CY8C21434-24LFXI [CYPRESS]
PSoC㈢ Mixed-Signal Array; 的PSoC ™混合信号阵列![CY8C21434-24LFXI](http://pdffile.icpdf.com/pdf1/p00119/img/icpdf/CY8C21001-24PVXI_654339_icpdf.jpg)
型号: | CY8C21434-24LFXI |
厂家: | ![]() |
描述: | PSoC㈢ Mixed-Signal Array |
文件: | 总42页 (文件大小:564K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
![](http://public.icpdf.com/style/img/ads.jpg)
PSoC® Mixed-Signal Array
Final Data Sheet
CY8C21234, CY8C21334,
CY8C21434, CY8C21534, and CY8C21634
Features
■
Powerful Harvard Architecture Processor
■
Flexible On-Chip Memory
■
Programmable Pin Configurations
❐
❐
❐
❐
M8C Processor Speeds to 24 MHz
Low Power at High Speed
❐
8K Flash Program Storage 50,000 Erase/Write
Cycles
❐
❐
25 mA Drive on All GPIO
Pull Up, Pull Down, High Z, Strong, or Open
Drain Drive Modes on All GPIO
❐
❐
❐
❐
❐
512 Bytes SRAM Data Storage
In-System Serial Programming (ISSP™)
Partial Flash Updates
2.4V to 5.25V Operating Voltage
❐
❐
Up to 8 Analog Inputs on GPIO
Operating Voltages Down to 1.0V Using
On-Chip Switch Mode Pump (SMP)
Configurable Interrupt on All GPIO
❐
Industrial Temperature Range: -40°C to +85°C
Flexible Protection Modes
■
■
Versatile Analog Mux
EEPROM Emulation in Flash
❐
❐
❐
Common Internal Analog Bus
■
Advanced Peripherals (PSoC Blocks)
Simultaneous Connection of IO Combinations
Capacitive Sensing Application Capability
■
Complete Development Tools
❐
4 Analog Type “E” PSoC Blocks Provide:
- 2 Comparators with DAC Refs
❐
Free Development Software
(PSoC Designer™)
Additional System Resources
- Single or Dual 8-Bit 28 Channel ADC
4 Digital PSoC Blocks Provide:
❐
Full-Featured, In-Circuit Emulator and
Programmer
2
❐
❐
I C™ Master, Slave and Multi-Master to
400 kHz
- 8- to 32-Bit Timers, Counters, and PWMs
- CRC and PRS Modules
❐
❐
❐
Full Speed Emulation
❐
❐
❐
❐
Watchdog and Sleep Timers
Complex Breakpoint Structure
128K Trace Memory
User-Configurable Low Voltage Detection
Integrated Supervisory Circuit
- Full-Duplex UART, SPI™ Master or Slave
- Connectable to All GPIO Pins
Complex Peripherals by Combining Blocks
■
Precision, Programmable Clocking
On-Chip Precision Voltage Reference
❐
❐
❐
Internal ±2.5% 24/48 MHz Oscillator
Internal Oscillator for Watchdog and Sleep
PSoC® Functional Overview
The PSoC® family consists of many Mixed-Signal Array with
On-Chip Controller devices. These devices are designed to
replace multiple traditional MCU-based system components
with one, low cost single-chip programmable component. A
PSoC device includes configurable blocks of analog and digital
logic, as well as programmable interconnect. This architecture
allows the user to create customized peripheral configurations,
to match the requirements of each individual application. Addi-
tionally, a fast CPU, Flash program memory, SRAM data mem-
ory, and configurable IO are included in a range of convenient
pinouts.
The PSoC architecture, as illustrated on the left, is comprised of
four main areas: the Core, the System Resources, the Digital
System, and the Analog System. Configurable global bus
resources allow all the device resources to be combined into a
complete custom system. Each CY8C21x34 PSoC device
includes four digital blocks and four analog blocks. Depending
on the PSoC package, up to 28 general purpose IO (GPIO) are
also included. The GPIO provide access to the global digital
and analog interconnects.
The PSoC Core
The PSoC Core is a powerful engine that supports a rich
instruction set. It encompasses SRAM for data storage, an
interrupt controller, sleep and watchdog timers, and IMO (inter-
nal main oscillator) and ILO (internal low speed oscillator). The
January 12, 2007
© Cypress Semiconductor Corp. 2004-2007 — Document No. 38-12025 Rev. *K
1
[+] Feedback
CY8C21x34 Final Data Sheet
PSoC® Overview
CPU core, called the M8C, is a powerful processor with speeds
up to 24 MHz. The M8C is a four MIPS 8-bit Harvard architec-
ture microprocessor.
Digital System Block Diagram
Port 3
Port 1
Port 2
Port 0
System Resources provide additional capability, such as digital
clocks to increase the flexibility of the PSoC mixed-signal
arrays, I2C functionality for implementing an I2C master, slave,
MultiMaster, an internal voltage reference that provides an
absolute value of 1.3V to a number of PSoC subsystems, a
switch mode pump (SMP) that generates normal operating volt-
ages off a single battery cell, and various system resets sup-
ported by the M8C.
DigitalClocks
FromCore
ToAnalog
System
To SystemBus
DIGITAL SYSTEM
DigitalPSoCBlockArray
Row 0
The Digital System is composed of an array of digital PSoC
blocks, which can be configured into any number of digital
peripherals. The digital blocks can be connected to the GPIO
through a series of global buses that can route any signal to any
pin. Freeing designs from the constraints of a fixed peripheral
controller.
4
4
DBB00
DBB01
DCB02
DCB03
8
8
8
8
The Analog System is composed of four analog PSoC blocks,
supporting comparators and analog-to-digital conversion up to
8 bits in precision.
GIE[7:0]
GIO[7:0]
GOE[7:0]
GOO[7:0]
Global Digital
Interconnect
The Digital System
The Digital System is composed of 4 digital PSoC blocks. Each
block is an 8-bit resource that can be used alone or combined
with other blocks to form 8, 16, 24, and 32-bit peripherals, which
are called user module references. Digital peripheral configura-
tions include those listed below.
The Analog System
The Analog System is composed of 4 configurable blocks,
allowing the creation of complex analog signal flows. Analog
peripherals are very flexible and can be customized to support
specific application requirements. Some of the common PSoC
analog functions for this device (most available as user mod-
ules) are listed below.
■ PWMs (8 to 32 bit)
■ PWMs with Dead band (8 to 32 bit)
■ Counters (8 to 32 bit)
■ Analog-to-digital converters (single or dual, with 8-bit resolu-
■ Timers (8 to 32 bit)
tion)
■ UART 8 bit with selectable parity
■ SPI master and slave
■ Pin-to-pin comparator
■ Single-ended comparators (up to 2) with absolute (1.3V) ref-
erence or 8-bit DAC reference
■ I2C slave and multi-master
■ Cyclical Redundancy Checker/Generator (8 to 32 bit)
■ IrDA
■ 1.3V reference (as a System Resource)
In most PSoC devices, analog blocks are provided in columns
of three, which includes one CT (Continuous Time) and two SC
(Switched Capacitor) blocks. The CY8C21x34 devices provide
limited functionality Type “E” analog blocks. Each column con-
tains one CT Type E block and one SC Type E block. Refer to
the PSoC Mixed-Signal Array Technical Reference Manual for
detailed information on the CY8C21x34’s Type E analog blocks.
■ Pseudo Random Sequence Generators (8 to 32 bit)
The digital blocks can be connected to any GPIO through a
series of global buses that can route any signal to any pin. The
buses also allow for signal multiplexing and for performing logic
operations. This configurability frees your designs from the con-
straints of a fixed peripheral controller.
Digital blocks are provided in rows of four, where the number of
blocks varies by PSoC device family. This allows you the opti-
mum choice of system resources for your application. Family
resources are shown in the table titled “PSoC Device Charac-
teristics” on page 3.
January 12, 2007
Document No. 38-12025 Rev. *K
2
[+] Feedback
CY8C21x34 Final Data Sheet
PSoC® Overview
Analog System Block Diagram
Additional System Resources
System Resources, some of which have been previously listed,
provide additional capability useful to complete systems. Addi-
tional resources include a switch mode pump, low voltage
detection, and power on reset. Brief statements describing the
merits of each system resource are presented below.
Array Input
Configuration
■ Digital clock dividers provide three customizable clock fre-
quencies for use in applications. The clocks can be routed to
both the digital and analog systems. Additional clocks can be
generated using digital PSoC blocks as clock dividers.
ACI0[1:0]
ACI1[1:0]
■ The I2C module provides 100 and 400 kHz communication
over two wires. Slave, master, and multi-master modes are
all supported.
All IO
X
X
■ Low Voltage Detection (LVD) interrupts can signal the appli-
cation of falling voltage levels, while the advanced POR
(Power On Reset) circuit eliminates the need for a system
supervisor.
AC OL 1MU X
X
X
An al o g MuxBus
X
Array
■ An internal 1.3 voltage reference provides an absolute refer-
ACE00
ACE01
ASE11
ence for the analog system, including ADCs and DACs.
■ An integrated switch mode pump (SMP) generates normal
operating voltages from a single 1.2V battery cell, providing a
low cost boost converter.
ASE10
■ Versatile analog multiplexer system.
PSoC Device Characteristics
The Analog Multiplexer System
Depending on your PSoC device characteristics, the digital and
analog systems can have 16, 8, or 4 digital blocks and 12, 6, or
4 analog blocks. The following table lists the resources
available for specific PSoC device groups. The PSoC device
covered by this data sheet is highlighted below.
The Analog Mux Bus can connect to every GPIO pin. Pins can
be connected to the bus individually or in any combination. The
bus also connects to the analog system for analysis with com-
parators and analog-to-digital converters. An additional 8:1 ana-
log input multiplexer provides a second path to bring Port 0 pins
to the analog array.
PSoC Device Characteristics
Switch control logic enables selected pins to precharge continu-
ously under hardware control. This enables capacitive mea-
surement for applications such as touch sensing. Other
multiplexer applications include:
PSoC Part
Number
up to
64
CY8C29x66
4
16
12
4
4
12
2K
32K
■ Track pad, finger sensing.
up to
44
256
Bytes
CY8C27x43
CY8C24x94
CY8C24x23A
2
1
1
8
4
4
12
48
12
4
2
2
4
2
2
12
6
16K
16K
4K
■ Chip-wide mux that allows analog input from any IO pin.
■ Crosspoint connection between any IO pin combinations.
56
1K
up to
24
256
Bytes
6
When designing capacitive sensing applications, refer to the
signal-to-noise system level requirement found in Application
Note AN2403 at http://www.cypress.com/design/AN2403 on the
Cypress web site.
up to
28
512
Bytes
a
CY8C21x34
CY8C21x23
CY8C20x34
1
1
0
4
4
0
28
8
0
0
0
2
2
0
8K
4K
8K
4
256
Bytes
a
16
4
up to
28
512
Bytes
b
28
3
a. Limited analog functionality.
b. Two analog blocks and one CapSense.
January 12, 2007
Document No. 38-12025 Rev. *K
3
[+] Feedback
CY8C21x34 Final Data Sheet
PSoC® Overview
Getting Started
Development Tools
PSoC Designer is a Microsoft® Windows-based, integrated
development environment for the Programmable System-on-
Chip (PSoC) devices. The PSoC Designer IDE and application
runs on Windows NT 4.0, Windows 2000, Windows Millennium
(Me), or Windows XP. (Reference the PSoC Designer Func-
tional Flow diagram below.)
The quickest path to understanding the PSoC silicon is by read-
ing this data sheet and using the PSoC Designer Integrated
Development Environment (IDE). This data sheet is an over-
view of the PSoC integrated circuit and presents specific pin,
register, and electrical specifications. For in-depth information,
along with detailed programming information, reference the
PSoC Mixed-Signal Array Technical Reference Manual, which
can be found on http://www.cypress.com/psoc.
PSoC Designer helps the customer to select an operating con-
figuration for the PSoC, write application code that uses the
PSoC, and debug the application. This system provides design
database management by project, an integrated debugger with
In-Circuit Emulator, in-system programming support, and the
CYASM macro assembler for the CPUs.
For up-to-date Ordering, Packaging, and Electrical Specification
information, reference the latest PSoC device data sheets on
the web at http://www.cypress.com.
Development Kits
PSoC Designer also supports a high-level C language compiler
developed specifically for the devices in the family.
Development Kits are available from the following distributors:
Digi-Key, Avnet, Arrow, and Future. The Cypress Online Store
contains development kits, C compilers, and all accessories for
PSoC development. Go to the Cypress Online Store web site at
http://www.cypress.com, click the Online Store shopping cart
icon at the bottom of the web page, and click PSoC (Program-
mable System-on-Chip) to view a current list of available items.
PSoC Designer Subsystems
Technical Training Modules
Free PSoC technical training modules are available for users
new to PSoC. Training modules cover designing, debugging,
advanced
analog
and
CapSense.
Go
to
http://
www.cypress.com/techtrain.
Consultants
Certified PSoC Consultants offer everything from technical
assistance to completed PSoC designs. To contact or become a
PSoC Consultant go to http://www.cypress.com, click on Design
Support located on the left side of the web page, and select
CYPros Consultants.
Technical Support
PSoC application engineers take pride in fast and accurate
response. They can be reached with a 4-hour guaranteed
response at http://www.cypress.com/support/login.cfm.
Application Notes
A long list of application notes will assist you in every aspect of
your design effort. To view the PSoC application notes, go to
the http://www.cypress.com web site and select Application
Notes under the Design Resources list located in the center of
the web page. Application notes are sorted by date by default.
January 12, 2007
Document No. 38-12025 Rev. *K
4
[+] Feedback
CY8C21x34 Final Data Sheet
PSoC® Overview
PSoC Designer Software Subsystems
Device Editor
Debugger
The device editor subsystem allows the user to select different
onboard analog and digital components called user modules
using the PSoC blocks. Examples of user modules are ADCs,
DACs, Amplifiers, and Filters.
The PSoC Designer Debugger subsystem provides hardware
in-circuit emulation, allowing the designer to test the program in
a physical system while providing an internal view of the PSoC
device. Debugger commands allow the designer to read the
program and read and write data memory, read and write IO
registers, read and write CPU registers, set and clear break-
points, and provide program run, halt, and step control. The
debugger also allows the designer to create a trace buffer of
registers and memory locations of interest.
The device editor also supports easy development of multiple
configurations and dynamic reconfiguration. Dynamic reconfig-
uration allows for changing configurations at run time.
PSoC Designer sets up power-on initialization tables for
selected PSoC block configurations and creates source code
for an application framework. The framework contains software
to operate the selected components and, if the project uses
more than one operating configuration, contains routines to
switch between different sets of PSoC block configurations at
run time. PSoC Designer can print out a configuration sheet for
a given project configuration for use during application pro-
gramming in conjunction with the Device Data Sheet. Once the
framework is generated, the user can add application-specific
code to flesh out the framework. It’s also possible to change the
selected components and regenerate the framework.
Online Help System
The online help system displays online, context-sensitive help
for the user. Designed for procedural and quick reference, each
functional subsystem has its own context-sensitive help. This
system also provides tutorials and links to FAQs and an Online
Support Forum to aid the designer in getting started.
Hardware Tools
In-Circuit Emulator
Design Browser
A low cost, high functionality ICE (In-Circuit Emulator) is avail-
able for development support. This hardware has the capability
to program single devices.
The Design Browser allows users to select and import precon-
figured designs into the user’s project. Users can easily browse
a catalog of preconfigured designs to facilitate time-to-design.
Examples provided in the tools include a 300-baud modem, LIN
Bus master and slave, fan controller, and magnetic card reader.
The emulator consists of a base unit that connects to the PC by
way of a USB port. The base unit is universal and will operate
with all PSoC devices. Emulation pods for each device family
are available separately. The emulation pod takes the place of
the PSoC device in the target board and performs full speed (24
MHz) operation.
Application Editor
In the Application Editor you can edit your C language and
Assembly language source code. You can also assemble, com-
pile, link, and build.
Assembler. The macro assembler allows the assembly code
to be merged seamlessly with C code. The link libraries auto-
matically use absolute addressing or can be compiled in relative
mode, and linked with other software modules to get absolute
addressing.
C Language Compiler. A C language compiler is available
that supports the PSoC family of devices. Even if you have
never worked in the C language before, the product quickly
allows you to create complete C programs for the PSoC family
devices.
The embedded, optimizing C compiler provides all the features
of C tailored to the PSoC architecture. It comes complete with
embedded libraries providing port and bus operations, standard
keypad and display support, and extended math functionality.
January 12, 2007
Document No. 38-12025 Rev. *K
5
[+] Feedback
CY8C21x34 Final Data Sheet
PSoC® Overview
User Module and Source Code Development Flows
Designing with User Modules
The development process for the PSoC device differs from that
of a traditional fixed function microprocessor. The configurable
analog and digital hardware blocks give the PSoC architecture
a unique flexibility that pays dividends in managing specification
change during development and by lowering inventory costs.
These configurable resources, called PSoC Blocks, have the
ability to implement a wide variety of user-selectable functions.
Each block has several registers that determine its function and
connectivity to other blocks, multiplexers, buses and to the IO
pins. Iterative development cycles permit you to adapt the hard-
ware as well as the software. This substantially lowers the risk
of having to select a different part to meet the final design
requirements.
Device Editor
Placement
User
Module
Selection
Source
Code
Generator
and
Parameter
-ization
Generate
Application
Application Editor
Source
Code
Editor
Project
Manager
Build
Manager
To speed the development process, the PSoC Designer Inte-
grated Development Environment (IDE) provides a library of
pre-built, pre-tested hardware peripheral functions, called “User
Modules.” User modules make selecting and implementing
peripheral devices simple, and come in analog, digital, and
mixed signal varieties. The standard User Module library con-
tains over 50 common peripherals such as ADCs, DACs Tim-
ers, Counters, UARTs, and other not-so common peripherals
such as DTMF Generators and Bi-Quad analog filter sections.
Build
All
Debugger
Each user module establishes the basic register settings that
implement the selected function. It also provides parameters
that allow you to tailor its precise configuration to your particular
application. For example, a Pulse Width Modulator User Mod-
ule configures one or more digital PSoC blocks, one for each 8
bits of resolution. The user module parameters permit you to
establish the pulse width and duty cycle. User modules also
provide tested software to cut your development time. The user
module application programming interface (API) provides high-
level functions to control and respond to hardware events at run
time. The API also provides optional interrupt service routines
that you can adapt as needed.
Event &
Breakpoint
Manager
Interface
to ICE
Storage
Inspector
The next step is to write your main program, and any sub-rou-
tines using PSoC Designer’s Application Editor subsystem.
The Application Editor includes a Project Manager that allows
you to open the project source code files (including all gener-
ated code files) from a hierarchal view. The source code editor
provides syntax coloring and advanced edit features for both C
and assembly language. File search capabilities include simple
string searches and recursive “grep-style” patterns. A single
mouse click invokes the Build Manager. It employs a profes-
sional-strength “makefile” system to automatically analyze all
file dependencies and run the compiler and assembler as nec-
essary. Project-level options control optimization strategies
used by the compiler and linker. Syntax errors are displayed in
a console window. Double clicking the error message takes you
directly to the offending line of source code. When all is correct,
the linker builds a HEX file image suitable for programming.
The API functions are documented in user module data sheets
that are viewed directly in the PSoC Designer IDE. These data
sheets explain the internal operation of the user module and
provide performance specifications. Each data sheet describes
the use of each user module parameter and documents the set-
ting of each register controlled by the user module.
The development process starts when you open a new project
and bring up the Device Editor, a graphical user interface (GUI)
for configuring the hardware. You pick the user modules you
need for your project and map them onto the PSoC blocks with
point-and-click simplicity. Next, you build signal chains by inter-
connecting user modules to each other and the IO pins. At this
stage, you also configure the clock source connections and
enter parameter values directly or by selecting values from
drop-down menus. When you are ready to test the hardware
configuration or move on to developing code for the project, you
perform the “Generate Application” step. This causes PSoC
Designer to generate source code that automatically configures
the device to your specification and provides the high-level user
module API functions.
The last step in the development process takes place inside the
PSoC Designer’s Debugger subsystem. The Debugger down-
loads the HEX image to the In-Circuit Emulator (ICE) where it
runs at full speed. Debugger capabilities rival those of systems
costing many times more. In addition to traditional single-step,
run-to-breakpoint and watch-variable features, the Debugger
provides a large trace buffer and allows you define complex
breakpoint events that include monitoring address and data bus
values, memory locations and external signals.
January 12, 2007
Document No. 38-12025 Rev. *K
6
[+] Feedback
CY8C21x34 Final Data Sheet
PSoC® Overview
Document Conventions
Table of Contents
For an in depth discussion and more information on your PSoC
device, obtain the PSoC Mixed-Signal Array Technical Refer-
ence Manual on http://www.cypress.com. This document is
organized into the following chapters and sections.
Acronyms Used
The following table lists the acronyms that are used in this doc-
ument.
1.
Pin Information ........................................................................................ 8
1.1 Pinouts ........................................................................................... 8
Acronym
AC
Description
alternating current
1.1.1
1.1.2
1.1.3
1.1.4
1.1.5
16-Pin Part Pinout .......................................................... 8
20-Pin Part Pinout .......................................................... 9
28-Pin Part Pinout ........................................................ 10
32-Pin Part Pinout ........................................................ 11
56-Pin Part Pinout ......................................................... 12
ADC
API
analog-to-digital converter
application programming interface
central processing unit
continuous time
CPU
CT
2.
3.
Register Reference ................................................................................ 14
2.1
2.2
Register Conventions ................................................................... 14
Register Mapping Tables ............................................................. 14
DAC
DC
digital-to-analog converter
direct current
Electrical Specifications ....................................................................... 17
ECO
EEPROM
FSR
GPIO
GUI
external crystal oscillator
electrically erasable programmable read-only memory
full scale range
3.1
3.2
3.3
Absolute Maximum Ratings ......................................................... 18
Operating Temperature ................................................................ 18
DC Electrical Characteristics ........................................................ 18
3.3.1
3.3.2
3.3.3
3.3.4
3.3.5
3.3.6
3.3.7
3.3.8
DC Chip-Level Specifications ........................................ 18
DC General Purpose IO Specifications ......................... 19
DC Operational Amplifier Specifications ....................... 20
DC Low Power Comparator Specifications ................... 20
DC Switch Mode Pump Specifications .......................... 21
DC Analog Mux Bus Specifications ............................... 22
DC POR and LVD Specifications .................................. 22
DC Programming Specifications ................................... 23
general purpose IO
graphical user interface
human body model
HBM
ICE
in-circuit emulator
ILO
internal low speed oscillator
internal main oscillator
input/output
3.4
AC Electrical Characteristics ........................................................ 24
IMO
3.4.1
3.4.2
3.4.3
3.4.4
3.4.5
3.4.6
3.4.7
3.4.8
3.4.9
AC Chip-Level Specifications ........................................ 24
AC General Purpose IO Specifications ......................... 26
AC Operational Amplifier Specifications ........................ 27
AC Low Power Comparator Specifications ................... 27
AC Analog Mux Bus Specifications ............................... 27
AC Digital Block Specifications ..................................... 27
AC External Clock Specifications .................................. 29
AC Programming Specifications .................................... 30
AC I2C Specifications .................................................... 31
IO
IPOR
LSb
imprecise power on reset
least-significant bit
LVD
low voltage detect
MSb
PC
most-significant bit
program counter
4.
5.
Packaging Information .......................................................................... 32
PLL
phase-locked loop
4.1
4.2
4.3
Packaging Dimensions ................................................................. 32
Thermal Impedances .................................................................. 36
Solder Reflow Peak Temperature ................................................ 36
POR
PPOR
PSoC®
PWM
SC
power on reset
precision power on reset
Programmable System-on-Chip™
pulse width modulator
switched capacitor
Development Tool Selection ................................................................ 37
5.1
Software ....................................................................................... 37
5.1.1
5.1.2
5.1.3
5.1.4
PSoC Designer............................................................... 37
PSoC Express‰ ........................................................... 37
PSoC Programmer ........................................................ 37
CY3202-C iMAGEcraft C Compiler ............................... 37
SLIMO
SMP
SRAM
slow IMO
5.2
5.3
Development Kits ......................................................................... 37
switch mode pump
5.2.1
5.2.2
CY3215-DK Basic Development Kit .............................. 37
CY3210-ExpressDK Development Kit ........................... 38
static random access memory
Evaluation Tools ........................................................................... 38
5.3.1
5.3.2
5.3.3
CY3210-MiniProg1 ........................................................ 38
CY3210-PSoCEval1 ...................................................... 38
CY3214-PSoCEvalUSB ................................................ 38
5.4
Device Programmers ................................................................... 38
Units of Measure
5.4.1
5.4.2
CY3216 Modular Programmer ...................................... 38
CY3207ISSP In-System Programmer ........................... 38
A units of measure table is located in the Electrical Specifica-
tions section. Table 3-1 on page 17 lists all the abbreviations
used to measure the PSoC devices.
5.5
5.6
5.7
Accessories (Emulation and Programming) ................................. 39
3rd-Party Tools ............................................................................. 39
Build a PSoC Emulator into Your Board ...................................... 39
6.
7.
Ordering Information ............................................................................ 40
6.1 Ordering Code Definitions ............................................................ 40
Numeric Naming
Sales and Service Information ............................................................. 41
7.1
7.2
Revision History ........................................................................... 41
Copyrights and Code Protection .................................................. 42
Hexidecimal numbers are represented with all letters in upper-
case with an appended lowercase ‘h’ (for example, ‘14h’ or
‘3Ah’). Hexidecimal numbers may also be represented by a ‘0x’
prefix, the C coding convention. Binary numbers have an
appended lowercase ‘b’ (e.g., 01010100b’ or ‘01000011b’).
Numbers not indicated by an ‘h’, ‘b’, or 0x are decimal.
January 12, 2007
Document No. 38-12025 Rev. *K
7
[+] Feedback
1. Pin Information
This chapter describes, lists, and illustrates the CY8C21x34 PSoC device pins and pinout configurations.
1.1
Pinouts
The CY8C21x34 PSoC device is available in a variety of packages which are listed and illustrated in the following tables. Every port
pin (labeled with a “P”) is capable of Digital IO and connection to the common analog bus. However, Vss, Vdd, SMP, and XRES are
not capable of Digital IO.
1.1.1
16-Pin Part Pinout
Table 1-1. 16-Pin Part Pinout (SOIC)
Type
Pin
CY8C21234 16-Pin PSoC Device
Name
Description
No.
Digital Analog
1
2
3
IO
IO
IO
I, M
I, M
I, M
P0[7] Analog column mux input.
P0[5] Analog column mux input.
A, I,M, P0[7]
A, I,M, P0[5]
A, I,M, P0[3]
A, I,M, P0[1]
SMP
Vdd
1
2
3
4
5
6
7
8
16
15
14
13
12
11
10
9
P0[6], A,I, M
P0[4], A,I, M
P0[2], A,I, M
P0[0], A,I, M
P1[4],EXTCLK,M
P1[2],M
P0[3] Analog column mux input, integrating
input.
SOIC
4
5
IO
I, M
P0[1] Analog column mux input, integrating
input.
Vss
M,I2CSCL,P1[1]
Vss
Power
Power
SMP
Switch Mode Pump (SMP) connection to
required external components.
P1[0],I2CSDA,M
6
Vss
Ground connection.
7
IO
M
P1[1] I2C Serial Clock (SCL), ISSP-SCLK*.
Vss Ground connection.
8
Power
9
IO
IO
IO
IO
IO
IO
IO
M
M
P1[0] I2C Serial Data (SDA), ISSP-SDATA*.
P1[2]
10
11
12
13
14
15
16
M
P1[4] Optional External Clock Input (EXTCLK).
P0[0] Analog column mux input.
P0[2] Analog column mux input.
P0[4] Analog column mux input.
P0[6] Analog column mux input.
I, M
I, M
I, M
I, M
Power
Vdd
Supply voltage.
LEGEND A = Analog, I = Input, O = Output, and M = Analog Mux Input.
* These are the ISSP pins, which are not High Z at POR (Power On Reset).
See the PSoC Mixed-Signal Array Technical Reference Manual for details.
January 12, 2007
Document No. 38-12025 Rev. *K
8
[+] Feedback
CY8C21x34 Final Data Sheet
1. Pin Information
1.1.2
20-Pin Part Pinout
Table 1-2. 20-Pin Part Pinout (SSOP)
Type
Pin
CY8C21334 20-Pin PSoC Device
Name
Description
No.
Digital Analog
1
2
3
IO
IO
IO
I, M
I, M
I, M
P0[7]
P0[5]
P0[3]
Analog column mux input.
Analog column mux input.
A, I,M, P0[7]
A, I,M, P0[5]
A, I,M, P0[3]
A, I,M, P0[1]
Vss
Vdd
20
19
18
17
16
15
14
13
12
11
1
2
3
4
5
6
7
8
9
P0[6], A,I, M
P0[4], A,I, M
P0[2], A,I, M
P0[0], A,I, M
XRES
P1[6],M
P1[4],EXTCLK,M
P1[2],M
Analog column mux input, integrating
input.
4
IO
I, M
P0[1]
Analog column mux input, integrating
input.
SSOP
M,I2C SCL,P1[7]
M,I2C SDA,P1[5]
M,P1[3]
5
6
Power
Vss
Ground connection.
IO
IO
IO
IO
M
M
M
M
P1[7]
P1[5]
P1[3]
P1[1]
Vss
I2C Serial Clock (SCL).
I2C Serial Data (SDA).
M,I2C
SCL,P1[1]
Vss
7
P1[0],I2C SDA,M
10
8
9
I2C Serial Clock (SCL), ISSP-SCLK*.
Ground connection.
10
11
12
13
Power
IO
IO
IO
M
M
M
P1[0]
P1[2]
P1[4]
I2C Serial Data (SDA), ISSP-SDATA*.
Optional External Clock Input (EXT-
CLK).
14
15
IO
M
P1[6]
Input
XRES
Active high external reset with internal
pull down.
16
17
18
19
20
IO
IO
IO
IO
I, M
I, M
I, M
I, M
P0[0]
P0[2]
P0[4]
P0[6]
Vdd
Analog column mux input.
Analog column mux input.
Analog column mux input.
Analog column mux input.
Supply voltage.
Power
LEGEND A = Analog, I = Input, O = Output, and M = Analog Mux Input.
* These are the ISSP pins, which are not High Z at POR (Power On Reset).
See the PSoC Mixed-Signal Array Technical Reference Manual for details.
January 12, 2007
Document No. 38-12025 Rev. *K
9
[+] Feedback
CY8C21x34 Final Data Sheet
1. Pin Information
1.1.3
28-Pin Part Pinout
Table 1-3. 28-Pin Part Pinout (SSOP)
Type
Pin
CY8C21534 28-Pin PSoC Device
Name
Description
No.
Digital Analog
1
2
IO
IO
I, M
I, M
P0[7]
P0[5]
Analog column mux input.
A, I,M, P0[7]
A, I,M, P0[5]
A, I,M, P0[3]
A, I,M, P0[1]
M,P2[7]
1
2
3
4
5
6
7
8
9
10
11
12
13
14
Vdd
28
27
26
25
24
23
22
21
20
19
18
17
16
15
Analog column mux input and column
output.
P0[6], A,I, M
P0[4], A,I, M
P0[2], A,I, M
P0[0], A,I, M
P2[6],M
3
4
IO
IO
I, M
I, M
P0[3]
P0[1]
Analog column mux input and column
output, integrating input.
Analog column mux input, integrating
input.
M,P2[5]
M, P2[3]
M, P2[1]
P2[4],M
P2[2],M
SSOP
5
IO
IO
IO
IO
M
M
P2[7]
P2[5]
P2[3]
P2[1]
Vss
6
Vss
P2[0],M
XRES
P1[6],M
7
I, M
I, M
Direct switched capacitor block input.
Direct switched capacitor block input.
Ground connection.
M,I2C SCL,P1[7]
M,I2C SDA,P1[5]
M,P1[3]
8
P1[4],EXTCLK,M
P1[2],M
P1[0],I2C SDA,M
9
Power
Power
M,I2C SCL,P1[1]
Vss
10
11
12
13
14
15
16
17
IO
IO
IO
IO
M
M
M
M
P1[7]
P1[5]
P1[3]
P1[1]
Vss
I2C Serial Clock (SCL).
I2C Serial Data (SDA).
I2C Serial Clock (SCL), ISSP-SCLK*.
Ground connection.
IO
IO
IO
M
M
M
P1[0]
P1[2]
P1[4]
I2C Serial Data (SDA), ISSP-SDATA*.
Optional External Clock Input (EXT-
CLK).
18
19
IO
M
P1[6]
Input
XRES
Active high external reset with internal
pull down.
20
21
22
23
24
25
26
27
28
IO
IO
IO
IO
IO
IO
IO
IO
I, M
I, M
M
P2[0]
P2[2]
P2[4]
P2[6]
P0[0]
P0[2]
P0[4]
P0[6]
Vdd
Direct switched capacitor block input.
Direct switched capacitor block input.
M
I, M
I, M
I, M
I, M
Analog column mux input.
Analog column mux input.
Analog column mux input
Analog column mux input.
Supply voltage.
Power
LEGEND A: Analog, I: Input, O = Output, and M = Analog Mux Input.
* These are the ISSP pins, which are not High Z at POR (Power On Reset).
See the PSoC Mixed-Signal Array Technical Reference Manual for details.
January 12, 2007
Document No. 38-12025 Rev. *K
10
[+] Feedback
CY8C21x34 Final Data Sheet
1. Pin Information
1.1.4
32-Pin Part Pinout
Table 1-4. 32-Pin Part Pinout (QFN**)
Type
Pin
CY8C21434 32-Pin PSoC Device
Name
Description
No.
Digital Analog
1
IO
I, M
P0[1]
Analog column mux input, integrating
input.
2
3
4
5
6
6
IO
IO
IO
IO
IO
M
M
M
M
M
P2[7]
P2[5]
P2[3]
P2[1]
P3[3]
SMP
In CY8C21434 part.
Power
Switch Mode Pump (SMP) connection to
required external components in
CY8C21634 part.
7
IO
M
P3[1]
Vss
In CY8C21434 part.
7
Power
Power
Ground connection in CY8C21634 part.
I2C Serial Clock (SCL).
8
IO
IO
IO
IO
M
M
M
M
P1[7]
P1[5]
P1[3]
P1[1]
Vss
9
I2C Serial Data (SDA).
10
11
12
13
14
15
16
I2C Serial Clock (SCL), ISSP-SCLK*.
Ground connection.
IO
IO
IO
IO
M
M
M
M
P1[0]
P1[2]
P1[4]
P1[6]
I2C Serial Data (SDA), ISSP-SDATA*.
Optional External Clock Input (EXTCLK).
17
Input
XRES
Active high external reset with internal
pull down.
CY8C21634 32-Pin PSoC Device
18
19
20
21
22
23
24
25
26
27
28
29
30
31
IO
IO
IO
IO
IO
IO
IO
IO
IO
IO
M
M
M
M
M
M
P3[0]
P3[2]
P2[0]
P2[2]
P2[4]
P2[6]
P0[0]
P0[2]
P0[4]
P0[6]
Vdd
I, M
I, M
I, M
I, M
Analog column mux input.
Analog column mux input.
Analog column mux input.
Analog column mux input.
Supply voltage.
Power
IO
IO
IO
I, M
I, M
I, M
P0[7]
P0[5]
P0[3]
Analog column mux input.
Analog column mux input.
Analog column mux input, integrating
input.
32
Power
Vss
Ground connection.
LEGEND A = Analog, I = Input, O = Output, and M = Analog Mux Input.
* These are the ISSP pins, which are not High Z at POR (Power On Reset).
See the PSoC Mixed-Signal Array Technical Reference Manual for details.
** The center pad on the QFN package should be connected to ground (Vss)
for best mechanical, thermal, and electrical performance. If not connected to
ground, it should be electrically floated and not connected to any other signal.
January 12, 2007
Document No. 38-12025 Rev. *K
11
[+] Feedback
CY8C21x34 Final Data Sheet
1. Pin Information
1.1.5
56-Pin Part Pinout
The 56-pin SSOP part is for the CY8C21001 On-Chip Debug (OCD) PSoC device.
Note This part is only used for in-circuit debugging. It is NOT available for production.
Table 1-5. 56-Pin Part Pinout (SSOP)
Type
CY8C21001 56-Pin PSoC Device
Pin
No.
Pin
Name
Description
Digital Analog
1
Power
Vss
Ground connection.
Vss
56
55
Vdd
1
2
2
IO
IO
IO
IO
IO
IO
IO
IO
I
I
I
I
P0[7]
P0[5]
P0[3]
P0[1]
P2[7]
P2[5]
P2[3]
P2[1]
NC
Analog column mux input.
AI, P0[7]
AI, P0[5]
AI, P0[3]
P0[6], AI
P0[4], AI
P0[2], AI
3
4
5
6
54
53
3
Analog column mux input and column output.
Analog column mux input and column output.
Analog column mux input.
4
AI, P0[1]
P2[7]
P2[5]
P2[3]
P2[1]
NC
P0[0], AI
P2[6]
52
51
5
P2[4]
P2[2]
P2[0]
NC
7
8
9
50
49
48
6
7
10
47
46
45
44
43
42
41
40
39
38
37
36
35
34
8
I
I
Direct switched capacitor block input.
Direct switched capacitor block input.
No connection.
NC
NC
NC
NC
11
12
13
9
P3[2]
P3[0]
CCLK
HCLK
XRES
NC
10
11
12
13
14
15
16
OCDE
OCDO
SMP
14
SSOP
NC
No connection..
15
16
NC
No connection.
17
Vss
Vss
NC
No connection..
NC
NC
NC
18
19
20
P3[3]
P3[1]
NC
OCD
OCD
OCDE
OCD even data IO.
OCDO OCD odd data output.
NC
21
22
23
NC
Power
SMP
Switch Mode Pump (SMP) connection to
required external components.
NC
P1[6]
I2C SCL, P1[7]
P1[4], EXTCLK
P1[2]
I2C SDA, P1[5]
NC
24
25
33
32
17
18
19
20
Power
Power
Vss
Ground connection.
Vss
Ground connection.
P1[3]
SCLK, I2C SCL, P1[1]
Vss
P1[0], I2C
NC
SDA, SDATA
26
27
28
31
30
IO
IO
P3[3]
P3[1]
NC
29
21
NC
No connection.
Not for Production
22
23
24
25
26
NC
No connection..
IO
IO
P1[7]
P1[5]
NC
I2C Serial Clock (SCL).
I2C Serial Data (SDA).
No connection.
IO
IO
P1[3]
I
.
FMTEST
27
P1[1]
Crystal Input (XTALin), I2C Serial Clock
(SCL), ISSP-SCLK*.
28
29
30
31
Power
Vss
NC
Ground connection.
No connection.
NC
No connection..
IO
IO
P1[0]
Crystal Output (XTALout), I2C Serial Data
(SDA), ISSP-SDATA*.
32
P1[2]
V
.
FMTEST
33
34
35
36
37
38
39
40
41
IO
IO
P1[4]
P1[6]
NC
Optional External Clock Input (EXTCLK).
No connection..
No connection.
No connection..
No connection.
No connection..
No connection..
NC
NC
NC
NC
NC
Input
XRES
Active high external reset with internal pull
down.
42
43
44
45
46
47
OCD
OCD
IO
HCLK
CCLK
P3[0]
P3[2]
NC
OCD high-speed clock output.
OCD CPU clock output.
IO
No connection.
No connection..
NC
January 12, 2007
Document No. 38-12025 Rev. *K
12
[+] Feedback
CY8C21x34 Final Data Sheet
1. Pin Information
Table 1-5. 56-Pin Part Pinout (SSOP)
48
49
50
51
52
53
54
55
56
IO
IO
IO
IO
IO
IO
IO
IO
I
I
P2[0]
P2[2]
P2[4]
P2[6]
P0[0]
P0[2]
P0[4]
P0[6]
Vdd
I
I
I
I
Analog column mux input.
Analog column mux input and column output.
Analog column mux input and column output.
Analog column mux input.
Power
Supply voltage.
LEGEND: A = Analog, I = Input, O = Output, and OCD = On-Chip Debug.
* These are the ISSP pins, which are not High Z at POR (Power On Reset). See the PSoC Mixed-Signal Array Technical Reference Manual for details.
January 12, 2007
Document No. 38-12025 Rev. *K
13
[+] Feedback
2. Register Reference
This chapter lists the registers of the CY8C21x34 PSoC device. For detailed register information, reference the
PSoC Mixed-Signal Array Technical Reference Manual.
2.1
Register Conventions
2.2
Register Mapping Tables
The register conventions specific to this section are listed in the
following table.
The PSoC device has a total register address space of 512
bytes. The register space is referred to as IO space and is
divided into two banks. The XOI bit in the Flag register (CPU_F)
determines which bank the user is currently in. When the XOI
bit is set the user is in Bank 1.
Convention
Description
Read register or bit(s)
R
W
L
Write register or bit(s)
Logical register or bit(s)
Clearable register or bit(s)
Access is bit specific
Note In the following register mapping tables, blank fields are
Reserved and should not be accessed.
C
#
January 12, 2007
Document No. 38-12025 Rev. *K
14
[+] Feedback
CY8C21x34 Final Data Sheet
2. Register Reference
Register Map 0 Table: User Space
PRT0DR
PRT0IE
PRT0GS
PRT0DM2
PRT1DR
PRT1IE
PRT1GS
PRT1DM2
PRT2DR
PRT2IE
PRT2GS
PRT2DM2
PRT3DR
PRT3IE
00
01
02
03
04
05
06
07
08
09
0A
0B
0C
0D
0E
0F
10
11
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
40
41
42
43
44
45
46
47
48
49
4A
4B
4C
4D
4E
4F
50
51
52
53
54
55
56
57
58
59
5A
5B
5C
5D
5E
5F
60
61
62
63
64
65
66
67
68
69
6A
6B
6C
6D
6E
6F
70
71
72
73
74
75
76
77
78
79
7A
7B
7C
7D
7E
7F
ASE10CR0
ASE11CR0
80
81
82
83
84
85
86
87
88
89
8A
8B
8C
8D
8E
8F
90
91
92
93
94
95
96
97
98
99
9A
9B
9C
9D
9E
9F
A0
A1
A2
A3
A4
A5
A6
A7
A8
A9
AA
AB
AC
AD
AE
AF
B0
B1
B2
B3
B4
B5
B6
B7
B8
B9
BA
BB
BC
BD
BE
BF
RW
RW
C0
C1
C2
C3
C4
C5
C6
C7
C8
C9
CA
CB
CC
CD
CE
CF
D0
D1
D2
D3
D4
D5
D6
D7
D8
D9
DA
DB
DC
DD
DE
DF
E0
E1
E2
E3
E4
E5
E6
E7
E8
E9
EA
EB
EC
ED
EE
EF
F0
F1
F2
F3
F4
F5
F6
F7
F8
F9
FA
FB
FC
FD
FE
FF
PRT3GS
PRT3DM2
CUR_PP
STK_PP
RW
RW
12
13
14
15
16
17
18
19
1A
1B
1C
1D
1E
1F
20
21
22
23
24
25
26
27
28
29
2A
2B
2C
2D
2E
2F
30
31
32
33
34
35
36
37
38
39
3A
3B
3C
3D
3E
3F
IDX_PP
RW
RW
RW
RW
#
RW
#
RW
RW
MVR_PP
MVW_PP
I2C_CFG
I2C_SCR
I2C_DR
I2C_MSCR
INT_CLR0
INT_CLR1
INT_CLR3
INT_MSK3
RW
RW
DBB00DR0
DBB00DR1
DBB00DR2
DBB00CR0
DBB01DR0
DBB01DR1
DBB01DR2
DBB01CR0
DCB02DR0
DCB02DR1
DCB02DR2
DCB02CR0
DCB03DR0
DCB03DR1
DCB03DR2
DCB03CR0
#
AMX_IN
AMUXCFG
PWM_CR
RW
RW
RW
INT_MSK0
INT_MSK1
INT_VC
RW
RW
RC
W
W
RW
#
RES_WDT
#
CMP_CR0
CMP_CR1
#
W
RW
#
RW
DEC_CR0
DEC_CR1
RW
RW
#
#
#
ADC0_CR
ADC1_CR
W
RW
#
#
TMP_DR0
TMP_DR1
TMP_DR2
TMP_DR3
RW
RW
RW
RW
W
RW
#
RDI0RI
RDI0SYN
RDI0IS
RDI0LT0
RDI0LT1
RDI0RO0
RDI0RO1
RW
RW
RW
RW
RW
RW
RW
ACE00CR1
ACE00CR2
RW
RW
ACE01CR1
ACE01CR2
RW
RW
CPU_F
RL
DAC_D
CPU_SCR1
CPU_SCR0
RW
#
#
Blank fields are Reserved and should not be accessed.
# Access is bit specific.
January 12, 2007
Document No. 38-12025 Rev. *K
15
[+] Feedback
CY8C21x34 Final Data Sheet
2. Register Reference
Register Map 1 Table: Configuration Space
PRT0DM0
PRT0DM1
PRT0IC0
PRT0IC1
PRT1DM0
PRT1DM1
PRT1IC0
PRT1IC1
PRT2DM0
PRT2DM1
PRT2IC0
PRT2IC1
PRT3DM0
PRT3DM1
PRT3IC0
PRT3IC1
00
01
02
03
04
05
06
07
08
09
0A
0B
0C
0D
0E
0F
10
11
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
40
41
42
43
44
45
46
47
48
49
4A
4B
4C
4D
4E
4F
50
51
52
53
54
55
56
57
58
59
5A
5B
5C
5D
5E
5F
60
61
62
63
ASE10CR0
ASE11CR0
80
81
82
83
84
85
86
87
88
89
8A
8B
8C
8D
8E
8F
90
91
92
93
94
95
96
97
98
99
9A
9B
9C
9D
9E
9F
A0
A1
A2
A3
A4
A5
A6
A7
A8
A9
AA
AB
AC
AD
AE
AF
B0
B1
B2
B3
B4
B5
B6
B7
B8
B9
BA
BB
BC
BD
BE
BF
RW
RW
C0
C1
C2
C3
C4
C5
C6
C7
C8
C9
CA
CB
CC
CD
CE
CF
D0
D1
D2
D3
D4
D5
D6
D7
D8
D9
DA
DB
DC
GDI_O_IN
GDI_E_IN
GDI_O_OU
GDI_E_OU
RW
RW
RW
RW
12
13
14
15
16
17
18
19
1A
1B
1C
1D
1E
1F
20
21
22
23
24
25
26
27
28
29
2A
2B
2C
2D
2E
2F
30
31
32
33
34
35
36
37
38
39
3A
3B
3C
3D
3E
3F
MUX_CR0
MUX_CR1
MUX_CR2
MUX_CR3
RW
RW
RW
RW
OSC_GO_EN DD
RW
RW
RW
RW
RW
RW
RW
R
OSC_CR4
OSC_CR3
OSC_CR0
OSC_CR1
OSC_CR2
VLT_CR
VLT_CMP
ADC0_TR
ADC1_TR
DE
DF
E0
E1
E2
E3
E4
E5
E6
E7
E8
E9
EA
EB
EC
ED
EE
EF
F0
F1
F2
F3
F4
F5
F6
F7
F8
F9
FA
FB
FC
FD
FE
FF
DBB00FN
DBB00IN
DBB00OU
RW
RW
RW
CLK_CR0
CLK_CR1
ABF_CR0
AMD_CR0
RW
RW
RW
RW
RW
DBB01FN
DBB01IN
DBB01OU
RW
RW
RW
CMP_GO_EN 64
65
RW
RW
AMD_CR1
ALT_CR0
66
67
68
69
6A
6B
6C
6D
6E
6F
70
71
72
73
74
75
76
77
78
79
7A
7B
7C
7D
7E
7F
RW
RW
DCB02FN
DCB02IN
DCB02OU
RW
RW
RW
IMO_TR
ILO_TR
BDG_TR
ECO_TR
W
W
RW
W
CLK_CR3
TMP_DR0
TMP_DR1
TMP_DR2
TMP_DR3
RW
RW
RW
RW
RW
DCB03FN
DCB03IN
DCB03OU
RW
RW
RW
RDI0RI
RDI0SYN
RDI0IS
RDI0LT0
RDI0LT1
RDI0RO0
RDI0RO1
RW
RW
RW
RW
RW
RW
RW
ACE00CR1
ACE00CR2
RW
RW
ACE01CR1
ACE01CR2
RW
RW
CPU_F
RL
FLS_PR1
RW
DAC_CR
CPU_SCR1
CPU_SCR0
RW
#
#
Blank fields are Reserved and should not be accessed.
# Access is bit specific.
January 12, 2007
Document No. 38-12025 Rev. *K
16
[+] Feedback
3. Electrical Specifications
This chapter presents the DC and AC electrical specifications of the CY8C21x34 PSoC device. For the most up to date electrical
specifications, confirm that you have the most recent data sheet by going to the web at http://www.cypress.com/psoc.
Specifications are valid for -40oC ≤ T ≤ 85oC and T ≤ 100oC as specified, except where noted.
A
J
Refer to Table 3-15 for the electrical specifications on the internal main oscillator (IMO) using SLIMO mode.
Figure 3-1a. Voltage versus CPU Frequency
Figure 3-1b. IMO Frequency Trim Options
5.25
5.25
SLIMO
SLIMO
Mode=1
Mode=0
4.75
4.75
3.60
3.00
2.40
SLIMO
Mode=1
SLIMO
Mode=0
3.00
2.40
SLIMO SLIMO
Mode=1 Mode=1
93 kHz
12 MHz
CPUFrequency
24 MHz
3 MHz
93 kHz
6 MHz
12 MHz
24 MHz
IMOFrequency
The following table lists the units of measure that are used in this chapter.
Table 3-1: Units of Measure
Symbol
Unit of Measure
Symbol
µW
mA
ms
mV
nA
Unit of Measure
o
C
degree Celsius
decibels
microwatts
dB
fF
milli-ampere
milli-second
milli-volts
femto farad
hertz
Hz
KB
1024 bytes
1024 bits
nanoampere
nanosecond
nanovolts
Kbit
kHz
kΩ
ns
kilohertz
nV
kilohm
Ω
ohm
MHz
MΩ
µA
megahertz
megaohm
microampere
microfarad
microhenry
microsecond
microvolts
pA
picoampere
picofarad
pF
pp
peak-to-peak
parts per million
picosecond
µF
ppm
ps
µH
µs
sps
σ
samples per second
sigma: one standard deviation
volts
µV
µVrms
microvolts root-mean-square
V
January 12, 2007
Document No. 38-12025 Rev. *K
17
[+] Feedback
CY8C21x34 Final Data Sheet
3. Electrical Specifications
3.1
Absolute Maximum Ratings
Table 3-2. Absolute Maximum Ratings
Symbol
Description
Min
-55
Typ
Max
+100
Units
Notes
o
o
T
Storage Temperature
25
Higher storage temperatures will reduce data
retention time. Recommended storage temper-
C
STG
o
o
ature is +25 C ± 25 C. Extended duration stor-
o
age temperatures above 65 C will degrade
reliability.
T
A
Ambient Temperature with Power Applied
Supply Voltage on Vdd Relative to Vss
DC Input Voltage
-40
–
–
–
–
–
–
–
+85
C
Vdd
-0.5
+6.0
V
V
V
Vss - 0.5
Vss - 0.5
-25
Vdd + 0.5
Vdd + 0.5
+50
V
IO
DC Voltage Applied to Tri-state
Maximum Current into any Port Pin
Electro Static Discharge Voltage
Latch-up Current
V
IOZ
MIO
I
mA
V
ESD
LU
2000
–
–
Human Body Model ESD.
200
mA
3.2
Operating Temperature
Table 3-3. Operating Temperature
Symbol
Description
Min
-40
Typ
Max
+85
Units
Notes
o
o
T
A
Ambient Temperature
Junction Temperature
–
–
C
C
T
-40
+100
The temperature rise from ambient to junction is
package specific. See “Thermal Impedances”
on page 36. The user must limit the power con-
sumption to comply with this requirement.
J
3.3
DC Electrical Characteristics
3.3.1
DC Chip-Level Specifications
The following table lists guaranteed maximum and minimum specifications for the voltage and temperature ranges: 4.75V to 5.25V
and -40°C ≤ TA ≤ 85°C, 3.0V to 3.6V and -40°C ≤ TA ≤ 85°C, or 2.4V to 3.0V and -40°C ≤ TA ≤ 85°C, respectively. Typical parameters
apply to 5V, 3.3V, or 2.7V at 25°C and are for design guidance only.
Table 3-4. DC Chip-Level Specifications
Symbol
Description
Min
2.40
Typ
Max
5.25
Units
Notes
Vdd
Supply Voltage
–
3
V
See table titled “DC POR and LVD Specifica-
tions” on page 22.
o
I
Supply Current, IMO = 24 MHz
–
–
–
4
mA
mA
mA
Conditions are Vdd = 5.0V, T = 25 C, CPU = 3
A
MHz, 48 MHz disabled. VC1 = 1.5 MHz, VC2 =
93.75 kHz, VC3 = 0.366 kHz.
DD
o
I
Supply Current, IMO = 6 MHz using SLIMO mode.
Supply Current, IMO = 6 MHz using SLIMO mode.
1.2
1.1
2
Conditions are Vdd = 3.3V, T = 25 C, CPU = 3
A
MHz, clock doubler disabled. VC1 = 375 kHz,
VC2 = 23.4 kHz, VC3 = 0.091 kHz.
DD3
o
I
1.5
Conditions are Vdd = 2.55V, T = 25 C, CPU = 3
A
DD27
MHz, clock doubler disabled. VC1 = 375 kHz,
VC2 = 23.4 kHz, VC3 = 0.091 kHz.
o
o
I
Sleep (Mode) Current with POR, LVD, Sleep Timer, WDT,
and internal slow oscillator active. Mid temperature range.
–
2.6
4.
µA
µA
V
Vdd = 2.55V, 0 C ≤ T ≤ 40 C.
SB27
A
o
o
I
SB
Sleep (Mode) Current with POR, LVD, Sleep Timer, WDT,
and internal slow oscillator active.
–
2.8
5
Vdd = 3.3V, -40 C ≤ T ≤ 85 C.
A
V
Reference Voltage (Bandgap)
1.28
1.30
1.32
Trimmed for appropriate Vdd. Vdd = 3.0V to
5.25V.
REF
January 12, 2007
Document No. 38-12025 Rev. *K
18
[+] Feedback
CY8C21x34 Final Data Sheet
3. Electrical Specifications
Table 3-4. DC Chip-Level Specifications (continued)
Symbol
Description
Reference Voltage (Bandgap)
Min
1.16
Typ
1.30
Max
1.33
Units
Notes
V
REF27
V
V
Trimmed for appropriate Vdd. Vdd = 2.4V to
3.0V.
AGND
Analog Ground
V
V
V
REF
REF
REF
- 0.003
+ 0.003
3.3.2
DC General Purpose IO Specifications
The following tables list guaranteed maximum and minimum specifications for the voltage and temperature ranges: 4.75V to 5.25V
and -40°C ≤ TA ≤ 85°C, 3.0V to 3.6V and -40°C ≤ TA ≤ 85°C, or 2.4V to 3.0V and -40°C ≤ TA ≤ 85°C, respectively. Typical parameters
apply to 5V, 3.3V, and 2.7V at 25°C and are for design guidance only.
Table 3-5. 5V and 3.3V DC GPIO Specifications
Symbol
Description
Min
Typ
5.6
Max
Units
kΩ
Notes
R
Pull-up Resistor
4
4
8
8
–
PU
PD
OH
R
Pull-down Resistor
High Output Level
5.6
–
kΩ
V
Vdd - 1.0
V
IOH = 10 mA, Vdd = 4.75 to 5.25V (8 total loads,
4 on even port pins (for example, P0[2], P1[4]),
4 on odd port pins (for example, P0[3], P1[5])).
V
Low Output Level
–
–
0.75
0.8
V
IOL = 25 mA, Vdd = 4.75 to 5.25V (8 total loads,
4 on even port pins (for example, P0[2], P1[4]),
4 on odd port pins (for example, P0[3], P1[5])).
OL
V
V
V
I
Input Low Level
Input High Level
Input Hysteresis
–
–
V
Vdd = 3.0 to 5.25.
Vdd = 3.0 to 5.25.
IL
IH
H
2.1
–
–
V
60
1
–
mV
nA
pF
pF
Input Leakage (Absolute Value)
Capacitive Load on Pins as Input
Capacitive Load on Pins as Output
–
–
Gross tested to 1 µA.
IL
o
C
C
–
3.5
3.5
10
10
Package and pin dependent. Temp = 25 C.
IN
o
–
Package and pin dependent. Temp = 25 C.
OUT
Table 3-6. 2.7V DC GPIO Specifications
Symbol
Description
Min
Typ
Max
Units
Notes
R
Pull-up Resistor
4
5.6
5.6
–
8
8
–
kΩ
kΩ
V
PU
PD
OH
R
Pull-down Resistor
High Output Level
4
V
Vdd - 0.4
IOH = 2.5 mA (6.25 Typ), Vdd = 2.4 to 3.0V (16
mA maximum, 50 mA Typ combined IOH bud-
get).
V
OL
Low Output Level
–
–
0.75
V
IOL = 10 mA, Vdd = 2.4 to 3.0V (90 mA maxi-
mum combined IOL budget).
V
V
V
I
Input Low Level
Input High Level
Input Hysteresis
–
–
0.75
–
V
Vdd = 2.4 to 3.0.
Vdd = 2.4 to 3.0.
IL
IH
H
2.0
–
–
V
90
1
–
mV
nA
pF
pF
Input Leakage (Absolute Value)
Capacitive Load on Pins as Input
Capacitive Load on Pins as Output
–
–
Gross tested to 1 µA.
IL
o
C
C
–
3.5
3.5
10
10
Package and pin dependent. Temp = 25 C.
IN
o
–
Package and pin dependent. Temp = 25 C.
OUT
January 12, 2007
Document No. 38-12025 Rev. *K
19
[+] Feedback
CY8C21x34 Final Data Sheet
3. Electrical Specifications
3.3.3
DC Operational Amplifier Specifications
The following tables list guaranteed maximum and minimum specifications for the voltage and temperature ranges: 4.75V to 5.25V
and -40°C ≤ TA ≤ 85°C, 3.0V to 3.6V and -40°C ≤ TA ≤ 85°C, or 2.4V to 3.0V and -40°C ≤ TA ≤ 85°C, respectively. Typical parameters
apply to 5V, 3.3V, or 2.7V at 25°C and are for design guidance only.
Table 3-7. 5V DC Operational Amplifier Specifications
Symbol
Description
Input Offset Voltage (absolute value)
Average Input Offset Voltage Drift
Input Leakage Current (Port 0 Analog Pins)
Input Capacitance (Port 0 Analog Pins)
Common Mode Voltage Range
Min
Typ
2.5
Max
Units
mV
Notes
V
–
15
–
OSOA
o
TCV
–
10
200
4.5
–
µV/ C
OSOA
a
–
–
pA
pF
V
Gross tested to 1 µA.
Package and pin dependent. Temp = 25 C.
I
EBOA
o
C
–
9.5
INOA
V
0.0
Vdd - 1
CMOA
G
I
Open Loop Gain
–
–
80
10
–
dB
OLOA
Amplifier Supply Current
30
µA
SOA
a. Atypical behavior: IEBOA of Port 0 Pin 0 is below 1 nA at 25°C; 50 nA over temperature. Use Port 0 Pins 1-7 for the lowest leakage of 200 nA.
Table 3-8. 3.3V DC Operational Amplifier Specifications
Symbol
Description
Input Offset Voltage (absolute value)
Average Input Offset Voltage Drift
Input Leakage Current (Port 0 Analog Pins)
Input Capacitance (Port 0 Analog Pins)
Common Mode Voltage Range
Open Loop Gain
Min
Typ
2.5
Max
15
Units
mV
Notes
V
–
–
–
–
0
–
–
OSOA
o
TCV
10
200
4.5
–
–
µV/ C
OSOA
a
–
pA
pF
V
Gross tested to 1 µA.
Package and pin dependent. Temp = 25 C.
I
EBOA
o
C
9.5
INOA
V
Vdd - 1
–
CMOA
G
I
80
10
dB
µA
OLOA
Amplifier Supply Current
30
SOA
a. Atypical behavior: IEBOA of Port 0 Pin 0 is below 1 nA at 25°C; 50 nA over temperature. Use Port 0 Pins 1-7 for the lowest leakage of 200 nA.
Table 3-9. 2.7V DC Operational Amplifier Specifications
Symbol
Description
Input Offset Voltage (absolute value)
Average Input Offset Voltage Drift
Input Leakage Current (Port 0 Analog Pins)
Input Capacitance (Port 0 Analog Pins)
Common Mode Voltage Range
Open Loop Gain
Min
Typ
2.5
Max
15
Units
mV
Notes
V
–
–
–
–
0
–
–
OSOA
o
TCV
10
200
4.5
–
–
µV/ C
OSOA
a
–
pA
pF
V
Gross tested to 1 µA.
Package and pin dependent. Temp = 25 C.
I
EBOA
o
C
9.5
INOA
V
Vdd - 1
–
CMOA
G
I
80
10
dB
µA
OLOA
Amplifier Supply Current
30
SOA
a. Atypical behavior: IEBOA of Port 0 Pin 0 is below 1 nA at 25°C; 50 nA over temperature. Use Port 0 Pins 1-7 for the lowest leakage of 200 nA.
3.3.4
DC Low Power Comparator Specifications
The following table lists guaranteed maximum and minimum specifications for the voltage and temperature ranges: 4.75V to 5.25V
and -40°C ≤ TA ≤ 85°C, 3.0V to 3.6V and -40°C ≤ TA ≤ 85°C, or 2.4V to 3.0V and -40°C ≤ TA ≤ 85°C, respectively. Typical parameters
apply to 5V at 25°C and are for design guidance only.
Table 3-10. DC Low Power Comparator Specifications
Symbol
Description
Low power comparator (LPC) reference voltage range
LPC supply current
Min
Typ
Max
Vdd - 1
40
Units
Notes
V
I
0.2
–
–
V
REFLPC
10
µA
SLPC
V
LPC voltage offset
–
2.5
30
mV
OSLPC
January 12, 2007
Document No. 38-12025 Rev. *K
20
[+] Feedback
CY8C21x34 Final Data Sheet
3. Electrical Specifications
3.3.5
DC Switch Mode Pump Specifications
The following table lists guaranteed maximum and minimum specifications for the voltage and temperature ranges: 4.75V to 5.25V
and -40°C ≤ TA ≤ 85°C, 3.0V to 3.6V and -40°C ≤ TA ≤ 85°C, or 2.4V to 3.0V and -40°C ≤ TA ≤ 85°C, respectively. Typical parameters
apply to 5V, 3.3V, or 2.7V at 25°C and are for design guidance only.
Table 3-11. DC Switch Mode Pump (SMP) Specifications
Symbol
Description
Min
4.75
Typ
5.0
Max
5.25
Units
Notes
a
V
V
V
I
5V Output Voltage from Pump
V
V
V
Configuration of footnote. Average, neglecting
PUMP5V
ripple. SMP trip voltage is set to 5.0V.
a
3.3V Output Voltage from Pump
2.6V Output Voltage from Pump
Available Output Current
3.00
2.45
3.25
2.55
3.60
2.80
Configuration of footnote. Average, neglecting
PUMP3V
PUMP2V
ripple. SMP trip voltage is set to 3.25V.
a
Configuration of footnote. Average, neglecting
ripple. SMP trip voltage is set to 2.55V.
a
Configuration of footnote.
PUMP
V
V
V
= 1.8V, V
= 1.5V, V
= 1.3V, V
= 5.0V
5
8
8
–
–
–
–
–
–
mA
mA
mA
SMP trip voltage is set to 5.0V.
SMP trip voltage is set to 3.25V.
SMP trip voltage is set to 2.55V.
BAT
BAT
BAT
PUMP
PUMP
PUMP
= 3.25V
= 2.55V
a
V
Input Voltage Range from Battery
Input Voltage Range from Battery
Input Voltage Range from Battery
Minimum Input Voltage from Battery to Start Pump
Line Regulation (over Vi range)
1.8
1.0
1.0
1.2
–
–
–
–
–
5
5.0
3.3
2.8
–
V
Configuration of footnote. SMP trip voltage is
set to 5.0V.
BAT5V
a
V
V
V
V
Configuration of footnote. SMP trip voltage is
BAT3V
set to 3.25V.
a
V
Configuration of footnote. SMP trip voltage is
BAT2V
set to 2.55V.
a
o
V
Configuration of footnote. 0 C ≤ T ≤ 100.
BATSTART
A
o
1.25V at T = -40 C.
A
a
∆V
∆V
∆V
–
%V
Configuration of footnote.
V is the “Vdd Value
O
PUMP_Line
PUMP_Load
PUMP_Ripple
O
O
for PUMP Trip” specified by the VM[2:0] setting
in the DC POR and LVD Specification, Table 3-
13 on page 22.
a
Load Regulation
–
5
–
%V
Configuration of footnote.
V is the “Vdd Value
O
for PUMP Trip” specified by the VM[2:0] setting
in the DC POR and LVD Specification, Table 3-
13 on page 22.
a
Output Voltage Ripple (depends on cap/load)
Efficiency
–
100
50
–
–
mVpp
%
Configuration of footnote. Load is 5 mA.
a
E
3
35
Configuration of footnote. Load is 5 mA. SMP
trip voltage is set to 3.25V.
E
2
Efficiency
35
80
–
%
For I load = 1mA, V
= 2.55V, V
= 1.3V,
PUMP
BAT
10 uH inductor, 1 uF capacitor, and Schottky
diode.
F
Switching Frequency
Switching Duty Cycle
–
–
1.3
50
–
–
MHz
%
PUMP
DC
PUMP
a. L1 = 2 µH inductor, C1 = 10 µF capacitor, D1 = Schottky diode. See Figure 3-2.
Figure 3-2. Basic Switch Mode Pump Circuit
D1
Vdd
VPUMP
L1
SMP
Vss
+
C1
VBAT
Battery
PSoC
January 12, 2007
Document No. 38-12025 Rev. *K
21
[+] Feedback
CY8C21x34 Final Data Sheet
3. Electrical Specifications
3.3.6
DC Analog Mux Bus Specifications
The following table lists guaranteed maximum and minimum specifications for the voltage and temperature ranges: 4.75V to 5.25V
and -40°C ≤ TA ≤ 85°C, 3.0V to 3.6V and -40°C ≤ TA ≤ 85°C, or 2.4V to 3.0V and -40°C ≤ TA ≤ 85°C, respectively. Typical parameters
apply to 5V, 3.3V, or 2.7V at 25°C and are for design guidance only.
Table 3-12. DC Analog Mux Bus Specifications
Symbol
Description
Min
Typ
Max
400
800
Units
Notes
R
R
Switch Resistance to Common Analog Bus
–
–
–
–
Ω
Ω
Vdd ≥ 2.7V
2.4V ≤ Vdd ≤ 2.7V
SW
Resistance of Initialization Switch to Vdd
800
Ω
VDD
3.3.7
DC POR and LVD Specifications
The following table lists guaranteed maximum and minimum specifications for the voltage and temperature ranges: 4.75V to 5.25V
and -40°C ≤ TA ≤ 85°C, 3.0V to 3.6V and -40°C ≤ TA ≤ 85°C, or 2.4V to 3.0V and -40°C ≤ TA ≤ 85°C, respectively. Typical parameters
apply to 5V, 3.3V, or 2.7V at 25°C and are for design guidance only.
Table 3-13. DC POR and LVD Specifications
Symbol
Description
Vdd Value for PPOR Trip
Min
Typ
Max
Units
Notes
Vdd must be greater than or equal to 2.5V
during startup, reset from the XRES pin, or
reset from Watchdog.
V
V
V
PPOR0
PPOR1
PPOR2
PORLEV[1:0] = 00b
PORLEV[1:0] = 01b
PORLEV[1:0] = 10b
Vdd Value for LVD Trip
VM[2:0] = 000b
2.36
2.40
V
V
V
–
2.82
4.55
2.95
4.70
a
b
V
V
V
V
V
V
V
V
2.40
2.85
2.95
3.06
4.37
4.50
4.62
4.71
2.45
2.92
3.02
3.13
4.48
4.64
4.73
4.81
2.51
2.99
3.09
3.20
4.55
4.75
4.83
4.95
V
V
V
V
V
V
V
V
LVD0
LVD1
LVD2
LVD3
LVD4
LVD5
LVD6
LVD7
VM[2:0] = 001b
VM[2:0] = 010b
VM[2:0] = 011b
VM[2:0] = 100b
VM[2:0] = 101b
VM[2:0] = 110b
VM[2:0] = 111b
Vdd Value for PUMP Trip
VM[2:0] = 000b
VM[2:0] = 001b
VM[2:0] = 010b
VM[2:0] = 011b
VM[2:0] = 100b
VM[2:0] = 101b
VM[2:0] = 110b
VM[2:0] = 111b
c
V
V
V
V
V
V
V
V
2.45
2.96
3.03
3.18
4.54
4.62
4.71
4.89
2.55
3.02
3.10
3.25
4.64
4.73
4.82
5.00
V
V
V
V
V
V
V
V
2.62
3.09
3.16
3.32
4.74
4.83
4.92
5.12
PUMP0
PUMP1
PUMP2
PUMP3
PUMP4
PUMP5
PUMP6
PUMP7
d
a. Always greater than 50 mV above VPPOR (PORLEV = 00) for falling supply.
b. Always greater than 50 mV above VPPOR (PORLEV = 01) for falling supply.
c. Always greater than 50 mV above V
d. Always greater than 50 mV above V
.
.
LVD0
LVD3
January 12, 2007
Document No. 38-12025 Rev. *K
22
[+] Feedback
CY8C21x34 Final Data Sheet
3. Electrical Specifications
3.3.8
DC Programming Specifications
The following table lists guaranteed maximum and minimum specifications for the voltage and temperature ranges: 4.75V to 5.25V
and -40°C ≤ TA ≤ 85°C, 3.0V to 3.6V and -40°C ≤ TA ≤ 85°C, or 2.4V to 3.0V and -40°C ≤ TA ≤ 85°C, respectively. Typical parameters
apply to 5V, 3.3V, or 2.7V at 25°C and are for design guidance only.
Table 3-14. DC Programming Specifications
Symbol
Vdd
Description
Min
2.70
Typ
Max
Units
Notes
Supply Voltage for Flash Write Operations
Supply Current During Programming or Verify
Input Low Voltage During Programming or Verify
Input High Voltage During Programming or Verify
–
5
–
–
–
–
V
IWRITE
DDP
I
–
25
0.8
–
mA
V
V
ILP
V
IHP
–
2.2
–
V
I
Input Current when Applying Vilp to P1[0] or P1[1] During
Programming or Verify
0.2
mA
Driving internal pull-down resistor.
Driving internal pull-down resistor.
ILP
I
Input Current when Applying Vihp to P1[0] or P1[1] During
Programming or Verify
–
–
1.5
mA
IHP
V
V
Output Low Voltage During Programming or Verify
Output High Voltage During Programming or Verify
–
–
–
Vss + 0.75
Vdd
V
V
OLV
Vdd - 1.0
OHV
Flash
Flash
Flash
Flash Endurance (per block)
50,000
1,800,000
10
–
–
–
–
–
–
–
Erase/write cycles per block.
Erase/write cycles.
ENPB
ENT
DR
a
–
Flash Endurance (total)
Flash Data Retention
Years
a. A maximum of 36 x 50,000 block endurance cycles is allowed. This may be balanced between operations on 36x1 blocks of 50,000 maximum cycles each, 36x2 blocks of
25,000 maximum cycles each, or 36x4 blocks of 12,500 maximum cycles each (to limit the total number of cycles to 36x50,000 and that no single block ever sees more than
50,000 cycles).
For the full industrial range, the user must employ a temperature sensor user module (FlashTemp) and feed the result to the temperature argument before writing. Refer to
the Flash APIs Application Note AN2015 at http://www.cypress.com under Application Notes for more information.
January 12, 2007
Document No. 38-12025 Rev. *K
23
[+] Feedback
CY8C21x34 Final Data Sheet
3. Electrical Specifications
3.4
AC Electrical Characteristics
3.4.1
AC Chip-Level Specifications
The following tables list guaranteed maximum and minimum specifications for the voltage and temperature ranges: 4.75V to 5.25V
and -40°C ≤ TA ≤ 85°C, 3.0V to 3.6V and -40°C ≤ TA ≤ 85°C, or 2.4V to 3.0V and -40°C ≤ TA ≤ 85°C, respectively. Typical parameters
apply to 5V, 3.3V, or 2.7V at 25°C and are for design guidance only.
Table 3-15. 5V and 3.3V AC Chip-Level Specifications
Symbol
Description
Min
23.4
Typ
Max
Units
MHz
Notes
a,b,c
F
F
Internal Main Oscillator Frequency for 24 MHz
24
6
Trimmed for 5V or 3.3V operation using
factory trim values. See Figure 3-1b on
page 17. SLIMO mode = 0.
24.6
IMO24
a,b,c
Internal Main Oscillator Frequency for 6 MHz
5.75
MHz
Trimmed for 5V or 3.3V operation using
factory trim values. See Figure 3-1b on
page 17. SLIMO mode = 1.
6.35
IMO6
a,b
F
F
F
CPU Frequency (5V Nominal)
CPU Frequency (3.3V Nominal)
0.93
0.93
0
24
12
48
MHz
MHz
MHz
24 MHz only for SLIMO mode = 0.
24.6
12.3
49.2
CPU1
CPU2
BLK5
b,c
0
a,b,d
Refer to the AC Digital Block Specifica-
tions below.
Digital PSoC Block Frequency (5V Nominal)
b,d
F
F
Digital PSoC Block Frequency (3.3V Nominal)
Internal Low Speed Oscillator Frequency
32 kHz RMS Period Jitter
0
24
32
MHz
kHz
ns
24.6
64
200
–
BLK33
32K1
15
–
Jitter32k
Jitter32k
100
1400
–
32 kHz Peak-to-Peak Period Jitter
External Reset Pulse Width
–
T
10
40
–
–
µs
XRST
DC24M
24 MHz Duty Cycle
50
60
–
%
Step24M
Fout48M
Jitter24M1
24 MHz Trim Step Size
50
kHz
MHz
ps
a,c
48 MHz Output Frequency
46.8
–
48.0
600
–
Trimmed. Utilizing factory trim values.
49.2
24 MHz Peak-to-Peak Period Jitter (IMO)
Maximum frequency of signal on row input or row output.
Supply Ramp Time
F
T
–
12.3
–
MHz
µs
MAX
0
–
RAMP
a. 4.75V < Vdd < 5.25V.
b. Accuracy derived from Internal Main Oscillator with appropriate trim for Vdd range.
c. 3.0V < Vdd < 3.6V. See Application Note AN2012 “Adjusting PSoC Microcontroller Trims for Dual Voltage-Range Operation” for information on trimming for operation at 3.3V.
d. See the individual user module data sheets for information on maximum frequencies for user modules.
Table 3-16. 2.7V AC Chip-Level Specifications
Symbol
Description
Min
11.5
Typ
Max
Units
MHz
Notes
0
a,b,c
F
F
Internal Main Oscillator Frequency for 12 MHz
Trimmed for 2.7V operation using factory
trim values. See Figure 3-1b on page 17.
SLIMO mode = 1.
12
6
12.7
IMO12
a,b,c
Internal Main Oscillator Frequency for 6 MHz
5.75
MHz
Trimmed for 2.7V operation using factory
trim values. See Figure 3-1b on page 17.
SLIMO mode = 1.
6.35
IMO6
a,b
F
F
CPU Frequency (2.7V Nominal)
0.093
0
3
MHz
MHz
24 MHz only for SLIMO mode = 0.
3.15
12.5
CPU1
a,b,c
Digital PSoC Block Frequency (2.7V Nominal)
12
Refer to the AC Digital Block Specifica-
tions below.
BLK27
F
Internal Low Speed Oscillator Frequency
32 kHz RMS Period Jitter
8
32
96
200
–
kHz
ns
32K1
Jitter32k
Jitter32k
–
150
1400
–
32 kHz Peak-to-Peak Period Jitter
External Reset Pulse Width
–
T
10
–
–
µs
XRST
F
T
Maximum frequency of signal on row input or row output.
Supply Ramp Time
–
12.3
–
MHz
µs
MAX
0
–
RAMP
a. 2.4V < Vdd < 3.0V.
b. Accuracy derived from Internal Main Oscillator with appropriate trim for Vdd range.
c. See Application Note AN2012 “Adjusting PSoC Microcontroller Trims for Dual Voltage-Range Operation” for information on maximum frequency for user modules.
January 12, 2007
Document No. 38-12025 Rev. *K
24
[+] Feedback
CY8C21x34 Final Data Sheet
3. Electrical Specifications
Figure 3-3. 24 MHz Period Jitter (IMO) Timing Diagram
Jitter24M1
F24M
Figure 3-4. 32 kHz Period Jitter (ILO) Timing Diagram
Jitter32k
F32K1
January 12, 2007
Document No. 38-12025 Rev. *K
25
[+] Feedback
CY8C21x34 Final Data Sheet
3. Electrical Specifications
3.4.2
AC General Purpose IO Specifications
The following tables list guaranteed maximum and minimum specifications for the voltage and temperature ranges: 4.75V to 5.25V
and -40°C ≤ TA ≤ 85°C, 3.0V to 3.6V and -40°C ≤ TA ≤ 85°C, or 2.4V to 3.0V and -40°C ≤ TA ≤ 85°C, respectively. Typical parameters
apply to 5V, 3.3V, or 2.7V at 25°C and are for design guidance only.
Table 3-17. 5V and 3.3V AC GPIO Specifications
Symbol
Description
GPIO Operating Frequency
Min
Typ
Max
Units
MHz
Notes
Normal Strong Mode
F
0
3
2
7
7
–
12
18
18
–
GPIO
TRiseF
TFallF
TRiseS
TFallS
Rise Time, Normal Strong Mode, Cload = 50 pF
Fall Time, Normal Strong Mode, Cload = 50 pF
Rise Time, Slow Strong Mode, Cload = 50 pF
Fall Time, Slow Strong Mode, Cload = 50 pF
–
ns
ns
ns
ns
Vdd = 4.5 to 5.25V, 10% - 90%
Vdd = 4.5 to 5.25V, 10% - 90%
Vdd = 3 to 5.25V, 10% - 90%
Vdd = 3 to 5.25V, 10% - 90%
–
27
22
–
Table 3-18. 2.7V AC GPIO Specifications
Symbol
Description
GPIO Operating Frequency
Min
Typ
Max
Units
Notes
Normal Strong Mode
F
0
–
3
MHz
ns
GPIO
TRiseF
TFallF
TRiseS
TFallS
Rise Time, Normal Strong Mode, Cload = 50 pF
Fall Time, Normal Strong Mode, Cload = 50 pF
Rise Time, Slow Strong Mode, Cload = 50 pF
Fall Time, Slow Strong Mode, Cload = 50 pF
6
–
50
50
Vdd = 2.4 to 3.0V, 10% - 90%
Vdd = 2.4 to 3.0V, 10% - 90%
Vdd = 2.4 to 3.0V, 10% - 90%
Vdd = 2.4 to 3.0V, 10% - 90%
6
–
ns
18
18
40
40
120
120
ns
ns
Figure 3-5. GPIO Timing Diagram
90%
GPIO
Pin
Output
Voltage
10%
TRiseF
TRiseS
TFallF
TFallS
January 12, 2007
Document No. 38-12025 Rev. *K
26
[+] Feedback
CY8C21x34 Final Data Sheet
3. Electrical Specifications
3.4.3
AC Operational Amplifier Specifications
The following table lists guaranteed maximum and minimum specifications for the voltage and temperature ranges: 4.75V to 5.25V
and -40°C ≤ TA ≤ 85°C, 3.0V to 3.6V and -40°C ≤ TA ≤ 85°C, or 2.4V to 3.0V and -40°C ≤ TA ≤ 85°C, respectively. Typical parameters
apply to 5V, 3.3V, or 2.7V at 25°C and are for design guidance only.
Table 3-19. AC Operational Amplifier Specifications
Symbol
Description
Min
Typ
Max
100
200
Units
ns
ns
Notes
T
Comparator Mode Response Time, 50 mV Overdrive
Vdd ≥ 3.0V.
2.4V < Vcc < 3.0V.
COMP
3.4.4
AC Low Power Comparator Specifications
The following table lists guaranteed maximum and minimum specifications for the voltage and temperature ranges: 4.75V to 5.25V
and -40°C ≤ TA ≤ 85°C, 3.0V to 3.6V and -40°C ≤ TA ≤ 85°C, or 2.4V to 3.0V and -40°C ≤ TA ≤ 85°C, respectively. Typical parameters
apply to 5V at 25°C and are for design guidance only.
Table 3-20. AC Low Power Comparator Specifications
Symbol
Description
Min
Typ
Max
Units
µs
Notes
T
LPC response time
–
–
50
≥ 50 mV overdrive comparator reference set
RLPC
within V
.
REFLPC
3.4.5
AC Analog Mux Bus Specifications
The following table lists guaranteed maximum and minimum specifications for the voltage and temperature ranges: 4.75V to 5.25V
and -40°C ≤ TA ≤ 85°C, 3.0V to 3.6V and -40°C ≤ TA ≤ 85°C, or 2.4V to 3.0V and -40°C ≤ TA ≤ 85°C, respectively. Typical parameters
apply to 5V, 3.3V, or 2.7V at 25°C and are for design guidance only.
Table 3-21. AC Analog Mux Bus Specifications
Symbol
Description
Min
Typ
Max
3.17
Units
MHz
Notes
F
Switch Rate
–
–
SW
3.4.6
AC Digital Block Specifications
The following tables list guaranteed maximum and minimum specifications for the voltage and temperature ranges: 4.75V to 5.25V
and -40°C ≤ TA ≤ 85°C, 3.0V to 3.6V and -40°C ≤ TA ≤ 85°C, or 2.4V to 3.0V and -40°C ≤ TA ≤ 85°C, respectively. Typical parameters
apply to 5V, 3.3V, or 2.7V at 25°C and are for design guidance only.
Table 3-22. 5V and 3.3V AC Digital Block Specifications
Function
Description
Maximum Block Clocking Frequency (> 4.75V)
Maximum Block Clocking Frequency (< 4.75V)
Capture Pulse Width
Min
Typ
Max
49.2
Units
MHz
Notes
4.75V < Vdd < 5.25V.
All
Functions
Timer
24.6
–
MHz
ns
3.0V < Vdd < 4.75V.
a
–
–
–
–
–
–
50
Maximum Frequency, No Capture
Maximum Frequency, With or Without Capture
Enable Pulse Width
–
49.2
24.6
–
MHz
MHz
ns
4.75V < Vdd < 5.25V.
–
Counter
50
–
Maximum Frequency, No Enable Input
Maximum Frequency, Enable Input
49.2
24.6
MHz
MHz
4.75V < Vdd < 5.25V.
–
Dead Band Kill Pulse Width:
Asynchronous Restart Mode
20
50
50
–
–
–
–
–
–
–
ns
Synchronous Restart Mode
Disable Mode
–
ns
–
ns
Maximum Frequency
49.2
49.2
MHz
MHz
4.75V < Vdd < 5.25V.
4.75V < Vdd < 5.25V.
CRCPRS
Maximum Input Clock Frequency
–
(PRS Mode)
January 12, 2007
Document No. 38-12025 Rev. *K
27
[+] Feedback
CY8C21x34 Final Data Sheet
3. Electrical Specifications
Table 3-22. 5V and 3.3V AC Digital Block Specifications (continued)
CRCPRS
(CRC Mode)
Maximum Input Clock Frequency
–
–
24.6
8.2
MHz
MHz
SPIM
Maximum Input Clock Frequency
–
–
Maximum data rate at 4.1 MHz due to 2 x over
clocking.
SPIS
Maximum Input Clock Frequency
–
–
–
–
4.1
–
MHz
ns
Width of SS_ Negated Between Transmissions
50
–
Transmitter Maximum Input Clock Frequency
24.6
MHz
Maximum data rate at 3.08 MHz due to 8 x over
clocking.
Maximum Input Clock Frequency with Vdd ≥ 4.75V, 2
Stop Bits
–
–
49.2
MHz
Maximum data rate at 6.15 MHz due to 8 x over
clocking.
Receiver
Maximum Input Clock Frequency
–
–
–
–
24.6
49.2
MHz
MHz
Maximum data rate at 3.08 MHz due to 8 x over
clocking.
Maximum data rate at 6.15 MHz due to 8 x over
clocking.
Maximum Input Clock Frequency with Vdd ≥ 4.75V, 2
Stop Bits
a. 50 ns minimum input pulse width is based on the input synchronizers running at 12 MHz (84 ns nominal period).
Table 3-23. 2.7V AC Digital Block Specifications
Function
Description
Min
Typ
Max
12.7
Units
MHz
Notes
All
Maximum Block Clocking Frequency
2.4V < Vdd < 3.0V.
Functions
Timer
a
Capture Pulse Width
–
–
–
–
–
–
ns
100
Maximum Frequency, With or Without Capture
Enable Pulse Width
–
12.7
–
MHz
ns
Counter
100
–
Maximum Frequency, No Enable Input
Maximum Frequency, Enable Input
12.7
12.7
MHz
MHz
–
Dead Band Kill Pulse Width:
Asynchronous Restart Mode
20
100
100
–
–
–
–
–
–
–
ns
Synchronous Restart Mode
Disable Mode
–
ns
–
ns
Maximum Frequency
12.7
12.7
MHz
MHz
CRCPRS
Maximum Input Clock Frequency
–
(PRS Mode)
CRCPRS
(CRC Mode)
Maximum Input Clock Frequency
Maximum Input Clock Frequency
–
–
–
–
12.7
6.35
MHz
MHz
SPIM
Maximum data rate at 3.17 MHz due to 2 x over
clocking.
SPIS
Maximum Input Clock Frequency
–
–
–
–
4.1
–
MHz
ns
Width of SS_ Negated Between Transmissions
100
–
Transmitter Maximum Input Clock Frequency
12.7
MHz
Maximum data rate at 1.59 MHz due to 8 x over
clocking.
Receiver Maximum Input Clock Frequency
–
–
12.7
MHz
Maximum data rate at 1.59 MHz due to 8 x over
clocking.
a. 100 ns minimum input pulse width is based on the input synchronizers running at 12 MHz (84 ns nominal period).
January 12, 2007
Document No. 38-12025 Rev. *K
28
[+] Feedback
CY8C21x34 Final Data Sheet
3. Electrical Specifications
3.4.7
AC External Clock Specifications
The following tables list guaranteed maximum and minimum specifications for the voltage and temperature ranges: 4.75V to 5.25V
and -40°C ≤ TA ≤ 85°C, or 3.0V to 3.6V and -40°C ≤ TA ≤ 85°C, respectively. Typical parameters apply to 5V, 3.3V, or 2.7V at 25°C
and are for design guidance only.
Table 3-24. 5V AC External Clock Specifications
Symbol
Description
Min
0.093
Typ
Max
24.6
Units
MHz
Notes
F
–
–
–
Frequency
High Period
Low Period
–
–
–
–
OSCEXT
20.6
20.6
150
5300
ns
ns
µs
–
–
Power Up IMO to Switch
Table 3-25. 3.3V AC External Clock Specifications
Symbol
Description
Min
Typ
Max
Units
Notes
F
F
Frequency with CPU Clock divide by 1
0.093
–
–
MHz
Maximum CPU frequency is 12 MHz at 3.3V.
With the CPU clock divider set to 1, the external
clock must adhere to the maximum frequency
and duty cycle requirements.
12.3
OSCEXT
Frequency with CPU Clock divide by 2 or greater
0.186
24.6
MHz
If the frequency of the external clock is greater
than 12 MHz, the CPU clock divider must be set
to 2 or greater. In this case, the CPU clock
divider will ensure that the fifty percent duty
cycle requirement is met.
OSCEXT
–
–
–
High Period with CPU Clock divide by 1
Low Period with CPU Clock divide by 1
Power Up IMO to Switch
41.7
41.7
150
–
–
–
5300
ns
ns
µs
–
–
Table 3-26. 2.7V AC External Clock Specifications
Symbol
Description
Min
Typ
Max
Units
Notes
0
F
F
Frequency with CPU Clock divide by 1
0.093
–
–
MHz
Maximum CPU frequency is 3 MHz at 2.7V.
With the CPU clock divider set to 1, the external
clock must adhere to the maximum frequency
and duty cycle requirements.
3.08
OSCEXT
Frequency with CPU Clock divide by 2 or greater
0.186
6.35
MHz
If the frequency of the external clock is greater
than 3 MHz, the CPU clock divider must be set
to 2 or greater. In this case, the CPU clock
divider will ensure that the fifty percent duty
cycle requirement is met.
OSCEXT
–
–
–
High Period with CPU Clock divide by 1
Low Period with CPU Clock divide by 1
Power Up IMO to Switch
160
160
150
–
–
–
5300
ns
ns
µs
–
–
January 12, 2007
Document No. 38-12025 Rev. *K
29
[+] Feedback
CY8C21x34 Final Data Sheet
3. Electrical Specifications
3.4.8
AC Programming Specifications
The following table lists guaranteed maximum and minimum specifications for the voltage and temperature ranges: 4.75V to 5.25V
and -40°C ≤ TA ≤ 85°C, or 3.0V to 3.6V and -40°C ≤ TA ≤ 85°C, respectively. Typical parameters apply to 5V, 3.3V, or 2.7V at 25°C
and are for design guidance only.
Table 3-27. AC Programming Specifications
Symbol
Description
Min
Typ
Max
Units
ns
Notes
T
Rise Time of SCLK
Fall Time of SCLK
1
–
20
20
–
RSCLK
FSCLK
SSCLK
HSCLK
SCLK
T
T
T
F
T
T
T
T
T
1
–
ns
Data Set up Time to Falling Edge of SCLK
Data Hold Time from Falling Edge of SCLK
Frequency of SCLK
40
40
0
–
ns
–
–
ns
–
8
MHz
ms
ms
ns
Flash Erase Time (Block)
–
15
30
–
–
ERASEB
WRITE
DSCLK
DSCLK3
DSCLK2
Flash Block Write Time
–
–
Data Out Delay from Falling Edge of SCLK
Data Out Delay from Falling Edge of SCLK
Data Out Delay from Falling Edge of SCLK
–
45
50
70
3.6 < Vdd
–
–
ns
3.0 ≤ Vdd ≤ 3.6
2.4 ≤ Vdd ≤ 3.0
–
–
ns
January 12, 2007
Document No. 38-12025 Rev. *K
30
[+] Feedback
CY8C21x34 Final Data Sheet
3. Electrical Specifications
2
3.4.9
AC I C Specifications
The following tables list guaranteed maximum and minimum specifications for the voltage and temperature ranges: 4.75V to 5.25V
and -40°C ≤ TA ≤ 85°C, 3.0V to 3.6V and -40°C ≤ TA ≤ 85°C, or 2.4V to 3.0V and -40°C ≤ TA ≤ 85°C, respectively. Typical parameters
apply to 5V, 3.3V, or 2.7V at 25°C and are for design guidance only.
Table 3-28. AC Characteristics of the I2C SDA and SCL Pins for Vdd ≥ 3.0V
Standard Mode
Min Max
100
Fast Mode
Min Max
Symbol
SCLI2C
Description
SCL Clock Frequency
Units
kHz
Notes
F
T
0
0
400
–
Hold Time (repeated) START Condition. After this
period, the first clock pulse is generated.
4.0
–
0.6
µs
HDSTAI2C
T
T
T
T
T
T
T
T
LOW Period of the SCL Clock
HIGH Period of the SCL Clock
Set-up Time for a Repeated START Condition
Data Hold Time
4.7
4.0
4.7
0
–
–
–
–
–
–
–
–
1.3
0.6
0.6
0
–
µs
µs
µs
µs
ns
µs
µs
ns
LOWI2C
–
HIGHI2C
SUSTAI2C
HDDATI2C
SUDATI2C
SUSTOI2C
BUFI2C
–
–
a
Data Set-up Time
250
4.0
–
100
0.6
1.3
0
Set-up Time for STOP Condition
–
Bus Free Time Between a STOP and START Condition 4.7
–
Pulse Width of spikes are suppressed by the input fil-
ter.
–
50
SPI2C
a. A Fast-Mode I2C-bus device can be used in a Standard-Mode I2C-bus system, but the requirement tSU;DAT ≥ 250 ns must then be met. This will automatically be
the case if the device does not stretch the LOW period of the SCL signal. If such device does stretch the LOW period of the SCL signal, it must output the next data
bit to the SDA line trmax + tSU;DAT = 1000 + 250 = 1250 ns (according to the Standard-Mode I2C-bus specification) before the SCL line is released.
Table 3-29. 2.7V AC Characteristics of the I2C SDA and SCL Pins (Fast Mode not Supported)
Standard Mode
Min Max
100
Fast Mode
Min Max
Symbol
SCLI2C
Description
SCL Clock Frequency
Units
kHz
Notes
F
T
0
–
–
–
–
Hold Time (repeated) START Condition. After this
period, the first clock pulse is generated.
4.0
–
µs
HDSTAI2C
T
T
T
T
T
T
T
T
LOW Period of the SCL Clock
HIGH Period of the SCL Clock
Set-up Time for a Repeated START Condition
Data Hold Time
4.7
4.0
4.7
0
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
µs
µs
µs
µs
ns
µs
µs
ns
LOWI2C
HIGHI2C
SUSTAI2C
HDDATI2C
SUDATI2C
SUSTOI2C
BUFI2C
Data Set-up Time
250
4.0
Set-up Time for STOP Condition
Bus Free Time Between a STOP and START Condition 4.7
Pulse Width of spikes are suppressed by the input fil-
ter.
–
SPI2C
Figure 3-6. Definition for Timing for Fast/Standard Mode on the I2C Bus
SDA
SCL
TSPI2C
T
LOWI2C
TSUDATI2C
THDSTAI2C
TBUFI2C
TSUSTOI2C
TSUSTAI2C
THDDATI2C
THDSTAI2C
THIGHI2C
S
Sr
P
S
January 12, 2007
Document No. 38-12025 Rev. *K
31
[+] Feedback
4. Packaging Information
This chapter illustrates the packaging specifications for the CY8C21x34 PSoC device, along with the thermal impedances for each
package.
Important Note Emulation tools may require a larger area on the target PCB than the chip’s footprint. For a detailed description of
the emulation tools’ dimensions, refer to the document titled PSoC Emulator Pod Dimensions at
http://www.cypress.com/design/MR10161.
4.1
Packaging Dimensions
51-85068 *B
Figure 4-1. 16-Lead (150-Mil) SOIC
January 12, 2007
Document No. 38-12025 Rev. *K
32
[+] Feedback
CY8C21x34 Final Data Sheet
4. Packaging Information
51-85077 *C
Figure 4-2. 20-Lead (210-MIL) SSOP
51-85079 *C
Figure 4-3. 28-Lead (210-Mil) SSOP
January 12, 2007
Document No. 38-12025 Rev. *K
33
[+] Feedback
CY8C21x34 Final Data Sheet
4. Packaging Information
E-PAD X, Y for this product is 3.53 mm, 3.53 mm (+/-0.11 mm)
51-85188 *A
Figure 4-4. 32-Lead (5x5 mm 0.93 MAX) QFN
E-PAD X, Y for this product is 3.53 mm, 3.53 mm (+/-0.11 mm)
001-06392 *A
Figure 4-5. 32-Lead (5x5 mm 0.60 MAX) QFN
January 12, 2007
Document No. 38-12025 Rev. *K
34
[+] Feedback
CY8C21x34 Final Data Sheet
4. Packaging Information
Important Note For information on the preferred dimensions for mounting QFN packages, see the following Application Note at
http://www.amkor.com/products/notes_papers/MLFAppNote.pdf.
51-85062 *C
Figure 4-6. 56-Lead (300-Mil) SSOP
January 12, 2007
Document No. 38-12025 Rev. *K
35
[+] Feedback
CY8C21x34 Final Data Sheet
4. Packaging Information
4.2
Thermal Impedances
Table 4-1. Thermal Impedances per Package
Package
16 SOIC
Typical θJA
*
Typical θJC
o
o
123 C/W
55 C/W
o
o
20 SSOP
117 C/W
41 C/W
o
o
28 SSOP
96 C/W
39 C/W
o
o
32 QFN** 5x5 mm 0.60 MAX
32 QFN** 5x5 mm 0.93 MAX
* T = T + Power x θ
27 C/W
15 C/W
o
o
22 C/W
12 C/W
J
A
JA
** To achieve the thermal impedance specified for the QFN package, the center thermal pad should be soldered to the
PCB ground plane.
4.3
Solder Reflow Peak Temperature
Following is the minimum solder reflow peak temperature to achieve good solderability.
Table 4-2. Solder Reflow Peak Temperature
Package
Minimum Peak Temperature*
Maximum Peak Temperature
o
o
16 SOIC
240 C
260 C
o
o
20 SSOP
28 SSOP
32 QFN
240 C
260 C
o
o
240 C
260 C
o
o
240 C
260 C
o
*Higher temperatures may be required based on the solder melting point. Typical temperatures for solder are 220 ± 5 C
o
with Sn-Pb or 245 ± 5 C with Sn-Ag-Cu paste. Refer to the solder manufacturer specifications.
January 12, 2007
Document No. 38-12025 Rev. *K
36
[+] Feedback
5. Development Tool Selection
This chapter presents the development tools available for all current PSoC device families including the CY8C21x34 family.
5.1
Software
5.2
Development Kits
All development kits can be purchased from the Cypress Online
Store.
5.1.1
PSoC Designer™
At the core of the PSoC development software suite is PSoC
Designer. Utilized by thousands of PSoC developers, this
robust software has been facilitating PSoC designs for half a
decade. PSoC Designer is available free of charge at http://
www.cypress.com under DESIGN RESOURCES >> Software
and Drivers.
5.2.1
CY3215-DK Basic Development Kit
The CY3215-DK is for prototyping and development with PSoC
Designer. This kit supports in-circuit emulation and the software
interface allows users to run, halt, and single step the processor
and view the content of specific memory locations. Advance
emulation features also supported through PSoC Designer. The
kit includes:
5.1.2
PSoC Express™
■ PSoC Designer Software CD
As the newest addition to the PSoC development software
suite, PSoC Express is the first visual embedded system design
tool that allows a user to create an entire PSoC project and
generate a schematic, BOM, and data sheet without writing a
single line of code. Users work directly with application objects
such as LEDs, switches, sensors, and fans. PSoC Express is
available free of charge at http://www.cypress.com/psocex-
press.
■ ICE-Cube In-Circuit Emulator
■ ICE Flex-Pod for CY8C29x66 Family
■ Cat-5 Adapter
■ Mini-Eval Programming Board
■ 110 ~ 240V Power Supply, Euro-Plug Adapter
■ iMAGEcraft C Compiler (Registration Required)
■ ISSP Cable
5.1.3
PSoC Programmer
■ USB 2.0 Cable and Blue Cat-5 Cable
■ 2 CY8C29466-24PXI 28-PDIP Chip Samples
Flexible enough to be used on the bench in development, yet
suitable for factory programming, PSoC Programmer works
either as a standalone programming application or it can oper-
ate directly from PSoC Designer or PSoC Express. PSoC Pro-
grammer software is compatible with both PSoC ICE-Cube In-
Circuit Emulator and PSoC MiniProg. PSoC programmer is
available free ofcharge at http://www.cypress.com/psocpro-
grammer.
5.1.4
CY3202-C iMAGEcraft C Compiler
CY3202 is the optional upgrade to PSoC Designer that enables
the iMAGEcraft C compiler. It can be purchased from the
Cypress Online Store. At http://www.cypress.com, click the
Online Store shopping cart icon at the bottom of the web page,
and click PSoC (Programmable System-on-Chip) to view a cur-
rent list of available items..
January 12, 2007
Document No. 38-12025 Rev. *K
37
[+] Feedback
CY8C21x34 Final Data Sheet
5. Development Tool Selection
5.2.2
CY3210-ExpressDK PSoC Express
Development Kit
5.3.3
CY3214-PSoCEvalUSB
The CY3214-PSoCEvalUSB evaluation kit features a develop-
ment board for the CY8C24794-24LFXI PSoC device. Special
features of the board include both USB and capacitive sensing
development and debugging support. This evaluation board
also includes an LCD module, potentiometer, LEDs, an enunci-
ator and plenty of bread boarding space to meet all of your eval-
uation needs. The kit includes:
The CY3210-ExpressDK is for advanced prototyping and devel-
opment with PSoC Express (may be used with ICE-Cube In-Cir-
cuit Emulator). It provides access to I2C buses, voltage
reference, switches, upgradeable modules and more. The kit
includes:
■ PSoC Express Software CD
■ Express Development Board
■ 4 Fan Modules
■ PSoCEvalUSB Board
■ LCD Module
■ MIniProg Programming Unit
■ Mini USB Cable
■ 2 Proto Modules
■ MiniProg In-System Serial Programmer
■ MiniEval PCB Evaluation Board
■ Jumper Wire Kit
■ PSoC Designer and Example Projects CD
■ Getting Started Guide
■ Wire Pack
■ USB 2.0 Cable
■ Serial Cable (DB9)
5.4
Device Programmers
■ 110 ~ 240V Power Supply, Euro-Plug Adapter
■ 2 CY8C24423A-24PXI 28-PDIP Chip Samples
■ 2 CY8C27443-24PXI 28-PDIP Chip Samples
■ 2 CY8C29466-24PXI 28-PDIP Chip Samples
All device programmers can be purchased from the Cypress
Online Store.
5.4.1
CY3216 Modular Programmer
5.3
Evaluation Tools
The CY3216 Modular Programmer kit features a modular pro-
grammer and the MiniProg1 programming unit. The modular
programmer includes three programming module cards and
supports multiple Cypress products. The kit includes:
All evaluation tools can be purchased from the Cypress Online
Store.
■ Modular Programmer Base
■ 3 Programming Module Cards
■ MiniProg Programming Unit
■ PSoC Designer Software CD
■ Getting Started Guide
5.3.1
CY3210-MiniProg1
The CY3210-MiniProg1 kit allows a user to program PSoC
devices via the MiniProg1 programming unit. The MiniProg is a
small, compact prototyping programmer that connects to the PC
via a provided USB 2.0 cable. The kit includes:
■ USB 2.0 Cable
■ MiniProg Programming Unit
■ MiniEval Socket Programming and Evaluation Board
■ 28-Pin CY8C29466-24PXI PDIP PSoC Device Sample
■ 28-Pin CY8C27443-24PXI PDIP PSoC Device Sample
■ PSoC Designer Software CD
5.4.2
CY3207ISSP In-System Serial
Programmer (ISSP)
The CY3207ISSP is a production programmer. It includes pro-
tection circuitry and an industrial case that is more robust than
the MiniProg in a production-programming environment.
Note: CY3207ISSP needs special software and is not compati-
ble with PSoC Programmer. The kit includes:
■ Getting Started Guide
■ USB 2.0 Cable
5.3.2
CY3210-PSoCEval1
■ CY3207 Programmer Unit
■ PSoC ISSP Software CD
The CY3210-PSoCEval1 kit features an evaluation board and
the MiniProg1 programming unit. The evaluation board includes
an LCD module, potentiometer, LEDs, and plenty of bread-
boarding space to meet all of your evaluation needs. The kit
includes:
■ 110 ~ 240V Power Supply, Euro-Plug Adapter
■ USB 2.0 Cable
■ Evaluation Board with LCD Module
■ MiniProg Programming Unit
■ 28-Pin CY8C29466-24PXI PDIP PSoC Device Sample (2)
■ PSoC Designer Software CD
■ Getting Started Guide
■ USB 2.0 Cable
January 12, 2007
Document No. 38-12025 Rev. *K
38
[+] Feedback
CY8C21x34 Final Data Sheet
5. Development Tool Selection
5.5
Accessories (Emulation and
Programming)
Table 5-1. Emulation and Programming Accessories
a
b
c
Part #
Pin
Package
Flex-Pod Kit
Foot Kit
Adapter
CY8C21234 16 SOIC
-24S
CY3250-21X34 CY3250-
See note c. below
See note c. below
See note c. below
See note c. below
See note c. below
16SOIC-FK
CY8C21334 20 SSOP
-24PVXI
CY3250-21X34 CY3250-
20SSOP-FK
CY8C21434 32 QFN
-24LFXI
CY3250-
CY3250-
21X34QFN
32QFN-FK
CY8C21534 28 SSOP
-24PVXI
CY3250-21X34 CY3250-
28SSOP-FK
CY8C21634 32 QFN
-24LFXI
CY3250-
21X34QFN
CY3250-
32QFN-FK
a. Flex-Pod kit includes a practice flex-pod and a practice PCB, in addition to two
flex-pods.
b. Foot kit includes surface mount feet that can be soldered to the target PCB.
c. Programming adapter converts non-DIP package to DIP footprint. Specific
details and ordering information for each of the adapters can be found at
http://www.emulation.com.
5.6
3rd-Party Tools
Several tools have been specially designed by the following
3rd-party vendors to accompany PSoC devices during develop-
ment and production. Specific details for each of these tools can
be found at http://www.cypress.com under DESIGN
RESOURCES >> Evaluation Boards.
5.7
Build a PSoC Emulator into
Your Board
For details on how to emulate your circuit before going to vol-
ume production using an on-chip debug (OCD) non-production
PSoC device, see Application Note “Debugging - Build a PSoC
Emulator into Your Board - AN2323” at http://www.cypress.com/
an2323.
January 12, 2007
Document No. 38-12025 Rev. *K
39
[+] Feedback
6. Ordering Information
.
CY8C21x34 PSoC Device Key Features and Ordering Information
12a
12a
16a
16a
24a
24a
28a
28a
28a
28a
26a
26a
26a
16 Pin (150-Mil) SOIC
CY8C21234-24SXI
CY8C21234-24SXIT
CY8C21334-24PVXI
CY8C21334-24PVXIT
CY8C21534-24PVXI
CY8C21534-24PVXIT
CY8C21434-24LFXI
CY8C21434-24LFXIT
CY8C21434-24LKXI
CY8C21434-24LKXIT
CY8C21634-24LFXI
CY8C21634-24LFXIT
CY8C21001-24PVXI
8K
8K
8K
8K
8K
8K
8K
8K
8K
8K
8K
8K
8K
512
512
512
512
512
512
512
512
512
512
512
512
512
Yes -40°C to +85°C
Yes -40°C to +85°C
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
12
12
16
16
24
24
28
28
28
28
26
26
26
0
0
0
0
0
0
0
0
0
0
0
0
0
No
No
16 Pin (150-Mil) SOIC
(Tape and Reel)
20 Pin (210-Mil) SSOP
No
No
No
No
No
No
No
No
-40°C to +85°C
-40°C to +85°C
-40°C to +85°C
-40°C to +85°C
-40°C to +85°C
-40°C to +85°C
-40°C to +85°C
-40°C to +85°C
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
20 Pin (210-Mil) SSOP
(Tape and Reel)
28 Pin (210-Mil) SSOP
28 Pin (210-Mil) SSOP
(Tape and Reel)
32 Pin (5x5 mm 0.93 MAX) QFN b
32 Pin (5x5 mm 0.93 MAX) QFN b
(Tape and Reel)
32 Pin (5x5 mm 0.60 MAX) QFN b
32 Pin (5x5 mm 0.06 MAX) QFN b
(Tape and Reel)
32 Pin (5x5 mm 0.93 MAX) QFN b
Yes -40°C to +85°C
Yes -40°C to +85°C
Yes -40°C to +85°C
32 Pin (5x5 mm 0.93 MAX) QFN b
(Tape and Reel)
56 Pin OCD SSOP
a. All Digital IO Pins also connect to the common analog mux.
b. Refer to the “32-Pin Part Pinout” on page 11 for pin differences.
6.1
Ordering Code Definitions
CY 8 C 21 xxx-24xx
Package Type:
Thermal Rating:
C = Commercial
I = Industrial
PX = PDIP Pb-Free
SX = SOIC Pb-Free
PVX = SSOP Pb-Free
LFX/LKX = QFN Pb-Free
AX = TQFP Pb-Free
E = Extended
Speed: 24 MHz
Part Number
Family Code
Technology Code: C = CMOS
Marketing Code: 8 = Cypress PSoC
Company ID: CY = Cypress
January 12, 2007
Document No. 38-12025 Rev. *K
40
[+] Feedback
7. Sales and Service Information
Cypress Semiconductor
198 Champion Court
San Jose, CA 95134
408.943.2600
Web Sites:
Company Information – http://www.cypress.com
Sales – http://www.cypress.com/aboutus/sales_locations.cfm
Technical Support – http://www.cypress.com/support/login.cfm
7.1
Revision History
Document Title:
CY8C21234, CY8C21334, CY8C21434, CY8C21534, and CY8C21634 PSoC Mixed-Signal Array Final Data Sheet
Document Number: 38-12025
Originof
Change
Revision ECN # Issue Date
Description of Change
New silicon and document (Revision **).
**
5/19/2004
HMT
SFV
227340
Updated Overview and Electrical Spec. chapters, along with revisions to the 24-pin pinout part.
Revised the register mapping tables. Added a SSOP 28-pin part.
*A
235992 See ECN
Changed title to include all part #s. Changed 28-pin SSOP from CY8C21434 to CY8C21534.
Changed pin 9 on the 28-pin SSOP from SMP pin to Vss pin. Added SMP block to architecture
diagram. Update Electrical Specifications. Added another 32-pin MLF part: CY8C21634.
*B
*C
248572 See ECN
277832 See ECN
SFV
HMT
Verify data sheet standards from SFV memo. Add Analog Input Mux to applicable pin outs.
Update PSoC Characteristics table. Update diagrams and specs. Final.
*D
*E
285293 See ECN
301739 See ECN
329104 See ECN
HMT
HMT
HMT
Update 2.7V DC GPIO spec. Add Reflow Peak Temp. table.
DC Chip-Level Specification changes. Update links to new CY.com Portal.
Re-add pinout ISSP notation. Fix TMP register names. Clarify ADC feature. Update Electrical
Specifications. Update Reflow Peak Temp. table. Add 32 MLF E-PAD dimensions. Add ThetaJC to
Thermal Impedance table. Fix 20-pin package order number. Add CY logo. Update CY copyright.
*F
352736 See ECN
HMT
Add new color and logo. Add URL to preferred dimensions for mounting MLF packages. Update
Transmitter and Receiver AC Digital Block Electrical Specifications.
*G
*H
*I
390152 See ECN
413404 See ECN
430185 See ECN
HMT
HMT
HMT
Clarify MLF thermal pad connection info. Replace 16-pin 300-MIL SOIC with correct 150-MIL.
Update 32-pin QFN E-Pad dimensions and rev. *A. Update CY branding and QFN convention.
Add new 32-pin 5x5 mm 0.60 thickness QFN package and diagram, CY8C21434-24LKXI. Update
thermal resistance data. Add 56-pin SSOP on-chip debug non-production part, CY8C21001-
24PVXI. Update typical and recommended Storage Temperature per industrial specs. Update
copyright and trademarks.
*J
677717 See ECN
HMT
Add CapSense SNR requirement reference. Add new Dev. Tool section. Add CY8C20x34 to
PSoC Device Characteristics table. Add Low Power Comparator (LPC) AC/DC electrical spec.
tables. Update rev. of 32-Lead (5x5 mm 0.60 MAX) QFN package diagram.
*K
Distribution: External/Public
Posting: None
January 12, 2007
© Cypress Semiconductor Corp. 2004-2007 — Document No. 38-12025 Rev. *K
41
[+] Feedback
CY8C21x34 Final Data Sheet
7. Sales and Service Information
7.2
Copyrights and Code Protection
Copyrights
© Cypress Semiconductor Corp. 2004-2007. All rights reserved. PSoC Designer™, Programmable System-on-Chip™, and PSoC Express™ are trademarks and PSoC®
is a registered trademark of Cypress Semiconductor Corp. All other trademarks or registered trademarks referenced herein are property of the respective corporations.
The information contained herein is subject to change without notice. Cypress Semiconductor assumes no responsibility for the use of any circuitry other than circuitry
embodied in a Cypress Semiconductor product. Nor does it convey or imply any license under patent or other rights. Cypress Semiconductor does not authorize its prod-
ucts for use as critical components in life-support systems where a malfunction or failure may reasonably be expected to result in significant injury to the user. The inclu-
sion of Cypress Semiconductor products in life-support systems application implies that the manufacturer assumes all risk of such use and in doing so indemnifies
Cypress Semiconductor against all charges. Cypress Semiconductor products are not warranted nor intended to be used for medical, life-support, life-saving, critical con-
trol or safety applications, unless pursuant to an express written agreement with Cypress Semiconductor.
Flash Code Protection Note the following details of the Flash code protection features on Cypress Semiconductor PSoC devices.
Cypress Semiconductor products meet the specifications contained in their particular data sheets. Cypress Semiconductor believes that its PSoC family of products is one
of the most secure families of its kind on the market today, regardless of how they are used. There may be methods, unknown to Cypress Semiconductor, that can breach
the code protection features. Any of these methods, to our knowledge, would be dishonest and possibly illegal. Neither Cypress Semiconductor nor any other semicon-
ductor manufacturer can guarantee the security of their code. Code protection does not mean that we are guaranteeing the product as "unbreakable."
Cypress Semiconductor is willing to work with the customer who is concerned about the integrity of their code. Code protection is constantly evolving. We at Cypress
Semiconductor are committed to continuously improving the code protection features of our products.
January 12, 2007
Document No. 38-12025 Rev. *K
42
[+] Feedback
相关型号:
![](http://pdffile.icpdf.com/pdf2/p00284/img/page/CY8C21434-24_1697182_files/CY8C21434-24_1697182_1.jpg)
![](http://pdffile.icpdf.com/pdf2/p00284/img/page/CY8C21434-24_1697182_files/CY8C21434-24_1697182_2.jpg)
CY8C21434-24LFXIT
MULTIFUNCTION PERIPHERAL, QCC32, 5 X 5 MM, 0.93 MM HEIGHT, LEAD FREE, MO-220, QFN-32
ROCHESTER
©2020 ICPDF网 联系我们和版权申明