AH3563Q-P-A [DIODES]
HIGH VOLTAGE HIGH SENSITIVITY AUTOMOTIVE HALL EFFECT LATCH SWITCH;
| 型号： | AH3563Q-P-A |
| 厂家： | 
DIODES INCORPORATED |
| 描述： | HIGH VOLTAGE HIGH SENSITIVITY AUTOMOTIVE HALL EFFECT LATCH SWITCH 高压 |
| 文件： | 总14页 (文件大小：662K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
AH3563Q
HIGH VOLTAGE HIGH SENSITIVITY
AUTOMOTIVE HALL EFFECT LATCH SWITCH
Description
Pin Assignments
The AH3563Q is an AECQ100-qualified high-voltage, high-sensitivity
Hall effect omnipolar switch IC designed for position and proximity
sensing in automotive applications, such as in seat and seatbelt
buckle, steering lock/immobilization, gear stick, transmission actuator
and gear position, HVAC compression, wiper, door/trunk closure, and
so on. To support a wide range of demanding applications, the design
is optimized to operate over the supply range of 3.0V to 28V. With
chopper-stabilized architecture and an internal bandgap regulator to
provide temperature compensated supply for internal circuits, the
AH3563Q provides a reliable solution over the whole operating range.
For robustness and protection, the device has a reverse blocking
diode with a zener clamp on the supply. The output has an
overcurrent limit and a zener clamp.
(Top View)
3 OUTPUT
1 VDD
GND 2
SOT23
(Top View)
3. OUTPUT
2. GND
VDD
The single open-drain output can be switched on with south or north
pole of sufficient strength. When the magnetic flux density (B)
perpendicular to the package is larger than the operate point (BOP),
the output is switched on (pulled low) and is held on until the
magnetic flux density B is lower than the release point (BRP).
1.
SIP-3 (Bulk Pack)
Applications
Features
Omnipolar Operation
•
•
•
•
•
•
•
•
Position and Proximity Sensing in Automotive Applications
•
•
•
•
High Sensitivity: BOP and BRP of ±30G and ±20G Typical
Internally Pull-up Resistor on the Output with Overcurrent Limit
3.0V to 28V Operating Voltage Range
Open and Close Detect
Position Detect
Level Detect
Chopper Stabilized Design Provides
Flow Meters
o
o
o
Superior Temperature Stability
Minimal Switch Point Drift
Contactless Switches
Seatbelt Buckle
Seat Position
Enhanced Immunity to Stress
•
•
•
•
•
•
Good RF Noise Immunity
Reverse Blocking Diode
Zener Clamp on Supply and Output Pins
-40°C to +150°C Operating Temperature
ESD: HBM ＞ 8kV, CDM: > 2kV
Industry Standard SOT23 and SIP-3 (Ammo Pack), SIP-3 (Bulk
Pack) Packages
•
Totally Lead-Free & Fully RoHS Compliant (Notes 1 & 2)
Halogen and Antimony Free. “Green” Device (Note 3)
•
Notes:
1. No purposely added lead. Fully EU Directive 2002/95/EC (RoHS), 2011/65/EU (RoHS 2) & 2015/863/EU (RoHS 3) compliant.
2. See https://www.diodes.com/quality/lead-free/ for more information about Diodes Incorporated’s definitions of Halogen- and Antimony-free, "Green" and
Lead-free.
3. Halogen- and Antimony-free "Green” products are defined as those which contain <900ppm bromine, <900ppm chlorine (<1500ppm total Br + Cl) and
<1000ppm antimony compounds.
1 of 14
www.diodes.com
July 2018
© Diodes Incorporated
AH3563Q
Document number: DS40865 Rev. 1 - 2
AH3563Q
Typical Applications Circuit
3.0V to 28V
VDD
OUTPUT
AH3563Q
CIN
GND
Note:
4. CIN is for power stabilization and to strengthen the noise immunity; the recommended capacitance is 10nF ~ 100nF.
Pin Descriptions
Package: SOT23 and SIP-3 (Ammo Pack), SIP-3 (Bulk Pack)
Pin Number
Pin Name
VDD
Function
1
2
3
Power Supply Input
Ground
GND
OUTPUT Output Pin
Functional Block Diagram
VDD
t
e
s
Power
switch
f
f
n
O
d
n
a
o
i
c
i
t
a
l
m
a
n
y
r
l
e
l
To All Subcircuits
Control
e
t
e
c
n
a
p
l
w
i
o
F
L
m
a
D
s
C
S
d
l
H
OUTPUT
s
a
-
o
P
Amp
Amp
Current
Limit
GND
2 of 14
www.diodes.com
July 2018
© Diodes Incorporated
AH3563Q
Document number: DS40865 Rev. 1 - 2
AH3563Q
Absolute Maximum Ratings (Note 5 & 6) (@TA = +25°C, unless otherwise specified.)
Symbol
VDD
Characteristic
Value
32
Unit
V
Supply Voltage (Note 6)
Reverse Supply Voltage (Note 6)
Output Off Voltage (Note 6)
Continuous Output Current
-32
32
V
VDDR
V
VOUT_MAX
IOUT
IOUT_R
B
60
mA
Reverse Output Current
Magnetic Flux Density
-50
mA
Unlimited
SIP-3 (Ammo Pack),
SIP-3 (Bulk Pack)
550
Package Power Dissipation
mW
PD
SOT23
230
Ts
Storage Temperature Range
-65 to +165
°C
°C
kV
V
Maximum Junction Temperature
+150
8
TJ
ESD HBM
ESD MM
ESD CDM
Electros Static Discharge Withstand—Human Body Model (HMB)
Electros Static Discharge Withstand— Machine Model (MM)
800
2
Electros Static Discharge Withstand— Charged Device Model (CDM)
kV
Notes:
5. Stresses greater than the 'Absolute Maximum Ratings' specified above may cause permanent damage to the device. These are stress ratings only;
functional operation of the device at these or any other conditions exceeding those indicated in this specification is not implied. Device reliability may be
affected by exposure to absolute maximum rating conditions for extended periods of time.
6. The absolute maximum VDD of 32V is a transient stress rating and is not meant as a functional operating condition. It is not recommended to operate
the device at the absolute maximum rated conditions for any period of time.
Recommended Operating Conditions (@TA = -40°C to +150°C, unless otherwise specified.)
Symbol
VDD
Parameter
Supply Voltage
Operating Temperature Range
Condition
Rating
3.0 to 28
Unit
V
Operating
Operating
-40 to +150
°C
TA
Electrical Characteristics (Note 7 & 8) (@TA = -40°C to +150°C, VDD = 3V to 28V, unless otherwise specified.)
Symbol
Parameter
Output ON Voltage
Condition
IOUT = 20mA, B > BOP
Min
Typ
Max
Unit
VOUT_ON
—
0.2
0.4
V
Output Leakage Current
(When Output is Off)
ILKG
—
0.1
10
µA
VOUT = 28V, B < BRP, Output Off
—
—
—
—
—
—
—
—
3
3.5
4
mA
mA
µA
µA
µA
µA
µs
Output Open, TA = +25°C
Output Open, TA = -40°C to +150°C
VDD = -18V, TA = +25°C
VDD = -18V, TA = -40°C to +150°C
VDD = -28V, TA = +25°C
VDD = -28V, TA = -40°C to +150°C
VDD >= 3V, B > BOP (Note 7)
—
Supply Current
IDD
—
0.6
0.6
1.6
1.6
10
—
1500
—
IDD_R
Reverse Supply Current
2500
—
Device Power-On Time (Start-up Time)
Chopping Frequency
tP_ON
fC
—
800
kHz
Response Time Delay
(Time from Magnetic Threshold Reached (Note 9)
to the start of the Output Rise or Fall)
Output Rising Time
—
—
—
3.75
0.2
—
1
µs
µs
µs
tD
tR
tF
(External Pull-up Resistor RL and Load
Capacitance Dependent)
RL = 1kΩ, CL = 20pF
Output Falling Time
(Internal Switch Resistance and Load
Capacitance Dependent)
0.1
1
RL = 1kΩ, CL = 20pF
Output Current Limit
Zener Clamp Voltage
30
28
—
—
55
—
mA
V
IOCL
VZ
B > BOP, (Note 10 )
IDD = 5mA
Notes:
7. When power is initially turned on, VDD must be within its correct operating range (3.0V to 28V) to guarantee the output sampling. The output state is valid
after the start-up time of 10µs typical from the operating voltage reaching 3V.
8. Typical values are defined at TA = +25°C, VDD = 12V. Maximum and minimum values over the operating temperature range is not tested in production but
guaranteed by design, process control, and characterization.
9. Guaranteed by design, process control, and characterization. Not tested in production.
10. The device will limit the output current IOUT to current limit of IOC.
3 of 14
www.diodes.com
July 2018
© Diodes Incorporated
AH3563Q
Document number: DS40865 Rev. 1 - 2
AH3563Q
Magnetic Characteristics (Note 11 &12) (TA = -40°C to +150°C, VDD = 3.0V to 28V, unless otherwise specified.)
(1mT=10 Gauss)
Symbol
Parameter
Condition
Min
—
15
—
-45
—
5
Typ
30
Max
—
Unit
V
DD = 12V, TA = +25°C
BOPS (South Pole to the Part Marking Side)
30
45
—
TA = -40°C to +150°C
VDD = 12V, TA = +25°C
TA = -40°C to +150°C
VDD = 12V, TA = +25°C
TA = -40°C to +150°C
VDD = 12V, TA = +25°C
TA = -40°C to +150°C
VDD = 12V, TA = +25°C
TA = -40°C to +150°C
Operation Point
-30
-30
20
BOPN (North Pole to the Part Marking Side)
BRPS (South Pole to the Part Marking Side)
BRPN (South Pole to the Part Marking Side)
BHY (|BOPX|-|BRPX|)
-15
—
Gauss
20
35
—
Release Point
—
-35
—
5
-20
-20
10
-5
—
Hysteresis (Note 13)
10
18
Notes:
11. When power is initially turned on, VDD must be within its correct operating range (3.0V to 28V) to guarantee the output sampling. The output state is valid
after the start-up time of 10µs typical from the operating voltage reaching 3V.
12. Typical values are defined at TA = +25°C, VDD = 12V. Maximum and minimum values over the operating temperature range is not tested in production but
guaranteed by design, process control and characterization.
13. Maximum and minimum hysteresis is guaranteed by design, process control and characterization.
Output
(off-state)
VDD
(off-state)
Turn
on
Turn
off
Bhy
Turn
on
Turn
off
Bhy
(on-state)
VOUT_ON = VSAT
VSAT
0
Bops
Brps
Bopn Brpn
( Magnetic Flux Density B )
S
S
N
Part mark
Part mark
N
SIP-3 (Ammo Pack)
SIP-3 (Bulk Pack)
(SOT23)
4 of 14
www.diodes.com
July 2018
© Diodes Incorporated
AH3563Q
Document number: DS40865 Rev. 1 - 2
AH3563Q
Typical Operating Characteristics
Output Switch Operate and Release Points (Magnetic Thresholds)—BOPs and BRPs
Supply Current
5 of 14
www.diodes.com
July 2018
© Diodes Incorporated
AH3563Q
Document number: DS40865 Rev. 1 - 2
AH3563Q
Typical Operating Characteristics (continued)
Supply Reverse Current
Output Switch On Voltage
Output Switch Leakage Current
6 of 14
www.diodes.com
July 2018
© Diodes Incorporated
AH3563Q
Document number: DS40865 Rev. 1 - 2
AH3563Q
Typical Operating Characteristics (cont.)
Output Current Limit
7 of 14
www.diodes.com
July 2018
© Diodes Incorporated
AH3563Q
Document number: DS40865 Rev. 1 - 2
AH3563Q
Thermal Performance Characteristics
(1) Package Type: SOT23
25
50
60
70
80
85
90
100
105
110
120
125
130
140
150
TA (°C)
230
184
166
147
129
120
110
92
83
74
55
46
37
18
0
PD (mW)
Power Dissipation Curve
300
200
100
0
-40
25
50
75
100
125
150
Ambient Temperature TA (oC)
(2) Package Type: SIP-3 (Ammo Pack), SIP-3 (Bulk Pack)
25
50
60
70
80
85
90
100
105
110
120
125
130
140
150
TA (°C)
550
440
396
362
308
286
264
220
198
176
132
110
88
44
0
PD (mW)
PD (mW)
Power Dissipation Curve
600
500
400
300
200
100
0
-40
25
50
75
100
125
150
TA (°C)
8 of 14
www.diodes.com
July 2018
© Diodes Incorporated
AH3563Q
Document number: DS40865 Rev. 1 - 2
AH3563Q
Ordering Information
AH3563Q - X - X
Package
Packing
Product Name
7 : Tape & Reel
A: Ammo Box (Note 14)
B: Bulk (Note 15)
P : SIP-3(Ammo Pack)
P : SIP-3(Bulk Pack)
SA : SOT23
Bulk
7” Tape and Reel
Ammo Box
Packag
Part Number
Packaging
Quantity
Part Number
Suffix
Part Number Quantity Part Number
e Code
Quantity
Suffix
Suffix
AH3563Q-P-A
AH3563Q-P-B
AH3563Q-SA-7
P
P
SIP-3 (Ammo Pack)
SIP-3 (Bulk Pack)
SOT23
NA
1000
NA
NA
-B
NA
NA
NA
4000/Box
NA
-A
NA
NA
NA
NA
SA
NA
3000/Tape & Reel
-7
Notes:
14. Ammo Box is for SIP-3 (Ammo Pack) Spread Lead.
15. Bulk is for SIP-3 (Bulk Pack) Straight Lead.
Marking Information
(1) Package Type: SOT23
( Top View )
XX : Identification code
Y : Year 0 to 9
W : Week : A to Z : 1 to 26 week;
XX Y W X
a to z : 27 to 52 week; z represents
52 and 53 week
X : Internal code
Part Number
Package
Identification Code
AH3563Q
SOT23
Z3
(2) Package Type: SIP-3 (Ammo Pack), SIP-3 (Bulk Pack
( Top View )
Y : Year : 0~9
WW : Week : 01~52, "52" represents
Part Number
3563Q
Y WW X
52 and 53 week
X : Internal Code
Part Number
AH3563Q
Package
Identification Code
3563Q
SIP-3 (Ammo Pack)
SIP-3 (Bulk Pack)
AH3563Q
3563Q
9 of 14
www.diodes.com
July 2018
© Diodes Incorporated
AH3563Q
Document number: DS40865 Rev. 1 - 2
AH3563Q
Package Outline Dimensions (All dimensions in mm.)
Please see http://www.diodes.com/package-outlines.html for the latest version.
(1) Package Type: SOT23
All 7°
H
SOT23
GAUGE PLANE
0.25
Dim
A
B
C
D
F
G
H
Min
Max
0.51
1.40
2.50
1.03 0.915
0.60 0.535
Typ
0.40
1.30
2.40
J
0.37
1.20
2.30
0.89
0.45
1.78
2.80
K
K1
a
M
A
L
L1
2.05
3.00
1.83
2.90
0.05
J
0.013 0.10
K
K1
L
L1
M
a
0.890 1.00 0.975
0.903 1.10 1.025
C
B
0.45
0.25
0.61
0.55
0.55
0.40
0.085 0.150 0.110
0° 8°
—
D
All Dimensions in mm
G
F
Min/Max
PART
MARKING
SURFACE
Die
Hall Sensor
Pin1
1.4/1.5
Sensor Location
10 of 14
www.diodes.com
July 2018
© Diodes Incorporated
AH3563Q
Document number: DS40865 Rev. 1 - 2
AH3563Q
Package Outline Dimensions (continued) (All dimensions in mm.)
Please see http://www.diodes.com/package-outlines.html for the latest version.
(2) Package Type: SIP-3 (Bulk Pack)
S
SIP-3 (Bulk Pack)
Min Max Typ
Dim
A
b
b2
c
D
E
e1
F
D
J
1.40 1.60 1.50
0.33 0.43 0.38
0.40 0.508 0.46
0.35 0.41 0.38
3.90 4.30 4.10
2.80 3.20 3.00
1.24 1.30 1.27
A
E
b2
L1
0.00 0.20
2.62 REF
--
J
L
L1
S
14.00 15.00 14.50
1.55 1.75 1.65
0.63 0.84 0.74
F
a1
a2
a3
a4
--
--
--
--
--
--
--
--
5°
5°
45°
L
3°
All Dimensions in mm
b
c
e1
Min/Max
0.63/0.84
0.27/0.48
1.90/2.10
1.05/1.25
Hall Sensor
PART
MARKING
SURFACE
D i e
PART
MARKING
SURFACE
2
1
3
Sensor Location
11 of 14
www.diodes.com
July 2018
© Diodes Incorporated
AH3563Q
Document number: DS40865 Rev. 1 - 2
AH3563Q
Package Outline Dimensions (cont.) (All dimensions in mm.)
Please see http://www.diodes.com/package-outlines.html for the latest version.
(3) Package Type: SIP-3 (Ammo Pack)
SIP-3
(Ammo Pack)
S
Dim
A
b
b2a
c
D
Min
Max Typ
1.40 1.60 1.50
0.33 0.43 0.38
0.40 0.52 0.46
0.35 0.41 0.38
3.90 4.30 4.10
2.80 3.20 3.00
1.24 1.30 1.27
2.40 2.90 2.65
D
A
J
E
E
e1
e2
F
J
L
La
L1
L3
S
a1
a2
a3
a4
b2a
F
L1
L3
0.00 0.20
2.62 REF
—
14.00 15.00 14.50
12.90 14.90 13.90
1.55 1.75 1.65
2.00 3.00 2.50
0.63 0.84 0.74
—
—
—
—
e1
La
L
—
—
—
—
5°
5°
45°
3°
All Dimensions in mm
e2
b
c
Min/Max
0.63/0.84
0.27/0.48
1.90/2.10
1.05/1.25
Hall Sensor
PART
MARKING
SURFACE
PART
MARKING
SURFACE
2
1
3
Sensor Location
12 of 14
www.diodes.com
July 2018
© Diodes Incorporated
AH3563Q
Document number: DS40865 Rev. 1 - 2
AH3563Q
Suggested Pad Layout
Please see http://www.diodes.com/package-outlines.html for the latest version.
(1) Package Type: SOT23
Y
Dimensions Value (in mm)
C
X
2.0
0.8
Y1
C
X1
Y
1.35
0.9
Y1
2.9
X
X1
13 of 14
www.diodes.com
July 2018
© Diodes Incorporated
AH3563Q
Document number: DS40865 Rev. 1 - 2
AH3563Q
IMPORTANT NOTICE
DIODES INCORPORATED MAKES NO WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, WITH REGARDS TO THIS DOCUMENT,
INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
(AND THEIR EQUIVALENTS UNDER THE LAWS OF ANY JURISDICTION).
Diodes Incorporated and its subsidiaries reserve the right to make modifications, enhancements, improvements, corrections or other changes
without further notice to this document and any product described herein. Diodes Incorporated does not assume any liability arising out of the
application or use of this document or any product described herein; neither does Diodes Incorporated convey any license under its patent or
trademark rights, nor the rights of others. Any Customer or user of this document or products described herein in such applications shall assume
all risks of such use and will agree to hold Diodes Incorporated and all the companies whose products are represented on Diodes Incorporated
website, harmless against all damages.
Diodes Incorporated does not warrant or accept any liability whatsoever in respect of any products purchased through unauthorized sales channel.
Should Customers purchase or use Diodes Incorporated products for any unintended or unauthorized application, Customers shall indemnify and
hold Diodes Incorporated and its representatives harmless against all claims, damages, expenses, and attorney fees arising out of, directly or
indirectly, any claim of personal injury or death associated with such unintended or unauthorized application.
Products described herein may be covered by one or more United States, international or foreign patents pending. Product names and markings
noted herein may also be covered by one or more United States, international or foreign trademarks.
This document is written in English but may be translated into multiple languages for reference. Only the English version of this document is the
final and determinative format released by Diodes Incorporated.
LIFE SUPPORT
Diodes Incorporated products are specifically not authorized for use as critical components in life support devices or systems without the express
written approval of the Chief Executive Officer of Diodes Incorporated. As used herein:
A. Life support devices or systems are devices or systems which:
1. are intended to implant into the body, or
2. support or sustain life and whose failure to perform when properly used in accordance with instructions for use provided in the
labeling can be reasonably expected to result in significant injury to the user.
B. A critical component is any component in a life support device or system whose failure to perform can be reasonably expected to cause the
failure of the life support device or to affect its safety or effectiveness.
Customers represent that they have all necessary expertise in the safety and regulatory ramifications of their life support devices or systems, and
acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any
use of Diodes Incorporated products in such safety-critical, life support devices or systems, notwithstanding any devices- or systems-related
information or support that may be provided by Diodes Incorporated. Further, Customers must fully indemnify Diodes Incorporated and its
representatives against any damages arising out of the use of Diodes Incorporated products in such safety-critical, life support devices or systems.
Copyright © 2018, Diodes Incorporated
www.diodes.com
14 of 14
www.diodes.com
July 2018
© Diodes Incorporated
AH3563Q
Document number: DS40865 Rev. 1 - 2
相关型号：
©2020 ICPDF网 联系我们和版权申明