5962-9960801HXC [ETC]
DC to DC Converter ; 直流到直流转换器\n
| 型号： | 5962-9960801HXC |
| 厂家： | 
ETC |
| 描述： | DC to DC Converter
|
| 文件： | 总19页 (文件大小：88K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
REVISIONS
LTR
DESCRIPTION
DATE (YR-MO-DA)
APPROVED
REV
SHEET
REV
SHEET
15
16
17
18
REV STATUS
OF SHEETS
REV
SHEET
1
2
3
4
5
6
7
8
9
10
11
12
13
14
PMIC N/A
PREPARED BY
Steve Duncan
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43216
STANDARD
MICROCIRCUIT DRAWING
CHECKED BY
Michael Jones
THIS DRAWING IS
AVAILABLE
FOR USE BY ALL
APPROVED BY
Raymond Monnin
MICROCIRCUIT, HYBRID, LINEAR, 5 VOLT,
SINGLE CHANNEL, DC/DC CONVERTER
DEPARTMENTS
AND AGENCIES OF THE
DEPARTMENT OF DEFENSE
DRAWING APPROVAL DATE
00-08-09
AMSC N/A
REVISION LEVEL
SIZE
A
CAGE CODE
5962-99608
67268
SHEET
1 OF 18
DSCC FORM 2233
APR 97
5962-E468-00
DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited.
1. SCOPE
1.1 Scope. This drawing documents five product assurance classes, class D (lowest reliability), class E, (exceptions), class G
(lowest high reliability), class H (high reliability), and class K, (highest reliability) and a choice of case outlines and lead finishes are
available and are reflected in the Part or Identifying Number (PIN). When available, a choice of radiation hardness assurance levels
are reflected in the PIN.
1.2 PIN. The PIN shall be as shown in the following example:
5962
-
½
½
½
99608
01
½
½
H
½
½
X
½
½
½
X
½
½
½
½
½
½
½
½
Federal
stock class
designator
\
RHA
designator
(see 1.2.1)
Device
type
(see 1.2.2)
Device
class
designator
(see 1.2.3)
Case
outline
(see 1.2.4)
Lead
finish
(see 1.2.5)
/
\/
Drawing number
1.2.1 Radiation hardness assurance (RHA) designator. RHA marked devices shall meet the MIL-PRF-38534 specified RHA
levels and shall be marked with the appropriate RHA designator. A dash (-) indicates a non-RHA device.
1.2.2 Device type(s). The device type(s) identify the circuit function as follows:
Device type
01
Generic number
AFL12005S/CH
Circuit function
DC/DC converter, 80 W, 5 V output
1.2.3 Device class designator. This device class designator shall be a single letter identifying the product assurance level as
follows:
Device class
Device performance documentation
D, E, G, H, or K
Certification and qualification to MIL-PRF-38534
1.2.4 Case outline(s). The case outline(s) are as designated in MIL-STD-1835 and as follows:
Outline letter
Descriptive designator
Terminals
Package style
U
X
Y
Z
See figure 1
See figure 1
See figure 1
See figure 1
12
12
12
12
Y case configuration with leads bent upwards
Straight leads with end mounting thru holes
Straight leads with side mounting thru holes
Y case configuration with leads bent downwards
1.2.5 Lead finish. The lead finish shall be as specified in MIL-PRF-38534.
SIZE
STANDARD
MICROCIRCUIT DRAWING
5962-99608
A
REVISION LEVEL
SHEET
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43216-5000
2
DSCC FORM 2234
APR 97
1.3 Absolute maximum ratings. 1/
Input voltage range ................................................................................ -0.5 V dc to +180 V dc
Lead temperature (soldering, 10 seconds) ........................................... +300°C
Storage temperature range ................................................................... -65°C to +135°C
1.4 Recommended operating conditions.
Input voltage range ................................................................................ +80 V dc to +160 V dc
Output power 2/.................................................................................... £80 W
Case operating temperature range........................................................ -55°C to +125°C
2. APPLICABLE DOCUMENTS
2.1 Government specification, standards, and handbook. The following specification, standards, and handbook form a part of
this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those listed in the issue
of the Department of Defense Index of Specifications and Standards (DoDISS) and supplement thereto, cited in the solitation.
SPECIFICATION
DEPARTMENT OF DEFENSE
MIL-PRF-38534 - Hybrid Microcircuits, General Specification for.
STANDARDS
DEPARTMENT OF DEFENSE
MIL-STD-883 - Test Method Standard Microcircuits.
MIL-STD-1835 - Interface Standard for Microcircuit Case Outlines.
HANDBOOK
DEPARTMENT OF DEFENSE
MIL-HDBK-103 - List of Standard Microcircuit Drawings (SMD's).
MIL-HDBK-780 - Standard Microcircuit Drawings.
(Unless otherwise indicated, copies of the specification, standards, and handbooks are available from the Standardization
Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.)
2.2 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text of
this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific
exemption has been obtained.
1/Stresses above the absolute maximum rating may cause permanent damage to the device. Extended operation at the
maximum levels may degrade performance and affect reliability.
2/Derate output power linearly above case temperature +125°C to 0 at +135°C.
SIZE
STANDARD
5962-99608
A
MICROCIRCUIT DRAWING
REVISION LEVEL
SHEET
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43216-5000
3
DSCC FORM 2234
APR 97
3. REQUIREMENTS
3.1 Item requirements. The individual item performance requirements for device classes D, E, G, H, and K shall be in
accordance with MIL-PRF-38534. Compliance with MIL-PRF-38534 may include the performance of all tests herein or as
designated in the device manufacturer's Quality Management (QM) plan or as designated for the applicable device class.
Therefore, the tests and inspections herein may not be performed for the applicable device class (see MIL-PRF-38534).
Furthermore, the manufacturers may take exceptions or use alternate methods to the tests and inspections herein and not perform
them. However, the performance requirements as defined in MIL-PRF-38534 shall be met for the applicable device class.
3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as specified in
MIL-PRF-38534 and herein.
3.2.1 Case outline(s). The case outline(s) shall be in accordance with 1.2.4 herein and figure 1.
3.2.2 Terminal connections. The terminal connections shall be as specified on figure 2.
3.3 Electrical performance characteristics. Unless otherwise specified herein, the electrical performance characteristics are as
specified in table I and shall apply over the full specified operating temperature range.
3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table II. The electrical tests
for each subgroup are defined in table I.
3.5 Marking of Device(s). Marking of device(s) shall be in accordance with MIL-PRF-38534. The device shall be marked with
the PIN listed in 1.2 herein. In addition, the manufacturer's vendor similar PIN may also be marked.
3.6 Data. In addition to the general performance requirements of MIL-PRF-38534, the manufacturer of the device described
herein shall maintain the electrical test data (variables format) from the initial quality conformance inspection group A lot sample, for
each device type listed herein. Also, the data should include a summary of all parameters manually tested, and for those which, if
any, are guaranteed. This data shall be maintained under document revision level control by the manufacturer and be made
available to the preparing activity (DSCC-VA) upon request.
3.7 Certificate of compliance. A certificate of compliance shall be required from a manufacturer in order to supply to this drawing.
The certificate of compliance (original copy) submitted to DSCC-VA shall affirm that the manufacturer's product meets the
performance requirements of MIL-PRF-38534 and herein.
3.8 Certificate of conformance. A certificate of conformance as required in MIL-PRF-38534 shall be provided with each lot of
microcircuits delivered to this drawing.
4. QUALITY ASSURANCE PROVISIONS
4.1 Sampling and inspection. Sampling and inspection procedures shall be in accordance with MIL-PRF-38534 or as modified
in the device manufacturer's Quality Management (QM) plan. The modification in the QM plan shall not affect the form, fit, or
function as described herein.
SIZE
STANDARD
5962-99608
A
MICROCIRCUIT DRAWING
REVISION LEVEL
SHEET
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43216-5000
4
DSCC FORM 2234
APR 97
TABLE I. Electrical performance characteristics.
Test
Symbol
Conditions
Group A
Subgroups
Device
type
Limits
Unit
-55°C £ T £ +125°C
C
VIN = 120 V dc ±5%, CL = 0
unless otherwise specified
Min
Max
5.05
Output voltage
VOUT
IOUT = 16 A
1
01
4.95
4.90
V
A
2,3
5.10
16
30
±20
±50
30
40
3
Output current 1/
Output ripple voltage 2/
Line regulation 3/
Load regulation 3/
Input current
IOUT
VIN = 80, 120, and 160 V dc
1,2,3
1,2,3
1,2,3
1,2,3
1
01
01
01
01
01
VRIP
VIN = 80, 120, and 160 V dc,
B.W. = 20 Hz to 10 MHz
mV p-p
mV
VRLINE
VRLOAD
IIN
VIN = 80, 120, and 160 V dc,
IOUT = 0, 8, and 16 A
VIN = 80, 120, and 160 V dc,
IOUT = 0, 8, and 16 A
mV
IOUT = no load
mA
2,3
Enable 1, (pin 4) shorted to
Input return (pin 2)
1,2,3
1,2,3
1,2,3
1,2,3
1
Enable 2, (pin 12) shorted to
Output return (pin 8)
5
Input ripple current 2/
Efficiency
IRIP
IOUT = 16 A,
B.W. = 20 Hz to 10 MHz
01
01
01
60
mA p-p
%
EFF
ISO
IOUT = 16 A
78
Isolation
Input to output or any pin to
case (except pin 3) at 500 V dc,
TC =+25°C
100
MW
Maximum capacitive
Load 5/
CL
No effect on dc performance, TC
=+25°C
4
01
10,000
mF
See footnotes at end of table.
SIZE
STANDARD
MICROCIRCUIT DRAWING
5962-99608
A
REVISION LEVEL
SHEET
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43216-5000
5
DSCC FORM 2234
APR 97
TABLE I. Electrical performance characteristics - Continued.
Test
Symbol
Conditions
Group A
Subgroups
Device
type
Limits
Unit
-55°C £ T £ +125°C
C
VIN = 120 V dc ±5%, CL = 0
unless otherwise specified
Min
Max
32
Power dissipation load fault
Current limit point 4/
PD
Overload 6/
1,2,3
01
01
W
A
Short circuit
32
ICL
VOUT = 90 % VNOM
1
2
18.4
20.0
20.0
16.8
18.4
3
23.2
Switching frequency
Sync frequency range
FS
IOUT = 16 A
IOUT = 16 A
4,5,6
4,5,6
4,5,6
01
01
01
500
600
700
kHz
FSYNC
500
kHz
Output response to step
transient load changes 7/
VOTLOAD 50% to/from 100%
10% to/from 50%
-450
+450
mV pk
-450
+450
200
Recovery time, step transient
load changes
TTLOAD
50% to/from 100%
4,5,6
01
ms
7/ 8/
10% to/from 50%
400
Output response to transient
step line changes 5/ 9/
VOTLINE
Input step 160 V to/from
400 V dc, IOUT = 16 A
4,5,6
4,5,6
01
01
-500
+500
mV pk
Recovery time transient step
line changes 5/ 8/ 9/
TTLINE
Input step, 160 V to/from
400 V dc, IOUT = 16 A
500
ms
Turn on overshoot
Turn on delay 10/
Load fault recovery 5/
VTonos
TonD
TrLF
IOUT = 0 and 16 A
IOUT = 0 and 16 A
4,5,6
4,5,6
4,5,6
01
01
01
250
120
120
mV pk
ms
ms
See footnotes at top of next page.
SIZE
STANDARD
MICROCIRCUIT DRAWING
5962-99608
A
REVISION LEVEL
SHEET
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43216-5000
6
DSCC FORM 2234
APR 97
TABLE I. Electrical performance characteristics - Continued.
1/ Parameter guaranteed by line and load regulation tests.
2/ Bandwidth guaranteed by design. Tested for 20 kHz to 10 MHz.
3/ All electrical tests are performed with remote sense leads connected to the output lead at the output load.
4/ Current limit point is that condition of excess load causing output voltage to drop 90% of nominal.
5/ Parameter shall be tested as part of design characterization and after design or process changes. Thereafter,
parameters shall be guaranteed to the limits specified in table I.
6/ An overload is that condition with a load in excess of the rated load but less than that necessary to trigger the short
circuit protection and is the condition of maximum power dissipation.
7/ Load step transition time ³ 10 microseconds.
8/ Recovery time is measured from the initiation of the transient to where VOUT has returned to within ± 1 percent of
VOUT at 50 percent load.
9/ Input step transition time ³ 100 microseconds.
10/ Turn on delay is measured with an input voltage rise time of between 100 and 500 volts per millisecond.
SIZE
STANDARD
MICROCIRCUIT DRAWING
5962-99608
A
REVISION LEVEL
SHEET
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43216-5000
7
DSCC FORM 2234
APR 97
Case U
FIGURE 1. Case outline(s).
SIZE
STANDARD
MICROCIRCUIT DRAWING
5962-99608
A
REVISION LEVEL
SHEET
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43216-5000
8
DSCC FORM 2234
APR 97
Case U - Continued
Millimeters
Inches
Symbol
A
Min
Max
9.65
Min
Max
.380
2.805
2.505
.530
1.505
2.01
1.005
.055
.43
D
71.00
63.37
13.21
37.97
50.6
25.27
1.14
10.4
71.25
63.63
13.46
38.23
51.1
25.53
1.40
10.9
2.795
2.495
.520
1.495
1.99
.995
.045
.41
D1
D2
E
e1
e2
F
L
L1
q
5.46
5.72
.215
1.745
1.145
1.745
.24
.295
.370
.245
.035
.135
.225
1.755
1.155
1.755
.26
.305
.380
.255
.045
.145
44.32
29.08
44.32
6.1
7.49
9.40
6.22
0.89
3.43
44.58
29.34
44.58
6.6
7.75
9.65
6.48
1.14
3.68
q1
q2
q3
q4
q5
S
Æb
Æp
NOTES:
1. The U.S. government preferred system of measurement is the metric SI. This item was designed using inch-pound
units of measurement. In case of problems involving conflicts between the metric and inch-pound units, the inch-
pound units shall rule.
2. Lead identification for reference only.
3. Case outline weight: 92 grams maximum.
FIGURE 1. Case outline(s) - Continued.
SIZE
STANDARD
MICROCIRCUIT DRAWING
5962-99608
A
REVISION LEVEL
SHEET
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43216-5000
9
DSCC FORM 2234
APR 97
Case X
FIGURE 1. Case outline - Continued.
SIZE
STANDARD
MICROCIRCUIT DRAWING
5962-99608
A
REVISION LEVEL
SHEET
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43216-5000
10
DSCC FORM 2234
APR 97
Case X - Continued
Millimeters
Inches
Symbol
A
Min
Max
9.65
Min
Max
.380
D
76.07
63.37
76.33
63.63
75.57
38.23
5.21
2.995
2.495
3.005
2.505
2.975
1.505
.205
D1
D2
E
e1
F
37.97
4.95
1.14
1.495
.195
.045
1.40
.055
L
6.05
.238
L1
q
q1
S
5.46
69.98
31.88
6.22
5.72
.215
2.755
1.255
.245
.225
70.23
32.13
6.48
2.765
1.265
.255
0.89
3.12
1.14
3.38
.035
.123
.045
.133
Æb
Æp
NOTES:
1. The U.S. government preferred system of measurement is the metric SI. This item was designed using inch-pound
units of measurement. In case of problems involving conflicts between the metric and inch-pound units, the inch-
pound units shall rule.
2. Lead identification for reference only.
3. Case outline weight: 92 grams maximum.
FIGURE 1. Case outline(s) - Continued.
SIZE
STANDARD
MICROCIRCUIT DRAWING
5962-99608
A
REVISION LEVEL
SHEET
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43216-5000
11
DSCC FORM 2234
APR 97
Case Y
FIGURE 1. Case outline(s) – Continued.
SIZE
STANDARD
MICROCIRCUIT DRAWING
5962-99608
A
REVISION LEVEL
SHEET
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43216-5000
12
DSCC FORM 2234
APR 97
Case Y - Continued
Millimeters
Inches
Symbol
A
D
D1
E
e1
e2
F
L
L1
q
q1
q2
q3
q4
q5
S
Min
Max
9.65
75.57
63.63
38.23
51.1
5.21
1.40
6.05
5.72
44.58
29.34
44.58
6.6
Min
Max
.380
2.975
2.505
1.505
2.01
.205
.055
.238
.225
1.755
1.155
1.755
.26
63.37
37.97
50.6
4.95
1.14
2.495
1.495
1.99
.195
.045
5.46
44.32
29.08
44.32
6.1
7.49
9.40
6.22
0.89
3.43
.215
1.745
1.145
1.745
.24
.295
.370
.245
.035
.135
7.75
9.65
6.48
1.14
3.68
.305
.380
.255
.045
.145
Æb
Æp
NOTES:
1. The U.S. government preferred system of measurement is the metric SI. This item was designed using inch-pound
units of measurement. In case of problems involving conflicts between the metric and inch-pound units, the inch-
pound units shall rule.
2. Lead identification for reference only.
3. Case outline weight: 92 grams maximum.
FIGURE 1. Case outline(s) - Continued.
SIZE
STANDARD
MICROCIRCUIT DRAWING
5962-99608
A
REVISION LEVEL
SHEET
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43216-5000
13
DSCC FORM 2234
APR 97
Case Z
FIGURE 1. Case outline(s) - Continued.
SIZE
STANDARD
MICROCIRCUIT DRAWING
5962-99608
A
REVISION LEVEL
SHEET
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43216-5000
14
DSCC FORM 2234
APR 97
Case Z - Continued
Millimeters
Inches
Symbol
A
Min
Max
9.65
71.25
63.63
13.46
38.23
51.1
25.53
1.40
9.4
Min
Max
.380
2.805
2.505
.530
1.505
2.01
1.005
.055
.37
D
71.00
63.37
13.21
37.97
50.6
25.27
1.14
8.9
2.795
2.495
.520
1.495
1.99
.995
.045
.35
D1
D2
E
e1
e2
F
L
L1
q
5.46
44.32
29.08
44.32
6.1
7.49
9.40
6.22
0.89
3.43
5.72
44.58
29.34
44.58
6.6
7.75
9.65
6.48
1.14
3.68
.215
1.745
1.145
1.745
.24
.295
.370
.245
.035
.135
.225
1.755
1.155
1.755
.26
.305
.380
.255
.045
.145
q1
q2
q3
q4
q5
S
Æb
Æp
NOTES:
1. The U.S. government preferred system of measurement is the metric SI. This item was designed using inch-pound
units of measurement. In case of problems involving conflicts between the metric and inch-pound units, the inch-
pound units shall rule.
2. Lead identification for reference only.
3. Case outline weight: 92 grams maximum.
FIGURE 1. Case outline(s) - Continued.
SIZE
STANDARD
MICROCIRCUIT DRAWING
5962-99608
A
REVISION LEVEL
SHEET
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43216-5000
15
DSCC FORM 2234
APR 97
Device type
Case outlines
01
U,X,Y,Z
Terminal number
Terminal symbol
1
2
Positive Input
Input Return
Case
3
4
Enable 1
5
Sync Output
Sync Input
Positive Output
Output Return
Return Sense
Positive Sense
Share
6
7
8
9
10
11
12
Enable 2
FIGURE 2. Terminal connections.
SIZE
STANDARD
MICROCIRCUIT DRAWING
5962-99608
A
REVISION LEVEL
SHEET
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43216-5000
16
DSCC FORM 2234
APR 97
TABLE II. Electrical test requirements.
MIL-PRF-38534 test requirements
Subgroups
(in accordance with
MIL-PRF-38534, group A test
table)
Interim electrical parameters
Final electrical parameters
Group A test requirements
---
1*, 2, 3, 4, 5, 6
1, 2, 3, 4, 5, 6
1, 4
Group C end-point electrical
Parameters
MIL-STD-883, group E end-point
electrical parameters for RHA
devices
Not applicable
* PDA applies to subgroup 1.
4.2 Screening. Screening shall be in accordance with MIL-PRF-38534. The following additional criteria shall apply:
a. Burn-in test, method 1015 of MIL-STD-883.
(1) Test condition A, B, C, or D. The test circuit shall be maintained by the manufacturer under document revision level
control and shall be made available to either DSCC-VA or the acquiring activity upon request. Also, the test circuit shall
specify the inputs, outputs, biases, and power dissipation, as applicable, in accordance with the intent specified in test
method 1015 of MIL-STD-883.
(2) T as specified in accordance with table I of method 1015 of MIL-STD-883.
A
b.Interim and final electrical test parameters shall be as specified in table II herein, except interim electrical parameter tests
prior to burn-in are optional at the discretion of the manufacturer.
4.3 Conformance and periodic inspections. Conformance inspection (CI) and periodic inspection (PI) shall be in accordance
with MIL-PRF-38534 and as specified herein.
4.3.1 Group A inspection (CI). Group A inspection shall be in accordance with MIL-PRF-38534 and as follows:
a. Tests shall be as specified in table II herein.
b.Subgroups 7, 8, 9, 10, and 11 shall be omitted.
4.3.2 Group B inspection (PI). Group B inspection shall be in accordance with MIL-PRF-38534.
SIZE
STANDARD
5962-99608
A
MICROCIRCUIT DRAWING
REVISION LEVEL
SHEET
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43216-5000
17
DSCC FORM 2234
APR 97
4.3.3 Group C inspection (PI). Group C inspection shall be in accordance with MIL-PRF-38534 and as follows:
a. End-point electrical parameters shall be as specified in table II herein.
b.Steady-state life test, method 1005 of MIL-STD-883.
(1) Test condition A, B, C, or D. The test circuit shall be maintained by the manufacturer under document revision level
control and shall be made available to either DSCC-VA or the acquiring activity upon request. Also, the test circuit shall
specify the inputs, outputs, biases, and power dissipation, as applicable, in accordance with the intent specified in test
method 1005 of MIL-STD-883.
(2) T as specified in accordance with table I of method 1005 of MIL-STD-883.
A
(3) Test duration: 1,000 hours, except as permitted by method 1005 of MIL-STD-883.
4.3.4 Group D inspection (PI). Group D inspection shall be in accordance with MIL-PRF-38534.
4.3.5 Radiation Hardness Assurance (RHA) inspection. RHA inspection is not currently applicable to this drawing.
5. PACKAGING
5.1 Packaging requirements. The requirements for packaging shall be in accordance with MIL-PRF-38534.
6. NOTES
6.1 Intended use. Microcircuits conforming to this drawing are intended for use for Government microcircuit applications (original
equipment), design applications, and logistics purposes.
6.2 Replaceability. Microcircuits covered by this drawing will replace the same generic device covered by a contractor-prepared
specification or drawing.
6.3 Configuration control of SMD's. All proposed changes to existing SMD's will be coordinated as specified in MIL-PRF-38534.
6.4 Record of users. Military and industrial users shall inform Defense Supply Center Columbus when a system application
requires configuration control and the applicable SMD. DSCC will maintain a record of users and this list will be used for
coordination and distribution of changes to the drawings. Users of drawings covering microelectronic devices (FSC 5962) should
contact DSCC-VA, telephone (614) 692-0544.
6.5 Comments. Comments on this drawing should be directed to DSCC-VA, Columbus, Ohio 43216-5000, or telephone (614)
692-0512.
6.6 Sources of supply. Sources of supply are listed in MIL-HDBK-103 and QML-38534. The vendors listed in MIL-HDBK-103
and QML-38534 have submitted a certificate of compliance (see 3.7 herein) to DSCC-VA and have agreed to this drawing.
SIZE
STANDARD
5962-99608
A
MICROCIRCUIT DRAWING
REVISION LEVEL
SHEET
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43216-5000
18
DSCC FORM 2234
APR 97
STANDARD MICROCIRCUIT DRAWING BULLETIN
DATE: 00-08-09
Approved sources of supply for SMD 5962-99608 are listed below for immediate acquisition information only and shall
be added to MIL-HDBK-103 and QML-38534 during the next revisions. MIL-HDBK-103 and QML-38534 will be revised
to include the addition or deletion of sources. The vendors listed below have agreed to this drawing and a certificate of
compliance has been submitted to and accepted by DSCC-VA. This bulletin is superseded by the next dated revisions
of MIL-HDBK-103 and QML-38534.
Standard
microcircuit drawing
PIN 1/
Vendor
CAGE
Number
Vendor
Similar
PIN 2/
5962-9960801HUA
5962-9960801HUC
5962-9960801HXA
5962-9960801HXC
5962-9960801HYA
5962-9960801HYC
5962-9960801HZA
5962-9960801HZC
52467
52467
52467
52467
52467
52467
52467
52467
AFL12005SW/CH
AFL12005SW/CH
AFL12005SX/CH
AFL12005SX/CH
AFL12005SY/CH
AFL12005SY/CH
AFL12005SZ/CH
AFL12005SZ/CH
1/ The lead finish shown for each PIN representing hermetic package is the most
readily available from the manufacturer listed for that part. If the desired lead finish
is not listed contact the vendor to determine its availability.
2/ Caution. Do not use this number for item acquisition. Items acquired to this number
may not satisfy the performance requirements of this drawing.
Vendor CAGE
number
Vendor name
and address
52467
Lambda Advanced Analog Incorporated
2270 Martin Avenue
Santa Clara, CA 95050-2781
The information contained herein is disseminated for convenience only and the
Government assumes no liability whatsoever for any inaccuracies in the
information bulletin.
相关型号：
©2020 ICPDF网 联系我们和版权申明