XRP6124HVESTR0.5-F [EXAR]
Non-Synchronous PFET Step-Down Controller; 非同步PFET降压控制器![XRP6124HVESTR0.5-F](http://pdffile.icpdf.com/pdf1/p00188/img/icpdf/XRP612_1061779_icpdf.jpg)
型号: | XRP6124HVESTR0.5-F |
厂家: | ![]() |
描述: | Non-Synchronous PFET Step-Down Controller |
文件: | 总12页 (文件大小:481K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
![](http://public.icpdf.com/style/img/ads.jpg)
XRP6124
Non-Synchronous PFET Step-Down Controller
January 2011
Rev. 1.1.0
GENERAL DESCRIPTION
APPLICATIONS
The XRP6124 is a non synchronous step down
(buck) controller for up to 5Amps point of
loads. A wide 3V to 30V input voltage range
allows for single supply operations from
industry standard 3.3V, 5V, 12V and 24V
power rails.
• Point of Load Conversions
• Audio-Video Equipments
• Industrial and Medical Equipments
• Distributed Power Architecture
With a proprietary Constant On-Time (COT)
control scheme, the XRP6124 provides
extremely fast line and load transient response
while the operating frequency remains nearly
constant. It requires no loop compensation
hence simplifying circuit implementation and
reducing overall component count. The
XRP76124 also implements an emulated ESR
circuitry allowing usage of ceramic output
capacitors and insuring stable operations
without the use of extra external components.
FEATURES
• 5A Point-of-Load Capable
− Down to 1.2V Output Voltage Conversion
• Wide Input Voltage Range
− 3V to 18V: XRP6124
− 4.5V to 30V: XRP6124HV
• Constant On-Time Operations
− Constant Frequency Operations
− No External Compensation
Built-in soft start prevents high inrush currents
while under voltage lock-out and output short
protections insure safe operations under
abnormal operating conditions.
− Supports Ceramic Output Capacitors
• Built-in 2ms Soft Start
• Short Circuit Protection
• <1µA shutdown current
The XRP6124 is available in a RoHS compliant,
green/halogen free space-saving 5-pin SOT23
package.
• RoHS Compliant, Green/Halogen Free
5-pin SOT23 Package
TYPICAL APPLICATION DIAGRAM
Figure 1: XRP6124 Application Diagram
Exar Corporation
www.exar.com
48720 Kato Road, Fremont CA 94538, USA
Tel. +1 510 668-7000 – Fax. +1 510 668-7001
XRP6124
Non-Synchronous PFET Step-Down Controller
ABSOLUTE MAXIMUM RATINGS
OPERATING RATINGS
These are stress ratings only and functional operation of
the device at these ratings or any other above those
indicated in the operation sections of the specifications
below is not implied. Exposure to absolute maximum
rating conditions for extended periods of time may affect
reliability.
Input Voltage Range VIN (XRP6124)................3.0V to 18V
Input Voltage Range VIN (XRP6124HV)............4.5V to 30V
Junction Temperature Range....................-40°C to 125°C
Thermal Resistance θJA .....................................191°C/W
VIN (XRP6124)............................................-0.3V to 20V
VIN (XRP6124HV)........................................-0.3V to 32V
GATE ......................................................VIN-GATE<8V
FB, EN .....................................................-0.3V to 5.5V
Storage Temperature.............................. -65°C to 150°C
Power Dissipation................................ Internally Limited
Lead Temperature (Soldering, 10 sec) ...................300°C
ESD Rating (HBM - Human Body Model).................... 2kV
ELECTRICAL SPECIFICATIONS
Specifications are for an Operating Junction Temperature of TJ = 25°C only; limits applying over the full Operating Junction
Temperature range are denoted by a “•”. Minimum and Maximum limits are guaranteed through test, design, or statistical
correlation. Typical values represent the most likely parametric norm at TJ = 25°C, and are provided for reference purposes
only. Unless otherwise indicated, VIN = 3.0V to 18V, TJ = –40°C to 125°C.
Parameter
Min.
Typ.
Max.
Units
Conditions
UVLO Turn-On Threshold
UVLO Turn-On Threshold
UVLO Hysteresis
2.5
3.8
2.8
4.2
0.1
3.0
4.5
V
V
•
•
XRP6124
XRP6124HV
V
3.0
4.5
18
30
V
•
•
XRP6124
Operating Input Voltage Range
V
XRP6124HV
Shutdown VIN Current
Operating VIN Current
1.5
0.5
0.8
0.8
3
µA
mA
V
EN=0V, VIN=12V
1
VFB=1.2V and after fault
0.792
0.784
0.808
0.816
Reference Voltage
V
•
•
VSC_TH, Feedback pin Short
Circuit Latch Threshold
0.50
0.55
0.65
V
TON, Switch On-Time
TON, Switch On-Time
TOFF_MIN, Minimum Off-Time
Soft Start Time
0.4
0.4
0.5
0.5
250
2
0.6
0.6
350
µs
µs
ns
ms
V
•
•
•
VIN=12V, XRP6124
VIN=24V, XRP6124HV
VIN=12V
EN Turn-On Threshold
EN Turn-Off Threshold
EN Bias Current
2
1
V
0.01
6
0.1
µA
Gate Driver Pull-Down
Resistance
9
8
Ω
Gate Driver Pull-up Resistance
tr, gate rise time
5
Ω
ns
ns
V
45
35
6.4
CGATE=1nF
CGATE=1nF
VIN=12V
VIN=3.0V
tf, gate fall time
VIN - GATE voltage difference
VIN - GATE voltage difference
5.5
2.6
8
•
•
V
© 2011 Exar Corporation
2/12
Rev. 1.1.0
XRP6124
Non-Synchronous PFET Step-Down Controller
BLOCK DIAGRAM
Figure 2: XRP6124 Block Diagram
PIN ASSIGNMENT
E N
GND
FB
VIN
1
2
3
5
4
XRP6124
GATE
Figure 3: XRP6124 Pin Assignment
PIN DESCRIPTION
Name
Pin Number
Description
EN
GND
FB
1
2
3
Enable Pin. Actively pull high to enable the part.
Ground
Feedback pin
Gate Pin. Connect to gate of PFET. This pin pulls the gate of the PFET approximately
6V below Vin in order to turn on the FET. For 6V>VIN>3V the gate pulls to within 0.4V
of ground. Therefore a PFET with a gate rating of 2.6V or lower should be used.
GATE
VIN
4
5
Input Voltage
ORDERING INFORMATION
Temperature
Packing
Quantity
Part Number
Range
Marking
Package
Note 1
Note 2
XRP6124ES0.5-F
XRP6124ESTR0.5-F
XRP6124HVES0.5-F
XRP6124HVESTR0.5-F
XRP6124EVB
-40°C≤TJ≤125°C
-40°C≤TJ≤125°C
-40°C≤TJ≤125°C
-40°C≤TJ≤125°C
5-pin SOT23
Bulk
Halogen Free
0.5µs/18V max
0.5µs/18V max
0.5µs/30V max
0.5µs/30V max
5-pin SOT23 2.5K/Tape & Reel Halogen Free
5-pin SOT23 Bulk Halogen Free
5-pin SOT23 2.5K/Tape & Reel Halogen Free
XRP6124 Evaluation Board
“YY” = Year – “WW” = Work Week – “X” = Lot Number
© 2011 Exar Corporation
3/12
Rev. 1.1.0
XRP6124
Non-Synchronous PFET Step-Down Controller
TYPICAL PERFORMANCE CHARACTERISTICS
All data taken at TJ = TA = 25°C, unless otherwise specified – Curves are based on Schematic and BOM from Application
Information section of this datasheet. Refer to figure 20 for XRP6124 and to figure 21 for XRP6124HV.
Fig. 4: Efficiency versus IOUT, VIN=12V
Fig. 5: Efficiency versus IOUT, VIN=24V
Fig. 7: TON versus VIN
Fig. 6: TON versus VIN
Fig. 8: Load Regulation
Fig. 9: Load Regulation
© 2011 Exar Corporation
4/12
Rev. 1.1.0
XRP6124
Non-Synchronous PFET Step-Down Controller
XRP6124ES0.5-F
Fig. 10: Line Regulation
Fig. 11: Line Regulation
XRP6124ES0.5-F
XRP6124HVES0.5-F
VOUT
VOUT
AC coupled
10mV/div
AC coupled
20mV/div
LX
20V/div
LX
10V/div
IL
IL
2A/div
2A/div
2µs/div
1µs/div
Fig. 13: Steady state, VIN=24V, VOUT=5.0V, IOUT=3A
Fig. 12: Steady state, VIN=12V, VOUT=3.3V, IOUT=3A
XRP6124ES0.5-F
XRP6124HVES0.5-F
90mV
180mV
VOUT
AC coupled
100mV/div
VOUT
AC coupled
200mV/div
IOUT
1A/div
IOUT
1A/div
10µs/div
20µs/div
Fig. 14: Load step transient response, 1.4A-3A-1.4A
Fig. 15: Load step transient response, 1.4A-3A-1.4A
© 2011 Exar Corporation
5/12
Rev. 1.1.0
XRP6124
Non-Synchronous PFET Step-Down Controller
XRP6124ES0.5-F
XRP6124HVES0.5-F
180mV
90mV
VOUT
AC coupled
100mV/div
VOUT
AC coupled
200mV/div
IOUT
1A/div
IOUT
1A/div
50µs/div
50µs/div
Fig. 16: Load step transient response corresponding to a
CCM-DCM transition, 0.05A-1.6A-0.05A
Fig. 17: Load step transient response corresponding to a
CCM-DCM transition, 0.05A-1.6A-0.05A
Fig. 18: Shutdown current versus VIN, VEN=0V
Fig. 19: Shutdown current versus VIN, VEN=0V
© 2011 Exar Corporation
6/12
Rev. 1.1.0
XRP6124
Non-Synchronous PFET Step-Down Controller
THEORY OF OPERATION
VOUT
fs =
VIN ×TON
THEORY OF OPERATION
Since for each voltage option, the product of
The XRP6124 utilizes a proprietary Constant
On-Time (COT) control with emulated ESR.
The on-time is internally set and automatically
adjusts during operation, inversely with the
voltage VIN, in order to maintain a constant
frequency. Therefore the switching frequency
is independent of the inductor and capacitor
VIN and TON is the constant K shown in table 1,
then switching frequency is determined by
VOUT as shown in table 2.
Switching frequency fs(kHz)
VOUT
size,
unlike
hysteretic
controllers.
The
XRP6124ES0.5-F
XRP6124HVES0.5-F
emulated ESR ramp allows the use of ceramic
capacitors for output filtering.
1.2
1.5
1.8
2.5
3.3
5.0
12
200
250
300
417
550
833
---
100
125
150
208
275
417
1000
At the beginning of each cycle, the XRP6124
turns on the P-Channel FET for a fixed
duration. The on-time is internally set and
adjusted by VIN. At the end of the on-time the
FET is turned off, for a predetermined
minimum off time TOFF-MIN (nominally 250ns).
After the TOFF-MIN has expired the voltage at
feedback pin FB is compared to a voltage
ramp at the feedback comparators positive
input. Once VFB drops below the ramp voltage,
the FET is turned on and a new cycle starts.
This voltage ramp constitutes an emulated
ESR and makes possible the use of ceramic
capacitors, in addition to other capacitors, as
output filter for the buck converter.
Table 2: Switching frequency fs
for the XRP6124 voltage options
Where it is advantageous, the high-voltage
option may be used for low-voltage
applications. For example a 12VIN to 5VOUT
conversion using a low-voltage option will
result in switching frequency of 833kHz as
shown in table 2. If it is desired to increase
the converter efficiency, then switching losses
can be reduced in half by using a high-voltage
option operating at a switching frequency of
417kHz.
VOLTAGE OPTIONS
The XRP6124 is available in two voltage
options as shown in table 1. The low-voltage
and high-voltage options have TON of 0.5µs at
12VIN and 24VIN respectively. Note that TON is
inversely proportional to VIN. The constant of
proportionality K, for each voltage option is
shown in table 1. Variation of TON versus VIN is
shown graphically in figures 6 and 7.
Maximum Output Current IOUT(A)
VOUT
XRP6124ES0.5-F
XRP6124HVES0.5-F
3.3VIN
5.0VIN
12VIN
18VIN
24VIN
---
---
4
1.2
1.5
1.8
2.5
3.3
5.0
12
5
5
5
5
4
4
---
4
5
5
4
4
4
4
4
4
4
---
---
---
4
3
4
4
Voltage
Part Number
TON (µs)
K=TONxVIN
---
---
3
3
3
rating (V)
(μs.V)
---
2
2
3-18
XRP6124ES0.5-F 0.5 @ 12VIN
XRP6124HVES0.5-F 0.5 @ 24VIN
6
Table 3: Maximum recommended IOUT
4.5-30
12
SHORT-CIRCUIT PROTECTION
Table 1 : XRP6124 voltage options
The purpose of this feature is to prevent an
accidental short-circuit at the output from
damaging the converter. The XRP6124 has a
For a buck converter the switching frequency
fs can be expressed in terms of VIN, VOUT and
TON as follows:
short-circuit
comparator
that
constantly
monitors the feedback node, after soft-start is
© 2011 Exar Corporation
7/12 Rev. 1.1.0
XRP6124
Non-Synchronous PFET Step-Down Controller
finished. If the feedback voltage drops below
XRP6124 will latch up. In applications where
an independent enable signal is not available,
a Zener diode can be used to derive VEN from
VIN.
0.55V, equivalent to output voltage dropping
below 69% of nominal, the comparator will
trip causing the IC to latch off. In order to
restart the XRP6124, the input voltage has to
be reduced below UVLO threshold and then
increased to its normal operating point.
DISCONTINUOUS CONDUCTION MODE, DCM
Because XRP6124 is
a
non-synchronous
controller, when load current IOUT is reduced to
less than half of peak-to-peak inductor current
ripple ΔIL, the converter enters DCM mode of
operation. The switching frequency fs is now
IOUT dependent and no longer governed by the
relationship shown in table 2. As IOUT is
decreased so does fs until a minimum
switching frequency, typically in the range of
few hundred Hertz, is reached at no load. This
contributes to good converter efficiency at
light load as seen in figures 4 and 5. The
reduced fs corresponding to light load,
however, increases the output voltage ripple
and causes a slight increase in output voltage
as seen in figures 8 and 9. Another effect of
reduced fs at light load is slow down of
SOFT-START
To limit in-rush current the XRP6124 has an
internal soft-start. The nominal soft-start time
is 2ms and commences when VIN exceeds the
UVLO threshold. As explained above, the
short-circuit comparator is enabled as soon as
soft-start is complete. Therefore if the input
voltage has a very slow rising edge such that
at the end of soft-start the output voltage has
not reached 69% of its final value then the
XRP6124 will latch-off.
ENABLE
By applying a logic-level signal to the enable
pin EN the XRP6124 can be turned on and off.
Pulling the enable below 1V shuts down the
controller and reduces the VIN leakage current
to 1.5µA nominal as seen in figure 18. Enable
signal should always be applied after the input
voltage or concurrent with it. Otherwise
transient response when
a
load step
transitions from a high load to a light load.
This is shown in figures 16 and 17.
APPLICATION INFORMATION
SETTING THE OUTPUT VOLTAGE
FEED-FORWARD CAPACITOR CFF
Use an external resistor divider to set the
output voltage. Program the output voltage
from:
CFF, which is placed in parallel with R1,
provides
a
low-impedance/high-frequency
path for the output voltage ripple to be
transmitted to FB. It also helps get an
optimum transient response. An initial value
for CFF can be calculated from:
V
⎛
⎜
⎞
⎟
OUT
R1 = R2×
−1
0.8
⎝
⎠
1
CFF =
where:
2×π × fs ×0.1× R1
R1 is the resistor between VOUT and FB
where:
R2 is the resistor between FB and GND
(nominally 2kΩ)
fs is the switching frequency from table 2
0.8V is the nominal feedback voltage.
This value can be adjusted as necessary to
provide an optimum load step transient
response.
© 2011 Exar Corporation
8/12
Rev. 1.1.0
XRP6124
Non-Synchronous PFET Step-Down Controller
ESR of the capacitor has to be selected such
that the output voltage ripple requirement
OUTPUT INDUCTOR
Select the output inductor L1 for inductance L,
DC current rating IDC and saturation current
rating ISAT. IDC should be larger than regulator
output current. ISAT, as a rule of thumb, should
be 50% higher than the regulator output
current. Calculate the inductance from:
VOUT(ripple), nominally 1% of VOUT, is met.
Voltage ripple VOUT(ripple) is composed mainly of
two components: the resistive ripple due to
ESR and capacitive ripple due to COUT charge
transfer. For applications requiring low voltage
ripple, ceramic capacitors are recommended
because of their low ESR which is typically in
the range of 5mΩ. Therefore VOUT(ripple) is
mainly capacitive. For ceramic capacitors
calculate the VOUT(ripple) from:
⎛
⎞
VOUT
⎜
⎟
⎟
L =
(
VIN −VOUT
)
⎜
ΔIL × fs×VIN
⎝
⎠
Where:
ΔIL
8×COUT × fs
ΔIL is peak-to-peak inductor current ripple
nominally set to 30% of IOUT
VOUT(ripple)
=
fS is nominal switching frequency from table 2
Where:
COUT is the value calculated above
OUTPUT CAPACITOR COUT
If tantalum or electrolytic capacitors are used
then VOUT(ripple) is essentially a function of ESR:
Select the output capacitor for voltage rating,
capacitance COUT and Equivalent Series
Resistance ESR. The voltage rating, as a rule
of thumb, should be twice the output voltage.
When calculating the required capacitance,
usually the overriding requirement is current
load-step transient. If the unloading transient
requirement (i.e., when IOUT transitions from a
high to a low current) is met, then usually the
loading transient requirement (when IOUT
transitions from a low to a high current) is met
as well. Therefore calculate the COUT
capacitance based on the unloading transient
requirement from:
VOUT(ripple) = ΔIL × ESR
INPUT CAPACITOR CIN
Select the input capacitor for voltage rating,
RMS current rating and capacitance. The
voltage rating, as a rule of thumb, should be
50% higher than the regulator’s maximum
input voltage. Calculate the capacitor’s current
rating from:
ICIN,RMS = IOUT × D×
(
1− D
)
2
IHigh2 − ILOW
⎛
⎜
⎞
⎟
COUT = L×
2
(
VOUT +Vtransient
2 −VOUT
)
⎜
⎝
⎟
⎠
Where:
IOUT is regulator’s maximum current
D is duty cycle (D=VOUT/VIN)
Where:
L is the inductance calculated in the preceding
step
Calculate the CIN capacitance from:
IHigh is the value of IOUT prior to unloading. This
is nominally set equal to regulator current
rating.
IOUT ×VOUT
×
(
VIN −VOUT
)
CIN =
fs×VIN 2 ×ΔVIN
ILow is the value of IOUT after unloading. This is
nominally set equal to 50% of regulator
current rating.
Where:
ΔVIN is the permissible input voltage ripple,
nominally set to 1% of VIN.
Vtransient is the maximum permissible voltage
transient corresponding to the load step
mentioned above. Vtransient is typically specified
from 3% to 5% of VOUT
.
© 2011 Exar Corporation
9/12
Rev. 1.1.0
XRP6124
Non-Synchronous PFET Step-Down Controller
TYPICAL APPLICATIONS
12V TO 3.3V / 3A CONVERSION
VIN 6V to 18V
1
5
EN
VIN
XRP6124ES
CIN, X5R
22uF, 25V
2
3
GND
FB
M1
IRF9335
4
GATE
L1, 4.7uH
DR74-4R7-R
VOUT 3.3V/3A
D1
MBRA340
CFF
1nF
C
OUT, X5R
R1, 1%
6.34k
2x22uF, 10V
R2, 1%
2k
Fig. 20: 12V to 3.3V/3A regulator
24V TO 5V / 3A CONVERSION
VIN 8V to 30V
1
5
EN
VIN
XRP6124HVES
CIN, X5R
10uF, 50V
2
3
GND
M1
DMP4050SSS
4
FB
GATE
L1, 8.2uH
HCM0730
VOUT 5.0V/3A
D1
MBRA340
CFF
0.47nF
COUT, X5R
2x22uF, 16V
R1, 1%
10.5k
R2, 1%
2k
Fig. 21: 24V to 5V/3A regulator
© 2011 Exar Corporation
10/12
Rev. 1.1.0
XRP6124
Non-Synchronous PFET Step-Down Controller
PACKAGE SPECIFICATION
5-PIN SOT23
© 2011 Exar Corporation
11/12
Rev. 1.1.0
XRP6124
Non-Synchronous PFET Step-Down Controller
REVISION HISTORY
Revision
Date
Description
1.0.0
1.1.0
01/26/2011
01/31/2011
Initial release of datasheet
Corrected typo (changed V to I) on formula under Input Capacitor CIN paragraph
FOR FURTHER ASSISTANCE
Email:
customersupport@exar.com
Exar Technical Documentation:
http://www.exar.com/TechDoc/default.aspx?
EXAR CORPORATION
HEADQUARTERS AND SALES OFFICES
48720 Kato Road
Fremont, CA 94538 – USA
Tel.: +1 (510) 668-7000
Fax: +1 (510) 668-7030
www.exar.com
NOTICE
EXAR Corporation reserves the right to make changes to the products contained in this publication in order to improve
design, performance or reliability. EXAR Corporation assumes no responsibility for the use of any circuits described herein,
conveys no license under any patent or other right, and makes no representation that the circuits are free of patent
infringement. Charts and schedules contained here in are only for illustration purposes and may vary depending upon a
user’s specific application. While the information in this publication has been carefully checked; no responsibility, however,
is assumed for inaccuracies.
EXAR Corporation does not recommend the use of any of its products in life support applications where the failure or
malfunction of the product can reasonably be expected to cause failure of the life support system or to significantly affect its
safety or effectiveness. Products are not authorized for use in such applications unless EXAR Corporation receives, in
writing, assurances to its satisfaction that: (a) the risk of injury or damage has been minimized; (b) the user assumes all
such risks; (c) potential liability of EXAR Corporation is adequately protected under the circumstances.
Reproduction, in part or whole, without the prior written consent of EXAR Corporation is prohibited.
© 2011 Exar Corporation
12/12
Rev. 1.1.0
相关型号:
©2020 ICPDF网 联系我们和版权申明