SP706CN-L [EXAR]
暂无描述;SP705-708/813L
Low Power Microprocessor Supervisory Circuits
■ Precision Voltage Monitor:
SP705/707/813L at 4.65V
SP706/708 at 4.40V
■ RESET Pulse Width - 200ms
■ Independent Watchdog Timer - 1.6s
Timeout (SP705/706/813L)
■ 60µA Maximum Supply Current
■ Debounced TTL/CMOS Manual Reset Input
■ RESET Asserted Down to VCC = 1.1V
■ Voltage Monitor for Power Failure or Low
Battery Warning
■ Available in 8-pin PDIP, NSOIC, and
µSOIC packages
Now available in Lead Free
■ Pin Compatible Enhancement to Industry Standard 705-708/813L Series
■ Functionally Compatible to Industry Standard 1232 Series
DESCRIPTION…
The SP705-708/813L series is a family of microprocessor (µP) supervisory circuits that
integrate myriad components involved in discrete solutions which monitor power-supply and
battery in µP and digital systems. The SP705-708/813L series will significantly improve
system reliability and operational efficiency when compared to solutions obtained with discrete
components. The features of the SP705-708/813L series include a watchdog timer,
a µP reset, a Power Fail Comparator, and a manual-reset input. The SP705-708/813L
series is ideal for applications in automotive systems, computers, controllers, and intelligent
instruments. The SP705-708/813L series is an ideal solution for systems in which critical
monitoring of the power supply to the µP and related digital components is demanded.
Part
Number
RESET
Threshold
RESET
Active
Manual
RESET
PFI
Accuracy
Watchdog
SP705
SP706
SP707
SP708
SP813L
4.65 V
4.40 V
4.65 V
4.40 V
4.65 V
LOW
LOW
YES
YES
YES
YES
YES
YES
YES
NO
4%
4%
4%
4%
4%
LOW and HIGH
LOW and HIGH
HIGH
NO
YES
June 2008 Rev C
SP705 Low Power Microprocessor Supervisory Circuits
© 2008 Exar Corporation
1
Continuous Power Dissipation
ABSOLUTE MAXIMUM RATINGS
Plastic DIP (derate 9.09mW/°C above +70°C)727mW
SO (derate 5.88mW/°C above +70°C) ...... 471mW
Mini SO (derate 4.10mW/°C above +70°C) 330mW
This is a stress rating only and functional operation
of the device at these or any other conditions above
those indicated in the operation sections of this
specification is not implied. Exposure to absolute
maximum rating conditions for extended periods of
time may affect reliability and cause permanent
damage to the device.
Storage Temperature Range ....... -65°C to +160°C
Lead Temperature (soldering, 10s) ............ +300°C
Vcc ....................................................................................... -0.3V to +6.0V
All Other Inputs (Note 1) ......... -0.3V to (Vcc+0.3V)
Input Current:
Vcc ............................................................................................................. 20mA
GND ............................................................ 20mA
Output Current (all outputs) ......................... 20mA
ESD Rating..................................................... 4KV
SPECIFICATIONS
VCC = 4.75V to 5.50V for SP705/707/813L, VCC = 4.50V to 5.50V for SP706/708, TA = TMIN to TMAX, unless otherwise noted, typical at 25oC.
PARAMETER
MIN.
TYP. MAX.
UNITS
CONDITIONS
Operating Voltage Range, VCC
5.5
V
1.1
Supply Current, ISUPPLY
Reset Threshold
40
60
µA
MR=VCC or Floating, WDI Floating
4.50
4.25
4.65
4.40
4.75
4.50
V
SP705, SP707, SP813L, Note 2
SP706, SP708, Note 2
Reset Threshold Hysteresis
Reset Pulse Width, tRS
40
mV
ms
Note 2
Note 2
Note 2
140
200
280
RESET Output Voltage
V
CC-1.5
0.8
I
SOURCE = 800µA
V
ISOURCE=4µA, VCC=1.1V
0.40
0.30
I
SINK = 3.2mA
Vcc = 1.1V, ISINK = 50
SP705, SP706, SP813L
VIL = 0.4V, VIH = 0.8XVCC
SP705, SP706, SP813L
CC = 5V
µA
Watchdog Timeout Period, tWD
WDI Pulse Width, tWP
1.00
1
1.60
2.25
s
µs
WDI Input Threshold,
LOW
HIGH
0.8
75
V
V
3.5
-75
WDI Input Current
30
µA
SP705, SP706, SP813L
WDI = VCC
SP705, SP706, SP813L
WDI = 0V
-20
June 2008 Rev C
SP705 Low Power Microprocessor Supervisory Circuits
© 2008 Exar Corporation
2
SPECIFICATIONS
VCC = 4.75V to 5.50V for SP705/707/813L,813M, VCC = 4.50V to 5.50V for SP706/708, TA = TMIN to TMAX, unless otherwise noted, typical at 25oC.
PARAMETER
MIN.
TYP. MAX.
UNITS
CONDITIONS
WDO Output Voltage
VCC-1.5
ISOURCE=800µA
ISINK=3.2mA
V
0.40
MR Pull-Up Current
MR Pulse Width, tMR
100
150
250
600
0.8
µA
MR = 0V
ns
MR Input Threshold
LOW
HIGH
V
2.0
MR to Reset Out Delay, tMD
PFI Input Threshold
PFI Input Current
250
ns
V
Note 2
CC = 5V
1.20
1.25
1.30
V
-25.00
0.01 25.00
nA
V
PFO Output Voltage
VCC-1.5
ISOURCE = 800µA
SINK = 3.2mA
0.4
I
Note 1: The input voltage limits on PFI and MR can be exceeded if the input current is less than 10mA.
Note 2: Applies to both RESET in the SP705-SP708 and RESET in the SP707/708/813L/813M.
DIP and SOIC
µSOIC
1
1
2
8
7
8
7
MR
RESET / RESET*
WDO
WDO
WDI
PFO
2
3
4
V
CC
RESET / RESET*
SP705
SP706
SP813L
SP705
SP706
SP813L
3
4
6
5
6
5
GND
PFI
MR
WDI
PFO
PFI
V
CC
GND
1
2
1
2
8
7
8
7
RESET
RESET
MR
N.C.
PFO
RESET
RESET
V
CC
SP707
SP708
SP707
SP708
3
4
6
5
3
4
6
5
MR
GND
PFI
PFI
N.C.
PFO
V
CC
GND
* SP813L only
* SP813L only
Figure 1. Pinouts
June 2008 Rev C
SP705 Low Power Microprocessor Supervisory Circuits
© 2008 Exar Corporation
3
PIN DESCRIPTION
SP705/706
SP707/708
SP813L
NAME
FUNCTION
DIP/
DIP/
SOIC
DIP/
SOIC
µSOIC
SOIC
µSOIC
µSOIC
Manual Reset - This input triggers a reset pulse
when pulled below 0.8V. This active-LOW input
has an internal 250µA pull-up current. It can be
driven from a TTL or CMOS logic line or shorted
to ground with a switch
MR
1
3
1
3
1
3
VCC
+5V power supply
2
3
4
5
2
3
4
5
2
3
4
5
GND
Ground reference for all signals
Power-Fail Input - When this voltage monitor input
is less than 1.25V, PFO goes LOW. Connect PFI
to ground or VCC when not in use.
PFI
4
5
6
7
4
5
6
7
4
5
6
7
Power-Fail Output - This output is HIGH until PFI
is less than 1.25V.
PFO
Watchdog Input - If this input remains HIGH or
LOW for 1.6s, the internal watchdog timer times
out and WDO goes LOW. Floating WDI or
connecting WDI to a high-impedance tri-state
buffer disables the watchdog feature. The internal
watchdog timer clears whenever RESET is
asserted, WDI is tri-stated, or whenever WDI sees
a rising or falling edge.
WDI
N.C.
6
-
8
-
-
-
6
-
8
-
No Connect.
6
7
8
1
Active-LOW RESET Output - This output pulses
LOW for 200ms when triggered and stays LOW
whenever VCC is below the reset threshold (4.65V
for the SP705/707/813L and 4.40V for the
SP706/708). It remains LOW for 200ms after Vcc
rises above the reset threshold or MR goes from
LOW to HIGH. A watchdog timeout will not trigger
RESET unless WDO is connected to MR.
RESET
7
1
-
-
Watchdog Output - This output pulls LOW when
the internal watchdog timer finishes its 1.6s count
and does not go HIGH again until the watchdog is
cleared. WDO also goes LOW during low-line
conditions. Whenever VCC is below the reset
threshold, WDO stays LOW. However, unlike
RESET, WDO does not have a minimum pulse
width. As soon as VCC is above the reset
WDO
8
2
-
-
8
7
2
1
threshold, WDO goes HIGH with no delay.
Active-HIGH RESET Output - This output is the
complement of RESET. Whenever RESET is
HIGH, RESET is LOW, and vice versa. Note the
SP813L/813M has a reset output only.
RESET
-
-
8
2
Table 1. Device Pin Description
June 2008 Rev C
SP705 Low Power Microprocessor Supervisory Circuits
© 2008 Exar Corporation
4
WATCHDOG
TRANSITION
DETECTOR
WATCHDOG
TIMER
WDI
MR
WDO
V
CC
TIMEBASE FOR
RESET AND
WATCHDOG
250µA
RESET
GENERATOR
RESET/RESET*
V
CC
4.65V
(4.40V for the SP706 and SP813M)
PFI
PFO
SP705
SP706
SP813L
1.25V
GND
* For the SP813L only
Figure 2. Internal Block Diagram for the SP705/706/813L
V
CC
RESET
RESET
250µA
MR
RESET
GENERATOR
V
CC
4.65V
(4.40V for the SP708)
PFI
PFO
1.25V
SP707
SP708
GND
Figure 3. Internal Block Diagram for the SP707/708
June 2008 Rev C
SP705 Low Power Microprocessor Supervisory Circuits
© 2008 Exar Corporation
5
+5V
V
CC = +5V
T
A
= +25 C
PFI
PFO
1KΩ
30pF
+1.25V
Figure 4A. Power-Fail Comparator De-assertion
Response Time.
Figure 4B. Circuit for the Power-Fail Comparator De-
assertion Response Time.
+5V
V
CC = +5V
T
A
= +25 C
1KΩ
PFI
PFO
30pF
+1.25V
Figure 5A. Power-Fail Comparator Assertion Response
Time.
Figure 5B. Circuit for the Power-Fail Comparator
Assertion Response Time.
V
CC
T
A
= +25oC
RESET
V
CC
2KΩ
RESET
330pF
GND
Figure 6A. SP705/707 RESET Output Voltage vs.
Supply Voltage.
Figure 6B. Circuit for the SP705/707 RESET Output
Voltage vs. Supply Voltage.
June 2008 Rev C
SP705 Low Power Microprocessor Supervisory Circuits
© 2008 Exar Corporation
6
V
CC
T
A
= +25oC
RESET
V
CC
10KΩ
RESET
330pF
GND
Figure 7A. SP705/707 RESET Response Time
Figure 7B. Circuit for the SP705/707 RESET Response
Time
Figure 8. SP707 RESET and RESET Assertion
Figure 9. SP707 RESET and RESET De-Assertion
V
CC
T
A
= +25oC
RESET
V
CC
10KΩ
330pF
330pF
RESET
10KΩ
GND
Figure 10. Circuit for the SP707 RESET and RESET Assertion and De-Assertion
June 2008 Rev C
SP705 Low Power Microprocessor Supervisory Circuits
© 2008 Exar Corporation
7
Figure 11. SP707/708/813L RESET Output
Voltage vs. Supply Voltage
Figure 12. SP813L RESET Response Time
V
CC
V
CC
RESET
330pF
10KΩ
GND
Figure 13. Circuit for the SP707/708/813L RESET Output Voltage vs. Supply Voltage and the SP813L
RESET Response Time
June 2008 Rev C
SP705 Low Power Microprocessor Supervisory Circuits
© 2008 Exar Corporation
8
FEATURES
RESET Output
The SP705-708/813L series provides four
key functions:
1. A reset output during power-up, power-down
and brownout conditions.
2. An independent watchdog output that goes
LOW if the watchdog input has not been toggled
within 1.6 seconds.
3. A 1.25V threshold detector for power-fail
warning, low battery detection, or monitoring a
power supply other than +5V.
A microprocessor's reset input starts the µP
in a known state. The SP705-708/813L
series asserts reset during power-up and
prevents code execution errors during power-
down or brownout conditions.
On power-up, once VCC reaches 1.1V, RESET
is aguaranteedlogicLOWof0.4Vorless. AsVCC
rises, RESET stays LOW. When VCC rises
above the reset threshold, an internal timer re-
leases RESET after 200ms. RESET pulses
LOWwheneverVCC dipsbelowtheresetthresh-
old, such as in a brownout condition. When a
brownout condition occurs in the middle of a
previously initiated reset pulse, the pulse con-
tinues for at least another 140ms. On power-
down, once VCC falls below the reset threshold,
RESETstaysLOWandisguaranteedtobe0.4V
or less until VCC drops below 1.1V.
4. An active-LOW manual-reset that allows
RESET to be triggered by a pushbutton switch.
The SP707/708 devices are the same as the
SP705/706 devices except for the active-HIGH
RESET substitution of the watchdog timer. The
SP813L is the same as the SP705 except an
active-HIGH RESET is provided rather than an
active-LOW RESET. The SP705/707/813L
devices generate a reset when the supply voltage
drops below 4.65V. The SP706/708
The SP707/708/813L active-HIGH
devices generate a reset below 4.40V.
RESET output is simply the complement of the
RESEToutputandisguaranteedtobevalidwith
VCC down to 1.1V. Some µPs, such as Intel's
80C51, require an active-HIGH reset pulse.
The SP705-708/813L series is ideally
suited for applications in automotive systems,
intelligent instruments, and battery-powered
computersandcontrollers.TheSP705-708/813L
series is ideally applied in environments
wheremonitoringofpowersupplytoaµPandits
related components is critical.
Watchdog Timer
The SP705/706/813L watchdog circuit
monitors the µP's activity. If the µP does not
toggle the watchdog input (WDI) within 1.6
seconds and WDI is not tri-stated, WDO goes
LOW. AslongasRESETisassertedortheWDI
input is tri-stated, the watchdog timer will stay
cleared and will not count. As soon as RESET
is released and WDI is driven HIGH or LOW,
the timer will start counting. Pulses as short as
50ns can be detected.
THEORY OF OPERATION
The SP705-708/813L series is a
microprocessor (µP) supervisory circuit that
monitors the power supplied to digital circuits
such as microprocessors, microcontrollers, or
memory. The series is an ideal solution for
portable, battery-powered equipment that
requirespowersupplymonitoring.Implementing
thisserieswillreducethenumberofcomponents
andoverallcomplexity. Thewatchdogfunctions
of this product family will continuously oversee
theoperationalstatusofasystem. Theoperational
features and benefits of the SP705-708/813L
series are described in more detail below.
June 2008 Rev C
SP705 Low Power Microprocessor Supervisory Circuits
© 2008 Exar Corporation
9
t
WP
t
WD
t
WD
+5V
0V
WDI
+5V
0V
WDO
t
WD
+5V
0V
RESET*
RESET*
t
RS
+5V
0V
* externally triggered LOW by MR,
RESET is for the SP813L only
Figure 14. SP705/706/813L Watchdog Timing Waveforms
Typically, WDO will be connected to the
non-maskable interrupt input (NMI) of a µP.
When VCC drops below the reset threshold,
WDO will go LOW whether or not the watch-
dog timer has timed out. Normally this would
trigger an NMI but RESET goes LOW simulta-
neously, and thus overrides the NMI.
If WDI is left unconnected, WDO can be used as
a low-line output. Since floating WDI disables
the internal timer, WDO goes LOW only when
VCC falls below the reset threshold, thus func-
tioning as a low-line output.
+5V
V
RT
V
RT
V
CC
0V
+5V
0V
WDO
t
RS
t
RS
+5V
0V
RESET
MR*
+5V
0V
tMD
*externally driven LOW
t
MR
Figure 15. SP705/706 Timing Diagrams with WDI Tri-stated. The SP707/708/813L RESET Output is the Inverse
of the RESET Waveform Shown.
June 2008 Rev C
SP705 Low Power Microprocessor Supervisory Circuits
© 2008 Exar Corporation
10
Ensuring a Valid RESET Output Down to
VCC = 0V
Power-Fail Comparator
The power-fail comparator can be used for
various purposes because its output and
noninverting input are not internally connected.
The inverting input is internally connected to a
1.25V reference.
When VCC falls below 1.1V, the SP705/706/707/
708 RESET output no longer sinks current, it
becomes an open circuit. High-impedance
CMOS logic inputs can drift to undetermined
voltages if left undriven. If a pull-down resistor
is added to the RESET pin, any stray charge or
leakage currents will be shunted to ground,
holding RESET LOW. The resistor value is not
critical. Itshouldbeabout100KΩ,largeenough
not to load RESET and small enough to pull
RESET to ground.
To build an early-warning circuit for power
failure, connect the PFI pin to a voltage divider
as shown in Figure 16. Choose the voltage
divider ratio so that the voltage at PFI falls
below1.25Vjustbeforethe+5Vregulatordrops
out. Use PFO to interrupt the µP so it can
prepare for an orderly power-down.
Monitoring Voltages Other Than the
Unregulated DC Input
Manual Reset
The manual-reset input (MR) allows RESET to
be triggered by a pushbutton switch. The switch
is effectively debounced by the 140ms mini-
mum RESET pulse width. MR is TTL/CMOS
logic compatible, so it can be driven by an
external logic line. MR can be used to force a
watchdog timeout to generate a RESET pulse
in the SP705/706/813L. Simply connect
WDO to MR.
MonitorvoltagesotherthantheunregulatedDC
by connecting a voltage divider to PFI and
adjusting the ratio appropriately. If required,
add hysteresis by connecting a resistor (with a
value approximately 10 times the sum of the
two resistors in the potential divider network)
betweenPFIandPFO. AcapacitorbetweenPFI
and GND will reduce the power-fail circuit's
Regulated +5V
Power Supply
+12V
+5V
V
Unregulated DC
Power Supply
0.1µF
VCC
1MΩ
1%
CC
MR
VCC
R
1
2
PFI
RESET
RESET
µP
PFI
MR
INTERRUPT
PFO
PFI
PFO
130KΩ
1%
I/O LINE
NMI
R
SP705
SP706
SP813L
WDO
RESET
to µP
GND
GND
GND
PUSHBUTTON
SWITCH
Figure 16. Typical Operating Circuit
Figure 17. Monitoring Both +5V and +12V Power
Supplies
June 2008 Rev C
SP705 Low Power Microprocessor Supervisory Circuits
© 2008 Exar Corporation
11
sensitivity to high-frequency noise on the
line being monitored. RESET can be used to
monitor voltages other than the +5V VCC
line. Connect PFO to MR to initiate a RESET
pulse when PFI drops below 1.25V. Figure 17
shows the SP705/706/707/708 configured to
assert RESET when the +5V supply falls below
the RESET threshold, or when the +12V supply
falls below approximately 11V.
Interfacing to mPs with Bidirectional
RESET Pins
µPs with bidirectional RESET pins, such as the
Motorola 68HC11 series, can contend with the
SP705/706/707/708 RESET output. If, for
example, the RESET output is driven HIGH and
the µP wants to pull it LOW, indeterminate
logic levels may result. To correct this, connect
a4.7KΩresistorbetweentheRESEToutputand
the µP reset I/O, as shown if Figure 19. Buffer
the RESET output to other system components.
Monitoring a Negative Voltage Supply
The power-fail comparator can also monitor a
negative supply rail, shown in Figure 18. When
the negative rail is good (a negative voltage of
large magnitude), PFO is LOW. By adding the
resistors and transistor as shown, a HIGH PFO
triggersRESET. AslongasPFOremainsHIGH,
the SP705-708/813L will keep RESET
asserted (where RESET = LOW and RESET =
HIGH). Note that this circuit's accuracy de-
pends on the PFI threshold tolerance, the VCC
line, and the resistors.
+5V
VCC
R
1
100KΩ
MR
PFI
Buffered RESET connects to System Components
PFO
2N3904
100KΩ
R2
RESET
to µP
+5V
V
+5V
V
V-
GND
CC
CC
5.0 - 1.25
1.25 - VTRIP
R
R
1
2
=
, VTRIP < 0
µP
RESET
RESET
4.7KΩ
+5V
MR
0V
+5V
0V
V-
V-
GND
GND
PFO
VTRIP
0V
Figure 18. Monitoring a Negative Voltage Supply
Figure 19. Interfacing to Microprocessors with
Bidirectional RESET I/O for the SP705/706/707/708
OCT 17-06 RevB
SP705 Low Power Microprocessor Supervisory Circuits
© 2008 Exar Corporation
12
45
44
43
42
41
40
39
38
37
36
35
45
44
43
42
41
40
39
38
37
36
35
4.75V
5.0V
5.5V
-40C
25C
+85C
-40C
25C
+85C
4.75V
5.0V
5.5V
Centigrade Temperature
VCC
Figure 20. Supply Current vs. Temperature
Figure 21. Supply Current vs. Supply Voltage
UnliketheDS1232,theSP705-708/813L
Applications
series has a separate watchdog output pin WDO
which can be simply connected to the MR input
to generate a Reset signal. The DS1232 has pin
selectable features, while the SP705-708/813L
series has more fixed functions of reset
threshold and watchdog time-out delay. For
most applications, the fixed functions will be
preferred, with the benefit of reduced cost due to
a less complex part. In addition, the SP705-708/
813L series has a power fail input and
output function not available with the DS1232
that is useful for monitoring systems with
unregulated supply voltages. The SP705-708/
813L series is available in one of the
industry's smallest space-saving package sizes,
the µSOIC.
The SP705-708/813L series offers
unmatched performance and the lowest power
consumptionfortheseindustrystandarddevices.
Refer to Figures 20 and 21 for supply current
performance characteristics rated against
temperature and supply voltages.
Table 2 shows how the SP705-708/813L
series can be used instead of the Dallas
Semiconductor DS1232LP/LPS. Table 2
illustratestoadesignertheadvantagesandtrade-
offs of the SP705-708/813L series
compared to the Dallas Semiconductor device.
While the names of the pin descriptions may
differ, the functions are the same or very similar.
June 2008 Rev C
SP705 Low Power Microprocessor Supervisory Circuits
© 2008 Exar Corporation
13
Dallas DS1232LP/LPS
Pin
Sipex Alternative Part Number
Pin Number
Function
Number
DIP or
SOIC
Pin
Description
Sipex Part
Pin Description
DIP or
SOIC
Number
µSOIC
3
SP705-708/
813L/813M
Manual Reset
WDI Time Delay Set
VCC Trip 4.6V
VCC Trip 4.4V
Ground
1
2
3
3
4
PBRST
TD
1
MR
SP705-708/
813L/813M
N/A
N/A
N/A
3
N/A
N/A
N/A
5
1.6sec by design
4.6V by design
4.4V by design
GND
SP705/707/
813L
TOL=GND
TOL=VCC
GND
SP706/708/
813M
SP705-708/
813L/813M
Reset Active HIGH
Reset Active HIGH
Reset Active LOW
5
5
6
RST
RST
RST
SP707/708
SP813L/813M
SP705-708
8
7
7
2
1
1
RESET
RESET
RESET
SP705/706/
813L/813M
Watchdog Input
Voltage Input
7
ST (H to L)
VCC
6
2
4
5
8
8
4
6
7
2
WDI (any trans.)
SP705-708/
813L/813M
8
VCC
PFI
SP705-708/
813L/813M
Power Fail Input
Power Fail Output
Watchdog Output
N/A
N/A
N/A
N/A
SP705-708/
813L/813M
N/A
PFO
WDO
SP705/706/
813L/813M
N/A
Table 2. Device Overview on Dallas Semiconductor
June 2008 Rev C
SP705 Low Power Microprocessor Supervisory Circuits
© 2008 Exar Corporation
14
June 2008 Rev C
SP705 Low Power Microprocessor Supervisory Circuits
© 2008 Exar Corporation
15
June 2008 Rev C
SP705 Low Power Microprocessor Supervisory Circuits
© 2008 Exar Corporation
16
June 2008 Rev C
SP705 Low Power Microprocessor Supervisory Circuits
© 2008 Exar Corporation
17
ORDERING INFORMATION
Model ....................................................................................... Temperature Range ................................................................................ Package
SP705CP .....................................................................................DISCONTINUED
SP705CN ....................................................................................... 0°C to +70°C ..................................................................... 8–pin Narrow SOIC
SP705CU ....................................................................................... 0°C to +70°C ................................................................................. 8-pin µSOIC
SP705EP ......................................................................................DISCONTINUED
SP705EN ..................................................................................... -40°C to +85°C ................................................................... 8–pin Narrow SOIC
SP705EU ..................................................................................... -40°C to +85°C ............................................................................... 8-pin µSOIC
SP706CP .....................................................................................DISCONTINUED
SP706CN ....................................................................................... 0°C to +70°C ..................................................................... 8–pin Narrow SOIC
SP706CU ....................................................................................... 0°C to +70°C ................................................................................. 8-pin µSOIC
SP706EP ......................................................................................DISCONTINUED
SP706EN ..................................................................................... -40°C to +85°C ................................................................... 8–pin Narrow SOIC
SP706EU ..................................................................................... -40°C to +85°C ............................................................................... 8-pin µSOIC
SP707CP .....................................................................................DISCONTINUED
SP707CN ....................................................................................... 0°C to +70°C ..................................................................... 8–pin Narrow SOIC
SP707CU ....................................................................................... 0°C to +70°C ................................................................................. 8-pin µSOIC
SP707EP ......................................................................................DISCONTINUED
SP707EN ..................................................................................... -40°C to +85°C ................................................................... 8–pin Narrow SOIC
SP707EU ..................................................................................... -40°C to +85°C ............................................................................... 8-pin µSOIC
SP708CP .....................................................................................DISCONTINUED
SP708CN ....................................................................................... 0°C to +70°C ..................................................................... 8–pin Narrow SOIC
SP708CU ....................................................................................... 0°C to +70°C ................................................................................. 8-pin µSOIC
SP708EP ......................................................................................DISCONTINUED
SP708EN ..................................................................................... -40°C to +85°C ................................................................... 8–pin Narrow SOIC
SP708EU ..................................................................................... -40°C to +85°C ............................................................................... 8-pin µSOIC
SP813LCP ..................................................................................... 0°C to +70°C ......................................................................... 8–pin Plastic DIP
SP813LCN ....................................................................................DISCONTINUED
SP813LCU ..................................................................................... 0°C to +70°C ................................................................................. 8-pin µSOIC
SP813LEP .................................................................................... -40°C to +85°C ....................................................................... 8–pin Plastic DIP
SP813LEN ....................................................................................DISCONTINUED
SP813LEU ................................................................................... -40°C to +85°C ............................................................................... 8-pin µSOIC
SP813MCP ...................................................................................DISCONTINUED
SP813MCN ...................................................................................DISCONTINUED
SP813MCU ...................................................................................DISCONTINUED
SP813MEP ....................................................................................DISCONTINUED
SP813MEN .................................................................................. DISCONTINUED
SP813MEU .................................................................................. DISCONTINUED
Please consult the factory for pricing and availability on a Tape-On-Reel option.
All parts available lead free and in tape & reel: Example SP708CU-L/TR
For further assistance:
Email:
customersupport@exar.com
EXAR Technical Documentation: http://www.exar.com/TechDoc/default.aspx?
Exar Corporation
Headquarters and
Sales Office
48720 Kato Road
Fremont, CA 94538
main: 510-668-7000
fax: 510-668-7030
EXAR Corporation reserves the right to make changes to the products contained in this publication in
order to improve design, performance or reliability. EXAR Corporation assumes no responsibility for the
use of any circuits described herein, conveys no license under any patent or other right, and makes no
representation that the circuits are free of patent infringement. Charts and schedules contained here in
are only for illustration purposes and may vary depending upon a user’s specific application. While the
information in this publication has been carefully checked; no responsibility, however, is assumed for
inaccuracies.
EXAR Corporation does not recommend the use of any of its products in life support applications where
the failure or malfunction of the product can reasonably be expected to cause failure of the life support
system or to significantly affect its safety or effectiveness. Products are not authorized for use in such
applications unless EXAR Corporation receives, in writing, assurances to its satisfaction that: (a) the risk
of injury or damage has been minimized; (b) the user assumes all such risks; (c) potential liability of
EXAR Corporation is adequately protected under the circumstances.
June 2008 Rev C
SP705 Low Power Microprocessor Supervisory Circuits
© 2008 Exar Corporation
18
相关型号:
SP706CP-L
Power Supply Support Circuit, Fixed, 1 Channel, PDIP8, LEAD FREE, PLASTIC, MS-001BA, DIP-8
SIPEX
©2020 ICPDF网 联系我们和版权申明