5333V8 [ETC]
Infrared Receiver Modules ; 红外接收器模块\n型号: | 5333V8 |
厂家: | ETC |
描述: | Infrared Receiver Modules
|
文件: | 总4页 (文件大小:59K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
INFRARED RECEIVER MODULE
MIM-5xx3V8
Description
The MIM-5xx3V8 is miniaturized infrared receivers for
remote control and other applications requiring improved
ambient light rejection.
The separate PIN diode and preamplifier IC are assembled
on a single leadframe.
The epoxy package contains a special IR filter.
This module has excellent performance even in disturbed
ambient light applications and provides protection against
uncontrolled output pulses.
Features
* Photo detector and preamplifier in one package
* Internal filter for PCM frequency
* High immunity against ambient light
* Improved shielding against electric field disturbance
* 5.0-Volt supply voltage; low power consumption
* TTL and CMOS compatibility
MIM-5xx3V8 Series Models
l MIM-5303V8 30KHz
l MIM-5333V8 33KHz
l MIM-5363V8 36KHz
l MIM-5383V8 38KHz
l MIM-5403V8 40KHz
l MIM-5443V8 44KHz
l MIM-5563V8 56KHz
Unit : mm
BLOCK DIAGRAM
VS
CGA &
filter
Demodulator
mC
Input
AGC / ATC & digital
control
Oscillator
GND
REV: A1
Unity Opto Technology Co., Ltd.
07/08/2003
MIM-5xx3V8
@ Ta=25oC
Absolute Maximum Ratings
Item
Supply voltage
Symbol
VCC
Topr
Ratings
5.5
Unit
V
oC
oC
oC
Remark
Operating temperature
Storage temperature
Soldering temperature
-10 ~ + 75
-10 ~ + 75
260
Tstg
Tsd
t<=10 s, 1mm from case
Electro-optical characteristics (Vcc=5.0V)
Parameter
Current consumption
Symbol
Icc
Min.
Typ.
1.4
Max.
2.0
Unit
mA
Remarks
Under no signal
Response wavelength
Tuning frequency
l p
940
nm
f0
KHZ
30,33,36,38,40,44,56
Output form
- - - - - active low output - - - - -
V0h
V0l
H level output voltage
L level output voltage
H level output pulse width
L level output pulse width
Distance between emitter & detector
Half angle
4.2
V
V
0.5
Twh
Twl
L1
400
400
800
800
ms
ms
m
10.0
Note 1
Dq
±45
deg
Horizonal direction
Test Method
A. Standard Transmitter
25cm
ON/OFF pulse width satisfied from 25 cm to detection limit
+5.0V
600ms
10kW
10mF
carrier frequency f0
duty 50%
Transmitter
Duty 50%
Vout
600ms
600ms
GND
Oscilloscope
Fig 1. Burst Wave
Fig 2. Standard Transmitter Measurement circuit
B. Detection Length Test
Vout
q
Transmitter output
D.U.T
q: indicates horizontal and vertical directions
L
REV: A1
07/08/2003
Unity Opto Technology Co., Ltd.
MIM-5xx3V8
C . Pulse Width Test
Transmitter output
DUT output pulse
600ms 600ms
Twl
Twh
V0h
V0l
Application Circuit
100W*)
Vcc (+5V)
3
4.7mF *)
MIM-5xx3V8
>10kW
optional
MIE-544A2
mC
1
2
GND
*) recommended to suppress power supply disturbances
CHARACTERISTIC CURVES (TA=25oC)
900
800
700
600
500
400
1.8
Burst length * 600ms, cycle = 1.2ms
tpw: Average value of output from start
of signal input to 60th pulse
1.6
1.4
1.2
1.0
0.1
1
10
Input Level (mVp-p
100
1000
6
3
4
5
7
)
Supply Voltage Vcc (V)
INPUT LEVEL vs.OUTPUT PULSE WIDTH
SUPPLY VOLTAGE vs. SUPPLY CURRENT
NOTE 1. Distance between emitter & detector specifies maximum distance that output wave form satisfies
the standard under the conditions below against the standerd transmitter.
(1)Measuring place ………Indoor without extreme reflection of light.
(2)Ambient light source… Detecting surface illumination shall be 200±50Lux under ordinary
hite fluorescense lamp of no high frequency lighting.
(3)Standard transmitter … Burst wave indicated in Fig 1. of standard transmitter
shall be arranged to 50mVp-p under the measuring circuit specified in Fig 2.
REV: A1
Unity Opto Technology Co., Ltd.
07/08/2003
MIM-5xx3V8
Reliability
Test item
Test condition
Standard
Ta=+60oC Vcc=5.0 V
t=240H
t=240H
t=240H
High temparature
High temp. & high humi.
Low temparature
Heat cycle
Note 2.
Note 2.
Note 2.
Note 2.
Note 3.
Ta=+40oC 90%RH Vcc=5.0V
Ta= -10oC Vcc=5.0V
-20oC(0.5H) ~ +75oC(0.5H) 20cycle
Dropping
Test devices shall be dropped 3 times naturally
onto hard wooden board from a 75cm height position.
NOTE 2. (electro-optical charactistics) shall be satisfied after leaving 2 hours in the normal temperature .
NOTE 3. (electro-optical charactistics) shall be satisfied and no conoid deforms
and destructions of appearance .(excepting deforms of terminals)
Inspection standard
1.Among electrical characteristics , total number shall be inspected on items blow.
1-1 front distance between emitter & detector
1-2 Current consumption
1-3 H level output voltage
1-4 L level output voltage
2.Items except above mentioned are not inspected particularly , but shall fully satisfy
CAUTION ( When use and storage of this device )
1.Store and use where there is no force causing transformation or change in quality .
2.Store and use where there is no corrosive gas or sea(salt) breeze .
3.Store and use where there is no extreme humidity .
4.Solder the lead-pin within the condition of ratings. After soldering do not add extra force .
5.Do not wash this device . Wipe the stains of diode side with a soft cloth. You can
use the solvent , ethylalcohol or methylalcohol or isupropylene only .
6.To prevent static electricity damage to the Pre-AMP make sure that the human body
, the soldering iron is connected to ground before using .
7.Put decoupling device between Vcc and GND for reduse the noise from power supply line .
8.The performance of remote-control system depends on environments condition and ability
of periferal parts. Customer should evaluate the performance as total system in those conditions
after system up with components such as commander , micon and this receiver module .
Guarantee period and scope
1.Guarantee period
One year after delivery to desired place .
2.Guarantee scope
A re-delivery of goods will be carried out if the cause of malfunction lies in our
device .However no responsibilities be taken for the inconveniences caused by
the malfunction of our devices .
Others
1.This device is not design to endure radiative rays and heavily charged particles .
2.In case where any trouble or questions arise,both parties agress to make full discussion
covering the said problem .
REV: A1
Unity Opto Technology Co., Ltd.
07/08/2003
相关型号:
©2020 ICPDF网 联系我们和版权申明