5111-51.84M [CONNOR-WINFIELD]
1.8V LVCMOS Surface Mount Crystal Clock Oscillator; 1.8V LVCMOS表面贴装晶体时钟振荡器型号: | 5111-51.84M |
厂家: | CONNOR-WINFIELD CORPORATION |
描述: | 1.8V LVCMOS Surface Mount Crystal Clock Oscillator |
文件: | 总2页 (文件大小:82K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
1.8V LVCMOS Surface Mount
Crystal Clock Oscillator
5111
XO
Features:
30 to 70 MHz
The Connor-Winfield models 5111, 5121,
and 5131 are 7.5mm x 5mm, 1.8V LVCMOS,
Surface Mount, Fixed Frequency Crystal
Oscillators (XO) designed for use in all
applications requiring precision clocks. The
RoHS compliant surface mount package is
designed for high-density mounting and is
optimum for mass production
2111 Comprehensive Drive
1.8V Operation
Aurora, Illinois 60505
RoHS Compliant
Tri-State Enable / Disable Function
Phone: 630-851-4722
Overall Frequency Tolerance:
5111 ± 25 ppm, 5121 ± 50 ppm,
5131 ± 100 ppm
Fax: 630- 851- 5040
www.conwin.com
Temperature Range: 0 to 70°C
Ceramic Surface Mount Package
Tape and Reel Packaging
US Headquarters:
630-851-4722
European Headquarters:
+353-61-472221
Absolute Maximum Ratings
Parameter
Minimum
-55
Nominal
Maximum
125
Units
°C
Vdc
Notes
Storage Temperature
Supply Voltage (Vcc)
-
-
-0.5
3.6
Operating Specifications
Parameter
Minimum
Nominal
Maximum
Units
MHz
ppm
Notes
Frequency Range (Fo)
30
-
-
70
Frequency Tolerance
1
5111
5121
5131
-25
-50
25
50
-100
100
Operating Temp Range
Supply Voltage (Vdd)
Supply Current (Icc)
0
1.71
-
-
1.8
-
70
1.89
15
°C
Vdc
mA
Input Characteristics
Parameter
Minimum
Nominal
Maximum
Units
Vdc
Vdc
nS
Notes
Enable Voltage - (Vih)
Disable Voltage - (Vil)
Enable Time
≥ 70% Vdd
-
-
-
-
-
≤ 30% Vdd
100
2
-
-
-
Disable Time
100
nS
HCMOS Output Characteristics
Parameter
Minimum
Nominal
Maximum
Units
Notes
Load
-
-
15
pF
High (Voh)
Voltage
1.54
-
-
-
-
Vdc
Low (Vol)
0.19
High (loh)
Current
-2
-
-
-
-
mA
Low (lol)
2
Duty Cycle at 50% of Vcc
Rise / Fall Time 10% to 90%
Start-Up Time
40
50
60
3.5
10
5
%
nS
mS
-
-
-
-
-
-
Jitter
pS RMS
Bulletin
Sm072
Notes:
Page
1 of 2
1. Inclusive of calibration @ 25°C , frequency vs temperature stability, supply voltage change, load change, shock and vibration, 10 years aging.
2. Oscillator output is enabled with no connection on pad 1
Revision
01
Date
01 April 2002
Specifications subject to change without notice. All dimensions in inches. © Copyright 1998 The Connor-Winfield Corporation
2111 Comprehensive Drive
Aurora, Illinois 60505
Phone: 630-851-4722
Fax: 630- 851- 5040
www.conwin.com
Package Characteristics
Hermetically sealed ceramic package and metal cover
Suggested Pad Layout
Package
Environmental Characteristics
Temperature Cycle
The specimen shall meet electrical characteristics after
tested 5 cycles of -55°C / 30 minutes and +125°C / 30 minutes
Hermetical
No bubbles appear in Flourinert (FC-43) at 125°C 5°C for 5 minutes
Solvent Resistance
Marking will withstand immersion in
Isopropyl Alcohol or Trichloroethylene
Soldering
Bypass capacitor, C-by, should be
General Conditions 260°C max x 10 sec max x 2 times max or
ceramic capacitor ≥ .01 uf
230°C max x 180 sec max x 1 time
Test Circuit
Typical Operation Data
(Vapor phase reflow)
20 to 100 sec up to 215°C, 50 sec
OSCILLOSCOPE
at 215°C, then down to room temperature per 1 to 5°C / sec
PROBE
POWER
SUPPLY
Mechanical Characteristics
Free Drop
Vibration
The specimen shall meet electrical characteristics after tested 3 times,
OSC
Free Drop testing on the hard wooden board from a height of 75 cm.
The specimen shall meet electrical characteristics after tested
by the following conditions: 10-55Hz 1.5mm Amplitude,
55-2000 Hz 20 G's, 2 hours for each plane
FREQ
COUNTER
INPUT FOR E/D
Thermal Shock
Solderability
After applied Thermal Shock of 260°C
max x 10 sec max x 2 times, or 230°C max x 180 sec max,
the specimen shall meet electrical characteristics
OutputWaveform
(EIAJ-RCX-0102.101 Condition 1a)
1) Flux: MIL-F-14256 (WW Rosin=25%, Isopropyl Alcohol = 75%)
2) Solder: QQ-S-571 (Sn = 63%, Pb = 37%)
3) Solder bath temperature: 235°C 5°C
4) Depth of immersion: Up to electrical terminal
5) Immersing time: Within 2 sec 0.5 sec into solder bath
After performing the above procedures, a newly soldered coverage shall be greater than 90%
SYMMETRY
Pin Connections
1: Enable/Disable
2: Ground
3: Output
4: Vcc
Tape and Reel Dimensions
Ordering Information
5111
- 51.84 MHz
CLOCK
SERIES
CENTER
FREQUENCY
Dimensional Tolerance: ±.02" (.508mm)
±.005"(.127mm)
Bulletin
Page
Sm072
2 of 2
Revision
Date
01
Meets EIA-481A and EIAJ-1009B
2,000 PCS/Reel
01 April 2002
Specifications subject to change without notice. All dimensions in inches. © Copyright 1998 The Connor-Winfield Corporation
相关型号:
51110-0450
2.00mm (.079") Pitch, Milli-Grid™ Crimp Housing, 4 Circuits, without CenterPolarization Key, without Locking Ramp, Leadfree
MOLEX
51110-0452
Board Connector, 4 Contact(s), 2 Row(s), Female, 0.079 inch Pitch, Crimp Terminal, Locking, Black Insulator, Receptacle
MOLEX
51110-0456
Board Connector, 4 Contact(s), 2 Row(s), 0.079 inch Pitch, Crimp Terminal, Locking, Black Insulator, Receptacle,
MOLEX
51110-0460
2.00mm (.079") Pitch, Milli-Grid™ Crimp Housing, 4 Circuits, without CenterPolarization Key, with Locking Ramp, Leadfree
MOLEX
51110-0650
2.00mm (.079") Pitch, Milli-Grid™ Crimp Housing, 6 Circuits, without Center Polarization Key, without Locking Ramp, Leadfree
MOLEX
51110-0656
2.00mm (.079") Pitch, Milli-Grid™ Crimp Housing, 6 Circuits, with Center Locking Rampand Side Polarization Keys, Leadfree
MOLEX
51110-0660
2.00mm (.079") Pitch, Milli-Grid™ Crimp Housing, 6 Circuits, without CenterPolarization Key, with Locking Ramp, Leadfree
MOLEX
51110-0850
2.00mm (.079") Pitch, Milli-Grid™ Crimp Housing, 8 Circuits, without CenterPolarization Key, without Locking Ramp, Leadfree
MOLEX
51110-0851
2.00mm (.079") Pitch, Milli-Grid™ Crimp Housing, 8 Circuits, with Center PolarizationKey, without Locking Ramp, Leadfree
MOLEX
51110-0856
2.00mm (.079") Pitch, Milli-Grid™ Crimp Housing, 8 Circuits, with CenterLocking Rampand Side Polarization Keys, Leadfree
MOLEX
©2020 ICPDF网 联系我们和版权申明