BC846B [FAIRCHILD]
NPN General Purpose Amplifier; NPN通用放大器型号: | BC846B |
厂家: | FAIRCHILD SEMICONDUCTOR |
描述: | NPN General Purpose Amplifier |
文件: | 总12页 (文件大小:394K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
BC846A
BC846B
BC847A
BC847B
BC847C
C
C
E
E
B
B
SOT-23
Mark: 1A. / 1B.
SOT-23
Mark: 1E. / 1F. / 1G.
NPN General Purpose Amplifier
This device is designed for low noise, high gain, general purpose
amplifier applications at collector currents from 1.0 µA to 50 mA.
Sourced from Process 07.
3
Absolute Maximum Ratings*
TA = 25°C unless otherwise noted
Symbol
Parameter
Value
Units
VCEO
Collector-Emitter Voltage
Collector-Base Voltage
65
45
80
50
6.0
V
V
V
V
V
BC846 series
BC847 series
BC846 series
BC847 series
VCES
VEBO
IC
Emitter-Base Voltage
Collector Current - Continuous
100
mA
Operating and Storage Junction Temperature Range
-55 to +150
C
°
TJ, Tstg
*These ratings are limiting values above which the serviceability of any semiconductor device may be impaired.
NOTES:
1) These ratings are based on a maximum junction temperature of 150 degrees C.
2) These are steady state limits. The factory should be consulted on applications involving pulsed or low duty cycle operations.
Thermal Characteristics
TA = 25°C unless otherwise noted
Symbol
Characteristic
Max
Units
*BC846 / BC847
PD
Total Device Dissipation
Derate above 25 C
325
2.8
mW
mW/ C
°
°
Thermal Resistance, Junction to Ambient
357
Rθ
C/W
°
JA
*Device mounted on FR-4 PCB 40 mm X 40 mm X 1.5 mm.
1997 Fairchild Semiconductor Corporation
NPN General Purpose Amplifier
(continued)
Electrical Characteristics
TA = 25°C unless otherwise noted
Symbol
Parameter
Test Conditions
Min
Max
Units
OFF CHARACTERISTICS
V(BR)CEO
Collector-Emitter Breakdown
Voltage
Collector-Base Breakdown Voltage
65
45
80
50
V
V
V
IC = 10 mA, IB = 0 846A / B
847A / B
V(BR)CES
IC = 10 µA, IE = 0
846A / B
847A / B
V(BR)EBO
ICBO
Emitter-Base Breakdown Voltage
Collector-Cutoff Current
6.0
IE = 10 µA, IC = 0
VCB = 30 V
15
nA
5.0
VCB = 30 V, TA = 150°C
µA
ON CHARACTERISTICS
hFE
DC Current Gain
IC = 2.0 mA, VCE = 5.0 V
110
200
420
220
450
800
846A / 847A
846B / 847B
847C
Collector-Emitter Saturation Voltage IC = 10 mA, IB = 0.5 mA
IC = 100 mA, IB = 5.0 mA
0.25
0.6
0.70
0.77
V
V
V
V
VCE(sat)
VBE(on)
Base-Emitter On Voltage
IC = 2.0 mA, VCE = 5.0 V
IC = 10 mA, VCE = 5.0 V
0.58
100
SMALL SIGNAL CHARACTERISTICS
Current Gain - Bandwidth Product
IC = 10 mA, VCE = 5.0,
f = 100 MHz
MHz
fT
Output Capacitance
Noise Figure
VCB = 10 V, f = 1.0 MHz
4.5
10
pF
dB
Cobo
NF
IC = 0.2 mA, VCE = 5.0,
RS = 2.0 k , f = 1.0 kHz,
Ω
BW = 200 Hz
Typical Characteristics
Typical Pulsed Current Gain
Collector-Emitter Saturation
Voltage vs Collector Current
vs Collector Current
1200
0.3
0.25
0.2
VCE = 5.0 V
125 °C
1000
800
600
400
200
0
β = 10
125 °C
0.15
0.1
25 °C
25 °C
- 40 °C
- 40 °C
0.05
0.01 0.03 0.1 0.3
1
3
10
30
100
0.1
1
10
100
IC - COLLECTOR CURRENT (mA)
IC - COLLECTOR CURRENT (mA)
NPN General Purpose Amplifier
(continued)
Typical Characteristics
Base-Emitter Saturation
Voltage vs Collector Current
Base-Emitter ON Voltage vs
Collector Current
1
1
0.8
0.6
0.4
0.2
- 40 °C
- 40 °C
0.8
25 °C
25 °C
0.6
125 °C
125 °C
0.4
β = 10
VCE = 5.0 V
0.2
0.1
1
10
100
0.1
1
10
40
IC - COLLECTOR CURRENT (mA)
I C - COLLECTOR CURRENT (mA)
Collector-Cutoff Current
vs Ambient Temperature
Input and Output Capacitance
vs Reverse Bias Voltage
10
5
4
3
2
1
0
f = 1.0 MHz
VCB = 45V
3
C
te
1
C
ob
0.1
0
4
8
12
16
20
25
50
75
100
125
150
REVERSE BIAS VOLTAGE (V)
TA - AMBIE NT TEMP ERATURE ( C)
°
Normalized Collector-Cutoff Current
vs Ambient Temperature
Wideband Noise Frequency
vs Source Resistance
1000
5
VCE = 5.0 V
BANDWIDTH = 15.7 kHz
4
3
2
1
0
100
10
1
I
= 100 µA
C
I
= 30 µA
C
I
= 10 µA
C
25
50
75
100
125
150
1,000
2,000
5,000
10,000
20,000
50,000
100,000
TA - AMBIENT TEMPERATURE ( C)
°
R
- SOURCE RESISTANCE (Ω )
S
NPN General Purpose Amplifier
(continued)
Typical Characteristics (continued)
Contours of Constant Gain
Bandwidth Product (fT )
Noise Figure vs Frequency
10
I
R
= 200 µA,
= 10 kΩ
C
10
7
S
8
6
4
2
175 MHz
I
= 100 µA,
C
R
= 10 kΩ
S
5
I
= 1.0 mA,
C
R
= 500 Ω
150 MHz
S
3
2
I
= 1.0 mA,
C
R
= 5.0 kΩ
S
125 MHz
100 MHz
75 MHz
V
= 5.0V
CE
1
0
0.1
1
10
100
0.0001 0.001
0.01
0.1
1
10
100
I C - COLLECTOR CURRENT (mA)
f - FREQUENCY (MHz)
Contours of Constant
Narrow Band Noise Figure
Contours of Constant
Narrow Band Noise Figure
10,000
5,000
10,000
5,000
3.0 d
B
4.0 d
B
2.0 d
B
2,000
1,000
500
2,000
1,000
500
3.0 d
B
6.0 d
B
4.0 d
B
8.0 d
B
V CE = 5.0 V
V CE = 5.0 V
f = 1.0 kHz
BANDWIDTH
= 200 Hz
6.0 dB
8.0 d
10 d
B
f = 100 Hz
BANDWIDTH
= 20 Hz
B
200
100
200
100
12 d
B
14 d
B
1
10
100
1,000
1
10
100
1,000
I
- COLLECTOR CURRENT ( A)
µ
I
- COLLECTOR CURRENT ( µ A)
C
C
Contours of Constant
Contours of Constant
Narrow Band Noise Figure
Narrow Band Noise Figure
10000
5000
10000
5000
1.0 d
B
2.0 d
B
2000
1000
500
2.0 d
B
2000
1000
500
3.0 d
B
3.0 d
B
4.0 d
B
VCE
5.0V
f = 1.0 MHz
BANDWIDTH
= 200kHz
=
4.
0 dB
5.0
dB
6.0
VCE = 5.0V
f = 10kHz
BANDWIDTH
= 2.0kHz
6.0 d
B
200
100
200
100
dB
7.0 d
8.0 d
B
B
8.0 d
B
1
10
100
1000
0.01
0.1
1
10
µ
I C - COLLECTOR CURRENT ( A)
µ
I C - COLLECTOR CURRENT ( A)
NPN General Purpose Amplifier
(continued)
Typical Common Emitter Characteristics (f = 1.0 kHz)
Typical Common Emitter Characteristics
1.4
Typical Common Emitter Characteristics
1.5
h
fe
1.4
h ie
VCE = 5.0V
f = 1.0kHz
1.3
h re
h fe
h oe
1.3
h
ie
I C = 1.0mA
1.2
1.1
1
h
oe
1.2
1.1
1
h
h
re
oe
0.9
0.8
0.7
0.6
0.5
h
h
re
ie
h oe
h fe
h re
IC = 1.0mA
f = 1.0kHz
TA = 25 C
0.9
0.8
h ie
h
fe
°
-100
-50
0
50
100
150
0
5
10
15
20
25
T J - JUNCTIO N TEMP ERATURE ( C)
V CE - COLLECTOR VOLTAGE (V)
°
Typical Common Emitter Characteristics
100
f = 1.0kHz
h
oe
10
1
h
and h
re
ie
h
re
h
oe
3
h
fe
h
fe
h
ie
0.1
0.01
0.1 0.2
0.5
1
2
5
10 20
50 100
I C - COLLECTOR CURRENT (mA)
SOT-23 Tape and Reel Data
SOT-23 Packaging
Configuration: Figure 1.0
Packaging Description:
Customized Label
SOT-23 parts are shipped in tape. The carrier tape is
made from
a dissipative (carbon filled) polycarbonate
resin. The cover tape is a multilayer film (Heat Activated
Adhesive in nature) primarily composed of polyester film,
adhesive layer, sealant, and anti-static sprayed agent.
These reeled parts in standard option are shipped with
3,000 units per 7" or 177cm diameter reel. The reels are
dark bluein color and is madeof polystyrene plastic (anti-
static coated). Other option comes in 10,000 units per 13"
or 330cm diameter reel. This and some other options are
described in the Packaging Information table.
Antistatic Cover Tape
These full reels areindividually labeled and placed inside
a
standard intermediate made of recyclable corrugated
brown paper with aFairchild logo printing. One pizza box
contains eight reels maximum. And these intermediate
boxes are placed inside a labeled shipping box which
comesin different sizes depending on the number of parts
shipped.
Human Readable
Label
Embossed
CarrierTape
3P
3P
3P
3P
SOT-23 PackagingInformation
Standard
(no flow code)
PackagingOption
D87Z
Packagingtype
TNR
TNR
10,000
13"
SOT-23 Unit Orientation
Qty per Reel/Tube/Bag
Reel Size
3,000
7" Dia
Box Dimension (mm)
Max qty per Box
187x107x183 343x343x64
343mmx 342mmx 64mm
Intermediate box for L87Z Option
Human Readable Label
24,000
0.0082
0.1175
30,000
0.0082
0.4006
Weight per unit (gm)
Weight per Reel (kg)
Note/Comments
Human Readable Label sample
Human readable
Label
187mmx 107mmx 183mm
SOT-23 Tape Leader and Trailer
IntermediateBox forStandard Option
Configuration: Figure 2.0
Carrier Tape
Cover Tape
Components
Trailer Tape
Leader Tape
300mm minimumor
75 empty pockets
500mm minimumor
125 empty pockets
September 1999, Rev. C
©2000 Fairchild Semiconductor International
SOT-23 Tape and Reel Data, continued
SOT-23 Embossed Carrier Tape
Configuration: Figure 3.0
P0
P2
D0
D1
T
E1
E2
W
F
Wc
B0
Tc
K0
A0
P1
User Direction of Feed
Dimensions are in millimeter
E1 E2
A0
B0
W
D0
D1
F
P1
P0
K0
T
Wc
5.2
Tc
Pkg type
SOT-23
(8mm)
3.15
+/-0.10
2.77
+/-0.10
8.0
+/-0.3
1.55
+/-0.05
1.125
1.75
+/-0.10
6.25
min
3.50
+/-0.05
4.0
+/-0.1
4.0
+/-0.1
1.30
+/-0.10
0.228
+/-0.013
0.06
+/-0.02
+/-0.125
+/-0.3
Notes: A0, B0, and K0 dimensions are determined with respect to the EIA/Jedec RS-481
rotational and lateral movement requirements (see sketches A, B, and C).
0.5mm
maximum
20 deg maximum
Typical
component
cavity
center line
0.5mm
maximum
B0
20 deg maximum component rotation
Typical
component
center line
Sketch A (Side or Front Sectional View)
Component Rotation
Sketch C (Top View)
Component lateral movement
A0
Sketch B (Top View)
Component Rotation
SOT-23 Reel Configuration: Figure 4.0
W1 Measured at Hub
Dim A
Max
Dim A
max
See detail AA
Dim N
7"Diameter Option
B Min
Dim C
See detail AA
Dim D
min
W3
13" Diameter Option
W2 max Measured at Hub
DETAIL AA
Dim W2
Dimensions are in inches and millimeters
Reel
Option
Tape Size
8mm
Dim A
Dim B
Dim C
Dim D
Dim N
Dim W1
Dim W3 (LSL-USL)
7.00
177.8
0.059
1.5
512 +0.020/-0.008
13 +0.5/-0.2
0.795
20.2
2.165
55
0.331 +0.059/-0.000
8.4 +1.5/0
0.567
14.4
0.311 – 0.429
7.9 – 10.9
7" Dia
13.00
330
0.059
1.5
512 +0.020/-0.008
13 +0.5/-0.2
0.795
20.2
4.00
100
0.331 +0.059/-0.000
8.4 +1.5/0
0.567
14.4
0.311 – 0.429
7.9 – 10.9
8mm
13" Dia
September 1999, Rev. C
SOT-23 Package Dimensions
SOT-23 (FS PKG Code 49)
1:1
Scale 1:1 on letter size paper
Dimensions shown below are in:
inches [millimeters]
Part Weight per unit (gram): 0.0082
September 1998, Rev. A1
©2000 Fairchild Semiconductor International
SOT-23 Tape and Reel Data
SOT-23 Packaging
Configuration: Figure 1.0
Packaging Description:
Customized Label
SOT-23 parts are shipped in tape. The carrier tape is
made from
a dissipative (carbon filled) polycarbonate
resin. The cover tape is a multilayer film (Heat Activated
Adhesive in nature) primarily composed of polyester film,
adhesive layer, sealant, and anti-static sprayed agent.
These reeled parts in standard option are shipped with
3,000 units per 7" or 177cm diameter reel. The reels are
dark bluein color and is madeof polystyrene plastic (anti-
static coated). Other option comes in 10,000 units per 13"
or 330cm diameter reel. This and some other options are
described in the Packaging Information table.
Antistatic Cover Tape
These full reels areindividually labeled and placed inside
a
standard intermediate made of recyclable corrugated
brown paper with aFairchild logo printing. One pizza box
contains eight reels maximum. And these intermediate
boxes are placed inside a labeled shipping box which
comesin different sizes depending on the number of parts
shipped.
Human Readable
Label
Embossed
CarrierTape
3P
3P
3P
3P
SOT-23 PackagingInformation
Standard
(no flow code)
PackagingOption
D87Z
Packagingtype
TNR
TNR
10,000
13"
SOT-23 Unit Orientation
Qty per Reel/Tube/Bag
Reel Size
3,000
7" Dia
Box Dimension (mm)
Max qty per Box
187x107x183 343x343x64
343mmx 342mmx 64mm
Intermediate box for L87Z Option
Human Readable Label
24,000
0.0082
0.1175
30,000
0.0082
0.4006
Weight per unit (gm)
Weight per Reel (kg)
Note/Comments
Human Readable Label sample
Human readable
Label
187mmx 107mmx 183mm
SOT-23 Tape Leader and Trailer
IntermediateBox forStandard Option
Configuration: Figure 2.0
Carrier Tape
Cover Tape
Components
Trailer Tape
Leader Tape
300mm minimumor
75 empty pockets
500mm minimumor
125 empty pockets
September 1999, Rev. C
©2000 Fairchild Semiconductor International
SOT-23 Tape and Reel Data, continued
SOT-23 Embossed Carrier Tape
Configuration: Figure 3.0
P0
P2
D0
D1
T
E1
E2
W
F
Wc
B0
Tc
K0
A0
P1
User Direction of Feed
Dimensions are in millimeter
E1 E2
A0
B0
W
D0
D1
F
P1
P0
K0
T
Wc
5.2
Tc
Pkg type
SOT-23
(8mm)
3.15
+/-0.10
2.77
+/-0.10
8.0
+/-0.3
1.55
+/-0.05
1.125
1.75
+/-0.10
6.25
min
3.50
+/-0.05
4.0
+/-0.1
4.0
+/-0.1
1.30
+/-0.10
0.228
+/-0.013
0.06
+/-0.02
+/-0.125
+/-0.3
Notes: A0, B0, and K0 dimensions are determined with respect to the EIA/Jedec RS-481
rotational and lateral movement requirements (see sketches A, B, and C).
0.5mm
maximum
20 deg maximum
Typical
component
cavity
center line
0.5mm
maximum
B0
20 deg maximum component rotation
Typical
component
center line
Sketch A (Side or Front Sectional View)
Component Rotation
Sketch C (Top View)
Component lateral movement
A0
Sketch B (Top View)
Component Rotation
SOT-23 Reel Configuration: Figure 4.0
W1 Measured at Hub
Dim A
Max
Dim A
max
See detail AA
Dim N
7"Diameter Option
B Min
Dim C
See detail AA
Dim D
min
W3
13" Diameter Option
W2 max Measured at Hub
DETAIL AA
Dim W2
Dimensions are in inches and millimeters
Reel
Option
Tape Size
8mm
Dim A
Dim B
Dim C
Dim D
Dim N
Dim W1
Dim W3 (LSL-USL)
7.00
177.8
0.059
1.5
512 +0.020/-0.008
13 +0.5/-0.2
0.795
20.2
2.165
55
0.331 +0.059/-0.000
8.4 +1.5/0
0.567
14.4
0.311 – 0.429
7.9 – 10.9
7" Dia
13.00
330
0.059
1.5
512 +0.020/-0.008
13 +0.5/-0.2
0.795
20.2
4.00
100
0.331 +0.059/-0.000
8.4 +1.5/0
0.567
14.4
0.311 – 0.429
7.9 – 10.9
8mm
13" Dia
September 1999, Rev. C
SOT-23 Package Dimensions
SOT-23 (FS PKG Code 49)
1:1
Scale 1:1 on letter size paper
Dimensions shown below are in:
inches [millimeters]
Part Weight per unit (gram): 0.0082
September 1998, Rev. A1
©2000 Fairchild Semiconductor International
TRADEMARKS
The following are registered and unregistered trademarks Fairchild Semiconductor owns or is authorized to use and is
not intended to be an exhaustive list of all such trademarks.
PowerTrench
QFET™
QS™
SyncFET™
TinyLogic™
UHC™
ACEx™
FASTr™
GlobalOptoisolator™
GTO™
Bottomless™
CoolFET™
CROSSVOLT™
DOME™
QT Optoelectronics™
VCX™
HiSeC™
Quiet Series™
SILENT SWITCHER
SMART START™
SuperSOT™-3
SuperSOT™-6
SuperSOT™-8
ISOPLANAR™
MICROWIRE™
OPTOLOGIC™
OPTOPLANAR™
PACMAN™
POP™
E2CMOSTM
EnSignaTM
FACT™
FACT Quiet Series™
FAST
DISCLAIMER
FAIRCHILD SEMICONDUCTOR RESERVES THE RIGHT TO MAKE CHANGES WITHOUT FURTHER
NOTICE TOANY PRODUCTS HEREIN TO IMPROVE RELIABILITY, FUNCTION OR DESIGN. FAIRCHILD
DOES NOTASSUMEANY LIABILITYARISING OUT OF THEAPPLICATION OR USE OFANY PRODUCT
OR CIRCUIT DESCRIBED HEREIN; NEITHER DOES IT CONVEY ANY LICENSE UNDER ITS PATENT
RIGHTS, NOR THE RIGHTS OF OTHERS.
LIFE SUPPORT POLICY
FAIRCHILD’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT
DEVICES OR SYSTEMS WITHOUTTHE EXPRESS WRITTENAPPROVALOF FAIRCHILD SEMICONDUCTOR CORPORATION.
As used herein:
1. Life support devices or systems are devices or
systems which, (a) are intended for surgical implant into
the body, or (b) support or sustain life, or (c) whose
failure to perform when properly used in accordance
with instructions for use provided in the labeling, can be
reasonably expected to result in significant injury to the
user.
2. A critical component is any component of a life
support device or system whose failure to perform can
be reasonably expected to cause the failure of the life
support device or system, or to affect its safety or
effectiveness.
PRODUCT STATUS DEFINITIONS
Definition of Terms
Datasheet Identification
Product Status
Definition
Advance Information
Formative or
In Design
This datasheet contains the design specifications for
product development. Specifications may change in
any manner without notice.
Preliminary
First Production
This datasheet contains preliminary data, and
supplementary data will be published at a later date.
Fairchild Semiconductor reserves the right to make
changes at any time without notice in order to improve
design.
No Identification Needed
Obsolete
Full Production
This datasheet contains final specifications. Fairchild
Semiconductor reserves the right to make changes at
any time without notice in order to improve design.
Not In Production
This datasheet contains specifications on a product
that has been discontinued by Fairchild semiconductor.
The datasheet is printed for reference information only.
Rev. G
相关型号:
BC846B-TAPE-13
TRANSISTOR 100 mA, 65 V, NPN, Si, SMALL SIGNAL TRANSISTOR, BIP General Purpose Small Signal
NXP
BC846B-TAPE-7
TRANSISTOR 100 mA, 65 V, NPN, Si, SMALL SIGNAL TRANSISTOR, BIP General Purpose Small Signal
NXP
©2020 ICPDF网 联系我们和版权申明