MC33291LDWR2 [FREESCALE]
Eight-Output Switch with Serial Peripheral Interface I/O; 八个输出开关，串行外设接口I / O
| 型号： | MC33291LDWR2 |
| 厂家： | 
Freescale |
| 描述： | Eight-Output Switch with Serial Peripheral Interface I/O |
| 文件： | 总26页 (文件大小：1285K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
Document Number: MC33291L
Rev. 5.0, 9/2008
Freescale Semiconductor
Technical Data
Eight-Output Switch with Serial
Peripheral Interface I/O
33291L
The 33291L device is an eight-output, low-side power switch with 8-
bit serial input control. The 33291L is a versatile circuit designed for
automotive applications, but is well suited for other environments. The
33291L incorporates SMARTMOS technology, with CMOS logic,
bipolar/MOS analog circuitry, and DMOS power MOSFETs. The
33291L interfaces directly with a microcontroller to control various
inductive or incandescent loads.
LOW-SIDE SWITCH
The circuit’s innovative monitoring and protection features include
very low standby current, SPI cascade fault reporting capability,
internal 53 V clamp on each output, output-specific diagnostics, and
independent shutdown of outputs.
DW SUFFIX
EG SUFFIX (PB-FREE)
98ASB42344B
The device is parametrically specified over an ambient temperature
range of -40°C ≤ TA ≤ 125°C and 9.0 V ≤ VPWR ≤ 16 V supply.
24-PIN SOICW
Features
ORDERING INFORMATION
• Designed to Operate Over Wide Supply Voltages of 5.5 V to 26.5 V
• Interfaces to Microprocessor Using 8-Bit SPI I/O Protocol up to 3.0
MHz
Temperature
Package
Device
Range (T )
A
• 1.0 A Peak Current Outputs with Maximum RDS(ON) of 1.6 Ω at TJ -
150°C
• Outputs Current-Limited to Accommodate In-Rush Currents
Associated with Switching Incandescent Loads
• Output Voltages Clamped to 53 V During Inductive Switching
• Maximum Sleep Current (IPWR) of 25 μA
MC33291LDW/R2
MCZ33291LEG/R2
-40°C to 125°C
24 SOICW
• Maximum of 4.0 mA IDD During Operation
• Pb-Free Packaging Designated by Suffix Code EG
V
V
DD
PWR
33291L
VPWR
OP 0
OP 1
OP 2
OP 3
OP 4
OP 5
OP 6
OP 7
GND
SFPD
VDD
CS
SCLK
SI
MCU
SO
RESET
Figure 1. 33291L Simplified Application Schematic
Freescale Semiconductor, Inc. reserves the right to change the detail specifications, as
may be required, to permit improvements in the design of its products.
© Freescale Semiconductor, Inc., 2007 - 2008. All rights reserved.
VPWR
21
Output 0
24
Over-
voltage
Voltage
Regulator
Bias
+
53 V
PIN
16
15
GE
OVD
OT
SF
OF
Gate
Control
V
SFPD
DD
RB
10 μA
To Gates
1–7
Outputs
SFPD
SFL
CS
RST
25 μA
1, 2, 11–14, 23
22
+
Open
Load
SPI
SCLK
SI
Interface
Logic
Detect
CS
10 μA
SO
lLimit
10
SCLK
CSI
CSBI
Fault Timers
+
-
R
S
Short
Circuit
Detect
+
10 μA
3
SI
10 μA
Grounds
Over-
temperature
Detect
4
9
5–8, 17–20
SO
Serial D/O
Line Driver
From Detectors 1–7
Figure 2. 33291L Simplified Block Diagram
Table 1. Fault Operation
SERIAL OUTPUT (SO) PIN REPORTS
Overvoltage condition reported.
Fault reported by Serial Output (SO) pin.
Overvoltage
Overtemperature
SO pin reports short to battery/supply or overcurrent condition.
Not reported.
Overcurrent
Output ON, Open Load Fault
Output OFF, Open Load Fault
DEVICE SHUTDOWNS
Overvoltage
SO pin reports output OFF open load condition.
Total device shutdown at V
= 28 V to 36 V. All outputs are latched off while the SPI register is reset
PWR
(cleared). Outputs can be turned back on with a new SPI command after V
has decayed below 26.5 V.
PWR
Only the output experiencing an overtemperature condition turns OFF.
Overtemperature
Overcurrent
Only the output experiencing an overcurrent shuts down at 1.0 A to 3.0 A after a 70 μs to 250 μs delay, with
SFPD pin grounded. All other outputs will continue to operate in a current limit mode with no shutdown if the
SFPD pin is at 5.0 V (so long as the individual outputs are not experiencing thermal limit conditions).
33291L
Analog Integrated Circuit Device Data
Freescale Semiconductor
2
PIN CONNECTIONS
PIN CONNECTIONS
1
24
23
22
21
20
19
18
17
16
15
14
13
OP7
OP6
SCLK
SI
OP0
2
OP1
3
RST
4
VPWR
GND
GND
GND
GND
VDD
SFPD
OP2
5
GND
GND
GND
GND
SO
6
7
8
9
10
11
12
CS
OP5
OP4
OP3
Figure 3. 33291L Pin Connections
Table 2. 33291L Pin Definitions
PIN
PIN NAME
FORMAL NAME
DEFINITION
NUMBER
Connection to drain of output MOSFET number seven.
Connection to drain of output MOSFET number six.
Clocks the internal Shift registers of the 33291L.
1
2
3
4
OP7
OP6
SCLK
SI
Output 7
Output 6
System Clock
Serial Input
This pin is for the input of serial instruction data. SI information is read on the falling
edge of SCLK.
Connection to IC Power Ground and functions as part of heat sinking path.
Tri-stateable output from the Shift register.
5–8, 17–20
GND
SO
Ground
9
Serial Output
Chip Select
Whenever this pin is in a logic low state, data can be transferred from the MCU to
the 33291L through the SI pin and from the 33291L to the MCU through the SO pin.
10
CS
Connection to drain of output MOSFET number five.
Connection to drain of output MOSFET number four.
Connection to drain of output MOSFET number three.
Connection to drain of output MOSFET number two.
11
12
13
14
15
OP5
OP4
Output 5
Output 4
Output 3
Output 2
OP3
OP2
This pin is used to prevent the outputs from latching-OFF because of an overcurrent
condition.
SFPD
Short Fault
Protect Disable
Plus supply for logic.
Main power supply.
16
21
V
Logic Supply
DD
VPWR
Output MOSFET
Gate Drive Supply
This pin is active low. It is used to clear the SPI Shift register, thereby setting all
output switches OFF.
22
RST
Reset
Connection to drain of output MOSFET number one.
Connection to drain of output MOSFET number zero.
23
24
OP1
OP0
Output 1
Output 0
33291L
Analog Integrated Circuit Device Data
Freescale Semiconductor
3
ELECTRICAL CHARACTERISTICS
MAXIMUM RATINGS
ELECTRICAL CHARACTERISTICS
MAXIMUM RATINGS
Table 3. Maximum Ratings
All voltages are with respect to ground unless otherwise noted. Exceeding these ratings may cause a malfunction or
permanent damage to the device.
Rating
Symbol
Value
Unit
Power Supply Voltage
V
Normal Operation (Steady-State)
Transient Conditions (1)
V
V
-1.5 to 26.5
-13 to 60
PWR(SUS)
PWR(PK)
Logic Supply Voltage (2)
Input Pin Voltage (3)
V
-0.3 to 7.0
-0.3 to 7.0
V
V
V
DD
V
IN
Output Clamp Voltage (4)
V
OUT(OFF)
5.0 mA ≤ I
≤ 0.5 A
45 to 65
OUT
Output Self-Limit Current
Continuous Per Output Current (5)
ESD Voltage (6) (7)
I
1.0 to 3.0
500
A
mA
V
OUT(LIM)
I
OUT(CONT)
Human Body Model
Machine Model
V
V
±2000
±200
ESD1
ESD2
Output Clamp Energy (8)
E
50
mJ
MHz
°C
CLAMP
Recommended Frequency of SPI Operation
Storage Temperature
f
3.0
SPI
T
-55 to 150
-40 to 125
-40 to 150
2.0
STG
Operating Case Temperature
Operating Junction Temperature
Power Dissipation (TA = 25°C) (9)
T
°C
C
T
°C
J
P
W
D
Notes
1. Transient capability with external 100 Ω resistor in series with V
pin and supply.
PWR
2. Exceeding these limits may cause a malfunction or permanent damage to the device.
3. Exceeding the limits on SCLK, SI, CS, SFPD, or RST pins may cause permanent damage to the device.
4. With output OFF.
5. Continuous output current rating so long as maximum junction temperature is not exceeded. Operation at 125°C ambient temperature
will require maximum output current computation using package R
θJA.
6. ESD data available upon request.
7. ESD1 testing is performed in accordance with the Human Body Model (C
= 200 pF, R
= 1500 Ω), ESD2 testing is performed in
ZAP
ZAP
accordance with the Machine Model (C
= 200pF, R
= 0 Ω).
ZAP
ZAP
8. Maximum output clamp energy capability at 150°C junction temperature using a single non-repetitive pulse method.
9. Maximum power dissipation at indicated junction temperature with no heat sink used.
33291L
Analog Integrated Circuit Device Data
Freescale Semiconductor
4
ELECTRICAL CHARACTERISTICS
MAXIMUM RATINGS
Table 3. Maximum Ratings (continued)
All voltages are with respect to ground unless otherwise noted. Exceeding these ratings may cause a malfunction or
permanent damage to the device.
Rating
Peak Package Reflow Temperature During Reflow (10)
Thermal Resistance
Symbol
TPPRT
R
Value
Unit
(11)
°C
,
Note 11.
°C/W
JA
θ
All Outputs ON(12)
Single Output ON(13)
60
45
Notes
10. Pin soldering temperature limit is for 10 seconds maximum duration. Not designed for immersion soldering. Exceeding these limits may
cause malfunction or permanent damage to the device.
11. Freescale’s Package Reflow capability meets Pb-free requirements for JEDEC standard J-STD-020C. For Peak Package Reflow
Temperature and Moisture Sensitivity Levels (MSL),
Go to www.freescale.com, search by part number [e.g. remove prefixes/suffixes and enter the core ID to view all orderable parts. (i.e.
MC33xxxD enter 33xxx), and review parametrics.
12. Junction temperature is a function of die size, on-chip power dissipation, package thermal resistance, mounting site (board)
temperature, ambient temperature, air flow, power dissipation of other components on the board, and board thermal resistance.
13. Per SEMI G38-87 and JEDEC JESD51-2 with the single layer board (JESD51-3) horizontal.
33291L
Analog Integrated Circuit Device Data
Freescale Semiconductor
5
ELECTRICAL CHARACTERISTICS
STATIC ELECTRICAL CHARACTERISTICS
STATIC ELECTRICAL CHARACTERISTICS
Table 4. Static Electrical Characteristics
Characteristics noted under conditions 4.5 V ≤ VDD ≤ 5.5 V, 9.0 V ≤ VPWR ≤ 16 V, -40°C ≤ TA ≤ 125°C, unless otherwise noted.
Typical values noted reflect the approximate value with VBAT = 13 V, TA = 25°C.
Characteristic
Symbol
Min
Typ
Max
Unit
POWER INPUT
Supply Voltage Range
V
Quasi-Functional (14)
Fully Operational
V
5.5
9.0
–
–
9.0
PWR(QF)
V
V
26.5
PWR(FO)
Supply Current (All Outputs ON, I
= 0.5 A)
–
–
1.0
1.0
1.0
32
0.8
–
2.0
2.5
2.5
36
mA
μA
μA
V
OUT
PWR(ON)
PWR(ON)
Sleep State Supply Current at RST ≤ 0.2 V
and/or V
< 0.5 V
DD
I
DD
Sleep State Output Leakage Current (Per Output, RST = 0 V)
I
–
PWR(SS)
Overvoltage Shutdown
V
28
0.2
4.5
OV
OV(HYS)
Overvoltage Shutdown Hysteresis (15)
Logic Supply Voltage
V
1.5
5.5
V
V
V
DD
Logic Supply Current (16)
I
DD
RST ≥ 0.7 V
–
–
1.0
–
4.0
25
mA
DD
RST ≤ 0.5 V
μA
Logic Supply Undervoltage Lockout Threshold (17)
V
2.5
–
3.5
V
(UVLO)
DD
POWER OUTPUT
Drain-to-Source ON Resistance (I
= 0.5 A, T - 25°C)
Ω
OUT
OUT
J
RDS(ON)
V
V
V
= 5.5 V
= 9.0 V
= 13 V
–
–
–
–
2.0
1.6
1.4
PWR
PWR
PWR
1.2
1.1
Drain-to-Source ON Resistance (I
= 0.5 A, T - 150°C)
Ω
J
RDS(ON)
V
V
V
= 5.5 V
= 9.0 V
= 13 V
–
–
–
–
3.0
2.0
1.6
PWR
PWR
PWR
1.2
1.0
Output Self-Limiting Current
Outputs Programmed ON, V
I
A
V
OUT(LIM)
= 0.6 V
1.0
2.0
3.0
OUT
DD
Output Fault Detect Threshold (18)
Output Programmed OFF
V
OUTth(F)
2.5
30
3.0
50
3.5
Output OFF Open Load Detect Current (19)
μA
I
OCO
Output Programmed OFF, V
= 0.6 V
100
OUT
DD
Notes
14. SPI inputs and outputs operational. Fault status reporting may not be fully operational within this voltage range. Outputs remain
operational somewhat below this V range, but R will increase, causing power dissipation to increase. Outputs will re-
PWR
DS(ON)
establish their instructed state following a V
interruption as long as V
remains non-interrupted.
PWR
DD
15. This parameter is guaranteed by design, but it is not production tested.
16. Measured with the RST pin held at a logic high state. Outputs can be OFF or ON or in any combination thereof.
17. Device incorporates a power-ON reset function. For V
reset and all outputs are disabled.
less than the Undervoltage Lockout Threshold voltage, all data registers are
DD
18. Output Fault Detect Threshold with outputs programmed OFF. Output fault detect thresholds are the same for output opens and shorts.
19. Output OFF Open Load Detect Current is the current required to flow through the load for the purpose of detecting the existence of an
open load condition when the specific output is commanded to be OFF.
33291L
Analog Integrated Circuit Device Data
Freescale Semiconductor
6
ELECTRICAL CHARACTERISTICS
STATIC ELECTRICAL CHARACTERISTICS
Table 4. Static Electrical Characteristics (continued)
Characteristics noted under conditions 4.5 V ≤ VDD ≤ 5.5 V, 9.0 V ≤ VPWR ≤ 16 V, -40°C ≤ TA ≤ 125°C, unless otherwise noted.
Typical values noted reflect the approximate value with VBAT = 13 V, TA = 25°C.
Characteristic
Symbol
Min
Typ
Max
Unit
Output Clamp Voltage
2.0 mA < I < 200 mA
V
V
OK
45
53
65
OUT
Output Leakage Current (V
< 2.0 V) (20)
μA
°C
°C
I
-25
155
–
0
25
–
DD
OUT(LKG)
Overtemperature Shutdown (Outputs OFF) (21)
Overtemperature Shutdown Hysteresis (21)
DIGITAL INTERFACE
T
180
10
LIM
LIM(HYS)
T
20
Input Logic High Voltage (22)
V
V
0.7
0
–
–
1.0
0.2
500
20
20
20
50
25
–
V
V
IH
IL
DD
DD
Input Logic Low Voltage (22)
Input Logic Threshold Hysteresis (SCLK, RST, and SFPD) (23)
V
50
0
100
10
10
10
25
10
mV
μA
μA
μA
μA
μA
V
I(HYS)
SI Pull-Up Current (SI = 0 V)
I
SI
CS Pull-Up Current (CS = 0 V)
I
0
CS
SCLK Pull-Down Current (SCLK = 5.0 V)
RST Pull-Down Current (RST = 5.0 V)
SFPD Pull-Down Current (SFPD = 5.0 V)
I
0
SCLK
I
5.0
5.0
RST
I
SFPD
SO High-State Output Voltage (I
= 1.0 mA)
V
V
-0.4 V
V
- 0.2 V
DD
OH
SOH
DD
SO Low-State Output Voltage (I = -1.6 mA)
OL
V
–
-10
–
0.2
0
0.4
10
12
20
V
SOL
SO Tri-State Leakage Current (CS = 0.7 VDD, 0 V < V
< V
)
DD
I
μA
pF
pF
SO
SOT
Input Capacitance (0 V < V
< 5.5 V) (24)
C
–
DD
IN
SO Tn-State Capacitance (0 V < V < 5.5 V) (25)
C
–
–
DD
SOT
Notes
20. Output leakage current measured with the output OFF and at 16 V.
21. This parameter is guaranteed by design, but it is not production tested.
22. Upper and lower logic threshold voltage levels apply to SI, CS, SCLK, RST, and SFPD inputs.
23. Hysteresis is characterized, but it is not production tested.
24. Input capacitance of SI CS, SCLK, RST, and SFPD for 0 V < V < 5.5 V. This parameter is guaranteed by design, but it is not production
DD
tested.
25. Tri-state capacitance of SO for 0 V < V
< 5.5 V. This parameter is guaranteed by design, but it is not production tested.
DD
33291L
Analog Integrated Circuit Device Data
Freescale Semiconductor
7
ELECTRICAL CHARACTERISTICS
DYNAMIC ELECTRICAL CHARACTERISTICS
DYNAMIC ELECTRICAL CHARACTERISTICS
Table 5. Dynamic Electrical Characteristics
Characteristics noted under conditions 4.5 V ≤ VDD ≤ 5.5 V, 9.0 V ≤ VPWR ≤ 16 V, -40°C ≤ TA ≤ 125°C, unless otherwise noted.
Typical values noted reflect the approximate parameter mean at TA = 25°C under nominal conditions, unless otherwise noted.
Characteristic
Symbol
Min
Typ
Max
Unit
POWER OUTPUT TIMING
Output Rise Time (V
PWR
= 13 V, R = 26 Ω) (26)
t
r
0.4
0.4
1.0
1.0
5.0
5.0
15
20
20
50
50
μs
μs
μs
μs
μs
L
Output Fall Time (V
= 13 V, R = 26 Ω) (26)
t
f
PWR
L
Output Turn-ON Delay Time (V
= 13 V, R = 26 Ω) (27)
t
PWR
L
dly(on)
Output Turn-OFF Delay Time (V
= 13 V, R = 26 Ω) (28)
t
15
PWR
L
dly(off)
Output Short Fault Disable Report Delay (29)
t
dly(sf)
SFPD = 0.2 x V
DD
70
70
150
150
250
250
Output OFF Fault Report Delay (30)
t
μs
dly(off)
SFPD = 0.2 x V
DD
DIGITAL INTERFACE TIMING
(31)
Required Low State Duration for RST (V < 0.2 V
)
DD
t
–
–
–
–
–
–
–
–
–
–
–
50
50
50
25
25
25
25
–
167
167
167
83
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
IL
w(RST)
Falling Edge of CS to Rising Edge of SCLK (Required Setup Time)
Falling Edge of SCLK to Rising Edge of CS (Required for Setup Time)
SI to Falling Edge of SCLK (Required for Setup Time)
t
lead
t
lag
t
SI(su)
Falling Edge of SCLK to SI (Required for Hold Time)
t
83
SI(hold)
SO Rise Time (C = 200 pF)
L
t
50
r(SO)
SO Fall Time (C = 200 pF)
L
t
50
f(SO)
SI, CS, SCLK, Incoming Signal Rise Time (32)
t
50
r(SI)
SI, CS, SCLK, Incoming Signal Fall Time (32)
t
–
50
f(SI)
Time from Falling Edge of CS to SO Low Impedance (33)
Time from Rising Edge of CS to SO High Impedance (34)
Time from Rising Edge of SCLK to SO Data Valid (35)
t
–
110
110
SO(en)
t
–
SO(dis)
t
valid
0.2 V
≤ SO ≥ 0.8 V , C = 200 pF
DD L
–
65
105
DD
Notes
26. Output Rise and Fall time respectively measured across a 26 Ω resistive load at 10% to 90% and 90% to 10% voltage points.
27. Output Turn-ON Delay time measured from 50% rising edge of CS to 90% of Output OFF voltage (V
) with R = 26 Ω resistive load.
PWR
L
28. Output Turn-OFF Delay time measured from 50% rising edge of CS to 10% of Output OFF voltage (V
) with R = 26 Ω resistive load.
PWR
L
29. Propagation time of Short Fault Disable Report measured from 50% rising edge of CS to 10% Output OFF voltage (V
), V
=
PWR
PWR
6.0 V and SFPD = 2.0 x V
.
DD
30. Output OFF Fault Report Delay measured from 50% rising edge of CS to 10% rising edge of Output OFF voltage (V
31. RST Low duration measured with outputs enabled and going to OFF or disabled condition.
).
PWR
32. Rise and Fall time of incoming SI, CS, and SCLK signals suggested for design consideration to prevent the occurrence of double pulsing.
33. Time required for output status data to be available for use at the SO pin.
34. Time required for output status data to be terminated at the SO pin.
35. Time required to obtain valid data out from SO following the rise of SCLK. See Figure 6, page 9.
33291L
Analog Integrated Circuit Device Data
8
Freescale Semiconductor
ELECTRICAL CHARACTERISTICS
ELECTRICAL PERFORMANCE CURVES
ELECTRICAL PERFORMANCE CURVES
tR(SI)
tF(SI)
< 50 ns
50%
< 50 ns
0.2 V
V
= 5.0 V
DD
5.0 V
0.7 V
DD
SCLK
DD
0
V
t
OH
DLY(LH)
0.7 V
DD
33291L
Under
Test
SCLK
SO
0.2 V
t
SO
(Low-to-High)
DD
V
V
OL
tR(SO)
tF(SO)
C
= 200 pF
L
VALID
SO
OH
0.7 V
(High-to-Low)
DD
0.2 V
DD
V
t
OL
DLY(HL)
SO (Low-to-High) is for an output with internal conditions such that
the low-to-high transition of CS causes the SO output to switch from
high to low.
C represents the total capacitance of the test fixture and probe.
L
Figure 4. Valid Data Delay Time and
Valid Time Test Circuit
Figure 6. Valid Data Delay Time and
Valid Time Waveforms
t
t
R(SI)
< 50 ns
F(SI)
< 50 ns
CS
SO
V
= 5.0 V
V
= 2.5 V
DD
Pull-Up
5.0 V
0
90%
V
0.7 DD
10%
0.2 V
DD
t
t
SO(EN)
90%
SO(DIS)
VTri-State
R = 1.0 kΩ
L
(High-to-Low)
33291L
Under
Test
SO
CS
10%
SO(DIS)
tSO(dis
VOH
C
= 20 pF
t
t
L
SO(EN)
10%
90%
SO
(Low-to-High)
VTri-State
1. SO (high-to-low) waveform is for SO output with internal conditions such
that SO output is low except when an output is disabled as a result of de-
tecting a circuit fault with CS in a High Logic state; e.g., open load.
2. SO (low-to-high) waveform is for SO output with internal conditions such
that SO output is high except when an output is disabled as a result of de-
tecting a circuit fault with CS in a High Logic state; e.g., shortened load.
CL represents the total capacitance of the test fixture and probe.
Figure 5. Enable and Disable Time Test Circuit
Figure 7. Enable and Disable Time Waveforms
33291L
Analog Integrated Circuit Device Data
Freescale Semiconductor
9
ELECTRICAL CHARACTERISTICS
ELECTRICAL PERFORMANCE CURVES
t
t
F(SI)
R(SI)
< 50 ns
< 50 ns
90%
5.0 V
V
= 5.0 V
V
= 14 V
PWR
DD
50%
CS
10%
0
t
DLY(OFF)
14 V
R = 26 Ω
L
Output Voltage
Waveform 1
10%
33291L
Under
Test
V
OL
CS
Output
14 V
C
L
Output Voltage
Waveform 2
90%
V
OL
t
DLY(ON)
1. t
DLY(ON)
and T
are turn-ON and turn-OFF propagation delay
DLY(OFF)
times.
2. Turn-OFF is an output programmed from an ON to an OFF state.
3. Turn-ON is an output programmed from and OFF to an ON state.
C represents the total capacitance of the test fixture and probe.
L
Figure 8. Switching Time Test Circuit
Figure 10. Turn-On/-Off Waveforms
t
t
F(SI)
V
= 5.0 V
V
= 11 V
R(SI)
DD
PWR
< 50 ns
50%
< 50 ns
5.0 V
0
90%
10%
CS
Ι
= 2.0 Α
L
(Ουτπυτ ΟΝ)
33291L
Under
Output Voltage
Waveform
V
V
= 11 V
OFF
Output
CS
50%
Test
= 5.0 V
ON
C = 20 pF
L
t
PDLY(OFF)
50%
I
O(CL)
Output Current
Waveform
0
1. t
PDLY(OFF)
is the output fault unlatch disable propagation delay time re-
C represents the total capacitance of the test fixture and probe.
L
quired to correctly report an output fault after CS rises. It represents an
output commanded ON while having an existing output short (overcurrent)
to supply.
Figure 9. Output Fault Unlatch Disable
Delay Test Circuit
2. The SFPD pin < 0.2 V.
Figure 11. Output Fault Unlatch Disable
Delay Waveforms
33291L
Analog Integrated Circuit Device Data
Freescale Semiconductor
10
FUNCTIONAL DESCRIPTION
INTRODUCTION
FUNCTIONAL DESCRIPTION
INTRODUCTION
The 33291L was conceived, specified, designed, and
developed for automotive applications. It is an eight-output
low-side power switch having 8-bit serial control. The 33291L
incorporates SMARTMOS technology having CMOS logic,
bipolar/MOS analog circuitry, and independent state of the
art double diffused MOS (DMOS) power output transistors.
Many benefits are realized as a direct result of using this
mixed technology. A simplified block diagram delineates
33291L in Figure 2.
MC68HCXX
33291
Microcontroller
MOSI
MISO
SI
Shift Register
Shift Register
SO
SCLK
Receive
Buffer
To
Where bipolar devices require considerable control
current for their operation, structured MOS devices, since
they are voltage controlled, require only transient gate
charging current affording a significant decrease in power
consumption. The CMOS capability of the SMARTMOS
process allows significant amounts of logic to be
Logic
RST
CS
Parallel
Ports
Figure 12. SPI Interface with Microcontroller
economically incorporated into the monolithic design.
Additionally, the bipolar/MOS analog circuits embedded
within the updrain power DMOS output transistors monitor
and provide fast, independent protection control functions for
each individual output. All outputs have internal 45 V at 0.5 A
independent output voltage clamps to provide fast inductive
turn-off and transient protection.
The circuit can also be used in a variety of other
applications in the computer, telecommunications, and
industrial fields. It is parametrically specified over an input
battery/supply range of 9.0 V to 16 V but is designed to
operate over a considerably wider range of 5.5 V to 26.5 V.
The design incorporates the use of logic level MOSFETs as
output devices. These MOSFETs are sufficiently turned ON
with a gate voltage of less than 5.0 V, thus eliminating the
need for an internal charge pump. Each output is identically
sized and independent in operation. The efficiency of each
output transistor is such that at room temperature with as little
as 9.0 V supply (VPWR), the maximum RDS(ON) of an output
at room temperature is 1.2 Ω (0.9 Ω typical) and increases to
only 2.0 Ω as VPWR is decreased to 5.5 V.
The 33291L uses high-efficiency updrain power DMOS
output transistors exhibiting very low room temperature
drain-to-source ON resistance values (RDS(ON) ≤ 1.0 Ω at
13 V VPWR) and dense CMOS control logic. Operational bias
currents of less than 2.0 mA (1.0 mA typical) with any
combination of outputs ON are the result of using this mixed
technology and would not be possible with bipolar structures.
To accomplish a comparable functional feature set using a
bipolar structure approach would result in a device requiring
hundreds of milliamperes of internal bias and control current.
This would represent a very large amount of power to be
consumed by the device itself and not available for load use.
All inputs are compatible with 5.0 V CMOS logic levels,
incorporating negative or inverted logic. Whenever an input is
programmed to a logic low state (<1.0 V) the corresponding
low side switched output being controlled will be active low
and turned ON. Conversely, whenever an input is
During operation, the 33291L functions as an eight output
serial switch serving as a microcontroller (MCU) bus
expander and buffer with fault management and fault
reporting features. In doing so, the device directly relieves the
MCU of the fault management functions. The 33291L directly
relieves the MCU of the fault management functions. The
33291L directly interfaces to an MCU, operating at system
clock serial frequencies in excess of 3.0 MHz. It uses a
Synchronous Peripheral Interface (SPI) for control and
diagnostic readout. Figure 12 illustrates the basic SPI
configuration between an MCU and one 33291L.
programmed to a logic high state (>3.0 V), the output being
controlled will be high and turned OFF.
One main advantage of the 33291L is the serial port.
When coupled to an MCU, it receives ON/OFF commands
from the MCU and in return transmits the drain status of the
device’s output switches. Many devices can be daisy-
chained together, forming a larger system, as illustrated in
Figure 13, page 12.
Note In this example, only one dedicated MCU parallel
port (aside from the required SPI) is required for chip select
to control 32 possible loads.
33291L
Analog Integrated Circuit Device Data
Freescale Semiconductor
11
FUNCTIONAL DESCRIPTION
INTRODUCTION
SCLK
Parallel Port
CS
SO
SCLK
SI
CS
SO
SCLK
SI
CS
SO
SCLK
SI
CS
SO
SCLK
SI
MISO
IRQ
MC68XX
Microcontroller
SPI
33291
33291
33291
33291
8 Outputs
8 Outputs
8 Outputs
8 Outputs
MOSI
Figure 13. 33291L SPI System Daisy Chain
Multiple 33291L devices can also be controlled in a
parallel input fashion using SPI, illustrated in Figure 14. This
figure shows a possible 24 loads being controlled by only
three dedicated parallel MCU ports used for chip select.
master; however, not at the same time. Only when the master
is not communicating can a slave assume the mastership and
communicate. MCU master control is switched through the
use of the slave select (SS) pin of the MCUs. A master will
become a slave when it detects a logic low state on its SS pin.
These basic examples make the 33291L very attractive for
applications where a large number of loads require efficient
control. To this end, the popular Synchronous Serial
Peripheral Interface (SPI) protocol is incorporated to
communicate efficiently with the MCU.
33291
MOSI
SI
8 Outputs
SCLK
SCLK
CS
MC68XX
Microcontroller
SPI
SPI SYSTEM ATTRIBUTES
The SPI system is flexible enough to communicate directly
with numerous standard peripherals and MCUs available
from Motorola and other semiconductor manufacturers. SPI
reduces the number of pins necessary for input/output (I/O)
on the 33291L. It also offers an easy means of expanding the
I/O function using few MCU pins. The SPI system of
33291
8 Outputs
SI
SCLK
A0
Parallel
A1
CS
Ports
A2
communication consists of the MCU transmitting, in return it
receives one data-bit of information per system clock cycle.
33291
Data bits of information are simultaneously transmitted by
one pin, Master Out Serial In (MOSI), and received by
another pin, Master In Serial Out (MISO), of the MCU.
8 Outputs
SI
SCLK
Some features of SPI are as follows:
CS
• Full duplex, three-wire synchronous data transfer
• Each microcontroller can be a master or a slave
• Provides write collision flag protection
• Provides end of message interrupt flag
• Four I/Os associated with SPI (MOSI, MISO, SCLK, SS)
Figure 14. Parallel Input SPI Control
Figure 15, page 13, illustrates a basic method of
controlling multiple 33291L devices using two MCUs. A
system can have only one master MCU at any given instant
of time and one or more slave MCUs. Master control of the
system must pass from one MCU to the other in an orderly
manner. The master MCU supplies the system clock signal
(top MCU designated the master); the lower MCU being the
slave. It is possible to have a system with more than one
Drawbacks to SPI are as follows:
• An MCU is required for efficient operational control
• In contrast to parallel input control it is slower at performing
pulse width modulating (PWM) functions.
33291L
Analog Integrated Circuit Device Data
Freescale Semiconductor
12
FUNCTIONAL DESCRIPTION
FUNCTIONAL PIN DESCRIPTION
MC68XX
Microcontroller
SPI
(Master)
33291
CS
SCLK
B0
B1
A0
A1
A2
Parallel
Ports
8 Outputs
8 Outputs
8 Outputs
8-Bit
SO
SI
SCLK
MISO
MOSI
8-Bit
V
DD
33291
SS
CS
SCLK
8-Bit
SO
MC68XX
Microcontroller
SPI
SI
(Alternate Master)
Parallel
Ports
B0
B1
A0
A1
A2
33291
CS
SCLK
MISO
MOSI
SCLK
8-Bit
SO
8-Bit
V
SI
DD
SS
Figure 15. Multiple MCU SPI Control
FUNCTIONAL PIN DESCRIPTION
absolutely necessary, the SCLK pin be kept in a low logic
state as long as the device is not accessed (CS in logic high
state). When CS is in a logic high state, signals at the SCLK
and SI pins are ignored and SO is tri-stated (high
impedance). See the Data Transfer Timing diagram in
Figure 17, page 16.
CHIP SELECT (CS)
The 33291L receives its MCU communication through the
CS pin. Whenever this pin is in a logic low state, data can be
transferred from the MCU to the 33291L by way of the SI pin
and from the 33291L to the MCU through the SO pin.
Clocked-in data from the MCU is transferred from the 33291L
Shift register and latched into the power outputs on the rising
edge of the CS signal. On the falling edge of the CS signal,
drain status information is transferred from the power outputs
then loaded into the Shift register of the device. The CS pin
also controls the output driver of the serial output (SO) pin.
Whenever the CS pin goes to a logic low state, the SO pin
output driver is enabled allowing information to be transferred
from the 33291L to the MCU. To avoid data corruption or the
generation of spurious data, it is essential the high-to-low
transition of the CS signal occur only when SCLK is in a logic
low state.
SERIAL INSTRUCTION (SI)
This pin is for the input of serial instruction (SI) data. SI is
read on the falling edge of SCLK. A logic high state present
on this pin when the SCLK signal rises will program a specific
output OFF. In turn, CS pin turns OFF the specific output on
the rising edge of the CS signal. Conversely, a logic low state
present on the SI pin will program the output ON, In turn, the
pin turns ON the specific output on the rising edge of the CS
signal.
To program the eight outputs of the 33291L ON or OFF, an
8-bit serial stream of data is required to be synchronously
entered into the SI pin starting with Output 7, followed by
Output 6, Output 5, and so on, to Output 0. Referring to
Figure 17, the DO bit is the most significant bit (MSB)
corresponding to Output 7. For each rise of the SCLK signal,
with CS held in a logic low state, a data-bit instruction (ON or
OFF) is synchronously loaded into the Shift register per the
data-bit SI state. The Shift register is full after eight bits of
information have been entered. To preserve data integrity,
care should be taken to not transition SI as SCLK transitions
from a low-to-high logic state.
SYSTEM CLOCK (SCLK)
The system clock (SCLK) pin clocks the internal shift
registers of the 33291L. The serial input (SI) pin accepts data
into the Input Shift register on the falling edge of the SCLK
signal while the serial output (SO) pin shifts data information
out of the SO line driver on the rising edge of the SCLK signal.
False clocking of the Shift register must be avoided to
guarantee validity of data. It is essential the SCLK pin be in a
logic low state whenever the chip select bar (CS) pin makes
any transition. For this reason, it is recommended, though not
33291L
Analog Integrated Circuit Device Data
Freescale Semiconductor
13
FUNCTIONAL DESCRIPTION
FUNCTIONAL PIN DESCRIPTION
A simple power ON reset delay of the system can be
programmed through the use of an RC network comprised of
a shunt capacitor from the RST pin to Ground and a resistor
to VDD, illustrated in Figure 16. Care should be exercised
ensuring proper discharge of the capacitor. Careful attention
eliminates adverse delay of the RST and damage of the MCU
if it pulls the Reset line low, thereby accomplishing
initialization for turn ON delay. It may be easier to incorporate
delay into the software program and use a parallel port pin of
the MCU to control the 33291L RST pin.
SERIAL OUTPUT (SO)
The serial output (SO) pin is the tri-stateable output from
the Shift register. The SO pin remains in a high impedance
state until the CS pin goes to a logic low state. The SO data
reports the drain status, either high or low relative to the
previous command word. The SO pin changes state on the
rising edge of SCLK and reads out on the falling edge of
SCLK. When an output is OFF and not faulted, the
corresponding SO data-bit is a high state. When an output is
ON, and there is no fault, the corresponding data-bit on the
SO pin will be a low logic state. The SI/SO shifting of data
follows a first-in-first-out (FIFO) protocol with both input and
output words transferring the MSB first. Referring to
Figure 17, the DO bit is the MSB corresponding to Output 7
relative to the previous command word. The SO pin is not
affected by the status of the RST pin.
VDD
+
RDLY
20 μA
Reset
MCU
Reset
RESET (RST)
C
DLY
The 33291L Reset (RST) pin is active low. It is used to
clear the SPI Shift register. In doing so, all output switches
are set at OFF. With the device in a system with an MCU,
upon initial system power-up, the MCU holds the RST pin of
the device in a logic low state, ensuring all outputs to be OFF
until both the VDD and VPWR pin voltages are adequate for
predictable operation. After the 33291L is reset, the MCU is
ready to assert system control with all output switches initially
OFF.
33291
Figure 16. Power ON Reset
SHORT FAULT PROTECT DISABLE (SFPD)
The Short Fault Protect Disable (SFPD) pin is used to
prevent the outputs from latching-off due to an overcurrent
condition. This feature provides control of incandescent lamp
loads where in-rush currents exceed the device’s analog
current limits. Essentially the SFPD pin determines whether
the 33291L output(s) will instantly shut down upon sensing an
output short or remain ON in a current limiting mode of
operation until the output short is removed or thermal
shutdown is reached. If the SFPD pin is tied to VDD = 5.0 V
the 33291L output(s) will remain ON in a current limited mode
of operation upon encountering a load short to supply or
overcurrent condition. When the SFPD pin is grounded, a
short circuit will immediately shut down only the output
affected. Other outputs not having a fault condition will
operate normally. The short circuit operation is addressed in
more detail later.
If the VPWR pin of the 33291L experiences a low voltage,
following normal operation, the MCU should pull the RST pin
low to shut down the outputs and clear the input data register.
The RST pin is active low and has an internal pull-down
incorporated to ensure operational predictability should the
external pull-down of the MCU open circuit. The internal pull-
down is only 25 μA, affording safe and easy interfacing to the
MCU. The RST pin of the 33291L should be pulled to a logic
low state for a duration of at least 250 ns to ensure reliable a
reset.
33291L
Analog Integrated Circuit Device Data
Freescale Semiconductor
14
FUNCTIONAL DESCRIPTION
application requires lower power dissipation or the added
capability of switching higher currents.
POWER CONSUMPTION
The 33291L has extremely low power consumption in both
the operating and standby modes. In the standby, or Sleep,
mode, with VDD ≤ 2.0 V, the current consumed by the VPWR
pin is less than 25 μA. In the operating mode, the current
drawn by the VDD pin is less than 4.0 mA (1.0 mA typical)
while the current drawn at the VPWR pin is 2.0 mA maximum
(1.0 mA typical). During normal operation, turning outputs
ON increases IPWR by only 20 μA per output. Each output
experiencing a soft short (overcurrent conditions just under
the current limit) adds 0.5 mA to the IPWR current
Performance of parallel operation results in a
corresponding decrease in RDS(ON) while the Output OFF
Open Load Detect Currents and the Output Current Limits
increase correspondingly (by a factor of eight if all outputs are
paralleled). Less than 125 mΩ RDS(ON) at 25°C with current
limiting of 8 A to 24 A will result if all outputs are paralleled
together. There will be no change in the overvoltage detect or
the OFF output threshold voltage range. The advantage of
paralleling outputs within the same 33291L affords the
existence of minimal RDS(ON) and output clamp voltage
variation between outputs.
PARALLELING OF OUTPUTS
Typically, the variation of RDS(ON) between outputs of the
same device is less than 0.5 percent. The variation in clamp
voltages, potentially affecting dynamic current sharing, is less
than five percent. Paralleling outputs from two or more
different devices is possible, but it is not recommended.
There is no guarantee the RDS(ON) and clamp voltage of the
two devices will match. System level thermal design analysis
and verification should be conducted whenever paralleling
outputs, particularly where different devices are involved.
Using MOSFETs as output switches permits connecting
any combination of outputs together. RDS(ON) of MOSFETs
have an inherent positive temperature coefficient providing
balanced current sharing between outputs without
destructive operation (bipolar outputs could not be paralleled
in this fashion as thermal run-away would likely occur). The
device can even be operated with all outputs tied together.
This mode of operation may be desirable in the event the
33291L
Analog Integrated Circuit Device Data
Freescale Semiconductor
15
FUNCTIONAL DESCRIPTION
Figure 17. Data Transfer Timing
33291L
Analog Integrated Circuit Device Data
Freescale Semiconductor
16
FUNCTIONAL DESCRIPTION
With the exception of the Overvoltage Fault, all of these
faults are output specific. Overtemperature Detect, Output
OFF Open Detect, and Output Short Detect are dedicated to
each output separately such that the outputs are independent
in operation. A VPWR Overvoltage Detect is of a global nature,
causing all outputs to be turned OFF.
FAULT LOGIC OPERATION
INTRODUCTION
The MCU can perform a parity check of the fault logic
operation by comparing the command 8-bit word to the status
8-bit word. Assume after system reset, the MCU first sends
an 8-bit command word to the 33291L. This word is called
Command Word 1. Each output to be turned ON will have its
corresponding data bit low. Refer to the data transfer timing
illustration in Figure 17.
OVERTEMPERATURE FAULT
Patent pending Overtemperature Detect and shutdown
circuits are specifically incorporated for each individual
output. The shutdown following an Overtemperature
condition is independent of the system clock or any other
logic signal. Each independent output shuts down at 155°C
to 185°C. When an output shuts down due to an
Overtemperature Fault, no other outputs are affected. The
MCU recognizes the fault since the output was commanded
to be ON and the status word indicates it is OFF. A maximum
hysteresis of 20°C ensures an adequate time delay between
output turn OFF and recovery. This avoids a very rapid turn
ON and turn OFF of the device around the Overtemperature
threshold. When the temperature falls below the recovery
level for the Overtemperature Fault, the device will turn ON
only if the Command Word during the next write cycle
indicates the output should be turned ON.
As Command Word 1 is being written into the Shift register
of the 33291L, a status word is being simultaneously written
and received by the MCU. However, the word being received
by the MCU is the status of the previous write word to the
33291L, Status Word 0. If the command word of the MCU is
written a second time (Command Word 2 = Command Word
1), the word received by the MCU, Status Word 2, is the
status of Command Word 1. The timing diagram illustrated in
Figure 17 depicts this operation. Status Word 2 is then
compared with Command Word 1. The MCU will Exclusive
OR Status Word 2 with Command Word 1 to determine if the
two words are identical. If the two words are identical, no
faults exist. The timing between the two write words must be
greater than 100 μs to receive proper drain status. The
system data bus integrity may be tested by writing two like
words to the 33291L within a few microseconds of each
other.
OVERVOLTAGE FAULT
An Overvoltage condition on the VPWR pin causes the
33291L to shut down all outputs until the overvoltage
condition is removed and the device is re-programmed by the
SPI. The overvoltage threshold on the VPWR pin is specified
as 28 V to 36 V with 1.0 V typical hysteresis. Following the
overvoltage condition, the next write cycle sends the SO pin
the hexadecimal word $FF (all ones), indicating all outputs
are turned OFF. In this way, potentially dangerous timing
problems are avoided and the MCU reset routine ensures an
orderly startup of the loads. The 33291L does not detect an
overvoltage on the VDD pin. Other external circuitry, such as
the Motorola 33161 Universal Voltage Monitor, is necessary
to accomplish this function.
INITIAL SYSTEM SETUP TIMING
The MCU can monitor two kinds of faults:
1. Communication errors on the data bus
2. Actual faults of the output loads
After initial system startup or reset, the MCU will write one
word to the 33291L. If the word is repeated within
approximately five microseconds of the first word, the word
received by the MCU, at the end of the repeated word, serves
as a confirmation of data bus integrity (1). At startup, the
33291L will take 25 μs to 100 μs before a repeat of the first
word should be repeated at least 100 μs later to verify the
status of the outputs.
OUTPUT OFF OPEN LOAD FAULT
The SO of the 33291L will indicate any one of four faults.
The four possible faults are:
An Output OFF Open Load Fault is the detection and
reporting of an open load when the corresponding output is
disabled (input bit programmed to a logic high state). To
understand the operation of the Open Load Fault detect
circuit, see Figure 18. The Output OFF Open Load Fault is
detected by comparing the drain voltage of the specific
MOSFET output to an internally generated reference. Each
output has one dedicated comparator for this purpose.
1. Overtemperature
2. Output OFF Open Fault
3. Short Fault (overcurrent)
4. VPWR Overvoltage Fault
33291L
Analog Integrated Circuit Device Data
Freescale Semiconductor
17
FUNCTIONAL DESCRIPTION
SHORTED LOAD FAULT
A short load, or overcurrent fault can be caused by any
output being shorted directly to supply, or an output
experiencing a current greater than the current limit.
33291
V
PWR
Low = Fault
There are three safety circuits progressively in operation
during load short conditions providing system protection.
They are as follows:
R
L
MOSFET OFF
+
–
Output
1. The output current of the device is monitored in an
analog fashion using a SENSEFET approach and
current limited.
μ
50
A
2. The output current of the device is sensed by
monitoring the MOSFET drain voltage.
V
Thres
2.5 V to 3.5 V
3. The output thermal limit of the device is sensed and
when attained causes only the specific faulted output
to be latched OFF, allowing all remaining outputs to
operate normally.
Figure 18. Output OFF Open Load Fault
An Output OFF Open Load Fault is indicates when the
output voltage is less than the Output Threshold Voltage
(VThres) of 0.6 to 0.8 x VDD. Since the 33291L outputs function
as switches, during normal operation, each MOSFET output
should either be completely turned ON or OFF. By design,
the threshold voltage was selected to be between the ON and
OFF voltage of the MOSFET. During normal operation, the
ON state VDS voltage of the MOSFET is less than the
threshold voltage and the OFF state VDS voltage is greater
than the threshold voltage. This design approach affords
using the same threshold comparator for Output Open Load
Detect in the OFF state and Short Circuit Detect in the ON
state. (See Figure 19 for an understanding of the Short
Circuit Detect circuit.) With VDD = 5.0 V, an OFF state output
voltage of less than 3.0 V will be detected as an Output OFF
Open Load Fault while voltages greater than 4.0 V will not be
detected as a fault.
All three protection mechanisms are incorporated in their
output, affording robust independent output operation.
The analog current limit circuit is always active and
monitors the output drain current. An overcurrent condition
causes the gate control circuitry to reduce the gate-to-source
voltage imposed on the output MOSFET, re-establishing the
load current in compliance with current limit (1.0 A to 3.0 A)
range. The time required for the current limit circuitry to act is
less than 20 μs. Therefore, currents higher than 1.0 A to
3.0 A will never be seen for more than 20 μs (a typical
duration is 10 μs). If the current of an output attempts to
exceed the predetermined limit of 1.0 A to 3.0 A (2.0 A
nominal), the VDS voltage will exceed the VThres voltage and
the overcurrent comparator will be tripped as shown in
Figure 19.
The 33291L has an internal pull-down current source of
50 μA, illustrated in Figure 18, page 18, between the
33291
MOSFET drain and ground. This current source prevents the
output from floating up to VPWR if there is an open load or
internal wire bond failure. The internal comparator compares
the drain voltage with a reference voltage, VThres (0.6 to 0.8 x
VDD). If the output voltage is less than this reference voltage,
the 33291L will declare the condition to be an open load fault.
V
PWR
High = Fault
R
L
MOSFET ON
+
–
Output
Digital
V
During output switching, especially with capacitive loads,
a false output OFF Open Load Fault may be triggered. To
prevent this false fault from being reported, an internal fault
filter in the range of 25 μs to 100 μs is incorporated. The
duration in which a false fault may be reported is a function of
the load impedance (RL,CL,LL), RDS(ON), and COUT of the
MOSFET as well as the supply voltage (VPWR). The rising
edge of CS triggers a built-in fault delay timer which must
time out (25 μs or 100 μs) before the fault comparator is
enabled to detect at faulted threshold. The circuit
–
+
Analog
ref
V
Thres
2.5 to 3.5 V
Figure 19. Short Circuit Detect and
Analog Current Limiting Circuit
automatically returns to normal operation once the condition
causing the Open Load Fault is removed.
The status of SFPD determines whether the 33291L will
shut down immediately or continue to operate in an analog
current limited mode until either the short circuit (overcurrent)
condition is removed or thermal shutdown is reached.
33291L
Analog Integrated Circuit Device Data
Freescale Semiconductor
18
FUNCTIONAL DESCRIPTION
Grounding the SFPD pin will enable the short fault
protection shutdown circuitry. Consider a load short (output
short to supply) occurring on an output before, during, and
after output turn ON. When the CS signal rises to the high
logic state, the corresponding output is turned ON and a
delay timer is activated. The duration of the delay timer is
70 μs to 250 μs. If the short circuit takes place before the
output is turned ON, the delay experienced is the entire 70 μs
to 250 μs followed by shutdown. If the short occurs during the
delay time, the shutdown still occurs after the delay time has
elapsed. However, if the short circuit occurs after the delay
time, shutdown is immediate (within 20 μs after sensing). The
purpose of the delay timer is to prevent false faults from being
reported when switching capacitive loads.
the SFPD pin should be. Usually if at least one load is, say an
incandescent lamp, the in-rush current on that input will be
milliseconds in duration. Therefore, setting SFPD at 5.0 V will
prevent shutdown of the output due to the in-rush current.
The system relies only on the overtemperature shutdown to
protect the outputs and the loads. The 33291L was designed
to switch GE194 incandescent lamps (or equivalents) with
the SFPD pin in a grounded state. Considerably larger lamps
can be switched with the SFPD pin held in a high logic state.
Sometimes both a delay period greater than 70 μs to
250 μs (current limiting of the output) followed by an
immediate overcurrent shutdown is necessary. This can be
accomplished by programming the SFPD pin to 5.0 V for the
extended delay period, allowing the outputs to remain ON in
a current limited mode, then grounding it to accomplish the
immediate shutdown after a period of time. Additional
external circuitry is required to implement this type of
function. An MCU parallel output port can be devoted to
controlling the SFPD voltage during and after the delay
period; this is often a much better method. In either case,
care should be taken to execute the SFPD start-up routine
every time startup or reset occurs.
If the SFPD pin is at 5.0 V (or VDD), an output will not be
disabled when an overcurrent is detected. The specific output
will, within 5.0 μs to 10 μs of encountering the short circuit, go
into an analog current limited mode. This feature is especially
useful when switching incandescent lamp loads, where high
in-rush currents experienced during startup last for 10 ms to
20 ms.
Each output of the 33291L has its own overcurrent
shutdown circuitry. Overtemperature faults and overvoltage
faults are not affected by the SFPD pin’s state.
UNDERVOLTAGE SHUTDOWN
An undervoltage VDD condition will result in the global
shutdown of all outputs. The undervoltage threshold is
between 2.5 V and 3.5 V. When VDD goes below the
threshold, all outputs are turned OFF and the Serial Output
data register is reset to indicate the same.
Both load current sensing and output voltage sensing are
incorporated for Short Fault detection with actual detection
occurring slightly after the onset of current limit. The current
limit circuitry incorporates a SENSEFET approach to
measure the total drain current. This calls for the current
through a small number of cells in the power MOSFET to be
measured and the result multiplied by a constant, giving the
total current. Whereas an output shutdown circuitry
An undervoltage condition at the VPWR pin will not cause
output shutdown and reset. When VPWR is between 5.5 V
and 9.0 V, the outputs will operate per the command word.
However, the status as reported by the SO pin may not be
accurate below 9.0 V VPWR. Proper operation at VPWR
voltages below 5.5 V are not be guaranteed.
measures the drain-to-source voltage, shutting down the
output if its threshold (VTHRES) will be exceeded.
Short fault detection is accomplished by sensing the
output voltage and comparing it to VThres. The lowest VThres
requires a voltage of 2.5 V to be sensed. For an enabled
output, with VDD = 5.0 0.5 V, an output voltage in excess of
3.5 V will be detected as a short (overcurrent condition), while
voltages less than 2.5 V will not be detected as shorts.
DECIPHERING FAULT TYPE
The 33291L SO pin can be used to determine what kind of
system fault has occurred. With eight outputs having open
load, overcurrent, overtemperature, and overvoltage faults, a
total of 25 different faults are possible. The SO status word
received by the MCU will be compared with the word sent to
the 33291L during the previous write cycle. For a specific
output, if the SO bit compares with the corresponding SI bit
of the previous word, the output is operating normal with no
fault. Only when the SO bit and previous word SI bit differ is
there a fault indicated. If the two words are not the same, the
MCU should be programmed to determine which output or
outputs are faulted.
OVERCURRENT RECOVERY
If the SFPD pin is in a high logic state, the circuit returns to
normal operation automatically after the short circuit is
removed (unless thermal shutdown has occurred).
If the SFPD pin is grounded and overcurrent shutdown
occurs, removing the short circuit will result in the output
remaining OFF until the next write cycle. If the short circuit is
not removed, the output will turn ON for the delay time (70 μs
to 250 μs) and then turn OFF for every write cycle
commanding a turn ON.
If for a specific output the initial SI command bit were logic
high, the output would be programmed to be off; if upon the
next command word being entered, a logic low came back on
SO, for that specific output’s corresponding bit an output-off
open-load fault would be indicated. The resulting SO bit for
that specific output would be different from that entered
during the previous word for that SI bit, indicating the fault.
SFPD PIN VOLTAGE SELECTION
Since the voltage condition of the SFPD pin controls the
activation of the short fault protection (i.e., shutdown) mode
equally for all eight outputs, the load having the longest
duration of in-rush current determines what voltage (state)
33291L
Analog Integrated Circuit Device Data
Freescale Semiconductor
19
FUNCTIONAL DESCRIPTION
The eight output-off open-load faults are therefore most
easily detected.
Drain-to-Source Clamp
Voltage (VCL = 65 V)
If for a specific output the initial SI command bit were a
logic low, when calling for the output to be programmed on,
the next word command entered into the corresponding bit
returns with a logic high on SO. An output overcurrent fault
would be indicated. An overcurrent fault is always reported by
the SO output and is independent of the logic state existing
on the SFPD pin. When the SFPD pin is in a logic high state,
an overcurrent condition will be reported on the SO pin.
However, limiting output current is in effect and the output is
permitted to operate if the overcurrent condition does not
drive output into an overtemperature fault. An
Drain Voltage
Clamp Energy
Drain Current
(ID = 0.5 A)
(E = I x V x t)
J
A
CL
VPWR
Drain-to-Source ON
Voltage (V
)
Current
DS(ON)
Area (I )
overtemperature fault will shut down the specific output
effected for the duration of the overtemperature condition.
A
Time
GND
Overcurrent and overtemperature faults are often related.
Turning the effected output switches OFF and waiting for
some time to allow the output to cool down should make
these types of faults go away. Soft overcurrent faults can
sometimes be determined over hard short faults and
overtemperature faults by observing the time required for the
device to recover. However, in general overcurrent and
overtemperature faults cannot be differentiated in normal
application usage.
Figure 20. Output Voltage Clamping
THERMAL CHARACTERIZATION
THERMAL MODEL
Logic functions take up a very small area of the die and
generate negligible power. In contrast, the output transistors
take up most of the die area and are the primary contributors
of power generation. The thermal model illustrated in
Figure 21, page 21, was developed for the 33291L mounted
on a typical PC board. The model is accurate for both steady
state and transient thermal conditions. The components Rd0
through Rd7 represent the steady state thermal resistance of
the silicon die for transistor outputs 0 through 7, while Cd0
through Cd7 represent the corresponding thermal
An advantage of the synchronous serial output is multiple
faults can be detected with only one (SO) pin being used for
fault status reporting.
If VPWR experiences an overvoltage condition, all outputs
will immediately be turned OFF and remain latched OFF. A
new command word is required to turn the outputs back ON
following an overvoltage condition.
capacitance of the silicone die translator outputs and plastic.
The device area and die thickness determine the values of
these specific components.
Output Voltage Clamping
Each output of the 33291L incorporates an internal voltage
clamp to provide fast turn-off and transient protection of the
output. Each clamp independently limits the drain-to-source
voltage to 53 V at drain currents of 0.5 A and keeps the
output transistors from avalanching by causing the transient
energy to be dissipated in the linear mode (see Figure 20).
The total energy clamped (EJ) can be calculated by
multiplying the current area under the current curve (IA) times
the clamp voltage (VCL) times the duration the clamp is active
(t).
The thermal impedance of the package from the internal
mounting flag to the outside environment is represented by
the terms Rpkg and Cpkg. The steady state thermal resistance
of leads and the PC board make up the steady state package
thermal resistance, Rpkg. The thermal capacitance of the
package is made up of the combined capacitance of the flag
and the PC board. The mode compound was not modeled as
a specific component but it is factored into the other overall
component values.
The battery voltage in the thermal model represents the
ambient temperature the device and PC board are subjected
to. The IPWR current source represents the total power
dissipation and is calculated by totalling the power dissipation
of each individual output transistor. This is easily
accomplished by knowing RDS(ON) and load current of the
individual outputs.
Characterization of the output clamps, using a single pulse
non-repetitive method at 0.5 A, indicates the maximum
energy to be 50 mJ at 150°C junction temperature per output.
Very satisfactory steady state and transient results are
experienced with this thermal model. Tests indicate the
model accuracy to have less than 10 percent error. Output
interaction with an adjacent output is believed to be the main
contributor to the thermal inaccuracy. Tests indicate little or
no detectable thermal effects caused by distant output
transistors isolated by one or more other outputs. Tests were
33291L
Analog Integrated Circuit Device Data
Freescale Semiconductor
20
FUNCTIONAL DESCRIPTION
conducted with the device mounted on a typical PC board
placed horizontally in a 33 cubic inch still air enclosure. The
PC board was made of FR4 material measuring 2.5 by
2.5 inches, having double-sided circuit traces of 1.0 ounce
copper soldered to each device pin. The board temperature
was measured with thermal couple soldered to the board
surface one inch away from the center of the device. The
ambient temperature of the enclosure was measured with a
second thermal couple located over the center of one inch
distance from device.
The junction-to-ambient temperature resistance was found to
be 40°C/W with a single output active (34°C/W with all
outputs dissipating equal power 0 and the thermal resistance
from junction-to-PC board (Rjunction-board) to be 30°C/W
(board temperature, measure one inch from device center).
The junction-to-heatsink lead resistance was found again to
approximate 10°C/W. Devoting additional PC board metal
around the heatsinking pins for this package improved the
Rpkg from 33° to 31°C/W.
The total power dissipation available is dependent on the
number of outputs enabled at any one time. At 25°C the
RDS(ON) in 450 mΩ with a coefficient of 6500 ppm/°C. For the
junction temperature to remain below 150°C, the maximum
available power dissipation must decrease as the ambient
temperature increases. Figure 24 depicts the per output limit
of current at ambient temperatures necessary when one,
four, or eight outputs are enable ON. Figure 23 illustrates
how the RDS(ON) output value is affected by junction
temperature.
THERMAL PERFORMANCE
Figure 21 illustrates the worst case thermal component
parameters values for the 33291L in the 24-lead SOIC wide
body surface mount package. Pins 5, 6, 7, 8, 17, 18, 19, and
20 of the package were connected directly to the lead frame
flag. The parameter values indicated take into account
adjacent output combinations. The characterization was
conducted over power dissipation levels of 0.7 W to 17 W.
Junction Temperature Node
V
- T (C°)
D
D
(Volts represent Die Surface Temperature)
Output 0
Output 1
Output 2
Output 6
Output 7
C
C
C
C
C
d7
R
R
R
R
R
d7
d0
d1
d2
d6
d0
d1
d2
d6
Flag Temperature Node
I
(Steady State or Transient)
PWR
(1.0 A = 1.0 W of Device Power Dissipation)
R
= R
leads
+ R
C
= C
+ C
flag PC Board
pkg
PC Board
pkg
Ambient Temperature Node
= T (C°)
C
(F)*
R
(Ω)*
C
pkg
(F)*
Rdx
(Ω)*
dx
pkg
V
Package
A
A
(1.0 V = 1°C Ambient Temperature)
24-Lead
SOIC
7.0
0.002
33
0.15
* Ω = °C/W, F = W s/°C, I
= W, and V = °C
A
PWR
Figure 21. Thermal Model (Electrical Equivalent)
33291L
Analog Integrated Circuit Device Data
Freescale Semiconductor
21
FUNCTIONAL DESCRIPTION
3.0
2.5
2.0
1 Output ON (40°C/W)
R
1 Output ON (37°C/W)
RDS(on)@150°C=0.8:
@ 150°C=0.8Ω
T =150°C
J
DS(ON)
2.5
2.0
TJ =150°C
4 Outputs ON (35°C/W)
1.5
1.0
4 Outputs ON (32°C/W)
1.5
1.0
8 Outputs ON (34°C/W)
8 Outputs ON (31°C/W)
0.5
0
0.5
0
-50 -25
0
25
50 75 100 125 150
-50 -25
0
25
50 75 100 125 150
TA Ambient Temperature (C°)
TA, Ambient Temperature (C°)
Figure 23. Maximum SOP Package Steady State Output
Current vs. Ambient Temperature
Figure 22. Maximum DIP Package Steady State Output
Current vs. Ambient Temperature
1.6
VPWR = 13 V
1.5
1.4
1.3
1.2
1.1
1.0
0.9
V
DD = 5.0 V
I
OUT = 0.5 A
-50 -25
0
25
50 75 100 125 150
TJ Junction Temperature (°C)
Figure 24. Maximum Output ON Resistance vs. Junction
Temperature
33291L
Analog Integrated Circuit Device Data
Freescale Semiconductor
22
PACKAGING
PACKAGE DIMENSIONS
PACKAGING
PACKAGE DIMENSIONS
For the most current package revision, visit www.freescale.com and perform a keyword search using the “98A” listed below.
DW SUFFIX
EG SUFFIX (PB-FREE)
20-PIN
98ASB42344B
ISSUE G
For the most current package revision, visit www.freescale.com and perform a keyword search using the “98A” listed below.
33291L
Analog Integrated Circuit Device Data
Freescale Semiconductor
23
PACKAGING
PACKAGE DIMENSIONS
DW SUFFIX
EG SUFFIX (PB-FREE)
20-PIN
98ASB42344B
ISSUE G
33291L
Analog Integrated Circuit Device Data
Freescale Semiconductor
24
REVISION HISTORY
PACKAGE DIMENSIONS
REVISION HISTORY
REVISION
DATE
DESCRIPTION OF CHANGES
• Implemented Revision History page
• Converted to Freescale format
8/2006
3.0
• Added EPP prefix Z to EG suffix device
• Removed MC33291LEG/R2 and replaced with MCZ33291LEG/R2 in the Ordering
Information block
• Removed Peak Package Reflow Temperature During Reflow (solder reflow) parameter
from Maximum ratings on page page 5. Added note with instructions to obtain this
information from www.freescale.com.
7/2008
9/2008
4.0
5.0
• Corrected RDS(ON) in Static Electrical Table to reflect an earlier version of the
document which inadvertantly was changed.
33291L
Analog Integrated Circuit Device Data
Freescale Semiconductor
25
How to Reach Us:
Home Page:
www.freescale.com
RoHS-compliant and/or Pb-free versions of Freescale products have the functionality
and electrical characteristics of their non-RoHS-compliant and/or non-Pb-free
counterparts. For further information, see http://www.freescale.com or contact your
Freescale sales representative.
Web Support:
http://www.freescale.com/support
USA/Europe or Locations Not Listed:
Freescale Semiconductor, Inc.
Technical Information Center, EL516
2100 East Elliot Road
For information on Freescale’s Environmental Products program, go to http://
www.freescale.com/epp.
Tempe, Arizona 85284
+1-800-521-6274 or +1-480-768-2130
www.freescale.com/support
Europe, Middle East, and Africa:
Freescale Halbleiter Deutschland GmbH
Technical Information Center
Schatzbogen 7
81829 Muenchen, Germany
+44 1296 380 456 (English)
+46 8 52200080 (English)
+49 89 92103 559 (German)
+33 1 69 35 48 48 (French)
www.freescale.com/support
Information in this document is provided solely to enable system and software
implementers to use Freescale Semiconductor products. There are no express or
implied copyright licenses granted hereunder to design or fabricate any integrated
circuits or integrated circuits based on the information in this document.
Freescale Semiconductor reserves the right to make changes without further notice to
any products herein. Freescale Semiconductor makes no warranty, representation or
guarantee regarding the suitability of its products for any particular purpose, nor does
Freescale Semiconductor assume any liability arising out of the application or use of any
product or circuit, and specifically disclaims any and all liability, including without
limitation consequential or incidental damages. “Typical” parameters that may be
provided in Freescale Semiconductor data sheets and/or specifications can and do vary
in different applications and actual performance may vary over time. All operating
parameters, including “Typicals”, must be validated for each customer application by
customer’s technical experts. Freescale Semiconductor does not convey any license
under its patent rights nor the rights of others. Freescale Semiconductor products are
not designed, intended, or authorized for use as components in systems intended for
surgical implant into the body, or other applications intended to support or sustain life,
or for any other application in which the failure of the Freescale Semiconductor product
could create a situation where personal injury or death may occur. Should Buyer
purchase or use Freescale Semiconductor products for any such unintended or
unauthorized application, Buyer shall indemnify and hold Freescale Semiconductor and
its officers, employees, subsidiaries, affiliates, and distributors harmless against all
claims, costs, damages, and expenses, and reasonable attorney fees arising out of,
directly or indirectly, any claim of personal injury or death associated with such
unintended or unauthorized use, even if such claim alleges that Freescale
Japan:
Freescale Semiconductor Japan Ltd.
Headquarters
ARCO Tower 15F
1-8-1, Shimo-Meguro, Meguro-ku,
Tokyo 153-0064
Japan
0120 191014 or +81 3 5437 9125
support.japan@freescale.com
Asia/Pacific:
Freescale Semiconductor Hong Kong Ltd.
Technical Information Center
2 Dai King Street
Tai Po Industrial Estate
Tai Po, N.T., Hong Kong
+800 2666 8080
support.asia@freescale.com
For Literature Requests Only:
Freescale Semiconductor Literature Distribution Center
P.O. Box 5405
Semiconductor was negligent regarding the design or manufacture of the part.
Denver, Colorado 80217
Freescale™ and the Freescale logo are trademarks of Freescale Semiconductor, Inc.
All other product or service names are the property of their respective owners.
1-800-441-2447 or 303-675-2140
Fax: 303-675-2150
© Freescale Semiconductor, Inc., 2007 - 2008. All rights reserved.
LDCForFreescaleSemiconductor@hibbertgroup.com
MC33291L
Rev. 5.0
9/2008
相关型号：
©2020 ICPDF网 联系我们和版权申明