ACPL-K54L [BOARDCOM]
Low Power, 1 MBd Digital Optocoupler;
| 型号： | ACPL-K54L |
| 厂家： | 
Broadcom Corporation. |
| 描述： | Low Power, 1 MBd Digital Optocoupler |
| 文件： | 总18页 (文件大小：835K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
ACPL-M50L, ACPL-054L, ACPL-W50L,
ACPL-K54L
Low Power, 1 MBd Digital Optocoupler
Data Sheet
Description
Features
The Broadcom® ACPL-M50L (single-channel in SO-5 footprint),
ACPL-054L (dual-channel in SO-8 footprint), ACPL-W50L
(single-channel in stretched SO-6 footprint), and ACPL-K54L
(dual-channel in stretched SO-8 footprint) are low power,
low-input current, 1 MBd digital optocouplers.
Wide supply voltage Vcc: 2.7V to 24V
Low drive current: 3 mA
Open-collector output
TTL compatible
Compact SO-5, SO-8, stretched SO-6, and stretched SO-8
package
15 kV/μs high common-mode rejection at V = 1500 V
Guaranteed performance from temperature range: –40°C
to +105°C
These digital optocouplers use an insulating layer between the
light-emitting diode and an integrated photon detector to
provide electrical insulation between input and output.
Separate connections for the photodiode bias and output
transistor collector increase the speed up to a hundred times
over that of a conventional photo-transistor coupler by
reducing the base-collector capacitance.
CM
Low propagation delay: 1 μs max at 5V
Worldwide safety approval:
—
UL1577 recognized, 3750 V /1 min for
rms
The ACPL-M50L/054L/W50L/K54L has an increased common
ACPL-M50L/054L, 5000 V /1 min for ACPL-W50L/K54
rms
mode transient immunity of 15 kV/μs minimum at V = 1500V
CM
—
—
CSA Approval
IEC/EN/DIN EN 60747-5-5 Approval for Reinforced
Insulation
over a temperature range of –40°C to 105°C. The current
transfer ratio (CTR) is 140% typical for ACPL-M50L or 130%
typical for ACPL-054L/W50L/K54L at I = 3mA. This digital
F
optocoupler can be used in any TTL/CMOS, TTL/LSTTL, or wide
bandwidth analog applications.
Applications
CAUTION
Take normal static precautions in handling and
assembly of this component to prevent damage
and/or degradation that might be induced by
electrostatic discharge (ESD). The components
featured in this data sheet are not to be used in
military or aerospace applications or
Communications interface
Digital signal isolation
Micro-controller interface
Feedback elements in switching power supplies
Digital isolation for A/D, D/A conversion digital field
environments
Broadcom
- 1 -
ACPL-M50L, ACPL-054L, ACPL-W50L, ACPL-K54L
Data Sheet
Figure 1 Functional Diagram
6
5
V
CC
Anode
V
V
CC
O
1
2
3
6
5
4
Anode
1
3
V
O
NC
Cathode
Cathode
GND
4
GND
ACPL-M50L
ACPL-W50L
Anode1
Cathode1
Cathode2
Anode2
1
2
3
4
8
7
6
5
V
CC
V
O1
V
O2
GND
ACPL-054L/K54L
Table 1 Truth Table
LED
VO
ON
LOW
OFF
HIGH
NOTE The connection of a 0.1-μF bypass capacitor between pins 4 and 6 for ACPL-M50L/W50L and between pins 5 and 8
for ACPL-054L/K54L is recommended.
Broadcom
- 2 -
ACPL-M50L, ACPL-054L, ACPL-W50L, ACPL-K54L
Data Sheet
Ordering Information
ACPL-M50L and ACPL-054L are UL Recognized with 3750 V for 1 minute per UL1577. ACPL-W50L and ACPL-K54L are UL
rms
Recognized with 5000 V for 1 minute per UL1577.
rms
Table 2 Ordering Information
Option
IEC/EN
60747-5-5
Part Number
Package
Surface Mount Tape and Reel
Quantity
RoHS
Compliant
ACPL-M50L
-000E
-060E
-500E
-560E
-000E
-060E
-500E
-560E
-000E
-060E
-500E
-560E
-000E
-060E
-500E
-560E
SO-5
X
X
100 per tube
X
X
X
X
X
X
X
X
100 per tube
1500 per reel
1500 per reel
100 per tube
100 per tube
1500 per reel
1500 per reel
100 per tube
100 per tube
1000 per reel
1000 per reel
80 per tube
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
ACPL-054L
ACPL-W50L
ACPL-K54L
SO-8
X
X
Stretched SO-6
Stretched SO-8
X
X
80 per tube
X
X
1000 per reel
1000 per reel
To order, choose a part number from the part number column and combine with the desired option from the option column to
form an order entry.
Example 1:
ACPL-M50L-500E to order product of Mini-flat Surface Mount 5-pin package in Tape and Reel packaging with RoHS compliant.
Option data sheets are available. Contact your Broadcom sales representative or authorized distributor for information.
Broadcom
- 3 -
ACPL-M50L, ACPL-054L, ACPL-W50L, ACPL-K54L
Data Sheet
Package Outline Drawings
Figure 2 ACPL-M50L SO-5 Package (JEDEC M0-155)
1
3
6
5
VCC
ANODE
M50L
7.0 0.2
4.4 0.1
VOUT
GND
(0.276 0.008ꢀ
YWW
(0.173 0.004ꢀ
4
CATHODE
0.4 0.05
(0.016 0.002ꢀ
3.6 0.1ꢁ
(0.142 0.004ꢀ
0.102 0.102
0.216 0.038
2.5 0.1
(0.004 0.004ꢀ
(0.0085 0.0015ꢀ
(0.098 0.004ꢀ
7° MAX.
0.71
1.27
BSC
MIN
(0.028ꢀ
(0.050ꢀ
Dimensions in Millimeters (Inches)
* Maximum mold flash on each side is 0.15 mm (0.006)
MAX. LEAD COPLANARITY
= 0.102 (0.004ꢀ
Note: Floating lead protrusion is 0.15 mm (6 mils) max.
Figure 3 Land Pattern Recommendations
4.4
(0.17ꢀ
1.3
(0.05ꢀ
2.5
(0.10ꢀ
1.8
(0.072ꢀ
0.64
(0.025ꢀ
8.27
(0.325ꢀ
Dimension in Millimeters (Inches)
Broadcom
- 4 -
ACPL-M50L, ACPL-054L, ACPL-W50L, ACPL-K54L
Data Sheet
Figure 4 ACPL-054L (Small Outline SO-8 Package)
LAND PATTERN RECOMMENDATION
LEAD FREE
8
1
7
2
6
5
4
5.994 0.203
(0.236 0.008ꢀ
xꢀ
54LV
3.937 0.127
(0.155 0.005ꢀ
TYPE NUMBER
(‘V’ for OPTION 060ꢀ
DATE CODE
7.49 (0.295ꢀ
YWW
3
PIN ONE
1.9 (0.075ꢀ
0.406 0.076
(0.016 0.003ꢀ
1.270
(0.050ꢀ
BSC
0.64 (0.025ꢀ
0.432
(0.017ꢀ
ꢁ
7°
5.080 0.127
(0.200 0.005ꢀ
45° X
3.175 0.127
(0.125 0.005ꢀ
0 ~ 7°
0.228 0.025
(0.009 0.001ꢀ
1.524
(0.060ꢀ
Total package length (inclusive of mold flash)
5.207 0.25ꢀ (0.205 0.010)
*
0.203 0.102
(0.008 0.004ꢀ
Dimensions in Millimeters (Inches).
Lead coplanarity = 0.10 mm (0.00ꢀ inches) max.
0.305
(0.012ꢀ
MIN.
Option number 500 not marked.
Note: Floating lead protrusion is 0.15 mm (6 mils) max.
Broadcom
- 5 -
ACPL-M50L, ACPL-054L, ACPL-W50L, ACPL-K54L
Data Sheet
Figure 5 ACPL-W50L Stretched SO-6 Package
TOTAL PACKAGE WIDTH
(INCLUSIVE OF MOLD FLASHꢀ
4.834 0.254
(0.190 0.010ꢀ
LAND PATTERN RECOMMENDATION
12.65 (0.498ꢀ
1.27 (0.050ꢀ BSG
6
5
4
ROHS-COMPLIANCE
INDICATOR
0.76 (0.030ꢀ
1.91 (0.075ꢀ
PART NUMBER
DATE CODE
W50L
YWW
+0.127
1
2
3
6.807
0.268
0
0.381 0.127
(0.015 0.005ꢀ
+0.005
- 0.000
(
ꢀ
1.590 0.127
(0.063 0.005ꢀ
7°
7°
0.45 (0.018ꢀ
45°
3.180 0.127
(0.125 0.005ꢀ
0.20 0.10
(0.008 0.004ꢀ
0.750 0.250
(0.0295 0.010ꢀ
Dimensions in Millimeters (Inchesꢀ.
Lead coplanarity = 0.1 mm (0.004 inchesꢀ.
11.50 0.250
(0.453 0.010ꢀ
Broadcom
- 6 -
ACPL-M50L, ACPL-054L, ACPL-W50L, ACPL-K54L
Data Sheet
Figure 6 ACPL-K54L Stretched SO-8 Package
TOTAL PACKAGE WIDTH
(INCLUSIVE OF MOLD FLASHꢀ
6.100 0.250
(0.240 0.010ꢀ
1.270 (0.050ꢀ BSG
LAND PATTERN RECOMMENDATION
8
7
6
5
ROHS-COMPLIANCE
INDICATOR
PART NUMBER
DATE CODE
K54L
YWW
1.905 (0.1ꢀ
12.650 (0.5ꢀ
1
2
3
4
0.381 0.13
1.590 0.127
(0.063 0.005ꢀ
(0.015 0.005ꢀ
7°
7°
0.450 (0.018ꢀ
45°
3.180 0.127
(0.125 0.005ꢀ
0.200 0.100
(0.008 0.004ꢀ
6.807 0.127
(0.268 0.005ꢀ
0.750 0.250
(0.0295 0.010ꢀ
Dimensions in Millimeters (Inchesꢀ.
Lead coplanarity = 0.1 mm (0.004 inchesꢀ.
11.5 0.250
(0.453 0.010ꢀ
Solder Reflow Profile
Recommended reflow condition as per JEDEC Standard, J-STD-020 (latest revision). Non-halide flux should be used.
Regulatory Information
The ACPL-M21L/024L/021L/W21L/K24L is approved by the following organizations.
UL
Approval under UL 1577, component recognition program up to VISO = 3750 VRMS for ACPL-M50L/054L/021L and
ISO = 5000 VRMS for ACPL-W50L/K54L.
V
CSA
Approval under CSA Component Acceptance Notice #5.
(Option 060E only).
IEC/EN 60747-5-5
Broadcom
- 7 -
ACPL-M50L, ACPL-054L, ACPL-W50L, ACPL-K54L
Data Sheet
Table 3 Insulation and Safety Related Specifications
ACPL-W50L
ACPL-K24L
Parameter
Symbol ACPL-M50L ACPL-054L
Units
Conditions
Minimum External Air Gap
(Clearance)
L(101)
L(102)
5
5
4.9
4.8
8
mm Measured from input terminals to output
terminals, shortest distance through air.
Minimum External Tracking
(Creepage)
8
mm Measured from input terminals to output
terminals, shortest distance path along body.
Minimum Internal Plastic Gap
(Internal Clearance)
0.08
0.08
0.08
mm Through insulation distance conductor to
conductor, usually the straight line distance
thickness between the emitter and detector.
Tracking Resistance
CTI
175
IIIa
175
IIIa
175
IIIa
V
DIN IEC 112/VDE 0303 Part 1
(Comparative Tracking Index)
Isolation Group
—
Material Group (DIN VDE 0110, 1/89, Table 1)
Table 4 IEC/EN60747-5-5 Insulation Characteristicsa (Option 060E)
Description
Characteristic
Unit
Symbol
ACPL-M21L/
024L/021L
ACPL-W21L/
K24L
Installation classification per DIN VDE 0110/39, Table 1
for rated mains voltage ≤ 150 Vrms
for rated mains voltage ≤ 300 Vrms
for rated mains voltage ≤ 600 Vrms
for rated mains voltage ≤ 1000 Vrms
—
I – IV
I – III
I – II
I – IV
I – IV
I – III
I – III
Climatic Classification
55/105/21
55/105/21
—
—
Pollution Degree (DIN VDE 0110/39)
Maximum Working Insulation Voltage
2
2
VIORM
VPR
560
1140
Vpeak
Input to Output Test Voltage, Method ba
1050
2137
1824
8000
Vpeak
Vpeak
Vpeak
V
IORM × 1.875 = VPR, 100% Production Test with tm = 1 sec, Partial discharge < 5 pC
Input to Output Test Voltage, Method aa
IORM × 1.6 = VPR, Type and Sample Test, tm = 10 sec, Partial discharge < 5 pC
VPR
896
V
Highest Allowable Overvoltage (Transient Overvoltage tini = 60 sec)
VIOTM
6000
Safety-limiting values – maximum values allowed in the event of a failure.
Case Temperature
Input Currentb
Output Powerb
TS
150
150
600
175
230
600
°C
mA
mW
IS, INPUT
PS, OUTPUT
>109
>109
Insulation Resistance at TS, VIO = 500 V
RS
a.
Refer to the optocoupler section of the Isolation and Control Components Designer’s Catalog, under Product Safety Regulations section, (IEC/EN 60747-5-5) for
a detailed description of Method a and Method b partial discharge test profiles.
b. Refer to the following figure for dependence of PS and IS on ambient temperature.
NOTE These optocouplers are suitable for "safe electrical isolation" only within the safety limit data. Maintenance of the
safety limit data shall be ensured by means of protective circuits.
Broadcom
- 8 -
ACPL-M50L, ACPL-054L, ACPL-W50L, ACPL-K54L
Data Sheet
Table 5 Absolute Maximum Ratings
Parameter
Symbol
Min.
–55
Max.
125
Units
°C
Storage Temperature
Operating Temperature
Lead Soldering Cycle
TS
TA
–40
105
°C
Temperature
Time
—
—
—
260
10
°C
s
Average Forward Input Currenta
IF(avg)
IF(peak)
IF(trans)
VR
20
mA
Peak Forward Input Currentb (50% duty cycle, 1 ms pulse width)
Peak Transient Input Current (≤1 μs pulse width, 300 ps)
—
—
—
—
—
40
1
mA
A
Reversed Input Voltage
Input Power Dissipationc
5
V
PIN
36
45
mW
nW
Output Power Dissipationd
Average Output Current
Peak Output Current
Supply Voltage
PO
IO(AVG)
IO(PEAK)
VCC
—
—
8
mA
mA
V
16
30
–0.5
Output Voltage
VO
–0.5
24
V
Solder Reflow Temperature Profile
See Package Outline Drawings
a. Derate linearly above 85°C free-air temperature at a rate of 0.5 mA/°C.
b. Derate linearly above 85°C free-air temperature at a rate of 1.0 mA/°C.
c.
Derate linearly above 85°C free-air temperature at a rate of 0.9 mW/°C.
d. Derate linearly above 85°C free-air temperature at a rate of 1.2 mW/°C.
Table 6 Recommended Operating Conditions
Parameter
Supply Voltage
Symbol
VCC
Min.
2.7
3
Max.
24
Units
V
Input Current, High Level
Operating Temperature
Forward Input Voltage (OFF)
IFH
10
mA
°C
TA
–40
—
105
0.8
VF (OFF)
V
Broadcom
- 9 -
ACPL-M50L, ACPL-054L, ACPL-W50L, ACPL-K54L
Data Sheet
Electrical Specifications (DC)
Over recommended temperature (T = –40°C to +105°C) and supply voltage (2.7V ≤ V ≤ 24V). All typical specifications are at
A
CC
T = 25°C.
A
Table 7 Electrical Specifications (DC)
Part
Number
Parameter
Sym.
Min.
Typ.
Max.
Units
Conditions
Fig.
CTRa
Current Transfer
Ratio
ACPL-M50L
100
80
140
—
200
—
%
%
%
%
TA = 25°C VO = 0.4V
VO = 0.5V
VCC = 3.3V or 5V,
IF = 3 mA
8, 9
ACPL-054L
ACPL-W50L
ACPL-K54
93
130
—
200
—
TA = 25°C VO = 0.4V
VO = 0.5V
VCC= 3.3V or 5V,
IF = 3 mA
8, 9
53
Logic Low Output
Voltage
VOL
—
—
—
—
—
—
0.2
0.2
0.4
0.5
0.5
1
V
V
TA = 25°C IO = 3 mA
VCC = 3.3V or 5V,
IF = 3 mA
I
O = 1.6 mA
TA = 25°C VO = VCC = 5.5V
O = VCC = 24V
Logic High
Output Current
IOH
0.003
0.01
—
μA
IF =0 mA
10, 11
V
80
VO = VCC = 24V
Logic Low Supply
Currentper
Channel
ICCL
36
100
μA
μA
IF = 3 mA,
V
V
O = open,
CC = 24V
Logic High Supply
Current per
Channel
ICCH
—
0.02
2
IF = 0 mA,
V
V
O = open,
CC = 24V
Input Forward
Voltage
VF
—
—
5
1.5
1.5
—
1.8
1.95
—
V
V
V
TA= 25°C IF = 3 mA
IF = 3 mA
7
Input Reversed
Breakdown
Voltage
BVR
IR = 10 μA
Temperature
Coefficient of
Forward Voltage
VF/TA
—
—
–1.6
77
—
—
mV/°C
pF
IF= 3 mA
Input Capacitance
CIN
F = 1 MHz, VF = 0
a.
CURRENT TRANSFER RATIO in percent is defined as the ratio of output collector current, IO, to the forward LED input current, IF, times 100%.
Broadcom
- 10 -
ACPL-M50L, ACPL-054L, ACPL-W50L, ACPL-K54L
Data Sheet
Switching Specifications (ACPL-M50L)
Over recommended operating (T = –40°C to 105°C), I = 3 mA, (2.7V ≤ V ≤ 24V), unless otherwise specified.
A
F
CC
Table 8 Switching Specifications (ACPL-M50L)
Parameter
Symbol Min
Typ
Max
Units
Test Conditions
TA = 25°C Pulse: f = 10 kHz, Duty cycle = 50%, IF = 3 mA,
CC = 3.3V, RL= 1.2 k, CL = 15 pF, VTHHL = 1.5V
Fig.
Propagation Delay
Time to Logic Low at
Output
TPHL
TPLH
PWD
—
0.2
0.5
μs
26
V
—
—
0.2
1
μs
μs
12, 26
26
0.22
0.5
TA = 25°C Pulse: f = 10 kHz, Duty cycle = 50%, IF = 3 mA,
CC = 5.0V, RL = 1.9 k, CL = 15 pF, VTHHL = 1.5V
V
—
—
0.22
0.33
1
μs
μs
14, 26
26
0.7
TA = 25°C Pulse: f = 10 kHz, Duty cycle = 50%, IF = 3 mA,
CC = 24V, RL = 10 k, CL = 15 pF, VTHHL = 1.5V
V
—
—
0.33
0.38
1.3
0.8
μs
μs
16, 26
26
Propagation Delay
Time to Logic High at
Output
TA = 25°C Pulse: f = 10 kHz, Duty cycle = 50%, IF = 3 mA,
CC = 3.3V, RL = 1.2 k, CL = 15 pF, VTHHL = 2.0V
V
—
—
0.38
0.31
1.2
0.7
μs
μs
12, 26
26
TA = 25°C Pulse: f = 10 kHz, Duty cycle = 50%, IF= 3 mA,
CC = 5.0V, RL = 1.9 k, CL = 15 pF, VTHHL = 2.0V
V
—
—
0.31
0.3
1
μs
μs
14, 26
26
0.7
TA = 25°C Pulse: f = 10 kHz, Duty cycle = 50%, IF = 3 mA,
CC = 24V, RL = 10 k, CL = 15 pF, VTHHL = 2.0V
V
—
—
0.3
1
μs
μs
16, 26
26
Pulse Width
Distortiona
0.18
0.8
TA = 25°C Pulse: f = 10 kHz, Duty cycle = 50%, IF = 3 mA,
VCC = 3.3V, RL = 1.2 k, CL = 15 pF, VTHHL = 1.5V,
—
0.18
1.2
μs
26
V
THLH = 2.0V
TA = 25°C Pulse: f = 10 kHz, Duty cycle = 50%, IF = 3 mA,
CC = 5.0V, RL = 1.9 k, CL = 15 pF, VTHHL = 1.5V,
—
—
0.1
0.1
0.7
1
μs
μs
26
26
V
VTHLH = 2.0V
—
—
0.1
0.1
0.7
1
μs
μs
TA = 25°C Pulse: f = 10 kHz, Duty cycle = 50%, IF = 3 mA,
26
26
V
V
CC=24V, RL=10 k, CL=15 pF, VTHHL=1.5V,
THLH=2.0V
Propagation Delay
Difference Between
tpsk
—
0.18
0.7
μs
μs
μs
TA = 25°C Pulse: f = 10 kHz, Duty cycle = 50%, IF = 3 mA,
V
V
CC = 3.3V, RL = 1.2 k, CL = 15 pF, VTHHL = 1.5V,
THLH = 2.0V
Any Two Partsb
—
0.1
0.6
TA = 25°C Pulse: f = 10 kHz, Duty cycle = 50%, IF = 3 mA,
V
V
CC = 5.0V, RL = 1.9 k, CL = 15 pF, VTHHL = 1.5V,
THLH = 2.0V
—
15
0.1
25
0.6
—
TA = 25°C Pulse: f = 10 kHz, Duty cycle = 50%, IF = 3 mA,
CC = 24V, RL = 10 k, CL = 15 pF, VTHHL = 2.0V
V
Common Mode
|CMH|
|CML|
kV/μs TA = 25°C VCM = 1500V, IF = 0 mA,, RL = 1.2 k or 1.9 k,
CC = 3.3 V or 5V
27
Transient Immunity at
V
Logic High Outputc
Common Mode
15
10
20
15
—
—
kV/μs TA= 25°C VCM = 1500V, IF = 3 mA, RL = 1.2 k, VCC = 5V
kV/μs VCM = 1500V, IF = 3 mA, RL = 1.2 k, VCC = 3.3 V
27
27
Transient Immunity at
Logic Low Outputd
a.
Pulse Width Distortion (PWD) is defined as |tPHL – tPLH| for any given device.
b. The difference between tPLH and tPHL between any two parts under the same test condition. (See IPM Dead Time and Propagation Delay Specifications section.)
c.
Common transient immunity in a Logic High level is the maximum tolerable (positive) dVCM/dt on the rising edge of the common mode pulse, VCM, to assure
that the output will remain in a Logic High state (i.e., VO > 2.0V).
d. Common mode transient immunity in a Logic Low level is the maximum tolerable (negative) dVCM/dt on the falling edge of the common mode pulse signal,
VCM to assure that the output will remain in a Logic Low state (i.e., VO < 0.8V).
Broadcom
- 11 -
ACPL-M50L, ACPL-054L, ACPL-W50L, ACPL-K54L
Data Sheet
Switching Specifications (ACPL-054L/W50L/K54L))
Over recommended temperature (T = –40°C to +105°C), supply voltage (2.7V ≤ V ≤ 24V unless otherwise specified..
A
CC
Table 9 Switching Specifications (ACPL-M50L)
Parameter
Symbol Min
Typ
Max
Units
Test Conditions
Fig.
Propagation Delay
Time to Logic Low at
Output
TPHL
TPLH
PWD
—
0.2
0.5
μs
TA = 25°C Pulse: f = 10 kHz, Duty cycle = 50%, IF = 3 mA, VCC 26
= 3.3V, RL = 1.8 k, CL = 15 pF, VTHHL = 1.5V
—
—
0.2
1
μs
μs
13, 26
26
0.22
0.5
TA = 25°C Pulse: f = 10 kHz, Duty cycle = 50%, IF = 3 mA,
CC = 5.0V, RL = 2.9 k, CL = 15 pF, VTHHL = 1.5V
V
—
—
0.22
0.33
1
μs
μs
15, 26
26
0.7
TA = 25°C Pulse: f = 10 kHz, Duty cycle = 50%, IF = 3 mA,
CC = 24V, RL = 14.8 k, CL = 15 pF, VTHHL= 1.5V
V
—
—
0.33
0.38
1.3
0.8
μs
μs
17, 26
26
Propagation Delay
Time to Logic High at
Output
TA = 25°C Pulse: f = 10 kHz, Duty cycle = 50%, IF = 3 mA,
CC = 3.3V, RL = 1.8 k, CL =1 5 pF, VTHHL = 2.0V
V
—
—
0.38
0.31
1.4
0.7
μs
μs
13, 26
26
TA = 25°C Pulse: f = 10 kHz, Duty cycle = 50%, IF = 3 mA,
CC = 5.0V, RL = 2.9 k, CL = 15 pF, VTHHL = 2.0V
V
—
—
0.31
0.3
1
μs
μs
15, 26
26
0.7
TA = 25°C Pulse: f = 10 kHz, Duty cycle = 50%, IF = 3 mA,
CC = 24V, RL = 14.8 k, CL = 15 pF, VTHHL = 2.0V
V
—
—
0.3
1
μs
μs
17, 26
26
Pulse Width
Distortiona
0.18
0.8
TA = 25°C Pulse: f = 10 kHz, Duty cycle = 50%, IF = 3 mA,
VCC = 3.3V, RL = 1.8 k, CL = 15 pF, VTHH L= 1.5V,
—
0.18
1.4
μs
26
V
THLH = 2.0V
TA = 25°C Pulse: f = 10 kHz, Duty cycle = 50%, IF= 3 mA,
CC =5.0V, RL = 2.9 k, CL = 15 pF, VTHHL = 1.5V,
—
—
0.1
0.1
0.7
1
μs
μs
26
26
V
VTHLH = 2.0V
—
—
0.1
0.1
0.7
1
μs
μs
TA = 25°C Pulse: f = 10 kHz, Duty cycle = 50%, IF = 3 mA,
26
26
V
V
CC = 24V, RL = 14.8 k, CL = 15 pF, VTHHL = 1.5V,
THLH = 2.0V
Propagation Delay
Difference Between
tpsk
—
—
—
15
0.18
0.1
0.1
25
0.7
0.6
0.6
—
μs
μs
μs
TA = 25°C Pulse: f = 10 kHz, Duty cycle = 50%, IF= 3 mA,
V
V
CC = 3.3V, RL = 1.8 k, CL = 15 pF, VTHHL = 1.5V,
THLH = 2.0V
Any Two Partsb
TA = 25°C Pulse: f = 10 kHz, Duty cycle = 50%, IF = 3 mA,
V
V
CC = 5.0V, RL = 2.9 k, CL = 15 pF, VTHHL = 1.5V,
THLH = 2.0V
TA = 25°C Pulse: f = 10 kHz, Duty cycle = 50%, IF = 3 mA,
V
V
CC = 24V, RL = 14.8 k, CL = 15 pF, VTHHL = 2.0V,
THLH = 2.0V
Common Mode
|CMH|
|CML|
kV/μs TA = 25°C VCM = 1500V, IF = 0 mA,, RL = 1.8 k or 2.9 k,
CC = 3.3 V or 5V
27
Transient Immunity at
V
Logic High Outputc
Common Mode
15
15
20
20
—
—
kV/μs TA= 25°C VCM = 1500V, IF = 3 mA, RL = 2.9 k, VCC = 5V
kV/μs VCM = 1500V, IF = 3 mA, RL = 1.8 k, VCC = 3.3 V
27
27
Transient Immunity at
Logic Low Outputd
a.
Pulse Width Distortion (PWD) is defined as |tPHL – tPLH| for any given device.
b. The difference between tPLH and tPHL between any two parts under the same test condition. (See IPM Dead Time and Propagation Delay Specifications section.)
c.
Common transient immunity in a Logic High level is the maximum tolerable (positive) dVCM/dt on the rising edge of the common mode pulse, VCM, to assure
that the output will remain in a Logic High state (i.e., VO > 2.0V).
d. Common mode transient immunity in a Logic Low level is the maximum tolerable (negative) dVCM/dt on the falling edge of the common mode pulse signal,
VCM to assure that the output will remain in a Logic Low state (i.e., VO < 0.8V).
Broadcom
- 12 -
ACPL-M50L, ACPL-054L, ACPL-W50L, ACPL-K54L
Data Sheet
Package Characteristics
All typical at T = 25°C
A
Table 10 Package Characteristics
Parameter
Symbol
Part Number
ACPL-M50L/054L
ACPL-W50L/K54L
Min.
Typ.
Max.
Units
Test Conditions
Input-Output Momentary Withstand
Voltagea,b
VISO
3750
—
—
Vrms RH ≤ 50%, t = 1 min., TA = 25°C
5000
—
—
—
—
Input-Output Resistancea
Input-Output Capacitancea
RI-O
CI-O
II-I
1014
pF
μA
VI-O = 500 Vdc
—
—
0.6
—
—
f = 1 MHz, TA = 25°C
RH ≤ 45%, t = 5 s, VI-I = 500Vdc
Input-Input Insulation Leakage
Current[3]
0.005
Input-Input Resistancec
Input-Input Capacitancec
RI-I
CI-I
—
—
1011
0.25
—
—
pF
f = 1 MHz
a.
Device considered a two terminal device: pins 1 and 3 shorted together and pins 4, 5 and 6 shorted together for ACPL-M50L, pins 1, 2, 3 and 4 shorted together
and pins 5, 6, 7 and 8 shorted together for ACPL-054L/K54L, pins 1, 2 and 3 shorted together and pins 4, 5 and 6 shorted together for ACPL-W50L.
b. In accordance with UL 1577, each optocoupler is proof tested by applying an insulation test voltage ≥ 4500 VRMS for 1 second for ACPL-M50L/054L and
≥ 6000 VRMS for 1 second for ACPL-W50L/K54L (leakage detection current limit, II-O ≤ 5mA)..
c.
Measured between pins 1 and 2 shorted together and pins 3 and 4 shorted together for ACPL-054L/K54L.
Broadcom
- 13 -
ACPL-M50L, ACPL-054L, ACPL-W50L, ACPL-K54L
Data Sheet
Figure 7 Input Current vs. Forward Voltage
Figure 8 Typical Current Transfer Ratio vs. Temperature
100
1.1
1
TA = 25°C
10
1
0.1
0.9
IF
0.8
0.01
NORMALIZED
IF = 3 mA
VF
0.7
0.001
0.0001
VO = 0.4 V
VCC = 3.3 V
0.6
-50
-25
0
25
50
75
100
125
1.1
1.2
1.3
1.4
1.5
1.6
1.7
TA - TEMPERATURE - °C
VF - FORWARD VOLTAGE - V
Figure 9 Typical Current Transfer Ratio vs. Temperature
Figure 10 Typical Logic High Output Current vs. Temperature
1.1
1
1000
IF = 0 mA
VO = VCC = 3.3 V
100
0.9
10
1
0.8
NORMALIZED
IF = 3 mA
0.7
0.1
0.01
VO = 0.4 V
VCC = 5 V
0.6
-50
-25
0
25
50
75
100
125
-60 -40 -20
0
20
40
60
80 100 120
TA - TEMPERATURE - °C
TA - TEMPERATURE - °C
Figure 11 Typical Logic High Output Current vs. Temperature
1000
IF = 0 mA
VO = VCC = 5 V
100
10
1
0.1
0.01
-60 -40 -20
0
20
40
60
80 100 120
TA - TEMPERATURE - °C
Broadcom
- 14 -
ACPL-M50L, ACPL-054L, ACPL-W50L, ACPL-K54L
Data Sheet
Figure 12 Typical Propagation Delay vs. Temperature
(ACPL-M50L)
Figure 13 Typical Propagation Delay vs. Temperature
(ACPL-054L/W50L/K54L)
800
800
IF = 3 mA, VCC = 3.3 V
IF = 3 mA, VCC = 3.3 V
700
700
RL = 1.9 k:
RL = 1.8 k:
RL = 1.2 k:
600
600
500
500
tPLH
tPLH
400
300
400
300
tPHL
tPHL
200
100
0
200
100
0
-60 -40 -20
0
20
40
60
80 100 120
-60 -40 -20
0
20 40
60 80 100 120
TA - TEMPERATURE - °C
TA - TEMPERATURE - °C
Figure 14 Typical Propagation Delay vs. Temperature
(ACPM-M50L)
Figure 15 Typical Propagation Delay vs. Temperature
(ACPL-054L/W50L/K54L)
800
800
IF = 3 mA, VCC = 5 V
IF = 3 mA, VCC = 5 V
RL = 2.9 k:
700
700
RL = 4.1 k:
RL = 1.9 k:
600
600
500
500
tPLH
tPLH
tPHL
400
400
300
200
100
0
tPHL
300
200
100
0
-60 -40 -20
0
20
40
60
80 100 120
-60 -40 -20
0
20 40
TA - TEMPERATURE - °C
60 80 100 120
TA - TEMPERATURE - °C
Figure 16 Typical Propagation Delay vs. Temperature
(ACPL-M50L)
Figure 17 Typical Propagation Delay vs. Temperature
(ACPL-054L/W50L/K54L)
600
600
IF = 3 mA, VCC = 24 V
IF = 3 mA, VCC = 24 V
RL = 20 k:
RL = 14.8 k:
500
500
400
300
200
100
0
tPHL
RL = 10 k:
tPHL
400
tPLH
tPLH
300
200
100
0
-60 -40 -20
0
20
40
60
80 100 120
-60 -40 -20
0
20 40
60
80 100 120
TA - TEMPERATURE - °C
TA - TEMPERATURE - °C
Broadcom
- 15 -
ACPL-M50L, ACPL-054L, ACPL-W50L, ACPL-K54L
Data Sheet
Figure 18 Typical Propagation Delay vs. Load Resistance
Figure 19 Typical Propagation Delay vs. Load Resistance
1600
1000
IF = 3 mA, VCC = 3.3 V
IF = 3 mA, VCC = 5 V
IF = 10 mA
IF = 3 mA
900
800
700
600
500
400
300
200
100
0
1400
IF = 10 mA
IF = 3 mA
1200
1000
800
tPLH
600
tPLH
tPHL
tPHL
400
200
0
1
10
1
10
RL - LOAD RESISTANCE - k:
RL - LOAD RESISTANCE - k:
Figure 20 Typical Propagation Delay vs. Load Capacitance
(ACPL-M50L)
Figure 21 Typical Propagation Delay vs. Load Capacitance
(ACPL-054L/W50L/K454L)
2600
2400
2600
2400
IF = 3 mA, VCC = 24 V
IF = 3 mA, VCC = 24 V
2200
2000
1800
1600
1400
1200
1000
800
RL = 10 k:, TA = 25°C
2200 RL = 14.8 k:, TA = 25°C
2000
1800
1600
1400
1200
1000
800
600
400
200
0
tPHL
tPLH
tPLH
tPHL
600
400
200
0
0
100
200
300
400
500
0
100
200
300
400
500
CL - LOAD CAPACITANCE - pF
CL - LOAD CAPACITANCE - pF
Figure 22 Typical Propagation Delay vs. Supply Voltage
(ACPL-M50L)
Figure 23 Typical Propagation Delay vs. Supply Voltage
(ACPL-054L/W50L/K54L)
2500
2500
IF = 3 mA
IF = 3 mA
RL = 14.8 k:
RL = 10 k:
2000
1500
1000
500
0
2000
TA = 25°C
TA = 25°C
1500
1000
tPLH
tPLH
tPHL
12
500
0
tPHL
12
8
10
14
16
18
20
22
24
8
10
14
16
18
20
22 24
VCC - SUPPLY VOLTAGE - V
VCC - SUPPLY VOLTAGE - V
Broadcom
- 16 -
ACPL-M50L, ACPL-054L, ACPL-W50L, ACPL-K54L
Data Sheet
Figure 24 Typical Propagation Delay vs. Supply Current
(ACPL-M50L)
Figure 25 Typical Propagation Delay vs. Supply Current
(ACPL-054L/W50L/K54L)
600
600
VCC = 24 V
VCC = 24 V
RL = 10 k:
RL = 14.8 k:
500
400
300
200
100
0
500
400
300
200
100
0
TA = 25°C
TA = 25°C
tPLH
tPLH
tPHL
tPHL
0
5
10
15
20
0
5
10
15
20
IF - FORWARD LED CURRENT - mA
IF - FORWARD LED CURRENT - mA
Figure 26 Switching Test Circuits
IF
0
PULSE
GEN.
IF
V CC
1
3
6
5
4
Z O = 50 :
tr = 5 ns
R L
V CC
V O
V O
0.1μF
V THHL
V THLH
V OL
IF MONITOR
C
L
R M
tPHL
tPLH
Figure 27 Test Circuit for Transient Immunity and Typical Waveforms
10 V
IF
90%
90%
V CM
0 V
V CC
V O
1
3
6
5
4
10%
10%
R L
0.1μF
A
tr
tf
B
V O
V O
V CC
SWITCH AT A: IF = 0 mA
SWITCH AT B: IF = 3 mA
V FF
C
L
V OL
V CM
+
–
PULSE GEN.
Broadcom
- 17 -
Figure 28 Current Transfer Ratio vs. Input Current
Figure 29 DC Pulse Transfer Characteristic
40
250
TA = 25 oC
VCC = 5 V
30
200
VO = 0.4 V
VCC = 5 V
150
20
10
-
100
50
0
IF = 20 mA
IF = 15 mA
IF = 10 mA
IF = 5 mA
0
4
8
12
16
20
24
0
5
10
15
20
25
VO - OUTPUT VOLTAGE - V
IF - FORWARD CURRENT - mA
For product information and a complete list of distributors, please go to our web
site: www.broadcom.com.
Broadcom, the pulse logo, Connecting everything, Avago Technologies, Avago,
and the A logo are among the trademarks of Broadcom and/or its affiliates in the
United States, certain other countries and/or the EU.
Copyright © 2014–2017 by Broadcom. All Rights Reserved.
The term "Broadcom" refers to Broadcom Limited and/or its subsidiaries. For
more information, please visit www.broadcom.com.
Broadcom reserves the right to make changes without further notice to any
products or data herein to improve reliability, function, or design.
Information furnished by Broadcom is believed to be accurate and reliable.
However, Broadcom does not assume any liability arising out of the application
or use of this information, nor the application or use of any product or circuit
described herein, neither does it convey any license under its patent rights nor
the rights of others.
AV02-2223EN – March 10, 2017
相关型号：
©2020 ICPDF网 联系我们和版权申明