SM-762B [ETC]
DC Tachometer Generators; 直流测速发电机型号: | SM-762B |
厂家: | ETC |
描述: | DC Tachometer Generators |
文件: | 总8页 (文件大小:728K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
SERVO-TEK
®
SERVO-TEK PRODUCTS COMPANY, INC.
DC Tachometer Generators
www.servotek.com
RC-700 rev. 2
1086 Goffle Road • Hawthorne, NJ 07506 • sales@servotek.com
Phone (973) 427-3100 • Fax (973) 427-4249 • www.servotek.com
SERVO-TEK
®
Technical Data
An Industry Standard for over fifty years.
Linearity
A Servo-Tek DC tachometer generator provides a Linearity at any speed is better than 0.1% of the
convenient and economical means of converting output at that RPM.
rotational speed into an isolated analog voltage
signal suitable for remote indication and control. Bidirectional Operation
While this catalog contains information on our All Servo-Tek tachometer generators operate in
most popular models, we also manufacture either rotational direction. That direction can be
countless special tach generators.
determined by output voltage polarity. Output (in
either direction) is held to a tolerance of 0.25% of
the average output.
Construction
Most of our DC tach generators are housed in
aluminum casings protected in accordance with
Mil-C-5541 or Mil-A-8625 or high performance
plastics. Alnico permanent magnets are used.
Armature shafts are stainless-steel, and rotate
on fully shielded stainless-steel ball bearings.
Commutators are manufactured from an alloy
containing at least 90% silver.
Armature
laminations are wound with Isomid insulated wire,
over Teflon slot insulation. The entire armature
is then baked, resulting in a NEMA Class H
insulation system.
SB-740A-2
Stability
Optimum brush and commutator combination
gives 0.1% stability. Highly stable output gives no
evidence of long-term drift.
Breakdown Voltage
Servo-Tek DC tachometer generators are factory
tested with an AC potential of 1250 volts RMS
applied for one second between (either) terminal
and shaft. E-Series units are tested with 500 volts.
DA-7533A-2
Temperature Range
Most of our DC tachometer generators
Ripple
are
in
designed
ambient
for
continuous
operation
from
The ripple RMS value will not exceed 3% of the
DC value at any speed in excess of 40 RPM on
standard units. On the low ripple units, the ripple
RMS value will not exceed 1.5% of the DC value.
A peak to peak ripple of 1.5% is available on some
models.
temperatures
ranging
-55ºC to +100ºC. Voltage output at 25ºC will not
deviate by more than 0.01% per degree of change
within the range of -20ºC to +75ºC. All units are
temperature compensated, with the exception of
D-Series and E-Series tach generators.
1086 Goffle Road • Hawthorne, NJ 07506 • sales@servotek.com
Phone (973) 427-3100 • Fax (973) 427-4249 • www.servotek.com
SERVO-TEK
®
A-Series
B-Series
1 to 10 volts/1000 RPM
11 to 24 volts/1000 RPM
SB-757B-1 and SU-7346B-1
SA-757A-2 and SA-740A-2
SN-763A-2
A-Series Tachometer Generators
Instrument Type:
• 0.120 inch shaft diameter
• Small in size
B-Series Tachometer Generators
As is the case with the A-Series DC tachometer
generator, the B-Series also comes in instrument
and industrial configurations. Depending on the
unit, the output voltage ranges between 11 and 24
V/1000 RPM. Electrical characteristics, ripple,
linearity and temperature effects are the same as
the A-Series.
• Ideally suited to instrumentation applications
Industrial Type:
• 0.187 inch shaft diameter
• Special front-end bearings for radial loads
• Ideal for pulley and belt drive applications
Other shaft sizes and mounting configurations are
available for most Servo-Tek generators.
A-Series and B-Series Specifications
Inertia
(Approx.)
oz-in-sec2
Armature
Resistance
(dynamic)
Armature
Inductance
(henrys)
Shaft
Size
(in.)
Weight
V/1000
RPM
RPM
(max)
Outline
Dimensions Dimensions
Mounting
Model Number Mounting (Approx.)
SA-740A-7 Face
SB-740A-7 Flange 3.0 oz 1.32 x 10-4 2.6v 12,000
SA-740A-2 Face
3.0 oz 1.32 x 10-4 7.0v 12,000
SB-740A-2 Flange 3.0 oz 1.32 x 10-4 7.0v 12,000
SA-757A-2 Face
3.0 oz 1.32 x 10-4 7.0v 12,000
SB-757A-2 Flange 3.0 oz 1.32 x 10-4 7.0v 12,000
SA-740B-1 Face
4.0 oz 2.27 x 10-4 20.8v 8,000
SB-740B-1 Flange 4.0 oz 2.27 x 10-4 20.8v 8,000
SA-757B-1 Face
4.0 oz 2.27 x 10-4 20.8v 8,000
3.0 oz 1.32 x 10-4 2.6v 12,000
40Ω
40Ω
0.024h
0.024h
0.18h
0.18h
0.18h
0.18h
0.56h
0.56h
0.56h
0.56h
Fig. 10
Fig. 10
Fig. 10
Fig. 10
Fig. 11
Fig. 11
Fig. 10
Fig. 10
Fig. 11
Fig. 11
Fig. 1
Fig. 2
Fig. 1
Fig. 2
Fig. 1
Fig. 2
Fig. 1
Fig. 2
Fig. 1
Fig. 2
.120
.120
.120
.120
.187
.187
.120
.120
.187
.187
350Ω
350Ω
350Ω
350Ω
1000Ω
1000Ω
1000Ω
1000Ω
SB-757B-1 Flange 4.0 oz 2.27 x 10-4 20.8v 8,000
Maximum Driving Torque for A-Series and B-Series is 0.25 oz-in
Most units listed above are normally in stock
1086 Goffle Road • Hawthorne, NJ 07506 • sales@servotek.com
Phone (973) 427-3100 • Fax (973) 427-4249 • www.servotek.com
SERVO-TEK
®
D-Series
E-Series (Subminiature)
25 to 50 volts/1000 RPM
.7 to 3 volts/1000 RPM
SU-780D-1
SS-779E-1
D-Series Tachometer Generators
E-Series Tachometer Generators
The E-Series DC tachometer generator is the
smallest tach generator among those offering
With rugged construction and high output
voltages, the D-Series tach generator is ideally
suited to a variety of industrial applications.
similar technical characteristics.
Many
outstanding features make it particularly
suitable for use in all types of servo systems.
Although the diameter is only 0.760” the
E-Series provides up to 3 V/1000 RPM output.
The flange mounting arrangement provides a
convenient assembly method, and the sturdy
.187 shaft diameter permits the heavier loading
frequently encountered where pulleys or belt
drives are employed. The output bearing is fitted
with a seal to help prevent the contamination that
can occur in industrial applications.
Almost any Servo-Tek DC tachometer generator
can be manufactured with special configurations,
various electrical specs and shaft modifications
such as flats, pinions, holes, etc. Consult sales
department regarding your special requirements.
With output up to 50V/1000 RPM, D-Series
generators are ideal for applications where high
output voltages are required. Typically, these are
slow speed applications.
D-Series and E-Series Specifications
Inertia
(Approx.)
oz-in-sec2
Armature
Resistance
(dynamic)
Armature
Inductance
(henrys)
Shaft
Size
(in.)
Weight
V/1000
RPM
RPM
(max)
Outline
Dimensions Dimensions
Mounting
Model Number
Mounting (Approx.)
SU-780D-1 Flange 8.5 oz 4.54 x 10-4
SU-7114D-1 Flange 8.5 oz 4.54 x 10-4
SU-780D-2 Flange 8.5 oz 4.54 x 10-4
SS-779E-1 Synchro 1.25 oz 0.25 x 10-4
45v
45v
33v
3v
5,000
5,000
5,000
12,000
1750Ω
1750Ω
950Ω
1.00h
1.00h
0.54h
0.061h
Fig. 10
Fig. 10
Fig. 10
Fig. 12
Fig. 5
Fig. 5
Fig. 5
Fig. 6
.187
.187
.187
.120
180Ω
Maximum Driving Torque for D-Series and E-Series is 0.25 oz-in
Most units listed above are normally in stock
1086 Goffle Road • Hawthorne, NJ 07506 • sales@servotek.com
Phone (973) 427-3100 • Fax (973) 427-4249 • www.servotek.com
SERVO-TEK
®
Low Ripple Units (F-Series, H-Series and J-Series)
1 to 30 volts/1000 RPM
CS-7514F-51C and SA-7356F-1
SB-7483H-1
F-Series (1-8 volts/1000 RPM)
H-Series (5-16 volts/1000 RPM)
Servo-Tek low ripple DC tachometer generators
satisfy the need for a cost effective, very
low ripple tachometer. In addition to being the
first economical low ripple units of their type, the
F-Series tachometers incorporate all the desirable
features of the standard units such as temperature
compensation, long brush life, excellent linearity,
and small dimensions.
The H-Series DC tachometer generators are low
ripple units possessing all the same traits as the
F-Series, but with the B-length armature. This
means a slightly higher output voltage.
J-Series (16-30 volts/1000 RPM)
The J-Series DC tachometer generators are low
ripple units possessing all the same traits as the
F-Series, but with the D-length armature. These
generators are ideal for applications where high
outputvoltageswithlowripplesignalsarerequired.
The ripple voltage does not exceed 1.5% RMS
and 3.5% peak to peak at any speed in excess of
40 RPM on any F-Series, H-Series or J-Series DC
tachometer generator.
Other shaft sizes and mounting configurations are
available.
F-Series, H-Series and J-Series Specifications
Inertia
(Approx.)
oz-in-sec2
Armature
Resistance Inductance
(dynamic)
Armature
Shaft
Size
(in.)
Weight
RPM
(max)
Outline
Dimensions Dimensions
Mounting
Model Number
Mounting (Approx.)
V/1000 RPM
(henrys)
SA-7356F-1
Face
Face
3.0 oz 1.14 x 10-4 7.0v ± 3% 12,000 500Ω
3.0 oz 1.32 x 10-4 7.0v ± 3% 12,000 500Ω
0.38h
Fig. 10
Fig. 10
Fig. 1
Fig. 1
Fig. 3
Fig. 2
Fig. 5
.120
.187
.250
.187
.187
SA-7388F-1
0.38h
CS-7514F-51C Flange 3.0 oz 1.32 x 10-4 3.0v ± 3% 12,000 130Ω
0.061h Fig. 11
SB-7483H-1
SU-780J-1
Flange 4.0 oz 1.96 x 10-4 16.0v ± 3% 8,000
Flange 8.5 oz 4.54 x 10-4 30v ± 1%
5,000 1050Ω
800Ω
0.72h
1.00h
Fig. 11
Fig. 10
Maximum Driving Torque for F-Series, H-Series and J-Series is 0.25 oz-in at 25ºC
Most units listed above are normally in stock
1086 Goffle Road • Hawthorne, NJ 07506 • sales@servotek.com
Phone (973) 427-3100 • Fax (973) 427-4249 • www.servotek.com
SERVO-TEK
®
Sealed DC Tachometers Servo-Tek’s Ruggedized
1 to 45 volts/1000 RPM
PY Alternative (Up to 50 volts)
ST-7337A-2N and ST-7337B-1
ST-13212 and ST-12970
Sealed Tachometer Generators
Ruggedized Tachometer Generators
Servo-Tek manufactures a complete line of sealed
units which are resistant against the harmful
effects of fluids. These units employ a one-piece
housing, a special shaft seal, and a form-fitted
rubber boot on the terminal end. Servo-Tek sealed
units meet electrical specifications after storage at
49ºC with 95% relative humidity for 24 hours.
These units are capable of enduring vibration
with amplitudes up to 0.03” total excursion at
frequencies from 4 Hz to 55 Hz in each of three
mutually perpendicular axes with no evidence of
physical damage. These units are available with a
low ripple output up to 30V/1000 RPM.
Servo-Tek ruggedized DC tachometer generators
are designed with sturdy aluminum housings and
strong mounting flanges. Other features offered
include extra-heavy armature shafts and bearings.
The mechanical flexibility of the ST-13212 allows
for the internal tachometer to be repaired or
replaced, without having to replace the expensive
anodized casting. The ST-13212 supplies outputs
from 2.6 to 50V/1000 RPM and runs at speeds
up to 5000 RPM. The shaft size is 5/16” in
diameter. The ST-12970 comes equipped with a
rubber coupling. It allows the unit to be driven
by a motor shaft with 0.167” wide slot. The
ST-12970 is also available with outputs up to
24V/1000 RPM and can run at high speeds.
Sealed DC Tachometer Generator Specifications
Inertia
(Approx.)
oz-in-sec2
Armature
Resistance
(dynamic)
Armature
Inductance
(henrys)
Shaft
Size
(in.)
Weight
V/1000
RPM
RPM
(max)
Outline
Dimensions Dimensions
Mounting
Model Number
Mounting (Approx.)
ST-7336A-7
Face
Face
Face
Face
Face
3.0 oz 1.32 x 10-4 2.6v 12,000
40Ω
0.024h
0.18h
0.56h
0.18h
0.56h
1.00h
Fig. 8
Fig. 8
Fig. 8
Fig. 8
Fig. 8
Fig. 8
Fig. 8
Fig. 8
Fig. 8
Fig. 8
Fig. 8
Fig. 5
.120
.120
.120
.187
.187
.187
ST-7336A-2
ST-7336B-1
ST-7337A-2
ST-7337B-1
3.0 oz 1.32 x 10-4 7.0v 12,000 350Ω
4.0 oz 2.27 x 10-4 20.8v 8,000 1000Ω
3.0 oz 1.32 x 10-4 7.0v 12,000 350Ω
4.0 oz 2.27 x 10-4 20.8v 8,000 1000Ω
SU-7346D-1 Flange 8.5 oz 4.54 x 10-4
45v
5,000 1750Ω
Maximum Driving Torque for a sealed DC tachometer generator is 0.7 oz-in
Most units listed above are normally in stock
1086 Goffle Road • Hawthorne, NJ 07506 • sales@servotek.com
Phone (973) 427-3100 • Fax (973) 427-4249 • www.servotek.com
SERVO-TEK
®
Overhung Tachometer
1 to 24 volts/1000 RPM
ST-7565 Series
Introducing Servo-Tek’s new low-cost overhung
tachometer. This bearingless tach-generator is
small in size and has a black delrin housing and
end plate. Because the Servo-Tek overhung unit
is self-generating and provides an analog output,
it makes for an excellent alternative to the encoder.
No D-A conversion will be necessary! Mounts
easily using a 10-32 threaded shaft. No coupling or
mounting brackets will be required.
ST-7565A-2
Part Number: ST-7565A-2
Output Voltage: 7 VDC ± 5%, no load, per 1000 RPM at 25ºC
Internal Resistance: 270 Ohms typical at 25ºC
Ripple: 5% RMS of DC output voltage at speeds over 40 RPM
Linearity: 0.1% max., 0 to 4000 RPM
Bidirectional Output: 0.5% of nominal output in both CW and CCW directions
Polarity: Red wire positive with CCW rotation viewing shaft end
Temperature Coefficient: 0.05% per ºC of nominal output at 25ºC from -20ºC to 50ºC
Accessories
Other Products
Rubber Couplings
ST-9502-1 fits .120
shafts and ST-9502-2
fits .187 shafts. The
tapered tang is molded
to fit a straight slot
0.167”±.005” wide and
3/16” deep.
ST50 Optical Encoder
The ST50, a 2 inch
hollow shaft encoder,
accepts
from .236 to .625 inches
OD. It combines 3 phase
brushless
motor
shafts
commutation
pulses, 2 data channels
and reference index pulse
in a single package.
ST-9502
ST50
Flexible Couplings
ST20 Optical Encoder
The ST20, a 2 inch shaft
encoder, is a low cost,
heavy duty solution to
ST-9776
fits
shaft
diameters of up to .375
shafts. They may be
ordered in any mixed or
matched configuration.
When ordering, please
specify both hole sizes.
digital feedback.
This
unit is available in single
or dual channel with
nearly unlimited mounting
patterns.
ST-9776
ST20
Request a Servo-Tek RC-800 catalog for our complete product line of encoders.
Mounting and Outline Dimensions
Figure 1 SA Face Mount
Figure 2 SB Flange Mount
Figure 3 SD Modified Synchro
Figure 4 SM Aircraft Mount
Figure 5 SU Large Flange Mount
Figure 6 SS Synchro Mount
Figure 7 Aircraft Configuration
Figure 8 Sealed Configuration
Figure 9 Flat Shaft Configuration
Model #
SM-762A
SM-762B
“L”
2.520
2.957
Model “L” “F” “P” “N”
ST-7336A 1.867 OMIT OMIT OMIT 0.120 ± .001
“S”
Model “L” “E” “F” “N”
“S”
XX-7114B 2.193 0.562 0.437 0.157 0.187 ± .001
XX-7114D 3.253 0.562 0.437 0.157 0.187 ± .001
XX-7146A 1.701 0.562 0.437 0.110 0.120 ± .001
ST-7336B 2.304 OMIT OMIT OMIT 0.120 ± .001
ST-7337A 1.875 0.375
ST-7337B 2.312 0.375
XX-7346D 3.633 0.375
0.062 0.157 0.187 ± .001
0.062 0.157 0.187 ± .001
0.062 0.157 0.187 ± .001
Figure 10 Instrument/Industrial Configuration
Figure 11 Industrial Configuration
Figure 12 E-Series Tachometers
Model # “L” “F” “P”
“N”
Model # “L” “F” “P”
“N”
“S”
Model # “T” “L”
“E”
“S”
XX-757A
XX-757B
XX-796B
XX-7483H
2.240
2.677
2.677
2.677
0.375
0.062
0.157
XX-740A
XX-740B
XX-780B
XX-780D
XX-797A
XX-7103A
XX-7107D
XX-7123A
XX-7123B
XX-7356F
XX-7360F
1.701
2.138
2.193
3.253
1.701
1.756
3.253
1.756
2.193
1.701
1.756
OMIT OMIT
OMIT
0.120 ± .001
SS-779E
1.687
1.479 0.375 ± .015 0.1200 ± .0005
0.375
0.062
0.157
OMIT
0.157
OMIT OMIT
OMIT
0.157
0.157
0.110
0.157
OMIT
OMIT
OMIT
OMIT
0.157
0.120 ± .001
0.187 ± .001
0.187 ± .001
0.120 ± .001
0.187 ± .001
0.187 ± .001
0.187 ± .001
0.187 ± .001
0.120 ± .001
0.187 ± .001
SS-7251E
1.687
1.479 0.562 ± .015 0.1870 ± .0002
OMIT OMIT
0.375 0.062
0.375
0.375
0.187
0.375
0.062
0.062
0.187
0.062
OMIT OMIT
OMIT OMIT
OMIT OMIT
OMIT OMIT
Servo-Tek Products Company • 1086 Goffle Road • Hawthorne, NJ 07506
Phone (973) 427-3100 • Fax (973) 427-4249 • www.servotek.com
Specifications subject to change without notice
Copyright © 2003 Servo-Tek Products Company
0.375
0.062
相关型号:
©2020 ICPDF网 联系我们和版权申明