PSD813F3V [ETC]
FLASH IN-SYSTEM PROGRAMMABLE (ISP) PERIPHERALS FOR 8-BIT MCUS ; FLASH在系统可编程（ ISP）外设的8位微控制器\n
| 型号： | PSD813F3V |
| 厂家： | 
ETC |
| 描述： | FLASH IN-SYSTEM PROGRAMMABLE (ISP) PERIPHERALS FOR 8-BIT MCUS
|
| 文件： | 总103页 (文件大小：1127K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
PSD81XFX, PSD83XF2, PSD85XF2
Flash In-System Programmable
(ISP) Peripherals For 8-bit MCUs
PRELIMINARY DATA
FEATURES SUMMARY
■ 5V±10% Single Supply Voltage
Figure 1. 52-pin, Plastic, Quad, Flat Package
■ Up to 2Mbit of Primary Flash Memory (8 uniform
sectors, 32K x 8)
■ Up to 256Kbit Secondary Flash Memory (4
uniform sectors)
PQFP52 (T)
■ Up to 256Kbit SRAM
■ Over 3,000 Gates of PLD: DPLD and CPLD
■ 27 Reconfigurable I/O ports
■ Enhanced JTAG Serial Port
■ Programmable power management
■ High Endurance:
Figure 2. 52-lead, Plastic-Lead Chip Carrier
– 100,000 Erase/WRITE Cycles of Flash
Memory
– 1,000 Erase/WRITE Cycles of PLD
PLCC52 (K)
October 2003
1/103
This is preliminary information on a new product now in development or undergoing evaluation. Details are subject to change without notice.
Rev. 3.2
PSD81XFX, PSD83XF2, PSD85XF2
TABLE OF CONTENTS
SUMMARY DESCRIPTION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Table 1. Product Range (Note 1). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
KEY FEATURES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Figure 3. PSD8XXFX Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
PSD8XXFX ARCHITECTURAL OVERVIEW . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Memory. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Page Register. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
PLDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Table 2. PLD I/O . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
I/O Ports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
MCU Bus Interface. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
JTAG Port. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
In-System Programming (ISP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Power Management Unit (PMU) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Table 3. JTAG SIgnals on Port C . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Table 4. Methods of Programming Different Functional Blocks of the PSD8XXFX. . . . . . . . . . . . . 12
DEVELOPMENT SYSTEM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Figure 4. PSDsoft Express Development Tool . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
PIN DESCRIPTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Table 5. Pin Description (for the PLCC52 package - Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
PSD8XXFX Register Description and Address Offset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Table 6. I/O Port Latched Address Output Assignments (Note1) . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Table 7. Register Address Offset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
DETAILED OPERATION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
MEMORY BLOCKS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Primary Flash Memory and Secondary Flash memory Description . . . . . . . . . . . . . . . . . . . . . 18
Memory Block Select Signals. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Table 8. Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Power-down Instruction and Power-up Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
2/103
PSD81XFX, PSD83XF2, PSD85XF2
READ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Table 9. Status Bit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Programming Flash Memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Figure 5. Data Polling Flowchart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Figure 6. Data Toggle Flowchart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Erasing Flash Memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Specific Features. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Table 10. Sector Protection/Security Bit Definition – Flash Protection Register . . . . . . . . . . . . . . . 25
Table 11. Sector Protection/Security Bit Definition – PSD/EE Protection Register . . . . . . . . . . . . . 25
SRAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Sector Select and SRAM Select . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Figure 7. Priority Level of Memory and I/O Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Table 12. VM Register. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Figure 8. 8031 Memory Modules – Separate Space. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Figure 9. 8031 Memory Modules – Combined Space . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Page Register. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Figure 10. Page Register. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
PLDS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Table 13. DPLD and CPLD Inputs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
The Turbo Bit in PSD8XXFX . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Figure 11. PLD Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Decode PLD (DPLD) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Figure 12. DPLD Logic Array. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Complex PLD (CPLD) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Figure 13. Macrocell and I/O Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Output Macrocell (OMC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Table 14. Output Macrocell Port and Data Bit Assignments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Product Term Allocator. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Figure 14. CPLD Output Macrocell . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Input Macrocells (IMC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Figure 15. Input Macrocell . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Figure 16. Handshaking Communication Using Input Macrocells . . . . . . . . . . . . . . . . . . . . . . . . . . 39
MCU BUS INTERFACE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Table 15. MCUs and their Control Signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Figure 17. An Example of a Typical 8-bit Multiplexed Bus Interface . . . . . . . . . . . . . . . . . . . . . . . . 41
Figure 18. An Example of a Typical 8-bit Non-Multiplexed Bus Interface . . . . . . . . . . . . . . . . . . . . 42
Table 16. Eight-Bit Data Bus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
3/103
PSD81XFX, PSD83XF2, PSD85XF2
MCU Bus Interface Examples . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Figure 19. Interfacing the PSD8XXFX with an 80C31. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Table 17. 80C251 Configurations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Table 18. Interfacing the PSD8XXFX with the 80C251, with One READ Input. . . . . . . . . . . . . . . . 44
Figure 20. Interfacing the PSD8XXFX with the 80C251, with RD and PSEN Inputs. . . . . . . . . . . . 45
Figure 21. Interfacing the PSD8XXFX with the 80C51X, 8-bit Data Bus. . . . . . . . . . . . . . . . . . . . . 46
Figure 22. Interfacing the PSD8XXFX with a 68HC11 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
I/O PORTS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
General Port Architecture. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
Figure 23. General I/O Port Architecture . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
Port Operating Modes. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
MCU I/O Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
PLD I/O Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
Address Out Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
Table 19. Port Operating Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
Table 20. Port Operating Mode Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
Table 21. I/O Port Latched Address Output Assignments. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
Address In Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
Data Port Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
Peripheral I/O Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
JTAG In-System Programming (ISP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
Figure 24. Peripheral I/O Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
Port Configuration Registers (PCR) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
Table 22. Port Configuration Registers (PCR) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
Table 23. Port Pin Direction Control, Output Enable P.T. Not Defined . . . . . . . . . . . . . . . . . . . . . . 52
Table 24. Port Pin Direction Control, Output Enable P.T. Defined . . . . . . . . . . . . . . . . . . . . . . . . . 52
Table 25. Port Direction Assignment Example . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
Table 26. Drive Register Pin Assignment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
Port Data Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
Table 27. Port Data Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
Ports A and B – Functionality and Structure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
Figure 25. Port A and Port B Structure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
Port C – Functionality and Structure. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
Figure 26. Port C Structure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
Port D – Functionality and Structure. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
Figure 27. Port D Structure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
External Chip Select . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
Figure 28. Port D External Chip Select Signals. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
4/103
PSD81XFX, PSD83XF2, PSD85XF2
POWER MANAGEMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
Table 28. Power-down Mode’s Effect on Ports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
Figure 29. APD Unit. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
Table 29. PSD8XXFX Timing and Stand-by Current during Power-down Mode. . . . . . . . . . . . . . . 59
Figure 30. Enable Power-down Flow Chart. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
PLD Power Management. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
Table 30. Power Management Mode Registers PMMR0 (Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . 61
Table 31. Power Management Mode Registers PMMR2 (Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . 61
PSD Chip Select Input (CSI, PD2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
Input Clock. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
Input Control Signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
Table 32. APD Counter Operation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
RESET TIMING AND DEVICE STATUS AT RESET . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
Warm Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
I/O Pin, Register and PLD Status at Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
Reset of Flash Memory Erase and Program Cycles (on the PSD834Fx) . . . . . . . . . . . . . . . . . 63
Figure 31. Reset (RESET) Timing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
Table 33. Status During Power-On Reset, Warm Reset and Power-down Mode . . . . . . . . . . . . . . 64
PROGRAMMING IN-CIRCUIT USING THE JTAG SERIAL INTERFACE . . . . . . . . . . . . . . . . . . . . . . 65
Standard JTAG Signals. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
Table 34. JTAG Port Signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
JTAG Extensions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
Security and Flash memory Protection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
INITIAL DELIVERY STATE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
Table 35. JTAG Enable Register. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
AC/DC PARAMETERS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
Figure 32. PLD ICC /Frequency Consumption (5 V range). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
Figure 33. PLD ICC /Frequency Consumption (3 V range). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68
Table 36. Example of PSD8XXFX Typical Power Calculation at V = 5.0 V (Turbo Mode On) . . 69
CC
Table 37. Example of PSD8XXFX Typical Power Calculation at V = 5.0 V (Turbo Mode Off) . . 70
CC
MAXIMUM RATING. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71
Table 38. Absolute Maximum Ratings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71
5/103
PSD81XFX, PSD83XF2, PSD85XF2
DC AND AC PARAMETERS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72
Table 39. Operating Conditions (5V devices) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72
Table 40. Operating Conditions (3V devices) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72
Table 41. AC Measurement Conditions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72
Figure 34. AC Measurement I/O Waveform . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72
Figure 35. AC Measurement Load Circuit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72
Table 42. Capacitance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72
Table 43. AC Symbols for PLD Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73
Figure 36. Switching Waveforms – Key. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73
Table 44. DC Characteristics (5V devices) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74
Table 45. DC Characteristics (3V devices) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75
Figure 37. Input to Output Disable / Enable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76
Table 46. CPLD Combinatorial Timing (5V devices) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76
Table 47. CPLD Combinatorial Timing (3V devices) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76
Figure 38. Synchronous Clock Mode Timing – PLD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77
Table 48. CPLD Macrocell Synchronous Clock Mode Timing (5V devices) . . . . . . . . . . . . . . . . . . 77
Table 49. CPLD Macrocell Synchronous Clock Mode Timing (3V devices) . . . . . . . . . . . . . . . . . . 78
Figure 39. Asynchronous Reset / Preset. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79
Figure 40. Asynchronous Clock Mode Timing (product term clock) . . . . . . . . . . . . . . . . . . . . . . . . 79
Table 50. CPLD Macrocell Asynchronous Clock Mode Timing (5V devices) . . . . . . . . . . . . . . . . . 80
Table 51. CPLD Macrocell Asynchronous Clock Mode Timing (3V devices) . . . . . . . . . . . . . . . . . 81
Figure 41. Input Macrocell Timing (product term clock) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82
Table 52. Input Macrocell Timing (5V devices) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82
Table 53. Input Macrocell Timing (3V devices) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82
Figure 42. READ Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83
Table 54. READ Timing (5V devices) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84
Table 55. READ Timing (3V devices) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85
Figure 43. WRITE Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86
Table 56. WRITE Timing (5V devices) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87
Table 57. WRITE Timing (3V devices) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88
Table 58. Program, WRITE and Erase Times (5V devices) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89
Table 59. Program, WRITE and Erase Times (3V devices) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89
Figure 44. Peripheral I/O READ Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90
Table 60. Port A Peripheral Data Mode READ Timing (5V devices). . . . . . . . . . . . . . . . . . . . . . . . 90
Table 61. Port A Peripheral Data Mode READ Timing (3V devices). . . . . . . . . . . . . . . . . . . . . . . . 91
Figure 45. Peripheral I/O WRITE Timing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92
Table 62. Port A Peripheral Data Mode WRITE Timing (5V devices) . . . . . . . . . . . . . . . . . . . . . . . 92
Table 63. Port A Peripheral Data Mode WRITE Timing (3V devices) . . . . . . . . . . . . . . . . . . . . . . . 92
Figure 46. Reset (RESET) Timing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93
Table 64. Reset (RESET) Timing (5V devices) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93
Table 65. Reset (RESET) Timing (3V devices) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93
Table 66. V
Table 67. V
Timing (5V devices) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93
Timing (3V devices) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93
STBYON
STBYON
6/103
PSD81XFX, PSD83XF2, PSD85XF2
Figure 47. ISC Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94
Table 68. ISC Timing (5V devices) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94
Table 69. ISC Timing (3V devices) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95
Table 70. Power-down Timing (5V devices) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95
Table 71. Power-down Timing (3V devices) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95
PACKAGE MECHANICAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96
Figure 48. PQFP52 Connections. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96
Figure 49. PLCC52 Connections. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96
Figure 50. PQFP52 - 52-pin Plastic, Quad, Flat Package Mechanical Drawing . . . . . . . . . . . . . . . 96
Table 72. PQFP52 - 52-pin Plastic, Quad, Flat Package Mechanical Dimensions . . . . . . . . . . . . . 97
Figure 51. PLCC52 - 52-lead Plastic Lead, Chip Carrier Package Mechanical Drawing . . . . . . . . 98
Table 73. PLCC52 - 52-lead Plastic Lead, Chip Carrier Package Mechanical Dimensions . . . . . . 98
PART NUMBERING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99
Table 74. Ordering Information Scheme . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99
APPENDIX A. PQFP52 PIN ASSIGNMENTS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100
APPENDIX B. PLCC52 PIN ASSIGNMENTS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101
REVISION HISTORY. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 102
7/103
PSD81XFX, PSD83XF2, PSD85XF2
SUMMARY DESCRIPTION
The PSD8XXFX family of memory systems for mi-
crocontrollers (MCUs) brings In-System-Program-
mability (ISP) to Flash memory and programmable
logic. The result is a simple and flexible solution for
embedded designs. PSD8XXFX devices combine
many of the peripheral functions found in MCU
based applications.
– First-time In-System Programming (ISP)
– Complex address decoding
– Simultaneous read and write to the device.
The JTAG Serial Interface block allows In-System
Programming (ISP), and eliminates the need for
an external Boot EPROM, or an external program-
mer. To simplify Flash memory updates, program
execution is performed from a secondary Flash
memory while the primary Flash memory is being
updated. This solution avoids the complicated
hardware and software overhead necessary to im-
plement IAP.
ST makes available a software development tool,
PSDsoft Express, that generates ANSI-C compli-
ant code for use with your target MCU. This code
allows you to manipulate the non-volatile memory
(NVM) within the PSD8XXFX. Code examples are
also provided for:
– Flash memory IAP via the UART of the host
MCU
– Memory paging to execute code across several
PSD8XXFX memory pages
– Loading, reading, and manipulation of
PSD8XXFX macrocells by the MCU.
Table 1 summarizes all the devices in the
PSD834F2, PSD853F2, PSD854F2.
The CPLD in the PSD8XXFX devices features an
optimized macrocell logic architecture. The PSD
macrocell was created to address the unique re-
quirements of embedded system designs. It al-
lows direct connection between the system
address/data bus, and the internal PSD8XXFX
registers, to simplify communication between the
MCU and other supporting devices.
The PSD8XXFX device includes a JTAG Serial
Programming interface, to allow In-System Pro-
gramming (ISP) of the entire device. This feature
reduces development time, simplifies the manu-
facturing flow, and dramatically lowers the cost of
field upgrades. Using ST’s special Fast-JTAG pro-
gramming, a design can be rapidly programmed
into the PSD8XXFX in as little as seven seconds.
The innovative PSD8XXFX family solves key
problems faced by designers when managing dis-
crete Flash memory devices, such as:
Table 1. Product Range (Note 1)
Number of
Macrocells
Serial
ISP
JTAG/
Primary Flash
Memory
(8 Sectors)
Secondary
Flash Memory
(4 Sectors)
Turbo
Mode
2
Part Number
I/O Ports
SRAM
Input
Output
16
ISC Port
PSD813F2
PSD813F3
PSD813F4
PSD813F5
PSD833F2
PSD834F2
PSD853F2
PSD854F2
1 Mbit
1 Mbit
1 Mbit
1 Mbit
1 Mbit
2 Mbit
1 Mbit
2 Mbit
256 Kbit
none
16 Kbit
16 Kbit
none
27
27
27
27
27
27
27
27
24
24
24
24
24
24
24
24
yes
yes
yes
yes
yes
yes
yes
yes
yes
yes
yes
yes
yes
yes
yes
yes
16
256 Kbit
none
16
none
16
256 Kbit
256 Kbit
256 Kbit
256 Kbit
64 Kbit
64 Kbit
256 Kbit
256 Kbit
16
16
16
16
Note: 1. All products support: JTAG serial ISP, MCU parallel ISP, ISP Flash memory, ISP CPLD, Security features, Power Management
Unit (PMU), Automatic Power-down (APD)
2. SRAM may be backed up using an external battery.
8/103
PSD81XFX, PSD83XF2, PSD85XF2
KEY FEATURES
■ A simple interface to 8-bit microcontrollers that
use either multiplexed or non-multiplexed
busses. The bus interface logic uses the control
signals generated by the microcontroller
automatically when the address is decoded and
a READ or WRITE is performed. A partial list of
the MCU families supported include:
■ Decode PLD (DPLD) that decodes address for
selection of internal memory blocks.
■ 27 individually configurable I/O port pins that
can be used for the following functions:
– MCU I/Os
– PLD I/Os
– Latched MCU address output
– Special function I/Os.
– Intel 8031, 80196, 80186, 80C251, and
80386EX
– Motorola 68HC11, 68HC16, 68HC12, and
683XX
– 16 of the I/O ports may be configured as
open-drain outputs.
– Philips 8031 and 8051XA
– Zilog Z80 and Z8
■ Internal 1 or 2 Mbit Flash memory. This is the
main Flash memory. It is divided into eight
equal-sized blocks that can be accessed with
user-specified addresses.
■ Internal secondary 256 Kbit Flash boot memory.
It is divided into four equal-sized blocks that can
be accessed with user-specified addresses.
This secondary memory brings the ability to
execute code and update the main Flash
concurrently.
■ Optional 16, 64 or 256 Kbit SRAM. The SRAM’s
contents can be protected from a power failure
by connecting an external battery.
■ Standby current as low as 50 µA for 5 V devices.
■ Built-in JTAG compliant serial port allows full-
chip In-System Programmability (ISP). With it,
you can program a blank device or reprogram a
device in the factory or the field.
■ Internal page register that can be used to
expand the microcontroller address space by a
factor of 256.
■ Internal programmable Power Management
Unit (PMU) that supports a low power mode
called Power Down Mode. The PMU can
automatically detect a lack of microcontroller
activity and put the PSD8XXF into Power-down
mode.
■ Erase/WRITE cycles:
■ CPLD with 16 Output Micro Cells (OMCs) and
24 Input Micro Cells (IMCs). The CPLD may be
used to efficiently implement a variety of logic
functions for internal and external control.
Examples include state machines, loadable
shift registers, and loadable counters.
– Flash memory – 100,000 minimum
– PLD – 1,000 minimum
– Data Retention: 15 year minimum (for Main
Flash memory, Boot, PLD and Configuration
bits)
9/103
PSD81XFX, PSD83XF2, PSD85XF2
Figure 3. PSD8XXFX Block Diagram
AI02861E
10/103
PSD81XFX, PSD83XF2, PSD85XF2
PSD8XXFX ARCHITECTURAL OVERVIEW
PSD8XXFX devices contain several major func-
tional blocks. Figure 3 shows the architecture of
the PSD8XXFX device family. The functions of
each block are described briefly in the following
sections. Many of the blocks perform multiple
functions and are user configurable.
Table 2. PLD I/O
Product
Terms
Name
Inputs Outputs
Decode PLD (DPLD)
73
17
19
42
Complex PLD (CPLD) 73
140
Memory
The DPLD is used to decode addresses and to
generate Sector Select signals for the PSD8XXFX
internal memory and registers. The DPLD has
combinatorial outputs. The CPLD has 16 Output
Macrocells (OMC) and 3 combinatorial outputs.
The PSD8XXFX also has 24 Input Macrocells
(IMC) that can be configured as inputs to the
PLDs. The PLDs receive their inputs from the PLD
Input Bus and are differentiated by their output
destinations, number of product terms, and mac-
rocells.
The PLDs consume minimal power. The speed
and power consumption of the PLD is controlled
by the Turbo bit in PMMR0 and other bits in the
PMMR2. These registers are set by the MCU at
run-time. There is a slight penalty to PLD propaga-
tion time when invoking the power management
features.
Each of the memory blocks is briefly discussed in
the following paragraphs. A more detailed discus-
sion can be found in the section entitled “MEMO-
RY BLOCKS“ on page 18.
The 1 Mbit or 2 Mbit (128K x 8, or 256K x 8) Flash
memory is the primary memory of the PSD8XXFX.
It is divided into 8 equally-sized sectors that are in-
dividually selectable.
The optional 256 Kbit (32K x 8) secondary Flash
memory is divided into 4 equally-sized sectors.
Each sector is individually selectable.
The optional SRAM is intended for use as a
scratch-pad memory or as an extension to the
MCU SRAM. If an external battery is connected to
Voltage Stand-by (V , PC2), data is retained in
STBY
the event of power failure.
Each sector of memory can be located in a differ-
ent address space as defined by the user. The ac-
cess times for all memory types includes the
address latching and DPLD decoding time.
I/O Ports
The PSD8XXFX has 27 individually configurable I/
O pins distributed over the four ports (Port A, B, C,
and D). Each I/O pin can be individually configured
for different functions. Ports can be configured as
standard MCU I/O ports, PLD I/O, or latched ad-
dress outputs for MCUs using multiplexed ad-
dress/data buses.
Page Register
The 8-bit Page Register expands the address
range of the MCU by up to 256 times. The paged
address can be used as part of the address space
to access external memory and peripherals, or in-
ternal memory and I/O. The Page Register can
also be used to change the address mapping of
sectors of the Flash memories into different mem-
ory spaces for IAP.
The JTAG pins can be enabled on Port C for In-
System Programming (ISP).
Ports A and B can also be configured as a data
port for a non-multiplexed bus.
PLDs
MCU Bus Interface
The device contains two PLDs, the Decode PLD
(DPLD) and the Complex PLD (CPLD), as shown
in Table 2, each optimized for a different function.
The functional partitioning of the PLDs reduces
power consumption, optimizes cost/performance,
and eases design entry.
PSD8XXFX interfaces easily with most 8-bit
MCUs that have either multiplexed or non-multi-
plexed address/data buses. The device is config-
ured to respond to the MCU’s control signals,
which are also used as inputs to the PLDs. For ex-
amples, please see the section entitled “MCU Bus
Interface Examples“ on page 43.
11/103
PSD81XFX, PSD83XF2, PSD85XF2
JTAG Port
In-System Programming (ISP) can be performed
through the JTAG signals on Port C. This serial in-
terface allows complete programming of the entire
PSD8XXFX device. A blank device can be com-
pletely programmed. The JTAG signals (TMS,
TCK, TSTAT, TERR, TDI, TDO) can be multi-
plexed with other functions on Port C. Table 3 in-
dicates the JTAG pin assignments.
MCU inactivity. The APD Unit has a Power-down
mode that helps reduce power consumption.
The PSD8XXFX also has some bits that are con-
figured at run-time by the MCU to reduce power
consumption of the CPLD. The Turbo bit in
PMMR0 can be reset to 0 and the CPLD latches its
outputs and goes to sleep until the next transition
on its inputs.
In-System Programming (ISP)
Additionally, bits in PMMR2 can be set by the
MCU to block signals from entering the CPLD to
reduce power consumption. Please see the sec-
tion entitled “POWER MANAGEMENT” on page
58 for more details.
Using the JTAG signals on Port C, the entire
PSD8XXFX device can be programmed or erased
without the use of the MCU. The primary Flash
memory can also be programmed in-system by
the MCU executing the programming algorithms
out of the secondary memory, or SRAM. The sec-
ondary memory can be programmed the same
way by executing out of the primary Flash memo-
ry. The PLD or other PSD8XXFX Configuration
blocks can be programmed through the JTAG port
or a device programmer. Table 4 indicates which
programming methods can program different func-
tional blocks of the PSD8XXFX.
Table 3. JTAG SIgnals on Port C
Port C Pins
PC0
JTAG Signal
TMS
TCK
PC1
PC3
PC4
PC5
PC6
TSTAT
TERR
TDI
Power Management Unit (PMU)
The Power Management Unit (PMU) gives the
user control of the power consumption on selected
functional blocks based on system requirements.
The PMU includes an Automatic Power-down
(APD) Unit that turns off device functions during
TDO
Table 4. Methods of Programming Different Functional Blocks of the PSD8XXFX
Functional Block
Primary Flash Memory
JTAG Programming Device Programmer
IAP
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
No
Secondary Flash Memory
PLD Array (DPLD and CPLD)
PSD8XXFX Configuration
No
12/103
PSD81XFX, PSD83XF2, PSD85XF2
DEVELOPMENT SYSTEM
The PSD8XXFX family is supported by PSDsoft
Express, a Windows-based software development
tool. A PSD8XXFX design is quickly and easily
produced in a point and click environment. The de-
signer does not need to enter Hardware Descrip-
tion Language (HDL) equations, unless desired, to
define PSD8XXFX pin functions and memory map
information. The general design flow is shown in
Figure 4. PSDsoft Express is available from our
web site (the address is given on the back page of
this data sheet) or other distribution channels.
PSDsoft Express directly supports two low cost
device programmers form ST: PSDpro and
FlashLINK (JTAG). Both of these programmers
may be purchased through your local distributor/
representative, or directly from our web site using
a credit card. The PSD8XXFX is also supported by
third party device programmers. See our web site
for the current list.
Figure 4. PSDsoft Express Development Tool
PSDabel
PLD DESCRIPTION
MODIFY ABEL TEMPLATE FILE
OR GENERATE NEW FILE
PSD Configuration
PSD TOOLS
CONFIGURE MCU BUS
INTERFACE AND OTHER
PSD ATTRIBUTES
GENERATE C CODE
SPECIFIC TO PSD
FUNCTIONS
PSD Fitter
USER'S CHOICE OF
FIRMWARE
LOGIC SYNTHESIS
AND FITTING
MICROCONTROLLER
HEX OR S-RECORD
FORMAT
COMPILER/LINKER
ADDRESS TRANSLATION
AND MEMORY MAPPING
*.OBJ FILE
PSD Simulator
PSD Programmer
*.OBJ AND *.SVF
FILES AVAILABLE
FOR 3rd PARTY
PROGRAMMERS
(CONVENTIONAL or
JTAG-ISC)
PSDsilos III
DEVICE SIMULATION
(OPTIONAL)
PSDPro, or
FlashLINK (JTAG)
AI04918
13/103
PSD81XFX, PSD83XF2, PSD85XF2
PIN DESCRIPTION
Table 5 describes the signal names and signal
functions of the PSD8XXFX.
Table 5. Pin Description (for the PLCC52 package - Note 1)
Pin Name
Pin
Type
Description
This is the lower Address/Data port. Connect your MCU address or address/data bus
according to the following rules:
1. If your MCU has a multiplexed address/data bus where the data is multiplexed with the
lower address bits, connect AD0-AD7 to this port.
2. If your MCU does not have a multiplexed address/data bus, or you are using an
80C251 in page mode, connect A0-A7 to this port.
ADIO0-7
30-37 I/O
3. If you are using an 80C51XA in burst mode, connect A4/D0 through A11/D7 to this
port.
ALE or AS latches the address. The PSD8XXFX drives data out only if the READ signal is
active and one of the PSD8XXFX functional blocks was selected. The addresses on this
port are passed to the PLDs.
This is the upper Address/Data port. Connect your MCU address or address/data bus
according to the following rules:
1. If your MCU has a multiplexed address/data bus where the data is multiplexed with the
lower address bits, connect A8-A15 to this port.
2. If your MCU does not have a multiplexed address/data bus, connect A8-A15 to this
port.
3. If you are using an 80C251 in page mode, connect AD8-AD15 to this port.
4. If you are using an 80C51XA in burst mode, connect A12/D8 through A19/D15 to this
port.
ADIO8-15 39-46 I/O
ALE or AS latches the address. The PSD8XXFX drives data out only if the READ signal is
active and one of the PSD8XXFX functional blocks was selected. The addresses on this
port are passed to the PLDs.
The following control signals can be connected to this port, based on your MCU:
1. WR – active Low Write Strobe input.
CNTL0
CNTL1
47
50
I
I
2. R_W – active High READ/active Low write input.
This port is connected to the PLDs. Therefore, these signals can be used in decode and
other logic equations.
The following control signals can be connected to this port, based on your MCU:
1. RD – active Low Read Strobe input.
2. E – E clock input.
3. DS – active Low Data Strobe input.
4. PSEN – connect PSEN to this port when it is being used as an active Low READ
signal. For example, when the 80C251 outputs more than 16 address bits, PSEN is
actually the READ signal.
This port is connected to the PLDs. Therefore, these signals can be used in decode and
other logic equations.
This port can be used to input the PSEN (Program Select Enable) signal from any MCU
that uses this signal for code exclusively. If your MCU does not output a Program Select
Enable signal, this port can be used as a generic input. This port is connected to the
PLDs.
CNTL2
Reset
49
48
I
I
Resets I/O Ports, PLD macrocells and some of the Configuration Registers. Must be Low
at Power-up.
14/103
PSD81XFX, PSD83XF2, PSD85XF2
Pin Name
Pin
Type
Description
These pins make up Port A. These port pins are configurable and can have the following
functions:
1. MCU I/O – write to or read from a standard output or input port.
2. CPLD macrocell (McellAB0-7) outputs.
3. Inputs to the PLDs.
4. Latched address outputs (see Table 6).
5. Address inputs. For example, PA0-3 could be used for A0-A3 when using an 80C51XA
in burst mode.
6. As the data bus inputs D0-D7 for non-multiplexed address/data bus MCUs.
7. D0/A16-D3/A19 in M37702M2 mode.
8. Peripheral I/O mode.
PA0
PA1
PA2
PA3
PA4
PA5
PA6
PA7
29
28
27
25
24
23
22
21
I/O
Note: PA0-PA3 can only output CMOS signals with an option for high slew rate. However,
PA4-PA7 can be configured as CMOS or Open Drain Outputs.
PB0
PB1
PB2
PB3
PB4
PB5
PB6
PB7
7
6
5
4
3
2
52
51
These pins make up Port B. These port pins are configurable and can have the following
functions:
1. MCU I/O – write to or read from a standard output or input port.
2. CPLD macrocell (McellAB0-7 or McellBC0-7) outputs.
3. Inputs to the PLDs.
4. Latched address outputs (see Table 6).
Note: PB0-PB3 can only output CMOS signals with an option for high slew rate. However,
PB4-PB7 can be configured as CMOS or Open Drain Outputs.
I/O
PC0 pin of Port C. This port pin can be configured to have the following functions:
1. MCU I/O – write to or read from a standard output or input port.
2. CPLD macrocell (McellBC0) output.
PC0
PC1
PC2
20
19
18
I/O
I/O
I/O
3. Input to the PLDs.
2
4. TMS Input for the JTAG Serial Interface.
This pin can be configured as a CMOS or Open Drain output.
PC1 pin of Port C. This port pin can be configured to have the following functions:
1. MCU I/O – write to or read from a standard output or input port.
2. CPLD macrocell (McellBC1) output.
3. Input to the PLDs.
2
4. TCK Input for the JTAG Serial Interface.
This pin can be configured as a CMOS or Open Drain output.
PC2 pin of Port C. This port pin can be configured to have the following functions:
1. MCU I/O – write to or read from a standard output or input port.
2. CPLD macrocell (McellBC2) output.
3. Input to the PLDs.
4. V
– SRAM stand-by voltage input for SRAM battery backup.
STBY
This pin can be configured as a CMOS or Open Drain output.
PC3 pin of Port C. This port pin can be configured to have the following functions:
1. MCU I/O – write to or read from a standard output or input port.
2. CPLD macrocell (McellBC3) output.
3. Input to the PLDs.
PC3
PC4
17
14
I/O
I/O
2
4. TSTAT output for the JTAG Serial Interface.
5. Ready/Busy output for parallel In-System Programming (ISP).
This pin can be configured as a CMOS or Open Drain output.
PC4 pin of Port C. This port pin can be configured to have the following functions:
1. MCU I/O – write to or read from a standard output or input port.
2. CPLD macrocell (McellBC4) output.
3. Input to the PLDs.
2
4. TERR output for the JTAG Serial Interface.
5. Battery-on Indicator (VBATON). Goes High when power is being drawn from the
external battery.
This pin can be configured as a CMOS or Open Drain output.
15/103
PSD81XFX, PSD83XF2, PSD85XF2
Pin Name
Pin
Type
Description
PC5 pin of Port C. This port pin can be configured to have the following functions:
1. MCU I/O – write to or read from a standard output or input port.
2. CPLD macrocell (McellBC5) output.
PC5
13
I/O
3. Input to the PLDs.
2
4. TDI input for the JTAG Serial Interface.
This pin can be configured as a CMOS or Open Drain output.
PC6 pin of Port C. This port pin can be configured to have the following functions:
1. MCU I/O – write to or read from a standard output or input port.
2. CPLD macrocell (McellBC6) output.
PC6
12
I/O
3. Input to the PLDs.
2
4. TDO output for the JTAG Serial Interface.
This pin can be configured as a CMOS or Open Drain output.
PC7 pin of Port C. This port pin can be configured to have the following functions:
1. MCU I/O – write to or read from a standard output or input port.
2. CPLD macrocell (McellBC7) output.
3. Input to the PLDs.
4. DBE – active Low Data Byte Enable input from 68HC912 type MCUs.
PC7
PD0
PD1
11
10
9
I/O
I/O
I/O
This pin can be configured as a CMOS or Open Drain output.
PD0 pin of Port D. This port pin can be configured to have the following functions:
1. ALE/AS input latches address output from the MCU.
2. MCU I/O – write or read from a standard output or input port.
3. Input to the PLDs.
4. CPLD output (External Chip Select).
PD1 pin of Port D. This port pin can be configured to have the following functions:
1. MCU I/O – write to or read from a standard output or input port.
2. Input to the PLDs.
3. CPLD output (External Chip Select).
4. CLKIN – clock input to the CPLD macrocells, the APD Unit’s Power-down counter, and
the CPLD AND Array.
PD2 pin of Port D. This port pin can be configured to have the following functions:
1. MCU I/O – write to or read from a standard output or input port.
2. Input to the PLDs.
PD2
8
I/O
3. CPLD output (External Chip Select).
4. PSD Chip Select Input (CSI). When Low, the MCU can access the PSD8XXFX
memory and I/O. When High, the PSD8XXFX memory blocks are disabled to conserve
power.
V
15, 38
Supply Voltage
Ground pins
CC
1, 16,
26
GND
Note: 1. The pin numbers in this table are for the PLCC package only. See the package information, on page 98 onwards, for pin numbers
on other package types.
2. These functions can be multiplexed with other functions.
PSD8XXFX REGISTER DESCRIPTION AND ADDRESS OFFSET
Table 7 shows the offset addresses to the
PSD8XXFX registers relative to the CSIOP base
address. The CSIOP space is the 256 bytes of ad-
dress that is allocated by the user to the internal
PSD8XXFX registers. Table 7 provides brief de-
scriptions of the registers in CSIOP space. The fol-
lowing section gives a more detailed description.
16/103
PSD81XFX, PSD83XF2, PSD85XF2
Table 6. I/O Port Latched Address Output Assignments (Note1)
Port A
Port B
MCU
Port A (3:0)
Port A (7:4)
Port B (3:0)
Address a11-a8
Address a11-a8
Address a3-a0
Address a3-a0
Port B (7:4)
8051XA (8-bit)
N/A
N/A
Address a7-a4
N/A
N/A
80C251 (page mode)
Address a15-a12
Address a7-a4
Address a7-a4
All other 8-bit multiplexed
8-bit non-multiplexed bus
Address a3-a0
N/A
Address a7-a4
N/A
Note: 1. See the section entitled “I/O PORTS”, on page 48, on how to enable the Latched Address Output function.
2. N/A = Not Applicable
Table 7. Register Address Offset
1
Register Name
Data In
Port A Port B Port C Port D
Description
Other
00
02
01
03
10
11
Reads Port pin as input, MCU I/O input mode
Selects mode between MCU I/O or Address Out
Control
Stores data for output to Port pins, MCU I/O output
mode
Data Out
Direction
04
06
05
07
12
14
13
15
Configures Port pin as input or output
Configures Port pins as either CMOS or Open
Drain on some pins, while selecting high slew rate
on other pins.
Drive Select
08
09
16
17
Input Macrocell
Enable Out
0A
0C
0B
0D
18
1A
Reads Input Macrocells
Reads the status of the output enable to the I/O
Port driver
1B
Output Macrocells
AB
READ – reads output of macrocells AB
WRITE – loads macrocell flip-flops
20
20
21
Output Macrocells
BC
READ – reads output of macrocells BC
WRITE – loads macrocell flip-flops
21
23
Mask Macrocells AB 22
Mask Macrocells BC
22
23
Blocks writing to the Output Macrocells AB
Blocks writing to the Output Macrocells BC
Primary Flash
Protection
C0
C2
Read only – Primary Flash Sector Protection
Secondary Flash
memory Protection
Read only – PSD8XXFX Security and Secondary
Flash memory Sector Protection
JTAG Enable
PMMR0
PMMR2
Page
C7
B0
B4
E0
Enables JTAG Port
Power Management Register 0
Power Management Register 2
Page Register
Places PSD8XXFX memory areas in Program
and/or Data space on an individual basis.
VM
E2
Note: 1. Other registers that are not part of the I/O ports.
17/103
PSD81XFX, PSD83XF2, PSD85XF2
DETAILED OPERATION
As shown in Figure 3, the PSD8XXFX consists of
six major types of functional blocks:
(FS0-FS7) which can contain up to three product
terms. Each of the four sectors of the secondary
Flash memory has a Select signal (CSBOOT0-
CSBOOT3) which can contain up to three product
terms. Having three product terms for each Select
signal allows a given sector to be mapped in differ-
ent areas of system memory. When using a MCU
with separate Program and Data space, these
flexible Select signals allow dynamic re-mapping
of sectors from one memory space to the other.
Ready/Busy (PC3). This signal can be used to
output the Ready/Busy status of the PSD8XXFX.
The output on Ready/Busy (PC3) is a 0 (Busy)
when Flash memory is being written to, or when
Flash memory is being erased. The output is a 1
(Ready) when no WRITE or Erase cycle is in
progress.
■ Memory Blocks
■ PLD Blocks
■ MCU Bus Interface
■ I/O Ports
■ Power Management Unit (PMU)
■ JTAG Interface
The functions of each block are described in the
following sections. Many of the blocks perform
multiple functions, and are user configurable.
MEMORY BLOCKS
The PSD8XXFX has the following memory blocks:
– Primary Flash memory
– Optional Secondary Flash memory
– Optional SRAM
Memory Operation. The primary Flash memory
and secondary Flash memory are addressed
through the MCU Bus Interface. The MCU can ac-
cess these memories in one of two ways:
■ The MCU can execute a typical bus WRITE or
READ operation just as it would if accessing a
RAM or ROM device using standard bus cycles.
The Memory Select signals for these blocks origi-
nate from the Decode PLD (DPLD) and are user-
defined in PSDsoft Express.
■ The MCU can execute a specific instruction that
consists of several WRITE and READ
Primary Flash Memory and Secondary Flash
memory Description
The primary Flash memory is divided evenly into
eight equal sectors. The secondary Flash memory
is divided into four equal sectors. Each sector of
either memory block can be separately protected
from Program and Erase cycles.
operations. This involves writing specific data
patterns to special addresses within the Flash
memory to invoke an embedded algorithm.
These instructions are summarized in Table 8.
Typically, the MCU can read Flash memory using
READ operations, just as it would read a ROM de-
vice. However, Flash memory can only be altered
using specific Erase and Program instructions. For
example, the MCU cannot write a single byte di-
rectly to Flash memory as it would write a byte to
RAM. To program a byte into Flash memory, the
MCU must execute a Program instruction, then
test the status of the Program cycle. This status
test is achieved by a READ operation or polling
Ready/Busy (PC3).
Flash memory may be erased on a sector-by-sec-
tor basis. Flash sector erasure may be suspended
while data is read from other sectors of the block
and then resumed after reading.
During a Program or Erase cycle in Flash memory,
the status can be output on Ready/Busy (PC3).
This pin is set up using PSDsoft Express Configu-
ration.
Memory Block Select Signals
Flash memory can also be read by using special
instructions to retrieve particular Flash device in-
formation (sector protect status and ID).
The DPLD generates the Select signals for all the
internal memory blocks (see the section entitled
“PLDS”, on page 30). Each of the eight sectors of
the primary Flash memory has a Select signal
18/103
PSD81XFX, PSD83XF2, PSD85XF2
Table 8. Instructions
FS0-FS7 or
CSBOOT0-
CSBOOT3
Cycle 1
Cycle 2 Cycle 3
Cycle 4
Cycle 5 Cycle 6 Cycle 7
Instruction
“READ”
RD @ RA
5
1
1
1
1
1
1
1
READ
Read Main
AAh@
X555h
55h@
XAAAh
90h@
X555h
Read identifier
(A6,A1,A0 = 0,0,1)
6
Flash ID
Read Sector
AAh@
X555h
55h@
XAAAh
90h@
X555h
Read identifier
(A6,A1,A0 = 0,1,0)
6,8,13
Protection
Program a
Flash Byte
AAh@
X555h
55h@
XAAAh
A0h@
X555h
PD@ PA
13
7
Flash Sector
AAh@
X555h
55h@
XAAAh
80h@
X555h
55h@
XAAAh
30h@
SA
30h @
AAh@ X555h
AAh@ X555h
7,13
Erase
next SA
Flash Bulk
AAh@
X555h
55h@
XAAAh
80h@
X555h
55h@
XAAAh
10h@
X555h
13
Erase
Suspend
B0h@
XXXXh
11
12
Sector Erase
Resume
30h@
XXXXh
1
1
1
1
Sector Erase
F0h@
XXXXh
6
Reset
AAh@
X555h
55h@
XAAAh
20h@
X555h
Unlock Bypass
Unlock Bypass
A0h@
XXXXh
PD@ PA
9
Program
Unlock Bypass
90h@
XXXXh
00h@
XXXXh
1
10
Reset
Note: 1. All bus cycles are WRITE bus cycles, except the ones with the “READ” label
2. All values are in hexadecimal:
X = Don’t Care. Addresses of the form XXXXh, in this table, must be even addresses
RA = Address of the memory location to be read
RD = Data read from location RA during the READ cycle
PA = Address of the memory location to be programmed. Addresses are latched on the falling edge of Write Strobe (WR, CNTL0).
PA is an even address for PSD in word programming mode.
PD = Data word to be programmed at location PA. Data is latched on the rising edge of Write Strobe (WR, CNTL0)
SA = Address of the sector to be erased or verified. The Sector Select (FS0-FS7 or CSBOOT0-CSBOOT3) of the sector to be
erased, or verified, must be Active (High).
3. Sector Select (FS0 to FS7 or CSBOOT0 to CSBOOT3) signals are active High, and are defined in PSDsoft Express.
4. Only address bits A11-A0 are used in instruction decoding.
5. No Unlock or instruction cycles are required when the device is in the READ Mode
6. The Reset instruction is required to return to the READ Mode after reading the Flash ID, or after reading the Sector Protection Sta-
tus, or if the Error Flag (DQ5/DQ13) bit goes High.
7. Additional sectors to be erased must be written at the end of the Sector Erase instruction within 80µs.
8. The data is 00h for an unprotected sector, and 01h for a protected sector. In the fourth cycle, the Sector Select is active, and
(A1,A0)=(1,0)
9. The Unlock Bypass instruction is required prior to the Unlock Bypass Program instruction.
10. The Unlock Bypass Reset Flash instruction is required to return to reading memory data when the device is in the Unlock Bypass
mode.
11. The system may perform READ and Program cycles in non-erasing sectors, read the Flash ID or read the Sector Protection Status
when in the Suspend Sector Erase mode. The Suspend Sector Erase instruction is valid only during a Sector Erase cycle.
12. The Resume Sector Erase instruction is valid only during the Suspend Sector Erase mode.
13. The MCU cannot invoke these instructions while executing code from the same Flash memory as that for which the instruction is
intended. The MCU must fetch, for example, the code from the secondary Flash memory when reading the Sector Protection Status
of the primary Flash memory.
19/103
PSD81XFX, PSD83XF2, PSD85XF2
INSTRUCTIONS
An instruction consists of a sequence of specific
operations. Each received byte is sequentially de-
coded by the PSD8XXFX and not executed as a
standard WRITE operation. The instruction is exe-
cuted when the correct number of bytes are prop-
erly received and the time between two
consecutive bytes is shorter than the time-out pe-
riod. Some instructions are structured to include
READ operations after the initial WRITE opera-
tions.
The instruction must be followed exactly. Any in-
valid combination of instruction bytes or time-out
between two consecutive bytes while addressing
Flash memory resets the device logic into READ
Mode (Flash memory is read like a ROM device).
The PSD8XXFX supports the instructions summa-
rized in Table 8:
Flash memory:
■ Erase memory by chip or sector
■ Suspend or resume sector erase
■ Program a Byte
must be held Low, and Write Strobe (WR, CNTL0)
High, during Power-up for maximum security of
the data contents and to remove the possibility of
a byte being written on the first edge of Write
Strobe (WR, CNTL0). Any WRITE cycle initiation
is locked when V is below V
.
CC
LKO
READ
Under typical conditions, the MCU may read the
primary Flash memory or the secondary Flash
memory using READ operations just as it would a
ROM or RAM device. Alternately, the MCU may
use READ operations to obtain status information
about a Program or Erase cycle that is currently in
progress. Lastly, the MCU may use instructions to
read special data from these memory blocks. The
following sections describe these READ functions.
Read Memory Contents. Primary Flash memory
and secondary Flash memory are placed in the
READ Mode after Power-up, chip reset, or a Reset
Flash instruction (see Table 8). The MCU can read
the memory contents of the primary Flash memory
or the secondary Flash memory by using READ
operations any time the READ operation is not
part of an instruction.
■ Reset to READ Mode
■ Read primary Flash Identifier value
■ Read Sector Protection Status
Read Primary Flash Identifier. The
primary
Flash memory identifier is read with an instruction
composed of 4 operations: 3 specific WRITE oper-
ations and a READ operation (see Table 8). Dur-
ing the READ operation, address bits A6, A1, and
A0 must be 0,0,1, respectively, and the appropri-
ate Sector Select (FS0-FS7) must be High. The
identifier for the PSD813F2/3/4/5 is E4h, and for
the PSD83xF2 or PSD85xF2 it is E7h.
Read Memory Sector Protection Status. The
primary Flash memory Sector Protection Status is
read with an instruction composed of 4 operations:
3 specific WRITE operations and a READ opera-
tion (see Table 8). During the READ operation, ad-
dress bits A6, A1, and A0 must be 0,1,0,
respectively, while Sector Select (FS0-FS7 or
CSBOOT0-CSBOOT3) designates the Flash
memory sector whose protection has to be veri-
fied. The READ operation produces 01h if the
Flash memory sector is protected, or 00h if the
sector is not protected.
■ Bypass (on the PSD833F2, PSD834F2,
PSD853F2 and PSD854F2)
These instructions are detailed in Table 8. For ef-
ficient decoding of the instructions, the first two
bytes of an instruction are the coded cycles and
are followed by an instruction byte or confirmation
byte. The coded cycles consist of writing the data
AAh to address X555h during the first cycle and
data 55h to address XAAAh during the second cy-
cle. Address signals A15-A12 are Don’t Care dur-
ing the instruction WRITE cycles. However, the
appropriate
Sector
Select
(FS0-FS7
or
CSBOOT0-CSBOOT3) must be selected.
The primary and secondary Flash memories have
the same instruction set (except for Read Primary
Flash Identifier). The Sector Select signals deter-
mine which Flash memory is to receive and exe-
cute the instruction. The primary Flash memory is
selected if any one of Sector Select (FS0-FS7) is
High, and the secondary Flash memory is selected
if any one of Sector Select (CSBOOT0-
CSBOOT3) is High.
The sector protection status for all NVM blocks
(primary Flash memory or secondary Flash mem-
ory) can also be read by the MCU accessing the
Flash Protection registers in PSD I/O space. See
the section entitled “Flash Memory Sector Pro-
tect”, on page 25, for register definitions.
Power-down Instruction and Power-up Mode
Power-up Mode. The PSD8XXFX internal logic
is reset upon Power-up to the READ Mode. Sector
Select (FS0-FS7 and CSBOOT0-CSBOOT3)
20/103
PSD81XFX, PSD83XF2, PSD85XF2
Reading the Erase/Program Status Bits. The
PSD8XXFX provides several status bits to be
used by the MCU to confirm the completion of an
Erase or Program cycle of Flash memory. These
status bits minimize the time that the MCU spends
performing these tasks and are defined in Table 9.
The status bits can be read as many times as
needed.
For Flash memory, the MCU can perform a READ
operation to obtain these status bits while an
Erase or Program instruction is being executed by
the embedded algorithm. See the section entitled
“Programming Flash Memory”, on page 22, for de-
tails.
Data Polling Flag (DQ7). When erasing or pro-
gramming in Flash memory, the Data Polling Flag
(DQ7) bit outputs the complement of the bit being
entered for programming/writing on the DQ7 bit.
Once the Program instruction or the WRITE oper-
ation is completed, the true logic value is read on
the Data Polling Flag (DQ7) bit (in a READ opera-
tion).
When the internal cycle is complete, the toggling
stops and the data read on the Data Bus D0-D7 is
the addressed memory byte. The device is now
accessible for a new READ or WRITE operation.
The cycle is finished when two successive READs
yield the same output data.
■ The Toggle Flag (DQ6) bit is effective after the
fourth WRITE pulse (for a Program instruction)
or after the sixth WRITE pulse (for an Erase
instruction).
■ If the byte to be programmed belongs to a
protected Flash memory sector, the instruction
is ignored.
■ If all the Flash memory sectors selected for
erasure are protected, the Toggle Flag (DQ6) bit
toggles to 0 for about 100µs and then returns to
the previous addressed byte.
Error Flag (DQ5). During a normal Program or
Erase cycle, the Error Flag (DQ5) bit is to 0. This
bit is set to 1 when there is a failure during Flash
memory Byte Program, Sector Erase, or Bulk
Erase cycle.
■ Data Polling is effective after the fourth WRITE
pulse (for a Program instruction) or after the
sixth WRITE pulse (for an Erase instruction). It
must be performed at the address being
programmed or at an address within the Flash
memory sector being erased.
■ During an Erase cycle, the Data Polling Flag
(DQ7) bit outputs a 0. After completion of the
cycle, the Data Polling Flag (DQ7) bit outputs
the last bit programmed (it is a 1 after erasing).
In the case of Flash memory programming, the Er-
ror Flag (DQ5) bit indicates the attempt to program
a Flash memory bit from the programmed state, 0,
to the erased state, 1, which is not valid. The Error
Flag (DQ5) bit may also indicate a Time-out condi-
tion while attempting to program a byte.
In case of an error in a Flash memory Sector Erase
or Byte Program cycle, the Flash memory sector in
which the error occurred or to which the pro-
grammed byte belongs must no longer be used.
Other Flash memory sectors may still be used.
The Error Flag (DQ5) bit is reset after a Reset
Flash instruction.
Erase Time-out Flag (DQ3). The Erase Time-
out Flag (DQ3) bit reflects the time-out period al-
lowed between two consecutive Sector Erase in-
structions. The Erase Time-out Flag (DQ3) bit is
reset to 0 after a Sector Erase cycle for a time pe-
riod of 100µs + 20% unless an additional Sector
Erase instruction is decoded. After this time peri-
od, or when the additional Sector Erase instruction
is decoded, the Erase Time-out Flag (DQ3) bit is
set to 1.
■ If the byte to be programmed is in a protected
Flash memory sector, the instruction is ignored.
■ If all the Flash memory sectors to be erased are
protected, the Data Polling Flag (DQ7) bit is
reset to 0 for about 100µs, and then returns to
the previous addressed byte. No erasure is
performed.
Toggle Flag (DQ6). The PSD8XXFX offers an-
other way for determining when the Flash memory
Program cycle is completed. During the internal
WRITE operation and when either the FS0-FS7 or
CSBOOT0-CSBOOT3 is true, the Toggle Flag
(DQ6) bit toggles from 0 to 1 and 1 to 0 on subse-
quent attempts to read any byte of the memory.
Table 9. Status Bit
FS0-FS7/CSBOOT0-
Functional Block
DQ7
DQ6
DQ5
DQ4
DQ3
DQ2
DQ1
DQ0
CSBOOT3
Erase
Time-
out
Data
Polling Flag
Toggle Error
Flag
V
Flash Memory
X
X
X
X
IH
Note: 1. X = Not guaranteed value, can be read either 1 or 0.
2. DQ7-DQ0 represent the Data Bus bits, D7-D0.
3. FS0-FS7 and CSBOOT0-CSBOOT3 are active High.
21/103
PSD81XFX, PSD83XF2, PSD85XF2
Programming Flash Memory
Flash memory must be erased prior to being pro-
grammed. A byte of Flash memory is erased to all
1s (FFh), and is programmed by setting selected
bits to 0. The MCU may erase Flash memory all at
once or by-sector, but not byte-by-byte. However,
the MCU may program Flash memory byte-by-
byte.
The primary and secondary Flash memories re-
quire the MCU to send an instruction to program a
byte or to erase sectors (see Table 8).
Once the MCU issues a Flash memory Program or
Erase instruction, it must check for the status bits
for completion. The embedded algorithms that are
invoked inside the PSD8XXFX support several
means to provide status to the MCU. Status may
be checked using any of three methods: Data Poll-
ing, Data Toggle, or Ready/Busy (PC3).
ming algorithm has completed, to compare the
byte that was written to the Flash memory with the
byte that was intended to be written.
When using the Data Polling method during an
Erase cycle, Figure 5 still applies. However, the
Data Polling Flag (DQ7) bit is 0 until the Erase cy-
cle is complete. A 1 on the Error Flag (DQ5) bit in-
dicates a time-out condition on the Erase cycle; a
0 indicates no error. The MCU can read any loca-
tion within the sector being erased to get the Data
Polling Flag (DQ7) bit and the Error Flag (DQ5) bit.
PSDsoft Express generates ANSI C code func-
tions which implement these Data Polling algo-
rithms.
Figure 5. Data Polling Flowchart
Data Polling. Polling on the Data Polling Flag
(DQ7) bit is a method of checking whether a Pro-
gram or Erase cycle is in progress or has complet-
ed. Figure 5 shows the Data Polling algorithm.
START
READ DQ5 & DQ7
at VALID ADDRESS
When the MCU issues a Program instruction, the
embedded algorithm within the PSD8XXFX be-
gins. The MCU then reads the location of the byte
to be programmed in Flash memory to check sta-
tus. The Data Polling Flag (DQ7) bit of this location
becomes the complement of b7 of the original data
byte to be programmed. The MCU continues to
poll this location, comparing the Data Polling Flag
(DQ7) bit and monitoring the Error Flag (DQ5) bit.
When the Data Polling Flag (DQ7) bit matches b7
of the original data, and the Error Flag (DQ5) bit
remains 0, the embedded algorithm is complete. If
the Error Flag (DQ5) bit is 1, the MCU should test
the Data Polling Flag (DQ7) bit again since the
Data Polling Flag (DQ7) bit may have changed si-
multaneously with the Error Flag (DQ5) bit (see
Figure 5).
DQ7
=
YES
DATA
NO
NO
DQ5
= 1
YES
READ DQ7
DQ7
=
DATA
YES
The Error Flag (DQ5) bit is set if either an internal
time-out occurred while the embedded algorithm
attempted to program the byte or if the MCU at-
tempted to program a 1 to a bit that was not erased
(not erased is logic 0).
NO
FAIL
PASS
AI01369B
It is suggested (as with all Flash memories) to read
the location again after the embedded program-
22/103
PSD81XFX, PSD83XF2, PSD85XF2
Data Toggle. Checking the Toggle Flag (DQ6) bit
is a method of determining whether a Program or
Erase cycle is in progress or has completed. Fig-
ure 6 shows the Data Toggle algorithm.
The Error Flag (DQ5) bit is set if either an internal
time-out occurred while the embedded algorithm
attempted to program the byte, or if the MCU at-
tempted to program a 1 to a bit that was not erased
(not erased is logic 0).
When the MCU issues a Program instruction, the
embedded algorithm within the PSD8XXFX be-
gins. The MCU then reads the location of the byte
to be programmed in Flash memory to check sta-
tus. The Toggle Flag (DQ6) bit of this location tog-
gles each time the MCU reads this location until
the embedded algorithm is complete. The MCU
continues to read this location, checking the Tog-
gle Flag (DQ6) bit and monitoring the Error Flag
(DQ5) bit. When the Toggle Flag (DQ6) bit stops
toggling (two consecutive reads yield the same
value), and the Error Flag (DQ5) bit remains 0, the
embedded algorithm is complete. If the Error Flag
(DQ5) bit is 1, the MCU should test the Toggle
Flag (DQ6) bit again, since the Toggle Flag (DQ6)
bit may have changed simultaneously with the Er-
ror Flag (DQ5) bit (see Figure 6).
It is suggested (as with all Flash memories) to read
the location again after the embedded program-
ming algorithm has completed, to compare the
byte that was written to Flash memory with the
byte that was intended to be written.
When using the Data Toggle method after an
Erase cycle, Figure 6 still applies. the Toggle Flag
(DQ6) bit toggles until the Erase cycle is complete.
A 1 on the Error Flag (DQ5) bit indicates a time-out
condition on the Erase cycle; a 0 indicates no er-
ror. The MCU can read any location within the sec-
tor being erased to get the Toggle Flag (DQ6) bit
and the Error Flag (DQ5) bit.
PSDsoft Express generates ANSI C code func-
tions which implement these Data Toggling algo-
rithms.
Unlock Bypass (PSD833F2x, PSD834F2x,
PSD853F2x, PSD854F2x). The Unlock Bypass
instructions allow the system to program bytes to
the Flash memories faster than using the standard
Program instruction. The Unlock Bypass mode is
entered by first initiating two Unlock cycles. This is
followed by a third WRITE cycle containing the Un-
lock Bypass code, 20h (as shown in Table 8).
Figure 6. Data Toggle Flowchart
START
READ
DQ5 & DQ6
The Flash memory then enters the Unlock Bypass
mode. A two-cycle Unlock Bypass Program in-
struction is all that is required to program in this
mode. The first cycle in this instruction contains
the Unlock Bypass Program code, A0h. The sec-
ond cycle contains the program address and data.
Additional data is programmed in the same man-
ner. These instructions dispense with the initial
two Unlock cycles required in the standard Pro-
gram instruction, resulting in faster total Flash
memory programming.
DQ6
NO
=
TOGGLE
YES
NO
DQ5
= 1
YES
READ DQ6
During the Unlock Bypass mode, only the Unlock
Bypass Program and Unlock Bypass Reset Flash
instructions are valid.
To exit the Unlock Bypass mode, the system must
issue the two-cycle Unlock Bypass Reset Flash in-
struction. The first cycle must contain the data
90h; the second cycle the data 00h. Addresses are
Don’t Care for both cycles. The Flash memory
then returns to READ Mode.
DQ6
=
NO
TOGGLE
YES
FAIL
PASS
AI01370B
23/103
PSD81XFX, PSD83XF2, PSD85XF2
Erasing Flash Memory
Flash Bulk Erase. The Flash Bulk Erase instruc-
tion uses six WRITE operations followed by a
READ operation of the status register, as de-
scribed in Table 8. If any byte of the Bulk Erase in-
struction is wrong, the Bulk Erase instruction
aborts and the device is reset to the Read Flash
memory status.
During a Bulk Erase, the memory status may be
checked by reading the Error Flag (DQ5) bit, the
Toggle Flag (DQ6) bit, and the Data Polling Flag
(DQ7) bit, as detailed in the section entitled “Pro-
gramming Flash Memory”, on page 22. The Error
Flag (DQ5) bit returns a 1 if there has been an
Erase Failure (maximum number of Erase cycles
have been executed).
(DQ7) bit, as detailed in the section entitled “Pro-
gramming Flash Memory”, on page 22.
During execution of the Erase cycle, the Flash
memory accepts only Reset and Suspend Sector
Erase instructions. Erasure of one Flash memory
sector may be suspended, in order to read data
from another Flash memory sector, and then re-
sumed.
Suspend Sector Erase. When a Sector Erase
cycle is in progress, the Suspend Sector Erase in-
struction can be used to suspend the cycle by writ-
ing 0B0h to any address when an appropriate
Sector Select (FS0-FS7 or CSBOOT0-CSBOOT3)
is High. (See Table 8). This allows reading of data
from another Flash memory sector after the Erase
cycle has been suspended. Suspend Sector
Erase is accepted only during an Erase cycle and
defaults to READ Mode. A Suspend Sector Erase
instruction executed during an Erase time-out pe-
riod, in addition to suspending the Erase cycle, ter-
minates the time out period.
It is not necessary to program the memory with
00h because the PSD8XXFX automatically does
this before erasing to 0FFh.
During execution of the Bulk Erase instruction, the
Flash memory does not accept any instructions.
Flash Sector Erase. The Sector Erase instruc-
tion uses six WRITE operations, as described in
Table 8. Additional Flash Sector Erase codes and
Flash memory sector addresses can be written
subsequently to erase other Flash memory sec-
tors in parallel, without further coded cycles, if the
additional bytes are transmitted in a shorter time
than the time-out period of about 100µs. The input
of a new Sector Erase code restarts the time-out
period.
The Toggle Flag (DQ6) bit stops toggling when the
PSD8XXFX internal logic is suspended. The sta-
tus of this bit must be monitored at an address
within the Flash memory sector being erased. The
Toggle Flag (DQ6) bit stops toggling between
0.1 µs and 15 µs after the Suspend Sector Erase
instruction has been executed. The PSD8XXFX is
then automatically set to READ Mode.
If an Suspend Sector Erase instruction was exe-
cuted, the following rules apply:
– Attempting to read from a Flash memory sector
that was being erased outputs invalid data.
The status of the internal timer can be monitored
through the level of the Erase Time-out Flag (DQ3)
bit. If the Erase Time-out Flag (DQ3) bit is 0, the
Sector Erase instruction has been received and
the time-out period is counting. If the Erase Time-
out Flag (DQ3) bit is 1, the time-out period has ex-
pired and the PSD8XXFX is busy erasing the
Flash memory sector(s). Before and during Erase
time-out, any instruction other than Suspend Sec-
tor Erase and Resume Sector Erase instructions
abort the cycle that is currently in progress, and re-
set the device to READ Mode. It is not necessary
to program the Flash memory sector with 00h as
the PSD8XXFX does this automatically before
erasing (byte = FFh).
– Reading from a Flash sector that was not being
erased is valid.
– The Flash memory cannot be programmed, and
only responds to Resume Sector Erase and
Reset Flash instructions (READ is an operation
and is allowed).
– If a Reset Flash instruction is received, data in
the Flash memory sector that was being erased
is invalid.
Resume Sector Erase. If
a
Suspend Sector
Erase instruction was previously executed, the
erase cycle may be resumed with this instruction.
The Resume Sector Erase instruction consists of
writing 030h to any address while an appropriate
Sector Select (FS0-FS7 or CSBOOT0-CSBOOT3)
is High. (See Table 8.)
During a Sector Erase, the memory status may be
checked by reading the Error Flag (DQ5) bit, the
Toggle Flag (DQ6) bit, and the Data Polling Flag
24/103
PSD81XFX, PSD83XF2, PSD85XF2
Specific Features
Flash Memory Sector Protect. Each
primary
contents using the JTAG Port or a Device Pro-
grammer. The MCU can read (but cannot change)
the sector protection bits.
Any attempt to program or erase a protected Flash
memory sector is ignored by the device. The Verify
operation results in a READ of the protected data.
This allows a guarantee of the retention of the Pro-
tection status.
The sector protection status can be read by the
MCU through the Flash memory protection and
PSD/EE protection registers (in the CSIOP block).
See Table 10 and Table 11.
and secondary Flash memory sector can be sepa-
rately protected against Program and Erase cy-
cles. Sector Protection provides additional data
security because it disables all Program or Erase
cycles. This mode can be activated through the
JTAG Port or a Device Programmer.
Sector protection can be selected for each sector
using the PSDsoft Express Configuration pro-
gram. This automatically protects selected sectors
when the device is programmed through the JTAG
Port or a Device Programmer. Flash memory sec-
tors can be unprotected to allow updating of their
Table 10. Sector Protection/Security Bit Definition – Flash Protection Register
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
Sec7_Prot
Sec6_Prot
Sec5_Prot
Sec4_Prot
Sec3_Prot
Sec2_Prot
Sec1_Prot
Sec0_Prot
Note: 1. Bit Definitions:
Sec<i>_Prot 1 = Primary Flash memory or secondary Flash memory Sector <i> is write protected.
Sec<i>_Prot 0 = Primary Flash memory or secondary Flash memory Sector <i> is not write protected.
Table 11. Sector Protection/Security Bit Definition – PSD/EE Protection Register
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
Security_Bit not used
Note: 1. Bit Definitions:
not used
not used
Sec3_Prot
Sec2_Prot
Sec1_Prot
Sec0_Prot
Sec<i>_Prot 1 = Secondary Flash memory Sector <i> is write protected.
Sec<i>_Prot 0 = Secondary Flash memory Sector <i> is not write protected.
Security_Bit 0 = Security Bit in device has not been set.
1 = Security Bit in device has been set.
Reset Flash. The Reset Flash instruction con-
sists of one WRITE cycle (see Table 8). It can also
be optionally preceded by the standard two
WRITE decoding cycles (writing AAh to 555h and
55h to AAAh). It must be executed after:
curred (and the device has set the Error Flag
(DQ5) bit to 1) the Flash memory is put back into
normal READ Mode within 25 µs of the Reset
Flash instruction having been issued. The Reset
Flash instruction is ignored when it is issued dur-
ing a Program or Bulk Erase cycle of the Flash
memory. The Reset Flash instruction aborts any
on-going Sector Erase cycle, and returns the
Flash memory to the normal READ Mode within
25 µs.
– Reading the Flash Protection Status or Flash ID
– An Error condition has occurred (and the device
has set the Error Flag (DQ5) bit to 1) during a
Flash memory Program or Erase cycle.
On the PSD813F2/3/4/5, the Reset Flash instruc-
tion puts the Flash memory back into normal
READ Mode. It may take the Flash memory up to
a few milliseconds to complete the Reset cycle.
The Reset Flash instruction is ignored when it is is-
sued during a Program or Bulk Erase cycle of the
Flash memory. The Reset Flash instruction aborts
any on-going Sector Erase cycle, and returns the
Flash memory to the normal READ Mode within a
few milliseconds.
Reset (RESET) Signal (on the PSD83xF2 and
PSD85xF2). A pulse on Reset (RESET) aborts
any cycle that is in progress, and resets the Flash
memory to the READ Mode. When the reset oc-
curs during a Program or Erase cycle, the Flash
memory takes up to 25 µs to return to the READ
Mode. It is recommended that the Reset (RESET)
pulse (except for Power On Reset, as described
on page 63) be at least 25µs so that the Flash
memory is always ready for the MCU to fetch the
bootstrap instructions after the Reset cycle is com-
plete.
On the PSD83xF2 or PSD85xF2, the Reset Flash
instruction puts the Flash memory back into nor-
mal READ Mode. If an Error condition has oc-
25/103
PSD81XFX, PSD83XF2, PSD85XF2
SRAM
The SRAM is enabled when SRAM Select (RS0)
from the DPLD is High. SRAM Select (RS0) can
contain up to two product terms, allowing flexible
memory mapping.
The SRAM can be backed up using an external
battery. The external battery should be connected
overlap, priority is given to the secondary Flash
memory sector.
6. SRAM, I/O, and Peripheral I/O spaces may
overlap any other memory sector. Priority is
given to the SRAM, I/O, or Peripheral I/O.
Example. FS0 is valid when the address is in the
range of 8000h to BFFFh, CSBOOT0 is valid from
8000h to 9FFFh, and RS0 is valid from 8000h to
87FFh. Any address in the range of RS0 always
accesses the SRAM. Any address in the range of
CSBOOT0 greater than 87FFh (and less than
9FFFh) automatically addresses secondary Flash
memory segment 0. Any address greater than
9FFFh accesses the primary Flash memory seg-
ment 0. You can see that half of the primary Flash
memory segment 0 and one-fourth of secondary
Flash memory segment 0 cannot be accessed in
this example. Also note that an equation that de-
fined FS1 to anywhere in the range of 8000h to
BFFFh would not be valid.
to Voltage Stand-by (V
, PC2). If you have an
STBY
external battery connected to the PSD8XXFX, the
contents of the SRAM are retained in the event of
a power loss. The contents of the SRAM are re-
tained so long as the battery voltage remains at
2 V or greater. If the supply voltage falls below the
battery voltage, an internal power switch-over to
the battery occurs.
PC4 can be configured as an output that indicates
when power is being drawn from the external bat-
tery. Battery-on Indicator (VBATON, PC4) is High
with the supply voltage falls below the battery volt-
age and the battery on Voltage Stand-by (V
,
STBY
PC2) is supplying power to the internal SRAM.
SRAM Select (RS0), Voltage Stand-by (V
,
Figure 7 shows the priority levels for all memory
components. Any component on a higher level can
overlap and has priority over any component on a
lower level. Components on the same level must
not overlap. Level one has the highest priority and
level 3 has the lowest.
STBY
PC2) and Battery-on Indicator (VBATON, PC4)
are all configured using PSDsoft Express Configu-
ration.
Sector Select and SRAM Select
Sector Select (FS0-FS7, CSBOOT0-CSBOOT3)
and SRAM Select (RS0) are all outputs of the
DPLD. They are setup by writing equations for
them in PSDabel. The following rules apply to the
equations for these signals:
Figure 7. Priority Level of Memory and I/O
Components
1. Primary Flash memory and secondary Flash
memory Sector Select signals must not be
larger than the physical sector size.
Highest Priority
2. Any primary Flash memory sector must not be
mapped in the same memory space as another
Flash memory sector.
Level 1
SRAM, I/O, or
Peripheral I/O
Level 2
Secondary
Non-Volatile Memory
3. A secondary Flash memory sector must not be
mapped in the same memory space as another
secondary Flash memory sector.
Level 3
4. SRAM, I/O, and Peripheral I/O spaces must not
overlap.
Primary Flash Memory
Lowest Priority
AI02867D
5. A secondary Flash memory sector may overlap
a primary Flash memory sector. In case of
26/103
PSD81XFX, PSD83XF2, PSD85XF2
Memory Select Configuration for MCUs with
Separate Program and Data Spaces. The 8031
and compatible family of MCUs, which includes
the 80C51, 80C151, 80C251, and 80C51XA, have
separate address spaces for Program memory
(selected using Program Select Enable (PSEN,
CNTL2)) and Data memory (selected using Read
Strobe (RD, CNTL1)). Any of the memories within
the PSD8XXFX can reside in either space or both
spaces. This is controlled through manipulation of
the VM register that resides in the CSIOP space.
changed by the MCU so that memory mapping
can be changed on-the-fly.
For example, you may wish to have SRAM and pri-
mary Flash memory in the Data space at Boot-up,
and secondary Flash memory in the Program
space at Boot-up, and later swap the primary and
secondary Flash memories. This is easily done
with the VM register by using PSDsoft Express
Configuration to configure it for Boot-up and hav-
ing the MCU change it when desired. Table 12 de-
scribes the VM Register.
The VM register is set using PSDsoft Express to
have an initial value. It can subsequently be
Table 12. VM Register
Bit 4
Primary
FL_Data
Bit 3
Secondary
EE_Data
Bit 2
Primary
FL_Code
Bit 1
Secondary
EE_Code
Bit 7
PIO_EN
Bit 0
SRAM_Code
Bit 6
Bit 5
0 = RD
can’t
0 = PSEN
can’t
access Secondary access
0 = PSEN
can’t
access
SRAM
0 = RD can’t
0 = PSEN can’t
access Secondary
Flash memory
0 = disable
PIO mode
not used not used access
Flash
memory
Flash memory
Flash
memory
1 = RD
1 = PSEN
access
Flash
1 = RD access
Secondary Flash
memory
1 = PSEN access 1 = PSEN
1= enable
PIO mode
access
not used not used
Flash
Secondary Flash
access
memory
SRAM
memory
memory
Configuration Modes for MCUs with Separate
Program and Data Spaces. Separate Space
Modes. Program space is separated from Data
space. For example, Program Select Enable
(PSEN, CNTL2) is used to access the program
code from the primary Flash memory, while Read
Strobe (RD, CNTL1) is used to access data from
the secondary Flash memory, SRAM and I/O Port
blocks. This configuration requires the VM register
to be set to 0Ch (see Figure 8).
Figure 8. 8031 Memory Modules – Separate Space
Primary
Flash
Secondary
Flash
SRAM
DPLD
RS0
Memory
Memory
CSBOOT0-3
FS0-FS7
CS
CS
OE
CS
OE
OE
PSEN
RD
AI02869C
27/103
PSD81XFX, PSD83XF2, PSD85XF2
Combined Space Modes. The Program and
Data spaces are combined into one memory
space that allows the primary Flash memory, sec-
ondary Flash memory, and SRAM to be accessed
by either Program Select Enable (PSEN, CNTL2)
or Read Strobe (RD, CNTL1). For example, to
configure the primary Flash memory in Combined
space, bits b2 and b4 of the VM register are set to
1 (see Figure 9).
Figure 9. 8031 Memory Modules – Combined Space
Primary
Flash
Secondary
Flash
SRAM
DPLD
RS0
Memory
Memory
RD
CSBOOT0-3
FS0-FS7
CS
CS
OE
CS
OE
OE
VM REG BIT 3
VM REG BIT 4
PSEN
VM REG BIT 1
RD
VM REG BIT 2
VM REG BIT 0
AI02870C
28/103
PSD81XFX, PSD83XF2, PSD85XF2
Page Register
The 8-bit Page Register increases the addressing
capability of the MCU by a factor of up to 256. The
contents of the register can also be read by the
MCU. The outputs of the Page Register (PGR0-
PGR7) are inputs to the DPLD decoder and can be
included in the Sector Select (FS0-FS7,
CSBOOT0-CSBOOT3), and SRAM Select (RS0)
equations.
If memory paging is not needed, or if not all 8 page
register bits are needed for memory paging, then
these bits may be used in the CPLD for general
logic. See Application Note AN1154.
Figure 10 shows the Page Register. The eight flip-
flops in the register are connected to the internal
data bus D0-D7. The MCU can write to or read
from the Page Register. The Page Register can be
accessed at address location CSIOP + E0h.
Figure 10. Page Register
RESET
PGR0
INTERNAL
SELECTS
AND LOGIC
D0
D1
D2
D3
D4
D5
D6
D7
Q0
Q1
Q2
Q3
Q4
Q5
Q6
Q7
PGR1
PGR2
D0 - D7
DPLD
AND
CPLD
PGR3
PGR4
PGR5
PGR6
PGR7
R/W
PAGE
REGISTER
PLD
AI02871B
29/103
PSD81XFX, PSD83XF2, PSD85XF2
PLDS
The PLDs bring programmable logic functionality
to the PSD8XXFX. After specifying the logic for the
PLDs using the PSDabel tool in PSDsoft Express,
the logic is programmed into the device and avail-
able upon Power-up.
Additionally, five bits are available in PMMR2 to
block MCU control signals from entering the PLDs.
This reduces power consumption and can be used
only when these MCU control signals are not used
in PLD logic equations.
The PSD8XXFX contains two PLDs: the Decode
PLD (DPLD), and the Complex PLD (CPLD). The
PLDs are briefly discussed in the next few para-
graphs, and in more detail in the section entitled
“Decode PLD (DPLD)”, on page 32, and the sec-
tion entitled “Complex PLD (CPLD)”, also on page
33. Figure 11 shows the configuration of the PLDs.
The DPLD performs address decoding for Select
signals for internal components, such as memory,
registers, and I/O ports.
The CPLD can be used for logic functions, such as
loadable counters and shift registers, state ma-
chines, and encoding and decoding logic. These
logic functions can be constructed using the 16
Output Macrocells (OMC), 24 Input Macrocells
(IMC), and the AND Array. The CPLD can also be
used to generate External Chip Select (ECS0-
ECS2) signals.
The AND Array is used to form product terms.
These product terms are specified using PSDabel.
An Input Bus consisting of 73 signals is connected
to the PLDs. The signals are shown in Table 13.
Each of the two PLDs has unique characteristics
suited for its applications. They are described in
the following sections.
Table 13. DPLD and CPLD Inputs
Number
Input Source
Input Name
of
Signals
1
A15-A0
16
3
MCU Address Bus
MCU Control Signals
Reset
CNTL2-CNTL0
RST
1
Power-down
PDN
1
Port A Input
Macrocells
PA7-PA0
PB7-PB0
PC7-PC0
8
8
8
Port B Input
Macrocells
Port C Input
Macrocells
The Turbo Bit in PSD8XXFX
Port D Inputs
Page Register
PD2-PD0
3
8
The PLDs in the PSD8XXFX can minimize power
consumption by switching off when inputs remain
unchanged for an extended time of about 70ns.
Resetting the Turbo bit to 0 (Bit 3 of PMMR0) au-
tomatically places the PLDs into standby if no in-
puts are changing. Turning the Turbo mode off
increases propagation delays while reducing pow-
er consumption. See the section entitled “POWER
MANAGEMENT”, on page 58, on how to set the
Turbo bit.
PGR7-PGR0
Macrocell AB
Feedback
MCELLAB.FB7-
FB0
8
8
Macrocell BC
Feedback
MCELLBC.FB7-
FB0
Secondary Flash
memory Program
Status Bit
Ready/Busy
1
Note: 1. The address inputs are A19-A4 in 80C51XA mode.
30/103
PSD81XFX, PSD83XF2, PSD85XF2
Figure 11. PLD Diagram
I / O P O R T S
P L D I N P U T B U S
31/103
PSD81XFX, PSD83XF2, PSD85XF2
Decode PLD (DPLD)
The DPLD, shown in Figure 12, is used for decod-
ing the address for internal and external compo-
nents. The DPLD can be used to generate the
following decode signals:
■ 1 internal SRAM Select (RS0) signal (two
product terms)
■ 1 internal CSIOP Select (PSD Configuration
Register) signal
■ 8 Sector Select (FS0-FS7) signals for the
primary Flash memory (three product terms
each)
■ 4 Sector Select (CSBOOT0-CSBOOT3) signals
for the secondary Flash memory (three product
terms each)
■ 1 JTAG Select signal (enables JTAG on Port C)
■ 2 internal Peripheral Select signals
(Peripheral I/O mode).
Figure 12. DPLD Logic Array
CSBOOT 0
CSBOOT 1
CSBOOT 2
CSBOOT 3
3
3
3
3
(INPUTS)
3
3
3
3
3
3
3
3
FS0
I/O PORTS (PORT A,B,C)
(24)
FS1
FS2
FS3
FS4
FS5
(8)
MCELLAB.FB [7:0] (FEEDBACKS)
MCELLBC.FB [7:0] (FEEDBACKS)
(8)
(8)
8 PRIMARY FLASH
MEMORY SECTOR SELECTS
PGR0 -PGR7
(16)
(3)
[
]
A 15:0
*
[
]
PD 2:0 (ALE,CLKIN,CSI)
PDN (APD OUTPUT)
FS6
FS7
(1)
(3)
(1)
(1)
[
] (
CNTRL 2:0 READ/WRITE CONTROL SIGNALS)
RESET
RS0
2
1
SRAM SELECT
RD_BSY
CSIOP
I/O DECODER
SELECT
PSEL0
1
1
1
PERIPHERAL I/O MODE
SELECT
PSEL1
JTAGSEL
AI02873D
32/103
PSD81XFX, PSD83XF2, PSD85XF2
Complex PLD (CPLD)
The CPLD can be used to implement system logic
functions, such as loadable counters and shift reg-
isters, system mailboxes, handshaking protocols,
state machines, and random logic. The CPLD can
also be used to generate three External Chip Se-
lect (ECS0-ECS2), routed to Port D.
Although External Chip Select (ECS0-ECS2) can
be produced by any Output Macrocell (OMC),
these three External Chip Select (ECS0-ECS2) on
Port D do not consume any Output Macrocells
(OMC).
As shown in Figure 11, the CPLD has the following
blocks:
■ 24 Input Macrocells (IMC)
■ 16 Output Macrocells (OMC)
■ Macrocell Allocator
■ Product Term Allocator
■ AND Array capable of generating up to 137
product terms
■ Four I/O Ports.
Each of the blocks are described in the sections
that follow.
The Input Macrocells (IMC) and Output Macrocells
(OMC) are connected to the PSD8XXFX internal
data bus and can be directly accessed by the
MCU. This enables the MCU software to load data
into the Output Macrocells (OMC) or read data
from both the Input and Output Macrocells (IMC
and OMC).
This feature allows efficient implementation of sys-
tem logic and eliminates the need to connect the
data bus to the AND Array as required in most
standard PLD macrocell architectures.
Figure 13. Macrocell and I/O Port
PRODUCT TERMS
FROM OTHER
MACROCELLS
MCU ADDRESS / DATA BUS
TO OTHER I/O PORTS
CPLD MACROCELLS
I/O PORTS
DATA
LOAD
CONTROL
LATCHED
ADDRESS OUT
PT PRESET
MCU DATA IN
MCU LOAD
PRODUCT TERM
ALLOCATOR
I/O PIN
DATA
D
Q
MUX
WR
UP TO 10
PRODUCT TERMS
MACROCELL
OUT TO
MCU
CPLD OUTPUT
POLARITY
SELECT
PR DI LD
D/T
SELECT
Q
PT
CPLD
OUTPUT
PDR
CLOCK
INPUT
D/T/JK FF
SELECT
COMB.
/REG
SELECT
GLOBAL
CLOCK
MACROCELL
CK
TO
I/O PORT
ALLOC.
CL
CLOCK
SELECT
Q
DIR
REG.
D
WR
PT CLEAR
(
)
PT OUTPUT ENABLE OE
MACROCELL FEEDBACK
I/O PORT INPUT
INPUT MACROCELLS
Q
Q
D
PT INPUT LATCH GATE/CLOCK
D
G
ALE/AS
AI02874
33/103
PSD81XFX, PSD83XF2, PSD85XF2
Output Macrocell (OMC)
Eight of the Output Macrocells (OMC) are con-
nected to Ports A and B pins and are named as
McellAB0-McellAB7. The other eight macrocells
are connected to Ports B and C pins and are
named as McellBC0-McellBC7. If an McellAB out-
put is not assigned to a specific pin in PSDabel,
the Macrocell Allocator block assigns it to either
Port A or B. The same is true for a McellBC output
on Port B or C. Table 14 shows the macrocells and
port assignment.
The Output Macrocell (OMC) architecture is
shown in Figure 14. As shown in the figure, there
are native product terms available from the AND
Array, and borrowed product terms available (if
unused) from other Output Macrocells (OMC). The
polarity of the product term is controlled by the
XOR gate. The Output Macrocell (OMC) can im-
plement either sequential logic, using the flip-flop
element, or combinatorial logic. The multiplexer
selects between the sequential or combinatorial
logic outputs. The multiplexer output can drive a
port pin and has a feedback path to the AND Array
inputs.
The flip-flop in the Output Macrocell (OMC) block
can be configured as a D, T, JK, or SR type in the
PSDabel program. The flip-flop’s clock, preset,
and clear inputs may be driven from a product
term of the AND Array. Alternatively, CLKIN (PD1)
can be used for the clock input to the flip-flop. The
flip-flop is clocked on the rising edge of CLKIN
(PD1). The preset and clear are active High inputs.
Each clear input can use up to two product terms.
Table 14. Output Macrocell Port and Data Bit Assignments
Output
Macrocell
Port
Assignment
Maximum Borrowed
Product Terms
Data Bit for Loading or
Reading
Native Product Terms
McellAB0
McellAB1
McellAB2
McellAB3
McellAB4
McellAB5
McellAB6
McellAB7
McellBC0
McellBC1
McellBC2
McellBC3
McellBC4
McellBC5
McellBC6
McellBC7
Port A0, B0
Port A1, B1
Port A2, B2
Port A3, B3
Port A4, B4
Port A5, B5
Port A6, B6
Port A7, B7
Port B0, C0
Port B1, C1
Port B2, C2
Port B3, C3
Port B4, C4
Port B5, C5
Port B6, C6
Port B7, C7
3
3
3
3
3
3
3
3
4
4
4
4
4
4
4
4
6
6
6
6
6
6
6
6
5
5
5
5
6
6
6
6
D0
D1
D2
D3
D4
D5
D6
D7
D0
D1
D2
D3
D4
D5
D6
D7
34/103
PSD81XFX, PSD83XF2, PSD85XF2
Product Term Allocator
The CPLD has a Product Term Allocator. The PS-
Dabel compiler uses the Product Term Allocator to
borrow and place product terms from one macro-
cell to another. The following list summarizes how
product terms are allocated:
■ McellAB0-McellAB7 all have three native
product terms and may borrow up to six more
■ McellBC0-McellBC3 all have four native product
This is called product term expansion. PSDsoft
Express performs this expansion as needed.
Loading and Reading the Output Macrocells
(OMC). The Output Macrocells (OMC) block oc-
cupies a memory location in the MCU address
space, as defined by the CSIOP block (see the
section entitled “I/O PORTS”, on page 48). The
flip-flops in each of the 16 Output Macrocells
(OMC) can be loaded from the data bus by a MCU.
Loading the Output Macrocells (OMC) with data
from the MCU takes priority over internal func-
tions. As such, the preset, clear, and clock inputs
to the flip-flop can be overridden by the MCU. The
ability to load the flip-flops and read them back is
useful in such applications as loadable counters
and shift registers, mailboxes, and handshaking
protocols.
terms and may borrow up to five more
■ McellBC4-McellBC7 all have four native product
terms and may borrow up to six more.
Each macrocell may only borrow product terms
from certain other macrocells. Product terms al-
ready in use by one macrocell are not available for
another macrocell.
If an equation requires more product terms than
are available to it, then “external” product terms
are required, which consume other Output Macro-
cells (OMC). If external product terms are used,
extra delay is added for the equation that required
the extra product terms.
Data can be loaded to the Output Macrocells
(OMC) on the trailing edge of Write Strobe (WR,
CNTL0) (edge loading) or during the time that
Write Strobe (WR, CNTL0) is active (level load-
ing). The method of loading is specified in PSDsoft
Express Configuration.
35/103
PSD81XFX, PSD83XF2, PSD85XF2
Figure 14. CPLD Output Macrocell
A N D A R R A Y
P L D I N P U T B U S
36/103
PSD81XFX, PSD83XF2, PSD85XF2
The OMC Mask Register. There is one Mask
Register for each of the two groups of eight Output
Macrocells (OMC). The Mask Registers can be
used to block the loading of data to individual Out-
put Macrocells (OMC). The default value for the
Mask Registers is 00h, which allows loading of the
Output Macrocells (OMC). When a given bit in a
Mask Register is set to a 1, the MCU is blocked
from writing to the associated Output Macrocells
(OMC). For example, suppose McellAB0-
McellAB3 are being used for a state machine. You
would not want a MCU write to McellAB to over-
write the state machine registers. Therefore, you
would want to load the Mask Register for McellAB
(Mask Macrocell AB) with the value 0Fh.
onto the PLD input bus. The outputs of the Input
Macrocells (IMC) can be read by the MCU through
the internal data bus.
The enable for the latch and clock for the register
are driven by a multiplexer whose inputs are a
product term from the CPLD AND Array or the
MCU Address Strobe (ALE/AS). Each product
term output is used to latch or clock four Input
Macrocells (IMC). Port inputs 3-0 can be con-
trolled by one product term and 7-4 by another.
Configurations for the Input Macrocells (IMC) are
specified by equations written in PSDabel (see Ap-
plication Note AN1171). Outputs of the Input Mac-
rocells (IMC) can be read by the MCU via the IMC
buffer. See the section entitled “I/O PORTS”, on
page 48.
The Output Enable of the OMC. The
Output
Macrocells (OMC) block can be connected to an I/
O port pin as a PLD output. The output enable of
each port pin driver is controlled by a single prod-
uct term from the AND Array, ORed with the Direc-
tion Register output. The pin is enabled upon
Power-up if no output enable equation is defined
and if the pin is declared as a PLD output in PSD-
soft Express.
If the Output Macrocell (OMC) output is declared
as an internal node and not as a port pin output in
the PSDabel file, the port pin can be used for other
I/O functions. The internal node feedback can be
routed as an input to the AND Array.
Input Macrocells (IMC) can use Address Strobe
(ALE/AS, PD0) to latch address bits higher than
A15. Any latched addresses are routed to the
PLDs as inputs.
Input Macrocells (IMC) are particularly useful with
handshaking communication applications where
two processors pass data back and forth through
a common mailbox. Figure 16 shows a typical con-
figuration where the Master MCU writes to the Port
A Data Out Register. This, in turn, can be read by
the Slave MCU via the activation of the “Slave-
Read” output enable product term.
The Slave can also write to the Port A Input Mac-
rocells (IMC) and the Master can then read the In-
put Macrocells (IMC) directly.
Input Macrocells (IMC)
The CPLD has 24 Input Macrocells (IMC), one for
each pin on Ports A, B, and C. The architecture of
the Input Macrocells (IMC) is shown in Figure 15.
The Input Macrocells (IMC) are individually config-
urable, and can be used as a latch, register, or to
pass incoming Port signals prior to driving them
Note that the “Slave-Read” and “Slave-Wr” signals
are product terms that are derived from the Slave
MCU inputs Read Strobe (RD, CNTL1), Write
Strobe (WR, CNTL0), and Slave_CS.
37/103
PSD81XFX, PSD83XF2, PSD85XF2
Figure 15. Input Macrocell
A N D A R R A Y
P L D I N P U T B U S
38/103
PSD81XFX, PSD83XF2, PSD85XF2
Figure 16. Handshaking Communication Using Input Macrocells
39/103
PSD81XFX, PSD83XF2, PSD85XF2
MCU BUS INTERFACE
The “no-glue logic” MCU Bus Interface block can
be directly connected to most popular MCUs and
their control signals. Key 8-bit MCUs, with their
bus types and control signals, are shown in Table
15. The interface type is specified using the PSD-
soft Express Configuration.
PSD8XXFX Interface to a Multiplexed 8-Bit
Bus. Figure 17 shows an example of a system us-
ing a MCU with an 8-bit multiplexed bus and a
PSD8XXFX. The ADIO port on the PSD8XXFX is
connected directly to the MCU address/data bus.
Address Strobe (ALE/AS, PD0) latches the ad-
dress signals internally. Latched addresses can
be brought out to Port A or B. The PSD8XXFX
drives the ADIO data bus only when one of its in-
ternal resources is accessed and Read Strobe
(RD, CNTL1) is active. Should the system address
bus exceed sixteen bits, Ports A, B, C, or D may
be used as additional address inputs.
Table 15. MCUs and their Control Signals
Data Bus
2
MCU
CNTL0 CNTL1 CNTL2
PC7
ADIO0 PA3-PA0 PA7-PA3
PD0
ALE
Width
1
1
1
8031
8
8
8
8
8
8
8
8
8
8
8
WR
WR
WR
WR
WR
R/W
R/W
WR
R/W
R/W
R/W
RD
RD
PSEN
RD
RD
E
PSEN
PSEN
A0
A4
A0
A0
A0
A0
A0
A0
A0
A0
A0
(Note )
(Note )
(Note )
1
1
80C51XA
80C251
80C251
80198
ALE
ALE
ALE
ALE
AS
A3-A0
(Note )
(Note )
1
1
1
1
(Note ) (Note )
(Note )
(Note )
1
1
1
PSEN
(Note )
(Note )
(Note )
1
1
1
1
(Note ) (Note )
(Note )
(Note )
1
1
1
1
68HC11
68HC912
Z80
(Note ) (Note )
(Note )
(Note )
1
1
1
E
DBE
AS
(Note )
(Note )
(Note )
1
1
1
RD
DS
DS
E
D3-D0
D7-D4
(Note ) (Note ) (Note )
1
1
1
1
Z8
AS
(Note ) (Note )
(Note )
(Note )
1
1
1
1
68330
AS
(Note ) (Note )
(Note )
(Note )
1
1
M37702M2
ALE
D3-D0
D7-D4
(Note ) (Note )
Note: 1. Unused CNTL2 pin can be configured as CPLD input. Other unused pins (PC7, PD0, PA3-0) can be configured for other I/O func-
tions.
2. ALE/AS input is optional for MCUs with a non-multiplexed bus
40/103
PSD81XFX, PSD83XF2, PSD85XF2
Figure 17. An Example of a Typical 8-bit Multiplexed Bus Interface
MCU
PSD
[
]
AD 7:0
[
]
A 7:0
PORT
A
(
(
)
)
OPTIONAL
ADIO
PORT
[
]
A 15:8
[
]
A 15:8
PORT
B
OPTIONAL
(
)
WR
RD
WR CNTRL0
(
)
RD CNTRL1
(
)
BHE
BHE CNTRL2
PORT
C
RST
ALE
(
)
ALE PD0
PORT D
RESET
AI02878C
41/103
PSD81XFX, PSD83XF2, PSD85XF2
PSD8XXFX Interface to a Non-Multiplexed 8-Bit
Bus. Figure 18 shows an example of a system us-
ing a MCU with an 8-bit non-multiplexed bus and
a PSD8XXFX. The address bus is connected to
the ADIO Port, and the data bus is connected to
Port A. Port A is in tri-state mode when the
PSD8XXFX is not accessed by the MCU. Should
the system address bus exceed sixteen bits, Ports
B, C, or D may be used for additional address in-
puts.
Data Byte Enable Reference. MCUs have differ-
ent data byte orientations. Table 16 shows how
the PSD8XXFX interprets byte/word operations in
different bus WRITE configurations. Even-byte re-
fers to locations with address A0 equal to 0 and
odd byte as locations with A0 equal to 1.
Table 16. Eight-Bit Data Bus
BHE
X
A0
0
D7-D0
Even Byte
Odd Byte
X
1
Figure 18. An Example of a Typical 8-bit Non-Multiplexed Bus Interface
PSD
MCU
[
]
D 7:0
[
]
D 7:0
PORT
A
ADIO
PORT
[
]
A 15:0
[
]
A 23:16
PORT
B
(OPTIONAL)
(
)
WR
RD
WR CNTRL0
(
)
RD CNTRL1
(
)
BHE
BHE CNTRL2
RST
PORT
C
ALE
(
)
ALE PD0
PORT D
RESET
AI02879C
42/103
PSD81XFX, PSD83XF2, PSD85XF2
MCU Bus Interface Examples
Figure 19 to Figure 22 show examples of the basic
connections between the PSD8XXFX and some
popular MCUs. The PSD8XXFX Control input pins
are labeled as to the MCU function for which they
are configured. The MCU bus interface is specified
using the PSDsoft Express Configuration.
with the data bus. The MCU control signals Pro-
gram Select Enable (PSEN, CNTL2), Read Strobe
(RD, CNTL1), and Write Strobe (WR, CNTL0) may
be used for accessing the internal memory and I/
O Ports blocks. Address Strobe (ALE/AS, PD0)
latches the address.
80C31. Figure 19 shows the bus interface for the
80C31, which has an 8-bit multiplexed address/
data bus. The lower address byte is multiplexed
80C251. The Intel 80C251 MCU features a user-
configurable bus interface with four possible bus
configurations, as shown in Table 17.
Figure 19. Interfacing the PSD8XXFX with an 80C31
AD7-AD0
[
]
AD 7:0
PSD
80C31
AD0
AD1
AD2
AD3
AD4
AD5
AD6
AD7
29
30
31
ADIO0
ADIO1
ADIO2
ADIO3
ADIO4
ADIO5
ADIO6
ADIO7
PA0
PA1
PA2
PA3
PA4
PA5
PA6
PA7
31
39
38
37
36
35
34
33
32
AD0
AD1
AD2
AD3
AD4
AD5
AD6
AD7
28
27
25
24
23
22
21
EA/VP
X1
P0.0
P0.1
P0.2
P0.3
P0.4
P0.5
P0.6
P0.7
32
33
34
35
36
37
19
18
9
X2
RESET
RESET
12
13
14
15
INT0
INT1
T0
21
22
23
24
25
26
27
28
A8
A9
39
40
41
42
43
44
45
46
7
6
5
4
3
2
52
51
P2.0
P2.1
P2.2
P2.3
P2.4
P2.5
P2.6
P2.7
ADIO8
ADIO9
PB0
PB1
PB2
PB3
PB4
PB5
PB6
PB7
A10
A11
A12
A13
A14
A15
ADIO10
ADIO11
ADIO12
ADIO13
ADIO14
ADIO15
T1
1
2
3
4
5
6
P1.0
P1.1
P1.2
P1.3
P1.4
P1.5
P1.6
P1.7
17
16
RD
RD
WR
20
19
18
17
14
13
12
11
WR
47
50
PC0
PC1
PC2
PC3
PC4
PC5
PC6
PC7
CNTL0(WR)
CNTL1(RD)
7
8
29
30
11
10
PSEN
ALE
PSEN
ALE/P
TXD
49
CNTL2(PSEN)
10
9
RXD
PD0-ALE
PD1
8
PD2
RESET
48
RESET
RESET
AI02880C
Table 17. 80C251 Configurations
80C251 READ/WRITE
Pins
Configuration
Connecting to PSD8XXFX Pins
Page Mode
WR
RD
PSEN
CNTL0
CNTL1
CNTL2
Non-Page Mode, 80C31
compatible A7-A0 multiplex with
D7-D0
1
WR
PSEN only
CNTL0
CNTL1
Non-Page Mode
A7-A0 multiplex with D7-D0
2
3
WR
PSEN only
CNTL0
CNTL1
Page Mode
A15-A8 multiplex with D7-D0
WR
RD
PSEN
CNTL0
CNTL1
CNTL2
Page Mode
A15-A8 multiplex with D7-D0
4
43/103
PSD81XFX, PSD83XF2, PSD85XF2
The first configuration is 80C31-compatible, and
the bus interface to the PSD8XXFX is identical to
that shown in Figure 19. The second and third con-
figurations have the same bus connection as
shown in Figure 18. There is only one Read Strobe
(PSEN) connected to CNTL1 on the PSD8XXFX.
The A16 connection to PA0 allows for a larger ad-
dress input to the PSD8XXFX. The fourth configu-
ration is shown in Figure 20. Read Strobe (RD) is
connected to CNTL1 and Program Select Enable
(PSEN) is connected to CNTL2.
mode, the data is multiplexed with the lower ad-
dress byte, and Address Strobe (ALE/AS, PD0) is
active in every bus cycle. In Page mode, data (D7-
D0) is multiplexed with address (A15-A8). In a bus
cycle where there is a Page hit, Address Strobe
(ALE/AS, PD0) is not active and only addresses
(A7-A0) are changing. The PSD8XXFX supports
both modes. In Page Mode, the PSD bus timing is
identical to Non-Page Mode except the address
hold time and setup time with respect to Address
Strobe (ALE/AS, PD0) is not required. The PSD
access time is measured from address (A7-A0)
valid to data in valid.
The 80C251 has two major operating modes:
Page mode and Non-page mode. In Non-page
Table 18. Interfacing the PSD8XXFX with the 80C251, with One READ Input
PSD
80C251SB
43
42
41
40
39
38
37
36
A0
A1
A2
A3
A4
A5
A6
A7
30
31
32
33
34
35
36
37
A0
A1
A2
A3
A4
A5
A6
A7
2
P0.0
P0.1
P0.2
P0.3
P0.4
P0.5
P0.6
P0.7
ADIO0
ADIO1
ADIO2
ADIO3
ADIO4
ADIO5
ADIO6
ADIO7
1
P1.0
P1.1
P1.2
P1.3
P1.4
P1.5
P1.6
P1.7
A16
29
28
27
25
24
23
22
21
3
4
5
6
7
8
9
PA0
PA1
PA2
PA3
PA4
PA5
1
A17
PA6
PA7
24
25
26
AD8
AD9
AD10
21
20
P2.0
P2.1
P2.2
P2.3
P2.4
P2.5
P2.6
X1
X2
AD8
39
40
41
42
43
44
45
46
ADIO8
ADIO9
ADIO10
ADIO11
ADIO12
ADIO13
ADIO14
ADIO15
7
6
5
4
3
2
52
51
AD9
PB0
PB1
PB2
PB3
PB4
PB5
PB6
PB7
27
28
AD11
AD12
AD10
AD11
AD12
AD13
AD14
AD15
11
13
14
15
16
17
P3.0/RXD
P3.1/TXD
P3.2/INT0
P3.3/INT1
P3.4/T0
29
30
AD13
AD14
AD15
31
P2.7
ALE
RD
47
50
33
32
P3.5/T1
(
)
CNTL0 WR
ALE
10
RST
RESET
(
)
CNTL1 RD
PSEN
20
19
18
17
14
13
12
11
18
19
WR
A16
PC0
PC1
PC2
PC3
PC4
PC5
PC6
PC7
WR
RD/A16
35
49
CNTL2(PSEN)
EA
10
9
8
PD0-ALE
PD1
PD2
48
RESET
RESET
RESET
AI02881C
Note: 1. The A16 and A17 connections are optional.
2. In non-Page-Mode, AD7-AD0 connects to ADIO7-ADIO0.
44/103
PSD81XFX, PSD83XF2, PSD85XF2
Figure 20. Interfacing the PSD8XXFX with the 80C251, with RD and PSEN Inputs
80C251SB
PSD
43
42
41
40
39
38
37
36
A0
A1
A2
A3
A4
A5
A6
A7
30
31
32
33
34
35
36
37
A0
A1
A2
A3
A4
A5
A6
A7
2
P0.0
P0.1
P0.2
P0.3
P0.4
P0.5
P0.6
P0.7
ADIO0
ADIO1
ADIO2
ADIO3
ADIO4
ADIO5
ADIO6
ADIO7
P1.0
P1.1
P1.2
P1.3
P1.4
P1.5
P1.6
P1.7
29
28
27
25
24
23
22
21
3
4
5
6
7
8
9
PA0
PA1
PA2
PA3
PA4
PA5
PA6
PA7
24
25
26
AD8
AD9
AD10
21
20
P2.0
P2.1
P2.2
P2.3
P2.4
P2.5
P2.6
X1
X2
AD8
39
40
41
42
43
44
45
46
ADIO8
ADIO9
ADIO10
ADIO11
ADIO12
ADIO13
ADIO14
ADIO15
7
6
5
4
3
2
52
51
AD9
PB0
PB1
PB2
PB3
PB4
PB5
PB6
PB7
27
28
AD11
AD12
AD10
AD11
AD12
AD13
AD14
AD15
11
13
14
15
16
17
P3.0/RXD
P3.1/TXD
P3.2/INT0
P3.3/INT1
P3.4/T0
29
30
AD13
AD14
AD15
31
P2.7
P3.5/T1
33
32
ALE
RD
47
50
(
)
CNTL0 WR
ALE
10
RST
EA
RESET
(
)
CNTL1 RD
PSEN
20
19
18
17
14
13
12
11
18
19
WR
PC0
PC1
PC2
PC3
PC4
PC5
PC6
PC7
WR
RD/A16
PSEN
35
49
CNTL2(PSEN)
10
9
8
PD0-ALE
PD1
PD2
48
RESET
RESET
RESET
AI02882C
45/103
PSD81XFX, PSD83XF2, PSD85XF2
80C51XA. The Philips 80C51XA MCU family sup-
ports an 8- or 16-bit multiplexed bus that can have
burst cycles. Address bits (A3-A0) are not multi-
plexed, while (A19-A4) are multiplexed with data
bits (D15-D0) in 16-bit mode. In 8-bit mode, (A11-
A4) are multiplexed with data bits (D7-D0).
The 80C51XA can be configured to operate in
eight-bit data mode (as shown in Figure 21).
The 80C51XA improves bus throughput and per-
formance by executing burst cycles for code fetch-
es. In Burst Mode, address A19-A4 are latched
internally by the PSD8XXFX, while the 80C51XA
changes the A3-A0 signals to fetch up to 16 bytes
of code. The PSD access time is then measured
from address A3-A0 valid to data in valid. The PSD
bus timing requirement in Burst Mode is identical
to the normal bus cycle, except the address setup
and hold time with respect to Address Strobe
(ALE/AS, PD0) does not apply.
Figure 21. Interfacing the PSD8XXFX with the 80C51X, 8-bit Data Bus
80C51XA
PSD
21
20
30
31
32
33
34
35
36
37
A4D0
A5D1
A6D2
A7D3
A8D4
A9D5
A10D6
A11D7
2
3
4
5
43
42
41
40
39
A0
A1
A2
A3
A4D0
A5D1
A6D2
A7D3
A8D4
A9D5
A10D6
A11D7
A12
A13
A14
A15
A16
A17
A18
A19
XTAL1
XTAL2
ADIO0
A0/WRH
A1
29 A0
ADIO1
ADIO2
ADIO3
AD104
AD105
ADIO6
ADIO7
PA0
PA1
28 A1
27 A2
25 A3
24
23
22
A2
A3
A4D0
A5D1
A6D2
A7D3
A8D4
A9D5
A10D6
A11D7
A12D8
A13D9
A14D10
A15D11
A16D12
A17D13
A18D14
A19D15
PA2
PA3
PA4
PA5
PA6
11
13
6
RXD0
TXD0
RXD1
TXD1
7
21
PA7
38
37
A12
A13
A14
A15
A16
A17
A18
A19
39
40
41
42
43
44
45
46
ADIO8
ADIO9
9
8
16
7
36
24
25
26
27
28
29
30
31
T2EX
T2
T0
PB0
PB1
PB2
PB3
PB4
PB5
PB6
PB7
6
5
4
3
2
52
51
ADIO10
ADIO11
AD1012
AD1013
ADIO14
ADIO15
10
RST
INT0
INT1
RESET
14
15
47
50
(
)
CNTL0 WR
20
19
18
17
14
13
12
11
PC0
PC1
PC2
PC3
PC4
PC5
PC6
PC7
(
)
CNTL1 RD
PSEN
32
49
35
17
PSEN
RD
CNTL2(PSEN)
EA/WAIT
BUSW
19
18
33
RD
WR
10
8
9
PD0-ALE
PD1
WRL
ALE
ALE
PD2
48
RESET
RESET
AI02883C
46/103
PSD81XFX, PSD83XF2, PSD85XF2
68HC11. Figure 22 shows a bus interface to a
68HC11 where the PSD8XXFX is configured in 8-
bit multiplexed mode with E and R/W settings. The
DPLD can be used to generate the READ and WR
signals for external devices.
Figure 22. Interfacing the PSD8XXFX with a 68HC11
AD7-AD0
AD7-AD0
PSD
30
31
32
33
34
35
36
37
AD0
AD1
29
28
27
25
24
23
22
21
ADIO0
ADIO1
ADIO2
ADIO3
AD104
AD105
ADIO6
ADIO7
PA0
PA1
PA2
PA3
PA4
PA5
PA6
PA7
68HC11
AD2
AD3
AD4
AD5
AD6
AD7
31
PA3
PA4
PA5
PA6
PA7
8
7
30
29
28
27
XT
EX
17
19
18
RESET
RESET
IRQ
XIRQ
39
40
41
42
43
44
45
46
7
6
5
4
3
2
52
51
42
41
40
39
38
37
36
35
A8
A9
A10
A11
A12
A13
A14
A15
ADIO8
ADIO9
PB0
PB1
PB2
PB3
PB4
PB5
PB6
PB7
PB0
PB1
PB2
PB3
PB4
PB5
PB6
PB7
2
MODB
ADIO10
ADIO11
AD1012
AD1013
ADIO14
ADIO15
34
33
32
PA0
PA1
PA2
9
AD0
AD1
AD2
AD3
AD4
AD5
AD6
AD7
PC0
PC1
PC2
PC3
PC4
PC5
PC6
PC7
43
44
45
46
47
48
49
50
20
19
18
17
14
13
12
11
10
11
12
13
14
15
16
PE0
PE1
PE2
PE3
PE4
PE5
PE6
PE7
PC0
PC1
PC2
PC3
PC4
47
50
_
CNTL0(R W)
CNTL1(E)
49
CNTL2
PC5
PC6
PC7
10
9
8
PD0 AS
–
PD1
PD2
20
21
22
23
24
25
52
51
PD0
PD1
PD2
PD3
PD4
PD5
VRH
VRL
48
RESET
3
MODA
5
4
6
E
E
AS
R/W
AS
R/W
RESET
AI02884C
47/103
PSD81XFX, PSD83XF2, PSD85XF2
I/O PORTS
There are four programmable I/O ports: Ports A, B,
C, and D. Each of the ports is eight bits except Port
D, which is 3 bits. Each port pin is individually user
configurable, thus allowing multiple functions per
port. The ports are configured using PSDsoft Ex-
press Configuration or by the MCU writing to on-
chip registers in the CSIOP space.
that pin is no longer available for other purposes.
Exceptions are noted.
As shown in Figure 23, the ports contain an output
multiplexer whose select signals are driven by the
configuration bits in the Control Registers (Ports A
and B only) and PSDsoft Express Configuration.
Inputs to the multiplexer include the following:
The topics discussed in this section are:
■ General Port architecture
■ Port operating modes
■ Output data from the Data Out register
■ Latched address outputs
■ CPLD macrocell output
■ Port Configuration Registers (PCR)
■ Port Data Registers
■ External Chip Select (ECS0-ECS2) from the
CPLD.
■ Individual Port functionality.
General Port Architecture
The general architecture of the I/O Port block is
shown in Figure 23. Individual Port architectures
are shown in Figure 25 to Figure 28. In general,
once the purpose for a port pin has been defined,
The Port Data Buffer (PDB) is a tri-state buffer that
allows only one source at a time to be read. The
Port Data Buffer (PDB) is connected to the Internal
Data Bus for feedback and can be read by the
MCU. The Data Out and macrocell outputs, Direc-
tion and Control Registers, and port pin input are
all connected to the Port Data Buffer (PDB).
Figure 23. General I/O Port Architecture
DATA OUT
REG.
DATA OUT
D
Q
WR
ADDRESS
ALE
ADDRESS
PORT PIN
D
G
Q
OUTPUT
MUX
MACROCELL OUTPUTS
EXT CS
READ MUX
P
D
B
OUTPUT
SELECT
DATA IN
CONTROL REG.
ENABLE OUT
D
Q
WR
WR
DIR REG.
D
Q
(
)
ENABLE PRODUCT TERM .OE
INPUT
MACROCELL
CPLD-INPUT
AI02885
48/103
PSD81XFX, PSD83XF2, PSD85XF2
The Port pin’s tri-state output driver enable is con-
trolled by a two input OR gate whose inputs come
from the CPLD AND Array enable product term
and the Direction Register. If the enable product
term of any of the Array outputs are not defined
and that port pin is not defined as a CPLD output
in the PSDabel file, then the Direction Register has
sole control of the buffer that drives the port pin.
The contents of these registers can be altered by
the MCU. The Port Data Buffer (PDB) feedback
path allows the MCU to check the contents of the
registers.
Ports A, B, and C have embedded Input Macro-
cells (IMC). The Input Macrocells (IMC) can be
configured as latches, registers, or direct inputs to
the PLDs. The latches and registers are clocked
by Address Strobe (ALE/AS, PD0) or a product
term from the PLD AND Array. The outputs from
the Input Macrocells (IMC) drive the PLD input bus
and can be read by the MCU. See the section en-
titled “Input Macrocell”, on page 38.
A port pin can be put into MCU I/O mode by writing
a 0 to the corresponding bit in the Control Regis-
ter. The MCU I/O direction may be changed by
writing to the corresponding bit in the Direction
Register, or by the output enable product term.
See the section entitled “Peripheral I/O Mode”, on
page 51. When the pin is configured as an output,
the content of the Data Out Register drives the pin.
When configured as an input, the MCU can read
the port input through the Data In buffer. See Fig-
ure 23.
Ports C and D do not have Control Registers, and
are in MCU I/O mode by default. They can be used
for PLD I/O if equations are written for them in PS-
Dabel.
PLD I/O Mode
The PLD I/O Mode uses a port as an input to the
CPLD’s Input Macrocells (IMC), and/or as an out-
put from the CPLD’s Output Macrocells (OMC).
The output can be tri-stated with a control signal.
This output enable control signal can be defined
by a product term from the PLD, or by resetting the
corresponding bit in the Direction Register to 0.
The corresponding bit in the Direction Register
must not be set to 1 if the pin is defined for a PLD
input signal in PSDabel. The PLD I/O mode is
specified in PSDabel by declaring the port pins,
and then writing an equation assigning the PLD I/
O to a port.
Port Operating Modes
The I/O Ports have several modes of operation.
Some modes can be defined using PSDabel,
some by the MCU writing to the Control Registers
in CSIOP space, and some by both. The modes
that can only be defined using PSDsoft Express
must be programmed into the device and cannot
be changed unless the device is reprogrammed.
The modes that can be changed by the MCU can
be done so dynamically at run-time. The PLD I/O,
Data Port, Address Input, and Peripheral I/O
modes are the only modes that must be defined
before programming the device. All other modes
can be changed by the MCU at run-time. See Ap-
plication Note AN1171 for more detail.
Address Out Mode
For MCUs with a multiplexed address/data bus,
Address Out Mode can be used to drive latched
addresses on to the port pins. These port pins can,
in turn, drive external devices. Either the output
enable or the corresponding bits of both the Direc-
tion Register and Control Register must be set to
a 1 for pins to use Address Out Mode. This must
be done by the MCU at run-time. See Table 21 for
the address output pin assignments on Ports A
and B for various MCUs.
For non-multiplexed 8-bit bus mode, address sig-
nals (A7-A0) are available to Port B in Address Out
Mode.
Note: Do not drive address signals with Address
Out Mode to an external memory device if it is in-
tended for the MCU to Boot from the external de-
vice. The MCU must first Boot from PSD8XXFX
memory so the Direction and Control register bits
can be set.
Table 19 summarizes which modes are available
on each port. Table 22 shows how and where the
different modes are configured. Each of the port
operating modes are described in the following
sections.
MCU I/O Mode
In the MCU I/O mode, the MCU uses the I/O Ports
block to expand its own I/O ports. By setting up the
CSIOP space, the ports on the PSD8XXFX are
mapped into the MCU address space. The ad-
dresses of the ports are listed in Table 7.
49/103
PSD81XFX, PSD83XF2, PSD85XF2
Table 19. Port Operating Modes
Port Mode
MCU I/O
Port A
Port B
Port C
Port D
Yes
Yes
Yes
Yes
PLD I/O
McellAB Outputs
McellBC Outputs
Additional Ext. CS Outputs No
Yes
No
Yes
Yes
No
No
Yes
No
Yes
No
No
Yes
Yes
PLD Inputs
Yes
Yes
Yes (A7 – 0)
or (A15 – 8)
Address Out
Yes (A7 – 0)
No
No
Address In
Data Port
Yes
Yes
No
No
No
Yes
No
No
Yes
No
No
No
Yes (D7 – 0)
Peripheral I/O
JTAG ISP
Yes
No
1
Yes
Note: 1. Can be multiplexed with other I/O functions.
Table 20. Port Operating Mode Settings
Defined in
PSD8XXFX
Configuration
Control
Register
Setting
Direction
Register
Setting
VM
Defined in
PSDabel
Mode
Register JTAG Enable
Setting
1 = output,
0 = input
1
MCU I/O
Declare pins only
0
N/A
N/A
N/A
2
(Note )
2
PLD I/O
Logic equations
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
(Note )
Data Port (Port A)
Specify bus type
N/A
Address Out
(Port A,B)
2
Declare pins only
N/A
N/A
N/A
1
N/A
N/A
N/A
N/A
1 (Note )
Address In
(Port A,B,C,D)
Logic for equation
Input Macrocells
N/A
N/A
N/A
N/A
N/A
N/A
Peripheral I/O
(Port A)
Logic equations
(PSEL0 & 1)
PIO bit = 1 N/A
N/A JTAG_Enable
JTAG
Configuration
3
JTAGSEL
JTAG ISP (Note )
Note: 1. N/A = Not Applicable
2. The direction of the Port A,B,C, and D pins are controlled by the Direction Register ORed with the individual output enable product
term (.oe) from the CPLD AND Array.
3. Any of these three methods enables the JTAG pins on Port C.
50/103
PSD81XFX, PSD83XF2, PSD85XF2
Table 21. I/O Port Latched Address Output Assignments
MCU
Port A (PA3-PA0)
Port A (PA7-PA4)
Port B (PB3-PB0)
Port B (PB7-PB4)
N/A
1
8051XA (8-Bit)
Address a7-a4
Address a11-a8
N/A
80C251
(Page Mode)
N/A
N/A
Address a11-a8
Address a3-a0
Address a3-a0
Address a15-a12
Address a7-a4
Address a7-a4
All Other
8-Bit Multiplexed
Address a3-a0
N/A
Address a7-a4
N/A
8-Bit
Non-Multiplexed Bus
Note: 1. N/A = Not Applicable.
Address In Mode
For MCUs that have more than 16 address sig-
nals, the higher addresses can be connected to
Port A, B, C, and D. The address input can be
latched in the Input Macrocell (IMC) by Address
Strobe (ALE/AS, PD0). Any input that is included
in the DPLD equations for the SRAM, or primary or
secondary Flash memory is considered to be an
address input.
serves as a tri-state, bi-directional data buffer for
the MCU. Peripheral I/O Mode is enabled by set-
ting Bit 7 of the VM Register to a 1. Figure 24
shows how Port A acts as a bi-directional buffer for
the MCU data bus if Peripheral I/O Mode is en-
abled. An equation for PSEL0 and/or PSEL1 must
be written in PSDabel. The buffer is tri-stated
when PSEL0 or PSEL1 is not active.
Data Port Mode
JTAG In-System Programming (ISP)
Port A can be used as a data bus port for a MCU
with a non-multiplexed address/data bus. The
Data Port is connected to the data bus of the MCU.
The general I/O functions are disabled in Port A if
the port is configured as a Data Port.
Peripheral I/O Mode
Peripheral I/O mode can be used to interface with
external peripherals. In this mode, all of Port A
Port C is JTAG compliant, and can be used for In-
System Programming (ISP). You can multiplex
JTAG operations with other functions on Port C
because In-System Programming (ISP) is not per-
formed in normal Operating mode. For more infor-
mation on the JTAG Port, see the section entitled
“PROGRAMMING IN-CIRCUIT USING THE
JTAG SERIAL INTERFACE”, on page 65.
Figure 24. Peripheral I/O Mode
RD
PSEL0
PSEL
PSEL1
D0-D7
VM REGISTER BIT 7
PA0-PA7
DATA BUS
WR
AI02886
51/103
PSD81XFX, PSD83XF2, PSD85XF2
Port Configuration Registers (PCR)
Each Port has a set of Port Configuration Regis-
ters (PCR) used for configuration. The contents of
the registers can be accessed by the MCU through
normal READ/WRITE bus cycles at the addresses
given in Table 7. The addresses in Table 7 are the
offsets in hexadecimal from the base of the CSIOP
register.
The pins of a port are individually configurable and
each bit in the register controls its respective pin.
For example, Bit 0 in a register refers to Bit 0 of its
port. The three Port Configuration Registers
(PCR), shown in Table 22, are used for setting the
Port configurations. The default Power-up state for
each register in Table 22 is 00h.
Note that the slew rate is a measurement of the
rise and fall times of an output. A higher slew rate
means a faster output response and may create
more electrical noise. A pin operates in a high slew
rate when the corresponding bit in the Drive Reg-
ister is set to 1. The default rate is slow slew.
Table 26 shows the Drive Register for Ports A, B,
C, and D. It summarizes which pins can be config-
ured as Open Drain outputs and which pins the
slew rate can be set for.
Table 22. Port Configuration Registers (PCR)
Register Name
Control
Port
MCU Access
WRITE/READ
WRITE/READ
WRITE/READ
Control Register. Any bit reset to 0 in the Control
Register sets the corresponding port pin to MCU I/
O Mode, and a 1 sets it to Address Out Mode. The
default mode is MCU I/O. Only Ports A and B have
an associated Control Register.
A,B
Direction
A,B,C,D
A,B,C,D
1
Drive Select
Note: 1. See Table 26 for Drive Register bit definition.
Direction Register. The Direction Register, in
conjunction with the output enable (except for Port
D), controls the direction of data flow in the I/O
Ports. Any bit set to 1 in the Direction Register
causes the corresponding pin to be an output, and
any bit set to 0 causes it to be an input. The default
mode for all port pins is input.
Figure 25, page 54 and Figure 26, page 55 show
the Port Architecture diagrams for Ports A/B and
C, respectively. The direction of data flow for Ports
A, B, and C are controlled not only by the direction
register, but also by the output enable product
term from the PLD AND Array. If the output enable
product term is not active, the Direction Register
has sole control of a given pin’s direction.
Table 23. Port Pin Direction Control, Output
Enable P.T. Not Defined
Direction Register Bit
Port Pin Mode
0
1
Input
Output
Table 24. Port Pin Direction Control, Output
Enable P.T. Defined
Direction
Register Bit
Output Enable
P.T.
Port Pin Mode
0
0
1
1
0
Input
An example of a configuration for a Port with the
three least significant bits set to output and the re-
mainder set to input is shown in Table 25. Since
Port D only contains three pins (shown in Figure
28), the Direction Register for Port D has only the
three least significant bits active.
1
0
1
Output
Output
Output
Drive Select Register. The Drive Select Register
configures the pin driver as Open Drain or CMOS
for some port pins, and controls the slew rate for
the other port pins. An external pull-up resistor
should be used for pins configured as Open Drain.
Table 25. Port Direction Assignment Example
Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0
0
0
0
0
0
1
1
1
A pin can be configured as Open Drain if its corre-
sponding bit in the Drive Select Register is set to a
1. The default pin drive is CMOS.
52/103
PSD81XFX, PSD83XF2, PSD85XF2
Table 26. Drive Register Pin Assignment
Drive
Bit 7
Bit 6
Bit 5
Bit 4
Open
Bit 3
Slew
Bit 2
Slew
Bit 1
Slew
Bit 0
Slew
Register
Open
Drain
Open
Drain
Open
Drain
Port A
Drain
Rate
Rate
Rate
Rate
Open
Drain
Open
Drain
Open
Drain
Open
Drain
Slew
Rate
Slew
Rate
Slew
Rate
Slew
Rate
Port B
Port C
Port D
Open
Drain
Open
Drain
Open
Drain
Open
Drain
Open
Drain
Open
Drain
Open
Drain
Open
Drain
Slew
Rate
Slew
Rate
Slew
Rate
1
1
1
1
1
NA
NA
NA
NA
NA
Note: 1. NA = Not Applicable.
Port Data Registers
The Port Data Registers, shown in Table 27, are
used by the MCU to write data to or read data from
the ports. Table 27 shows the register name, the
ports having each register type, and MCU access
for each register type. The registers are described
below.
Data In. Port pins are connected directly to the
Data In buffer. In MCU I/O input mode, the pin in-
put is read through the Data In buffer.
Data Out Register. Stores output data written by
the MCU in the MCU I/O output mode. The con-
tents of the Register are driven out to the pins if the
Direction Register or the output enable product
term is set to 1. The contents of the register can
also be read back by the MCU.
Output Macrocells (OMC). The CPLD Output
Macrocells (OMC) occupy a location in the MCU’s
address space. The MCU can read the output of
the Output Macrocells (OMC). If the OMC Mask
Register bits are not set, writing to the macrocell
loads data to the macrocell flip-flops. See the sec-
tion entitled “PLDS”, on page 30.
OMC Mask Register. Each OMC Mask Register
bit corresponds to an Output Macrocell (OMC) flip-
flop. When the OMC Mask Register bit is set to a
1, loading data into the Output Macrocell (OMC)
flip-flop is blocked. The default value is 0 or un-
blocked.
Input Macrocells (IMC). The Input Macrocells
(IMC) can be used to latch or store external inputs.
The outputs of the Input Macrocells (IMC) are rout-
ed to the PLD input bus, and can be read by the
MCU. See the section entitled “PLDS”, on page
30.
Enable Out. The Enable Out register can be read
by the MCU. It contains the output enable values
for a given port. A 1 indicates the driver is in output
mode. A 0 indicates the driver is in tri-state and the
pin is in input mode.
Table 27. Port Data Registers
Register Name
Port
A,B,C,D
MCU Access
Data In
READ – input on pin
Data Out
A,B,C,D
A,B,C
WRITE/READ
READ – outputs of macrocells
WRITE – loading macrocells flip-flop
Output Macrocell
Mask Macrocell
WRITE/READ – prevents loading into a given
macrocell
A,B,C
Input Macrocell
Enable Out
A,B,C
A,B,C
READ – outputs of the Input Macrocells
READ – the output enable control of the port driver
53/103
PSD81XFX, PSD83XF2, PSD85XF2
Ports A and B – Functionality and Structure
Ports A and B have similar functionality and struc-
ture, as shown in Figure 25. The two ports can be
configured to perform one or more of the following
functions:
■ Address In – Additional high address inputs
using the Input Macrocells (IMC).
■ Open Drain/Slew Rate – pins PA3-PA0 and
PB3-PB0 can be configured to fast slew rate,
pins PA7-PA4 and PB7-PB4 can be configured
to Open Drain Mode.
■ MCU I/O Mode
■ CPLD Output – Macrocells McellAB7-McellAB0
can be connected to Port A or Port B. McellBC7-
McellBC0 can be connected to Port B or Port C.
■ Data Port – Port A to D7-D0 for 8 bit non-
multiplexed bus
■ CPLD Input – Via the Input Macrocells (IMC).
■ Multiplexed Address/Data port for certain types
of MCU bus interfaces.
■ Latched Address output – Provide latched
address output as per Table 21.
■ Peripheral Mode – Port A only
Figure 25. Port A and Port B Structure
DATA OUT
REG.
DATA OUT
D
Q
WR
PORT
A OR B PIN
ADDRESS
ALE
ADDRESS
D
G
Q
[
]
[
]
A 7:0 OR A 15:8
OUTPUT
MUX
MACROCELL OUTPUTS
READ MUX
P
D
B
OUTPUT
SELECT
DATA IN
CONTROL REG.
ENABLE OUT
D
Q
WR
WR
DIR REG.
D
Q
(
)
ENABLE PRODUCT TERM .OE
CPLD-INPUT
INPUT
MACROCELL
AI02887
54/103
PSD81XFX, PSD83XF2, PSD85XF2
Port C – Functionality and Structure
Port C can be configured to perform one or more
of the following functions (see Figure 26):
■ Open Drain – Port C pins can be configured in
Open Drain Mode
■ MCU I/O Mode
■ Battery Backup features – PC2 can be
configured for a battery input supply, Voltage
■ CPLD Output – McellBC7-McellBC0 outputs
Stand-by (V
).
STBY
can be connected to Port B or Port C.
PC4 can be configured as a Battery-on Indicator
(VBATON), indicating when V is less than
■ CPLD Input – via the Input Macrocells (IMC)
CC
■ Address In – Additional high address inputs
V
.
BAT
using the Input Macrocells (IMC).
Port C does not support Address Out mode, and
therefore no Control Register is required.
Pin PC7 may be configured as the DBE input in
certain MCU bus interfaces.
■ In-System Programming (ISP) – JTAG port can
be enabled for programming/erase of the
PSD8XXFX device. (See the section entitled
“PROGRAMMING IN-CIRCUIT USING THE
JTAG SERIAL INTERFACE”, on page 65, for
more information on JTAG programming.)
Figure 26. Port C Structure
DATA OUT
REG.
DATA OUT
D
Q
WR
PORT C PIN
1
SPECIAL FUNCTION
OUTPUT
MUX
[
]
MCELLBC 7:0
READ MUX
P
D
B
OUTPUT
SELECT
DATA IN
ENABLE OUT
DIR REG.
D
Q
WR
(
)
ENABLE PRODUCT TERM .OE
INPUT
MACROCELL
1
SPECIAL FUNCTION
CPLD-INPUT
CONFIGURATION
BIT
AI02888B
55/103
PSD81XFX, PSD83XF2, PSD85XF2
Port D – Functionality and Structure
Port D has three I/O pins. See Figure 27 and Fig-
ure 28. This port does not support Address Out
mode, and therefore no Control Register is re-
quired. Port D can be configured to perform one or
more of the following functions:
■ Slew rate – pins can be set up for fast slew rate
Port D pins can be configured in PSDsoft Express
as input pins for other dedicated functions:
■ Address Strobe (ALE/AS, PD0)
■ CLKIN (PD1) as input to the macrocells flip-
■ MCU I/O Mode
flops and APD counter
■ CPLD Output – External Chip Select (ECS0-
■ PSD Chip Select Input (CSI, PD2). Driving this
signal High disables the Flash memory, SRAM
and CSIOP.
ECS2)
■ CPLD Input – direct input to the CPLD, no Input
Macrocells (IMC)
Figure 27. Port D Structure
DATA OUT
REG.
DATA OUT
D
Q
WR
PORT D PIN
OUTPUT
MUX
[
]
ECS 2:0
READ MUX
OUTPUT
SELECT
P
D
B
DATA IN
ENABLE PRODUCT
TERM (.OE)
DIR REG.
D
Q
WR
CPLD-INPUT
AI02889
56/103
PSD81XFX, PSD83XF2, PSD85XF2
External Chip Select
The CPLD also provides three External Chip Se-
lect (ECS0-ECS2) outputs on Port D pins that can
be used to select external devices. Each External
Chip Select (ECS0-ECS2) consists of one product
term that can be configured active High or Low.
The output enable of the pin is controlled by either
the output enable product term or the Direction
Register. (See Figure 28.)
Figure 28. Port D External Chip Select Signals
ENABLE (.OE)
DIRECTION
REGISTER
PD0 PIN
ECS0
PT0
PT1
PT2
POLARITY
BIT
ENABLE (.OE)
DIRECTION
REGISTER
PD1 PIN
ECS1
POLARITY
BIT
ENABLE (.OE)
DIRECTION
REGISTER
PD2 PIN
ECS2
POLARITY
BIT
AI02890
57/103
PSD81XFX, PSD83XF2, PSD85XF2
POWER MANAGEMENT
All PSD8XXFX devices offer configurable power
saving options. These options may be used indi-
vidually or in combinations, as follows:
and PLDs to remain in standby mode even if the
address/data signals are changing state
externally (noise, other devices on the MCU
bus, etc.). Keep in mind that any unblocked PLD
input signals that are changing states keeps the
PLD out of Stand-by mode, but not the
memories.
■ All memory blocks in a PSD8XXFX (primary and
secondary Flash memory, and SRAM) are built
with power management technology. In addition
to using special silicon design methodology,
power management technology puts the
memories into standby mode when address/
data inputs are not changing (zero DC current).
As soon as a transition occurs on an input, the
affected memory “wakes up”, changes and
latches its outputs, then goes back to standby.
The designer does not have to do anything
special to achieve memory standby mode when
no inputs are changing—it happens
■ PSD Chip Select Input (CSI, PD2) can be used
to disable the internal memories, placing them
in standby mode even if inputs are changing.
This feature does not block any internal signals
or disable the PLDs. This is a good alternative
to using the APD Unit. There is a slight penalty
in memory access time when PSD Chip Select
Input (CSI, PD2) makes its initial transition from
deselected to selected.
automatically.
■ The PMMRs can be written by the MCU at run-
time to manage power. All PSD8XXFX supports
“blocking bits” in these registers that are set to
block designated signals from reaching both
PLDs. Current consumption of the PLDs is
directly related to the composite frequency of
the changes on their inputs (see Figure 32 and
Figure 33). Significant power savings can be
achieved by blocking signals that are not used
in DPLD or CPLD logic equations.
The PLD sections can also achieve Stand-by
mode when its inputs are not changing, as
described in the sections on the Power
Management Mode Registers (PMMR).
■ As with the Power Management mode, the
Automatic Power Down (APD) block allows the
PSD8XXFX to reduce to stand-by current
automatically. The APD Unit can also block
MCU address/data signals from reaching the
memories and PLDs. This feature is available
on all the devices of the PSD8XXFX family. The
APD Unit is described in more detail in the
sections entitled “Automatic Power-down (APD)
Unit and Power-down Mode”, on page 59.
PSD8XXFX devices have a Turbo bit in
PMMR0. This bit can be set to turn the Turbo
mode off (the default is with Turbo mode turned
on). While Turbo mode is off, the PLDs can
achieve standby current when no PLD inputs
are changing (zero DC current). Even when
inputs do change, significant power can be
saved at lower frequencies (AC current),
compared to when Turbo mode is on. When the
Turbo mode is on, there is a significant DC
current component and the AC component is
higher.
Built in logic monitors the Address Strobe of the
MCU for activity. If there is no activity for a
certain time period (MCU is asleep), the APD
Unit initiates Power-down mode (if enabled).
Once in Power-down mode, all address/data
signals are blocked from reaching PSD8XXFX
memory and PLDs, and the memories are
deselected internally. This allows the memory
58/103
PSD81XFX, PSD83XF2, PSD85XF2
Automatic Power-down (APD) Unit and Power-
down Mode. The APD Unit, shown in Figure 29,
puts the PSD8XXFX into Power-down mode by
monitoring the activity of Address Strobe (ALE/AS,
PD0). If the APD Unit is enabled, as soon as activ-
ity on Address Strobe (ALE/AS, PD0) stops, a four
bit counter starts counting. If Address Strobe
(ALE/AS, PD0) remains inactive for fifteen clock
periods of CLKIN (PD1), Power-down (PDN) goes
High, and the PSD8XXFX enters Power-down
mode, as discussed next.
Power-down Mode. By default, if you enable the
APD Unit, Power-down mode is automatically en-
abled. The device enters Power-down mode if Ad-
dress Strobe (ALE/AS, PD0) remains inactive for
fifteen periods of CLKIN (PD1).
the appropriate bits in the PMMR registers. The
blocked signals include MCU control signals
and the common CLKIN (PD1). Note that
blocking CLKIN (PD1) from the PLDs does not
block CLKIN (PD1) from the APD Unit.
■ All PSD8XXFX memories enter Standby mode
and are drawing standby current. However, the
PLD and I/O ports blocks do not go into Standby
Mode because you don’t want to have to wait for
the logic and I/O to “wake-up” before their
outputs can change. See Table 28 for Power-
down mode effects on PSD8XXFX ports.
■ Typical standby current is of the order of
microamperes. These standby current values
assume that there are no transitions on any PLD
input.
The following should be kept in mind when the
PSD8XXFX is in Power-down mode:
Table 28. Power-down Mode’s Effect on Ports
■ If Address Strobe (ALE/AS, PD0) starts pulsing
again, the PSD8XXFX returns to normal
Operating mode. The PSD8XXFX also returns
to normal Operating mode if either PSD Chip
Select Input (CSI, PD2) is Low or the Reset
(RESET) input is High.
Port Function
MCU I/O
Pin Level
No Change
PLD Out
No Change
Undefined
Tri-State
Address Out
Data Port
■ The MCU address/data bus is blocked from all
memory and PLDs.
■ Various signals can be blocked (prior to Power-
Peripheral I/O
Tri-State
down mode) from entering the PLDs by setting
Figure 29. APD Unit
APD EN
PMMR0 BIT 1=1
TRANSITION
DETECTION
DISABLE BUS
INTERFACE
ALE
PD
CLR
APD
EEPROM SELECT
FLASH SELECT
COUNTER
RESET
EDGE
DETECT
PD
CSI
PLD
SRAM SELECT
POWER DOWN
CLKIN
(
)
PDN SELECT
DISABLE
FLASH/EEPROM/SRAM
AI02891
Table 29. PSD8XXFX Timing and Stand-by Current during Power-down Mode
Typical Stand-by Current
5V V 3V V
PLD Propagation
Delay
Memory
Access Time
Access Recovery Time
to Normal Access
Mode
CC
CC
1
2
2
t
Power-down
No Access
Normal t (Note )
LVDV
75 µA (Note ) 25 µA (Note )
PD
Note: 1. Power-down does not affect the operation of the PLD. The PLD operation in this mode is based only on the Turbo bit.
2. Typical current consumption assuming no PLD inputs are changing state and the PLD Turbo bit is 0.
59/103
PSD81XFX, PSD83XF2, PSD85XF2
For Users of the HC11 (or compatible). The
HC11 turns off its E clock when it sleeps. There-
fore, if you are using an HC11 (or compatible) in
your design, and you wish to use the Power-down
mode, you must not connect the E clock to CLKIN
(PD1). You should instead connect a crystal oscil-
lator to CLKIN (PD1). The crystal oscillator fre-
quency must be less than 15 times the frequency
of AS. The reason for this is that if the frequency is
greater than 15 times the frequency of AS, the
PSD8XXFX keeps going into Power-down mode.
Other Power Saving Options. The PSD8XXFX
offers other reduced power saving options that are
independent of the Power-down mode. Except for
the SRAM Stand-by and PSD Chip Select Input
(CSI, PD2) features, they are enabled by setting
bits in PMMR0 and PMMR2.
Figure 30. Enable Power-down Flow Chart
RESET
Enable APD
Set PMMR0 Bit 1 = 1
OPTIONAL
Disable desired inputs to PLD
by setting PMMR0 bits 4 and 5
and PMMR2 bits 2 through 6.
ALE/AS idle
for 15 CLKIN
clocks?
No
Yes
PSD in Power
Down Mode
AI02892
60/103
PSD81XFX, PSD83XF2, PSD85XF2
PLD Power Management
The power and speed of the PLDs are controlled
by the Turbo bit (bit 3) in PMMR0. By setting the
bit to 1, the Turbo mode is off and the PLDs con-
sume the specified stand-by current when the in-
puts are not switching for an extended time of
70ns. The propagation delay time is increased by
10ns after the Turbo bit is set to 1 (turned off) when
the inputs change at a composite frequency of less
than 15 MHz. When the Turbo bit is reset to 0
(turned on), the PLDs run at full power and speed.
The Turbo bit affects the PLD’s DC power, AC
power, and propagation delay.
Blocking MCU control signals with the bits of
PMMR2 can further reduce PLD AC power con-
sumption.
Table 30. Power Management Mode Registers PMMR0 (Note 1)
Bit 0
Bit 1
Bit 2
Bit 3
X
0
Not used, and should be set to zero.
0 = off Automatic Power-down (APD) is disabled.
1 = on Automatic Power-down (APD) is enabled.
APD Enable
X
0
Not used, and should be set to zero.
0 = on PLD Turbo mode is on
PLD Turbo
1 = off PLD Turbo mode is off, saving power.
CLKIN (PD1) input to the PLD AND Array is connected. Every change of CLKIN
(PD1) Powers-up the PLD when Turbo bit is 0.
0 = on
Bit 4
Bit 5
PLD Array clk
PLD MCell clk
1 = off CLKIN (PD1) input to PLD AND Array is disconnected, saving power.
0 = on CLKIN (PD1) input to the PLD macrocells is connected.
1 = off CLKIN (PD1) input to PLD macrocells is disconnected, saving power.
Bit 6
Bit 7
X
X
0
0
Not used, and should be set to zero.
Not used, and should be set to zero.
Note: 1. The bits of this register are cleared to zero following Power-up. Subsequent Reset (RESET) pulses do not clear the registers.
Table 31. Power Management Mode Registers PMMR2 (Note 1)
Bit 0
Bit 1
X
X
0
0
Not used, and should be set to zero.
Not used, and should be set to zero.
0 = on Cntl0 input to the PLD AND Array is connected.
PLD Array
CNTL0
Bit 2
Bit 3
Bit 4
Bit 5
1 = off Cntl0 input to PLD AND Array is disconnected, saving power.
0 = on Cntl1 input to the PLD AND Array is connected.
PLD Array
CNTL1
1 = off Cntl1 input to PLD AND Array is disconnected, saving power.
0 = on Cntl2 input to the PLD AND Array is connected.
PLD Array
CNTL2
1 = off Cntl2 input to PLD AND Array is disconnected, saving power.
0 = on ALE input to the PLD AND Array is connected.
PLD Array
ALE
1 = off ALE input to PLD AND Array is disconnected, saving power.
0 = on DBE input to the PLD AND Array is connected.
PLD Array
DBE
Bit 6
Bit 7
1 = off DBE input to PLD AND Array is disconnected, saving power.
X
0
Not used, and should be set to zero.
Note: 1. The bits of this register are cleared to zero following Power-up. Subsequent Reset (RESET) pulses do not clear the registers.
61/103
PSD81XFX, PSD83XF2, PSD85XF2
SRAM Standby Mode (Battery Backup). The
PSD8XXFX supports a battery backup mode in
which the contents of the SRAM are retained in the
event of a power loss. The SRAM has Voltage
There may be a timing penalty when using PSD
Chip Select Input (CSI, PD2) depending on the
speed grade of the PSD8XXFX that you are using.
See the timing parameter t
ble 61.
in Table 60 or Ta-
SLQV
Stand-by (V
, PC2) that can be connected to
STBY
an external battery. When V
becomes lower
CC
Input Clock
than V
then the PSD8XXFX automatically
STBY
The PSD8XXFX provides the option to turn off
CLKIN (PD1) to the PLD to save AC power con-
sumption. CLKIN (PD1) is an input to the PLD
AND Array and the Output Macrocells (OMC).
During Power-down mode, or, if CLKIN (PD1) is
not being used as part of the PLD logic equation,
the clock should be disabled to save AC power.
CLKIN (PD1) is disconnected from the PLD AND
Array or the Macrocells block by setting bits 4 or 5
to a 1 in PMMR0.
connects to Voltage Stand-by (V
, PC2) as a
STBY
power source to the SRAM. The SRAM Standby
Current (I ) is typically 0.5 µA. The SRAM data
STBY
retention voltage is 2 V minimum. The Battery-on
Indicator (VBATON) can be routed to PC4. This
signal indicates when the V has dropped below
CC
V
.
STBY
PSD Chip Select Input (CSI, PD2)
PD2 of Port D can be configured in PSDsoft Ex-
press as PSD Chip Select Input (CSI). When Low,
the signal selects and enables the internal Flash
memory, EEPROM, SRAM, and I/O blocks for
READ or WRITE operations involving the
PSD8XXFX. A High on PSD Chip Select Input
(CSI, PD2) disables the Flash memory, EEPROM,
and SRAM, and reduces the PSD8XXFX power
consumption. However, the PLD and I/O signals
remain operational when PSD Chip Select Input
(CSI, PD2) is High.
Input Control Signals
The PSD8XXFX provides the option to turn off the
input control signals (CNTL0, CNTL1, CNTL2, Ad-
dress Strobe (ALE/AS, PD0) and DBE) to the PLD
to save AC power consumption. These control sig-
nals are inputs to the PLD AND Array. During
Power-down mode, or, if any of them are not being
used as part of the PLD logic equation, these con-
trol signals should be disabled to save AC power.
They are disconnected from the PLD AND Array
by setting bits 2, 3, 4, 5, and 6 to a 1 in PMMR2.
Table 32. APD Counter Operation
APD Enable Bit ALE PD Polarity
ALE Level
APD Counter
Not Counting
0
1
1
1
X
X
1
0
X
Pulsing
Not Counting
1
0
Counting (Generates PDN after 15 Clocks)
Counting (Generates PDN after 15 Clocks)
62/103
PSD81XFX, PSD83XF2, PSD85XF2
RESET TIMING AND DEVICE STATUS AT RESET
Upon Power-up, the PSD8XXFX requires a Reset
device is operational after warm reset. Figure 31
shows the timing of the Power-up and warm reset.
(RESET) pulse of duration t
after V
is
NLNH-PO
CC
steady. During this period, the device loads inter-
nal configurations, clears some of the registers
and sets the Flash memory into Operating mode.
After the rising edge of Reset (RESET), the
PSD8XXFX remains in the Reset mode for an ad-
I/O Pin, Register and PLD Status at Reset
Table 33 shows the I/O pin, register and PLD sta-
tus during Power On Reset, warm reset and Pow-
er-down mode. PLD outputs are always valid
during warm reset, and they are valid in Power On
Reset once the internal PSD8XXFX Configuration
bits are loaded. This loading of PSD8XXFX is
ditional period, t
cess is allowed.
, before the first memory ac-
OPR
The Flash memory is reset to the READ Mode
upon Power-up. Sector Select (FS0-FS7 and
CSBOOT0-CSBOOT3) must all be Low, Write
Strobe (WR, CNTL0) High, during Power On Re-
set for maximum security of the data contents and
to remove the possibility of a byte being written on
the first edge of Write Strobe (WR, CNTL0). Any
Flash memory WRITE cycle initiation is prevented
completed typically long before the V ramps up
CC
to operating level. Once the PLD is active, the
state of the outputs are determined by the PSDa-
bel equations.
Reset of Flash Memory Erase and Program
Cycles (on the PSD834Fx)
A Reset (RESET) also resets the internal Flash
memory state machine. During a Flash memory
Program or Erase cycle, Reset (RESET) termi-
nates the cycle and returns the Flash memory to
automatically when V is below V
.
CC
LKO
Warm Reset
Once the device is up and running, the device can
be reset with a pulse of a much shorter duration,
the Read Mode within a period of t
.
NLNH-A
t
. The same t
period is needed before the
NLNH
OPR
Figure 31. Reset (RESET) Timing
VCC(min)
V
CC
t
NLNH
t
t
OPR
t
t
NLNH-PO
NLNH-A
OPR
Power-On Reset
Warm Reset
RESET
AI02866b
63/103
PSD81XFX, PSD83XF2, PSD85XF2
Table 33. Status During Power-On Reset, Warm Reset and Power-down Mode
Port Configuration
MCU I/O
Power-On Reset
Input mode
Warm Reset
Input mode
Power-down Mode
Unchanged
Valid after internal PSD
configuration bits are
loaded
Depends on inputs to PLD
(addresses are blocked in
PD mode)
PLD Output
Valid
Address Out
Data Port
Tri-stated
Tri-stated
Tri-stated
Tri-stated
Tri-stated
Tri-stated
Not defined
Tri-stated
Tri-stated
Peripheral I/O
Register
Power-On Reset
Warm Reset
Power-down Mode
PMMR0 and PMMR2
Cleared to 0
Unchanged
Unchanged
Cleared to 0 by internal
Power-On Reset
Depends on .re and .pr
equations
Depends on .re and .pr
equations
Macrocells flip-flop status
Initialized, based on the
selection in PSDsoft
Configuration menu
Initialized, based on the
selection in PSDsoft
Configuration menu
1
Unchanged
Unchanged
VM Register
All other registers
Cleared to 0
Cleared to 0
Note: 1. The SR_cod and PeriphMode bits in the VM Register are always cleared to 0 on Power-On Reset or Warm Reset.
64/103
PSD81XFX, PSD83XF2, PSD85XF2
PROGRAMMING IN-CIRCUIT USING THE JTAG SERIAL INTERFACE
The JTAG Serial Interface block can be enabled
on Port C (see Table 34). All memory blocks (pri-
mary and secondary Flash memory), PLD logic,
and PSD8XXFX Configuration Register bits may
be programmed through the JTAG Serial Interface
block. A blank device can be mounted on a printed
circuit board and programmed using JTAG.
The standard JTAG signals (IEEE 1149.1) are
TMS, TCK, TDI, and TDO. Two additional signals,
TSTAT and TERR, are optional JTAG extensions
used to speed up Program and Erase cycles.
By default, on a blank PSD8XXFX (as shipped
from the factory or after erasure), four pins on Port
C are enabled for the basic JTAG signals TMS,
TCK, TDI, and TDO.
See Application Note AN1153 for more details on
JTAG In-System Programming (ISP).
JTAG_ENABLE bit in this register
will enable the pins for JTAG use.
This bit is cleared by a PSD reset
or the microcontroller. See Table
35 for bit definition. */
PSD_product_term_enabled;
/* A dedicated product term (PT)
inside the PSD can be used to en-
able the JTAG pins. This PT has
the reserved name JTAGSEL. Once
defined as a node in PSDabel, the
designer can write an equation for
JTAGSEL. This method is used when
the Port C JTAG pins are multi-
plexed with other I/O signals. It
is recommended to logically tie
the node JTAGSEL to the JEN\ sig-
nal on the Flashlink cable when
multiplexing JTAG signals. See Ap-
plication Note 1153 for details.
*/
Standard JTAG Signals
The standard JTAG signals (TMS, TCK, TDI, and
TDO) can be enabled by any of three different con-
ditions that are logically ORed. When enabled,
TDI, TDO, TCK, and TMS are inputs, waiting for a
JTAG serial command from an external JTAG con-
troller device (such as FlashLINK or Automated
Test Equipment). When the enabling command is
received, TDO becomes an output and the JTAG
channel is fully functional inside the PSD8XXFX.
The same command that enables the JTAG chan-
nel may optionally enable the two additional JTAG
signals, TSTAT and TERR.
The following symbolic logic equation specifies the
conditions enabling the four basic JTAG signals
(TMS, TCK, TDI, and TDO) on their respective
Port C pins. For purposes of discussion, the logic
label JTAG_ON is used. When JTAG_ON is true,
the four pins are enabled for JTAG. When
JTAG_ON is false, the four pins can be used for
general PSD8XXFX I/O.
The state of the PSD Reset (RESET) signal does
not interrupt (or prevent) JTAG operations if the
JTAG pins are dedicated by an NVM configuration
bit (via PSDsoft Express). However, Reset (RE-
SET) will prevent or interrupt JTAG operations if
the JTAG enable register is used to enable the
JTAG pins.
The PSD8XXFX supports JTAG In-System-Con-
figuration (ISC) commands, but not Boundary
Scan. The PSDsoft Express software tool and
FlashLINK JTAG programming cable implement
the JTAG In-System-Configuration (ISC) com-
mands. A definition of these JTAG In-System-
Configuration (ISC) commands and sequences is
defined in a supplemental document available
from ST. This document is needed only as a refer-
ence for designers who use a FlashLINK to pro-
gram their PSD8XXFX.
JTAG_ON = PSDsoft_enabled +
/* An NVM configuration bit inside
the PSD is set by the designer in
the PSDsoft Express Configuration
utility. This dedicates the pins
for JTAG at all times (compliant
with IEEE 1149.1 */
Table 34. JTAG Port Signals
Port C Pin
PC0
JTAG Signals
TMS
Description
Mode Select
PC1
PC3
PC4
PC5
PC6
TCK
Clock
Microcontroller_enabled +
TSTAT
TERR
TDI
Status
/* The microcontroller can set a
bit at run-time by writing to the
PSD register, JTAG Enable. This
register is located at address
CSIOP + offset C7h. Setting the
Error Flag
Serial Data In
Serial Data Out
TDO
65/103
PSD81XFX, PSD83XF2, PSD85XF2
JTAG Extensions
TSTAT and TERR are two JTAG extension signals
enabled by an “ISC_ENABLE” command received
over the four standard JTAG signals (TMS, TCK,
TDI, and TDO). They are used to speed Program
and Erase cycles by indicating status on
PSD8XXFX signals instead of having to scan the
status out serially using the standard JTAG chan-
nel. See Application Note AN1153.
TERR indicates if an error has occurred when
erasing a sector or programming a byte in Flash
memory. This signal goes Low (active) when an
Error condition occurs, and stays Low until an
“ISC_CLEAR” command is executed or a chip Re-
set (RESET) pulse is received after an
“ISC_DISABLE” command.
TSTAT behaves the same as Ready/Busy de-
scribed in the section entitled “Ready/Busy (PC3)”,
on page 18. TSTAT is High when the PSD8XXFX
device is in READ Mode (primary and secondary
Flash memory contents can be read). TSTAT is
Low when Flash memory Program or Erase cycles
are in progress, and also when data is being writ-
ten to the secondary Flash memory.
TSTAT and TERR can be configured as open-
drain type signals during an “ISC_ENABLE” com-
mand. This facilitates a wired-OR connection of
TSTAT signals from multiple PSD8XXFX devices
and a wired-OR connection of TERR signals from
those same devices. This is useful when several
PSD8XXFX devices are “chained” together in a
JTAG environment.
Security and Flash memory Protection
When the security bit is set, the device cannot be
read on a Device Programmer or through the
JTAG Port. When using the JTAG Port, only a Full
Chip Erase command is allowed.
All other Program, Erase and Verify commands
are blocked. Full Chip Erase returns the part to a
non-secured blank state. The Security Bit can be
set in PSDsoft Express Configuration.
All primary and secondary Flash memory sectors
can individually be sector protected against era-
sures. The sector protect bits can be set in PSD-
soft Express Configuration.
INITIAL DELIVERY STATE
When delivered from ST, the PSD8XXFX device
has all bits in the memory and PLDs set to 1. The
PSD8XXFX Configuration Register bits are set to
0. The code, configuration, and PLD logic are
loaded using the programming procedure. Infor-
mation for programming the device is available di-
rectly from ST. Please contact your local sales
representative.
Table 35. JTAG Enable Register
0 = off JTAG port is disabled.
Bit 0
JTAG_Enable
1 = on JTAG port is enabled.
Bit 1
Bit 2
Bit 3
Bit 4
Bit 5
Bit 6
Bit 7
X
X
X
X
X
X
X
0
0
0
0
0
0
0
Not used, and should be set to zero.
Not used, and should be set to zero.
Not used, and should be set to zero.
Not used, and should be set to zero.
Not used, and should be set to zero.
Not used, and should be set to zero.
Not used, and should be set to zero.
Note: 1. The state of Reset (RESET) does not interrupt (or prevent) JTAG operations if the JTAG signals are dedicated by an NVM Config-
uration bit (via PSDsoft Express). However, Reset (RESET) prevents or interrupts JTAG operations if the JTAG enable register is
used to enable the JTAG signals.
66/103
PSD81XFX, PSD83XF2, PSD85XF2
AC/DC PARAMETERS
These tables describe the AD and DC parameters
of the PSD8XXFX:
The following are issues concerning the parame-
ters presented:
❏ DC Electrical Specification
❏ AC Timing Specification
■ PLD Timing
■ In the DC specification the supply current is
given for different modes of operation. Before
calculating the total power consumption,
determine the percentage of time that the
PSD8XXFX is in each mode. Also, the supply
power is considerably different if the Turbo bit is
0.
■ The AC power component gives the PLD, Flash
memory, and SRAM mA/MHz specification.
Figure 32 and Figure 33 show the PLD mA/MHz
as a function of the number of Product Terms
(PT) used.
– Combinatorial Timing
– Synchronous Clock Mode
– Asynchronous Clock Mode
– Input Macrocell Timing
■ MCU Timing
– READ Timing
– WRITE Timing
■ In the PLD timing parameters, add the required
– Peripheral Mode Timing
– Power-down and Reset Timing
delay when Turbo bit is 0.
Figure 32. PLD I /Frequency Consumption (5 V range)
CC
110
100
90
V
CC
= 5V
80
70
60
50
40
30
20
10
0
PT 100%
PT 25%
0
5
10
15
20
25
HIGHEST COMPOSITE FREQUENCY AT PLD INPUTS (MHz)
AI02894
67/103
PSD81XFX, PSD83XF2, PSD85XF2
Figure 33. PLD I /Frequency Consumption (3 V range)
CC
60
V
CC
= 3V
50
40
30
20
10
0
PT 100%
PT 25%
0
5
10
15
20
25
HIGHEST COMPOSITE FREQUENCY AT PLD INPUTS (MHz)
AI03100
68/103
PSD81XFX, PSD83XF2, PSD85XF2
Table 36. Example of PSD8XXFX Typical Power Calculation at V = 5.0 V (Turbo Mode On)
CC
Conditions
Highest Composite PLD input frequency
(Freq PLD)
= 8 MHz
= 4 MHz
MCU ALE frequency (Freq ALE)
% Flash memory
Access
= 80%
% SRAM access
% I/O access
= 15%
= 5% (no additional power above base)
Operational Modes
% Normal
= 10%
= 90%
% Power-down Mode
Number of product terms used
(from fitter report)
= 45 PT
% of total product terms = 45/182 = 24.7%
Turbo Mode
= ON
Calculation (using typical values)
I
total
= Ipwrdown x %pwrdown + %normal x (I (ac) + I
(dc))
CC
CC
CC
= Ipwrdown x %pwrdown + % normal x (%flash x 2.5 mA/MHz x Freq ALE
+ %SRAM x 1.5 mA/MHz x Freq ALE
+ % PLD x 2 mA/MHz x Freq PLD
+ #PT x 400 µA/PT)
= 50 µA x 0.90 + 0.1 x (0.8 x 2.5 mA/MHz x 4 MHz
+ 0.15 x 1.5 mA/MHz x 4 MHz
+ 2 mA/MHz x 8 MHz
+ 45 x 0.4 mA/PT)
= 45 µA + 0.1 x (8 + 0.9 + 16 + 18 mA)
= 45 µA + 0.1 x 42.9
= 45 µA + 4.29 mA
= 4.34 mA
This is the operating power with no EEPROM WRITE or Flash memory Erase cycles in progress. Calculation is based
on I
= 0 mA.
OUT
69/103
PSD81XFX, PSD83XF2, PSD85XF2
Table 37. Example of PSD8XXFX Typical Power Calculation at V = 5.0 V (Turbo Mode Off)
CC
Conditions
Highest Composite PLD input frequency
(Freq PLD)
= 8 MHz
= 4 MHz
MCU ALE frequency (Freq ALE)
% Flash memory
Access
= 80%
% SRAM access
% I/O access
= 15%
= 5% (no additional power above base)
Operational Modes
% Normal
= 10%
= 90%
% Power-down Mode
Number of product terms used
(from fitter report)
= 45 PT
% of total product terms = 45/182 = 24.7%
Turbo Mode
= Off
Calculation (using typical values)
I
total
= Ipwrdown x %pwrdown + %normal x (I (ac) + I
(dc))
CC
CC
CC
= Ipwrdown x %pwrdown + % normal x (%flash x 2.5 mA/MHz x Freq ALE
+ %SRAM x 1.5 mA/MHz x Freq ALE
+ % PLD x (from graph using Freq PLD))
= 50 µA x 0.90 + 0.1 x (0.8 x 2.5 mA/MHz x 4 MHz
+ 0.15 x 1.5 mA/MHz x 4 MHz
+ 24 mA)
= 45 µA + 0.1 x (8 + 0.9 + 24)
= 45 µA + 0.1 x 32.9
= 45 µA + 3.29 mA
= 3.34 mA
This is the operating power with no EEPROM WRITE or Flash memory Erase cycles in progress. Calculation is based
on I
= 0 mA.
OUT
70/103
PSD81XFX, PSD83XF2, PSD85XF2
MAXIMUM RATING
Stressing the device above the rating listed in the
Absolute Maximum Ratings” table may cause per-
manent damage to the device. These are stress
ratings only and operation of the device at these or
any other conditions above those indicated in the
Operating sections of this specification is not im-
plied. Exposure to Absolute Maximum Rating con-
ditions for extended periods may affect device
reliability. Refer also to the STMicroelectronics
SURE Program and other relevant quality docu-
ments.
Table 38. Absolute Maximum Ratings
Symbol
Parameter
Min.
Max.
125
235
7.0
Unit
°C
°C
V
T
Storage Temperature
–65
STG
1
TLEAD
VIO
Lead Temperature during Soldering (20 seconds max.)
Input and Output Voltage (Q = V or Hi-Z)
–0.6
–0.6
OH
V
CC
Supply Voltage
7.0
V
V
Device Programmer Supply Voltage
–0.6
14.0
2000
V
PP
2
VESD
–2000
V
Electrostatic Discharge Voltage (Human Body model)
Note: 1. IPC/JEDEC J-STD-020A
2. JEDEC Std JESD22-A114A (C1=100 pF, R1=1500 Ω, R2=500 Ω)
71/103
PSD81XFX, PSD83XF2, PSD85XF2
DC AND AC PARAMETERS
This section summarizes the operating and mea-
surement conditions, and the DC and AC charac-
teristics of the device. The parameters in the DC
and AC Characteristic tables that follow are de-
rived from tests performed under the Measure-
ment Conditions summarized in the relevant
tables. Designers should check that the operating
conditions in their circuit match the measurement
conditions when relying on the quoted parame-
ters.
Table 39. Operating Conditions (5V devices)
Symbol
Parameter
Min.
4.5
–40
0
Max.
5.5
85
Unit
V
V
CC
Supply Voltage
Ambient Operating Temperature (industrial)
Ambient Operating Temperature (commercial)
°C
°C
TA
70
Table 40. Operating Conditions (3V devices)
Symbol
Parameter
Min.
3.0
–40
0
Max.
3.6
85
Unit
V
V
CC
Supply Voltage
Ambient Operating Temperature (industrial)
Ambient Operating Temperature (commercial)
°C
°C
TA
70
Table 41. AC Measurement Conditions
Symbol
Parameter
Min.
Max.
Unit
C
Load Capacitance
30
pF
L
Note: 1. Output Hi-Z is defined as the point where data out is no longer driven.
Figure 34. AC Measurement I/O Waveform
Figure 35. AC Measurement Load Circuit
2.01 V
3.0V
195 Ω
Test Point
1.5V
Device
Under Test
0V
CL = 30 pF
(Including Scope and
AI03103b
Jig Capacitance)
AI03104b
Table 42. Capacitance
Symbol
2
Parameter
Test Condition
Max.
Unit
pF
Typ.
C
V
= 0V
= 0V
Input Capacitance (for input pins)
4
6
IN
IN
Output Capacitance (for input/
output pins)
pF
C
V
OUT
8
12
25
OUT
C
VPP
Capacitance (for CNTL2/V
)
PP
V = 0V
PP
pF
18
Note: 1. Sampled only, not 100% tested.
2. Typical values are for T = 25°C and nominal supply voltages.
A
72/103
PSD81XFX, PSD83XF2, PSD85XF2
Table 43. AC Symbols for PLD Timing
Signal Letters
Signal Behavior
A
C
D
E
G
I
Address Input
t
Time
CEout Output
L
Logic Level Low or ALE
Logic Level High
Valid
Input Data
H
V
X
Z
E Input
Internal WDOG_ON signal
Interrupt Input
No Longer a Valid Logic Level
Float
L
ALE Input
PW Pulse Width
N
P
Q
R
S
T
Reset Input or Output
Port Signal Output
Output Data
WR, UDS, LDS, DS, IORD, PSEN Inputs
Chip Select Input
R/W Input
W
B
M
Internal PDN Signal
V
STBY
Output
Output Macrocell
Example: t
– Time from Address Valid to ALE Invalid.
AVLX
Figure 36. Switching Waveforms – Key
INPUTS
OUTPUTS
WAVEFORMS
STEADY INPUT
STEADY OUTPUT
MAY CHANGE FROM
HI TO LO
WILL BE CHANGING
FROM HI TO LO
MAY CHANGE FROM
LO TO HI
WILL BE CHANGING
LO TO HI
DON'T CARE
CHANGING, STATE
UNKNOWN
OUTPUTS ONLY
CENTER LINE IS
TRI-STATE
AI03102
73/103
PSD81XFX, PSD83XF2, PSD85XF2
Table 44. DC Characteristics (5V devices)
Test Condition
Symbol
Parameter
(in addition to those in
Table 39)
Min.
Typ.
Max.
+0.5
Unit
V
4.5 V < V < 5.5 V
V
V
Input High Voltage
2
V
V
V
IH
CC
CC
V
V
V
V
4.5 V < V < 5.5 V
Input Low Voltage
–0.5
0.8
+0.5
IL
CC
1
0.8V
Reset High Level Input Voltage
IH1
CC
CC
(Note )
1
0.2V –0.1
Reset Low Level Input Voltage
Reset Pin Hysteresis
–0.5
0.3
V
V
IL1
CC
(Note )
HYS
V
(min) for Flash Erase and
CC
V
V
2.5
4.2
V
LKO
OL
Program
I
= 20 µA, V = 4.5 V
0.01
0.25
4.49
3.9
0.1
V
V
OL
CC
Output Low Voltage
I
= 8 mA, V = 4.5 V
0.45
OL
CC
I
= –20 µA, V = 4.5 V
4.4
2.4
V
OH
CC
Output High Voltage Except
V
OH
V
STBY
On
I
= –2 mA, V = 4.5 V
V
OH
CC
V
V
I
Output High Voltage V
On
I
= 1 µA
V
– 0.8
STBY
V
OH1
STBY
OH1
V
SRAM Stand-by Voltage
SRAM Stand-by Current
2.0
V
STBY
CC
V
= 0 V
0.5
1
µA
µA
V
STBY
IDLE
CC
I
Idle Current (V
input)
V
> V
CC STBY
–0.1
2
0.1
STBY
V
I
Only on V
SRAM Data Retention Voltage
DF
STBY
–0.3 V (Notes
< V < V
Stand-by Supply Current
for Power-down Mode
2,3
50
200
µA
SB
CSI >V
V
)
CC
I
I
Input Leakage Current
Output Leakage Current
–1
±0.1
±5
1
µA
µA
LI
SS
IN
CC
0.45 < V
< V
CC
–10
10
LO
OUT
PLD_TURBO = Off,
0
µA/PT
µA/PT
mA
5
f = 0 MHz (Note )
PLD Only
PLD_TURBO = On,
f = 0 MHz
400
15
700
30
Operating
Supply
Current
I
(DC)
5
CC
During Flash memory
WRITE/Erase Only
(Note )
Flash memory
Read only, f = 0 MHz
f = 0 MHz
0
0
0
0
mA
mA
SRAM
4
PLD AC Adder
note
mA/
MHz
I
(AC)
5
CC
Flash memory AC Adder
SRAM AC Adder
2.5
1.5
3.5
3.0
(Note )
mA/
MHz
Note: 1. Reset (RESET) has hysteresis. V is valid at or below 0.2V –0.1. V
is valid at or above 0.8V
.
CC
IL1
CC
IH1
2. CSI deselected or internal Power-down mode is active.
3. PLD is in non-Turbo mode, and none of the inputs are switching.
4. Please see Figure 32 for the PLD current calculation.
5. I
= 0 mA
OUT
74/103
PSD81XFX, PSD83XF2, PSD85XF2
Table 45. DC Characteristics (3V devices)
Symbol
Parameter
Conditions
Min.
0.7V
Typ.
Max.
+0.5
CC
Unit
V
V
3.0 V < V < 3.6 V
V
High Level Input Voltage
Low Level Input Voltage
Reset High Level Input Voltage
IH
CC
CC
V
V
V
V
3.0 V < V < 3.6 V
–0.5
0.8V
0.8
+0.5
V
IL
CC
1
V
V
IH1
CC
CC
(Note )
1
0.2V –0.1
Reset Low Level Input Voltage
Reset Pin Hysteresis
–0.5
0.3
V
V
IL1
CC
(Note )
HYS
V
(min) for Flash Erase and
CC
V
V
1.5
2.2
V
LKO
OL
Program
I
= 20 µA, V = 3.0 V
0.01
0.15
2.99
2.8
0.1
V
V
OL
CC
Output Low Voltage
I
= 4 mA, V = 3.0 V
0.45
OL
CC
I
= –20 µA, V = 3.0 V
2.9
2.7
V
OH
CC
Output High Voltage Except
V
OH
V
STBY
On
I
= –1 mA, V = 3.0 V
V
OH
CC
V
V
I
Output High Voltage V
On
I
= 1 µA
V
– 0.8
STBY
V
OH1
STBY
OH1
V
SRAM Stand-by Voltage
SRAM Stand-by Current
2.0
V
STBY
CC
V
= 0 V
0.5
1
µA
µA
V
STBY
IDLE
CC
I
Idle Current (V
input)
V
> V
CC STBY
–0.1
2
0.1
STBY
V
I
Only on V
SRAM Data Retention Voltage
DF
STBY
–0.3 V (Notes
< V < V
Stand-by Supply Current
for Power-down Mode
2,3
25
100
µA
CSI >V
V
)
SB
CC
I
I
Input Leakage Current
Output Leakage Current
–1
±0.1
±5
1
µA
µA
LI
SS
IN
CC
0.45 < V < V
CC
–10
10
LO
IN
PLD_TURBO = Off,
0
µA/PT
µA/PT
mA
3
f = 0 MHz (Note )
PLD Only
PLD_TURBO = On,
f = 0 MHz
200
10
400
25
Operating
Supply
Current
I
(DC)
5
CC
During Flash memory
WRITE/Erase Only
(Note )
Flash memory
Read only, f = 0 MHz
f = 0 MHz
0
0
0
0
mA
mA
SRAM
4
PLD AC Adder
note
1.5
mA/
MHz
I
(AC)
5
CC
Flash memory AC Adder
SRAM AC Adder
2.0
1.5
(Note )
mA/
MHz
0.8
Note: 1. Reset (RESET) has hysteresis. V is valid at or below 0.2V –0.1. V
is valid at or above 0.8V
.
CC
IL1
CC
IH1
2. CSI deselected or internal PD is active.
3. PLD is in non-Turbo mode, and none of the inputs are switching.
4. Please see Figure 33 for the PLD current calculation.
5. I
= 0 mA
OUT
75/103
PSD81XFX, PSD83XF2, PSD85XF2
Figure 37. Input to Output Disable / Enable
INPUT
tER
tEA
INPUT TO
OUTPUT
ENABLE/DISABLE
AI02863
Table 46. CPLD Combinatorial Timing (5V devices)
-70
-90
-15
Fast
PT
Aloc
Slew
Turbo
Off
Symbol
Parameter
Conditions
Unit
1
rate
Min Max Min Max Min Max
CPLD Input Pin/
Feedback to CPLD
Combinatorial Output
t
20
25
32
+ 2
+ 10
– 2
ns
PD
CPLD Input to CPLD
Output Enable
t
t
t
t
t
21
21
21
26
26
26
32
32
33
+ 10
+ 10
+ 10
+ 10
– 2
– 2
– 2
ns
ns
ns
ns
ns
EA
CPLD Input to CPLD
Output Disable
ER
CPLD Register Clear
or Preset Delay
ARP
ARPW
ARD
CPLD Register Clear
or Preset Pulse Width
10
20
29
Any
macrocell
CPLD Array Delay
11
16
22
+ 2
Note: 1. Fast Slew Rate output available on PA3-PA0, PB3-PB0, and PD2-PD0. Decrement times by given amount.
Table 47. CPLD Combinatorial Timing (3V devices)
-12
-15
-20
Slew
PT Turbo
Symbol
Parameter
Conditions
Unit
1
Aloc
Off
rate
Min Max Min Max Min Max
CPLD Input Pin/
t
Feedback to CPLD
Combinatorial Output
40
45
50
+ 4
+ 20
– 6
ns
PD
CPLD Input to CPLD
Output Enable
t
t
43
43
45
45
50
50
+ 20
+ 20
– 6
– 6
ns
ns
EA
ER
CPLD Input to CPLD
Output Disable
CPLD Register Clear
or
Preset Delay
t
40
43
48
+ 20
+ 20
– 6
ns
ARP
CPLD Register Clear
or
Preset Pulse Width
t
t
25
30
35
ns
ns
ARPW
ARD
Any
macrocell
CPLD Array Delay
25
29
33
+ 4
Note: 1. Fast Slew Rate output available on PA3-PA0, PB3-PB0, and PD2-PD0. Decrement times by given amount.
76/103
PSD81XFX, PSD83XF2, PSD85XF2
Figure 38. Synchronous Clock Mode Timing – PLD
t
t
CL
CH
CLKIN
INPUT
t
S
t
H
t
CO
REGISTERED
OUTPUT
AI02860
Table 48. CPLD Macrocell Synchronous Clock Mode Timing (5V devices)
-70
-90
-15
Fast
PT
Aloc
Slew
Turbo
Off
Symbol
Parameter
Conditions
Unit
1
rate
Min Max Min Max Min Max
Maximum
Frequency
External
1/(t +t
)
40.0
30.30
25.00
MHz
S
CO
Feedback
Maximum
Frequency
Internal
f
MAX
1/(t +t –10)
66.6
83.3
43.48
50.00
31.25
35.71
MHz
S
CO
Feedback
(f
CNT
)
Maximum
Frequency
Pipelined Data
1/(t +t
)
MHz
ns
CH CL
Input Setup
Time
t
12
15
20
+ 2
+ 10
S
t
t
t
Input Hold Time
Clock High Time
Clock Low Time
0
6
6
0
0
ns
ns
ns
H
Clock Input
Clock Input
10
10
15
15
CH
CL
Clock to Output
Delay
t
t
t
Clock Input
13
11
18
16
22
22
– 2
ns
ns
ns
CO
CPLD Array
Delay
Any macrocell
+ 2
ARD
Minimum Clock
t +t
CH CL
12
20
30
MIN
2
Period
Note: 1. Fast Slew Rate output available on PA3-PA0, PB3-PB0, and PD2-PD0. Decrement times by given amount.
2. CLKIN (PD1) t = t + t
.
CL
CLCL
CH
77/103
PSD81XFX, PSD83XF2, PSD85XF2
Table 49. CPLD Macrocell Synchronous Clock Mode Timing (3V devices)
-12
-15
-20
Slew
PT
Aloc
Turbo
Off
Symbol
Parameter
Conditions
Unit
1
rate
Min Max Min Max Min Max
Maximum
Frequency
1/(t +t
)
22.2
28.5
40.0
18.8
23.2
33.3
15.8
18.8
31.2
MHz
S
CO
External Feedback
Maximum
Frequency
Internal Feedback
f
1/(t +t –10)
S CO
MHz
MHz
MAX
(f
CNT
)
Maximum
Frequency
Pipelined Data
1/(t +t
)
CH CL
t
t
t
t
Input Setup Time
Input Hold Time
Clock High Time
Clock Low Time
20
0
25
0
30
0
+ 4
+ 20
ns
ns
ns
ns
S
H
Clock Input
Clock Input
15
10
15
15
16
16
CH
CL
Clock to Output
Delay
t
t
t
Clock Input
25
25
28
29
33
33
– 6
ns
ns
ns
CO
CPLD Array Delay
Any macrocell
+ 4
ARD
MIN
Minimum Clock
t +t
CH CL
25
29
32
2
Period
Note: 1. Fast Slew Rate output available on PA3-PA0, PB3-PB0, and PD2-PD0. Decrement times by given amount.
2. CLKIN (PD1) t = t + t
.
CL
CLCL
CH
78/103
PSD81XFX, PSD83XF2, PSD85XF2
Figure 39. Asynchronous Reset / Preset
tARPW
RESET/PRESET
INPUT
tARP
REGISTER
OUTPUT
AI02864
Figure 40. Asynchronous Clock Mode Timing (product term clock)
tCHA
tCLA
CLOCK
INPUT
tSA
tHA
tCOA
REGISTERED
OUTPUT
AI02859
79/103
PSD81XFX, PSD83XF2, PSD85XF2
Table 50. CPLD Macrocell Asynchronous Clock Mode Timing (5V devices)
-70
-90
-15
PT Turbo Slew
Symbol
Parameter
Conditions
Unit
Aloc
Off
Rate
Min Max Min Max Min Max
Maximum
Frequency
External
1/(t +t
)
38.4
62.5
71.4
26.32
35.71
41.67
21.27
27.78
35.71
MHz
SA COA
Feedback
Maximum
Frequency
Internal
f
1/(t +t
–10)
MHz
MHz
MAXA
SA COA
Feedback
(f
CNTA
)
Maximum
Frequency
Pipelined
Data
1/(t
+t
)
CHA CLA
Input Setup
Time
t
t
t
t
t
t
t
7
8
9
9
8
12
14
15
15
+ 2
+ 10
ns
ns
ns
ns
ns
ns
ns
SA
Input Hold
Time
12
12
12
HA
Clock Input
High Time
+ 10
+ 10
+ 10
CHA
CLA
COA
ARDA
MINA
Clock Input
Low Time
Clock to
Output Delay
21
11
30
16
37
22
– 2
CPLD Array
Delay
Any macrocell
+ 2
Minimum
Clock Period
1/f
CNTA
16
28
39
80/103
PSD81XFX, PSD83XF2, PSD85XF2
Table 51. CPLD Macrocell Asynchronous Clock Mode Timing (3V devices)
-12
-15
-20
PT Turbo Slew
Symbol
Parameter
Conditions
Unit
Aloc
Off
Rate
Min Max Min Max Min Max
Maximum
Frequency
External
1/(t +t
)
21.7
19.2
16.9
MHz
SA COA
Feedback
Maximum
Frequency
Internal
f
MAXA
1/(t +t
–10)
27.8
33.3
23.8
27
20.4
24.4
MHz
SA COA
Feedback
(f
CNTA
)
Maximum
Frequency
Pipelined Data
1/(t
+t
)
MHz
ns
CHA CLA
Input Setup
Time
t
10
12
13
+ 4
+ 20
SA
t
t
t
Input Hold Time
Clock High Time
Clock Low Time
12
17
13
15
22
15
17
25
16
ns
ns
ns
HA
+ 20
+ 20
CHA
CLA
Clock to Output
Delay
t
t
t
36
25
40
29
46
33
+ 20
– 6
ns
ns
ns
COA
ARD
MINA
CPLD Array
Delay
Any macrocell
+ 4
Minimum Clock
Period
1/f
36
42
49
CNTA
81/103
PSD81XFX, PSD83XF2, PSD85XF2
Figure 41. Input Macrocell Timing (product term clock)
t
t
INL
INH
PT CLOCK
INPUT
t
t
IH
IS
OUTPUT
t
INO
AI03101
Table 52. Input Macrocell Timing (5V devices)
-70
-90
-15
PT
Aloc
Turbo
Off
Symbol
Parameter
Conditions
Unit
Min Max Min Max Min Max
1
t
Input Setup Time
Input Hold Time
0
15
9
0
0
ns
ns
ns
ns
IS
(Note )
1
t
t
t
20
12
12
26
18
18
+ 10
IH
(Note )
1
NIB Input High Time
NIB Input Low Time
INH
INL
(Note )
1
9
(Note )
NIB Input to Combinatorial
Delay
1
t
34
46
59
+ 2
+ 10
ns
INO
(Note )
Note: 1. Inputs from Port A, B, and C relative to register/ latch clock from the PLD. ALE/AS latch timings refer to t
and t
.
LXAX
AVLX
Table 53. Input Macrocell Timing (3V devices)
-12
-15
-20
PT
Aloc
Turbo
Off
Symbol
Parameter
Conditions
Unit
Min Max Min Max Min Max
1
t
Input Setup Time
Input Hold Time
0
0
0
ns
ns
ns
ns
IS
(Note )
1
t
t
t
25
12
12
25
13
13
30
15
15
+ 20
IH
(Note )
1
NIB Input High Time
NIB Input Low Time
INH
INL
(Note )
1
(Note )
NIB Input to Combinatorial
Delay
1
t
46
62
70
+ 4
+ 20
ns
INO
(Note )
Note: 1. Inputs from Port A, B, and C relative to register/latch clock from the PLD. ALE latch timings refer to t
and t
.
LXAX
AVLX
82/103
PSD81XFX, PSD83XF2, PSD85XF2
Figure 42. READ Timing
1
t
LXAX
t
AVLX
ALE/AS
t
LVLX
A/D
MULTIPLEXED
BUS
ADDRESS
VALID
DATA
VALID
t
AVQV
ADDRESS
NON-MULTIPLEXED
BUS
ADDRESS
VALID
DATA
NON-MULTIPLEXED
BUS
DATA
VALID
t
SLQV
CSI
t
t
RLQV
t
RHQX
RLRH
RD
(PSEN, DS)
tRHQZ
t
EHEL
E
t
THEH
t
ELTL
R/W
t
AVPV
ADDRESS OUT
AI02895
Note: 1. t
and t
are not required for 80C251 in Page Mode or 80C51XA in Burst Mode.
LXAX
AVLX
83/103
PSD81XFX, PSD83XF2, PSD85XF2
Table 54. READ Timing (5V devices)
-70
-90
-15
Turbo
Off
Symbol
Parameter
Conditions
Unit
Min Max Min Max Min Max
t
ALE or AS Pulse Width
Address Setup Time
15
4
20
6
28
10
11
ns
ns
ns
ns
ns
ns
LVLX
AVLX
LXAX
AVQV
SLQV
3
t
t
t
t
(Note )
3
Address Hold Time
7
8
(Note )
3
Address Valid to Data Valid
CS Valid to Data Valid
RD to Data Valid 8-Bit Bus
70
75
24
90
100
32
150 + 10
(Note )
150
40
5
(Note )
t
RLQV
RD or PSEN to Data Valid
8-Bit Bus, 8031, 80251
2
31
38
45
30
ns
(Note )
1
t
t
RD Data Hold Time
RD Pulse Width
0
0
0
ns
ns
RHQX
RLRH
(Note )
1
27
32
38
(Note )
1
t
t
t
t
RD to Data High-Z
20
25
ns
ns
ns
ns
RHQZ
EHEL
THEH
ELTL
(Note )
E Pulse Width
27
6
32
10
0
38
18
0
R/W Setup Time to Enable
R/W Hold Time After Enable
0
Address Input Valid to
Address Output Delay
4
t
20
25
30
ns
AVPV
(Note )
Note: 1. RD timing has the same timing as DS, LDS, UDS, and PSEN signals.
2. RD and PSEN have the same timing.
3. Any input used to select an internal PSD8XXFX function.
4. In multiplexed mode, latched addresses generated from ADIO delay to address output on any Port.
5. RD timing has the same timing as DS, LDS, and UDS signals.
84/103
PSD81XFX, PSD83XF2, PSD85XF2
Table 55. READ Timing (3V devices)
-12
-15
-20
Turbo
Off
Symbol
Parameter
Conditions
Unit
Min Max Min Max Min Max
t
ALE or AS Pulse Width
Address Setup Time
26
9
26
10
12
30
12
14
ns
ns
ns
ns
ns
ns
LVLX
AVLX
LXAX
AVQV
SLQV
3
t
t
t
t
(Note )
3
Address Hold Time
9
(Note )
3
Address Valid to Data Valid
CS Valid to Data Valid
RD to Data Valid 8-Bit Bus
120
120
35
150
150
35
200 + 20
(Note )
200
40
5
(Note )
t
RLQV
RD or PSEN to Data Valid 8-Bit Bus,
8031, 80251
2
45
50
55
ns
(Note )
1
t
t
t
t
t
t
RD Data Hold Time
RD Pulse Width
0
0
0
ns
ns
ns
ns
ns
ns
RHQX
RLRH
RHQZ
EHEL
THEH
ELTL
(Note )
38
40
45
1
RD to Data High-Z
38
40
45
(Note )
E Pulse Width
40
15
0
45
18
0
52
20
0
R/W Setup Time to Enable
R/W Hold Time After Enable
Address Input Valid to
Address Output Delay
4
t
33
35
40
ns
AVPV
(Note )
Note: 1. RD timing has the same timing as DS, LDS, UDS, and PSEN signals.
2. RD and PSEN have the same timing for 8031.
3. Any input used to select an internal PSD8XXFX function.
4. In multiplexed mode latched address generated from ADIO delay to address output on any Port.
5. RD timing has the same timing as DS, LDS, and UDS signals.
85/103
PSD81XFX, PSD83XF2, PSD85XF2
Figure 43. WRITE Timing
t
t
LXAX
AVLX
ALE/AS
t
LVLX
A/D
MULTIPLEXED
BUS
ADDRESS
VALID
DATA
VALID
t
AVWL
ADDRESS
NON-MULTIPLEXED
BUS
ADDRESS
VALID
DATA
NON-MULTIPLEXED
BUS
DATA
VALID
t
SLWL
CSI
t
t
DVWH
WHDX
t
WR
WLWH
t
WHAX
(DS)
t
EHEL
E
t
t
THEH
ELTL
R/ W
t
WLMV
t
t
AVPV
WHPV
STANDARD
MCU I/O OUT
ADDRESS OUT
AI02896
86/103
PSD81XFX, PSD83XF2, PSD85XF2
Table 56. WRITE Timing (5V devices)
-70
-90
-15
Symbol
Parameter
ALE or AS Pulse Width
Conditions
Unit
Min Max Min Max Min Max
t
15
4
20
6
28
10
11
ns
ns
ns
LVLX
AVLX
LXAX
1
t
t
Address Setup Time
Address Hold Time
(Note )
1
7
8
(Note )
Address Valid to Leading
Edge of WR
1,3
t
8
15
20
ns
AVWL
(Notes
)
3
t
t
t
t
t
CS Valid to Leading Edge of WR
WR Data Setup Time
12
25
4
15
35
5
20
45
5
ns
ns
ns
ns
ns
SLWL
(Note )
3
DVWH
WHDX
WLWH
WHAX1
(Note )
3
WR Data Hold Time
(Note )
3
WR Pulse Width
31
6
35
8
45
10
(Note )
3
Trailing Edge of WR to Address Invalid
(Note )
Trailing Edge of WR to DPLD Address
Invalid
3,6
t
t
0
0
0
ns
ns
WHAX2
WHPV
(Note
)
Trailing Edge of WR to Port Output
Valid Using I/O Port Data Register
3
27
42
30
55
38
65
(Note )
Data Valid to Port Output Valid
Using Macrocell Register
Preset/Clear
3,5
t
ns
DVMV
(Notes
)
Address Input Valid to Address
Output Delay
2
t
t
20
48
25
55
30
65
ns
ns
AVPV
(Note )
WR Valid to Port Output Valid Using
Macrocell Register Preset/Clear
3,4
WLMV
(Notes
)
Note: 1. Any input used to select an internal PSD8XXFX function.
2. In multiplexed mode, latched address generated from ADIO delay to address output on any port.
3. WR has the same timing as E, LDS, UDS, WRL, and WRH signals.
4. Assuming data is stable before active WRITE signal.
5. Assuming WRITE is active before data becomes valid.
6. TWHAX2 is the address hold time for DPLD inputs that are used to generate Sector Select signals for internal PSD8XXFX memory.
87/103
PSD81XFX, PSD83XF2, PSD85XF2
Table 57. WRITE Timing (3V devices)
-12
-15
-20
Symbol
Parameter
ALE or AS Pulse Width
Conditions
Unit
Min Max Min Max Min Max
t
26
9
26
10
12
30
12
14
LVLX
AVLX
LXAX
1
t
t
Address Setup Time
Address Hold Time
ns
ns
(Note )
1
9
(Note )
Address Valid to Leading
Edge of WR
1,3
t
17
20
25
ns
AVWL
(Notes
)
3
t
t
t
t
t
CS Valid to Leading Edge of WR
WR Data Setup Time
17
45
7
20
45
8
25
50
10
53
17
ns
ns
ns
ns
ns
SLWL
(Note )
3
DVWH
WHDX
WLWH
WHAX1
(Note )
3
WR Data Hold Time
(Note )
3
WR Pulse Width
46
10
48
12
(Note )
3
Trailing Edge of WR to Address Invalid
(Note )
Trailing Edge of WR to DPLD Address
Invalid
3,6
t
t
t
t
t
0
0
0
ns
ns
ns
ns
ns
WHAX2
WHPV
DVMV
AVPV
(Note
)
Trailing Edge of WR to Port Output
Valid Using I/O Port Data Register
3
33
70
33
70
35
70
35
70
40
80
40
80
(Note )
Data Valid to Port Output Valid
Using Macrocell Register Preset/Clear
3,5
(Notes
)
Address Input Valid to Address
Output Delay
2
(Note )
WR Valid to Port Output Valid Using
Macrocell Register Preset/Clear
3,4
WLMV
(Notes
)
Note: 1. Any input used to select an internal PSD8XXFX function.
2. In multiplexed mode, latched address generated from ADIO delay to address output on any port.
3. WR has the same timing as E, LDS, UDS, WRL, and WRH signals.
4. Assuming data is stable before active WRITE signal.
5. Assuming WRITE is active before data becomes valid.
6. TWHAX2 is the address hold time for DPLD inputs that are used to generate Sector Select signals for internal PSD8XXFX memory.
88/103
PSD81XFX, PSD83XF2, PSD85XF2
Table 58. Program, WRITE and Erase Times (5V devices)
Symbol
Parameter
Min.
Typ.
8.5
3
Max.
30
Unit
Flash Program
s
1
s
Flash Bulk Erase (pre-programmed)
Flash Bulk Erase (not pre-programmed)
Sector Erase (pre-programmed)
Sector Erase (not pre-programmed)
Byte Program
5
s
s
t
t
t
1
30
WHQV3
WHQV2
WHQV1
2.2
14
s
1200
µs
Program / Erase Cycles (per Sector)
Sector Erase Time-Out
100,000
cycles
µs
t
t
100
WHWLO
Q7VQV
2
30
ns
DQ7 Valid to Output (DQ7-DQ0) Valid (Data Polling)
Note: 1. Programmed to all zero before erase.
2. The polling status, DQ7, is valid tQ7VQV time units before the data byte, DQ0-DQ7, is valid for reading.
Table 59. Program, WRITE and Erase Times (3V devices)
Symbol
Parameter
Min.
Typ.
8.5
3
Max.
30
Unit
Flash Program
s
1
s
s
Flash Bulk Erase (pre-programmed)
Flash Bulk Erase (not pre-programmed)
Sector Erase (pre-programmed)
Sector Erase (not pre-programmed)
Byte Program
5
t
t
t
1
30
s
WHQV3
WHQV2
WHQV1
2.2
14
s
1200
µs
cycles
µs
ns
Program / Erase Cycles (per Sector)
Sector Erase Time-Out
100,000
t
t
100
WHWLO
Q7VQV
2
30
DQ7 Valid to Output (DQ7-DQ0) Valid (Data Polling)
Note: 1. Programmed to all zero before erase.
2. The polling status, DQ7, is valid tQ7VQV time units before the data byte, DQ0-DQ7, is valid for reading.
89/103
PSD81XFX, PSD83XF2, PSD85XF2
Figure 44. Peripheral I/O READ Timing
ALE/AS
ADDRESS
DATA VALID
A/D BUS
t
(PA)
(PA)
AVQV
t
SLQV
CSI
RD
t
t
(PA)
(PA)
RLQV
t
t
(PA)
(PA)
QXRH
RHQZ
RLRH
t
(PA)
DVQV
DATA ON PORT A
AI02897
Table 60. Port A Peripheral Data Mode READ Timing (5V devices)
-70
-90
-15
Turbo
Off
Symbol
Parameter
Conditions
Unit
Min Max Min Max Min Max
Address Valid to Data
Valid
3
t
t
37
39
45
+ 10
+ 10
ns
AVQV–PA
SLQV–PA
(Note )
CSI Valid to Data Valid
RD to Data Valid
27
21
32
22
35
32
38
30
45
40
45
38
ns
ns
ns
ns
ns
ns
1,4
(Notes
)
t
RLQV–PA
RD to Data Valid 8031 Mode
Data In to Data Out Valid
RD Data Hold Time
RD Pulse Width
t
t
t
DVQV–PA
QXRH–PA
RLRH–PA
0
0
0
1
27
32
38
(Note )
1
t
RD to Data High-Z
23
25
30
ns
RHQZ–PA
(Note )
90/103
PSD81XFX, PSD83XF2, PSD85XF2
Table 61. Port A Peripheral Data Mode READ Timing (3V devices)
-12
-15
-20
Turbo
Off
Symbol
Parameter
Conditions
Unit
Min Max Min Max Min Max
3
t
t
Address Valid to Data Valid
50
50
50
+ 20
+ 20
ns
AVQV–PA
SLQV–PA
(Note )
CSI Valid to Data Valid
RD to Data Valid
37
37
45
38
45
40
45
40
50
45
50
45
ns
ns
ns
ns
ns
ns
1,4
(Notes
)
t
RLQV–PA
RD to Data Valid 8031 Mode
Data In to Data Out Valid
RD Data Hold Time
RD Pulse Width
t
t
t
DVQV–PA
QXRH–PA
RLRH–PA
0
0
0
1
36
36
46
(Note )
1
t
RD to Data High-Z
36
40
45
ns
RHQZ–PA
(Note )
91/103
PSD81XFX, PSD83XF2, PSD85XF2
Figure 45. Peripheral I/O WRITE Timing
ALE/AS
ADDRESS
DATA OUT
A/D BUS
tWHQZ (PA)
tWLQV (PA)
WR
tDVQV (PA)
PORT A
DATA OUT
AI02898
Table 62. Port A Peripheral Data Mode WRITE Timing (5V devices)
-70
-90
-15
Symbol
Parameter
Conditions
Unit
Min Max Min Max Min Max
2
t
t
t
WR to Data Propagation Delay
Data to Port A Data Propagation Delay
WR Invalid to Port A Tri-state
25
22
20
35
30
25
40
38
33
ns
ns
ns
WLQV–PA
DVQV–PA
WHQZ–PA
(Note )
5
(Note )
2
(Note )
Note: 1. RD has the same timing as DS, LDS, UDS, and PSEN (in 8031 combined mode).
2. WR has the same timing as the E, LDS, UDS, WRL, and WRH signals.
3. Any input used to select Port A Data Peripheral mode.
4. Data is already stable on Port A.
5. Data stable on ADIO pins to data on Port A.
Table 63. Port A Peripheral Data Mode WRITE Timing (3V devices)
-12
-15
-20
Symbol
Parameter
Conditions
Unit
Min Max Min Max Min Max
2
t
t
t
WR to Data Propagation Delay
Data to Port A Data Propagation Delay
WR Invalid to Port A Tri-state
42
38
33
45
40
33
55
45
35
ns
ns
ns
WLQV–PA
DVQV–PA
WHQZ–PA
(Note )
5
(Note )
2
(Note )
Note: 1. RD has the same timing as DS, LDS, UDS, and PSEN (in 8031 combined mode).
2. WR has the same timing as the E, LDS, UDS, WRL, and WRH signals.
3. Any input used to select Port A Data Peripheral mode.
4. Data is already stable on Port A.
5. Data stable on ADIO pins to data on Port A.
92/103
PSD81XFX, PSD83XF2, PSD85XF2
Figure 46. Reset (RESET) Timing
VCC(min)
V
CC
t
NLNH
t
t
OPR
t
t
OPR
NLNH-PO
NLNH-A
Power-On Reset
Warm Reset
RESET
AI02866b
Table 64. Reset (RESET) Timing (5V devices)
Symbol
Parameter
Conditions
Min
150
1
Max
Unit
1
t
t
t
t
ns
ms
µs
ns
NLNH
RESET Active Low Time
Power On Reset Active Low Time
NLNH–PO
NLNH–A
OPR
2
25
Warm Reset (on the PSD834Fx)
RESET High to Operational Device
120
Note: 1. Reset (RESET) does not reset Flash memory Program or Erase cycles.
2. Warm reset aborts Flash memory Program or Erase cycles, and puts the device in READ Mode.
Table 65. Reset (RESET) Timing (3V devices)
Symbol
Parameter
Conditions
Min
300
1
Max
Unit
ns
1
t
t
t
t
NLNH
RESET Active Low Time
Power On Reset Active Low Time
ms
µs
NLNH–PO
NLNH–A
OPR
2
25
Warm Reset (on the PSD834Fx)
RESET High to Operational Device
300
ns
Note: 1. Reset (RESET) does not reset Flash memory Program or Erase cycles.
2. Warm reset aborts Flash memory Program or Erase cycles, and puts the device in READ Mode.
Table 66. V
Symbol
Timing (5V devices)
Parameter
STBYON
Conditions
Min
Typ
Max
Unit
1
t
V
STBY
Detection to V
Output High
STBYON
20
µs
BVBH
(Note )
V
Low
Off Detection to V
Output
STBYON
STBY
1
t
20
µs
BXBL
(Note )
Note: 1. V
timing is measured at V ramp rate of 2 ms.
CC
STBYON
Table 67. V
Symbol
Timing (3V devices)
Parameter
STBYON
Conditions
Min
Typ
Max
Unit
1
t
V
STBY
Detection to V
Output High
STBYON
20
µs
BVBH
(Note )
V
Low
Off Detection to V
Output
STBYON
STBY
1
t
20
µs
BXBL
(Note )
Note: 1. V
timing is measured at V ramp rate of 2 ms.
CC
STBYON
93/103
PSD81XFX, PSD83XF2, PSD85XF2
Figure 47. ISC Timing
tISCCH
TCK
tISCCL
tISCPSU
tISCPH
TDI/TMS
t ISCPZV
tISCPCO
ISC OUTPUTS/TDO
tISCPVZ
ISC OUTPUTS/TDO
AI02865
Table 68. ISC Timing (5V devices)
-70
-90
-15
Symbol
Parameter
Conditions
Unit
Min Max Min Max Min Max
Clock (TCK, PC1) Frequency (except for
PLD)
1
t
20
18
14 MHz
ISCCF
ISCCH
ISCCL
(Note )
Clock (TCK, PC1) High Time (except for
PLD)
1
t
t
23
23
26
26
31
31
ns
ns
(Note )
Clock (TCK, PC1) Low Time (except for
PLD)
1
(Note )
2
t
t
Clock (TCK, PC1) Frequency (PLD only)
Clock (TCK, PC1) High Time (PLD only)
2
2
2
MHz
ns
ISCCFP
ISCCHP
(Note )
2
240
240
240
(Note )
2
t
t
t
t
t
Clock (TCK, PC1) Low Time (PLD only)
ISC Port Set Up Time
240
7
240
8
240
10
5
ns
ns
ns
ns
ns
ISCCLP
ISCPSU
ISCPH
(Note )
ISC Port Hold Up Time
5
5
ISC Port Clock to Output
21
21
23
23
25
25
ISCPCO
ISCPZV
ISC Port High-Impedance to Valid Output
ISC Port Valid Output to
High-Impedance
t
21
23
25
ns
ISCPVZ
Note: 1. For non-PLD Programming, Erase or in ISC by-pass mode.
2. For Program or Erase PLD only.
94/103
PSD81XFX, PSD83XF2, PSD85XF2
Table 69. ISC Timing (3V devices)
-12
-15
-20
Symbol
Parameter
Conditions
Unit
Min Max Min Max Min Max
Clock (TCK, PC1) Frequency (except for
PLD)
1
t
12
10
9
2
MHz
ns
ISCCF
ISCCH
ISCCL
(Note )
Clock (TCK, PC1) High Time (except for
PLD)
1
t
t
40
40
45
45
51
51
(Note )
Clock (TCK, PC1) Low Time (except for
PLD)
1
ns
(Note )
2
t
t
Clock (TCK, PC1) Frequency (PLD only)
Clock (TCK, PC1) High Time (PLD only)
2
2
MHz
ns
ISCCFP
ISCCHP
(Note )
2
240
240
240
(Note )
2
t
t
t
t
t
Clock (TCK, PC1) Low Time (PLD only)
ISC Port Set Up Time
240
12
5
240
13
5
240
15
5
ns
ns
ns
ns
ns
ISCCLP
ISCPSU
ISCPH
(Note )
ISC Port Hold Up Time
ISC Port Clock to Output
30
30
36
36
40
40
ISCPCO
ISCPZV
ISC Port High-Impedance to Valid Output
ISC Port Valid Output to
High-Impedance
t
30
36
40
ns
ISCPVZ
Note: 1. For non-PLD Programming, Erase or in ISC by-pass mode.
2. For Program or Erase PLD only.
Table 70. Power-down Timing (5V devices)
-70
-90
-15
Symbol
Parameter
Conditions
Unit
Min Max Min Max Min Max
t
ALE Access Time from Power-down
80
90
150
ns
LVDV
Maximum Delay from
APD Enable to Internal PDN Valid
Signal
Using CLKIN
(PD1)
1
t
µs
15 * t
CLWH
CLCL
Note: 1. t
is the period of CLKIN (PD1).
CLCL
Table 71. Power-down Timing (3V devices)
-12
Min Max Min Max Min Max
145 150 200
-15
-20
Symbol
Parameter
Conditions
Unit
t
ALE Access Time from Power-down
ns
µs
LVDV
Maximum Delay from APD Enable to
Internal PDN Valid Signal
Using CLKIN
(PD1)
1
t
15 * t
CLWH
CLCL
Note: 1. t
is the period of CLKIN (PD1).
CLCL
95/103
PSD81XFX, PSD83XF2, PSD85XF2
PACKAGE MECHANICAL
Figure 48. PQFP52 Connections
Figure 49. PLCC52 Connections
8
PD2
PD1
PD0
PC7
PC6
PC5
PC4
AD15
AD14
AD13
AD12
AD11
AD10
AD9
46
45
44
43
42
41
40
39
38
37
36
9
PD2
PD1
PD0
PC7
PC6
PC5
PC4
1
2
3
4
5
6
7
8
39 AD15
38 AD14
37 AD13
36 AD12
35 AD11
34 AD10
33 AD9
10
11
12
13
14
15
16
17
18
V
32 AD8
CC
V
AD8
CC
GND 9
31 V
CC
PC3 10
PC2 11
PC1 12
PC0 13
30 AD7
29 AD6
28 AD5
27 AD4
GND
V
CC
PC3
PC2
AD7
AD6
19
20
PC1
PC0
AD5
AD4
35
34
AI02858
AI02857
Figure 50. PQFP52 - 52-pin Plastic, Quad, Flat Package Mechanical Drawing
D
D1
D2
A2
e
b
Ne
E2 E1
E
N
1
Nd
A
CP
L1
c
A1
α
L
QFP-A
Note: Drawing is not to scale.
96/103
PSD81XFX, PSD83XF2, PSD85XF2
Table 72. PQFP52 - 52-pin Plastic, Quad, Flat Package Mechanical Dimensions
mm
inches
Symb.
Typ.
Min.
Max.
2.35
0.25
2.10
0.38
0.23
13.25
10.05
–
Typ.
Min.
Max.
0.093
0.010
0.083
0.015
0.009
0.522
0.396
–
A
A1
A2
b
2.00
1.80
0.22
0.11
13.15
9.95
–
0.079
0.077
0.009
0.004
0.518
0.392
–
c
D
13.20
10.00
7.80
0.520
0.394
0.307
0.520
0.394
0.307
0.026
0.035
0.063
D1
D2
E
13.20
10.00
7.80
13.15
9.95
–
13.25
10.05
–
0.518
0.392
–
0.522
0.396
–
E1
E2
e
0.65
–
–
L
0.88
0.73
–
1.03
–
0.029
0.041
7°
L1
α
1.60
0°
7°
0°
52
13
13
N
52
Nd
Ne
CP
13
13
0.10
0.004
97/103
PSD81XFX, PSD83XF2, PSD85XF2
Figure 51. PLCC52 - 52-lead Plastic Lead, Chip Carrier Package Mechanical Drawing
D
A1
D1
A2
M1
M
1 N
b1
e
E1 E
D2/E2 D3/E3
b
L1
L
C
A
CP
PLCC-B
Note: Drawing is not to scale.
Table 73. PLCC52 - 52-lead Plastic Lead, Chip Carrier Package Mechanical Dimensions
mm
Min.
4.19
2.54
–
inches
Min.
0.165
0.100
–
Symbol
Typ.
Max.
4.57
2.79
0.91
0.53
0.81
0.261
20.19
19.15
18.54
20.19
19.15
18.54
–
Typ.
Max.
0.180
0.110
0.036
0.021
0.032
A
A1
A2
B
0.33
0.66
0.246
19.94
19.05
17.53
19.94
19.05
17.53
–
0.013
0.026
0.0097
0.785
0.750
0.690
0.785
0.750
0.690
–
B1
C
0.0103
0.795
0.754
0.730
0.795
0.754
0.730
–
D
D1
D2
E
E1
E2
e
1.27
0.89
0.050
0.035
R
–
–
–
–
N
52
52
Nd
Ne
13
13
13
13
98/103
PSD81XFX, PSD83XF2, PSD85XF2
PART NUMBERING
Table 74. Ordering Information Scheme
Example:
PSD8
1
3
F
2
V
–
15
J
1
T
Device Type
PSD8 = 8-bit PSD with Register Logic
PSD9 = 8-bit PSD with Combinatorial Logic
SRAM Capacity
1 = 16 Kbit
3 = 64 Kbit
5 = 256 Kbit
Flash Memory Capacity
3 = 1 Mbit (128K x 8)
4 = 2 Mbit (256K x 8)
2nd Flash Memory
2 = 256 Kbit Flash memory + SRAM
3 = SRAM but no Flash memory
4 = 256 Kbit Flash memory but no SRAM
5 = no Flash memory + no SRAM
Operating Voltage
blank = V = 4.5 to 5.5V
CC
V = V = 3.0 to 3.6V
CC
Speed
70 = 70ns
90 = 90ns
12 = 120ns
15 = 150ns
20 = 200ns
Package
J = PLCC52
M = PQFP52
Temperature Range
blank = 0 to 70°C (commercial)
I = –40 to 85°C (industrial)
Option
T = Tape & Reel Packing
For a list of available options (e.g., speed, package) or for further information on any aspect of this device,
please contact your nearest ST Sales Office.
99/103
PSD81XFX, PSD83XF2, PSD85XF2
APPENDIX A. PQFP52 PIN ASSIGNMENTS
Table 75. PQFP52 Connections (Figure 48)
Pin Number
Pin Assignments
Pin Number
Pin Assignments
1
PD2
PD1
PD0
PC7
PC6
PC5
PC4
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
AD4
AD5
AD6
AD7
2
3
4
5
V
CC
6
AD8
AD9
7
V
CC
8
AD10
AD11
AD12
AD13
AD14
AD15
CNTL0
RESET
CNTL2
CNTL1
PB7
9
GND
PC3
PC2
PC1
PC0
PA7
PA6
PA5
PA4
PA3
GND
PA2
PA1
PA0
AD0
AD1
AD2
AD3
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
PB6
GND
PB5
PB4
PB3
PB2
PB1
PB0
100/103
PSD81XFX, PSD83XF2, PSD85XF2
APPENDIX B. PLCC52 PIN ASSIGNMENTS
Table 76. PLCC52 Connections (Figure 49)
Pin Number
Pin Assignments
Pin Number
Pin Assignments
1
GND
PB5
PB4
PB3
PB2
PB1
PB0
PD2
PD1
PD0
PC7
PC6
PC5
PC4
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
PA2
PA1
PA0
AD0
AD1
AD2
AD3
AD4
AD5
AD6
AD7
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
V
CC
AD8
AD9
V
CC
AD10
AD11
AD12
AD13
AD14
AD15
CNTL0
RESET
CNTL2
CNTL1
PB7
GND
PC3
PC2 (V
)
STBY
PC1
PC0
PA7
PA6
PA5
PA4
PA3
GND
PB6
101/103
PSD81XFX, PSD83XF2, PSD85XF2
REVISION HISTORY
Table 77. Document Revision History
Date
Rev.
Description of Revision
15-Oct-99
27-Oct-00
30-Nov-00
23-Oct-01
07-Apr-03
12-Jun-03
02-Oct-03
1.0 Initial release as a WSI document
1.1 Port A Peripheral Data Mode Read Timing, changed to 50
1.2 PSD85xF2 added
2.0 Document rewritten using the ST template
3.0 v2.2 Template applied; voltage correction (Table 74)
3.1 Fix errors in PQFQ52 Connections (Table 75)
3.2 Correct Instructions (Table 8); update disclaimer, Title for EDOCS application
102/103
PSD81XFX, PSD83XF2, PSD85XF2
Information furnished is believed to be accurate and reliable. However, STMicroelectronics assumes no responsibility for the consequences
of use of such information nor for any infringement of patents or other rights of third parties which may result from its use. No license is granted
by implication or otherwise under any patent or patent rights of STMicroelectronics. Specifications mentioned in this publication are subject
to change without notice. This publication supersedes and replaces all information previously supplied. STMicroelectronics products are not
authorized for use as critical components in life support devices or systems without express written approval of STMicroelectronics.
The ST logo is a registered trademark of STMicroelectronics.
All other names are the property of their respective owners
© 2003 STMicroelectronics - All rights reserved
STMicroelectronics GROUP OF COMPANIES
Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan -
Malaysia - Malta - Morocco - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States
www.st.com
103/103
相关型号：
©2020 ICPDF网 联系我们和版权申明