ATPG-L53C [ETC]
ATPG-L53C;Specification No.
Date
2002. 11.20
SPECIFICATIONS
5Φ Pure Green LED LAMP
MODEL : ATPG- L53C
Designed by
Checked by
Approved by
ACROSENTEC
MODEL : ATPG-L53C
2. Application
1. Features
1-1. InGaN Pure Green Chip
1-2. 5mm all epoxy resin mold type
1-3. Colorless Cylinder type LED lamp
1-4. Ultra luminous intensity
2-1. LED Display / Traffic Guiding signal
2-2. Illumination device
2-3. Back Light for Signboard
3. Dimension
▶Description :
•. 5mm, 30o Water clear type
• Designed for Ultra high brightness
Data subject to change.
MODEL : ATPG-L53C
4. Absolute maximum ratings and Characteristics
4 - 1 Absolute maximum ratings
Ta=25℃
Symbols
Ratings
Units
Items
IF
mA
mA
mW
Vr
Forward Current
30
Pulse Forward Current *1
Power Dissipation
IFP
100
PD
VR
78
5
Reverse Voltage
℃
Operating Temperature
Storage Temperature
Soldering Temperature *2
Topr
-30 ~ +85
-30 ~ +100
Tstg
TSOL
℃
℃
260±5℃
*1) Pulse Width = 100 μsec, Duty ≤ 10%
*2 ) 5sec at location 3.0mm away from the base of the epoxy bulb
4 - 2 Optical and Electrical Characteristics
Ta=25℃
Item
Symbol
Condition
Min
-
Typ
Max
Unit
Forward Voltage
Reverse Current
Luminous Intensity
Dominant Wavelength
Spectral Linewidth
Viewing Angle
VF
IR
IF=20[mA]
VR=5[V]
3.4
-
3.8
10
-
V
㎂
-
mcd
IV
IF=20[mA]
IF=20[mA]
4800
6000
525
λd
nm
IF=20[mA]
IF=20[mA]
-
Δλ
26
30
-
deg
2Θ1/2
Data subject to change.
MODEL : ATPG-L53C
6. Typical Electro-optical characteristics curve
■ Lead Temperature vs. Relative Luminosity
■Forward Voltage vs. Forward Current
100
10
1
1
0.1
-20
0
20
40
60
80
100
1.0
2.0
3.0
4.0
5.0
Forward Voltage[V]
Lead Temperature[℃]
■Ambient Temperature vs. Forward Current
■ Luminous Spectrum
40
1.2
1.0
0.8
0.6
0.4
0.2
0.0
30
20
10
0
-20
0
20
40
60
80
400 450 500 550 600 650 700
Ambient Temperature[℃]
0
■ Spatial Distribution
- 30
30
- 60
60
- 90
90
1
1
0.5
0
0.5
Data subject to change.
MODEL : ATPG-L53C
7. Inspection Standards
7 - 1 In production line, 100% inspection for electro-optical characteristics should
be done on following 3 items.
- VF , IR , Iv
7 - 2 Outgoing inspection be done to the standards as below.
- MIL-STD-104D, S-3, AQL 1.0%
- Items: VF, IR, Iv, λp
8. Packing Standards
8 – 1.Taping :
Standard taping provided. Or user’s request.
8 – 2 Bulk Packing :
In one vinyl pack, 500 or 1,000 LEDs are inserted. Or user’s request.
9. Caution on usage
9 - 1 Be careful never to exceed , even momentarily, the absolute maximum ratings
specified in the data sheet.
9 - 2 ACROSENTEC will not be held responsible for any damage to the user that
may result from accidents or any other reasons during operation of the user such
as use in excess of the absolute maximum ratings, or not keeping the matters that
demand special attention.
9 - 3 Store and use where there is no corrosive gas.
9 - 4 The bending or cutting of the lead should be done in room temperature and no
force applied on the package.
Data subject to change.
Copyright ⓒ 2003 AcrosenTec Co.,Ltd, (www.AcrosenTec.com)
相关型号:
©2020 ICPDF网 联系我们和版权申明