FAN156 [FAIRCHILD]
Low Voltage Comparator; 低电压比较器型号: | FAN156 |
厂家: | FAIRCHILD SEMICONDUCTOR |
描述: | Low Voltage Comparator |
文件: | 总9页 (文件大小:733K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
May 2011
FAN156
Low Voltage Comparator
Features
Description
The FAN156 is a low-power single comparator that
typically consumes less than 10µA of supply current. It
is guaranteed to operate at a low voltage of 1.6V and is
fully operational up to 5.5V, making it convenient for use
in 1.8, 3.0V, and 5.0V systems.
.
.
.
.
.
.
.
Low Supply Current: IDD 6μA (Typical)
Single Power Supply Operation
Wide Common-Mode Input Voltage Range
Push-Pull Output Circuit
The FAN156 has a complementary push-pull P- and N-
channel output stage capable of driving a rail-to-rail
output swing with a load ranging up to 5.0mA.
Low Input Bias Current
Internal Hysteresis
Packaged in MicroPak™ 6
Applications
.
.
.
Mobile Phones
Alarm and Security Systems
Personal Digital Assistants
Figure 1. Fuonal Diagram
Ordering Information
Top
Part Number
Mark
Operating Temperature
Range
Package
Packing Method
5000 Units on
Tape and Reel
FAN156L6X
CN
-40 to 85°C
6-Lead, MicroPak™, 1x1mm Wide
© 2010 Fairchild Semiconductor Corporation
FAN156 • Rev. 1.0.0
www.fairchildsemi.com
Pin Configuration
1
2
3
6
5
4
OUT
VSS
IN+
V
DD
NC
IN-
Figure 2. Pin Configuration (Top-Through View)
Pin Definitions
Pin #
Name
OUT
VSS
Description
1
2
3
4
5
6
Comparator Output
Negative Supply Voltage
Non-Inverting Input
Inverting Input
IN+
IN-
NC
No Connect
VDD
Positive Supply Voltage
Function Table
Inputs
Outputs
IN(-) > IN(+)
IN(+) > IN(-)
Output LOW
Output HIGH
VDD
VDD
VOUT
VOUT
VIN(-)
VOUT
VOUT
VIN (+)
VIN (-)
VIN(+)
Figure 3. VIN vs. VOUT
© 2010 Fairchild Semiconductor Corporation
FAN156 • Rev. 1.0.0
www.fairchildsemi.com
2
Absolute Maximum Ratings
Stresses exceeding the absolute maximum ratings may damage the device. The device may not function or be
operable above the recommended operating conditions and stressing the parts to these levels is not recommended.
In addition, extended exposure to stresses above the recommended operating conditions may affect device reliability.
The absolute maximum ratings are stress ratings only.
Symbol
Parameter
Condition
Min.
-3.0
0
Max.
+3.0
6.0
Unit
VDD to VSS Supply Voltage
V
DVIN
VIN
ts
Differential Input Voltage
±6
Input Voltage
VSS to VDD
Indefinite
+150
+150
194
V
s
Output Short Circuit Duration(1)
Junction Temperature
Storage Temperature Range
Power Dissipation
TJ
°C
TSTG
PD
-65
°C
mW
°C/W
Thermal Resistance
335
JA
Air Gap
15
IEC 61000-4-2 System ESD
Contact
All Pins
8
8
JEDEC JESD22-A114, Human Body
Model
ESD
kV
Pin to Pin: IN(-), IN(+)
to VDD or VSS
12
2
JEDEC JESD22-C101, Charged
Device Model
All Pins
Note:
1. The maximum total power dissipation must not be exceeded.
Recommended Operating Conditions
The Recommended Operating Conditions table defines the conditions for actual device operation. Recommended
operating conditions are specified to ensure optimal performance to the datasheet specifications. Fairchild does not
recommend exceeding them or designing to Absolute Maximum Ratings.
Symbol
Parameter
Condition
Min.
-2.75
0
Max.
Unit
+2.75
VDD to VSS Power Supply
V
5.50
VDD
VIN
Power Supply
Input Voltage
VSS 0V
1.6
5.5
V
V
VSS to VDD
VDD 5.0V
VDD 3.0V
VDD 1.6V
5
3
IOH/IOL
Output Sink/Source Current
mA
°C
1
TA
Operating Temperature, Free Air
-40
+85
© 2010 Fairchild Semiconductor Corporation
FAN156 • Rev. 1.0.0
www.fairchildsemi.com
3
Electrical Characteristics
Symbol
Parameter
Condition
Min.
Typ.
Max.
Unit
VDD=5.5V, VSS=GND, and TA=+25°C
VHYS
VIO
Input Hysteresis
Input Offset Voltage(2)
VCM=0.5VDD
VCM=0.5VDD
4
mV
mV
pA
pA
V
-15
VSS
45
±1
10
10
+15
IIO
Input Offset Current
II
Input Bias Current
VCM
CMRR
IDD
Common Mode Input Voltage
Common Mode Rejection Ratio(3)
Supply Current
VDD
17
VCM=VDD
68
6
dB
µA
dB
PSRR
Power Supply Rejection Ratio(3)
ΔVDD=0.5V
VO=VDD
80
60
90
0.1
5.4
IOS
Output Short Circuit Current
mA
VO=VSS
VOL
VOH
Low-Level Output Voltage
High-Level Output Voltage
ISINK=5.0mA
ISOURCE=5.0mA
0.3
V
V
5.2
Overdrive 20mV,
CL=15pF
tPLH
tPHL
Propagation Delay (Turn-On)
Propagation Delay (Turn-Off)
0.40
0.42
µs
µs
Overdrive=20mV,
CL=15pF
tTLH
tTHL
VDD=3V, VSS=GND, and TA=+25°C
4.0
5.4
Response Time, Output Rise/Fall(4) CL=50pF
ns
VHYS
VIO
Input Hysteresis
Input Offset Voltage(2)
VCM=0.5VDD
VCM=0.5VDD
4
mV
mV
pA
pA
V
-15
VSS
45
±1
10
10
+15
IIO
Input Offset Current
II
Input Bias Current
VCM
CMRR
IDD
Common Mode Input Voltage
Common Mode Rejection Ratio(3)
Supply Current
VDD
VCM=VDD
60
5.5
80
dB
µA
dB
15.0
PSRR
Power Supply Rejection Ratio(3)
ΔVDD=0.5V
VO=VDD
27
IOS
Output Short Circuit Current
mA
VO=VSS
35
VOL
VOH
Low-Level Output Voltage
High-Level Output Voltage
ISINK=3.0mA
ISOURCE=3.0mA
0.15
2.85
0.35
V
V
2.65
Overdrive=20mV,
CL=15pF
tPLH
Propagation Delay (Turn-On)
Propagation Delay (Turn-Off)
0.45
0.47
µs
µs
ns
Overdrive=20mV,
CL=15pF
tPHL
tTLH
tTHL
6.1
6.2
Response Time, Output Rise/Fall(4) CL=50pF
Continued on the following page…
© 2010 Fairchild Semiconductor Corporation
FAN156 • Rev. 1.0.0
www.fairchildsemi.com
4
Electrical Characteristics (Continued)
Symbol
Parameter
Condition
Min.
Typ.
Max.
Unit
VDD 1.6V, VSS GND, and TA=+25°C
VHYS
VIO
Input Hysteresis
Input Offset Voltage(2)
VCM=0.5VDD
VCM=0.5VDD
3.5
±1
10
10
mV
mV
pA
pA
V
-15
VSS
45
+15
IIO
Input Offset Current
II
Input Bias Current
VCM
CMRR
IDD
Common Mode Input Voltage
Common Mode Rejection Ratio(3)
Supply Current
VDD
15
VCM=VDD
56
5
dB
µA
dB
PSRR
Power Supply Rejection Ratio(3)
ΔVDD=0.5V
VO=VDD
80
5.5
7.5
0.10
1.50
IOS
Output Short Circuit Current
mA
VO=VSS
VOL
VOH
Low-Level Output Voltage
High-Level Output Voltage
ISINK=1.0mA
ISOURCE=1.0mA
0.25
V
V
1.35
Overdrive=20Mv,
CL=15pF
tPLH
Propagation Delay (Turn-On)
Propagation Delay (Turn-Off)
0.52
0.54
µs
µs
ns
Overdrive=20Mv,
CL=15pF
tPHL
tTLH
tTHL
Notes:
16.5
13.0
Response Time, Output Rise/Fall(4) CL=50pF
2. Differential input switching level is guaranteed at the minimum or maximum offset voltage, minus or plus half the
maximum hysteresis voltage.
3. Guaranteed by design and characterization data.
4. Input signal: 1kHz, square-wave signal with 10ns edge rate.
© 2010 Fairchild Semiconductor Corporation
FAN156 • Rev. 1.0.0
www.fairchildsemi.com
5
Typical Performance Characteristics
8.00
7.50
7.00
6.50
6.00
5.50
900
800
700
600
500
400
300
200
100
0
1.6 VDD
3.0 VDD
5.5 VDD
VDD=1.6V
5.00
VDD=3.0V
4.50
VDD=5.5V
4.00
0.01
Temp. =25C
CL = 15pF
0.1
1
10
100
1000
-55 ⁰C
-40 ⁰C
-25 ⁰C
25 ⁰C
85 ⁰C
95 ⁰C
Frequency (Khz)
TA, Ambient Temperature
Figure 4. Supply Current vs. Temperature
Figure 5. Supply Current vs. Output Transition
Frequency
6
5.5
5
12
10
8
4.5
4
3.5
3
6
‐40 ⁰C
25 ⁰C
85 ⁰C
4
2.5
2
2
VDD=1.6V
0
1.5
VDD=3.0V
0
0.5
1
1.5
2
2.5
3
3.5
4
4.5
5
5.5
6
1
VDD=5.5V
VDD,Supply Voltage (V)
0.5
0
2
4
6
8
10
ISOURCE, OutputSourceCurrent (mA)
Figure 6. Supply Current vs. Supply Voltage
Figure 7. Output HIGH vs. Output Drive Current
400
380
360
340
320
300
1000
100
VDD=1.6V
280
10
1.6VDD
3.0VDD
5.5VDD
VDD=3.0V
260
240
220
VDD=5.5V
1
0.10
1.00
10.00
200
-60
-40
-20
0
20
40
60
80
100
ISINK, Output Sink Current (mA)
Temperature
Figure 8. Output LOW vs. Output Drive Current
Figure 9. Propagation Delay (tPHL) vs. Temperature
© 2010 Fairchild Semiconductor Corporation
FAN156 • Rev. 1.0.0
www.fairchildsemi.com
6
Typical Performance Characteristics (Continued)
300
280
260
240
220
200
180
160
140
120
100
500
450
400
350
tpLH
tpHL
300
1.6VDD
3.0VDD
5.5VDD
250
200
-60
-40
-20
0
20
40
60
80
100
0
50
100
150
200
250
VDD=3.0V
Temperature
Temp. =25°C
Overdrive (mV)
Figure 10.Propagation Delay (tPLH) vs. Temperature
Figure 11. Propagation Delay vs. Input Overdrive
3
TA = 25°C
2
7
6
5
4
3
1
0
‐1
‐2
‐3
2
1
0
VDD
Output
0
50
100
150
200
250
300
1
2
3
4
5
6
Time (µS)
InputOverdrive = 50mV
VS, Supply Voltage (V)
Figure 12. Input Common-Mode Voltage Range vs.
Supply Voltage
Figure 13.Power-Up Delay
© 2010 Fairchild Semiconductor Corporation
FAN156 • Rev. 1.0.0
www.fairchildsemi.com
7
Physical Dimensions
2X
0.05 C
1.45
B
(1)
2X
0.05 C
(0.49)
5X
(0.254)
1.00
(0.75)
(0.52)
1X
TOP VIEW
A
PIN 1 IDENTIFIER
5
0.55MAX
(0.30)
6X
PIN 1
0.05 C
0.05
0.00
RECOMMENED
LAND PATTERN
0.05 C
C
0.45
0.35
0.10
6X
0.00
0.25
6X
0.15
1.0
DETAIL A
0.10
C B A
0.40
0.30
0.05
C
0.35
0.25
5X
5X
0.40
0.30
DETAIL A
PIN 1 TERMINAL
0.075 X 45
CHAMFER
0.5
BOTTOM VIEW
(0.05)
6X
(0.13)
4X
Notes:
1. CONFORMS TO JEDEC STANDARD M0-252 VARIATION UAAD
2. DIMENSIONS ARE IN MILLIMETERS
3. DRAWING CONFORMS TO ASME Y14.5M-1994
4. FILENAME AND REVISION: MAC06AREV4
5. PIN ONE IDENTIFIER IS 2X LENGTH OF ANY
OTHER LINE IN THE MARK CODE LAYOUT.
Figure 14. 6-Lead, MicroPak™, 1.0mm Wide
Package drawings are provided as a service to customers considering Fairchild components. Drawings may change in any manner
without notice. Please note the revision and/or date on the drawing and contact a Fairchild Semiconductor representative to verify or
obtain the most recent revision. Package specifications do not expand the terms of Fairchild’s worldwide terms and conditions, specifically the
warranty therein, which covers Fairchild products.
Always visit Fairchild Semiconductor’s online packaging area for the most recent package drawings:
http://www.fairchildsemi.com/packaging/.
Tape and Reel Specifications
Please visit Fairchild Semiconductor’s online packaging area for the most recent tape and reel specifications:
http://www.fairchildsemi.com/products/logic/pdf/micropak_tr.pdf.
Package Designator
Tape Section
Leader (Start End)
Carrier
Cavity Number
125 (Typical)
5000
Cavity Status Cover Type Status
Empty
Filled
Sealed
Sealed
Sealed
L6X
Trailer (Hub End)
75 (Typical)
Empty
© 2010 Fairchild Semiconductor Corporation
FAN156 • Rev. 1.0.0
www.fairchildsemi.com
8
© 2010 Fairchild Semiconductor Corporation
FAN156 • Rev. 1.0.0
www.fairchildsemi.com
9
相关型号:
FAN1581DX_NL
Adjustable Positive LDO Regulator, 1.25V Min, 5.7V Max, 0.6V Dropout, PSSO5, LEAD FREE, PLASTIC, TO-252, DPAK-5
FAIRCHILD
©2020 ICPDF网 联系我们和版权申明