91C1D-D16-B15 [BOURNS]
RESISTOR, POTENTIOMETER, CONDUCTIVE PLASTIC, 1 TURN(S), 0.5W, 10000ohm, 5/8 INCH, SQUARE, 3 PINS;型号: | 91C1D-D16-B15 |
厂家: | BOURNS ELECTRONIC SOLUTIONS |
描述: | RESISTOR, POTENTIOMETER, CONDUCTIVE PLASTIC, 1 TURN(S), 0.5W, 10000ohm, 5/8 INCH, SQUARE, 3 PINS PC 电阻器 |
文件: | 总6页 (文件大小:400K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
Features
■ Available in a variety of pin-out
■ DPST and DPDT switch options
■ RoHS compliant versions available*
configurations
■ Virtually infinite electrical circuit isolation
■ Model 96 sealed for board wash
■ Metal or plastic shaft options
91, 92, 93, 94, 95, 96 - 5/8 ” Square Single-Turn Panel Control
97, 99 - 5/8 ” Square Single-Turn Panel Control with Rotary Switch
Potentiometer Specifications
Initial Electrical Characteristics1
Conductive Plastic Element
Cermet Element
Standard Resistance Range
Linear Tapers (A, B, E, & H) ................................................................(B & E) 1 K ohms to 1 megohm......................(A & H) 100 ohms to 1 megohm
Audio Tapers (C, D, F, G, S, & T).........................................................(D,G,S, & T) 1 K ohms to 1 megohm..............(C & F) 1 K ohms to 1 megohm
Total Resistance Tolerance.....................................................................10 % or 20 %.................................................5% or 10%
Independent Linearity............................................................................. 5 %............................................................... 5 %
Absolute Minimum Resistance...............................................................2 ohms maximum........................................... 2 ohms maximum
Effective Electrical Angle ........................................................................(Linear tapers) 240 ° 5 °...............................(Linear tapers) 240 ° ꢀ °
(Audio tapers) 225 ° 5 °
(Audio tapers) 225 ° ꢀ °
Contact Resistance Variation ................................................................. 1 %............................................................... 1 % or ꢁ ohms (ꢂhichever is greater)
Dielectric Withstanding Voltage (MIL-STD-202, Method ꢁ01)
Sea Level............................................................................................1,500 VAC minimum.......................................1,500 VAC minimum
70,000 Feet ........................................................................................500 VAC minimum..........................................500 VAC minimum
Insulation Resistance (500 VDC) ............................................................1,000 megohms minimum..............................1,000 megohms minimum
Poꢂer Rating (Voltage Limited By Poꢂer Dissipation or ꢁ50 VAC, Whichever Is Less)
+70 °C Single Section Assembly .......................................................(Linear tapers) 0.5 ꢂatt...................................(Linear tapers) 2 ꢂatts
(Audio tapers) 0.25 ꢂatt
(Audio tapers) 1 ꢂatt
+70 °C Multiple Section Assembly.....................................................(Linear tapers) 0.5 ꢂatt/section......................(Linear tapers) 1 ꢂatt/section
(Audio tapers) 0.25 ꢂatt/section
(Audio tapers) 0.5 ꢂatt/section
+125 °C ..............................................................................................0 ꢂatt..............................................................0 ꢂatt
Theoretical Resolution............................................................................Essentially infinite...........................................Essentially infinite
Environmental Characteristics1
Operating Temperature Range ...............................................................-40 °C to +125 °C...........................................-40 °C to +125 °C
Storage Temperature Range...................................................................-55 °C to +125 °C...........................................-55 °C to +125 °C
Temperature Coefficient Over Storage Temperature Range................... 1,000 ppm/°C............................................... 150 ppm/°C
Vibration (Single Section)........................................................................15 G................................................................15 G
Total Resistance Shift......................................................................... 2 % maximum.............................................. 2 % maximum
Voltage Ratio Shift.............................................................................. 5 % maximum.............................................. 5 % maximum
Shock (Single Section)............................................................................ꢁ0 G................................................................ꢁ0 G
Total Resistance Shift......................................................................... 2 % maximum.............................................. 2 % maximum
Voltage Ratio Shift.............................................................................. 5 % maximum.............................................. 5 % maximum
Load Life.................................................................................................1,000 hours ....................................................1,000 hours
Total Resistance Shift......................................................................... 10 % maximum............................................ 5 % maximum
Rotational Life (No Load)........................................................................100,000 cycles ...............................................100,000 cycles
Total Resistance Shift.........................................................................(Linear tapers) 10 ohms or 15 % TRS max. ...(All tapers) 5 % TRS max.
(ꢂhichever is greater)
(Audio tapers) 20 % maximum
Contact Resistance Variation @ 50,000 cycles..................................(Linear tapers) 2 %....................................... 2 %
(Audio tapers) ꢁ % ....................................... ꢁ %
Moisture Resistance (MIL-STD-ꢁ0ꢁ, Method 10ꢁ, Condition B)
Total Resistance Shift.........................................................................(Linear tapers) 10 % TRS maximum ............(All tapers) 5 % TRS maximum
(Audio tapers) 20 % TRS maximum
Insulation Resistance (500 VDC)........................................................100 megohms minimum.................................100 megohms minimum
IP Rating (Model 9ꢀ) ...............................................................................IP ꢀ5 ...............................................................IP ꢀ5
(All Others)..........................................................................................IP 40 ...............................................................IP 40
*RoHS Directive 2002/95/EC Jan 27 2003 including Annex
Specifications are subject to change without notice.
Customers should verify actual device performance in their specific applications.
91, 92, 93, 94, 95, 96 - 5/8 ” Square Single-Turn Panel Control
97, 99 - 5/8 ” Square Single-Turn Panel Control with Rotary Switch
Potentiometer Specifications
Mechanical Characteristics1
Stop Strength (1/4 ” D shaft)......................................................................................................................................................................45.19 N-cm (4 lb.-in.)
(1/8 ” D shaft) ....................................................................................................................................................................ꢁꢁ.89 N-cm (ꢁ lb.-in.)
Mechanical Angle ........................................................................................................................................................................................................ꢁ00 ° 5 °
Torque
Starting ....................................................................................................................................................................0.ꢁ max. above average running torque
Running Torque
Single or Dual Section (A ,D & R Bushings) ..............................................................................................................0.21 to 1.0ꢀ N-cm (0.ꢁ to 1.5 oz.-in.)
Single or Dual Section (C & U Bushings) ..................................................................................................................0.14 to 1.0ꢀ N-cm (0.2 to 1.5 oz.-in.)
Mounting ............................................................................................................................................(Metal Bushing) 1.7-2.0 N-m (15-18 lb.-in.) maximum
Plastic Bushing) 5ꢀ-79 N-cm (5-7 lb.-in.) maximum
Variation ................................................................................................................................................0.ꢁ5 N-cm (0.5 oz.-in.) maximum in 45 ° shaft travel
Weight (Single Section, Plastic Bushing) ......................................................................................................................................................7.ꢁ grams nominal
Weight (Single Section, Metal Bushing) ......................................................................................................................................................12.7 grams nominal
(Each Additional Section)..............................................................................................................................................................................4 grams nominal
Terminals ........................................................................................................................................................Printed circuit terminals, J-Hooks or solder lugs
Soldering Condition ......................................................................Recommended hand soldering using Sn95/Ag5 no clean solder, 0.025 ” ꢂire diameter.
Maximum temperature ꢁ99 °C (750 °F) for ꢁ seconds. No ꢂash process to be used ꢂith no clean flux.
Marking............................................................................................................Manufacturer’s trademark, date code, resistance, manufacturer’s part number
Ganging (Multiple Section Potentiometers) ....................................................................................................................................................2 cups maximum
Hardꢂare ............................................One lockꢂasher and one mounting nut is shipped ꢂith each potentiometer, except ꢂhere noted in the part number.
NOTE: ALL MODEL 90 PERFORMANCE SPECIFICATIONS DO NOT APPLY TO UNITS SUBJECTED TO PRINTED CIRCUIT BOARD CLEANING PROCEDURES, EXCEPT FOR THE SEALED
VERSION (MODEL 96).
1AT ROOM AMBIENT: +25 °C NOMINAL AND 50 % RELATIVE HUMIDITY NOMINAL, EXCEPT AS NOTED.
Specifications are subject to change without notice.
Customers should verify actual device performance in their specific applications.
91, 92, 93, 94, 95, 96 - 5/8 ” Square Single-Turn Panel Control
97, 99 - 5/8 ” Square Single-Turn Panel Control with Rotary Switch
Rotary Switch Specifications
Initial Electrical Characteristics1
Contacts:
DPST..................................................................................................................................................................................N.O/N.O., N.C./N.C. or N.O./N.C.
DPDT....................................................................................................................................................................................2 N.O./N.C. (break before make)
Poꢂer Rating (Resistive Load):
DPST ................................................................................................................2 A @ 125 volts RMS-ꢀ0 Hz or 2 A @ 28 VDC, 1 A @ 250 volts RMS-ꢀ0 Hz
DPDT ..............................................................................................................................................................1 A @ 125 volts RMS-ꢀ0 Hz or 1 A @ 28 VDC
Contact Resistance (0.1 VDC-10 mA)........................................................................................................................................................10 milliohms nominal
Contact Bounce ..................................................................................................................................................................................5 milliseconds maximum
Dielectric Withstanding Voltage (MIL-STD-202, Method ꢁ01)
Sea Level ................................................................................................................................................................................................1500 VAC minimum
Insulation Resistance..........................................................................................................................................................................1000 megohms minimum
Environmental Characteristics1
Operating Temperature Range ............................................................................................................................................................................0 °C to +70 °C
Exposure Temperature Range ........................................................................................................................................................................-ꢀ5 °C to +125 °C
Vibration (Dual Section)..........................................................................................................................................................................................................8 G
Contact Resistance ............................................................................................................................................................................10 milliohms maximum
Contact Bounce..............................................................................................................................................................................0.1 millisecond maximum
Shock (Dual Section)............................................................................................................................................................................................................20 G
Contact Resistance ............................................................................................................................................................................10 milliohms maximum
Contact Bounce..............................................................................................................................................................................0.1 millisecond maximum
Rotational Life........................................................................................................................................................................................................25,000 cycles
Sꢂitch Actuating Torque (50% Duty cycle @ Rated Poꢂer Load) ......................................................................................1.41 to 4.94 N-cm (2 to 7 oz.-in.)
Contact Resistance ..........................................................................................................................................................................100 milliohms maximum
Moisture Resistance (MIL-STD-202, Method 10ꢀ, Condition B)
Contact Resistance (0.1 VDC-10 mA) ................................................................................................................................................10 milliohms maximum
Insulation Resistance (After 24 Hours @ Room Temperature) (500 VDC) ........................................................................................100 megohms minimum
Housing Material................................................................................................................................High temperature, flame retardant, thermosetting plastic
Mechanical Characteristics1
Actuating Torque (Each Section, Sꢂitch Module Only) ......................................................................................................ꢁ.5ꢁ to 10.59 N-cm (5 to 15 oz.-in.)
Running Torque (Out of Detent, 2-4 Module Assembly) ......................................................................................................0.21 to 1.41 N-cm (0.ꢁ to 2 oz.-in.)
Detent ......................................................................................................................................................................................................CW or CCW standard
Actuation Angle..............................................................................................................................................................................................................20 ° 5 °
Contact Materials ............................................................................................................................................................................Fine silver ꢂith gold overlay
Terminal Styles ....................................................................................................................................................................................................Solder lug only
Standard Orientation..................................................................................................................................................................In-line ꢂith control terminals
Optional..............................................................................................................................................................................Rotated 90 ° CCW from standard
Terminal Strength (Before and After Soldering Heat Exposure) ............................................................................................................0.9 kg (2 lbs.) minimum
NOTE: Model 99 performance specifications do not apply to units subjected to printed circuit board cleaning procedures.
1At room ambient: +25 °C nominal and 50 % relative humidity nominal, except as noted.
Specifications are subject to change without notice.
Customers should verify actual device performance in their specific applications.
91, 92, 93, 94, 95, 96, 97, 99 - 5/8 ” Square Single-Turn
Product Dimensions
Model 92 J-Hooked
Terminals, In-Line
Model 91 & 96 PC Pin Terminals, In-Line
Model 97 1st Cup Same As Model 93
(2nd Cup - Switch)
.79 .41
(.031 .016)
15.88 .38
(.625 + .015)
15.88
(.625)
REF.
.79
22.86 .43
(.90 .017)
2.77 .38
(1.09 .015)
(.031) 2 PLCS.
1.37
(.054)
13.72
(.54)
9.53 .38
(.375 .015)
6.35 .38
DIA.
(STYLE A)
3
1
12.7
(.50)
MOUNTING
SURFACE
(STYLE C)
.254
(.010)
GAP
(.250 .015)
15.88 .38
(.625 .015)
3
2
1
2.36
(.093)
1
2
3
5.08
(.20)
1.52
(.06)
16.89 .51
(.665 .020)
9.53 .38
(.375 .015)
5
6 2
2.41 X 1.144
(.095 .045)
SEE DETAIL
15.29 .56
(.602 .022)
(MODEL 91 ONLY)
FOR
SLOT 6 PLCS
SHAFT OPTIONS
2.29
(.090)
2.54 0.25
(.100 .010)
6 PLCS.
Model 94 J-Hooked
Terminals, "L" Pattern
2 PLCS.
11.05 .20
.81
(.032)
DIA.
(.435 .008)
2.54
(.100)
10.16
(.40)
2.54
8.26 0.25
(.325 .010)
(.100)
1.52
(.06)
GAP
2.77 .38
(.109 .015)
3
2 1
Model 93 PC Pin Terminals, "L" Pattern
Model 99 1st Cup Same As Model 95
(2nd Cup - Switch)
5.33 .76
(.21 .03)
.81
(.032)
R. MAX.
3.81
(.150)
24.77 .51
(.975 .020)
15.88
(.625)
REF.
MAX. TYP.
2.77 .38
(1.09 .015)
12.7 1.02
(.50 .040)
5.97 .38
(.235 .015)
3
1
Bushing Styles
MOUNTING
SURFACE
3/8 THREADLESS (9.53 mm) (STYLE "D")
3/8-32 UNEF (9.53 mm) (STYLE "A")
1/4-32 UNEF (6.35 mm) (STYLE "C")
M10 X 0.75-6g (STYLE "R")
5.08 .38
(.20 .015)
.81
(.032)
TYP.
5.08
(.20)
DIA. TYP.
11.05 .20
(.435 .008)
10.16 .30
(.40 .012)
M7 X 0.75-6g (STYLE "U")
5.59 .38
(.022 .015)
5
6
2
2.41 X 1.14 4
(.095 .045)
1
1
16.89 .51
(.665 .020)
2
SLOT 6 PLCS
3
2
1
2
3
2.29
(.090)
6 PLCS.
Model 95 Solder Lug Terminals, "Triangular" Pattern
2.77 .38
4.45 .38
(.109 .015)
(.175 .015)
5.08 1.02
(.200 .040)
Switch Module Variations
Shaft Flat Orientation
5.59 .20
(.220 .008)
4.45 .38
(.175 .015)
10.16
2.03
(.080)
3 PLCS.
1
CCW
3
120 ° 5 ° STD.
FLAT ORIENTATION
(SHAFT AT CCW END)
.41
(.016)
4.45 .38
(.175 .015)
2
2.54
(.100)
(.40)
POTENTIOMETER
2.29
(.090)
1.02
(.040)
2.54
(.100)
WIDE X
LONG
3 PLCS.
TOTAL ROTATION 300 °
.128
(.015 )
.XX
CCW DETENT
25 ° MAX.
ACTUATION
ANGLE
TOLERANCES EXCEPT AS SHOWN: DECIMAL .XXX
FRACTION 1/64
.005
CW DETENT
25 ° MAX.
ANGLE 5 °
(.38)
ACTUATION ANGLE
(TYPES 50, 52, 54,
56, 58, 60, 70, 72)
(TYPES 51,
53, 55, 57, 59,
61, 71, 73)
MM
(INCHES)
DIMENSIONS ARE:
NOTE: Switch terminals shown in vertical position.
4
4
4
3
1
3
3
1
4
2
3
1
5
6
2
1
2
2
DPST (NO/NC)
(TYPES 50, 51, 56, 57)
DPST (NC/NC)
DPST (NO/NO)
(TYPES 52, 53, 58, 59)
DPDT (NC/NC)
(TYPES 54, 55, 60, 61)
(TYPES 70, 71, 72, 73)
Switch contacts shown in detent position.
Specifications are subject to change without notice.
Customers should verify actual device performance in their specific applications.
91, 92, 93, 94, 95, 96, 97, 99 - 5/8 ” Square Single-Turn
Product Dimensions
Plastic
Shaft
Styles
SHAFT TYPE "B" (USES BUSHING A OR D)
SHAFT TYPE "D" (USES BUSHING C)
SHAFT TYPE "T" (USES BUSHING U)
1.60+.38/-.00
(.063+.015/-.000)
13.16+.00/-.15
DIA.
1.50 .25
(0.06 .001)
(.1245+.000/-.006)
6.32+.000/-.152
1.19
3.988 +0.000/-0.051
(.157 +.000/-.002)
DIA.
.79
(0.03)
(.249+.000/.006)
(.047)
STD. LENGTHS:
DIA.
12.70
15.88
19.05
STD. LENGTHS:
STD. LENGTHS:
(.500) (.625) (.750)
12.00
(.472)
16.00
22.00
(.630) (.866)
12.70
15.88
19.05
22.23
(.500) (.625) (.750) (.875)
SHAFT TYPE "C" (USES BUSHING A OR D)
SHAFT TYPE "R" (USES BUSHING R)
SHAFT TYPE "W" (USES BUSHING A OR D)
11.18 .38
(.440 .015)
14.27 .25
(.562 .010)
1.80 .25
(0.07 .001)
5.994 +0.000/-0.051
(.236 +.000/-.002)
DIA.
6.31+.025/-.051
(.2485+.001/.002)
DIA.
6.30+.000/-.152
5.49
(.216)
1.00
(.04)
48 TOOTH
(.248+.000/.006)
DIA.
STD. LENGTHS:
STD. LENGTHS:
STD. LENGTHS:
25.40
(1.00)
16.0
(.630)
19.0
(.748) (.866)
22.0
22.23
(.875)
Metal
Shaft
Styles
SHAFT TYPE "A" (USES BUSHING A)
6.32+.010/-.025
SHAFT TYPE "H" (USES BUSHING A)
SHAFT TYPE "V" (USES BUSHING U)
“F” .38
(“F” .015)
6.32+.010/-.025
1.50 0.25
(.059 .010)
3.99+.000/-.035
(.1571+.0000/.0010)
(.2490+.0004/.0010)
(.2490+.0004/.0010)
DIA
DIA
DIA
0.79 0.13
(.031 .054)
5.486 .051
(.216 .002)
STD. LENGTHS:
19.05 22.23
(.500) (.625) (.750) (.875)
STD. LENGTHS:
16.0 19.0
(.472) (.630) (.748)
12.70
15.88
STD. LENGTHS:
15.88 19.05 22.23
(.500) (.625) (.750) (.875)
25.4
(1.000)
12.0
22.0
(.866)
12.70
25.4
(1.000)
FLAT LENGTH “F”:
1.60
4.78
7.95
11.13
14.30
(.563)
(.063) (.188) (.313) (.438)
SHAFT TYPE "Y" (USES BUSHING A)
SHAFT TYPE "J" (USES BUSHING R)
SHAFT TYPE "G" (USES BUSHING A)
9.12
(.359)
1.60+.38/-.00
(.063+.015/-.000)
DIMENSIONS ARE:
1.80 0.25
(.071 .010)
6.00+.000/-.035
(.2362+.0000/.0010)
DIA
6.32+.010/-.025
(.2490+.0004/.0010)
MM
(INCHES)
.762
DIA.
1.27
(.050)
(.030)
5.97
(.235)
DIA.
1.194
(.047)
1.00 0.13
(.039 .054)
21 °
5.03 .05
(.198 .002)
DIA.
STD. LENGTHS:
15.88 19.05 22.23
(.500) (.625) (.750) (.875)
STD. LENGTHS:
5.87
(.231)
8.74
12.70
25.4
(1.000)
12.0
16.0
19.0
22.0
(.866)
1.57
(.472) (.630) (.748)
(.062)
(.344)
STD. LENGTHS:
.02
(.050)
.005
TOLERANCES EXCEPT AS SHOWN: .XX =
19.05
(.750)
.XXX =
(.127)
.0005
(.0127)
.XXXX =
Specifications are subject to change without notice.
Customers should verify actual device performance in their specific applications.
How to Order 90 Series Panel Controls
Models 91 - 96: Part number for multiple section potentiometers
must have a taper and resistance value for each section.
A15
R51
L
L
91
99
A
A
2
2
A
A
-
-
A
B
28
28
-
-
A
A
15
15
/
/
Models 97 & 99: Part number must contain a switch type.
RoHS IDENTIFIER
L
Compliant
ANTI-ROTATION LUG
Blank Non-Compliant
A
Single .305 ” (7.8 mm) R,
90 °CW
C
Single .ꢁ05 ” (7.8 mm) R,
270 °CW
SWITCH TYPE (MODELS 97 & 99 ONLY)
D
No Lug
(R50) DPST N.O./N.C. CW Detent In-Line Term
(R51) DPST N.O./N.C. CCW Detent In-Line Term
(R52) DPST N.O./N.O. CW Detent In-Line Term
(R5ꢁ) DPST N.O./N.O. CCW Detent In-Line Term
(R54) DPST N.C./N.C. CW Detent In-Line Term
(R55) DPST N.C./N.C. CCW Detent In-Line Term
(R5ꢀ) DPST N.O./N.C. CW Detent Horz Term
(R57) DPST N.O./N.C. CCW Detent Horz Term
(R58) DPST N.O./N.O. CW Detent Horz Term
(R59) DPST N.O./N.O. CCW Detent Horz Term
(Rꢀ0) DPST N.C./N.C. CW Detent Horz Term
(Rꢀ1) DPST N.C./N.C. CCW Detent Horz Term
(R70) DPDT CW Detent In-Line Term
# SECTIONS
APPLICABLE MODELS
Models 91 Thru 96 Only
All Models, 2nd Section is
a Sꢂitch in Model 99
1
Single
2
Dual
BUSHING
A
C
D
Metal Plain 3/8 ” (9.53 mm) D x 3/8 ” (9.53 mm) L
Metal Plain 1/4 ” (6.35 mm) D x 1/4 ” (6.35 mm) L
(R71) DPDT CCW Detent In-Line Term
(R72) DPDT CW Detent Horz Term
(R7ꢁ) DPDT CCW Detent Horz Term
Plastic Unthreaded ꢁ/8 ” (9.5ꢁ mm) D
x ꢁ/8 ” (9.5ꢁ mm) L
R
U
Metal Plain 10 mm D x 9 mm L
Metal Plain 7 mm D x 9 mm L
SHAFT
LENGTH
(FMS)
AVAILABLE
ONLY IN
BUSHING
ELEMENT TYPE
TAPER/TOLERANCE
RESISTANCE CODE
VALUE IN OHMS
Code Description
1ꢀ 1/2 ”L
20 5/8 ”L
24 3/4 ”L
28 7/8 ”L
ꢁ2 1 ”L
Code
A, C, D
A, C, D
A, C, D
A, D
MODEL
(A) Linear Cermet ±10 %
(H) Linear Cermet 5 %
(05) - 100
(ꢁ0) - 15 K
(1ꢀ) - 20 K
(17) - 25 K
(18) - 50 K
(19) - 75 K
(20) - 100 K
(ꢁ1) - 150 K
(28) -150
(0ꢀ) - 200
(07) - 250
(08) - 500
(09) - 750
(10) - 1 K
(29) - 1.5 K (21) - 200 K
(11) - 2 K (22) - 250 K
(12) - 2.5 K (2ꢁ) - 500 K
(13) - 5 K (24) - 750 K
91 Single-Turn, In-Line PC Pins
92 Single-Turn, In-Line J-Hooks
9ꢁ Single-Turn, L-Pattern PC Pins
94 Single-Turn, L-Pattern J-Hooks
95 Single-Turn, Triangle-Pattern Solder Lugs
9ꢀ Single-Turn, In-Line PC Pins, Sealed
97 Single-Turn, L-Pattern PC Pins ꢂ/Sꢂitch
A, D
METRIC
12 12 mmL
1ꢀ 1ꢀ mmL
19 19 mmL
22 22 mmL
U
R, U
R
99 Single-Turn, Triangle-Pattern
Solder Lugs w/Switch
R, U
(14) - 7.5 K (25) - 1 M
(15) - 10 K
(B) Linear C-P ±20 %
(E) Linear C-P 10 %
(10) - 1 K
(12) - 2.5 K (20) - 100 K
(13) - 5 K (22) - 250 K
(18) - 50 K
AVAILABLE ONLY IN
(15) - 10 K (2ꢁ) - 500 K
(1ꢀ) - 20 K (25) - 1 M
(17) - 25 K
SHAFT TYPE
LENGTHS
(CODE)
16,20,24,28
BUSHINGS
(CODE)
A,D
B
C
D
R
T
Plastic Single Slotted 1/4 " (6.35 mm) D
Plastic Single Slatted 1/4" (6.35 mm) D
Plastic Single Plain 1/8" (3.18 mm) D
Plastic Single Slotted 6 mm D
(C) CW Audio Cermet 10 %
(D) CW Audio C-P 20 %
(10) - 1 K
(12) - 2.5 K (20) - 100 K
(22) - 250 K
(18) - 50 K
24,28
A,D
C
16,20,24
(F) CCW Audio Cermet 10 % (1ꢁ) - 5 K
(G) CCW Audio C-P 20 %
(S) CW Audio C-P 10 %
(T) CCW Audio C-P 10 %
(15) - 10 K (2ꢁ) - 500 K
(17) - 25 K (25) - 1 M
Metric 16,19,22
Metric 16,19,22
32
R
Plastic Single Slotted 4 mm D
U
W
A
G
H
J
Plastic Single Knurled 1/4" (6.35 mm) D
Metal Single Plain 1/4" (6.35 mm) D
Metal Single Slotted 1/4" (6.35 mm) D
Metal Single Flatted 1/4" (6.35 mm) D
Metal Single Slotted 6 mm D
A,D
A
16,20,24,28,32
16,20,24,28,32
16,20,24,28,32
Metric 12,16,19,22
Metric 12,16,19,22
24
A
Boldface features are Bourns standard options.
All others are available with higher minimum order quantities.
A
R
V
Y
Metal Single Slotted 4 mm D
U
Metal Single Knurled 1/4" (6.35 mm) D
A
REV. 05/08
Specifications are subject to change without notice.
Customers should verify actual device performance in their specific applications.
相关型号:
91C1D-D16-B15L
Potentiometer, Conductive Plastic, 0.5W, 10000ohm, 20% +/-Tol, -1000,1000ppm/Cel, 6350
BOURNS
91C1D-D16-B17
RESISTOR, POTENTIOMETER, CONDUCTIVE PLASTIC, 1 TURN(S), 0.5W, 25000ohm, 5/8 INCH, SQUARE, 3 PINS
BOURNS
91C1D-D16-D15
Potentiometer, Conductive Plastic, 0.25W, 10000ohm, 20% +/-Tol, -1000,1000ppm/Cel, 6350
BOURNS
91C1D-D16-D17
RESISTOR, POTENTIOMETER, CONDUCTIVE PLASTIC, 1 TURN(S), 0.25W, 25000ohm, 5/8 INCH, SQUARE, 3 PINS
BOURNS
91C1D-D16-D17L
Potentiometer, Conductive Plastic, 0.25W, 25000ohm, 20% +/-Tol, -1000,1000ppm/Cel, 6350
BOURNS
91C1D-D16-E18
Potentiometer, Conductive Plastic, 0.5W, 50000ohm, 10% +/-Tol, -1000,1000ppm/Cel, 6350,
BOURNS
©2020 ICPDF网 联系我们和版权申明