FM-9032LM-5AN [E-OEC]
IR Receiver Modules for Remote Control Systems; 红外接收器模块的远程控制系统
| 型号： | FM-9032LM-5AN |
| 厂家： | 
OPTO ELECTRONICS CO,. LTD |
| 描述： | IR Receiver Modules for Remote Control Systems |
| 文件： | 总7页 (文件大小：838K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
FM-9038LM-5AN
IR Receiver Modules for Remote Control Systems
Description
The FM-9038LM-5AN is remote control receiver modules.
Pin diode and receiver IC are assembled on one module.
Small-sized, light-weight, and low current consumption.
modules have been achieved by using resin mold.
The demodulated output signal can directly be decoded
by a microprocessor. The main benefit is the reliable
function even in disturbed ambient and the protection
against uncontrolled output pulses.
Features
Supply Voltage Range: 2.7V to 6.5V
TTL and CMOS compatibility
Photo detector and preamplifier in one package.
Internal filter for PCM frequency
Open collector output (built-in Pull-up resistor(40K)
Output active low
Enhanced Immunity against all kinds of disturbance light
No occurrence of disturbance pulses at output pin within nominal conditions.
Short settling time after power On.( below 1msec)
Meet RoHS
Application Circuit
47~100Ω
VCC
VCC
IR Receiver Module
47uf
Transmitter
MCU
VOUT
GND
GND
R-C filter recommended to suppress power supply disturbances.
R-C filter should be connected closely between VCC pin and GND pin.
Block Diagram
Ordering Info.(carrier frequencies)
Type
Carrier Frequency (fo)
32.7 K
FM-9032LM-5AN
FM-9036LM-5AN
FM-9038LM-5AN
FM-9040LM-5AN
FM-9056LM-5AN
36.7 K
37.9 K
40.0 K
56.7 K
光電企業有限公司
November 2006 Rev 1.3
FM-9038LM-5AN
Absolute Maximum Ratings
(Ta = 25℃)
Parameter
Supply Voltage
Symbol
VCC
Ratings
Unit
V
7.0
0.2 ~Vcc
Output Voltage
VOUT
IOUT
Topr
V
Output Current
2.5
mA
℃
℃
℃
Operating Temperature
Storage Temperature
Soldering Temperature
-20 ~ +80
-30 ~ +85
260℃, Max 5 sec
Tstg
Tsd
Electro-optical Characteristics
(Ta = 25℃)
Parameter
Symbol
Min.
Typ.
Max.
Unit
Supply Voltage
Supply Current
Max input current
Vcc
ICC
IIN
2.7
5.0
1.0
1.0
-
6.5
1.3
1.5
-
V
mA
mA
V
No input signal
Vin=0
0.8
0.5
Voh
Vol
Vcc-0.5
Vcc=5V
Output Voltage
-
-
0.2
940
0.4
-
V
Peak Wave Length
nm
λp
±0˚
-
-
-
15
10
7
-
-
-
m
m
m
Fig.
1,2,3
Arrival Distance
L
±30˚
±45˚
fin=37.9kHz
Max. Voltage Gain
Internal Pull-up Resistor
BPF Bandwidth
Av
70
36
76
40
82
44
dB
㏀
Vin=30㎶pp
Rpul
fbw
fc
fin=37.9kHz
-
3.5
fo
-
kHz
%
Vin=30㎶pp
BPF frequency
-3.5
450
+3.5
750
Fig.
1,2,6
Output Pulse width
Tpw
600
㎲
光電企業有限公司
November 2006 Rev 1.3
FM-9038LM-5AN
[ Fig.1 ] Data Signal diagram
t Pause
Data Word
enlarge
Carrier Frequency : fo
t Gap
t Burst
(Output pulse)
t Gap : Signal gap time between two burst in pulses of carrier. Minimum Gap Time ≧ 300us
t Burst : Length of a burst in pulses of the carrier frequency. Minimum Burst ≧ 300us
t pause : Data pause between two data words. Minimum Data PauseTime ≧ 20ms
[ Fig.2 ] Transmitter
10K
VCC
PD
S/Transmitter
100uf
VOUT
GND
10K
30㎝
※ The specifications shall be satisfied under the following conditions. The standard transmitter
shall be specified of the burst wave form adjusted to VOUT 200mVp-p upon Po measuring
circuit Standard Transmitter
[ Fig.3 ] Test condition of arrival distance
Vout
osc
Transmitter
GND
Vcc
: Indicates horizontal and
vertical directions
[ Measurement condition for arrival distance ]
☞ Ambient light source : Detecting surface illumination shall be irradiate 200±50Lux
under ordinary white fluorescence lamp without high frequency lighting
光電企業有限公司
November 2006 Rev 1.3
FM-9038LM-5AN
Electrical/Optical Characteristics
[ Fig.5 ] Sensitivity vs. Supply Voltage
[ Fig.4 ] Supply Current vs. Voltage
100
80
60
40
20
2.5
2.0
1.5
1.0
0.5
0
0.0
2.5 3.0 3.5 4.0 4.5 5.0 5.5 6.0 6.5
Supply Voltage(V)
2.5 3.0 3.5 4.0 4.5 5.0 5.5 6.0 6.5
Supply Voltage(V)
[ Fig.6 ] Output Pulse Width vs. Distance
[ Fig.7 ] Directivity (Horizontal/Vertical)
0˚
20˚
900
800
700
600
500
400
300
40˚
100
90
60˚
80˚
V
H
80 60 40 20
0
0
4
8
12
16
20
24
28
Relative Sensitivity(%)
Transmission Distance(m)
ESD Test Results
[ Fig.8 ] BPF Fc Curve
BPF fc
1.2
1
Parameter
Conditions
Specification
Results
Machine
Model
C=200㎊
Min ±200V
>±200V
0.8
0.6
0.4
0.2
0
R=0Ω
Human
Body
Model
C=100pf
R=1.5KΩ
Min ±2000V
>±2000V
0.5 0.6 0.7 0.8 0.9
1
1.1 1.2 1.3 1.4 1.5
f/fo Relative Frequency
光電企業有限公司
November 2006 Rev 1.3
FM-9038LM-5AN
光電企業有限公司
November 2006 Rev 1.3
FM-9038LM-5AN
◆ Recommended Soldering Condition
Flow Soldering Condition
2. Recommendation Flow Soldering condition Temp & Time
光電企業有限公司
November 2006 Rev 1.3
FM-9038LM-5AN
1. Packing unit for Remote control module
Partial
Shipment of
Outer Box
Packing Units / Poly Bag/ Max Devices / Max Inner Box /
Package
Device
Method
Tube
Inner Box
Inner Box
Outer Box
Transfer mold
Type
Poly Bag
200
5
1000
10
* Inner Box # 1 * Inner Box # 1 * Outer Box # 2 * Outer Box # 3
(unit : mm)
Inner Box #1 with Opto-Sensor Logo (170*240*65)
Outer Box #2 with Opto-Sensor Logo (365*360*270)
Outer Box #3 with Opto-Sensor Logo (385*750*300)
2. Packing method
1) Input max 200 units to one Poly bag and label should be attached middle of it.
Antistatic Vinyl
2) Input 5 poly bags to one inner box and label should be attached as below.
Label #1
<Inner Box # 1>
3) Input 10 inner boxes to outer box.
<Outer Box # 2>
4) Input 2 outer boxes into Box #3.
<Outer Box # 3>
光電企業有限公司
November 2006 Rev 1.3
相关型号：
©2020 ICPDF网 联系我们和版权申明