MP9100-0.050-1% [CADDOCK]
RES 0.05 OHM 100W 1% TO247;型号: | MP9100-0.050-1% |
厂家: | Caddock Electronics, Inc. |
描述: | RES 0.05 OHM 100W 1% TO247 电阻器 |
文件: | 总2页 (文件大小:524K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
MP900 and MP9000 Series Kool-Pak®
Power Film Resistors TO-126, TO-220 and TO-247 Style
Page 1 of 2
MP916 Standard Resistance Values:
Tolerance MP916 ±5% Standard (20% is available).
0.010 Ω 5%
0.015 Ω 5%
MP915, MP925, and MP930
Standard Resistance Values:
Tolerance MP915, MP925, and MP930 ±1% Standard - except
as noted. (5% and 20% are available for most resistance values).
0.020 Ω 5% 0.33 Ω
0.025 Ω 5% 0.40 Ω
0.030 Ω 5% 0.50 Ω
0.033 Ω 5% 0.75 Ω
0.040 Ω 5% 1.00 Ω
7.50 Ω
8.00 Ω
10.0 Ω
12.0 Ω
15.0 Ω
20.0 Ω
25.0 Ω
27.0 Ω
30.0 Ω
33.0 Ω
40.0 Ω
47.0 Ω
50.0 Ω
56.0 Ω
75.0 Ω
100 Ω
120 Ω
150 Ω
200 Ω
250 Ω
300 Ω
330 Ω
400 Ω
470 Ω
500 Ω
560 Ω
750 Ω
1.00 K
1.50 K
2.00 K
2.50 K
3.00 K
3.30 K
4.00 K
5.00 K
7.50 K
10.0 K
15.0 K
20.0 K
25.0 K
30.0 K
33.0 K
40.0 K
47.0 K
50.0 K
56.0 K
68.0 K
75.0 K
82.0 K
100 K
0.050 Ω
0.075 Ω
0.10 Ω
0.15 Ω
0.20 Ω
0.25 Ω
0.30 Ω
1.50 Ω
2.00 Ω
2.50 Ω
3.00 Ω
3.30 Ω
4.00 Ω
5.00 Ω
Low Cost Heat Sink Mountable Design featuring
an Exposed Ceramic Heat Dissipating Mounting Surface
Use your thermal design experience with power semiconductors in TO-126, TO-220,
and TO-247 style power packages to help you get the most out of this unique family of
power resistors. The thermal design issues are the same where power handling
capability is based on the case temperature which is maintained in your design.
MP9100 Standard Resistance Values:
Tolerance MP9100 ±1% Standard.
0.050 Ω
0.075 Ω
0.10 Ω
0.15 Ω
0.20 Ω
0.25 Ω
0.30 Ω
0.33 Ω
0.40 Ω
0.50 Ω
0.75 Ω
1.00 Ω
1.50 Ω
2.00 Ω
2.50 Ω
3.00 Ω
3.30 Ω
4.00 Ω
5.00 Ω
7.50 Ω
8.00 Ω
10.0 Ω
12.0 Ω
15.0 Ω
20.0 Ω
25.0 Ω
27.0 Ω
30.0 Ω
33.0 Ω
40.0 Ω
47.0 Ω
50.0 Ω
56.0 Ω
75.0 Ω
100 Ω
MP915 TO-126StylePowerPackage
•
•
•
•
15Wattsat +25°C CaseTemperature, deratedtozeroat +150°C.
ExposedCeramicHeatDissipatingMountingSurface.
ResistanceRangeof 0.020ohmto1K.
For custom resistance values and tolerances contact
applications engineering.
Non-InductiveDesign.
MP916,MP925,andMP930 TO-220StylePowerPackage
Ordering Information:
•
•
•
•
Upto30 Wattsat +25°C CaseTemperature, deratedtozeroat +150°C.
ExposedCeramicHeatDissipatingMountingSurface.
ResistanceRangeof 0.010ohmto100K.
MP915 - 50.0 - 1%
Model Number:
Tolerance
Non-InductiveDesign.
Resistor Value:
Packaging: MP915, MP916, MP925, MP930
resistors are packaged in plastic shipping tubes,
50 pieces per tube. These resistors are available
in a 50 piece minimum quantity and in full tube
quantity increments (i.e. 50, 100, 150, etc.). The
MP9100 resistors are packaged in plastic shipping
tubes, 25 pieces per tube.
MP9100 TO-247StylePowerPackage
•
•
•
•
100 Wattsat +25°C CaseTemperature, deratedtozeroat +175°C.
ExposedCeramicHeatDissipatingMountingSurface.
ResistanceRangeof 0.050ohmto100ohm.
Non-InductiveDesign.
Construction of MP900 and
MP9000 Series:
The MP900 and MP9000 Series Kool-Pak® Power
Film Resistors are constructed with Caddock's
Micronox® resistance film fired onto a flat ceramic
substrate. The terminal attachment and resistance
element geometry are configured to provide
outstanding non-inductive performance. The
ceramic substrate is positioned in the molded
package such that the resistor element and terminal
attachment areas on the substrate are
encapsulated in the molded body with the other side
of the ceramic being exposed flush with the back
mounting surface of the device. This construction is
covered by one or more issued patents, also
patents pending.
New
Power Resistor
with
Exposed Ceramic
Heat Dissipating
Mounting
Surface.
Sales and Applications Engineering
17271 North Umpqua Hwy.
Roseburg, Oregon 97470-9422
Phone: (541) 496-0700
ELECTRONICS, INC.
For Caddock Distributors listed by country see caddock.com/contact/dist.html
e-mail: caddock@caddock.com • web: www.caddock.com
Fax: (541) 496-0408
© 2003-2017 Caddock Electronics, Inc.
28_IL134.0517
Page 2 of 2
Thermal Resistance
Resistance
Model
No.
Max.
Voltage
Power
Rating
Max. Temp.
T MAX
R
Dimensions
Package
Comments
θJC
Min.
Max.
Film (J) to Case (C)
TO-126 Style
TO-220 Style
TO-220 Style
TO-220 Style
TO-247 Style
Figure 1
Figure 2
Figure 2
Figure 2
Figure 3
Ceramic mounting surface
Ceramic mounting surface
MP915
MP916
MP925
MP930
MP9100
1.00 K
200
15 Watts
*
*
0.020 Ω
150°C
150°C
150°C
150°C
175°C
8.33°C/Watt
7.81°C/Watt
5.00°C/Watt
Power
Limited
0.010 Ω
0.019 Ω
16 Watts
100 K
5.00K
500
250
Ceramic mounting surface
Ceramic mounting surface
Ceramic mounting surface
25 Watts
30 Watts
100 Watts
*
4.99 K
*
0.020 Ω
0.050 Ω
4.17°C/Watt
1.50°C/Watt
Power
Limited
100 Ω
*
Derating Curve
Specifications:
100
80
Derating Using Case Temperature (T ):
*
C
Temperature Coefficient for MP915, MP916,
MP925, and MP930:
TC referenced to +25°C, ∆R taken at +150°C
All power and associated overload ratings are derated
based upon case temperature using the derating curve.
The case temperature is measured at the center of the
ceramic mounting surface, with the part properly
mounted and under electrical load. Without a heat sink,
when in free air at +25°C, the MP915 is rated for 1.25
watts, the MP916, MP925, MP930 are rated for 2.25
watts, and the MP9100 is rated for 3.5 watts.
60
40
20
A
B
0.50 ohms and above, -20 to +80 ppm/°C
0.050 ohm to 0.49 ohms, 0 to +200 ppm/°C
0.020 ohm to 0.049 ohm, 0 to +300 ppm/°C
0.010 ohm to 0.019 ohm, 0 to +500 ppm/°C
0
25
100
CASE TEMPERATURE, °C
150 175
A - MP915, MP916, MP925, MP930 Max. Temperature, TMax = 150°C
B - MP9100 Max. Temperature, TMax = 175°C
Temperature Coefficient for MP9100:
TC referenced to +25°C, ∆R taken at +175°C
The thermal design should satisfy the following equation:
Case Temperature (T ) + [Thermal Resistance (R
) x power applied (Watts)] ≤ TMAX considering the full
0.50 ohms and above, -20 to +80 ppm/°C
0.050 ohm to 0.49 ohms, 0 to +150 ppm/°C
c
θJC
operating temperature range of the application.
Mounting Note: Mount on a smooth, clean, and flat heat sink surface with a thermal interface material, such
as thermal grease. The entire exposed ceramic portion must be in thermal contact with the heat sink. When
screw mounting, use a compression washer which provides a mounting force of 150 to 300 pounds (665 to
1330 N). This will provide sufficient pressure on the package over time and through large temperature varia-
tions to maintain the maximum power dissipation capability. Mounting torque to avoid package damage is 8
in-lbs. (0.90 N-m). If a spring clip is used, a clip force of 8 to 30 pounds (35 to 130 N) is recommended to be
applied to the center of the package. The clip should be round or smooth in the contact area to avoid concen-
trating the load on a small point of the plastic body of the package. Another mounting option is to use a
Operating Temperature: -55°C to TMAX
Inductance: MP915, MP916, MP925, and MP930
10nH typical; MP9100, 20nH typical, in series when
measured at a point 0.2 inches from the resistor
body.
pressure bar method which can achieve a greater mounting force with a greater contact area.
For additional applications information regarding mounting and pulse handling see the Caddock
Applications Notes at caddock.com or contact Applications Engineering.
DWV: The dielectric strength rating of 1500 VrmsAC
is based upon connections made between
terminals shorted, and the metal surface the part is
mounted to or a metal clip in contact with the top
surface of the part.
.094 ±.004
(2.39 ±.10) DIA.
.320 ±.010
(8.12 ±.26)
.110 ±.010
(2.79 ±.26)
C
L
+
.440 ±.010
(11.18 ±.26)
Insulation Resistance: 10,000 Megohms min.
The resistor element is electrically isolated from
the mounting surface.
.080 ±.020
(2.03 ±.51)
.115 ±.010
(2.92 ±.26)
MP915
0.10Ω
1%
Figure 1
TO-126 Style
MP915
.053 ± .007
(1.35 ± .18)
.450 ±.050
(11.43 ±1.27)
Load Stability: 2,000 hours at rated power.
∆R ±(1.0 percent + 0.0005 ohm) max. Power
rating dependent upon case temperature. See
derating curve.
.030 ±.004
(.76 ± .10)
.025 ± .004 (.64 ±.10)
.058 ±.007 (1.47 ±.18)
.200 ±.010
(5.08 ±.26)
.410 ±.010
(10.41 ±.26)
.125 ±.010
(3.18 ±.26)
.125 ±.004
(3.18 ±.10) DIA.
Momentary Overload: 1.5 times rated power with
applied voltage not to exceed 1.5 times maximum
continuous operating voltage for 5 seconds. ∆R
±(0.5 percent + 0.0005 ohm) max.
C
L
Figure 2
.640 ±.010
(16.26 ±.26)
.125 ±.010
(3.18 ±.26)
MP930
10.0
1%
TO-220 Style
MP916, MP925
and MP930
.130 ±.030
(3.30 ±.76)
Moisture Resistance: Mil-Std-202, Method 106.
∆R ±(0.5 percent + 0.0005 ohm) max.
.053 ± .007
(1.35 ± .18)
.500 ±.050
(12.70 ±1.27)
.030 ±.004
(.76 ± .10)
Thermal Shock: Mil-Std-202, Method 107, Cond. F.
∆R ±(0.5 percent + 0.0005 ohm) max.
.025 ± .004 (.64 ±.10)
.070 ±.010 (1.78 ±.26)
.200 ±.010
(5.08 ±.26)
Shock: 100G, Mil-Std-202, Method 213, Cond. I.
∆R ±(0.4 percent + 0.0005 ohm) max.
0.195 ± 0.010
(4.95 ± 0.26)
0.620 ± 0.010
(15.75 ± 0.26)
0.143 ± 0.004
(3.63 ± 0.10) Dia.
C
Vibration, High Frequency: Mil-Std-202, Method
204, Cond. D. ∆R ±(0.4 percent + 0.0005 ohm)
max.
L
0.210 ± 0.010
(5.33 ± 0.26)
Figure 3
TO-247 Style
MP9100
0.815 ± 0.010
(20.70 ± 0.26)
Terminal Strength: Mil-Std-202, Method 211,
Cond. A (Pull Test) 5 lbs. ∆R ±(0.2 percent
+ 0.0005 ohm) max.
MP 9100
50.0
1%
0.110 ± 0.030
(2.79 ± 0.76)
0.143 ± 0.007
(3.63 ± 0.18)
Terminal Material: Solderable
0.570 ± 0.050
(14.48 ± 1.27)
0.060 ± 0.004
(1.52 ± 0.10)
Measurement Note: For these specifications,
resistance measurement shall be made at a point
0.2 inch (5.08 mm) from the resistor body.
0.032 +0.004 / -0.010
(0.81 +0.10 / -0.26)
0.400 ± 0.010
(10.16 ± 0.26)
0.095 ± 0.010
(2.41 ± 0.26)
DIMENSIONS IN INCHES AND (MILLIMETERS)
Sales and Applications Engineering
17271 North Umpqua Hwy.
Roseburg, Oregon 97470-9422
Phone: (541) 496-0700
ELECTRONICS, INC.
e-mail: caddock@caddock.com • web: www.caddock.com
For Caddock Distributors listed by country see caddock.com/contact/dist.html
Fax: (541) 496-0408
© 2003-2017 Caddock Electronics, Inc.
28_IL134.0517
相关型号:
©2020 ICPDF网 联系我们和版权申明