PI74FCT162H374CTV [ETC]
16-Bit D-Type Flip-Flop ; 16位D型触发器\n![PI74FCT162H374CTV](http://pdffile.icpdf.com/pdf1/p00013/img/icpdf/PI74F_62163_icpdf.jpg)
型号: | PI74FCT162H374CTV |
厂家: | ![]() |
描述: | 16-Bit D-Type Flip-Flop
|
文件: | 总7页 (文件大小:229K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
![](http://public.icpdf.com/style/img/ads.jpg)
PI74FCT16374T
PI74FCT162374T
PI74FCT162H374T
Fast CMOS 16-Bit
Registers (3-State)
ProductFeatures:
CommonFeatures:
Product Description:
PI74FCT16374T,PI74FCT162374T,andPI74FCT162H374T
are high-speed,
low power devices with high current drive.
Vcc=5V±10%
Pericom Semiconductors PI74FCT series of logic circuits are
producedintheCompanysadvanced0.6micronCMOStechnology,
achieving industry leading speed grades.
ThePI74FCT16374T,PI74FCT162374T,andPI74FCT162H374T
are 16-bit octal registers designed with 16 D-type flip-flops with a
buffered common clock and 3-state outputs. The Output Enable
(xOE) and clock (xCLK) controls are organized to operate as
two 8-bit registers or one 16-bit register. When OE is HIGH, the
outputs are in the high impedance state. Input data meeting the
setup and hold time requirements of the D inputs is transferred to
the O outputs on the LOW-to-HIGH transition of the clock input.
Hysteresis on all inputs
Packagesavailable:
48-pin240milwideplasticTSSOP(A)
48-pin300milwideplasticSSOP(V)
PI74FCT16374TFeatures:
High output drive: IOH = 32 mA; IOL = 64 mA
Power off disable outputs permit "live insertion"
Typical VOLP (Output Ground Bounce) < 1.0V
atVCC =5V,TA =25°C
PI74FCT162374TFeatures:
Balanced output drivers: ±24 mA
Reduced system switching noise
Typical VOLP (Output Ground Bounce) < 0.6V
atVCC =5V,TA =25°C
PI74FCT162H374TFeatures:
The PI74FCT16374T output buffers are designed with a Power-Off
disable allowing live insertion of boards when used as backplane
drivers.
The PI74FCT162374T has ±24 mA balanced output drivers. It is
designed with current limiting resistors at its outputs to control the
output edge rate resulting in lower ground bounce and undershoot.
This eliminates the need for external terminating resistors for most
interface applications.
Bus Hold retains last active bus state during 3-state
Eliminates the need for external pull-up resistors
The PI74FCT162H374T has Bus Hold which retains the inputs
last state whenever the input goes to high-impedance preventing
floating inputs and eliminating the need for pull-up/down
resistors.
Logic Block Diagram
1OE
2OE
1CLK
2CLK
1D0
2D0
D
D
1O0
2O0
C
C
TO 7 OTHER CHANNELS
TO 7 OTHER CHANNELS
PS2034A 03/11/96
1
PI74FCT16374/162374/162H374T
16-BIT REGISTERS (3-STATE)
Truth Table(1)
Product Pin Description
Inputs
Outputs
Pin Name
xOE
Description
Function
XDX
X
XCLK
XOE
H
XOX
Z
3-State Output Enable Inputs (Active LOW)
High-Z
L
H
↑
xCLK
xDx
Clock Inputs
Inputs(1)
X
H
Z
Load Register
L
L
L
xOx
3-State Outputs
Ground
H
↑
L
H
Z
GND
VCC
L
↑
H
Power
H
↑
H
Z
Note: 1. For the PI74FCT162H374T, these pins have Bus
Hold. All other pins are standard, outputs, or I/Os.
Note:
1. H = High Voltage Level
L = Low Voltage Level
X = Dont Care
Z = High Impedance
↑ = LOW-to-HIGH transition
Product Pin Configuration
1
OE
1
1
1
CLK
1
48
47
46
45
44
43
42
41
40
39
38
37
36
35
34
33
32
31
30
29
28
27
26
25
1
O
O
0
1
D
0
1
2
1
D
3
GND
GND
4
1
1
O
O
2
3
1
1
D
2
3
5
D
6
V
CC
VCC
7
1
O
O
4
5
1
D4
8
1
1
D5
9
GND
GND
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
48-PIN
V48
A48
1
1
2
2
O
O
O
O
6
7
0
1
1
1
2
2
D6
D7
D0
D1
GND
GND
2
2
O
O
2
3
2
2
D
2
3
D
V
CC
VCC
2
O
O
4
5
2
D4
2
2
D5
GND
GND
2
2
O
O
6
7
2
2
2
D
6
7
D
2
OE
CLK
PS2034A 03/11/96
2
PI74FCT16374/162374/162H374T
16-BIT REGISTERS (3-STATE)
MaximumRatings
(Above which the useful life may be impaired. For user guidelines, not tested.)
Note:
Storage Temperature .................................................................... 65°Cto+150°C
Ambient Temperature with Power Applied ....................................40°Cto+85°C
Supply Voltage to Ground Potential (Inputs & Vcc Only) .............. 0.5Vto+7.0V
Supply Voltage to Ground Potential (Outputs & D/O Only) ........... 0.5Vto+7.0V
DC Input Voltage ............................................................................0.5Vto+7.0V
DC Output Current ..................................................................................... 120mA
Power Dissipation ..........................................................................................1.0W
Stresses greater than those listed under
MAXIMUM RATINGS may cause permanent
damage to the device. This is a stress rating
only and functional operation of the device at
these or any other conditions above those
indicated in the operational sections of this
specification is not implied. Exposure to
absolute maximum rating conditions for
extended periods may affect reliability.
DC Electrical Characteristics (Over the Operating Range, TA = 40°C to +85°C, VCC = 5.0V ± 10%)
Parameters Description
TestConditions(1)
Min.
Typ(2) Max.
Units
VIH
VIL
IIH
IIH
IIH
IIH
IIL
IIL
IIL
InputHIGHVoltage
GuaranteedLogicHIGHLevel
GuaranteedLogicLOWLevel
Standard Input, VCC = Max.
StandardI/O, VCC = Max.
Bus Hold Input(4), VCC = Max.
BusHoldI/O(4), VCC = Max.
Standard Input, VCC = Min.
Standard I/O, VCC = Min.
2.0
V
V
Input LOW Voltage
InputHIGHCurrent
InputHIGHCurrent
InputHIGHCurrent
InputHIGHCurrent
Input LOW Current
Input LOW Current
Input LOW Current
Input LOW Current
Bus Hold
Sustain Current
HighImpedance
Output Current
ClampDiodeVoltage
ShortCircuitCurrent
Output Drive Current
Input Hysteresis
0.8
1
1
±100
±100
1
1
±100
±100
VIN =VCC
VIN =VCC
VIN =VCC
VIN =VCC
VIN=GND
VIN=GND
VIN= GND
VIN= GND
VIN=2.0V
VIN=0.8V
VOUT =2.7V
VOUT =0.5V
µA
µA
µA
µA
µA
µA
µA
µA
µA
Bus Hold Input(4), VCC = Min.
Bus Hold I/O(4), VCC = Min.
Bus Hold Input(4), VCC = Min.
IIL
IBHH
IBHL
IOZH
IOZL
VIK
IOS
IO
50
+50
(5)
(5)
VCC =Max.
VCC =Max.
VCC =Min., IIN =18mA
VCC =Max.(3),VOUT = GND
VCC =Max.(3),VOUT =2.5V
1
1
1.2
200
180
µA
µA
V
mA
mA
mV
0.7
140
80
50
VH
100
Notes:
1. For Max. or Min. conditions, use appropriate value specified under Electrical Characteristics for the applicable device type.
2. Typical values are at Vcc = 5.0V, +25°C ambient and maximum loading.
3. Not more than one output should be shorted at one time. Duration of the test should not exceed one second.
4. Pins with Bus Hold are identified in the pin description.
5. This specification does not apply to bi-directional functionalities with Bus Hold.
PS2034A 03/11/96
3
PI74FCT16374/162374/162H374T
16-BIT REGISTERS (3-STATE)
PI74FCT16374T Output Drive Characteristics (Over the Operating Range)
Parameters Description
TestConditions(1)
Min.
Typ(2) Max.
Units
VOH
OutputHIGHVoltage
VCC =Min.,VIN =VIH orVIL
IOH = 3.0 mA
IOH =15.0mA
IOH = 32.0 mA
IOL = 64 mA
2.5
2.4
2.0
3.5
3.5
3.0
0.2
V
VOL
IOFF
Output LOW Voltage VCC = Min., VIN = VIH or VIL
PowerDownDisable VCC =0V,VIN orVOUT ≤4.5V
0.55
±100
V
µA
PI74FCT162374T/162H374TOutputDriveCharacteristics(OvertheOperatingRange)
Parameters Description
TestConditions(1)
Min.
Typ(2) Max.
Units
VOH
VOL
IODL
IODH
OutputHIGHVoltage
VCC =Min.,VIN =VIH orVIL
VCC =Min.,VIN =VIH orVIL
IOH =24.0mA
IOL = 24 mA
2.4
3.3
0.3
115
V
V
mA
mA
Output LOW Voltage
Output LOW Current
OutputHIGHCurrent
0.55
150
150
VCC =5V,VIN =VIH OR VIL,VOUT =1.5V(3)
VCC =5V,VIN =VIH OR VIL,VOUT =1.5V(3)
60
60
115
Capacitance (TA = 25°C, f = 1 MHz)
Parameters(4)
Description
Test Conditions
Typ
Max.
Units
CIN
Input Capacitance
Output Capacitance
VIN = 0V
4.5
5.5
6
8
pF
pF
COUT
VOUT = 0V
Notes:
1. For Max. or Min. conditions, use appropriate value specified under Electrical Characteristics for the applicable device type.
2. Typical values are at Vcc = 5.0V, +25°C ambient and maximum loading.
3. Not more than one output should be shorted at one time. Duration of the test should not exceed one second.
4. This parameter is determined by device characterization but is not production tested.
PS2034A 03/11/96
4
PI74FCT16374/162374/162H374T
16-BIT REGISTERS (3-STATE)
Power Supply Characteristics
Parameters Description
Test Conditions(1)
Min. Typ(2) Max. Units
ICC
Quiescent Power
Supply Current
VCC = Max.
VIN = GND or VCC
0.1
0.5
60
500
µA
∆ICC
ICCD
Supply Current per
Input @ TTL HIGH
VCC = Max.
VIN = 3.4V(3)
1.5
mA
Supply Current per
Input per MHz(4)
VCC = Max.,
Outputs Open
XOE = GND
VIN = VCC
VIN = GND
100
µA/
MHz
One Bit Toggling
50% Duty Cycle
IC
Total Power Supply
Current(6)
VCC = Max.,
VIN = VCC
VIN = GND
0.6
1.1
1.5(5)
3.0(5)
mA
Outputs Open
fCP = 10 MHZ
50% Duty Cycle
XOE = GND
VIN = 3.4V
VIN = GND
fI = 5 MHZ
50% Duty Cycle
One Bit Toggling
VCC = Max.,
VIN = VCC
VIN = GND
3.0
7.5
5.5(5)
Outputs Open
fCP = 10 MHZ
50% Duty Cycle
XOE = GND
VIN = 3.4V
VIN = GND
19.0(5)
16 Bits Toggling
fI = 2.5 MHZ
50% Duty Cycle
Notes:
1. For Max. or Min. conditions, use appropriate value specified under Electrical Characteristics for the applicable device.
2. Typical values are at Vcc = 5.0V, +25°C ambient.
3. Per TTL driven input (VIN = 3.4V); all other inputs at Vcc or GND.
4. This parameter is not directly testable, but is derived for use in Total Power Supply Calculations.
5. Values for these conditions are examples of the Icc formula. These limits are guaranteed but not tested.
6. IC =IQUIESCENT + IINPUTS + IDYNAMIC
IC = ICC + ∆ICC DHNT + ICCD (fCP/2 + fINI)
ICC = Quiescent Current
∆ICC = Power Supply Current for a TTL High Input (VIN = 3.4V)
DH = Duty Cycle for TTL Inputs High
NT = Number of TTL Inputs at DH
ICCD = Dynamic Current Caused by an Input Transition Pair (HLH or LHL)
fCP = Clock Frequency for Register Devices (Zero for Non-Register Devices)
fI = Input Frequency
NI = Number of Inputs at fI
All currents are in milliamps and all frequencies are in megahertz.
PS2034A 03/11/96
5
PI74FCT16374/162374/162H374T
16-BIT REGISTERS (3-STATE)
PI74FCT16374T Switching Characteristics over Operating Range
16374T
Com.
16374AT
Com.
16374CT
Com.
16374DT
Com.
16374ET
Com.
Parameters
Description
Conditions(1)
Min Max Min Max Min Max Min Max Min Max Unit
t
t
PLH
PHL
PropagationDelay
xCLKxtoxOx
Output Enable Time
xOE to xOx
OutputDisableTime(3)
xOEtoxOx
Setup Time HIGH
C
R
L
L
= 50 pF
=500Ω
2.0
10.0
2.0
6.5
6.5
5.5
2.0
1.5
1.5
2.0
1.5
5.0
5.2
5.5
5.0
2.0
1.5
1.5
2.0
1.0
3.0
4.2
4.8
4.0
1.5
1.5
1.5
1.5
0.0
3.0
3.7
4.4
4.0
ns
ns
ns
ns
ns
ns
ns
tPZH
1.5 12.5 1.5
tPZL
t
t
PHZ
PLZ
1.5
2.0
1.5
7.0
8.0
0.5
1.5
2.0
1.5
5.0
tSU
or LOW,
Hold Time HIGH
or LOW, to
X
DX
to
X
CLK
tH
X
DX
X
CLK
tW
xCLK Pulse Width
HIGH or LOW(3)
Output Skew(4)
t
SK(o)
0.5
0.5
0.5
0.5
PI74FCT162374T Switching Characteristics over Operating Range
162374T
Com.
162374AT 162374CT 162374DT 162374ET
Com. Com. Com. Com.
Parameters
Description
Conditions(1)
Min Max Min Max Min Max Min Max Min Max Unit
t
t
PLH
PHL
PropagationDelay
xCLKxtoxOx
Output Enable Time
xOE to xOx
OutputDisableTime(3)
xOEtoxOx
Setup Time HIGH
C
R
L
L
= 50 pF
=500Ω
2.0
10.0
2.0
6.5
6.5
5.5
0.5
2.0
1.5
1.5
2.0
1.5
5.0
5.2
5.5
5.0
0.5
2.0
1.5
1.5
2.0
1.0
3.0
4.2
4.8
4.0
0.5
1.5
1.5
1.5
1.5
0.0
3.0
3.7
4.4
4.0
0.5
ns
ns
ns
ns
ns
ns
ns
tPZH
1.5 12.5 1.5
tPZL
t
t
PHZ
PLZ
1.5
2.0
1.5
7.0
8.0
0.5
1.5
2.0
1.5
5.0
tSU
or LOW,
Hold Time HIGH
or LOW, to
X
DX
to
X
CLK
tH
X
DX
X
CLK
tW
xCLK Pulse Width
HIGH or LOW(3)
OutputSkew(4)
tSK(o)
Notes:
1. See test circuit and wave forms.
2. Minimum limits are guaranteed but not tested on Propagation Delays.
3. This parameter is guaranteed but not production tested.
4. Skew between any two outputs, of the same package, switching in the same direction. This parameter is guaranteed by design.
PS2034A 03/11/96
6
PI74FCT16374/162374/162H374T
16-BIT REGISTERS (3-STATE)
PI74FCT162H374T Switching Characteristics over Operating Range
162H374T 162H374AT 162H374CT 162H374DT 162H374ET
Com. Com. Com. Com. Com.
Min Max Min Max Min Max Min Max Min Max Unit
Parameters
Description
Conditions(1)
t
t
t
t
t
t
t
PLH
PHL
PZH
PZL
PHZ
PLZ
SU
PropagationDelay
xCLKxtoxOx
Output Enable Time
xOE to xOx
Output Disable Time(3)
xOE to xOx
Setup Time HIGH
C
R
L
L
= 50 pF
=500Ω
2.0
10.0
2.0
6.5
6.5
5.5
2.0
1.5
1.5
2.0
1.5
5.0
5.2
5.5
5.0
2.0
1.5
1.5
2.0
1.0
3.0
4.2
4.8
4.0
1.5
1.5
1.5
1.5
0.0
3.0
3.7
4.4
4.0
ns
ns
ns
ns
ns
ns
ns
1.5 12.5 1.5
1.5
2.0
1.5
7.0
8.0
0.5
1.5
2.0
1.5
5.0
or LOW,
Hold Time HIGH
or LOW, to
X
D
X
to
X
CLK
t
t
H
X
D
X
XCLK
W
xCLK Pulse Width
HIGH or LOW(3)
OutputSkew(4)
tSK(o)
0.5
0.5
0.5
0.5
Notes:
1. See test circuit and wave forms.
2. Minimum limits are guaranteed but not tested on Propagation Delays.
3. This parameter is guaranteed but not production tested.
4. Skew between any two outputs, of the same package, switching in the same direction. This parameter is guaranteed by design.
Pericom Semiconductor Corporation
2380 Bering Drive • San Jose, CA 95131 • 1-800-435-2336 • Fax (408) 435-1100 • http://www.pericom.com
PS2034A 03/11/96
7
相关型号:
![](http://pdffile.icpdf.com/pdf2/p00245/img/page/PI74FCT16237_1489144_files/PI74FCT16237_1489144_1.jpg)
![](http://pdffile.icpdf.com/pdf2/p00245/img/page/PI74FCT16237_1489144_files/PI74FCT16237_1489144_2.jpg)
PI74FCT162H374CTVX
Bus Driver, FCT Series, 2-Func, 8-Bit, True Output, CMOS, PDSO48, 0.300 INCH, PLASTIC, SSOP-48
PERICOM
![](http://pdffile.icpdf.com/pdf1/p00030/img/page/PI74FCT162H374T_157471_files/PI74FCT162H374T_157471_1.jpg)
![](http://pdffile.icpdf.com/pdf1/p00030/img/page/PI74FCT162H374T_157471_files/PI74FCT162H374T_157471_2.jpg)
PI74FCT162H374DTAX
Bus Driver, FCT Series, 2-Func, 8-Bit, True Output, CMOS, PDSO48, 0.240 INCH, PLASTIC, TSSOP-48
PERICOM
![](http://pdffile.icpdf.com/pdf2/p00245/img/page/PI74FCT16237_1489144_files/PI74FCT16237_1489144_1.jpg)
![](http://pdffile.icpdf.com/pdf2/p00245/img/page/PI74FCT16237_1489144_files/PI74FCT16237_1489144_2.jpg)
PI74FCT162H374ETAX
Bus Driver, FCT Series, 2-Func, 8-Bit, True Output, CMOS, PDSO48, 0.240 INCH, PLASTIC, TSSOP-48
PERICOM
![](http://pdffile.icpdf.com/pdf2/p00245/img/page/PI74FCT16237_1489144_files/PI74FCT16237_1489144_1.jpg)
![](http://pdffile.icpdf.com/pdf2/p00245/img/page/PI74FCT16237_1489144_files/PI74FCT16237_1489144_2.jpg)
PI74FCT162H374ETVX
Bus Driver, FCT Series, 2-Func, 8-Bit, True Output, CMOS, PDSO48, 0.300 INCH, PLASTIC, SSOP-48
PERICOM
![](http://pdffile.icpdf.com/pdf2/p00285/img/page/PI74FCT16237_1700701_files/PI74FCT16237_1700701_1.jpg)
![](http://pdffile.icpdf.com/pdf2/p00285/img/page/PI74FCT16237_1700701_files/PI74FCT16237_1700701_2.jpg)
PI74FCT162H374TA
Bus Driver, FCT Series, 2-Func, 8-Bit, True Output, CMOS, PDSO48, 0.240 INCH, PLASTIC, TSSOP-48
PERICOM
![](http://pdffile.icpdf.com/pdf1/p00030/img/page/PI74FCT162H374T_157471_files/PI74FCT162H374T_157471_1.jpg)
![](http://pdffile.icpdf.com/pdf1/p00030/img/page/PI74FCT162H374T_157471_files/PI74FCT162H374T_157471_2.jpg)
PI74FCT162H374TAX
Bus Driver, FCT Series, 2-Func, 8-Bit, True Output, CMOS, PDSO48, 0.240 INCH, PLASTIC, TSSOP-48
PERICOM
![](http://pdffile.icpdf.com/pdf2/p00285/img/page/PI74FCT16237_1700701_files/PI74FCT16237_1700701_1.jpg)
![](http://pdffile.icpdf.com/pdf2/p00285/img/page/PI74FCT16237_1700701_files/PI74FCT16237_1700701_2.jpg)
PI74FCT162H374TV
Bus Driver, FCT Series, 2-Func, 8-Bit, True Output, CMOS, PDSO48, 0.300 INCH, PLASTIC, SSOP-48
PERICOM
©2020 ICPDF网 联系我们和版权申明