852-11733 [ETC]
POE MCBASIC 2TX/SSFX-SM;PoE McBasic with LFPT
Operation Manual
International Headquarters
B&B Electronics Mfg. Co. Inc.
707 Dayton Road
Ottawa, IL 61350 USA
Phone (815) 433-5100 -- General Fax (815) 433-5105
Website: www.bb-elec.com
European Headquarters
B&B Electronics
Westlink Commercial Park
Oranmore, Co. Galway, Ireland
Phone +353 91-792444 -- Fax +353 91-792445
Website: www.bb-europe.com
© 2013 B&B Electronics – Revised Dec. 2013
Document Number: 52-80916-01_001
2
CONTENTS
FCC RADIO FREQUENCY INTERFERENCESTATEMENT................................... 4
WARRANTY .............................................................................................. 4
ABOUT THE POE MCBASIC WITH LFPT........................................................ 6
INSTALLATION .......................................................................................... 6
DIP SWITCH CONFIGURATION ................................................................... 7
POE RESET DSW............................................................................................. 7
FAR END FAULT (FEF)..................................................................................... 8
LED OPERATION........................................................................................ 9
LED FUNCTIONS ................................................................................................ 9
RJ-45 LED FUNCTIONS..................................................................................... 10
TROUBLESHOOTING.................................................................................11
SPECIFICATIONS FOR THE POE MCBASIC WITH LFPT..................................12
POE PRECAUTIONS (FOR INSIDE-A-BUILDING INSTALLATION ONLY)...........13
B&B ELECTRONICS TECHNICAL SUPPORT ..................................................13
FIBER OPTIC CLEANING GUIDELINES .........................................................13
ELECTROSTATIC DISCHARGE PRECAUTIONS ..............................................14
SAFETY CERTIFICATIONS...........................................................................15
3
FCC RADIO FREQUENCY
INTERFERENCESTATEMENT
This equipment has been tested and found to comply with the limits for a Class B
computing device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference when the
equipment is operated in a commercial environment. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential area is likely to
cause harmful interference in which the user will be required to correct the
interference at his own expense.
Any changes or modifications not expressly approved by the manufacturer could
void the user’s authority to operate the equipment.
The use of non-shielded I/O cables may not guarantee compliance with FCC RFI
limits. This digital apparatus does not exceed the Class B limits for radio noise
emission from digital apparatus set out in the Radio Interference Regulation of
the Canadian Department of Communications.
Le présent appareil numérique n’émet pas de bruits radioélectriques dépassant
les limites applicables aux appareils numériques de classe B prescrites dans le
Règlement sur le brouillage radioélectrique publié par le ministère des
Communications du Canada.
WARRANTY
Limited Lifetime Warranty
Effective for products of B&B Electronics shipped on or after May 1, 2013, B&B
Electronics warrants that each such product shall be free from defects in material
and workmanship for its lifetime. This limited lifetime warranty is applicable
solely to the original user and is not transferable.
This warranty is expressly conditioned upon proper storage, installation,
connection, operation and maintenance of products in accordance with their
written specifications.
Pursuant to the warranty, within the warranty period, B&B Electronics, at its
option will:
4
1. Replace the product with a functional equivalent;
2. Repair the product; or
3. Provide a partial refund of purchase price based on a depreciated value.
Products of other manufacturers sold by B&B Electronics are not subject to any
warranty or indemnity offered by B&B Electronics, but may be subject to the
warranties of the other manufacturers.
Notwithstanding the foregoing, under no circumstances shall B&B Electronics
have any warranty obligations or any other liability for: (i) any defects resulting
from wear and tear, accident, improper use by the buyer or use by any third
party except in accordance with the written instructions or advice of the B&B
Electronics or the manufacturer of the products, including without limitation
surge and overvoltage conditions that exceed specified ratings, (ii) any products
which have been adjusted, modified or repaired by any party other than B&B
Electronics or (iii) any descriptions, illustrations, figures as to performance,
drawings and particulars of weights and dimensions contained in the B&B
Electronics’ catalogs, price lists, marketing materials or elsewhere since they are
merely intended to represent a general idea of the products and do not form part
of this price quote and do not constitute a warranty of any kind, whether express
or implied, as to any of the B&B Electronics’ products.
THE REPAIR OR REPLACEMENT OF THE DEFECTIVE ITEMS IN ACCORDANCE
WITH THE EXPRESS WARRANTY SET FORTH ABOVE IS B&B ELECTRONIC’ SOLE
OBLIGATION UNDER THIS WARRANTY. THE WARRANTY CONTAINED IN THIS
SECTION SHALL EXTEND TO THE ORIGINAL USER ONLY, IS IN LIEU OF ANY AND
ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, AND ALL SUCH WARRANTIES
AND INDEMNITIES ARE EXPRESSLY DISCLAIMED, INCLUDING WITHOUT
LIMITATION (I) THE IMPLIED WARRANTIES OF FITNESS FOR A PARTICULAR
PURPOSE AND OF MERCHANTABILITY AND (II) ANY WARRANTY THAT THE
PRODUCTS ARE DO NOT INFRINGE OR VIOLATE THE INTELLECTUAL PROPERTY
RIGHTS OF ANY THIRD PARTY. IN NO EVENT SHALL B&B ELECTRONICS BE
LIABLE FOR LOSS OF BUSINESS, LOSS OF USE OR OF DATA INTERRUPTION OF
BUSINESS, LOST PROFITS OR GOODWILL OR OTHER SPECIAL, INCIDENTAL,
EXEMPLARY OR CONSEQUENTIAL DAMAGES. B&B ELECTRONIC SHALL
DISREGARD AND NOT BE BOUND BY ANY REPRESENTATIONS, WARRANTIES OR
INDEMNITIES MADE BY ANY OTHER PERSON, INCLUDING WITHOUT LIMITATION
EMPLOYEES, DISTRIBUTORS, RESELLERS OR DEALERS OF B&B ELECTRONIC
WHICH ARE INCONSISTENT WITH THE WARRANTY, SET FORTH ABOVE.
5
ABOUT THE POE MCBASIC WITH LFPT
The PoE McBasic with LFPT is a solution for network applications that require
power over Ethernet for locations inside buildings where Power Sourcing
Equipment (PSE)/ Power over Ethernet (PoE)/ is required to power an Ethernet
device. The standalone unit offers 3 ports: a 100 Mbps fixed fiber transceiver
(1x9) uplink for the network connection, one 10/100Base-T copper port that
provides PSE/PoE (IEEE802.3af), and one standard Ethernet 10/100 Mbps copper
port. This unmanaged unit provides both power and data to a remote device
over a standard CAT5 copper line, eliminating the need for a power connection to
the remote device. The PoE McBasic with LFPT provisions up to 15.4 watts on
one PSE copper port, and is powered by an internal power supply, supporting
100-240 VAC.
The copper ports autonegotiate to the connected device’s speed and duplex
mode:
10 Mbps or 100 Mbps, and HDX or FDX (including Flow Control). The PoE
McBasic with LFPT supports jumbo frames up to 10240.
INSTALLATION
PoE McBasic with LFPT is a compact media converter that can be installed as a
standalone, table-top device, with rackmount ears, or using a wallmount bracket.
The rackmount ears and wallmount bracket are optional accessories available
through B&B Electronics distributors.
Installation Tip
Several models of the PoE McBasic with LFPT support single-strand fiber for operation.
Since single-strand fiber products use optics that transmit and receive on two different
wavelengths, single-strand fiber products must be deployed in pairs. For example,
connect a PoE McBasic with LFPT , TX/SSLX-SM1310-SC (which has 1310 xmt and 1550
rcv) to a product which has 1550 xmt and 1310 rcv, and is a single strand 10/100
MediaConverter that offers TX/SSLX/SM1550-SC. The two connected products must
also have the same speed and distance capabilities (i.e. both are single-mode [20km]
or both are single/PLUS [40km]).
6
DIP SWITCH CONFIGURATION
DIP Switch
1
Name
Description
Default Setting DIP Switch
OFF
PoE Reset
ON forces Port
2, PSE/PoE, to
OFF on LOS of
Fiber input
2
3
LFPT Port 1
LFPT Port 2
ON enables LFPT OFF
for Port 1 and
the FX Port
ON enables LFPT OFF
for Port 2 and
the FX Port
4
5
6
7
8
Factory Set
Factory Set
Factory Set
Factory Set
Factory Set
Do not change
Do not change
Do not change
Do not change
Do not change
OFF
OFF
OFF
OFF
OFF
POE RESET DSW
When set to ON, it will force the PSE output power on the copper port OFF when
the LINK state is lost on the fiber segment. By default, the DSW is set to OFF.
7
Link Fault Pass-Through (LFPT) DSW for PoE McBasic with LFPT
There are two DIP Switches for LFPT, each located near the copper (TX) ports.
LFPT is a diagnostic feature that when enable, allows a fault to be passed
through the unit. When enabled, if link is lost on the FX (fiber) port, the transmit
on the TX (copper) port is disabled. If link is lost on a TX port, the transmit on
the FX Port is disabled.
NOTE
Regarding the fault DIP Switches – PoE Reset, LFPT Port1 and LFPT Port 2: only one
fault condition is recognized at a time. The first fault condition to occur is in charge.
So if TX Port1 has no link and then the FX Port loses link, the loss of TX on Port 1 link
causes the FX Port to disable the transmit.
FAR END FAULT (FEF)
Far End Fault is a troubleshooting feature for the fiber segment that is
permanently enabled. If one strand of fiber fails, the error is reported back
down the other strand of fiber in the form of an FEF signal.
8
LED OPERATION
The PoE McBasic with LFPT includes LEDs for three ports, as shown below:
NOTE
The fixed twisted pair port labeled PSE is the only port capable of providing Power
Over Ethernet.
LED FUNCTIONS
FLT
Glows red when a fault has been detected on the fiber
port of the unit
LNK
Glows green with a valid link
100 Mbps
Glows green when is running at 100 Mbps
PWR
Glows green when unit is powered
9
RJ-45 LED FUNCTIONS
LNK/ACT
(TX1/TX2)
PSE
Glows green with a valid link
Blinks green when activity is detected
Glows green when port is supplying PoE power
Blinks green during fault conditions: 1 Hz flashes indicates an
overload or short; 4 Hz flashes indicates out of range voltage or
over-temperature
(TX2)
Off if the port is not supplying power
FDX
Glows amber when port is running full duplex
(TX1)
10
TROUBLESHOOTING
•
PWR LED glows green when the unit is powered. If this LED is not lit,
contact B&B Electronics Support.
•
Blinks green during fault conditions: 1 Hz flashes indicate an overload or
short; 4 Hz flashes indicate out of range voltage or over-temperature.
•
The PSE LED should maintain solid green, to indicate consistent power.
Check the PD device and its requirements.
The following table lists the pin configuration for the RJ-48 connector.
Pin# Signal Name
1000M
Signal Direction
10/100M
Out*
PoE
(ALT-B)
1
2
3
4
5
6
7
8
TXD1+
TXD1-
RXD2+
D3+
D3-
RXD2-
D4+
Out*
IN*
+V
+V
In*
-V
-V
D4-
11
SPECIFICATIONS FOR THE POE MCBASIC WITH
LFPT
Ethernet Connections
10/100BaseT
Auto Negotiation
AutoCross
Flow Control
10240 MTU
Full Line-Rate Forwarding
Input Specifications
100 to 240 ±10% VAC input, 50/60 Hz, 0.5A to 0.2A
Operating Temperature
+32°F to +122°F (0°C to +50°C)
Storage Temperature
-40°F to +185°F (-40°C to +85°C)
Humidity
5% to 95% (non-condensing); 0 to 10,000 ft. altitude
Dimensions
1.46” H x 4.76” W x 7.32” D (3.71 x 12.09 X 18.59 cm)
Power Characteristics
Consumes less than 10 watts (heating) plus PSE power
IEEE802.3af Power to field < 15.4 watts
Standards Compliance
IEEE 802.3af Power Over Ethernet
IEEE 802.3 Ethernet Standards
IEEE 802.3u Auto-Negotiation
RFC-2474
RFC-2475 DiffServ QoS
12
POE PRECAUTIONS (FOR INSIDE-A-BUILDING
INSTALLATION ONLY)
The PoE McBasic with LFPT is for inside-a-building installation only. It cannot be
installed in an outside-a-building environment, as it cannot meet the PoE
requirements, per the PoE standard. If installing the device outside, serious
damage can occur and void the B&B Electronics’ warranty.
B&B ELECTRONICS TECHNICAL SUPPORT
Phone: 1-800-346-3119 (Monday-Friday, 7:00 a.m. -6:30 p.m. CST)
Fax:
815-433-5109
Customer Service: orders@bb-elec.com
Tech Support: support@bb-elec.com
General Inquiries: info@bb-elec.com
FIBER OPTIC CLEANING GUIDELINES
Fiber Optic transmitters and receivers are extremely susceptible to
contamination by particles of dirt or dust, which can obstruct the optic path and
cause performance degradation. Good system performance requires clean optics
and connector ferrules.
1. Use fiber patch cords (or connectors, if you terminate your own fiber) only
from a reputable supplier; low-quality components can cause many hard-to-
diagnose problems in an installation.
2. Dust caps are installed at B&B Electronics to ensure factory-clean optical
devices. These protective caps should not be removed until the moment of
connecting the fiber cable to the device. Should it be necessary to disconnect
the fiber device, reinstall the protective dust caps.
13
3. Store spare caps in a dust-free environment such as a sealed plastic bag or
box so that when reinstalled they do not introduce any contamination to the
optics.
4. If you suspect that the optics have been contaminated, alternate between
blasting with clean, dry, compressed air and flushing with methanol to remove
particles of dirt.
ELECTROSTATIC DISCHARGE PRECAUTIONS
Electrostatic discharge (ESD) can cause damage to any product, add-in modules
or stand-alone units, containing electronic components. Always observe the
following precautions when installing or handling these kinds of products
1. Do not remove unit from its protective packaging until ready to install.
2. Wear an ESD wrist grounding strap before handling any module or
component. If the wrist strap is not available, maintain grounded contact with
the system unit throughout any procedure requiring ESD protection.
3. Hold the units by the edges; do not touch the electronic components or gold
connectors.
4. After removal, always place the boards on a grounded, static-free surface,
ESD pad or in a proper ESD bag. Do not slide the modules or stand-alone units
over any surface.
WARNING! Integrated circuits and fiber optic components are
extremely susceptible to electrostatic discharge damage. Do not
handle these components directly unless you are a qualified service
technician and use tools and techniques that conform to accepted
industry practices.
14
SAFETY CERTIFICATIONS
UL/CUL:
Listed to Safety of Information Technology Equipment, including
Electrical Business Equipment.
CE: The products described herein comply with the Council Directive on
Electromagnetic Compatibility (2004/108/EC) and the Council Directive on
Electrical Equipment Designed for use within Certain Voltage Limits
(2006/95/EC). Certified to Safety of Information Technology Equipment,
Including Electrical Business Equipment. For further details, contact B&B
Electronics.
Class 1 Laser product, Luokan 1
European Directive 2002/96/EC (WEEE) requires that any equipment that bears
this symbol on product or packaging must not be disposed of with unsorted
municipal waste. This symbol indicates that the equipment should be disposed
of separately from regular household waste. It is the consumer’s responsibility
to dispose of this and all equipment so marked through designated collection
facilities appointed by government or local authorities. Following these steps
through proper disposal and recycling will help prevent potential negative
consequences to the environment and human health. For more detailed
information about proper disposal, please contact local authorities, waste
disposal services, or the point of purchase for this equipment.
15
相关型号:
©2020 ICPDF网 联系我们和版权申明