VPF-S500-48R [CUI]
Switching Power Supply; 开关电源型号: | VPF-S500-48R |
厂家: | CUI INC |
描述: | Switching Power Supply |
文件: | 总5页 (文件大小:308K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
1 / 5
VPF-S500 Switching Power Supply
Rev. 12-2006
Features
·Built-in active PFC function
·Short Circuit, overload, over voltage,
over temperature protected
·Current Sharing (Available)
·Current Monitoring
·Power Good Signal
·Built-in Remote Inhibit
·Built-in Remote Sense
·Extended temperature range: -40 ~ +75 ºC
available
7, 8
Preset
Voltage
3.3V
5V
Output Current
Ripple & Noise
1
2, 3, 4
5, 6
7
Model
Output
Minimum
0 A
Maximum
80 A
Max. Power
264 W
Regulation
(Vpp)
50 mV
50 mV
1%
VPF-S500-03R(I)
VPF-S500-05R(I)
VPF-S500-12R(I)
VPF-S500-16R(I)
VPF-S500-24R(I)
VPF-S500-36R(I)
VPF-S500-48R(I)
2 - 3.3 V
5 - 6 V
+/- 1%
+/- 1%
+/- 1%
+/- 1%
+/- 1%
+/- 1%
+/- 1%
0 A
80 A
400 W
12V
12 - 15 V
16 - 21 V
22 - 30 V
31 - 47 V
48 - 56 V
0 A
41.67 A
31.25 A
22.73 A
16.13 A
10.42 A
500 W
16V
0 A
500 W
1%
24V
0 A
500 W
1%
36V
0 A
500 W
1%
48V
0 A
500 W
1%
Notes:
1 Adding “I” Indicates Current sharing model.
2 Customer must specify output voltage.
3 Output is fully isolated.
4 Output voltage is measured at output power connector.
5 Provides peak power of 900 W within 500 µS for all models. For longer duty duration please contact us.
6 Must use external forced airflow min. 30 CFM to achieve maximum power.
7 1% minimum load is required to maintain the ripple and regulation.
8 Ripple and noise is measured from 10 KHz to 20 MHz at output terminals with a 0.1 µF ceramic capacitor and
a 22 µF electrolytic capacitor in parallel.
V-Infinity, LLC, 20050 SW 112th Ave., Tualatin, OR 97062
www.v-infinity.com
1-866-372-1258
2 / 5
VPF-S500 Switching Power Supply
Rev. 12-2006
Input
Parameter
Conditions/Description
Min
47
Nom
Max
Units
Hz
Input Frequency
Input Voltage
Input Current
Inrush Current
Power Factor
63
264
8
90
VAC
A
At 90-264 VAC
Peak measured at 230 VAC at full load, cold start
Active power factor correction meets EN61000-3-2 class D
70
A
Output
Parameter
Conditions/Description
Min
Nom
Max
Units
Transient response Output voltage returns to within 1% in less than
2.5 mS for a 50% load change. Peak
transient does not exceed 5%.
Overshoot
Efficiency
Turn-on and turn-off overshoot shall not exceed
5% over nominal voltage.
Measured at 230 V and full load
12 V model:
80%
82%
All other models:
Turn on delay
Hold up time
Adjustability
Remote sense
At 120 VAC
1
second
mS
At 120 VAC and 80% of rated maximim load
Adjustable with built-in trim pot.
20
+/- 5%
Designated as RS+ and RS- on the CN3. Total voltage compensation for cable losses with
respect to the main output. (NOT available for current sharing models.)
Designated as RSW on the CN3. Requires a low signal to inhibit the output.
Green - the power supply is operating normally.
Remote Inhibit
LED display
(LED 1)
Orange - when any protection occurs or when Remote Inhibit is in effect.
Designated as PG on the CN3. This signal
Power Good
goes high 100-500 mS after the output reaches regulation.
It goes low at least 1 mS before loss of regulation.
Current Sharing
Current Monitor
Designated as CSH on (CN3), use in parallel for forced current sharing function.
Accuracy of shared current with up to 4 parallel units is within 10% at full load.
Disignated as CMN on (CN3) for current sense purpose. CMN is a 0.5 to 3VDC output
voltage to represent a linear 0% to 100% output current.
Protection Circuit
Parameter
Conditions/Description
Input Fuse
Built-in ac fuse. A blown fuse usually indicates permanent
damage to the power supply serviceable by factory only.
Power supply shuts down when ac input is under
Input under-voltage
Overload
80 VAC. When ac line reappears over 86 +/- 5 VAC,
the power supply restarts automatically.
Current limiting starts at 110-140% of the rated output current and
recovers automatically.
Short circuit
Short circuit can be continuous. Recovers automatically upon removal of short.
Output is protected agaist overvoltage. Unit shuts down and latches
when voltage at output terminals exceeds 130%. AC input needs to be
reset to restart the power supply.
Output Over-voltage
Over temp.
Power supply shuts down when temperature is in excess of 85 ºC. Auto recovery.
V-Infinity, LLC, 20050 SW 112th Ave., Tualatin, OR 97062
www.v-infinity.com
1-866-372-1258
3 / 5
VPF-S500 Switching Power Supply
Rev. 12-2006
General and Safety
Parameter
Conditions/Description
Min
Nom
Max
Units
Operating temp.
Derates linearly from 100% load at 50 ºC to 50%
load at 70 ºC.
0
50
ºC
Optional operating
temp.
Derates linearly from 100% load at 50 ºC to 37.5%
load at 75ºC.
-40
75
ºC
Storage temp.
Optional storage
temp.
-20
-40
85
85
ºC
ºC
Operating humid.
Storage humid.
EMI
Non-condensing
Non-condensing
5%
5%
90%
95%
RH
RH
Pass FCC Part 15 Subject J Class B, CISPR 22 class B, CE Mark
Safety
UL60950-1 (E222889), CSA C22.2 No. 950-95, TUV EN60950 and CB
Leakage Current
Isolation Voltage
(HI-POT)
at 264 VAC
3.5
0.1
mA
Applied for 3 seconds
Primary to secondary:
3000
1500
1500
VAC
VAC
VAC
Ohm
Primary to transformer core:
Primary to earth ground:
Grounding Test
Allowable resistance measured when 25 A current is
applied from the ground pin of the three prong plug
to the farthest earthed connection point.
Standard warranty length
Warranty
MTBF
2
8
years
hours
hours
According to MIL-HDBK-217 at 30 ºC
Full load, at 45 +/- 5 ºC, 230 VAC. Burn-in for
up to 8 hours in early productions. Time
reduced gradually as product matures.
150,000
1
Burn-in
Note: Customer must specify extended temperature on PO.
Mechanical
Parameter
Conditions/Description
Min
Nom
Max
Units
grams
inches
Weight
1450
Enclosure
Mounting holes
8.00(L) x 4.33(W) x 2.56(H)
Two sets of 8 threaded mounting holes available on the enclosure
B: 6-32, maximum insertion depth of 0.2 inches.
C: M4, maximum insertion depth of 0.2 inches.
Input Connector - (CN1)
Parameter
Conditions/Description
AC input (Option 1) Molex Part No. 26-48-1201 or similar (5 pin).
Suggested mating plug: Molex Part No. 09-91-0500 or equivalent (5 pin, 3 used)
AC Input (Option 2) Howder Terminal block Part No. HD-121-3P (3 pin, M3 Screw) 9.5mm spacing
Suggested mating connector: Molex 19198-0045 or similar
Note: Input connector needs to be specified on the PO.
V-Infinity, LLC, 20050 SW 112th Ave., Tualatin, OR 97062
www.v-infinity.com
1-866-372-1258
4 / 5
VPF-S500 Switching Power Supply
Rev. 12-2006
Output Connector - (CN2)
Conditions/Description
Parameter
Output (Option 1)
Molex Part No. 26-48-1201 or similar.(20 pin)
Output pin assignment, VO+ (Pins 1-10), VO- (Pins 11-20)
Suggested mating connector: Molex Part No. 09-91-2000, contact:08-50-0106 or similar.
Howder Terminal block Part No. HD-121-8P (8 pin, M3.5 Screw) 9.5mm spacing
Output pin assignment, VO+ (Pins 1-4), VO- (Pins 5-8)
Output (Option 2)
Suggested mating connector: Molex 19198-0045 or similar.
Note: Output connector needs to be specified on the PO.
Logic Connector - (CN3)
Parameter
Conditions/Description
Logic
JS B7B-XH-A
Suggested mating connector: JST XHP-7 or equivalent , Contact: SXH-001T-P0.6.
1. CMN - Current Monitoring
Pin Assignments:
2. CSH - Current Sharing
3. RTN - Return / Output Ground
4. PG - Power Good Signal
5. RSW - (Remote On-Off / Remote Inhibit)
6. RS(-) - Remote Sense
7. RS(+) - Remote Sense
Fan
JST B2B-XH-A
Suggested mating connector: JST XHP-2 or equivalent, Contact: SXH-001T-P0.6.
V-Infinity, LLC, 20050 SW 112th Ave., Tualatin, OR 97062
www.v-infinity.com
1-866-372-1258
5 / 5
VPF-S500 Switching Power Supply
Rev. 12-2006
V-Infinity, LLC, 20050 SW 112th Ave., Tualatin, OR 97062
www.v-infinity.com
1-866-372-1258
相关型号:
©2020 ICPDF网 联系我们和版权申明