SMRT28515T [CRANE]
Built in MIL-STD-461 EMI filter Output trim from 51% to 124% of nominal; 内置的MIL -STD- 461的EMI滤波器输出调整从51％到标称124％
| 型号： | SMRT28515T |
| 厂家： | 
Crane Aerospace & Electronics. |
| 描述： | Built in MIL-STD-461 EMI filter Output trim from 51% to 124% of nominal |
| 文件： | 总19页 (文件大小：800K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
Crane Aerospace & Electronics Power Solutions
sMrt28 singlꢂ, Dꢀꢄl ꢄnd tꢃiplꢂ spꢄꢇꢂ Dc/Dc convꢂꢃꢁꢂꢃꢈ
28 VOLt Iꢆꢅut – 35 Watt – sꢅace quaLIFIeD
Features
Bꢀilꢁ in MIL-stD-461 eMI filꢁꢂꢃ
Oꢀꢁpꢀꢁ ꢁꢃim fꢃom 51% ꢁo 124% of nominꢄl
•ꢀ Operating temperature -55° to +125°C
•ꢀ Qualified to MIL-PRF-38534 Class H and K
•ꢀ Radiation hardness assurance (RHA) to
level F 300 kRad(Si)
•ꢀ Input voltage range 19 to 56 VDC
•ꢀ Transient protection 80 V for 100 ms
•ꢀ Fully isolated, 5 port isolation
•ꢀ Dual magnetic feedback
•ꢀ Fixed high frequency switching
•ꢀ Remote sense
•ꢀ Inhibit function
•ꢀ Synchronization input
MODELS
VDC Ou t p u t
•ꢀ Indefinite short circuit protection
•ꢀ Radiation tolerant to
SIꢀꢁLE
3.3
5
DUAL
±5
±12
±15
- 1 x 1012 protons/cm2 neutron or proton fluence
- 1011 rad(Si)/sec dose rate
8.7
12
15
- 3 x 105 rad(Si) total dose
- SEE - LET to 80 MeV cm2/mg
TRIPLE
+3.3 & ±12
+3.3 & ±15
+5 & ±7
•ꢀ Meets MIL-STD-704A transient standards
+5 & ±12
+5 & ±15
DescrIꢅtIOꢆ
A minimum load of 2% of full load should be used on outputs at
TID of 100 kRad(Si) or greater to ensure tight regulation over the
full input range. The converter should not be inhibited or oper-
ated below 19 Vin above 5x104 rad(Si) total dose.
The SMRT28 Series™ of DC/DC converters offers up to 35
watts of power in a radiation tolerant design. The low profile
SMRT28 converters are manufactured in Interpoint’s fully certi-
fied and qualified MIL-PRF-38534 production facility and pack-
aged in hermetically sealed steel cases. They are ideal for use in
programs requiring high reliability, small size, and high levels of
radiation hardening assurance.
Two independent feedback loops are used to regulate the dual
and triple outputs, one feedback loop regulates the two-phased
single output. Each set of outputs is electrically isolated from the
other and from the input. This product configuration eliminates
cross regulation effects between output sets.
The SMRT28 converters are switching regulators which use a
two-phase, phase shifted flyback design with a nominal switching
frequency of 300 kHz. Close regulation is maintained with
advanced constant frequency pulse width modulation design
techniques. The SMRT28’s feed-forward compensation and
discontinuous topologies provide high levels (80 dB peak) of
input-to-output ripple rejection.
Configurations:
•ꢀSingleꢀOutput:ꢀOneꢀtwo-phaseꢀsingleꢀoutput
•ꢀDualꢀOutput:ꢀTwoꢀsingle-phaseꢀsingleꢀoutputs
•ꢀTripleꢀOutput:ꢀOneꢀsingle-phaseꢀindependentꢀ
Main output and one single-phase dual output.
(± Auxiliary output)
Crane Aerospace & Electronics
Page 1 of 19
Electronics ꢁroup (Interpoint Brand)
POꢀBoxꢀ97005ꢀꢀ•ꢀꢀRedmondꢀWAꢀ98073-9705
425.882.3100ꢀꢀꢀ•ꢀꢀꢀpower@crane-eg.com
www.interpoint.com
SMRT28 Rev E - 20100216
The information in this document is a derivative of a document cleared
by the Department of Defense (DoD) Office of Security Review (OSR) for
public release. OSR case number 09-S-1960 dated June 22, 2009.
Crane Aerospace & Electronics Power Solutions
sMrt28 singlꢂ, Dꢀꢄl ꢄnd tꢃiplꢂ spꢄꢇꢂ Dc/Dc convꢂꢃꢁꢂꢃꢈ
28 VOLt Iꢆꢅut – 35 Watt – sꢅace quaLIFIeD
At the highest dose rate (1011 rad(Si)/sec dose rate) there will be
an upset resulting in a dip in the voltage. This is non-destructive
to the unit. The converter will operate through the upset.
un D e r V O l t a g e lO C k O u t
The converters have an undervoltage lockout that will allow
power conversion at approximately 17 volts on a rising input
voltage and a conversion shut-down on a falling voltage at
approximately 14.5 volts.
SC r e e n I n g
SMRT28 converters offer the following screening options:
Space Prototype (O), Class H, or Class K. Radiation tolerant to
Radiation Hardness Assurance (RHA) levels of “-” (O), “P”, “R” or
“F”, per MIL-PRF-38534. Interpoint model numbers use an “O” in
the RHA designator position to indicate the “-” (dash) Radiation
Hardness Assurance level of MIL-PRF-38534, which is defined as
“no RHA”. See Screening Tables 1, 2 and 3 for more information.
In h I b I t Fu n C t I O n
The SMRT28 Series incorporates an inhibit terminal that can be
used to disable internal switching. It is not recommended to tie
the Inhibit pin of an SMRT28 directly to the Inhibit pin of another
converterꢀasꢀtheꢀSMRT28ꢀInhibitꢀpinꢀcanꢀsinkꢀcurrent.ꢀWhenꢀ
pulling multiple inhibit signals low a separate interface is recom-
mended for each SMRT28. The converter is inhibited when the
inhibit pin is pulled low (0.4 V). In the inhibit mode the inhibit pin
current requirement is less than ~2 mA. The converter resumes
normalꢀoperationꢀwhenꢀaꢀhighꢀ(≥ꢀ2.4ꢀV)ꢀsignalꢀorꢀopenꢀcircuitꢀisꢀ
applied to the inhibit pin. The open circuit voltage of the inhibit is
5 to 6 volts. Although open circuit is the preferred method for the
enabled state, up to 10 volts may be applied to the inhibit pin.
emI
The SMRT28 has a built-in EMI input filter which brings the
conducted emissions into compliance with both methods of
MIL-STD-461, revisions C-CE03 and D-/E-/F-CE102.
Se n S e
Tight load regulation is maintained via wide bandwidth magnetic
feedback and through the use of remote sense on single output
models and one output (Output “A”) of the dual units. The sense
feature can be used to adjust the output voltage by connecting a
resistor between the positive sense line and the positive output.
Sy n C h r O n I z a t I O n
The Sync Input is isolated which allows Sync Return to be tied to
the primary side, secondary side, or float with respect to all inputs
and outputs. Input current into this pin is limited by a series 1 k
ohm resistance.
Se n S e Ad j u S t In S t r u c t I o n S f o r
ou t p u t A o n du A l Mo d e l S
Ad j u S t up on l y
(sꢂꢂ ꢁꢃim ꢁꢄblꢂꢈ on pꢄgꢂ 4 foꢃ moꢃꢂ opꢁionꢈ)
Ou t p u t VO l t a g e tr I m
The output voltage of each set can be trimmed from 51% to
125% of nominal (varies by model, see trim instructions on page
4). The following are “sets” of voltages in relation to trim:
•ꢀTripleꢀoutputꢀmodels:ꢀMainꢀoutputꢀisꢀoneꢀset,ꢀtheꢀdualꢀoutputsꢀ
are another set.
•ꢀDualꢀoutputs:ꢀEachꢀoutputꢀisꢀaꢀ“set.”
One set can be trimmed using the trim pin, the other set can
be trimmed (up only) using the positive sense pin.
•ꢀSingle:ꢀOneꢀset
Vout - Vnom
Vmax - Vout
RaD j u S t = 240
(
)
Vout = desired output voltage
Vnom = nominal unadjusted output voltage
Vmax = maximum achievable output voltage
5V Vmax = 6.0 V
12V Vmax = 14.68 V
15V Vmax = 18.36V
ra D I a t I O n tO l e r a n C e
The SMRT28 DC/DC converters are designed to provide contin-
uous normal operation through radiation levels associated with
space missions and in tactical and strategic military environ-
ments. The converters will operate normally in radiation environ-
ments with up to 1 x 1012 neutrons per square centimeter neutron
fluence, 1011 rad(Si) per second dose rate, and 3x105 rad(Si)
total dose.
ꢀote: RADJUST should be connected
between Sense A (pin 8) and Vout A (pin 11).
These levels of radiation tolerance make the SMRT28 converters
suitable for electronics in programs where operation in high radia-
tion environments is required.
www.interpoint.com
Page 2 of 19
SMRT28 Rev E - 20100216
Crane Aerospace & Electronics Power Solutions
sMrt28 singlꢂ, Dꢀꢄl ꢄnd tꢃiplꢂ spꢄꢇꢂ Dc/Dc convꢂꢃꢁꢂꢃꢈ
28 VOLt Iꢆꢅut – 35 Watt – sꢅace quaLIFIeD
convꢂꢃꢈion Fꢃꢂꢉꢀꢂnꢇy
Operating COnditiOns and CharaCteristiCs
•ꢀ 300 kHz typ 270 kHz min, 330 kHz max
Inpꢀꢁ Volꢁꢄgꢂ rꢄngꢂ
rꢄdiꢄꢁion (will opꢂꢃꢄꢁꢂ ꢁhꢃoꢀgh)
•ꢀ 1x1012 neutrons/cm2 neutron or proton fluence
•ꢀ Radiation dose rate 1011 rad(Si) /sec
•ꢀ Total dose up to 300 kRad(Si)
•ꢀ 19 to 56 VDC continuous
•ꢀ 80 V for 100 ms transient
Oꢀꢁpꢀꢁ ꢅowꢂꢃ
•ꢀ Up to 35 watts depending on model
•ꢀ SEE - LET to 80 MeV cm2/mg
Lꢂꢄd soldꢂꢃing tꢂmpꢂꢃꢄꢁꢀꢃꢂ (10 ꢈꢂꢇ pꢂꢃ pin)
•ꢀ 300°C
synC and inhibit
sꢁoꢃꢄgꢂ tꢂmpꢂꢃꢄꢁꢀꢃꢂ rꢄngꢂ (cꢄꢈꢂ)
•ꢀ -65°C to +150°C
synꢇ
•ꢀInput frequency 270-330 kHz
•ꢀ Duty cycle 20% min, 80% max
•ꢀ 2.5 V p-p minimum amplitude
•ꢀ 10 V p-p maximum amplitude
•ꢀ Sync circuit is floating and isolated
•ꢀ If sync is used at lower end of the range, full load
operation is not guaranteed.
cꢄꢈꢂ Opꢂꢃꢄꢁing tꢂmpꢂꢃꢄꢁꢀꢃꢂ (tꢇ)
•ꢀ -55°C to +125°C full power
•ꢀ -55°C to +135°C absolute
Dꢂꢃꢄꢁing Oꢀꢁpꢀꢁ ꢅowꢂꢃ/cꢀꢃꢃꢂnꢁ
•ꢀ Linearly from 100% at 125°C to 0% at 135°C
ꢅowꢂꢃ Diꢈꢈipꢄꢁion (ꢅd)
•ꢀꢀ20ꢀtoꢀ31ꢀW
Inhibiꢁ
•ꢀ Active low (output disabled)
‣IꢀH referenced to input common
‣Active low, pulled to 0.4 V or lower
‣Inhibit pin current < 2mA
•ꢀ Active high (output enabled)
‣High >2.4V
Oꢀꢁpꢀꢁ Volꢁꢄgꢂ tꢂmpꢂꢃꢄꢁꢀꢃꢂ coꢂffiꢇiꢂnꢁ
•ꢀ 100 ppm/°C max
cꢀꢃꢃꢂnꢁ Limiꢁ
•ꢀ 125% of full load typical
Iꢈolꢄꢁion ꢄꢁ 25°c
•ꢀ 100 megohm minimum at 500 V
‣ꢀot to exceed 10V
‣Open pin voltage 5 to 6 volts
aꢀdio rꢂjꢂꢇꢁion
•ꢀ 50 dB typical
meChaniCal and envirOnmental
sizꢂ (mꢄximꢀm)
sꢇꢃꢂꢂning
•ꢀ2.705 x 2.205 x 0.400 inches (68.71 x 56.01 x 10.16 mm)
‣See case S for dimensions.
Space Prototype, Class H, or Class K are radiation tolerant
to Radiation Hardness Assurance (RHA) levels of “-” (O), “P”,
“R”, or “F” per MIL-PRF-38534. Interpoint model numbers use
an “O” in the RHA designator position to indicate the “-” (dash)
Radiation Hardness Assurance level of MIL-PRF-38534, which is
defined as “no RHA”.
Wꢂighꢁ (mꢄximꢀm)
•ꢀ 100 grams maximum
See Screening Tables 1, 2 and 3 for more information. Available
configurations: OO, HP, HR, KP, KR, KF
www.interpoint.com
Page 3 of 19
SMRT28 Rev E - 20100216
Crane Aerospace & Electronics Power Solutions
sMrt28 singlꢂ, Dꢀꢄl ꢄnd tꢃiplꢂ spꢄꢇꢂ Dc/Dc convꢂꢃꢁꢂꢃꢈ
28 VOLt Iꢆꢅut – 35 Watt – sꢅace quaLIFIeD
trIM taBLes
tr I m up
tr I m D O w n
Singles
Singles
Rt r I m should be connected between the tꢃim pin and ꢅoꢈiꢁivꢂ sꢂnꢈꢂ pin.
Rt r I m should be connected between the tꢃim pin and sꢂnꢈꢂ rꢂꢁꢀꢃn pin.
Duals
Duals
Rt r I m should be connected between the tꢃim B pin and ꢅoꢈiꢁivꢂ Voꢀꢁ B
pin. This only trims output B, output A can use the sense pin to trim up
only. See page 2 for instructions on trimming up output A.
Rt r I m should be connected between the tꢃim B pin and Voꢀꢁ B rꢂꢁꢀꢃn pin.
This only trims output B, output A can use the sense pin to trim up only.
Triples
Triples
Rt r I m should be connected between the tꢃim a pin and Voꢀꢁ a rꢂꢁꢀꢃn pin
Rt r I m should be connected between the tꢃim a pin and ꢅoꢈiꢁivꢂ Voꢀꢁ
to adjust the Main outputs.
a pin to adjust the Main output.
Rt r I m should be connected between the tꢃim B pin and Voꢀꢁ B rꢂꢁꢀꢃn pin
Rt r I m should be connected between the tꢃim B pin and ꢅoꢈiꢁivꢂ Voꢀꢁ
to adjust the Auxiliary outputs.
B pin to adjust the Auxiliary outputs.
Vmax - Vout
Vout - Vnom
Rt r I m = K (
)
Vout - Vmin
Vnom - Vout
Rt r I m = K (
)
Vout = Desired Voltage; K/Vmax/Vnom from table below.
Vout = Desired Voltage; K/Vmin/Vnom from table below.
VꢀOM
K
VMAX
% OF VꢀOM
VꢀOM
K
VMIꢀ
% OF VꢀOM
3.3
5.0
7.0
8.7
12
3000
3000
5300
5300
5300
5300
3.70
6.26
112
125
118
149
122
124
3.3
5.0
7.0
8.7
12
3500
4520
3.18
4.16
5.47
6.13
7.05
7.65
96
83
78
70
58
51
8.27
8020
10.46
14.69
18.54
9040
11030
12900
15
15
ꢀote: Do not exceed maximum power rating when trimming up.
ꢀote: Do not exceed maximum current rating when trimming down,
1
2
3
4
5
14
13
1
2
3
4
5
14
13
Trim 12
11
Trim 12
SMRT Single
SMRT Single
11
10
9
10
Sense Return
9
8
Sense
8
1
2
3
4
5
Vout B Return 14
13
Trim B 12
1
2
3
4
5
14
SMRT Dual
11
10
9
Vout B 13
Trim B 12
SMRT Dual
11
10
9
8
8
1
2
3
4
5
14
Vout A 13
Trim A 12
1
2
3
4
5
14
Vout A Return 13
Trim A 12
SMRT Triple
11
10
9
+Vout B
SMRT Triple
11
Vout B Return 10
9
Trim B
8
Trim B
8
FI g u r e 1: tr I m DO w n DI a g r a m S
FI g u r e 2: tr I m up DI a g r a m S
www.interpoint.com
Page 4 of 19
SMRT28 Rev E - 20100216
Crane Aerospace & Electronics Power Solutions
sMrt28 singlꢂ, Dꢀꢄl ꢄnd tꢃiplꢂ spꢄꢇꢂ Dc/Dc convꢂꢃꢁꢂꢃꢈ
28 VOLt Iꢆꢅut – 35 Watt – sꢅace quaLIFIeD
ꢅIꢆ Out
ꢅin
1
singlꢂ Oꢀꢁpꢀꢁ
Vin
Dꢀꢄl Oꢀꢁpꢀꢁ
Vin
tꢃiplꢂ Oꢀꢁpꢀꢁ
Vin
2
Vin Return
Inhibit
Vin Return
Inhibit
Vin Return
Inhibit
3
4
Sync In
Sync In
Sync In
5
Sync Return
Sense
Sync Return
Sense A
Sync Return
Trim B
8
9
Sense Return
Vout A Return
Vout A
Sense A Return
Vout A Return
Vout A
Vout B ꢀegative
Vout B Return
Vout B Positive
Trim A
10
11
12
13
14
Trim
Trim B
Vout A
Vout B
Vout A
Vout A Return
Vout B Return
Vout A Return
1
2
3
4
5
14
13
12
11
10
9
TOP VIEW
See case S for dimensions.
8
FI g u r e 3: pIn Ou t
ꢅIꢆs ꢆOt Iꢆ use
Inhibit: single, dual and triple
Sync In
Leave unconnected
Connect to Sync Return
Sense Lines
Must be connected to appropriate outputs
Leave unconnected
Trim (all)
www.interpoint.com
Page 5 of 19
SMRT28 Rev E - 20100216
Crane Aerospace & Electronics Power Solutions
sMrt28 singlꢂ, Dꢀꢄl ꢄnd tꢃiplꢂ spꢄꢇꢂ Dc/Dc convꢂꢃꢁꢂꢃꢈ
28 VOLt Iꢆꢅut – 35 Watt – sꢅace quaLIFIeD
MODeL ꢆuMBerIꢆꢊ keꢋ
sMD ꢆuMBers
St A n d A r d MI c r o c I r c u I t
dr A w I n g (SMd)
SMrt28 SIMIlAr pA r t
SMRT 28 515 T / K
F
Base Model
Input Voltage
Output Voltage
5962F0622001KXC
5962F0622101KXC
5962F0821001KXC
5962F0622201KXC
5962F0622301KXC
5962F0720201KXC
5962F0622401KXC
5962F0821101KXC
5962F0821201KXC
5962F0622501KXC
5962F0622601KXC
SMRT283R3S/KF
SMRT2805S/KF
SMRT2812S/KF
SMRT2815S/KF
SMRT2805D/KF
SMRT2812D/KF
SMRT2815D/KF
SMRT283R312T/KF
SMRT283R315T/KF
SMRT28512T/KF
SMRT28515T/KF
(single or dual Vout for single or dual models
main and aux. Vout for triple models)
Number of Outputs
(S=single, D=dual, T=triple)
Screening
Radiation Hardness
Assurance (RHA)
The SMD number shown is for Class K screening and
Radiation Hardness Assurance (RHA) level F. See the
SMD for the numbers for other screening and radiation
levels. For exact specifications for an SMD product, refer
to the SMD drawing. SMDs can be downloaded from:
http://www.dscc.dla.mil/programs/smcr
MODeL seLectIOꢆ
on t h e l I n e S b e l o w , e n t e r o n e S e l e c t I o n f r o M e A c h c A t e g o r y to d e t e r M I n e t h e M o d e l n u M b e r .
_______
sMrt28
/
cateꢊOrꢋ
seLectIOꢆ
1
2
3
4
Base Model and
Input Voltage
Output Voltage
ꢀumber of Outputs
Screening
RHA
3r3, 05, 12, 15
05, 12, 15
s
D
t
O
H
k
O
ꢅ
r
F
SMRT28 is the only
available selection
3r312, 3r315, 512, 515
ꢀotes:
1. Output Voltage: An R indicates a decimal point. 3R3 is 3.3 volts out. The 3R3 output voltage is only available in single and triple output models. The 3R312
and 3R315 triple output converters are +3.3 volt main and ±12 or ±15 volt auxiliaries. 512 and 515 triple output converters are +5 volt main and ±12 or ±15 volt
auxiliaries.
2. ꢀumber of Outputs: S is a single output, D is a dual output, and T is a triple output
3. Screening: A screening level of O is a Space Prototype and is only used with RHA O. See Screening Tables 2 and 3 for more information.
4. RHA: Interpoint model numbers use an “O” in the RHA designator position to indicate the “-” (dash) Radiation Hardness Assurance level of MIL-PRF-38534,
which is defined as “no RHA.” RHA O is only available with Screening level O. See Screening Table 3 for more information.
www.interpoint.com
Page 6 of 19
SMRT28 Rev E - 20100216
Crane Aerospace & Electronics Power Solutions
sMrt28 singlꢂ, Dꢀꢄl ꢄnd tꢃiplꢂ spꢄꢇꢂ Dc/Dc convꢂꢃꢁꢂꢃꢈ
28 VOLt Iꢆꢅut – 35 Watt – sꢅace quaLIFIeD
Electrical Characteristics: -55°C to +125°C T , 28 VDC Vin, 100% load, unless otherwise specified.
C
SIꢀꢁLE OUTPUT MODELS
SMRT283R3S
SMRT2805S
SMRT288R7S
unItS
parameter
COnDItIOnS
MIꢀ
TYP
3.30
—
MAX
MIꢀ
TYP
5.00
—
MAX
MIꢀ
TYP
8.70
—
MAX
Output VOltage
Output Current
3.23
0
3.37
6.97
23
4.90
0
5.10
6.0
30
8.52
0
8.87
4.0
35
VDC
A
2
2
Output pOwer
V
= 19 tO 56 VDC
0
—
0
—
0
—
W
In
Output rIpple
10 khz - 20 mhz
= 19, 50 VDC
—
—
—
—
—
280
30
—
—
—
—
—
200
30
—
—
—
—
—
200
30
mV p-p
mV
2
lIne regulatIOn
V
5
5
5
In
lOaD regulatIOn
5
40
5
40
5
80
mV
V
= 19, 50
—
90
—
70
—
80
In
1
tOtal regulatIOn
all COnDItIOnS OF
lIne, lOaD, agIng,
temp anD raDIatIOn
V
3.0
—
3.6
4.7
—
5.3
8.3
—
9.1
VDC
Out
Input VOltage
Input Current
COntInuOuS
19
0
28
—
—
—
10
—
—
—
—
—
56
80
19
0
28
—
—
—
10
—
—
—
—
—
56
80
19
0
28
—
—
—
10
—
—
—
—
—
56
80
VDC
V
1
tranSIent 100 ms
InhIbIteD
nO lOaD
—
—
—
60
—
—
—
—
50
—
—
—
66
—
—
—
—
50
—
—
—
72
—
—
—
—
50
mA
110
50
110
50
115
50
3
Input rIpple Current
eFFICIenCy
10 kHz - 20 MHz
mA p-p
%
—
—
—
4, 5
lOaD Fault
POWERꢀDISSIPATION
31
28
25
W
1
reCOVery
25
25
25
ms
5, 6, 7
Step lOaD reSpOnSe
tranSIent
reCOVery
±450
3
±450
3
±450
4
mV pk
ms
1, 5, 6
Step lIne reSpOnSe
19 - 50 - 19 V
In
—
—
—
—
—
—
—
—
±500
4
—
—
—
—
—
—
—
—
±500
4
—
—
—
—
—
—
—
—
±500
4
mV pk
ms
tranSIent
reCOVery
8
Start-up
Delay
nO lOaD anD Full
35
25
60
ms
OVerShOOt
50
50
95
mV pk
1
CapaCItIVe lOaD
unCOnDItIOnally
Stable, Start-up
Delay InCreaSeD
t
= 25°C
—
—
5000
—
—
5000
—
—
5000
µF
C
ꢀotes
1. ꢊꢀꢄꢃꢄnꢁꢂꢂd by dꢂꢈign, noꢁ ꢁꢂꢈꢁꢂd.
2. To maintain tight regulation over the full input voltage range a minimum load of 2% of full load should be used on all outputs.
3. Converters meet MIL-STD-461 specification revisions for conducted emissions C-CE03 and D-/E-/F-CE-102. The actual value of input ripple current is much less, the
limit in the characteristic table is based on measurement resolution..
4. Maximum power dissipation when output is shorted.
5. Recovery time is measured from application of the transient to point at which VOUT is within 1% of VOUT at final value.
6. Transition time >10 µs.
7. Half load to/from full load.
8. Measured from release of inhibit or input voltage step
www.interpoint.com
Page 7 of 19
SMRT28 Rev E - 20100216
Crane Aerospace & Electronics Power Solutions
sMrt28 singlꢂ, Dꢀꢄl ꢄnd tꢃiplꢂ spꢄꢇꢂ Dc/Dc convꢂꢃꢁꢂꢃꢈ
28 VOLt Iꢆꢅut – 35 Watt – sꢅace quaLIFIeD
Electrical Characteristics: -55°C to +125°C T , 28 VDC Vin, 100% load, unless otherwise specified.
C
SIꢀꢁLE OUTPUT MODELS
SMRT2812S
SMRT2815S
unItS
parameter
COnDItIOnS
MIꢀ
TYP
MAX
MIꢀ
TYP
MAX
Output VOltage
Output Current
11.76 12.00 12.24 14.70 15.00 15.30
VDC
A
2
—
0
—
—
—
5
2.92
35
—
0
—
—
—
5
2.33
35
2
Output pOwer
V
= 19 tO 56 VDC
W
In
Output rIpple
10 khz - 20 mhz
—
—
—
—
200
30
—
—
—
—
180
30
mV p-p
mV
2
lIne regulatIOn
V
= 19, 50 VDC
In
lOaD regulatIOn
5
40
5
40
mV
V
= 19, 50 VDC
—
90
—
90
In
1
tOtal regulatIOn
all COnDItIOnS OF
lIne, lOaD, agIng,
temp anD raDIatIOn
V
10.9
—
13.1
14.0
—
16.0
VDC
OUT
Input VOltage
Input Current
COntInuOuS
19
0
28
—
—
—
10
—
—
—
—
—
56
80
19
0
28
—
—
—
10
—
—
—
—
—
56
80
VDC
V
1
tranSIent 100 ms
InhIbIteD
nO lOaD
—
—
—
75
—
—
—
—
50
—
—
—
75
—
—
—
—
50
mA
110
50
110
50
3
Input rIpple Current
eFFICIenCy
10 kHz - 20 MHz
mA p-p
%
—
—
4, 5
lOaD Fault
POWERꢀDISSIPATION
20
20
W
1
reCOVery
25
25
ms
5, 6, 7
Step lOaD reSpOnSe
tranSIent
reCOVery
±575
3
±575
3
mV pk
ms
1, 5, 6
Step lIne reSpOnSe
19 - 50 - 19 V
In
—
—
—
—
—
—
±700
4
—
—
—
—
—
—
±700
4
mV pk
ms
tranSIent
reCOVery
8
Start-up
Delay
nO lOaD anD Full
25
25
ms
OVerShOOt
—
—
—
—
120
—
—
—
—
150
mV pk
µF
1
CapaCItIVe lOaD
unCOnDItIOnally
Stable, Start-up
Delay InCreaSeD
t
= 25°C
5000
5000
C
ꢀotes
1. ꢊꢀꢄꢃꢄnꢁꢂꢂd by dꢂꢈign, noꢁ ꢁꢂꢈꢁꢂd.
2. To maintain tight regulation over the full input voltage range a minimum load of 2% of full load should be used on all outputs.
3. Converters meet MIL-STD-461 specification revisions for conducted emissions C-CE03 and D-/E-/F-CE-102. The actual value of input ripple
current is much less, the limit in the characteristic table is based on measurement resolution..
4. Maximum power dissipation when output is shorted.
5. Recovery time is measured from application of the transient to point at which VOUT is within 1% of VOUT at final value.
6. Transition time >10 µs.
7. Half load to/from full load.
8. Measured from release of inhibit or input voltage step
www.interpoint.com
Page 8 of 19
SMRT28 Rev E - 20100216
Crane Aerospace & Electronics Power Solutions
sMrt28 singlꢂ, Dꢀꢄl ꢄnd tꢃiplꢂ spꢄꢇꢂ Dc/Dc convꢂꢃꢁꢂꢃꢈ
28 VOLt Iꢆꢅut – 35 Watt – sꢅace quaLIFIeD
Electrical Characteristics: -55°C to +125°C T , 28 VDC Vin, 100% load, unless otherwise specified.
C
DUAL OUTPUT MODELS
SMRT2805D
SMRT2812D
SMRT2815D
unItS
parameter
COnDItIOnS
VO u t a
MIꢀ
TYP
5.00
5.00
—
MAX
MIꢀ
TYP
MAX
MIꢀ
TYP
MAX
Output VOltage
Output Current
4.90
4.90
—
5.10
5.10
3.0
11.76 12.00 12.24 14.70 15.00 15.30
11.76 12.00 12.24 14.70 15.00 15.30
VDC
VO u t b
2, 3
VO u t a
—
—
—
—
1.46
1.46
—
—
—
—
1.17
1.17
A
VO u t b
—
—
3.0
2, 3
Output pOwer
VO u t a
VO u t b
0
—
—
—
—
5
15
15
0
—
—
—
5
17.5
17.5
200
25
0
—
—
—
5
17.5
17.5
180
30
W
VIn = 19 tO 56 VDC
0
0
0
Output rIpple
10 khz - 20 mhz
—
—
—
—
200
30
—
—
—
—
—
—
—
—
mV p-p
mV
2
lIne regulatIOn
V
= 19, 50 VDC
Iꢀ
lOaD regulatIOn
40
5
50
5
40
mV
V
= 19, 50 VDC
—
70
—
100
—
70
Iꢀ
1
tOtal regulatIOn
all COnDItIOnS OF
lIne, lOaD, agIng,
temp anD raDIatIOn
V
±4.6
—
±5.4
±10.9
—
±13.1 ±14.0
—
±16.0
VDC
OUT
4
Input VOltage
COntInuOuS
19
0
28
—
—
—
56
80
19
0
28
—
—
—
56
80
19
0
28
—
—
—
56
80
VDC
V
tranSIent 100 ms
4
Input Current
InhIbIteD
—
—
50
—
—
50
—
—
50
mA
nO lOaD
110
110
110
Input rIpple
Current
mA p-p
10 kHz - 20 MHz
—
10
50
—
10
150
—
10
50
4
eFFICIenCy
66
—
—
—
—
—
—
—
—
—
—
28
75
—
—
—
—
—
—
—
—
—
—
20
75
—
—
—
—
—
—
—
—
—
—
20
%
W
5, 6
lOaD Fault
pOwer DISSIpatIOn
1
reCOVery
25
25
25
ms
Step lOaD
reSpOnSe
tranSIent
reCOVery
±450
3
±450
2
±575
3
mV pk
ms
6, 7, 8
Step lIne
reSpOnSe
19 - 50 - 19 V
tranSIent
Iꢀ
—
—
—
—
—
—
—
—
±500
4
—
—
—
—
—
—
—
—
±1000
3
—
—
—
—
—
—
—
—
±700
4
mv pk
ms
1, 6, 7
reCOVery
9
Start-up
Delay
nO lOaD anD Full
25
20
25
ms
OVerShOOt
50
350
150
mV pk
1
CapaCItIVe lOaD
unCOnDItIOnally
Stable, Start-up
Delay InCreaSeD
t
= 25°C
—
—
5000
—
—
5000
—
—
5000
µF
C
ꢀotes
1. ꢊꢀꢄꢃꢄnꢁꢂꢂd by dꢂꢈign, noꢁ ꢁꢂꢈꢁꢂd.
2. The specified maximum current/power is available from each output.
3. To maintain tight regulation over the full input voltage range a minimum load of 2% of full load should be used on all outputs.
4. Converters meet MIL-STD-461 specification revisions for conducted emissions C-CE03 and D-/E-/F-CE-102. The actual value of input ripple current is much less, the
limit in the characteristic table is based on measurement resolution..
5. Maximum power dissipation when output is shorted.
6. Recovery time is measured from application of the transient to point at which VOUT is within 1% of VOUT at final value.
7. Transition time >10 µs.
8. Half load to/from full load.
9. Measured from release of inhibit or input voltage step
www.interpoint.com
Page 9 of 19
SMRT28 Rev E - 20100216
Crane Aerospace & Electronics Power Solutions
sMrt28 singlꢂ, Dꢀꢄl ꢄnd tꢃiplꢂ spꢄꢇꢂ Dc/Dc convꢂꢃꢁꢂꢃꢈ
28 VOLt Iꢆꢅut – 35 Watt – sꢅace quaLIFIeD
Electrical Characteristics: -55°C to +125°C T , 28 VDC Vin, 100% load, unless otherwise specified.
C
TRIPLE OUTPUT MODEL – SMRT283R312T
3.3 (MAIꢀ)
±12 (AUXILIARIES)
unItS
parameter
COnDItIOnS
MIꢀ
3.23
—
TYP
3.30
—
MAX
3.37
—
MIꢀ
TYP
MAX
Output VOltage
MAIꢀ AꢀD POS. AUX
ꢀEꢁ. AUX.
11.76 12.00 12.24
VDC
-11.58 -12.00 -12.42
2, 3
1
Output Current
—
—
—
—
4.5
—
0
±0.63
—
1
A
TOTAL
—
1.25
2, 3
1
Output pOwer
0
—
—
15
—
0
±7.5
—
12
W
V
= 19 tO 56 VDC
TOTAL
—
—
15
Iꢀ
Output rIpple
10 khz - 20 mhz
MAIꢀ AꢀD POS. AUX
ꢀEꢁ. AUX.
—
—
—
—
—
—
—
—
5
200
30
—
—
—
—
—
—
5
150
30
mV p-p
mV
lIne regulatIOn
V
= 19, 50 VDC
—
10
5
70
Iꢀ
lOaD regulatIOn
MAIꢀ AꢀD POS. AUX
40
40
V
= 19, 50 VDC
—
100
—
120
Iꢀ
mV
1
ꢀEꢁ. AUX.
—
—
—
—
—
—
—
—
10
—
300
400
1
V
= 19, 50 VDC
Iꢀ
1
tOtal regulatIOn
all COnDItIOnS OF
lIne, lOaD, agIng,
temp anD raDIatIOn
V
3.0
—
3.6
±10.9
—
±13.1
VDC
%
OUT
1, 4, 5
CrOSS regulatIOn
EFFECT Oꢀ
—
—
—
—
—
—
—
2.5
—
t
= 25°C
ꢀEꢁATIVE AUXILIARY
C
Input VOltage
COntInuOuS
19
28
56
VDC
V
tranSIent 100 ms
nO lOaD
0
—
—
—
80
110
50
—
—
—
—
—
—
—
—
—
Input Current
—
—
mA
InhIbIteD
6
Input rIpple Current
10 kHz - 10 MHz
—
68
—
—
—
—
10
—
—
—
—
—
50
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
mA p-p
%
7
eFFICIenCy
8, 9
lOaD Fault
POWERꢀDISSIPATION
28
—
W
1
reCOVery
25
25
ms
9, 10, 11
Step lOaD reSpOnSe
tranSIent
reCOVery
±450
3
±450
3
mV pk
ms
1, 8, 9
Step lIne reSpOnSe
22 - 35 - 22 V
In
—
—
—
—
—
—
—
0
±500
4
—
—
—
—
—
—
—
0
±750
4
mV pk
ms
tranSIent
reCOVery
11
Start-up
Delay
nO lOaD anD Full
35
25
ms
OVerShOOt
50
120
mV pk
1
CapaCItIVe lOaD
unCOnDItIOnally
Stable, Start-up
Delay InCreaSeD
t
= 25°C
—
—
5000
—
—
1000
µF
C
ꢀotes: See page 15
www.interpoint.com
Page 10 of 19
SMRT28 Rev E - 20100216
Crane Aerospace & Electronics Power Solutions
sMrt28 singlꢂ, Dꢀꢄl ꢄnd tꢃiplꢂ spꢄꢇꢂ Dc/Dc convꢂꢃꢁꢂꢃꢈ
28 VOLt Iꢆꢅut – 35 Watt – sꢅace quaLIFIeD
Electrical Characteristics: -55°C to +125°C T , 28 VDC Vin, 100% load, unless otherwise specified.
C
TRIPLE OUTPUT MODEL – SMRT283R315T
3.3 (MAIꢀ)
TYP
±15 (AUXILIARIES)
unItS
parameter
COnDItIOnS
MIꢀ
3.23
MAX
3.37
MIꢀ
TYP
MAX
Output VOltage
MAIꢀ AꢀD POS. AUX
ꢀEꢁ. AUX.
3.30
14.70 15.00 15.30
VDC
-14.48 -15.00 -15.53
2, 3
1
Output Current
—
—
—
—
4.5
—
0
±0.5
—
0.8
A
TOTAL
TOTAL
—
1.0
2, 3
1
Output pOwer
0
—
—
15
—
0
±7.5
—
12
W
V
= 19 tO 56 VDC
—
—
15
Iꢀ
Output rIpple
10 khz - 20 mhz
MAIꢀ AꢀD POS. AUX
ꢀEꢁ. AUX.
—
—
—
—
200
30
—
—
—
—
—
—
—
—
5
150
30
mV p-p
lIne regulatIOn
mV
V
= 19, 50 VDC
10
5
70
Iꢀ
lOaD regulatIOn
MAIꢀ AꢀD POS. AUX
—
—
—
—
5
40
100
—
40
V
= 19, 50 VDC
—
—
—
—
—
—
120
300
400
Iꢀ
mV
1
ꢀEꢁ. AUX.
1
V
= 19, 50 VDC
—
Iꢀ
1
tOtal regulatIOn
all COnDItIOnS OF
lIne, lOaD, agIng,
temp anD raDIatIOn
V
3.0
—
3.6
±14.0
—
±16.0
VDC
%
OUT
1, 4, 5
CrOSS regulatIOn
EFFECT Oꢀ
—
—
—
—
—
—
—
2.5
—
t
= 25°C
ꢀEꢁATIVE AUXILIARY
C
Input VOltage
COntInuOuS
19
28
56
VDC
V
tranSIent 100 ms
nO lOaD
0
—
—
—
80
110
50
—
—
—
—
—
—
—
—
—
Input Current
—
—
mA
InhIbIteD
6
Input rIpple Current
10 kHz - 10 MHz
—
68
—
—
—
—
10
—
—
—
—
—
50
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
mA p-p
%
7
eFFICIenCy
8, 9
lOaD Fault
POWERꢀDISSIPATION
28
—
W
1
reCOVery
25
25
ms
9, 10, 11
Step lOaD reSpOnSe
tranSIent
reCOVery
±450
3
±450
3
mV pk
ms
1, 8, 9
Step lIne reSpOnSe
22 - 35 - 22 V
In
—
—
—
—
—
—
—
0
±500
4
—
—
—
—
—
—
—
0
±750
4
mV pk
ms
tranSIent
reCOVery
11
Start-up
Delay
nO lOaD anD Full
35
25
ms
OVerShOOt
50
150
mV pk
1
CapaCItIVe lOaD
unCOnDItIOnally
Stable, Start-up
Delay InCreaSeD
t
= 25°C
—
—
5000
—
—
1000
µF
C
ꢀotes: See page 15
www.interpoint.com
Page 11 of 19
SMRT28 Rev E - 20100216
Crane Aerospace & Electronics Power Solutions
sMrt28 singlꢂ, Dꢀꢄl ꢄnd tꢃiplꢂ spꢄꢇꢂ Dc/Dc convꢂꢃꢁꢂꢃꢈ
28 VOLt Iꢆꢅut – 35 Watt – sꢅace quaLIFIeD
Electrical Characteristics: -55°C to +125°C T , 28 VDC Vin, 100% load, unless otherwise specified.
C
TRIPLE OUTPUT MODEL – SMRT28507T
5 (MAIꢀ)
TYP
±7 (AUXILIARIES)
unItS
parameter
COnDItIOnS
MIꢀ
4.90
MAX
5.10
MIꢀ
6.86
-6.79
TYP
7.00
7.00
MAX
7.14
Output VOltage
MAIꢀ AꢀD POS. AUX
ꢀEꢁ. AUX.
5.00
VDC
-7.21
2, 3
1
Output Current
—
—
—
—
3.0
—
0
±1.00
—
1.2
A
TOTAL
TOTAL
—
2.0
2, 3
1
Output pOwer
0
—
—
15
—
0
±7.0
—
11.2
14
W
V
= 19 tO 56 VDC
—
—
Iꢀ
Output rIpple
10 khz - 20 mhz
MAIꢀ AꢀD POS. AUX
ꢀEꢁ. AUX.
—
—
—
—
—
—
—
—
—
—
5
230
70
—
—
—
—
—
—
—
—
—
—
5
±170
100
150
250
250
350
350
mV p-p
lIne regulatIOn
mV
V
= 19, 50 VDC
—
Iꢀ
lOaD regulatIOn
MAIꢀ AꢀD POS. AUX
100
150
—
V
= 19, 50 VDC
—
—
—
—
—
—
Iꢀ
mV
1
ꢀEꢁ. AUX.
1
V
= 19, 50 VDC
—
Iꢀ
1
tOtal regulatIOn
all COnDItIOnS OF
lIne, lOaD, agIng,
temp anD raDIatIOn
V
4.7
—
5.3
±6.53
—
±7.47
VDC
%
OUT
1, 4, 5
CrOSS regulatIOn
EFFECT Oꢀ
—
—
—
—
—
—
—
2.5
—
t
= 25°C
ꢀEꢁATIVE AUXILIARY
C
Input VOltage
COntInuOuS
19
28
56
VDC
V
tranSIent 100 ms
nO lOaD
0
—
—
—
80
110
50
—
—
—
—
—
—
—
—
—
Input Current
—
—
mA
InhIbIteD
6
Input rIpple Current
10 kHz - 10 MHz
—
71
—
—
—
—
10
—
—
—
—
—
50
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
mA p-p
%
7
eFFICIenCy
8, 9
lOaD Fault
POWERꢀDISSIPATION
22
—
W
1
reCOVery
25
25
ms
9, 10, 11
Step lOaD reSpOnSe
tranSIent
reCOVery
±300
2
±400
2
mV pk
ms
1, 8, 9
Step lIne reSpOnSe
22 - 35 - 22 V
In
—
—
—
—
—
—
—
0
±500
4
—
—
—
—
—
—
—
0
±750
4
mV pk
ms
tranSIent
reCOVery
11
Start-up
Delay
nO lOaD anD Full
20
20
ms
OVerShOOt
100
150
mV pk
1
CapaCItIVe lOaD
unCOnDItIOnally
Stable, Start-up
Delay InCreaSeD
t
= 25°C
—
—
5000
—
—
1000
µF
C
ꢀotes: See page 15
www.interpoint.com
Page 12 of 19
SMRT28 Rev E - 20100216
Crane Aerospace & Electronics Power Solutions
sMrt28 singlꢂ, Dꢀꢄl ꢄnd tꢃiplꢂ spꢄꢇꢂ Dc/Dc convꢂꢃꢁꢂꢃꢈ
28 VOLt Iꢆꢅut – 35 Watt – sꢅace quaLIFIeD
Electrical Characteristics: -55°C to +125°C T , 28 VDC Vin, 100% load, unless otherwise specified.
C
TRIPLE OUTPUT MODEL – SMRT28512T
5 (MAIꢀ)
TYP
±12 (AUXILIARIES)
unItS
parameter
COnDItIOnS
MIꢀ
4.90
MAX
5.10
MIꢀ
TYP
MAX
Output VOltage
MAIꢀ AꢀD POS. AUX
ꢀEꢁ. AUX.
5.00
11.76 12.00 12.24
VDC
-11.58 -12.00 -12.42
2, 3
1
Output Current
—
—
—
—
3.0
—
0
±0.63
—
1
A
TOTAL
TOTAL
—
1.25
2, 3
1
Output pOwer
0
—
—
15
—
0
±7.5
—
12
W
V
= 19 tO 56 VDC
—
—
15
Iꢀ
Output rIpple
10 khz - 20 mhz
MAIꢀ AꢀD POS. AUX
ꢀEꢁ. AUX.
—
—
—
—
200
30
—
—
—
—
—
—
—
—
5
150
30
mV p-p
lIne regulatIOn
mV
V
= 19, 50 VDC
20
5
70
Iꢀ
lOaD regulatIOn
MAIꢀ AꢀD POS. AUX
—
—
—
—
5
40
100
—
40
V
= 19, 50 VDC
—
—
—
—
10
—
120
300
400
Iꢀ
mV
1
ꢀEꢁ. AUX.
1
V
= 19, 50 VDC
—
Iꢀ
1
tOtal regulatIOn
all COnDItIOnS OF
lIne, lOaD, agIng,
temp anD raDIatIOn
V
4.7
—
5.3
±10.9
—
±13.1
VDC
%
OUT
1, 4, 5
CrOSS regulatIOn
EFFECT Oꢀ
—
—
—
—
—
—
—
2.5
—
t
= 25°C
ꢀEꢁATIVE AUXILIARY
C
Input VOltage
COntInuOuS
19
28
56
VDC
V
tranSIent 100 ms
nO lOaD
0
—
—
—
80
110
50
—
—
—
—
—
—
—
—
—
Input Current
—
—
mA
InhIbIteD
6
Input rIpple Current
10 kHz - 10 MHz
—
68
—
—
—
—
10
—
—
—
—
—
50
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
mA p-p
%
7
eFFICIenCy
8, 9
lOaD Fault
POWERꢀDISSIPATION
25
—
W
1
reCOVery
25
25
ms
9, 10, 11
Step lOaD reSpOnSe
tranSIent
reCOVery
±450
3
±450
3
mV pk
ms
1, 8, 9
Step lIne reSpOnSe
22 - 35 - 22 V
In
—
—
—
—
—
—
—
0
±500
4
—
—
—
—
—
—
—
0
±750
4
mV pk
ms
tranSIent
reCOVery
11
Start-up
Delay
nO lOaD anD Full
25
25
ms
OVerShOOt
50
120
mV pk
1
CapaCItIVe lOaD
unCOnDItIOnally
Stable, Start-up
Delay InCreaSeD
t
= 25°C
—
—
5000
—
—
1000
µF
C
ꢀotes: See page 15
www.interpoint.com
Page 13 of 19
SMRT28 Rev E - 20100216
Crane Aerospace & Electronics Power Solutions
sMrt28 singlꢂ, Dꢀꢄl ꢄnd tꢃiplꢂ spꢄꢇꢂ Dc/Dc convꢂꢃꢁꢂꢃꢈ
28 VOLt Iꢆꢅut – 35 Watt – sꢅace quaLIFIeD
Electrical Characteristics: -55°C to +125°C T , 28 VDC Vin, 100% load, unless otherwise specified.
C
TRIPLE OUTPUT MODEL – SMRT28515T
5 (MAIꢀ)
TYP
±15 (AUXILIARIES)
unItS
parameter
COnDItIOnS
MIꢀ
4.92
MAX
5.08
MIꢀ
TYP
MAX
Output VOltage
MAIꢀ AꢀD POS. AUX
ꢀEꢁ. AUX.
5.00
14.77 15.00
15.23
VDC
-14.70 -15.00 -15.30
2, 3
1
Output Current
—
—
—
—
3.0
—
0
±0.5
—
0.80
1
A
TOTAL
TOTAL
—
2, 3
1
Output pOwer
0
—
—
15
—
0
±7.5
—
11.25
15
W
V
= 19 tO 56 VDC
—
—
Iꢀ
Output rIpple
10 khz - 20 mhz
MAIꢀ AꢀD POS. AUX
ꢀEꢁ. AUX.
—
—
—
5
200
25
—
—
—
—
—
—
—
—
—
20
5
200
25
mV p-p
lIne regulatIOn
mV
V
= 19, 50 VDC
35
Iꢀ
lOaD regulatIOn
MAIꢀ AꢀD POS. AUX
—
—
—
—
5
50
100
—
50
V
= 19, 50 VDC
—
—
—
—
—
—
120
500
600
Iꢀ
mV
1
ꢀEꢁ. AUX.
1
V
= 19, 50 VDC
—
Iꢀ
1
tOtal regulatIOn
all COnDItIOnS OF
lIne, lOaD, agIng,
temp anD raDIatIOn
V
4.7
—
5.3
±14.0
—
±16.0
VDC
%
OUT
1, 4, 5
CrOSS regulatIOn
EFFECT Oꢀ
—
—
—
—
—
—
—
2.5
—
t
= 25°C
ꢀEꢁATIVE AUXILIARY
C
Input VOltage
COntInuOuS
19
28
56
VDC
V
tranSIent 100 ms
nO lOaD
0
—
—
—
80
110
50
—
—
—
—
—
—
—
—
—
Input Current
—
—
mA
InhIbIteD
6
Input rIpple Current
10 kHz - 10 MHz
—
70
—
—
—
—
10
—
—
—
—
—
150
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
mA p-p
%
7
eFFICIenCy
8, 9
lOaD Fault
POWERꢀDISSIPATION
25
—
W
1
reCOVery
35
35
ms
9, 10, 11
Step lOaD reSpOnSe
tranSIent
reCOVery
±250
1
±350
1
mV pk
ms
1, 8, 9
Step lIne reSpOnSe
22 - 35 - 22 V
In
—
—
—
—
—
—
—
0
±500
1.5
—
—
—
—
—
—
—
0
±750
1.5
mV pk
ms
tranSIent
reCOVery
11
Start-up
Delay
nO lOaD anD Full
25
20
ms
OVerShOOt
200
350
mV pk
1
CapaCItIVe lOaD
unCOnDItIOnally
Stable, Start-up
Delay InCreaSeD
t
= 25°C
—
—
5000
—
—
1000
µF
C
ꢀotes: See page 15
www.interpoint.com
Page 14 of 19
SMRT28 Rev E - 20100216
Crane Aerospace & Electronics Power Solutions
sMrt28 singlꢂ, Dꢀꢄl ꢄnd tꢃiplꢂ spꢄꢇꢂ Dc/Dc convꢂꢃꢁꢂꢃꢈ
28 VOLt Iꢆꢅut – 35 Watt – sꢅace quaLIFIeD
Electrical Characteristics: -55°C to +125°C Tc, 28 VDC Vin, 100% load, unless otherwise specified.
ꢀOTES: TRIPLE OUTPUT MODELS
1. ꢊꢀꢄꢃꢄnꢁꢂꢂd by dꢂꢈign, noꢁ ꢁꢂꢈꢁꢂd.
2. Up to the maximum specified auxiliary output current/power is available from either auxiliary output provided the total auxiliary output current/
power does not exceed the total current/power specified .
3. To maintain tight regulation over the full input voltage range a minimum load of 2% of full load should be used on all outputs.
4. To maintain the cross regulation specification, one of the auxiliaries must always provide a minimum of 20% of the total auxiliary power used.
ꢀegative Vout cross regulation is referenced to 50%/50% balanced loads (at 100% of total rated output power - full load).
5. Cross regulation is measured under the following conditions:
Condition 1: +POUT = 20 - 80%,/- POUT = 80 - 20%
Condition 2: - POUT = 20 - 80%, /+ POUT = 80 - 20%
6. Converters meet MIL-STD-461 specification revisions for conducted emissions C-CE03 and D-/E-/F-CE-102. The actual value of input ripple
current is much less, the limit in the characteristic table is based on measurement resolution.
7. Efficiency measured with all outputs at full load.
8. Maximum power dissipation when all outputs are shorted simultaneously.
9. Recovery time is measured from application of the transient to point at which VOUT is within 1% of VOUT at final value.
10. Transition time >10 µs.
11. Half load to/from full load.
12. Measured from release of inhibit or input voltage step.
www.interpoint.com
Page 15 of 19
SMRT28 Rev E - 20100216
Crane Aerospace & Electronics Power Solutions
sMrt28 singlꢂ, Dꢀꢄl ꢄnd tꢃiplꢂ spꢄꢇꢂ Dc/Dc convꢂꢃꢁꢂꢃꢈ
28 VOLt Iꢆꢅut – 35 Watt – sꢅace quaLIFIeD
BOTTOM VIEW CASE S
Angled corner
indicates pin 1
Seal hole: 0.135 ±0.005 (3.43 ±0.13)
6 x 0.135 (3.43) dia.
2.205 max (56.01)
3x 2.075 (52.68)
12 x 0.040 ± 0.002 dia.
(1.02 ± 0.05)
1.700 (43.18)
1.500 (38.10)
1.300 (33.02)
14
13
12
11
10
9
1
2
3
4
5
1.100 (27.94)
0.900 (22.86)
0.700 (17.78)
0.500 (12.70)
8
3x 0.125 (3.15)
0.00
Case dimensions in inches (mm)
Tolerance ±0.005 (0.13) for three decimal places
±0.01 (0.3) for two decimal places
unless otherwise specified
CAUTION
Heat from reflow or wave soldering may damage the device.
Solder pins individually with heat application not exceeding 300°C for 10 seconds per pin
Materials
Header Cold Rolled Steel/Nickel
Cover Kovar/Nickel
Pins
#52 alloy/gold, ceramic seal
Case S, Rev C, 20091020
Please refer to the numerical dimensions for accuracy. All information is believed to be accurate,
but no responsibility is assumed for errors or omissions. Interpoint reserves the right to make
changes in products or specifications without notice.
FI g u r e 4: Ca S e S
www.interpoint.com
Page 16 of 19
SMRT28 Rev E - 20100216
Crane Aerospace & Electronics Power Solutions
sMrt28 singlꢂ, Dꢀꢄl ꢄnd tꢃiplꢂ spꢄꢇꢂ Dc/Dc convꢂꢃꢁꢂꢃꢈ
28 VOLt Iꢆꢅut – 35 Watt – sꢅace quaLIFIeD
CL A S S H A N D K, MIL-PRF-38534 EL E M E N T EV A L U A T I O N
COmpOnent-level test
perFOrmed
spaCe prOtOtype (O)
nOn-Qml1
Class h
Qml
Class K
Qml
M/S 2
P 3
M/S 2
P 3
yes
yes
M/S 2
P 3
yes
yes
Element Electrical
Element Visual
yes
no
yes
yes
yes
yes
no
no
Internal Visual
no
no
no
no
no
no
no
N/A
no
no
no
no
no
N/A
no
yes
no
N/A
no
yes
yes
yes
yes
yes
yes
yes
N/A
N/A
yes
yes
yes
no
N/A
yes
yes
N/A
N/A
N/A
N/A
yes
yes
yes
yes
N/A
yes
Temperature Cycling
Constant Acceleration
Interim Electrical
Burn-in
no
no
no
N/A
N/A
N/A
N/A
no
no
N/A
N/A
N/A
N/A
no
no
Post Burn-in Electrical
Steady State Life
Voltage Conditioning Aging
Visual Inspection
Final Electrical
no
no
N/A
N/A
yes
yes
no
no
no
no
yes
yes
N/A
yes
Wire Bond Evaluation
SEM
no
N/A
no
SLAM™/C-SAM:
no
Input capacitors only
(Add’l test, not req. by H or K)
ꢀotes:
1. ꢀon-QML products do not meet all of the requirements of MIL-PRF-38534.
2. M/S = Active components (Microcircuit and Semiconductor Die)
3. P = Passive components
Definitions:
Element Evaluation: Component testing/screening per MIL-STD-883 as determined by MIL-PRF-38534
SEM: Scanning Electron Microscopy
SLAM™: Scanning Laser Acoustic Microscopy
C-SAM: C - Mode Scanning Acoustic Microscopy
SC r e e n I n g ta b l e 1: el e m e n t eV a l u a t I O n
www.interpoint.com
Page 17 of 19
SMRT28 Rev E - 20100216
Crane Aerospace & Electronics Power Solutions
sMrt28 singlꢂ, Dꢀꢄl ꢄnd tꢃiplꢂ spꢄꢇꢂ Dc/Dc convꢂꢃꢁꢂꢃꢈ
28 VOLt Iꢆꢅut – 35 Watt – sꢅace quaLIFIeD
CL A S S H A N D K, MIL-PRF-38534 EN V I R O N M E N T A L SC R E E N I N G
end item-level test
perFOrmed
spaCe prOtOtype (O)
nOn-Qml1
Class h
Qml
Class K
Qml
2
Non-destruct bond pull
Method 2023
no
yes
yes
yes
Pre-cap Inspection
Method 2017, 2032
yes
yes
Temperature Cycle (10 times)
Method 1010, Cond. C, -65°C to 150°C, ambient
yes
yes
yes
yes
yes
yes
Constant Acceleration
Method 2001, 3000 g
PIND Test
Method 2020, Cond. A
2
no
yes
yes
yes
Pre burn-in test
yes
yes
Burn-in
Method 1015, 125°C case, typical
96 hours
160 hours
yes
no
no
no
yes
no
no
no
yes
2 x 160 hours (includes mid-BI test)
Final Electrical Test MIL-PRF-38534
Group A, Subgroups 1 through 6
-55°C, +25°C, +125°C case
yes
N/A
N/A
yes
N/A
N/A
yes
yes
Radiography
Method 2012
Post Radiography Electrical Test
Room temperature
2
yes
Hermeticity Test
Fine Leak, Method 1014, Cond. A
Gross Leak, Method 1014, Cond. C
yes
yes
yes
yes
yes
yes
Final visual inspection
Method 2009
yes
yes
yes
Test methods are referenced to MIL-STD-883 as determined by MIL-PRF-38534.
ꢀotes:
1. Space Prototype (O), non-QML products, do not meet all of the requirements of MIL-PRF-38534.
2. ꢀot required by DSCC but performed to assure product quality.
SC r e e n I n g ta b l e 2: en V I r O n m e n t a l SC r e e n I n g
www.interpoint.com
Page 18 of 19
SMRT28 Rev E - 20100216
Crane Aerospace & Electronics Power Solutions
sMrt28 singlꢂ, Dꢀꢄl ꢄnd tꢃiplꢂ spꢄꢇꢂ Dc/Dc convꢂꢃꢁꢂꢃꢈ
28 VOLt Iꢆꢅut – 35 Watt – sꢅace quaLIFIeD
CL A S S H A N D K, MIL-PRF-38534
RA D I A T I O N HA R D N E S S AS S U R A N C E (RHA)
ENVIRONMENTAL SCREENING LEVELS
SPACE
PROTOTYPE (O)
N O N -QML2
CLASS H
QML
CLASS K
QML
rAdIAtIon hArdneSS
ASSurAnce leVelS 1
3
O
Standard, no radiation guarantee
OO
N/A
N/A
N/A
N/A
N/A
KP
KR
KF
p Radiation tolerant–
Tested lots up to 30 kRads (Si) total dose.
HP
4
2
SEE guarantee up to 80 MeV-cm /mg
r Radiation tolerant–
Tested lots up to 100 kRads (Si) total dose.
HR
N/A
4
2
SEE guarantee up to 80 MeV-cm /mg
F Radiation tolerant–
Tested lots up to 300 kRads (Si) total dose.
4
2
SEE guarantee up to 80 MeV-cm /mg
ꢀotes:
1. Redmond site, Interpoint, has a DSCC approved Radiation Hardness Assurance plan. Our SMD products with RHA “P”, “R,” or “F” code
meet DSCC requirements.
2. Space Prototype (O), non-QML, products do not meet all of the requirements of MIL-PRF-38534.
3. Interpoint model numbers use an “O” in the RHA designator position to indicate the “-” (dash) Radiation Hardness Assurance level of
MIL-PRF-38534, which is defined as “no RHA”
4. ꢀo upset at the pins.
SMRT28 Single, Dual and Triple SMRT28 Rev E - 20100216. This revision supersedes all previous releases. All technical information is believed
to be accurate, but no responsibility is assumed for errors or omissions. Interpoint reserves the right to make changes in products or specifications
without notice. SMRT Series is a trademark of Interpoint. Copyright © 1999 - 2010 Interpoint Corporation. All rights reserved. www.interpoint.com
Page 19 of 19
相关型号：
SMRT28515T/KF
DC-DC Regulated Power Supply Module, 3 Output, 15W, Hybrid, HERMETIC SEALED PACKAGE-14/12
CRANE
©2020 ICPDF网 联系我们和版权申明