EL6283CU [ELANTEC]
3-Channel Laser Diode Driver w/Oscillator & APC Amplifier; 3通道激光二极管驱动器瓦特/振荡器和放大器APC
| 型号： | EL6283CU |
| 厂家： | 
ELANTEC SEMICONDUCTOR |
| 描述： | 3-Channel Laser Diode Driver w/Oscillator & APC Amplifier |
| 文件： | 总2页 (文件大小：43K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
EL6283C - Product Brief
3-Channel Laser Diode Driver w/Oscillator & APC Amplifier
Features
General Description
• Shrink-Small Outline Package
The EL6283C is a high-performance three channel laser driver that
provides controlled current to a grounded laser diode. Write channels
2 and 3 can provide up to 200mA per channel of DC or pulsed current,
with switching speeds of approximately one nanosecond rise/fall time.
All three channels are summed together at the IOUT output, allowing
the user to create multilevel waveforms in order to optimize laser
diode performance. The level of the output current is set by an analog
voltage applied to an external resistor which converts the voltage into
a current at the IIN pin (virtually ground). The current seen at this pin
• Voltage-controlled output current
source to 200mA per channel,
requiring one external set resistor
per channel
• Current-controlled output current
source to 200mA per channel
• Rise time = 0.8ns
• Fall time = 0.8ns
is then amplified to become a current source at pin IOUT
.
• On chip oscillator with frequency
and amplitude control by use of
external resistors to ground
• Oscillator to 500MHz
• Oscillator to 100mA pk/pk
• Single +5V supply (±10%)
An on-chip 500MHz oscillator is provided to allow output current
modulation when in any mode. This is turned on when the OSCEN pin
is held high. Complete control of amplitude and frequency is set by
two external resistors connected to ground at pins RFREQ and RAMP
(see graphs in this data sheet for further explanation).
• Disable feature for power-up
protection and power savings
• Fast Settling APC Amplifier
Output current pulses are enabled when an ‘L’ signal is applied to the
OUTEN pin. No output current flows when OUTEN is ‘H’, and addi-
tional laser diode protection is provided since the OUTEN input will
float high when open. Complete IOUT shut-off is also achieved by
holding the ENABLE pin low, which will override all other control
pins.
Applications
• CD-RW applications
• Writable optical drives
• Laser diode current switching
The EL6283C also includes a fast settling APC amplifier designed to
interface directly with the front end monitor diode and the sample-
and-hold amplifier for read and write power control. Its 100MHz
bandwidth and 30ns settling time enable up to 16X CD-RW design.
Ordering Information
Part No
Temp. Range
Package
Outline #
EL6283CU
0°C to +70°C
QSOP-16
MDP0041
Connection Diagram
1
2
3
4
5
6
7
8
VOUT
VREF
IINR
PDIN 16
VCC 15
IOUT 14
RFREQ
IIN2
GND 13
RAMP 12
ENABLE 11
OSCEN 10
IIN3
OUTEN3
OUTEN2
9
VCC
Note: All information contained in this data sheet has been carefully checked and is believed to be accurate as of the date of publication; however, this data sheet cannot be a “controlled document”. Current revisions, if any, to these
specifications are maintained at the factory and are available upon your request. We recommend checking the revision level before finalization of your design documentation.
© 2000 Elantec Semiconductor, Inc.
EL6283C - Product Brief
3-Channel Laser Diode Driver w/Oscillator & APC Amplifier
General Disclaimer
Specifications contained in this data sheet are in effect as of the publication date shown. Elantec, Inc. reserves the right to make changes in the cir-
cuitry or specifications contained herein at any time without notice. Elantec, Inc. assumes no responsibility for the use of any circuits described
herein and makes no representations that they are free from patent infringement.
WARNING - Life Support Policy
Elantec, Inc. products are not authorized for and should not be used
within Life Support Systems without the specific written consent of
Elantec, Inc. Life Support systems are equipment intended to sup-
port or sustain life and whose failure to perform when properly used
in accordance with instructions provided can be reasonably
expected to result in significant personal injury or death. Users con-
templating application of Elantec, Inc. Products in Life Support
Systems are requested to contact Elantec, Inc. factory headquarters
to establish suitable terms & conditions for these applications. Elan-
tec, Inc.’s warranty is limited to replacement of defective
Elantec Semiconductor, Inc.
675 Trade Zone Blvd.
Milpitas, CA 95035
Telephone: (408) 945-1323
(888) ELANTEC
Fax:
(408) 945-9305
components and does not cover injury to persons or property or
other consequential damages.
European Office: +44-118-977-6080
Japan Technical Center: +81-45-682-5820
Printed in U.S.A.
2
相关型号：
©2020 ICPDF网 联系我们和版权申明