74ACTQ32 [FAIRCHILD]
Quiet Series Quad 2-Input OR Gate; 宁静系列四2输入或门
| 型号： | 74ACTQ32 |
| 厂家： | 
FAIRCHILD SEMICONDUCTOR |
| 描述： | Quiet Series Quad 2-Input OR Gate |
| 文件： | 总7页 (文件大小：156K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
March 1993
Revised September 2000
74ACTQ32
Quiet Series Quad 2-Input OR Gate
General Description
Features
The ACTQ320 contains four, 2-input OR gates and utilizes
Fairchild Quiet Series technology to guarantee quiet output
switching and improved dynamic threshold performance.
FACT Quiet Series features GTO output control and
undershoot corrector in addition to a split ground bus for
superior ACMOS performance.
■ ICC reduced by 50%
■ Guaranteed simultaneous switching noise level and
dynamic threshold performance
■ Improved latch-up immunity
■ Minimum 4 kV ESD protection
■ TTL-compatible inputs
■ Outputs source/sink 24 mA
Ordering Code:
Order Number Package Number
Package Description
74ACT32SC
74ACT32SJ
74ACT32PC
M14A
M14D
N14A
14-Lead Small Outline Integrated Circuit (SOIC), JEDEC MS-120, 0.150 Narrow
14-Lead Small Outline Package (SOP), EIAJ TYPE II, 5.3mm Wide
14-Lead Plastic Dual-In-Line Package (PDIP), JEDEC MS-001, 0.300 Wide
Device also available in Tape and Reel. Specify by appending suffix letter “X” to the ordering code.
Logic Symbol
Connection Diagram
IEEE/IEC
Pin Descriptions
Pin Names
An, Bn
On
Descriptions
Inputs
Outputs
FACT , FACT Quiet Series , and GTO are trademarks of Fairchild Semiconductor Corporation.
© 2000 Fairchild Semiconductor Corporation
DS010893
www.fairchildsemi.com
Absolute Maximum Ratings(Note 1)
Recommended Operating
Conditions
Supply Voltage (VCC
)
−0.5V to +7.0V
DC Input Diode Current (IIK
VI = −0.5V
)
Supply Voltage (VCC
)
4.5V to 5.5V
0V to VCC
−20 mA
+20 mA
Input Voltage (VI)
VI = VCC + 0.5V
Output Voltage (VO)
0V to VCC
DC Input Voltage (VI)
−0.5V to VCC + 0.5V
Operating Temperature (TA)
−40°C to +85°C
DC Output Diode Current (IOK
)
Minimum Input Edge Rate (∆V/∆t)
V
V
O = −0.5V
−20 mA
+20 mA
V
IN from 0.8V to 2.0V
O = VCC + 0.5V
VCC @ 4.5V, 5.5V
125 mV/ns
DC Output Voltage (VO)
−0.5V to VCC + 0.5V
± 50 mA
DC Output Source or Sink Current (IO)
DC VCC or Ground Current
Note 1: Absolute maximum ratings are values beyond which damage to the
device may occur. The databook specifications should be met, without
exception, to ensure that the system design is reliable over its power sup-
ply, temperature, and output/input loading variables. Fairchild does not rec-
ommend operation of FACT circuits outside of databook specifications.
per Output Pin (ICC or IGND
)
± 50 mA
−65°C to +150°C
± 300 mA
Storage Temperature (TSTG
)
DC Latch-Up Source or Sink Current
Junction Temperature (TJ) PDIP
140°C
DC Electrical Characteristics
VCC
T
A = +25°C
T
A = −55°C to +125°C
TA = −40°C to +85°C
Symbol
VIH
Parameter
Units
Conditions
(V)
4.5
5.5
4.5
5.5
4.5
5.5
Typ
1.5
Guaranteed Limits
Minimum HIGH Level
Input Voltage
2.0
2.0
0.8
0.8
4.4
5.4
2.0
2.0
0.8
0.8
4.4
5.4
2.0
2.0
0.8
0.8
4.4
5.4
V
OUT = 0.1V
or VCC − 0.1V
OUT = 0.1V
or VCC − 0.1V
V
V
V
1.5
VIL
Maximum LOW Level
Input Voltage
1.5
V
1.5
VOH
Minimum HIGH Level
Output Voltage
4.49
5.49
I
OUT = −50 µA
IN = VIL or VIH
V
4.5
5.5
4.5
5.5
3.86
4.86
0.1
3.70
4.70
0.1
3.76
4.76
0.1
V
V
V
I
I
OH = − 24 mA
OH = − 24 mA (Note 2)
VOL
Maximum LOW Level
Output Voltage
0.001
0.001
I
OUT = 50 µA
0.1
0.1
0.1
V
IN = VIL or VIH
4.5
5.5
0.36
0.36
0.50
0.50
±1.0
0.44
0.44
I
I
OL = 24 mA
OL = 24 mA (Note 2)
IIN
Maximum Input
5.5
± 0.1
± 1.0
µA VI = VCC, GND
mA VI = VCC − 2.1V
Leakage Current
ICCT
IOLD
IOHD
ICC
Maximum ICC/Input
Minimum Dynamic
Output Current (Note 3)
Maximum Quiescent
Supply Current
5.5
5.5
5.5
0.6
1.6
50
1.5
75
mA
mA
V
V
V
OLD = 1.65V Max
OHD = 3.85V Min
IN = VCC
−50
40.0
−75
5.5
5.0
5.0
5.0
5.0
2.0
1.5
20.0
µA
V
or GND
VOLP
VOLV
VIHD
VILD
Quiet Output Maximum
Dynamic VOL
Figures 1, 2
(Note 4)(Note 5)
Figures 1, 2
(Note 4)(Note 5)
1.1
−0.6
1.9
Quiet Output
−1.2
2.2
V
Minimum Dynamic VOL
Minimum HIGH Level
Dynamic Input Voltage
Maximum LOW Level
Dynamic Input Voltage
V
(Note 4)(Note 6)
(Note 4)(Note 6)
1.2
0.8
V
Note 2: All outputs loaded; thresholds on input associated with output under test.
Note 3: Maximum test duration 2.0 ms, one output loaded at a time.
Note 4: DIP Package.
Note 5: Max number of outputs defined as (n). Data inputs are 0V to 3V. One output @ GND.
Note 6: Max number of data inputs (n) switching. (n-1) inputs switching 0V to 3V (ACTQ). Input-under-test switching: 3V to threshold (VILD),
0V to threshold (VIHD), f = 1 MHZ.
www.fairchildsemi.com
2
AC Electrical Characteristics
VCC
T
A = +25°C
T
A = −40°C to +85°C
L = 50 pF
Max
Symbol
Parameter
C
L = 50 pF
C
Units
(V)
(Note 7)
Min
Typ
Max
Min
tPLH
Propagation Delay
5.0
5.0
5.0
2.5
6.0
6.0
0.5
6.5
2.5
2.5
7.0
7.0
1.0
ns
ns
ns
Data to Output
Propagation Delay
Data to Output
Output to Output
Skew (Note 8)
tPHL
2.0
6.5
1.0
tOSHL
tOSLH
Note 7: Voltage Range 5.0 is 5.0V ± 0.5V.
Note 8: Skew is defined as the absolute value of the difference between the actual propagation delay for any two separate outputs of the same device. The
specification applies to any outputs switching in the same direction, either HIGH-to-LOW (tOSHL) or LOW-to-HIGH (tOSLH). Parameter guaranteed by design.
Capacitance
Symbol
CIN
CPD
Parameter
Input Capacitance
Power Dissipation Capacitance
Typ
4.5
68
Units
pF
Conditions
V
CC = OPEN
CC = 5.0V
pF
V
3
www.fairchildsemi.com
FACT Noise Characteristics
The setup of a noise characteristics measurement is critical
to the accuracy and repeatability of the tests. The following
is a brief description of the setup used to measure the
noise characteristics of FACT.
VOLP/VOLV and VOHP/VOHV:
•
Determine the quiet output pin that demonstrates the
greatest noise levels. The worst case pin will usually be
the furthest from the ground pin. Monitor the output volt-
ages using a 50Ω coaxial cable plugged into a standard
SMB type connector on the test fixture. Do not use an
active FET probe.
Equipment
Hewlett Packard Model 8180A Word Generator
PC-163A Test Fixture
•
•
Measure VOLP and VOLV on the quiet output during the
Tektronics Model 7854 Oscilloscope
Procedure:
worst case transition for active and enable. Measure
VOHP and VOHV on the quiet output during the worst
1. Verify Test Fixture Loading: Standard Load 50 pF,
case transition.
500Ω.
Verify that the GND reference recorded on the oscillo-
scope has not drifted to ensure the accuracy and repeat-
ability of the measurements.
2. Deskew the HFS generator so that no two channels
have greater than 150 ps skew between them. This
requires that the oscilloscope be deskewed first. It is
important to deskew the HFS generator channels
before testing. This will ensure that the outputs switch
simultaneously.
V
ILD and VIHD:
•
Monitor one of the switching outputs using a 50Ω coaxial
cable plugged into a standard SMB type connector on
the test fixture. Do not use an active FET probe.
3. Terminate all inputs and outputs to ensure proper load-
ing of the outputs and that the input levels are at the
correct voltage.
•
•
•
First increase the input LOW voltage level, VIL, until the
output begins to oscillate or steps out a min of 2 ns.
Oscillation is defined as noise on the output LOW level
that exceeds VIL limits, or on output HIGH levels that
4. Set the HFS generator to toggle all but one output at a
frequency of 1 MHz. Greater frequencies will increase
DUT heating and effect the results of the measure-
ment.
exceed VIH limits. The input LOW voltage level at which
oscillation occurs is defined as VILD
.
Next decrease the input HIGH voltage level, VIH, until
the output begins to oscillate or steps out a min of 2 ns.
Oscillation is defined as noise on the output LOW level
that exceeds VIL limits, or on output HIGH levels that
exceed VIH limits. The input HIGH voltage level at which
oscillation occurs is defined as VIHD
.
Verify that the GND reference recorded on the oscillo-
scope has not drifted to ensure the accuracy and repeat-
ability of the measurements.
VOHV and VOLP are measured with respect to ground reference.
Input pulses have the following characteristics: f = 1 MHz, tr = 3 ns, tf
3 ns, skew < 150 ps.
=
FIGURE 1. Quiet Output Noise Voltage Waveforms
5. Set the HFS generator input levels at 0V LOW and 3V
HIGH for ACTQ devices and 0V LOW and 5V HIGH for
AC devices. Verify levels with an oscilloscope.
FIGURE 2. Simultaneous Switching Test Circuit
www.fairchildsemi.com
4
Physical Dimensions inches (millimeters) unless otherwise noted
14-Lead Small Outline Integrated Circuit (SOIC), JEDEC MS-120, 0.150 Narrow
Package Number M14A
5
www.fairchildsemi.com
Physical Dimensions inches (millimeters) unless otherwise noted (Continued)
14-Lead Small Outline Package (SOP), EIAJ TYPE II, 5.3mm Wide
Package Number M14D
www.fairchildsemi.com
6
Physical Dimensions inches (millimeters) unless otherwise noted (Continued)
14-Lead Plastic Dual-In-Line Package (PDIP), JEDEC MS-001, 0.300 Wide
Package Number N14A
Fairchild does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and
Fairchild reserves the right at any time without notice to change said circuitry and specifications.
LIFE SUPPORT POLICY
FAIRCHILD’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT
DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT OF FAIRCHILD
SEMICONDUCTOR CORPORATION. As used herein:
1. Life support devices or systems are devices or systems
which, (a) are intended for surgical implant into the
body, or (b) support or sustain life, and (c) whose failure
to perform when properly used in accordance with
instructions for use provided in the labeling, can be rea-
sonably expected to result in a significant injury to the
user.
2. A critical component in any component of a life support
device or system whose failure to perform can be rea-
sonably expected to cause the failure of the life support
device or system, or to affect its safety or effectiveness.
www.fairchildsemi.com
7
www.fairchildsemi.com
相关型号：
74ACTQ32SCX_NL
OR Gate, ACT Series, 4-Func, 2-Input, CMOS, PDSO14, 0.150 INCH, MS-120, SOIC-14
FAIRCHILD
©2020 ICPDF网 联系我们和版权申明