LEA-6S [ETC]
compact solution for adding GPS functionality to your device; 添加GPS功能，您的设备紧凑的解决方案
| 型号： | LEA-6S |
| 厂家： | 
ETC |
| 描述： | compact solution for adding GPS functionality to your device |
| 文件： | 总2页 (文件大小：475K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
2. Soldering the headers
Before using your click board, make sure
to solder the provided 1x8 male headers
to both sides of the board. Two 1x8 male
headers are included with the board in
the package.
1
GPS click
2
3
1. Introduction
4. Features and applications
GPS Click board with it’s LEA-6S module
features acquisition down to 1s, –147dBm
coldstart sensitivity and 5Hz update rate.
You can achive low power consumption
due to intelligent, user configurable power
management. Mentioned features make
this board ideal for asset tracking, road
navigation devices, public transportation
vehicle information systems and more.
Turn the board upside down, so that
bottom side is facing you upwards. Place
shorter parts of the header pins in the
both soldering pad locations.
Turn the board upward again. Make sure
to align the headers so that they are
perpendicular to the board, then solder the
pins carefully.
GPS Click is an accessory board in mikroBus™
3. Plugging the board in
form factor. It’s
a compact solution for
click
adding GPS functionality to your device. It
features LEA-6S, high performance u-blox 6
positioning engine. Board can be interfaced
with a microcontroller through UART or I2C
connection, or data can be acquired using PC
application through USB connection. Board
features connector compatible with active
and passive antennas. It can operate on
3.3V power supply only.
Once you have soldered the headers your
board is ready to be placed into desired
mikroBUS™ socket. Make sure to align the
cut in the lower-right part of the board
with the markings on the silkscreen at the
mikroBUS™ socket. If all the pins are aligned
correctly, push the board all the way
into the socket.
BOARD
www.mikroe.com
GPS click Manual
ver. 1.00
6. Power supply - 3.3V only
5. GPS click Board Schematics
Board is designed to use
3.3V power supply only. If
you need to add GPS feature
to your 5V prototype or
development board, we recommend you
to use other boards such as the SmartGPS
Accessory Board:
VCC
GPS1
R3 220
SDA2
SCL2
TxD1
RxD1
1
2
3
4
5
6
7
8
28
27
26
25
24
23
22
21
TIMEPULSE
SDA2
TIMEPULSE
EXTINT0
USB_DP
USB_DM
VDDUSB
NC
SCL2
TXD1
RXD1
NC
VCC
GND
USB_DP
USB_DM
VDD_USB
TIME PULSE
LED
http://www.mikroe.com/eng/products/
view/122/smartgps-board/
C2
VCC
CN4
ANTENNA
NC
NC
100nF
AN
RST
CS
PWM
INT
TX
VCC_OUT
RESET_N
TIMEPULSE
TxD1
RxD1
SCL2
SDA2
VCC_RF
9
20
19
18
17
16
15
7. Code Examples
SCK
RX
CFG_COM1
RESET
V_BCKP
Reserved
GND
AADENT0_N
V_ANT
VCC_RF
GND
R7 10
RF_IN
RESET_N
10
11
12
13
14
SCL
SDA
+5V
GND
MISO
MOSI
+3.3V
GND
Once you have done all the necessary
preparations, it’s time to get your click
board up and running. We have provided
the examples for mikroC, mikroBasic and
mikroPascal compilers on our Libstock
website. Just download them and you are
ready to start.
RF_IN
GND
GND
LEA6S
com
CN3
VDD_USB
VCC
D1
REG1
1
2
3
4
5
1
2
3
5
4
VBUS
D-
IN OUT
GND
USB_DM
USB_DP
8. Support
DEVICE/OTG
CONNECTOR
R5
220
BAT43
D+
C3
C1
R6
R1
1K
ID
GND
EN ADJ
AP7331-ADJ
2.2uF
180K
R2
2.2UF
POWER LED
MikroElektronika offers Free Tech Support
(www.mikroe.com/esupport) until the
end of product lifetime, so if something goes
wrong, we are ready and willing to help!
USB MINIB
300K
MikroElektronika assumes no responsibility or liability for any errors or inaccuracies that may appear in the present document.
Specification and information contained in the present schematic are subject to change at any time without notice. Copyright © 2012 MikroElektronika. All rights reserved.
相关型号：
©2020 ICPDF网 联系我们和版权申明