circuits provide protection against IGBT damage caused by overcurrent or
load short-circuits. These circuits monitor the collector current using detection elements incorporated in
each IGBT and thus can minimize the possibility of severe damage to the IGBT. They also protect
against arm short-circuits.*1
• The UV protection circuit is in all of the IGBT drive circuits. This circuit monitors the Vcc supply voltage
level against the IGBT drive Vin.
• The OH protection circuit protects the IGBT and FWD from overheating. It also monitors the insulating
substrate’s temperature with temperature detection elements installed on the insulating substrates
inside the IPM.
(Case temperature overheating protection: TcOH)*2
1-2
Chapter 1 Features
• Additionally, each IGBT chip contains a temperature detection element on the IGBT die, which allows
the OH to act rapidly when abnormally high chip temperatures are detected. (Junction temperature
overheating protection: TjOH)
• The ALM circuit outputs an alarm signal to outside of the IPM, making it possible to shutdown the
system reliably by outputting the alarm signal to the microcontroller which controls IPM when the circuit
detects an abnormal condition (specified above). *2
*1 The N-line shunt resistance method is used for overcurrent detection of small-capacity types.
*2 Refer to Chapter 3 “Description of Functions” for the protective functions of each IPM.
1.3 Built-in brake circuit (7 in 1 IPM)
• For a motor control inverter application, a brake circuit can be built to protect bus overvoltage by just
adding a power dissipating resistor.
• The drive circuits and protection circuits are included in the brake IGBT in the same way as inverter
IGBTs.
1-3
Chapter 1 Features
2
IPM Characteristics by Series
2.1 R-IPM, R-IPM3 series
2.1.1 Small-capacity types
A lineup of small-capacity types with 15 to 30 A for 600 V systems and 15 A for 1200 V systems is
available. (P617, P619 package)
• P617 package products are a type without a copper base, while P619 package products are a type with
a copper base, which further improves the heat radiation ability.
• The control input terminals have a standard pitch of 2.54 mm.
• The shape of the main terminals is the Faston shape, and as the height is the same as that of the
control input terminals, connection by the same printed boards is possible with the soldering method as
well as with the connector method.
• By improvement of the trade-off between Vce(sat) and switching loss, the total loss has been improved.
• The chip is protected from abnormal heating by IGBT chip overheating protection.
2.1.2 Medium-capacity types (alarm output only for the lower arm)
A lineup of medium-capacity types with 50 to 150 A for 600 V systems and 25 to 75 A for 1200 V
systems is available. (P610, P611 package)
• The control input terminals have a standard pitch of 2.54 mm, they are arranged in one line, and
connection is possible with one connector for general use. A guide pin makes insertion of the connector
for the printed board easy.
• The main power source inputs (P, N), the brake output (B), and the output terminals (U, V, W) are
arranged close to each other, and the main wiring is a simple package construction.
• As the main terminals are M5 screws, large currents can be connected securely.
• The screw diameter for connection to the heat sink is M5, the same as for the main terminals.
• As all electrical connections are made by screws or connectors, soldering is not required and removal is
easy.
• By improvement of the trade-off between Vce(sat) and switching loss, the total loss has been improved.
• The chip is protected from abnormal heating by IGBT chip overheating protection.*3
*3 There is no alarm output from the upper arm side.
2.1.3 Medium-capacity types (with upper arm alarm output function)
A lineup of medium-capacity types with 50 to 150 A for 600 V systems and 25 to 75 A for 1200 V
systems is available. (P621 package)
• OC, SC, UV, and TjOH alarm signals can be output from the upper arm. This allows secure protection
against trouble from ground faults, etc.*4
• As the main terminals are M5 screws, large currents can be connected securely.
• The screw diameter for connection to the heat sink is M5, the same as for the main terminals.
1-4
Chapter 1 Features
• As all electrical connections are made by screws or connectors, soldering is not required and removal is
easy.
• By improvement of the trade-off between Vce(sat) and switching loss, the total loss has been improved.
• The chip is protected from abnormal heating by IGBT chip overheating protection.
*4 The TcOH alarm is output only from the lower arm.
2.1.4 Large-capacity types (alarm output only for the lower arm)
A lineup of large-capacity types with 200 to 300 A for 600 V systems and 100 to 150 A for 1200 V
systems is available. (P612 package)
• The layout of the control input terminals is the same as for the medium-capacity standard package, and
correspondence is possible with one connector type.
• The main power source inputs (P, N), the brake output (B), and the output terminals (U, V, W) are
arranged close to each other, and the main wiring is a simple package construction.
• As the main terminals are M5 screws, large currents can be connected securely.
• The screw diameter for connection to the heat sink is M5, the same as for the main terminals.
• As all electrical connections are made by screws or connectors, soldering is not required and removal is
easy.
• By improvement of the trade-off between Vce(sat) and switching loss, the total loss has been improved.
• The chip is protected from abnormal heating by IGBT chip overheating protection.*5
*5 There is no alarm output from the upper arm side.
2.2 Econo IPM series
The Econo IPM series is a lineup with 50 to 150 A for 600 V systems and 25 to 75 A for 1200 V systems.
(P622 package)
• In comparison with the medium-capacity types, the mounting area has been reduced by approximately
30% and the mass has been reduced by approximately 40%, contributing to reduction of the device size.
• As the height is the same as that of Econo DIMs (Econo Diode Modules), connection is possible with
the same printed circuit boards.
• OC, SC, UV, and TjOH alarm signals can be output from the upper arm. This makes secure protection
against trouble from ground faults etc. possible.
• The chip is protected from abnormal heating by IGBT chip overheating protection.
1-5
Chapter 1 Features
3
Definition of Type Name and Lot No.
• Type name
7 MBP 50 RT A 060 -01
Additional model number (if necessary)
Voltage rating
060: 600 V
120: 1200 V
Additional number of series
Series name
R: R-IPM
RT: R-IPM3
TE:EconoIPM
Inverter IGBT current rating
50: 50 A
Indicates IGBT-IPM
Number of main elements
7-chip circuit with built-in brake
6-chip circuit without dynamic brake
• Lot No.
4 1 01
Month of production
1: Jan.
9: Sep.
0: Oct.
N: Nov.
D: Dec.
Year of production
4: 2004
Type name
Lot No.
7M B P 50R T A 060
50A 600V Japan O
4101
1-6
Chapter 1 Features
4
Lineup
600 V system, 15 to 75 A
15A
20A
30A
50A
75A
R-IPM
6MBP15RH060
6MBP20RH060
6MBP30RH060
6MBP50RA060
7MBP50RA060
6MBP75RA060
7MBP75RA060
R-IPM3
6MBP20RTA060
6MBP50RTB060
7MBP50RTB060
6MBP50RTJ060
7MBP50RTJ060
6MBP75RTB060
7MBP75RTB060
6MBP75RTJ060
7MBP75RTJ060
−
−
Econo
IPM
6MBP50TEA060
7MBP50TEA060
6MBP75TEA060
7MBP75TEA060
−
−
−
600 V system, 100 to 300 A
100A
150A
200A
300A
R-IPM
6MBP100RA060
7MBP100RA060
6MBP150RA060
7MBP150RA060
6MBP200RA060
6MBP300RA060
7MBP200RA060
7MBP300RA060
R-IPM3
6MBP100RTB060
7MBP100RTB060
6MBP100RTJ060
7MBP100RTJ060
6MBP150RTB060
7MBP150RTB060
6MBP150RTJ060
7MBP150RTJ060
−
−
Econo
IPM
6MBP100TEA060
7MBP100TEA060
6MBP150TEA060
7MBP150TEA060
−
−
1200 V system
15A
25A
50A
75A
100A
150A
R-IPM
6MBP15RA120
6MBP25RA120
7MBP25RA120
6MBP25RJ120
7MBP25RJ120
6MBP50RA120
7MBP50RA120
6MBP50RJ120
7MBP50RJ120
6MBP75RA120
7MBP75RA120
6MBP75RJ120
7MBP75RJ120
6MBP100RA120
7MBP100RA120
6MBP150RA120
7MBP150RA120
Econo
IPM
6MBP25TEA120
7MBP25TEA120
6MBP50TEA120
7 MBP50TEA120
6MBP75TEA120
7MBP75TEA120
−
−
−
1-7
Chapter 1 Features
5
Outline Drawings
Fig. 1-1 Outline Drawing (P617)
Type name: 6MBP15RH060, 6MBP20RH060, 6MBP30RH060
1-8
Chapter 1 Features
1
10
4
7
15
Ｐ
Ｕ
Ｖ
Ｗ
Ｎ１ Ｎ２
Fig. 1-2 Outline Drawing (P619)
Type name: 6MBP20RTA060, 6MBP15RA120
1-9
Chapter 1 Features
Fig. 1-3 Outline Drawing (P610)
Type name: 6MBP50RA060, 6MBP75RA060, 6MBP50RTB060, 6MBP75RTB060, 6MBP25RA120
7MBP50RA060, 7MBP75RA060, 7MBP50RTB060, 7 MBP75RTB060, 7MBP25RA120
1-10
Chapter 1 Features
Fig. 1-4 Outline Drawing (P611)
Type name: 6MBP100RA060, 6MBP150RA060, 6MBP100RTB060, 6MBP150RTB060, 6MBP50RA120, 6MBP75RA120
7MBP100RA060, 7MBP150RA060, 7MBP100RTB060, 7MBP150RTB060, 7MBP50RA120, 7MBP75RA120
1-11
Chapter 1 Features
Fig. 1-5 Outline Drawing (P612)
Type name: 6MBP200RA060, 6MBP300RA060, 6MBP100RA120, 6MBP150RA120
7MBP200RA060, 7MBP300RA060, 7MBP100RA120, 7MBP150RA120
1-12
Chapter 1 Features
Fig. 1-6 Outline Drawing (P621)
Type name: 6MBP50RTJ060, 6MBP75RTJ060, 6MBP100RTJ060, 6MBP150RTJ060, 6MBP25RJ120, 6MBP50RJ120, 6MBP75RJ120
7MBP50RTJ060, 7MBP75RTJ060, 7MBP100RTJ060, 7MBP150RTJ060, 7MBP25RJ120, 7MBP50RJ120, 7MBP75RJ120
1-13
Chapter 1 Features
Fig. 1-7 Outline Drawing (P622)
Type name: 6MBP50TEA060, 6MBP75TEA060, 6MBP100TEA060, 6MBP150TEA060
6MBP25TEA120, 6MBP50TEA120, 6MBP75TEA120
7MBP50TEA060, 7MBP75TEA060, 7MBP100TEA060, 7MBP150TEA060
7MBP25TEA120, 7MBP50TEA120, 7MBP75TEA120
1-14
Quality is our message
Chapter 2
Description of Terminal Symbols and
Terminology
Contents
Page
1. Description of Terminal Symbols ......................................................................2-2
2. Description of Terminology ...............................................................................2-3
2–1
Chapter 2 Description of Terminal Symbols and Terminology
1
Description of Terminal Symbols
Main terminals
Terminal Symbol
Description
Main power source Vd input terminal for the inverter bridge.
P: + side, N: − side
P
N
Brake output terminal: terminal to connect the resistor for regenerative operation
B
declaration
3-phase inverter output terminal
U
V
W
Main power source Vd "negative(-)" input terminal after rectification converter
smoothing of the inverter unit (P617, 619)
N2
Terminal for external connection of resistance when the OC level is to be changed
(P617, 619)
N1
Control terminals
Terminal P610, P611
P617
P619
<1>
P621
P622
<1>
Description
Symbol
GND U
Vcc U
P612
Control power source Vcc input in the upper arm U phase
Vcc U: + side, GND U: − side
<1>
<3>
<2>
<3>
<4>
Vin U
<2>
<3>
Control signal input in the upper arm U phase
Upper arm U-phase alarm output when the protection
circuits are operating
ALM U
<2>
−
−
Control power source Vcc input in the upper arm V phase
Vcc V: + side, GND V: − side
GND V
Vcc V
Vin V
<4>
<6>
<5>
<4>
<6>
<5>
<5>
<8>
<7>
Control signal input in the upper arm V phase
Upper arm V-phase alarm output when the protection
circuits are operating
ALM V
<6>
−
−
Control power source Vcc input in the upper arm W phase
Vcc W : + side, GND W: − side
GND W
Vcc W
Vin W
<7>
<9>
<8>
<7>
<9>
<8>
<9>
<12>
<11>
Control signal input in the upper arm W phase
Upper arm W-phase alarm output when the protection
circuits are operating
ALM W
<10>
−
−
Control power source Vcc input in the lower arm common
Vcc: + side, GND: − side
GND
Vcc
Vin X
Vin Y
Vin Z
Vin DB
<10>
<11>
<13>
<14>
<15>
<12>
<10>
<11>
<12>
<13>
<14>
−
<13>
<14>
<16>
<17>
<18>
<15>
Control signal input in the lower arm X phase
Control signal input in the lower arm Y phase
Control signal input in the lower arm Z phase
Control signal input in the lower arm brake phase
Lower arm alarm output when the protection circuits are
operating
ALM
<16>
<15>
<19>
2-2
Chapter 2 Description of Terminal Symbols and Terminology
2
Description of Terminology
1. Absolute Maximum Ratings
Term
Symbol
Description
Bus voltage
VDC
DC voltage that can be applied between PN terminals
DC Bus voltage
VDC
Peak value of the surge voltage that can be applied between PN
(surge)
(surge)
terminals in switching
DC Bus voltage
(short circuit)
DC source voltage between PN terminals that can be protected from
short circuits/overcurrent
VSC
Maximum collector-emitter voltage of the built-in IGBT chip and
repeated peak reverse voltage of the FWD chip (only the IGBT for the
brake)
Collector-emitter
Voltage
VCES
Reverse voltage
Collector current
FRD forward Current
VR
IC
ICP
–IC
IF
Repeated peak reverse voltage of the FWD chip in the brake section
Maximum DC collector current for the IGBT chip
Maximum DC pulse collector current for the IGBT chip
Maximum DC forward current for the FWD chip
Maximum DC forward current for the FWD chip in the brake section
Maximum power dissipation for one IGBT element
Collector power
Dissipation
PC
Power dissipation for Tj to become 150°C at Tc = 25°C or power
dissipated in collector so that Tj becomes 150°C at Tc = 25°C
Control power source
voltage
Input voltage
Input current
Alarm signal voltage
Alarm signal current
Chip junction
Temperature
Operating case
temperature
VCC
Voltage that can be applied between GND and each Vcc terminal
Vin
Iin
VALM
IALM
Voltage that can be applied between GND and each Vin terminal
Current that flows between GND and each Vin terminal
Voltage that can be applied between GND and ALM terminal
Current that flows between GND and ALM terminal
Maximum junction temperature of the IGBT and FWD chips during
Tj
continuous operation
Range of case temperature for electrical operation (Fig. 1 shows the
measuring point of the case temperature Tc)
Range of ambient temperature for storage or transportation, when
there is no electrical load
Topr
Tstg
Storage temperature
Maximum effective value of the sine-wave voltage between the
terminals and the heat sink, when all terminals are shorted
simultaneously
Isolating voltage
Viso
Screw
Max. torque for connection of terminal and external wire with the
specified screw
Terminal
torque
−
−
Max. torque when mounting the element to the heat sink with the
specified screw
Mounting
2-3
Chapter 2 Description of Terminal Symbols and Terminology
2. Electrical Characteristics
2.1 Main Circuit
Term
Symbol
ICES
Description
Collector-emitter cutoff
Collector current when a specified voltage is applied between the
collector and emitter of an IGBT with all input signals H (= Vz)
Collector-emitter voltage at a specified collector current when the
input signal of only the elements to be measured is L (= 0V) and the
inputs of all other elements are H (= Vz)
current
Collector-emitter
V
CE (sat)
saturation voltage
Forward voltage at a specified forward current with all input signals H
(= Vz)
Diode forward voltage
Turn-on time
VF
The time from the input signal dropping below the threshold value until the
collector current becomes 90% of the rating. See Fig. 2-3.
The time from the input signal rising above the threshold value until the
collector current becomes 10% of the rating. See Fig. 2-3.
The time from the collector current becoming 90% at the time of IGBT turn-off
until the tangent to the decreasing current becomes 10%. See Fig. 2-3.
The time required for the reverse recovery current of the built-in diode to
disappear. See Fig. 2-3.
ton
toff
tf
Turn-off time
Fall time
Reverse recovery time
trr
2.2 Control Circuits
Term
Symbol
Description
Current flowing between control power source Vcc and GND on the P-side
(upper arm side)
Iccp
Iccn
Control power source
consumption current
Current flowing between control power source Vcc and GND on the N-side
(lower arm side)
Vinth (on) Control signal voltage when IGBT changes from OFF to ON
Vinth (off) Control signal voltage when IGBT changes from ON to OFF
Input signal threshold
voltage
Voltage clamped by zener diode connected between GND and each
Input zenor voltage
Vz
Vin when the control signal is OFF
Period in which an alarm continues to be output (ALM) from the ALM
Signal hold time
tALM
terminal after the N-side protection function is actuated
Limiting resistor for
alarm
Built-in resistance limiting the primary current of the photocoupler for
RALM
ALM output
Current detection shunt
resistance
R1
Resistance value of the IPM built-in shunt resistor (P617, P619)
2.3 Protection Circuits
Term
Symbol
IOC
Description
Overcurrent protective
IGBT collector current at which the overcurrent protection (OC) works
operation current
Overcurrent cut off time
tDOC
tsc
Shown in Fig. 2-1
Shown in Fig. 2-2
Short-circuit protection
delay time
Chip overheating
protection temperature
Chip overheating
protection hysteresis
Case overheating
protection temperature
Case overheating
protection hysteresis
Under voltage protection
level
Tripping temperature at which the IGBT chip junction temperature Tj
overheats and IGBT soft shutdown is performed
TjoH
TjH
Drop temperature required for output stop resetting after protection operation
Tripping temperature at which the IGBT performs soft shutdown when the
case temperature Tc shows overheating
TcOH
TcH
VUV
Drop temperature required for output stop resetting after protection operation
Tripping voltage at which the IGBT performs soft shutdown when the control
power source voltage Vcc drops
Control power source
undervoltage protection
hysteresis
Recovery voltage required for output stop resetting after protection
operation
VH
2-4
Chapter 2 Description of Terminal Symbols and Terminology
3. Thermal Characteristics
Term
Symbol
Description
Chip-case thermal
Rth (j-c)
Chip-case thermal resistance of IGBT or diode
resistance
Chip-fin thermal
resistance
Rth (c-f)
Thermal resistance between the case and heat sink, when mounted
on a heat sink at the recommended torque using the thermal
compound
Case temperature
Tc
IPM case temperature (temperature of the copper plate directly under
the IGBT or the diode)
4. Noise Tolerance
Term
Common mode noise
Electric surge
Symbol
Description
Common mode noise tolerance in our test circuit
Electric surge tolerance in our test circuit
−
−
5. Other
Term
Weight
Symbol
Wt
Description
Weight of IPM
Range of control signal frequencies for input to the control signal
Switching frequency
fsw
input terminal
Reverse recovery
current
Irr
Shown in Fig. 2-3
Reverse bias safe
operation area
Switching loss
Area of the current and voltage in which IGBT can be cut off under
specified conditions during turn-off
IGBT switching loss during turn-on
IGBT switching loss during turn-off
FWD switching loss during reverse recovery
RBSOA
Eon
Eoff
Err
Ioc
Ic
IALM
t
doc
Fig. 2-1 Overcurrent Protection Delay Time (tdoc)
2-5
Chapter 2 Description of Terminal Symbols and Terminology
tsc
Isc
Ic
Ic
Ic
IALM
IALM
IALM
Fig. 2-2 Short-circuit Protection Delay Time (tsc)
Input signal
(Vin)
Vinth (on)
Vinth (off)
trr
Irr
90%
10%
90%
Collector current
(Ic)
tf
toff
ton
Fig. 2-3 Switching Time
2-6
Quality is our message
Chapter 3
Description of Functions
Contents
Page
1. Function Tables ................................................................................................3-2
2. Function Descriptions.......................................................................................3-4
3. Truth Tables.....................................................................................................3-11
4. IPM Block Diagrams........................................................................................3-13
5. Timing Charts ..................................................................................................3-21
3–1
Chapter 3 Descriptions of Functions
1
Function Tables
The functions built into the IPM are shown in Tables 3-1 to 3-3.
Table 3-1 IPM Built-in Functions (R-IPM)
600 V system
Built-in Functions
Element
Number
Common for Upper and
Upper Arm
Lower Arm
Model
Package
Dr LUowVer ArmTjOH
OC ALM
OC
ALM
TcOH
6MBP15RH060
6MBP20RH060
6MBP30RH060
6MBP50RA060
6MBP75RA060
6MBP100RA060
6MBP150RA060
6MBP200RA060
6MBP300RA060
7MBP50RA060
7MBP75RA060
7MBP100RA060
7MBP150RA060
7MBP200RA060
7MBP300RA060
P617
P617
P617
P610
P610
P611
P611
P612
P612
P610
P610
P611
P611
P612
P612
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
−
−
−
√
√
√
√
√
√
√
√
√
√
√
√
−
−
−
−
−
−
−
−
−
−
−
−
−
−
−
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
−
−
−
√
√
√
√
√
√
√
√
√
√
√
√
6 in 1
7 in 1
1200 V system
Built-in Functions
Element
Number
Common for Upper and
Upper Arm
Lower Arm
Model
Package
Dr LUowVer ArmTjOH
OC ALM
OC
ALM
TcOH
6MBP15RA120
6MBP25RA120
6MBP50RA120
6MBP75RA120
6MBP100RA120
6MBP150RA120
7MBP25RA120
7MBP50RA120
7MBP75RA120
7MBP100RA120
7MBP150RA120
6MBP25RJ120
6MBP50RJ120
6MBP75RJ120
7MBP25RJ120
7MBP50RJ120
7MBP75RJ120
P619
P610
P611
P611
P612
P612
P610
P611
P611
P612
P612
P621
P621
P621
P621
P621
P621
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
−
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
−
−
−
−
−
−
−
−
−
−
−
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
−
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
6 in 1
7 in 1
6 in 1
7 in 1
Dr: IGBT drive circuit, UV: Control power source undervoltage protection, TjOH: Element overheating protection, OC: Overcurrent protection,
ALM: Alarm output, TcOH: Case overheating protection
3-2
Chapter 3 Descriptions of Functions
Table 3-2 IPM Built-in Functions (R-IPM3)
600 V system
Built-in Functions
Element
Number
Common for Upper and
Upper Arm
Lower Arm
Model
Package
Dr LUowVer ArmTjOH
OC ALM
OC
ALM
TcOH
6MBP20RTA060
6MBP50RTB060
6MBP75RTB060
6MBP100RTB060
6MBP150RTB060
7MBP50RTB060
7MBP75RTB060
7MBP100RTB060
7MBP150RTB060
6MBP50RTJ060
6MBP75RTJ060
6MBP100RTJ060
6MBP150RTJ060
7MBP50RTJ060
7MBP75RTJ060
7MBP100RTJ060
7MBP150RTJ060
P619
P610
P610
P611
P611
P610
P610
P611
P611
P621
P621
P621
P621
P621
P621
P621
P621
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
−
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
−
−
−
−
−
−
−
−
−
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
−
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
6 in 1
7 in 1
6 in 1
7 in 1
Dr: IGBT drive circuit, UV: Control power source undervoltage protection, TjOH: Element overheating protection, OC: Overcurrent protection,
LM: Alarm output, TcOH: Case overheating protection
3-3
Chapter 3 Descriptions of Functions
Table 3-3 IPM Built-in Functions (Econo IPM)
600 V system
Built-in Functions
Element
Number
Common for Upper and
Upper Arm
Lower Arm
Model
Package
Dr LUowVer ArmTjOH
OC ALM
OC
ALM
TcOH
6MBP50TEA060
6MBP75TEA060
6MBP100TEA060
6MBP150TEA060
7MBP50TEA060
7MBP75TEA060
7MBP100TEA060
7MBP150TEA060
P622
P622
P622
P622
P622
P622
P622
P622
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
−
−
−
−
−
−
−
−
6 in 1
7 in 1
1200 V system
Built-in Functions
Element
Number
Common for Upper and
Upper Arm
Lower Arm
Model
Package
Dr LUowVer ArmTjOH
OC ALM
OC
ALM
TcOH
6MBP25TEA120
6MBP50TEA120
6MBP75TEA120
7MBP25TEA120
7MBP50TEA120
7MBP75TEA120
P622
P622
P622
P622
P622
P622
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
−
−
−
−
−
−
6 in 1
7 in 1
Dr: IGBT drive circuit, UV: Control power source undervoltage protection,
ALM: Alarm output, TcOH: Case overheating protection
TjOH: Element overheating protection, OC: Overcurrent protection,
2
Function Descriptions
2.1 IGBT, FWD for 3-phase inverters
As shown in Fig. 3-1, IGBT and FWD for 3-phase inverters are built in, and a 3-phase bridge circuit is
formed inside the IPM. The main circuit is completed by connecting the main power source to the P and N
terminals and the 3-phase output lines to the U, V, and W terminals. Connect a snubber circuit to suppress
the surge voltages.
2.2 IGBT, FWD for brake
As shown in Fig. 3-1, IGBT and FWD for brake are built in, and an IGBT collector is connected internally
to the B terminal. By controlling the brake IGBT through connection of brake resistance between the
terminals P and B, the regeneration energy can be dissipated while decelerating to suppress the rise of
voltage between the P and N terminals.
3-4
Chapter 3 Descriptions of Functions
P-side
PWM input
IPM
Pre-Driver
Pre-Driver
Pre-Driver
P
B
U
V
W
N
Pre-D river
Brake
input
N-side
PWM input
Alarm
output
Fig. 3-1 3-Phase Inverter Application Model (in Case of 7MBP150RTB060)
2.3 IGBT drive function
Fig. 3-2 shows the pre-driver block diagram. As the IPM incorporates an IGBT drive function, the IGBT
can be driven without designing a gate resistance value by connecting the photocoupler output to the IPM.
The features of this drive function are introduced below.
• Independent gate resistance control
A special turn-on/turn-off Rg not using any exclusive gate resistance Rg is built in. With this, the dv/dt
of turn-on and turn-off can be controlled individually, so that the merits of the element are fully
demonstrated (Turn on/Normal Shutdown).
• Soft shutdown
During an overcurrent or other abnormality, the gate voltage is lowered softly and gently to prevent
element destruction by surge voltage (Soft Shutdown).
• Errorneous ON prevention
Since a circuit is set up to ground the gate electrode with low impedance while OFF, erroneous ON
caused by the rise of VGE due to noise can be prevented (Off Hold).
3-5
Chapter 3 Descriptions of Functions
• A reverse bias power source is not required.
As the IPM has a short wiring between the drive circuit and the IGBT, the wiring impedance is small,
making driving without reverse bias possible.
• Alarm latch
Alarms have a latch period of approximately 2 ms, and the IGBT does not operate even when an On-
signal enters during the latch period. In addition, as the alarms for each phase, including brake, on the
lower arm side are connected mutually, all IGBTs on the lower arm side are stopped for the latch period
when a protection operation is performed on the lower arm side.
3-6
Chapter 3 Descriptions of Functions
VccU
VinU
VinV
VinW
(Same circuit as X-phase)
GNDU
VccV
(Same circuit as X-phase)
(Same circuit as X-phase)
GNDV
VccW
GNDW
Vcc
Vcc
in
VinX
U
Turn on
IGBT
8V
gate
Gate Voltage
Off Hold
Vcc
Normal Shutdown
alarm
Soft Shutdown
N
Vcc
<1>
TjH
Filter
1 ms
Filter
5 us
TjOH
OC
UV
Q
S
R
20°C
<2>
Delay
2ms
Vcc
<3>
Filter
5 us
VH
0.5 V
GND
Pre-driver for X-phase IGBT
Note: Delay time and hysteresis are typical values.
(Same circuit as X-phase)
VinY
VinZ
(Same circuit as X-phase)
(Same circuit as X-phase)
VinDB
Tc overheating protection circuit
Vcc
Vcc
Vcc
<4>
ALM
TcH
Filter
1 ms
RALM
TcOH
Q
S
R
20°C
GND
Delay
2 ms
Fig. 3-2 IPM Function Block (Representative Model: 7MBP150RTB060)
3-7
Chapter 3 Descriptions of Functions
2.4 Overcurrent protection function (OC)
Two detection methods are used, the sense IGBT method and the shunt resistance method.
(1) Sense IGBT method
Models: P610/P611/P612/P621/P622
• The main current flowing in the IGBT is detected by taking the sense current flowing in the current
sense IGBT inside the IGBT chip into the control circuit. The sense current is extremely small in
comparison with the main current, so that the detection loss can be kept minimal in comparison with the
shunt resistance method.
• When the overcurrent protection Ioc level is exceeded for a duration of approximately 5 µs (tdoc), the
IGBT goes through a soft shutdown. As a detection filter is installed, faulty operations caused by
instantaneous overcurrents or noise can be prevented.
• When after approximately 2 ms the level drops below Ioc and the input signal is OFF, the alarm is
released.
(2) Shunt resistance method
Models: P617/P619
• Overcurrent protection is performed by detecting the voltage at both ends of the current detection shunt
resistance R1, connected to the DC bus bar line N. When the overcurrent detection level Ioc is
exceeded for a duration of approximately 5 µs (tdoc), the IGBT goes through a soft shutdown. As a
detection filter is installed, faulty operations caused by instantaneous overcurrents or noise can be
prevented.
• When after approximately 2 ms the level drops below Ioc and if the input signal is OFF, the alarm is
released.
2.5 Short-circuit protection function (SC)
The SC protection function always operates with the OC protection function to suppress the peak
current when a load or arm is shorted.
2.6 Undervoltage protection (UV)
• The UV protection function performs soft shutdown of the IGBT when the control source voltage (Vcc)
continuously drops below VUV for approximately 5 µs.
• As the hysteresis VH is provided, the alarm is released if Vcc recovers to VUV + VH or more after
approximately 2 ms and the input signal is OFF.
2.7 Case temperature overheating protection function (TcOH)
• The TcOH protection function detects the insulating substrate temperature with the temperature
detection elements set up on the same ceramic substrate as that on which the power chips (IGBT,
FWD) are set up and performs soft shutdown of the IGBT when the detected temperature exceeds the
protection level TcOH continuously for approximately 1 ms.
• As the hysteresis TcH is provided, the alarm is released if Tc drops below TcOH-TcH after approximately
2 ms.
• The TcOH detection positions are shown in Fig.3-3 to Fig.3-6.
3-8
Chapter 3 Descriptions of Functions
Fig. 3-3 TcOH Detection Position (P610)
Fig. 3-4 TcOH Detection Position (P611)
3-9
Chapter 3 Descriptions of Functions
Fig. 3-5 TcOH Detection Position (P612)
Fig. 3-6 TcOH Detection Position (P621)
3-10
Chapter 3 Descriptions of Functions
2.8 Chip temperature overheating protection function (TjOH)
• The TjOH protection function detects the IGBT chip temperature with the temperature detection
elements set up on all IGBT chips and performs soft shutdown of the IGBT when the detected
temperature exceeds the protection level (TjOH) continuously for approximately 1 ms or more.
• As the hysteresis TjH is provided, the alarm is released if Tj drops below TjOH-TjH after approximately 2
ms and the input signal is OFF.
2.9 Alarm output function (ALM)
• When a protection function operates, the alarm output terminal becomes conductive against each
reference potential GND. With open collector output, a function for direct drive of the photocoupler is
provided, and a 1.5 kΩ series resistor is built in.
• When a protection function operates, the alarm signal is output continuously for approximately 2 ms
(tALM). The alarm is released when the alarm cause has been removed, tALM has elapsed, and the
input signal is OFF. When the cause is TcOH, the alarm is released regardless of the input signal.
• As the alarm terminals of the drive circuit on the lower arm side are connected mutually, all IGBTs on
the lower arm side, including the brake, are stopped when any one of the IGBTs outputs an alarm.
3
Truth Tables
The truth tables when a fault occurs are shown in Tables 3-4 to 3-7.
Table 3-4 Truth Table (P617, P619)
IGBT
Cause of
Fault
Alarm Output
Low Side
U-phase
V-phase
W-phase
Low Side
UV
OFF
*
*
*
High
High
High
High
High
High
Low
Low
Low
High side
U-phase
TjOH
UV
OFF
*
*
*
*
*
*
*
*
*
*
OFF
*
*
*
High side
V-phase
TjOH
UV
OFF
*
*
*
*
*
*
OFF
*
High side
W-phase
TjOH
OC
OFF
*
*
*
*
OFF
OFF
OFF
Low side
UV
TjOH
* Depends on input logic
3-11
Chapter 3 Descriptions of Functions
Table 3-5 Truth Table (P610, P611, P612)
Cause of
IGBT
Alarm Output
Low Side
High
Fault
U-phase
V-phase
W-phase
Low Side
OC
UV
OFF
*
*
*
High side
U-phase
OFF
OFF
*
*
*
*
High
TjOH
OC
*
*
High
*
*
*
*
*
*
*
*
*
*
OFF
*
*
High
High side
V-phase
UV
OFF
*
*
*
High
TjOH
OC
OFF
*
High
*
*
*
*
*
*
*
OFF
*
High
High side
W-phase
UV
OFF
*
High
TjOH
OC
OFF
*
High
*
*
*
*
OFF
OFF
OFF
OFF
Low
UV
Low
Low side
TjOH
TcOH
Low
Low
* Depends on input logic
Table 3-6 Truth Table (P621)
IGBT
Alarm Output
Cause of
Fault
U-phase
V-phase
W-phase
Low Side
ALMU
ALMV
ALMW
ALM
OC
UV
OFF
*
*
*
Low
Low
Low
High
High
High
High
High
High
High
High
High
High
High
High
High
Low
Low
Low
High
High
High
High
High
High
High
High
High
High
High
High
High
Low
Low
Low
High
High
High
High
High
High
High
High
High
High
High
High
High
Low
Low
Low
Low
High side
U-phase
OFF
*
*
*
TjOH
OC
OFF
*
*
*
*
*
*
*
*
*
*
*
*
*
OFF
*
*
High side
V-phase
UV
OFF
*
*
*
TjOH
OC
OFF
*
*
*
*
*
*
*
*
OFF
*
High side
W-phase
UV
OFF
*
TjOH
OC
OFF
*
*
*
*
*
OFF
OFF
OFF
OFF
UV
Low side
TjOH
TcOH
* Depends on input logic
Table 3-7 Truth Table (P622)
IGBT
Alarm Output
ALMV ALMW
Cause of
Fault
U-phase
V-phase
W-phase
Low Side
ALMU
ALM
OC
OFF
*
*
*
Low
Low
Low
High
High
High
High
High
High
High
High
High
High
High
High
Low
Low
Low
High
High
High
High
High
High
High
High
High
High
High
High
Low
Low
Low
High
High
High
High
High
High
High
High
High
High
High
High
Low
Low
Low
High side
U-phase
UV
OFF
*
*
*
TjOH
OC
OFF
*
*
*
*
*
*
*
*
*
*
*
*
OFF
*
*
High side
V-phase
UV
OFF
*
*
TjOH
OC
OFF
*
OFF
OFF
OFF
*
*
*
*
*
*
*
*
*
High side
W-phase
UV
*
TjOH
OC
*
OFF
OFF
OFF
Low side
UV
*
*
TjOH
* Depends on input logic
3-12
Chapter 3 Descriptions of Functions
4
IPM Block Diagrams
The IPM block diagrams are shown in Fig. 3-7 to Fig. 3-14.
VinU
Pre-driver 1
8V
GNDU
U
V
VccV
VinV
GNDV
VccW
VinW
GNDW
Vcc
W
VinX
VinY
Pre-driver 2
VinZ
ALM
N1
R1
N2
GND
Fig. 3-7 IPM Block Diagram (P617)
3-13
Chapter 3 Descriptions of Functions
VinU
Pre-driver 1
8V
GNDU
VccV
U
V
VinV
GNDV
VccW
VinW
GNDW
Vcc
W
VinX
VinY
VinZ
ALM
Pre-driver 2
1.5k
N1
R1
N2
GND
Fig. 3-8 IPM Block Diagram (P619)
3-14
Chapter 3 Descriptions of Functions
P
VccU
VinU
Pre-driver
8V
U
V
GNDU
VccV
VinV
GNDV
VccW
VinW
W
GNDW
Vcc
VinX
GND
VinY
VinZ
B
N
VinDB
ALM
Tc overheating
protection circuit
1.5k
Fig. 3-9 IPM Block Diagram (P610, P611, P612 with Built-in Brake)
3-15
Chapter 3 Descriptions of Functions
P
VccU
VinU
Pre-driver
8V
U
V
GNDU
VccV
VinV
GNDV
VccW
VinW
W
GNDW
Vcc
VinX
GND
VinY
VinZ
N
VinDB
B
NC
NC
Tc overheating
protection circuit
ALM
1.5k
Fig. 3-10 IPM Block Diagram (P610, P611, P612 Without Brake)
3-16
Chapter 3 Descriptions of Functions
P
VccU
VinU
ALMU
Pre-driver
1.5k
1.5k
8V
U
V
GNDU
VccV
VinV
ALMV
GNDV
VccW
VinW
ALMW
1.5k
W
GNDW
Vcc
VinX
GND
VinY
VinZ
B
N
VinDB
Tc overheating
protection circuit
ALM
1.5k
Fig. 3-11 IPM Block Diagram (P621 with Built-in Brake)
3-17
Chapter 3 Descriptions of Functions
P
VccU
VinU
ALMU
Pre-driver
1.5k
1.5k
1.5k
8V
GNDU
VccV
U
V
VinV
ALMV
GNDV
VccW
VinW
ALMW
W
GNDW
Vcc
VinX
GND
VinY
VinZ
N
B
VinDB
NC
NC
Tc overheating
protection circuit
ALM
1.5k
Fig. 3-12 IPM Block Diagram (P621 Without Brake)
3-18
Chapter 3 Descriptions of Functions
P
VccU
VinU
ALMU
Pre-driver
1.5k
1.5k
1.5k
8V
U
V
GNDU
VccV
VinV
ALMV
GNDV
VccW
VinW
ALMW
W
GNDW
Vcc
VinX
GND
VinY
VinZ
B
N
VinDB
ALM
1.5k
Fig. 3-13 IPM Block Diagram (P622 with Built-in Brake)
3-19
Chapter 3 Descriptions of Functions
P
VccU
VinU
ALMU
Pre-driver
1.5k
1.5k
1.5k
8V
U
V
GNDU
VccV
VinV
ALMV
GNDV
VccW
VinW
ALMW
GNDW
Vcc
W
VinX
GND
VinY
VinZ
N
B
VinDB
ALM
NC
NC
1.5k
Fig. 3-14 IPM Block Diagram (P622 Without Brake)
3-20
Chapter 3 Descriptions of Functions
5
Timing Charts
The timing charts for the protection functions are shown in Fig. 3-15 to Fig. 3-21.
Undervoltage protection (UV) (1)
V
UV + VUH
UV
V
< 5 s
µ
< 5 s
µ
VCC
Vin
IC
5
µ
s
5
µ
s
IALM
t
ALM
t
ALM
<1>
<2>
<4>
<5>
<6>
<8>
<3>
<7>
Fig. 3-15 Timing Chart UV (1)
Refer to Fig. 3-2 <3>.
<1> If Vcc is below VUV + VH while VCC is ON, an alarm is output.
<2> If the period in which VCC falls below VUV is shorter than 5 µs, the protection function does not work
(while Vin is OFF).
<3> An alarm is output when a period of about 5 µs elapses after VCC falls below VUV if Vin is OFF, and
IGBT remains OFF.
<4> If VCC returns to VUV + VH after tALM elapses, UV is reset after tALM elapses if Vin is OFF and the
alarm is also reset simultaneously.
<5> If the period in which VCC falls below VUV is shorter than 5 µs, the protection function does not work
(while Vin is ON).
<6> An alarm is output when a period of about 5 µs elapses after VCC falls below VUV if Vin is ON, and
a soft IGBT shutdown occurs.
<7> If VCC returns to VUV + VH after tALM elapses, UV is reset after tALM elapses if Vin is OFF and the
alarm is also reset simultaneously.
<8> An alarm is output if VCC falls below VUV while VCC c is OFF.
3-21
Chapter 3 Descriptions of Functions
Undervoltage protection (UV) (2)
V
UV + VUH
UV
V
V
CC
Vin
I
C
µ
5 s
µ
5 s
I
ALM
tALM
t
ALM
<1>
<2>
<3>
<4>
Fig. 3-16 Timing Chart UV (2)
Refer to Fig. 3-2 <3>.
<1> If Vcc is below VUV + VH while VCC is ON, an alarm is output. (Until Vin changes to OFF)
<2> If Vcc returns to VUV + VH after tALM elapses, UV and the alarm are reset simultaneously with the
return of VUV + VH if Vin is OFF.
<3> Even if VCC returns to VUV + VH after tALM elapses, UV is not reset after tALM elapses if Vin is ON.
UV and the alarm are reset simultaneously with Vin OFF.
<4> If Vin is ON while VCC is OFF, the alarm is output, and a soft IGBT shutdown is executed while VCC
is below VUV.
3-22
Chapter 3 Descriptions of Functions
Overcurrent protection (OC)
V
in
I
OC
I
C
IALM
t
doc
t
doc
< tdoc
< tdoc
t
ALM
t
ALM
<4>
<5>
<6>
<1>
<2>
<3>
Fig. 3-17 Timing Chart OC
Refer to Fig. 3-2 <3>.
<1> An alarm is output and a soft IGBT shutdown is executed when tDOC elapses after Ic rises above
Ioc.
<2> OC and the alarm are reset simultaneously if Vin is OFF when tALM elapses.
<3> An alarm is output and a soft IGBT shutdown is executed when tDOC elapses after Ic rises above
Ioc.
<4> If Vin is ON when tALM elapses, OC is not reset. OC and the alarm are reset simultaneously when
Vin is OFF.
<5> If Vin changes to OFF before tDOC elapses after Ic rises above Ioc, the protection function is not
activated and a normal IGBT shutdown is executed.
<6> If Vin changes to OFF before tDOC elapses after Ic rises above Ioc, the protection function is not
activated and a normal IGBT shutdown is executed.
3-23
Chapter 3 Descriptions of Functions
Short-circuit protection
V
in
I
SC
OC
I
IC
IALM
t
doc
tdoc
< tdoc
< tdoc
t
ALM
tALM
<1>
<2>
<3>
<5>
<6>
<4>
Fig. 3-18 Timing Chart SC
Refer to Fig. 3-2 <2>.
<1> If the load shorts after Ic has started flowing and Ic exceeds Isc, the Ic peak is suppressed
instantly. An alarm is output and a soft IGBT shutdown is executed when tDOC elapses.
<2> OC and the alarm are reset simultaneously if Vin is OFF when tALM elapses.
<3> If the load shorts and Isc is exceeded simultaneously with the start of flow of Ic, the Ic peak is
instantly suppressed. An alarm is output and a soft IGBT shutdown is executed after tDOC elapses.
<4> If Vin is ON when tALM elapses, OC is not reset. OC and the alarm are reset simultaneously when
Vin is OFF.
<5> If the load shorts after Ic has started flowing and Ic exceeds Isc, the Ic peak is suppressed
instantly. Then, if Vin changes to OFF before tDOC elapses, the protection function is not activated
and a normal IGBT shutdown occurs.
<6> If the load shorts simultaneously with the start of flow of Ic and Ic exceeds Isc, the Ic peak is
suppressed instantly. Then, if Vin changes to OFF before tDOC elapses, the protection function is
not activated and a normal IGBT shutdown is executed.
3-24
Chapter 3 Descriptions of Functions
Case temperature overheating protection (TcOH)
Vin
TcOH
TcOH to TcH
TC
IC
IALM
1 ms
1 ms
tALM
1 ms
tALM
tALM
<3>
<4>
<2>
<3>
<1>
Fig. 3-19 Timing Chart TcOH
Refer to Fig. 3-2 <4>.
<1> An alarm is output if the case temperature Tc continuously exceeds TCOH for a period of about 1
ms, and if Vin is ON, a soft shutdown of all IGBTs on the lower arm side is executed.
<2> If Tc falls below TCOH-TCH before tALM elapses, the alarm is reset when tALM elapses.
<3> If Tc exceeds continuously TCOH for a period of about 1 ms, an alarm is output. (While Vin is OFF)
<4> If Tc has not fallen below TCOH-TCH when tALM elapses, the alarm is not reset. When Tc falls below
TCOH-TCH after tALM elapses, the alarm is reset.
3-25
Chapter 3 Descriptions of Functions
IGBT chip overheating protection (TjOH) (1)
V
in
TjOH
TjOH to TjH
Tj
IC
IALM
1 ms
tALM
1 ms
t
ALM
1 ms
t
ALM
<1>
<3>
<3>
<4>
<2>
Fig. 3-20 Timing chart TjOH (1)
Refer to Fig. 3-2 <4>.
<1> An alarm is output and a soft IGBT shutdown is executed if the IGBT chip temperature Tj
continuously exceeds TjOH for a period of about 1 ms.
<2> If Tj falls below TjOH-TjH before tALM elapses, OH and the alarm are simultaneously reset if Vin is
OFF when tALM elapses.
<3> An alarm is output if Tj continuously exceeds TjOH for a period of about 1 ms, and if Vin is OFF, the
protection function is not activated.
<4> When Tj falls below TjOH-TjH after tALM elapses, OH and the alarm are reset simultaneously if Vin is
OFF.
3-26
Chapter 3 Descriptions of Functions
IGBT chip overheating protection (TjOH) (2)
Vin
TjOH
TjOH to TjH
Tj
3
s <
µ
I
C
I
ALM
< 1 ms
1 ms
tALM
< 1 ms
1 ms
tALM
<1>
<3>
<2>
Fig. 3-21 Timing Chart TjOH (2)
Refer to Fig. 3-2.
<1> If Tj exceeds TjOH and then falls below TjOH within about 1 ms, OH does not operate regardless of
whether Vin is ON or OFF.
<2> If Tj exceeds TjOH and then falls below TjOH within about 1 ms, OH does not operate regardless of
whether Vin is ON or OFF.
<3> If Tj exceeds TjOH and then falls below TjOH for a period of about 3 µs or longer, the 1 ms detection
timer is reset.
3-27
Quality is our message
Chapter 4
Examples of Application Circuits
Contents
Page
1. Examples of Application Circuits.......................................................................4-2
2. Precautions ......................................................................................................4-7
3. Photocoupler and Peripheral Circuits ..............................................................4-10
4. Connectors......................................................................................................4-11
4–1
Chapter 4 Examples of Application Circuit
1
Examples of Application Circuits
Fig. 4-1 shows an example of an application circuit for P610, P611, and P612 (types with built-in brake).
P
20 kΩ
20 kΩ
20 kΩ
0.1 µF
0.1 µF
0.1 µF
10 µF
10 µF
10 µF
IF
IF
IF
Vcc
Vcc
Vcc
U
V
+
M
W
B
N
0.1 µF
0.1 µF
0.1 µF
0.1 µF
20 kΩ
20 kΩ
20 kΩ
20 kΩ
10 µF
IF
IF
IF
IF
Vcc
5 V
10 nF
Fig. 4-1 Example of Application Circuit for P610, P611, and P612 (Types with Built-in Brake)
4-2
Chapter 4 Examples of Application Circuit
Fig. 4-2 shows an example of an application circuit for P610, P611, and P612 (types without brake).
20 kΩ
20 kΩ
20 kΩ
0.1 µF
0.1 µF
0.1 µF
P
10 µF
10 µF
10 µF
IF
IF
IF
Vcc
Vcc
Vcc
U
V
+
M
W
B
N
Connect to P or N.
0.1 µF
0.1 µF
0.1 µF
20 kΩ
20 kΩ
20 kΩ
10 µF
IF
IF
IF
Vcc
Connect to Vcc or GND
5 V
10 nF
Fig. 4-2 Example of Application Circuit for P610, P611, and P612 (Types Without Brake)
4-3
Chapter 4 Examples of Application Circuit
Fig. 4-3 shows an example of an application circuit for P621 and P622 (types with built-in brake).
P
20 kΩ
20 kΩ
20 kΩ
0.1 µF
0.1 µF
0.1 µF
10 µF
10 µF
10 µF
IF
Vcc
U
V
5 V
10 nF
+
IF
Vcc
W
5 V
10 nF
B
N
IF
Vcc
5 V
10 nF
0.1 µF
0.1 µF
0.1 µF
20 kΩ
20 kΩ
20 kΩ
10 µF
IF
Vcc
IF
IF
IF
0.1 µF
20 kΩ
5 V
10 nF
Fig. 4-3 Example of Application Circuit for P621, P622 (with Upper Arm Alarm)
(Types with Built-in Brake)
4-4
Chapter 4 Examples of Application Circuit
Fig. 4-4 shows an example of an application circuit for P621 and P622 (types without brake).
20 kΩ
20 kΩ
20 kΩ
0.1 µF
P
10 µF
IF
Vcc
U
V
5 V
10 nF
0.1 µF
+
10 µF
IF
Vcc
W
5 V
0.1 µF
B
N
P621: Connect to P or N
P622: Connect to N
10 µF
IF
Vcc
5 V
10 nF
0.1 µF
0.1 µF
0.1 µF
20 kΩ
20 kΩ
20 kΩ
10 µF
IF
IF
IF
Vcc
Connect to Vcc or GND
5 V
10 nF
Fig. 4-4 Example of Application Circuit for P621, P622 (with Upper Arm Alarm) (Types Without Brake)
4-5
Chapter 4 Examples of Application Circuit
Fig. 4-5 shows an example of an application circuit for P617.
P
20 kΩ
20 kΩ
20 kΩ
0.1 µF
0.1 µF
0.1 µF
10 µF
10 µF
10 µF
IF
IF
IF
Vcc
Vcc
Vcc
U
V
+
M
W
1
0.1 µF
0.1 µF
0.1 µF
20 kΩ
20 kΩ
20 kΩ
N2
10 µF
IF
IF
IF
Vcc
5 V
1.5 kΩ
10 nF
Fig. 4-5 Example of Application Circuit for Small-capacity IPM P617
4-6
Chapter 4 Examples of Application Circuit
Fig. 4-6 shows an example of an application circuit for P619.
P
20 kΩ
20 kΩ
20 kΩ
0.1 µF
0.1 µF
0.1 µF
10 µF
IF
IF
IF
Vcc
Vcc
Vcc
U
V
10 µF
+
M
W
10 µF
1
0.1 µF
0.1 µF
0.1 µF
20 kΩ
20 kΩ
20 kΩ
N2
10 µF
IF
Vcc
IF
IF
5 V
10 nF
Fig. 4-6 Example of Application Circuit for Small-capacity IPM P619
2
Precautions
2.1 Control power source
As shown in the application circuit examples, a total of four isolation power sources are required for the
control power sources, 3 on the upper arm side and 1 on the lower arm side.
If you are using commercial power source units, do not connect the GND terminal on the side of the
power source output.
When the GND on the output side is connected to + or -, faulty operation occurs because each power
source is connected to the ground on the side of power source input. Stray capacity between each power
source and ground should be reduced to a minimum.
4-7
Chapter 4 Examples of Application Circuit
2.2 Structural isolation among four power sources (input connectors and PC boards)
Isolation is needed between each of the four power sources and the main power source.
Since a large amount of dv/dt is applied to this isolation during IGBT switching, keep sufficient
clearance between the components and the isolation. (2 mm or more is recommended.)
2.3 GND connection
The control power source GND on the lower arm side and the main power source GND are connected
inside the IPM. Never connect them outside the IPM. If you connect them outside the IPM, loop currents
generated inside and outside the IPM flow to the lower arm due to di/dt and cause malfunctioning of the
photocoupler and the IPM. The input circuit of the IPM may also be damaged.
2.4 Control power source capacitor
The 10 µF and 0.1 µF capacitors connected to each control power source as shown in the application
circuit examples are not intended for smoothing the control power sources, but for compensating the
wiring impedance up to the IPM. Capacitors for smoothing are needed separately.
Since transient variations may be caused in the wiring impedance from the capacitor to the control
circuit, connect the capacitor as close to the IPM control terminal and photocoupler pin as possible.
Select capacitors with lower impedance and better frequency characteristics for the electrolytic
capacitors. In addition, connect capacitors with better frequency characteristics, such as film capacitors, in
parallel.
2.5 Alarm circuits
• The potential on the secondary side of the alarm photocoupler may vary due to dv/dt. It is
recommended to stabilize the potential by connecting a capacitor of approximately 10 nF.
• As P617 does not have a built-in alarm resistor, a resistor of 1.5 kΩ must be connected on the outside
of the IPM.
2.6 Pull-up of the signal input terminal
Pull up the control signal input terminal to Vcc with a resistor of 20 kΩ. Even if you do not use the brake
in the built-in brake IPM, still pull up the DB input terminal. If you do not pull up the terminal, a malfunction
may be caused by dv/dt.
2.7 Snubber
Connect the snubber to the PN terminals directly. For the P612 package set up the snubber for each
PN terminal on both sides.
2.8 B terminal
In the case of the 6 in 1 package (without brake) type, connecting the B terminal to the N or P terminal
as described below is recommended.
P610, P611, P612, P621 ············N or P terminal
P622(Econo-IPM) ························N terminal (connection to the P terminal causes an internal short-circuit)
4-8
Chapter 4 Examples of Application Circuit
2.9 Upper arm alarm
When the upper arm alarm of an IPM with upper arm alarm output is not used, connect the alarm
terminal to Vcc to stabilize the potential.
2.10 Overcurrent protection for small-capacity IPMs
The limit level for overcurrent protection can be adjusted to a high level by adding a resistor between
the N1 and N2 terminals of small-capacity IPMs (P617, 619). The resistor added at that time must be
mounted close to the N1 and N2 terminals. A long distance from the N1 and N2 terminals can cause faulty
operation of the IPM.
2.11 IPM input circuit
The constant-current circuit shown in Fig. 4-7 is provided in the input section of our IPMs, and outflow
from the IPM takes place at the timing shown in the figure. For this reason, the IF on the primary side of
the photocoupler must be determined so that a current of IR + 1 mA flows through the pull-up resistor on
the secondary side of the photocoupler. If the IF is not sufficient, faulty operation on the secondary side is
possible.
Also, the pull-up resistor must be selected so that a current of IR + 1 mA flows on the secondary side of
the photocoupler when the photocoupler is ON and that the current flowing into the IPM at the time of OFF
does not exceed the Iin MAX listed in the specifications.
IPM
Vcc
Constant-current circuit
Pull-up resistor R
Photocoupler
SW1
I
R
1 mA
Vin
Constant-current circuit
SW2
Vcc = 15V
Zener diode −8 V
GND
1 mA flows.
1 mA flows.
IPM
Vin
SW1 ON
SW2 OFF
SW1 OFF
SW2 ON
SW1 ON
SW2 OFF
Fig. 4-7 IPM Input Circuit and Rated Current Operation Timing
4-9
Chapter 4 Examples of Application Circuit
3
Photocoupler and Peripheral Circuits
3.1 Photocoupler for control input
z Photocoupler rating
Use a photocoupler satisfying the following characteristics.
• CMH = CML > 15 kV/µs or 10 kV/µs
• tpHL = tpLH < 0.8 µs
• tpLH-tpHL = −0.4 to 0.9 µs
• CTR > 15%
Example: Product of Agilent: HCPL-4504
Product of Toshiba: TLP759 (IGM)
Note: Safety standards such as UL and VDE should also be applied.
z Wiring between photocoupler and IPM
Make the wiring between the photocoupler and the IPM as short as possible to reduce the wiring
impedance between the photocoupler and the IPM control terminal. Separate each wire between the
primary and secondary circuits so that floating capacitance does not become large, since a strong dv/dt is
applied between the primary and secondary circuits.
z Light emitting diode driving circuit
The dv/dt withstand capability of the photocoupler is also affected by the input light emitting diode driving
circuit. A driving circuit example is shown in Fig. 4-8.
Bad example: Open collector
Good example: Totempole output IC
Current limiting resistor on the cathode side of the photo diode
Bad example: Current limiting resistor on the anode side of the photo diode
Good example: Photo diode A-K is shorted by transistors C-E
(example which is particularly fit for photocoupler OFF)
Fig. 4-8 Photocoupler Input Circuits
4-10
Chapter 4 Examples of Application Circuit
3.2 Photocoupler for alarm output
z Photocoupler rating
General-purpose photocouplers can be used, but photocouplers satisfying the following characteristics are
recommended.
• 100%< CTR< 300%
• Single-element type
Example: TLP521-1-GR rank
Note: Safety standards such as UL and VDE should also be applied.
z Input current limiting resistor
A current limiting resistor for the light emitting diode in the photocoupler input is included in the IPM.
RALM = 1.5 kΩ and if connected directly to Vcc, about 10 mA of IF flows with Vcc = 15 V.
Therefore, there is no need to connect any current limiting resistor.
However, if a large amount of current, i.e., Iout > 10 mA, is needed on the photocoupler output, increase
the CTR value of the photocoupler to the required value.
z Wiring between the photocoupler and the IPM
Since a large amount of dv/dt is also applied on the photocoupler for the alarm, the same precautions as
described in 3.1 should be taken.
4
Connectors
Connectors suitable for the shape of the R-IPM control terminals are commercially available.
16-pin connector for P610, 611, 612: MDF7-25S-2.54DSA made by Hirose Electric
For P621: DF10-31S-2DSA made by Hirose Electric
Please confirm the reliability and the specifications of the above connectors with the manufacturer.
4-11
Quality is our message
Chapter 5
Cooling Design
Contents
Page
1. Cooler (Heat Sink) Selection Method ...............................................................5-2
2. Notes on Heat Sink Selection...........................................................................5-2
5–1
Chapter 5 Cooling Design
1
Cooler (Heat Sink) Selection Method
• To safeguard operation of the IGBT, make sure the junction temperature Tj does not exceed Tjmax.
Cooling should be designed in such a way that ensures that Tj is always below Tjmax even in abnormal
states such as overload operation as well as under the rated load.
• Operation of IGBT at temperatures higher than Tjmax could result in damage to the chips.
In the IPM, the TjOH protection function operates when the chip temperature of IGBT exceeds Tjmax.
However, if the temperature rises too quickly, the chip may not be protected.
• Likewise, note that the chip temperature of FWD should not exceed Tjmax.
• When selecting the cooler (heat sink), always measure the temperature directly under the center of the
chip. The Econo IPM series in particular is designed with operational preconditions for servo
applications, etc., in which the temperature increases/decreases in a short time, so care is required in
regard to heat accumulation when using under other conditions. As the structure and design place
special importance upon compactness, there is a tendency for heat to accumulate in the power chip
located at the center. For the chip layout, refer to the IPM internal structure drawing: MT6M5313. For
the concrete design, refer to the following document.
“IGBT MODULE APPLICATION MANUAL REH984”
Contents: • Power dissipation loss calculation
• Selecting heat sinks
• Heat sink mounting precautions
• Troubleshooting
2
Notes on Heat Sink Selection
How to select heat sinks is described in the manual REH982. Note also the following points.
• Flatness of the heat sink surface
Flatness between mounting screw pitches: 0 to +100 µm, roughness: 10 µm or less
If the heat sink surface is concave, a gap occurs between the heat sink and the IPM, leading to
deterioration of cooling efficiency.
If the flatness is +100 µm or more, the copper base of the IPM is deformed and cracks could occur in
the internal isolating substrates.
5-2
Quality is our message
Chapter 6
Cautions on Use
Contents
Page
1. Main Power Source ..........................................................................................6-2
2. Control Power Source ......................................................................................6-3
3. Protection Functions.........................................................................................6-4
4. Power Cycling Capability..................................................................................6-6
5. Other ................................................................................................................6-6
6–1
Chapter 6 Precautions for Use
1
Main Power Source
1.1 Voltage range
1.1.1 600 V system IPMs
• The main power source should not exceed 500 V (= VDC(surge)) between the P and N main terminals.
The voltage between the collector and emitter main terminals (= VCES) should not exceed 600 V (=
absolute max. rated voltage).
• Surge voltage occurs in the wiring inductance inside the IPM due to di/dt during switching, but the
product is designed so that 600 V is not exceeded between the collector and emitter main terminals
when the main power source is used at VDC(surge) or lower between the P and N main terminals.
• In order for the maximum surge voltage at the time of switching not to exceed the rated voltage, keep
the connecting wires between the IPM and the embedded product short and install a snubber close to
the P and N terminals.
1.1.2 1200 V system IPMs
• The main power source should not exceed 1000 V (= VDC(surge)) between the P and N main terminals.
The voltage between the collector and emitter main terminals (= VCES) should not exceed 1200 V (=
absolute max. rated voltage).
• Surge voltage occurs in the wiring inductance inside the IPM due to di/dt during switching, but the
product is designed so that 1200 V is not exceeded close to the chip when the main power source is
used at VDC(surge) or lower between the P and N main terminals.
• In order for the maximum surge voltage at the time of switching not to exceed the rated voltage, keep
the connecting wires between the IPM and the embedded product short and install a snubber close to
the P and N terminals.
1.2 External noise
Countermeasures have been taken against external noise within the IPM, but faulty operation may
possibly occur depending on the type and intensity of the noise.
Please take sufficient countermeasures against noise entering the IPM.
1.2.1 Noise from outside the equipment
• Apply a noise filter on the AC line, isolate the ground and so on.
• When required, add capacitors of 100 pF or less between all phase signal inputs and signal GND.
• Install arresters against lightning surges, etc.
6-2
Chapter 6 Precautions for Use
1.2.2 Noise from within the equipment
• Outside the rectifier: Implement the same countermeasures as the above.
• Inside the rectifier: Apply snubber circuits on the PN lines.
(In case of multiple inverters connected to one rectifier converter, etc.)
1.2.3 Noise from the output terminals
• Take external countermeasures so that contactor switching surges and so on do not enter.
2
Control Power Source
2.1 Voltage range
• The drive circuit shows stable operation when the control power source voltage is in the range of 13.5 to
16.5 V.
Operation with a value as close to 15 V as possible is recommended.
• When the control power source voltage is below 13.5 V, the loss will increase and noise will show a
tendency to decrease.
Also, the protection performance will shift, so that the protection functions may not be sufficient and chip
damage may occur.
• When the control power source voltage drops below 13.5 V, dropping down to VUV or lower, the
undervoltage protection function (UV) operates.
When the control power source voltage recovers to VUV + VH, UV is automatically released.
• When the control power source voltage exceeds 16.5 V, the loss decreases and noise shows a
tendency to increase.
Also, the protection performance will shift, so that the protection functions may not be sufficient and chip
damage may occur.
• When the control power source voltage is below 0 V (reverse bias) or exceeds 20 V, the drive circuit
and/or the main chip may be damaged. Never apply these voltages.
2.2 Voltage ripple
• The recommended voltage range of 13.5 to 16.5 V includes the voltage ripple of Vcc.
During the manufacture of the control power source, be sure to keep the voltage ripple sufficiently low.
Also be sure to keep noise superimposed on the power source sufficiently low.
• Design the control power source so as to keep dv/dt at 5 V/µs or lower.
2.3 Power source start-up sequence
• Apply the main power source after confirming that Vcc is in the recommended voltage range.
If the main power source is applied before the recommended voltage is reached, the chip may be
destroyed (worst-case scenario).
6-3
Chapter 6 Precautions for Use
2.4 Alarm at the time of power source start-up and shutdown
• At the time of power source start-up, an alarm is output at the UV protection function operation level
voltage.
Recovery is made when the protection release level voltage is reached, but as the alarm will not be
released as long as an ON signal is input, appropriate measures must be taken on the drive circuit side.
• As there is also alarm output at the time of power source shutdown, similar measures are required.
2.5 Precautions upon control circuit design
• Design with sufficient margin, taking the current consumption specification (Icc) for the drive circuit into
consideration.
• Make the wiring between the input terminals of the IPM and the photocoupler as short as possible, and
use a pattern layout with a small stray capacitance for the primary side and the secondary side of the
photocoupler.
• Install a capacitor as close as possible between Vcc and GND in the case of a high-speed photocoupler.
• For a high-speed photocoupler, use a high CMR type in which tpHL, tpLH ≤ 0.8 µs.
• For the alarm output circuit, use a low-speed photocoupler type in which CTR ≥ 100%.
• Use four isolated power sources for the control power source Vcc. Also use a design with suppressed
voltage fluctuations.
• When a capacitor is connected between the input terminals and GND, note that the response time in
regard to an input signal on the primary side of the photocoupler becomes longer.
• Design the primary-side current of the photocoupler with sufficient margin taking the CTR of the
photocoupler being used into consideration.
3
Protection Functions
As the built-in protection functions and the presence or absence of alarm output differ according to the
package and the model, confirm the protection functions of your IPM referring to the "List of IPM built-in
functions" in chapter 3.
3.1 Protection operations in general
3.1.1 Range of protection
• The protection functions included in the IPM are designed for non-repetitive abnormal phenomena.
• Do not apply constant stress that exceeds the rating.
3.1.2 Countermeasures for alarm output
• If an alarm is output, stop the input signal into the IPM immediately to stop the equipment.
• The IPM protection functions protect against abnormal phenomena, but they cannot remove the causes
of the abnormalities. After stopping the equipment, restart it after you have removed the cause of the
abnormality.
6-4
Chapter 6 Precautions for Use
3.2 Precautions for the protection functions
3.2.1 Overcurrent
• The overcurrent protection function (OC) executes a soft shutdown of the IGBT and outputs an alarm
when the overcurrent continues in excess of the insensitive time (tdoc).
Accordingly, OC does not operate when the overcurrent is removed within the tdoc period.
• In P619, the current is detected on the N-line, so there is no OC for the upper arm.
3.2.2 Starting with load short-circuit
• The OC has an insensitive time (tdoc) of approximately 5 to 10 µs. If the input signal pulse width is
shorter than this, the OC does not operate.
• If an input signal pulse width of tdoc or less continues when starting with the load shorted, short circuits
occur continuously and the chip temperature of the IGBT rises rapidly.
In such a case, the rise of the case temperature does not follow the rise of the chip temperature and the
case temperature overheating protection function (TcOH) does not operate. Normally the chip
temperature overheating protection function (TjOH) operates and provides protection, but as TjOH also
has a delay of approximately 1 ms, depending on the state of the chip temperature rise, the protection
operation may not occur in time, possibly causing damage to the chip.
3.2.3 Ground short
• If a ground short occurs and an overcurrent flows through the lower arm of the IGBT, overcurrent
protection by OC occurs for all IPMs.
• If a ground short occurs and an overcurrent flows through the upper arm of the IGBT, the protection
operation differs according to the package and the model.
P621, P622
Overcurrent protection is provided by the OC of the upper arm. Alarm output also is provided.
P610, P611, P612
Overcurrent protection is provided by the OC of the upper arm, but there is no alarm output.
For details, refer to the related document MT6M3046 "Protection in R-IPM Earth Fault Mode".
P619, P617
As there is no OC for the upper arm, there is no overcurrent protection and no alarm output.
3.3 FWD overcurrent protection
• FWD current is not detected. Accordingly, there is no protection when overcurrent flows only for FWD.
3.4 Case temperature protection
• TcOH is the protection function used when the temperature of the entire insulation substrate rises.
Accordingly, the chip temperature protection function (TjOH) operates when the heating is concentrated
on one chip.
6-5
Chapter 6 Precautions for Use
3.5 Chip temperature protection
• A chip temperature protection function (TjOH) is built into all IGBTs, including the brake part.
4
Power Cycling Capability
The lifetime of semiconductor products is not eternal. Accumulated fatigue by thermal stress resulting
from rising and falling temperatures generated within the device may shorten the lifetime of the
components. Narrow the range of temperature variations as much as possible.
5
Other
5.1 Precautions for usage and installation into equipment
(1) Also read the IPM delivery specifications for IPM use and installation into the device.
(2) Always prevent secondary damage by installing a fuse or a circuit breaker with a suitable capacity
between the commercial power source and this product, keeping in mind the possibility of chip
damage caused by unexpected accidents.
(3) When investigating the chip duty at the time of a normal turn-off operation, make sure that the
operation track for the turn-off voltage and current is within the RBSOA specifications.
When investigating the chip duty with non-repetitive short-circuit interruption, make sure that it is
within the SCSOA specifications.
(4) Use this product upon full understanding of the product usage environment and upon investigation of
whether the product reliability life is satisfactory or not. In case of use in excess of the reliability life of
the product, the chip may be destroyed before the target life of the device.
(5) Apply a thermal compound or the like between the IPM and the heat sink to make the contact heat
resistance as small as possible.
(6) Use the IPM within the range specified in the specifications for the screw torque and the heat sink
flatness.
Incorrect handling can cause insulation failure.
(7) Take care so that no load is placed on the IPM. Particularly, the control terminal should not be bent.
(8) Do not perform soldering by reflow on the main terminal and control terminal. Take care to prevent
any effect on the IPM by heat, flux, and washing solutions used for soldering other components.
(9) Avoid locations where corrosive gases are generated or dust is present.
(10) Take care to prevent high-voltage static electricity entering the main terminal and control terminal.
(11) When removing and attaching the control circuit and the IPM, first confirm that Vcc is 0 V.
6-6
Quality is our message
Chapter 7
Trouble Shooting
Contents
Page
1. Troubleshooting................................................................................................7-2
2. Fault Analysis Diagrams...................................................................................7-2
3. Alarm Cause Analysis Diagram ........................................................................7-8
7–1
Chapter 7 Troubleshooting
1
Trouble Shooting
In comparison to standard modules, IPMs have various protection functions (overcurrent, overheating,
etc.) built in, so that their devices are not easily destroyed by abnormal conditions. However, destruction
may occur depending on the abnormality, so that countermeasures are required once the cause and state
of occurrence have been clarified. An analysis diagram indicating the cause of destruction is shown on
page 2 and should be used to investigate the causes of destruction.
(For element fault judgment, refer to the Module Application Manual, chapter 4, item 2 "Fault Judgment
Method".)
Also, in the case of alarm output from the IPM, use the alarm cause analysis diagrams of Fig. 7-2 to
investigate the cause.
2
Fault Analysis Diagrams
Destruction of
IGBT part
RBSOA
IPM destruction
A
B
C
D
E
F
deviation
Gate
overvoltage
Excessive junction
temperature rise
Destruction of
FWD part
Destruction of
control circuits
Reliability
degradation
Fig. 7-1 (a.) IPM Fault Analysis Diagram (The letters A to F connect to the following diagrams.)
7-2
Chapter 7 Troubleshooting
A RBSOA deviation
[Estimated trouble location]
Excessive
shutdown current
ꢀUpper and lower
arm short-circuit
Faulty operation of
Control PCB fault
input signal circuit
ꢀExcessive turn-off current
Insufficient dead time
Control PCB fault
Abnormal load
Abnormal load
Output short-circuit
Earth fault
Excessive power source
voltage
Abnormal input
voltage
Overvoltage
ꢀMotor regenerative
Regenerative circuit
fault
operation
No overvoltage protection
operation
Control PCB fault
ꢀInsufficient snubber
Snubber resistor wire
break
Snubber circuit fault
discharge
Off operation at the
time of short-circuit
Gate drive circuit fault
Control PCB fault
Excessive surge voltage (FWD)
at the time of reverse recovery
D
Fig. 7-1 (b) Mode A: RBSOA Deviation
B Gate overvoltage
[Estimated trouble location]
Control power
source overvoltage
Excessive power source
voltage
Control power source circuit
fault
Spike voltage
Power source wiring fault
Capacitor fault
Fig. 7-1 (c) Mode B: Gate Overvoltage
7-3
Chapter 7 Troubleshooting
C
Excessive junction temperature rise (rapid temperature rise)
[Estimated trouble location]
Steady loss
increase
Increase of saturation
voltage VCE(sat)
Insufficient control power
source voltage
Gate drive circuit fault
Control power source
circuit fault
Collector current
increase
Input signal circuit
Control PCB fault
erroneous operation
Upper and lower arm short-circuit
(repeated short-circuit)
Overcurrent
Insufficient dead time
Control PCB fault
Abnormal load
Output short-circuit
(repeated short-circuit)
Ground short
(repeated ground short)
Abnormal load
Overload
Control PCB fault
Abnormal load
Switching loss
increase
Switching frequency
increase
Carrier frequency increase
Control PCB fault
Input signal faulty operation
Control PCB fault
Input circuit fault
Input circuit fault
(oscillation)
Insufficient power
source voltage
Turn-on loss increase
Turn-off loss increase
Turn-on time increase
Excessive
turn-on current
Upper and lower arm
short-circuit
Insufficient dead time
Control PCB fault
Snubber circuit fault
Control PCB fault
Control PCB fault
Large surge voltage
Excessive
turn-off current
Upper and lower arm
short-circuit
Input signal circuit
erroneous operation
Insufficient dead time
Contact heat resistance
increase
Insufficient element
tightening
Insufficient tightening
torque
Large fin bending
Fin bending fault
Insufficient compound
quantity
Insufficient thermal compound quantity
Heat sink clogging
Decrease of cooling
performance
Insufficient dust protection
measures
Case temperature rise
Drop of cooling fan
speed or stop of fan
Defective cooling fan
Abnormal rise of
ambient temperature
Local overheating of
stack
Defective cooling system
Fig. 7-1 (d) Mode C: Excessive Rise in Junction Temperature
7-4
Chapter 7 Troubleshooting
D Destruction of FWD part
[Estimated trouble location]
Excessive rise in
Steady loss increase
Overload
Power factor drop
junction temperature
Abnormal load
Control PCB fault
Switching frequency
increase
Switching loss increase
Input signal
abnormal operation
Control PCB fault
Input signal circuit fault
Control PCB fault
Carrier frequency
increase
Contact thermal resistance
increase
Insufficient element
tightening force
Insufficient tightening torque
Fin bending fault
Large fin bending
Insufficient thermal
compound quantity
Insufficient compound quantity
Insufficient dust protection
Drop of cooling
performance
Case temperature rise
Heat sink clogging
measures
Drop of cooling fan speed
Defective cooling fan
or stop of fan
Abnormal rise of
ambient temperature
Local overheating
of stack
Defective cooling system
Excessive surge voltage at
time of reverse recovery
Overvoltage
Snubber circuit fault
di/dt increase at time
of turn-on
Control power source
voltage increase
Control power source circuit fault
Minute pulse reverse
recovery phenomenon
Gate signal breaking
by noise etc.
Control power source circuit fault
Control PCB fault
Excessive surge voltage at
time of IGBT turn-off
A
Excessive charging current to
converter part at time of use
Overcurrent
Charging circuit fault
Fig. 7-1 (e) Mode D: Destruction of FWD Part
7-5
Chapter 7 Troubleshooting
E Destruction of control circuits
[Estimated trouble location]
Excessive control power
Overvoltage
Control power source circuit fault
source voltage
Power source stabilization
Capacitor fault
Spike voltage
Long power source wiring
Control voltage application status
desorption
Excessive input part voltage
Excessive static electricity
Control circuit fault
Insufficient antistatic measures
Abnormal input pull-up resistance
Input part overcurrent
Fig. 7-1 (f) Mode E: Destruction of Control Circuit
7-6
Chapter 7 Troubleshooting
F Damage related to reliability and product handling
Product loading
at time of storage
Destruction from handling
External force, load
Loading conditions
Stress at element at time of
mounting
Stress of the terminal part
Screw length
Too long screws used for main terminals
and control terminals
Excessive tightening torque
Tightening part
Terminal part
Insufficient tightening force for
main terminal screws
Excessive contact resistance
Main terminal part
Excessive vibration at time of
transport (product, equipment)
Vibration
Transport conditions
Insufficient fixing of parts at
time of product mounting
Product terminal part (check
for stress from vibration)
Dropping, impact, etc. at time
of transport
Impact shock
Transport conditions
Thermal resistance of soldered
terminals
Overheating at time of
terminal soldering
Assembly conditions at the
time of product mounting
Storage under abnormal
conditions
Storage in corrosive
atmosphere
Storage conditions
Storage in atmosphere where
condensation occurs easily
Storage in environment with
excessive dust
Reliability (life)
degradation
Storage at high temperature
(exposure to high temperatures)
Long-term storage at high
temperatures
Storage conditions
Storage at low temperatures
Long-term storage at low
temperatures
*
For the results of the
(exposure to low temperatures)
reliability tests performed
by Fuji Electric Device
Technology, refer to the
specifications and the
reliability test result report.
Excessive humidity
(exposure to humidity)
Long-term storage at high
temperature and high
Thermal stress fatigue from repeated gentle rise and fall of product temperature
Matching of application
conditions and product life
(temperature cycle, ∆Tc power cycle)
Thermal stress failure from rapid rise or fall of product temperature (thermal impact)
Thermal stress failure of wiring in product, etc., caused by change of semiconductor chip
temperature because of rapid load changes etc. (∆Tj power cycle)
Long-time voltage application under high temperature (high
temperature application (between C and E or G and E))
Long-term use at high
temperatures
Long-time voltage application at high temperature and
high humidity (application under moisture (THB))
Long-term use at high
humidity
Long-term use in atmosphere
of hydrogen sulfide, etc.
Use in a corrosive gas atmosphere
Fig. 7-1 (g) Mode F: Damage Related to Reliability and Product Handling
7-7
Chapter 7 Troubleshooting
3
Alarm Cause Analysis Diagram
3.1 Cause analysis in the event an IPM alarm occurs
When an inverter using an IPM comes to an alarm stop, a survey must first be done to find out whether
the alarm was output from the IPM or from a device control circuit (other than the IPM).
If the alarm was output by the IPM, determine the cause according to the following cause analysis
diagram.
For observation of whether there is an IPM alarm or not via the alarm output voltage, the presence or
absence of an alarm output can be confirmed easily by inserting a 1.5 kΩ resistor between the IPM alarm
terminal and the cathode of the alarm photodiode and measuring the IPM alarm terminal voltage.
Phenomenon
Explanation of alarm cause
How to determine alarm cause
IPM alarm occurrence
Normal alarm
Measure the control power source voltage Vcc,
the DC input voltage d, the output current Io.
Measure the case temperature Tc directly under
TjOH
OC
The chip temperature Tj is detected by the
temperature detection element (diode) built
into all IGBTs.
•
•
•
•
the chip, calculate Tj-c, and estimate Tj.
When TjOH exceeds the trip level
continuously for 1 ms or longer, the IGBT is
switched off for protection.
∆
Confirm the IPM installation method.
(Fin flatness, thermal compound, etc.)
The alarm holding time in many cases is longer
than 2 ms.
Observe the alarm and the output current (U, V,
W) with an oscilloscope.
The collector current is detected by the
current flowing through the current sensing
IGBT built into all IGBT chips.
•
•
•
•
•
Observe the alarm and the DC input current (P, N)
with an oscilloscope.
When the overcurrent trip level is exceeded
Observe the current change 5 s before alarm
continuously for approximately 5 s or longer,
µ
µ
output.
the IGBT is switched off for protection.
Confirm the trip level and the detection location in
case of current detection with CT, etc.
The alarm holding time in many cases is 2 ms.
Observe the alarm and Vcc with an oscilloscope.
UV
When the control power source voltage Vcc
drops below the undervoltage trip level
•
•
Observe the power source voltage change 5
before alarm output
s
µ
continuously for 5 s or longer, the IGBT is
µ
In case of instantaneous voltage drops, the alarm
holding time in many cases is 2 ms.
switched off for protection.
•
Measure the temperature at the side of the
copper base with a thermocouple.
Observe the alarm output period with an
oscilloscope.
TcOH
The insulation substrate temperature is
detected by the temperature detection
element (IC) installed on the same ceramic
substrate as the power device.
•
•
•
The possibility that the alarm is TcOH is large
when output is made for a longer period than the
2 ms of the alarm holding time.
When the TcOH trip level is exceeded
continuously for 1 ms or longer, the IGBT is
switched off for protection.
Faulty alarm
A short pulse alarm in the order of s is output.
When the control power source voltage Vcc
•
•
µ
•
Observe the Vcc waveform during motor
operation with an oscilloscope, preferably in the
vicinity of the IPM control terminals.
exceeds the absolute max. rating of 20 V or
when an excessive dv/dt or ripple is
applied, the drive IC may be damaged or a
faulty alarm output.
Vcc < 20 V, dv/dt 5 V/ s, and Vripple 2 Vp-p
•
•
≤
µ
≤
shall apply (all four power supplies).
When noise current flows in the IPM control
•
Confirm that there is no external wiring between
IPM control GND and main terminal GND. In case
of wiring, noise current flows into the IPM control
circuit.
circuit, the IC voltage may become unstable
and a faulty alarm output.
When the drive IC is damaged, there is a high
possibility of abnormal increase of Icc.
•
Ex.: If Iccp 10 mA @Vin = "High", confirm the
≥
abnormality of IPM peripheral circuits.
Refer to "Cautions for Design and Application" and
"Application Circuit Examples" in the delivery
specifications.
Fig. 7-2 Alarm Cause Analysis Diagram
7-8
相关型号：
7MBP80RTB060
Insulated Gate Bipolar Transistor, 80A I(C), 600V V(BR)CES, N-Channel, P610, 22 PIN
FUJI
©2020 ICPDF网 联系我们和版权申明