YS05S16-D [BEL]
DC-DC Regulated Power Supply Module, 1 Output, 58W, Hybrid,;型号: | YS05S16-D |
厂家: | BEL FUSE INC. |
描述: | DC-DC Regulated Power Supply Module, 1 Output, 58W, Hybrid, |
文件: | 总25页 (文件大小:322K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
YS05S16 DC-DC Converter Data Sheet
3.0-5.5 VDC Input; 0.7525-3.63 VDC Programmable @ 16 A
The
Products: Y-Series
Features
RoHS lead-free solder and lead-solder-exempted
products are available
Delivers up to 16 A (58 W)
No derating up to 85 C
Surface-Mount package
Industry-standard footprint and pinout
Small size and low profile: 1.30” x 0.53” x 0.314”
(33.02 x 13.46 x 7.98 mm)
Weight: 0.22 oz [6.12 g]
Coplanarity less than 0.003”, maximum
Synchronous Buck Converter topology
Start-up into pre-biased output
Applications
Intermediate Bus Architectures
Telecommunications
No minimum load required
Programmable output voltage via external resistor
Operating ambient temperature: -40 °C to 85 °C
Remote output sense
Data communications
Distributed Power Architectures
Servers, workstations
Remote ON/OFF (positive or negative)
Fixed-frequency operation
Auto-reset output overcurrent protection
Auto-reset overtemperature protection
High reliability, MTBF approx. 64.9 Million Hours
calculated per Telcordia TR-332, Method I Case 1
All materials meet UL94, V-0 flammability rating
Benefits
High efficiency – no heat sink required
Reduces total solution board area
Tape and reel packing
Compatible with pick & place equipment
Minimizes part numbers in inventory
UL60950 recognition in U.S. & Canada, and DEMKO
certification per IEC/EN60950
Description
Power-One’s point-of-load converters are recommended for use with regulated bus converters in an Intermediate
Bus Architecture (IBA). The YS05S16 non-isolated DC-DC converter delivers up to 16 A of output current in an
industry-standard surface-mount package. Operating from a 3.0 – 5.5 V input, the YS05S16 converters are ideal
choices for Intermediate Bus Architectures where Point-of-Load (POL) power delivery is generally a requirement.
The converters provide an extremely tight regulated programmable output voltage from 0.7525 V to 3.63 V.
The YS05S16 converters provide exceptional thermal performance, even in high temperature environments with
minimal airflow. No derating is required up to 85 C, even without airflow at natural convection. This performance
is accomplished through the use of advanced circuitry, packaging, and processing techniques to achieve a design
possessing ultra-high efficiency, excellent thermal management, and a very low-body profile.
The low-body profile and the preclusion of heat sinks minimize impedance to system airflow, thus enhancing
cooling for both upstream and downstream devices. The use of 100% automation for assembly, coupled with
advanced power electronics and thermal design, results in a product with extremely high reliability.
MCD10205 Rev. 1.0, 24-Jun-10
Page 1 of 25
www.power-one.com
YS05S16 DC-DC Converter Data Sheet
3.0-5.5 VDC Input; 0.7525-3.63 VDC Programmable @ 16 A
Electrical Specifications
Conditions: TA = 25 ºC, Airflow = 300 LFM (1.5 m/s), Vin = 5 VDC, Vout = 0.7525 – 3.63 V, unless otherwise specified.
Parameter
Notes
Min
Typ
Max Units
Absolute Maximum Ratings
Input Voltage
Continuous
-0.3
-40
-55
6
VDC
°C
Operating Ambient Temperature
Storage Temperature
85
125
°C
Feature Characteristics
Switching Frequency
Full Temperature Range
250
300
3.5
350
3.63
0.5
kHz
VDC
VDC
Output Voltage Trim Range1
Remote Sense Compensation1
By external resistor, See Trim Table 1
Percent of VOUT(NOM)
0.7525
Turn-On Delay Time2
Full resistive load
With Vin = (Converter Enabled, then
Vin applied)
From Vin = Vin(min) to Vo = 0.1* Vo(nom)
3
4.5
ms
With Enable (Vin = Vin(nom)
applied, then enabled)
Rise time2
From enable to Vo = 0.1*Vo(nom)
From 0.1*Vo(nom) to 0.9*Vo(nom)
3
3
3.5
3.5
4.5
5
ms
ms
ON/OFF Control (Positive Logic) 3
Converter Off
-5
0.8
5.5
VDC
VDC
Converter On
2.4
ON/OFF Control (Negative Logic) 3
Converter Off
2.4
-5
5.5
0.8
VDC
VDC
Converter On
Additional Notes:
1
The output voltage should not exceed 3.63 V (taking into account both the programming and remote sense compensation).
Note that startup time is the sum of turn-on delay time and rise time.
The converter is on if ON/OFF pin is left open.
Trim resistor connected across the GND (pin 5) and TRIM (pin 3) pins of the converter.
See waveforms for dynamic response and settling time for different output voltages.
2
3
4
5
MCD10205 Rev. 1.0, 24-Jun-10
Page 2 of 25
www.power-one.com
YS05S16 DC-DC Converter Data Sheet
3.0-5.5 VDC Input; 0.7525-3.63 VDC Programmable @ 16 A
Electrical Specifications (continued)
Conditions: TA = 25 ºC, Airflow = 300 LFM (1.5 m/s), Vin = 5 VDC, Vout = 0.7525 – 3.63 V, unless otherwise specified.
Parameter
Notes
Min
Typ
Max Units
Input Characteristics
Operating Input Voltage Range
Input Undervoltage Lockout
Turn-on Threshold
3.0
5.0
5.5
VDC
Guaranteed by controller
Guaranteed by controller
1.95
1.73
2.05
1.9
2.15
2.07
VDC
VDC
Turn-off Threshold
Maximum Input Current
VIN = 4.5 VDC, IOUT = 16 A
VIN = 3.0 VDC, IOUT = 16 A
VIN = 3.0 VDC, IOUT = 16 A
VIN = 3.0 VDC, IOUT = 16 A
VIN = 3.0 VDC, IOUT = 16 A
VIN = 3.0 VDC, IOUT = 16 A
VIN = 3.0 VDC, IOUT = 16 A
VIN = 3.0 VDC, IOUT = 16 A
VOUT = 3.3 VDC
VOUT = 2.5 VDC
VOUT = 2.0 VDC
VOUT = 1.8 VDC
VOUT = 1.5 VDC
VOUT = 1.2 VDC
VOUT = 1.0 VDC
VOUT = 0.7525 VDC
12.7
15.2
12.4
11.3
9.7
ADC
ADC
ADC
ADC
ADC
ADC
ADC
ADC
mA
8.1
7.0
5.7
Input Stand-by Current (Converter disabled) Vin = 5.0 VDC
3.5
Input No Load Current (Converter enabled)
Vin = 5.5 VDC
mA
mA
mA
mA
mA
mA
mA
mA
VOUT = 3.3 VDC
91
91
87
86
85
76
76
61
20
VOUT = 2.5 VDC
VOUT = 2.0 VDC
VOUT = 1.8 VDC
VOUT = 1.5 VDC
VOUT = 1.2 VDC
VOUT = 1.0 VDC
VOUT = 0.7525 VDC
See Fig. G for setup (BW = 20 MHz)
Input Reflected-Ripple Current - is
mAP-P
MCD10205 Rev. 1.0, 24-Jun-10
Page 3 of 25
www.power-one.com
YS05S16 DC-DC Converter Data Sheet
3.0-5.5 VDC Input; 0.7525-3.63 VDC Programmable @ 16 A
Electrical Specifications (continued)
Conditions: TA = 25 ºC, Airflow = 300 LFM (1.5 m/s), Vin = 5 VDC, Vout = 0.7525 – 3.63 V, unless otherwise specified.
Parameter
Notes
Min
Typ
Max Units
Output Characteristics
-1.5
Vout
+1.5
%Vout
Output Voltage Set Point (no load)
Output Regulation4
Over Line
Full resistive load
From no load to full load
0.75
0.75
1
1
%Vout
%Vout
Over Load
Output Voltage Range
(Over all operating input voltage, resistive load
and temperature conditions until end of life )
-3
+3
%Vout
Output Ripple and Noise – 20 MHz bandwidth Over line, load and temperature (Fig. G)
mVP-P
mVP-P
Peak-to-Peak
Peak-to-Peak
VOUT = 3.3 VDC
30
10
60
20
VOUT = 0.7525 VDC
Plus full load (resistive)
External Load Capacitance
Min ESR > 1 mΩ
μF
μF
1,000
5,000
16
Min ESR > 10 mΩ
Output Current Range
A
0
18
2
Output Current Limit Inception (IOUT
)
A
28
4
38
Arms
Output Short-Circuit Current (Hiccup mode)
Short = 10 mꢀ, continuous
8
Dynamic Response
50% Load current change from
8 A -16 A - 8 A with di/dt = 5 A/μs
Co = 100 μF tant. + 1 μF ceramic
1505
60
mV
µs
Settling Time (VOUT < 10% peak deviation)
Efficiency
Full load (16 A)
VOUT = 3.3 VDC
VOUT = 2.5 VDC
VOUT = 2.0 VDC
VOUT = 1.8 VDC
VOUT = 1.5 VDC
VOUT = 1.2 VDC
VOUT = 1.0 VDC
VOUT = 0.7525 VDC
93.0
90.5
88.5
87.5
86.0
83.5
81.5
77.5
%
%
%
%
%
%
%
%
MCD10205 Rev. 1.0, 24-Jun-10
Page 4 of 25
www.power-one.com
YS05S16 DC-DC Converter Data Sheet
3.0-5.5 VDC Input; 0.7525-3.63 VDC Programmable @ 16 A
Operations
Input and Output Impedance
32
The YS05S16 converter should be connected via a
low impedance to the DC power source. In many
applications, the inductance associated with the
distribution from the power source to the input of the
converter can affect the stability of the converter.
The use of decoupling capacitors is recommended in
order to ensure stability of the converter and reduce
input ripple voltage. Internally, the converter has
44 μF (low ESR ceramics) of input capacitance.
28
24
20
16
12
8
Vin = 3.3V
Vin = 5.0V
4
In a typical application, low - ESR tantalum or POS
capacitors will be sufficient to provide adequate
ripple voltage filtering at the input of the converter.
However, very low ESR ceramic capacitors
100 - 200 μF are recommended at the input of the
converter in order to minimize the input ripple
voltage. They should be placed as close as possible
to the input pins of the converter.
0
0
1
2
3
4
Vout [V]
Fig. B: Input Voltage Ripple, CIN = 470 μF polymer + 2 x 47 μF
ceramic.
ON/OFF (Pin 1)
The ON/OFF pin is used to turn the power converter
on or off remotely via a system signal. There are two
remote control options available, positive logic
(standard option) and negative logic, with both
referenced to GND. The typical connections are
shown in Fig. C.
The YS05S16 has been designed for stable
operation with or without external capacitance. Low
ESR ceramic capacitors placed as close as possible
to the load (minimum 100 μF) are recommended for
improved transient performance and lower output
voltage ripple.
To turn the converter on the ON/OFF pin should be
at a logic low or left open, and to turn the converter
off the ON/OFF pin should be at a logic high or
connected to Vin. See the Electrical Specifications
for logic high/low definitions.
It is important to keep low resistance and low
inductance PCB traces for connecting load to the
output pins of the converter in order to maintain good
load regulation.
Fig. A shows input voltage ripple for various output
voltages using four 47 μF input ceramic capacitors.
The same plot is shown in Fig. B with one 470 μF
polymer capacitor (6TPB470M from Sanyo) in
parallel with two 47 μF ceramic capacitors at full
load.
Y-Series
Converter
Vin
SENSE
Vout
R*
(Top View)
ON/OFF
Vin
Rload
24
20
16
12
8
GND
TRIM
CONTROL
INPUT
R* is for negative logic option only
Fig. C: Circuit configuration for ON/OFF function.
The positive logic version turns the converter on
when the ON/OFF pin is at a logic high or left open,
and turns the converter off when at a logic low or
shorted to GND.
Vin = 3.3V
Vin = 5.0V
4
0
The negative logic version turns the converter on
when the ON/OFF pin is at logic low or left open, and
turns the converter off when the ON/OFF pin is at a
logic high or connected to Vin.
0
1
2
3
4
Vout [V]
Fig. A: Input Voltage Ripple, CIN = 4 x 47 μF ceramic, full load.
MCD10205 Rev. 1.0, 24-Jun-10
Page 5 of 25
www.power-one.com
YS05S16 DC-DC Converter Data Sheet
3.0-5.5 VDC Input; 0.7525-3.63 VDC Programmable @ 16 A
The ON/OFF pin is internally pulled up to Vin for
equal to the product of the nominal output voltage
and the allowable output current for the given
conditions.
positive logic version, and pulled down for a negative
logic version. A TTL or CMOS logic gate, open-
collector (open-drain) transistor can be used to drive
ON/OFF pin. This device must be capable of:
When using remote sense, the output voltage at the
converter can be increased up to 0.5 V above the
nominal rating in order to maintain the required
voltage across the load. Therefore, the designer
must, if necessary, decrease the maximum current
(originally obtained from the derating curves) by the
same percentage to ensure the converter’s actual
output power remains at or below the maximum
allowable output power.
– sinking up to 1.2 mA at a low level voltage of
0.8 V
– sourcing up to 0.25 mA at a high logic level of
2.3 V - 5.5 V.
When using open-collector (open-drain) transistor
with a negative logic option, add a pull-up resistor
(R*) to Vin as shown in Fig. C:
Output Voltage Programming (Pin 3)
– 20 K, if the minimum Vin is 4.5 V
– 10 K, if the minimum Vin is 3.0 V
The output voltage can be programmed from
0.7525 V to 3.63 V by connecting an external resistor
between TRIM pin (Pin 3) and GND pin (Pin 5); see
Fig. E. Note that when a trim resistor is not
connected, the output voltage of the converter is
0.7525 V.
– 5 K, if the undervoltage shutdown at 2.05 - 2.15 V
is required.
Remote Sense (Pin 2)
The remote sense feature of the converter
compensates for voltage drops occurring only
between Vout pin (Pin 4) of the converter and the
load. The SENSE (Pin 2) pin should be connected at
the load or at the point where regulation is required
(see Fig. D). There is no sense feature on the output
GND return pin, where the solid ground plane should
provide a low voltage drop.
Y-Series
Converter
SENSE
Vout
Vin
(Top View)
ON/OFF
Vin
Rload
TRIM
GND
RTRIM
Y-Series
Converter
SENSE
Vout
Vin
Fig. E: Configuration for programming output voltage.
Rw
(Top View)
ON/OFF
Vin
A trim resistor, RTRIM, for a desired output voltage
can be calculated using the following equation:
Rload
TRIM
GND
21.07
RTRIM
5.11
[kꢀ]
(VO-REQ - 0.7525)
Rw
Fig. D: Remote sense circuit configuration.
where,
RTRIM Required value of trim resistor [kꢀ]
VOREQ Desired (trimmed) output voltage [V]
If remote sensing is not required, the SENSE pin
must be connected to the Vout pin (Pin 4) to ensure
the converter will regulate at the specified output
voltage. If these connections are not made, the
converter will deliver an output voltage that is slightly
higher than the specified value.
Note that the tolerance of a trim resistor directly
affects the output voltage tolerance. It is
recommended to use standard 1% or 0.5% resistors;
for tighter tolerance, two resistors in parallel are
recommended rather than one standard value from
Table 1.
Because the sense lead carries minimal current,
large trace on the end-user board are not required.
However, sense trace should be located close to a
ground plane to minimize system noise and ensure
optimum performance.
Ground pin of the trim resistor should be connected
directly to the converter GND pin (Pin 5) with no
voltage drop in between. Table 1 provides the trim
resistor values for popular output voltages.
When utilizing the remote sense feature, care must
be taken not to exceed the maximum allowable
output power capability of the converter, which is
MCD10205 Rev. 1.0, 24-Jun-10
Page 6 of 25
www.power-one.com
YS05S16 DC-DC Converter Data Sheet
3.0-5.5 VDC Input; 0.7525-3.63 VDC Programmable @ 16 A
Protection Features
Input Undervoltage Lockout
Table 1: Trim Resistor Value
The Closest
Standard Value [kΩ]
V0-REG [V]
RTRIM [kΩ]
Input undervoltage lockout is standard with this
converter. The converter will shut down when the
input voltage drops below a pre-determined voltage;
it will start automatically when Vin returns to a
specified range.
0.7525
1.0
open
80.0
41.97
23.1
15
80.6
42.2
23.2
15
1.2
1.5
The input voltage must be typically 2.05 V for the
converter to turn on. Once the converter has been
turned on, it will shut off when the input voltage
drops below typically 1.9 V.
1.8
2.0
11.78
6.95
3.16
2.21
11.8
6.98
3.16
2.21
2.5
3.3
Output Overcurrent Protection (OCP)
3.63
The converter is protected against overcurrent and
short circuit conditions. Upon sensing an overcurrent
condition, the converter will enter hiccup mode. Once
over-load or short circuit condition is removed, Vout
will return to nominal value.
The output voltage can also be programmed by
external voltage source. To make trimming less
sensitive,
a
series external resistor Rext is
recommended between TRIM pin and programming
voltage source. Control Voltage can be calculated by
the formula:
Overtemperature Protection (OTP)
The converter will shut down under an
overtemperature condition to protect itself from
overheating caused by operation outside the thermal
derating curves, or operation in abnormal conditions
such as system fan failure. After the converter has
cooled to a safe operating temperature, it will
automatically restart.
(5.11 REXT)(VO-REQ - 0.7525)
V
CTRL 0.7
[V]
30.1
where,
VCTRL Control voltage [V]
REXT External resistor between TRIM pin and
voltage source; the value can be chosen depending
on the required output voltage range [kꢀ].
Safety Requirements
The converter meets North American and
International safety regulatory requirements per
UL60950 and EN60950. The maximum DC voltage
between any two pins is Vin under all operating
conditions. Therefore, the unit has ELV (extra low
voltage) output; it meets SELV requirements under
the condition that all input voltages are ELV.
Control voltages with REXT 0 and REXT 15K are
shown in Table 2.
Table 2: Control Voltage [VDC]
V0-REG [V] VCTRL (REXT = 0)
VCTRL(REXT = 15K)
0.7525
1.0
0.700
0.658
0.624
0.573
0.522
0.488
0.403
0.268
0.257
0.700
0.535
0.401
0.201
-0.000
-0.133
-0.468
-1.002
-1.044
The converter is not internally fused. To comply with
safety agencies’ requirements, a recognized fuse
with a maximum rating of 20 Amps must be used in
series with the input line.
1.2
1.5
1.8
2.0
Characterization
2.5
General Information
3.3
3.63
The converter has been characterized for many
operational aspects, to include thermal derating
(maximum load current as a function of ambient
temperature and airflow) for vertical and horizontal
mountings, efficiency, startup and shutdown
parameters, output ripple and noise, transient
response to load step-change, overload, and short
circuit.
MCD10205 Rev. 1.0, 24-Jun-10
Page 7 of 25
www.power-one.com
YS05S16 DC-DC Converter Data Sheet
3.0-5.5 VDC Input; 0.7525-3.63 VDC Programmable @ 16 A
The figures are numbered as Fig. x.y, where x
temperature was varied between 25 °C and 85 °C,
with airflow rates from 30 to 500 LFM (0.15 m/s to
2.5 m/s), and vertical and horizontal mountings. The
airflow during the testing is parallel to the short axis
of the converter, going from pin 1 and pin 6 to
pins 2–5.
indicates the different output voltages, and y
associates with specific plots (y = 1 for the vertical
thermal derating, …). For example, Fig. x.1 will refer
to the vertical thermal derating for all the output
voltages in general.
The following pages contain specific plots or
waveforms associated with the converter. Additional
comments for specific data are provided below.
For each set of conditions, the maximum load
current is defined as the lowest of:
(i) The output current at which any MOSFET
temperature does not exceed a maximum specified
temperature (120°C) as indicated by the
thermographic image, or
Test Conditions
All data presented were taken with the converter
soldered to a test board, specifically a 0.060” thick
printed wiring board (PWB) with four layers. The top
and bottom layers were not metalized. The two inner
layers, comprised of two-ounce copper, were used to
provide traces for connectivity to the converter.
(ii) The maximum current rating of the converter
(16 A).
During normal operation, derating curves with
maximum FET temperature less than or equal to
120 °C should not be exceeded. Temperature on the
PCB at the thermocouple location shown in Fig. F
should not exceed 120 °C in order to operate inside
the derating curves.
The lack of metalization on the outer layers as well
as the limited thermal connection ensured that heat
transfer from the converter to the PWB was
minimized. This provides a worst-case but consistent
scenario for thermal derating purposes.
Efficiency
All measurements requiring airflow were made in the
vertical and horizontal wind tunnels using Infrared
Fig. x.3 shows the efficiency vs. load current plot for
ambient temperature of 25 ºC, airflow rate of
200 LFM (1 m/s) and input voltages of 4.5 V, 5.0 V
and 5.5 V. Fig. x.4 is for input voltages of 3.0 V,
3.3 V and 3.6 V and output voltages ≤ 2.5 V.
(IR)
thermography
and
thermocouples
for
thermometry.
Ensuring components on the converter do not
exceed their ratings is important to maintaining high
reliability. If one anticipates operating the converter
at or close to the maximum loads specified in the
derating curves, it is prudent to check actual
Power Dissipation
Fig. 3.3V.4 shows the power dissipation vs. load
current plot for Ta = 25 ºC, airflow rate of 200 LFM
(1 m/s) with vertical mounting and input voltages of
4.5 V, 5.0 V and 5.5 V for 3.3 V output.
operating
temperatures
in
the
application.
Thermographic imaging is preferable; if this
capability is not available, then thermocouples may
be used. . The use of AWG #40 gauge thermocouple
is recommended to ensure measurement accuracy.
Careful routing of the thermocouple leads will further
minimize measurement error. Refer to Fig. F for the
optimum measuring thermocouple location.
Ripple and Noise
The output voltage ripple waveform is measured at
full rated load current. Note that all output voltage
waveforms are measured across a 1 μF ceramic
capacitor.
The output voltage ripple and input reflected-ripple
current waveforms are obtained using the test setup
shown in Fig. G.
iS
1 H
source
inductance
Y-Series
CO
1F
CIN
ceramic
capacitor
100F
ceramic
capacitor
Vout
DC-DC
Converter
4x47F
ceramic
capacitor
Fig. F: Location of the thermocouple for thermal testing.
Vsource
Thermal Derating
Load current vs. ambient temperature and airflow
rates are given in Figs. x.1 and Figs. x.2 for
Fig. G: Test setup for measuring input reflected-ripple currents, is
and output voltage ripple.
maximum
temperature
of
120°C.
Ambient
MCD10205 Rev. 1.0, 24-Jun-10
Page 8 of 25
www.power-one.com
YS05S16 DC-DC Converter Data Sheet
3.0-5.5 VDC Input; 0.7525-3.63 VDC Programmable @ 16 A
20
16
12
8
20
16
12
500 LFM (2.5 m/s)
400 LFM (2.0 m/s)
300 LFM (1.5 m/s)
200 LFM (1.0 m/s)
100 LFM (0.5 m/s)
30 LFM (0.15 m/s)
500 LFM (2.5 m/s)
400 LFM (2.0 m/s)
300 LFM (1.5 m/s)
200 LFM (1.0 m/s)
100 LFM (0.5 m/s)
8
4
4
30 LFM (0.15 m/s)
0
0
20
30
40
50
60
70
80
90
20
30
40
50
60
70
80
90
Ambient Temperature [°C]
Ambient Temperature [°C]
Fig. 3.3V.1: Available load current vs. ambient temperature and
airflow rates for Vout = 3.3 V converter mounted vertically with Vin
= 5 V, and maximum MOSFET temperature 120 C.
Fig. 3.3V.2: Available load current vs. ambient temperature and
airflow rates for Vout = 3.3 V converter mounted horizontally with
Vin = 5 V, and maximum MOSFET temperature 120 C.
5
4
3
2
1.00
0.95
0.90
0.85
5.5 V
5.0 V
4.5 V
5.5 V
5.0 V
4.5 V
1
0.80
0.75
0
0
3
6
9
12
15
18
0
3
6
9
12
15
18
Load Current [Adc]
Load Current [Adc]
Fig. 3.3V.4: Power loss vs. load current and input voltage for Vout
= 3.3 V converter mounted vertically with air flowing at a rate of
200 LFM (1 m/s) and Ta = 25 C.
Fig. 3.3V.3: Efficiency vs. load current and input voltage for Vout
= 3.3 V converter mounted vertically with air flowing at a rate of
200 LFM (1 m/s) and Ta = 25 C.
MCD10205 Rev. 1.0, 24-Jun-10
Page 9 of 25
www.power-one.com
YS05S16 DC-DC Converter Data Sheet
3.0-5.5 VDC Input; 0.7525-3.63 VDC Programmable @ 16 A
Fig. 3.3V.5: Turn-on transient for Vout = 3.3 V with application of
Fig. 3.3V.6: Output voltage ripple (20 mV/div.) at full rated load
current into a resistive load with external capacitance 100 μF
ceramic + 1 μF ceramic and Vin = 5 V for Vout = 3.3 V. Time
scale: 2 μs/div.
Vin at full rated load current (resistive) and 100 μF external
capacitance at Vin = 5 V. Top trace: Vin (5 V/div.); Bottom trace:
output voltage (1 V/div.); Time scale: 2 ms/div.
Fig. 3.3V.7: Output voltage for Vout = 3.3 V to positive load
current step change from 8 A to 16 A with slew rate of 5 A/μs at
Vin = 5 V. Top trace: output voltage (100 mV/div.); Bottom trace:
load current (5 A/div.). Co = 100 μF ceramic. Time scale: 20
μs/div.
Fig. 3.3V.8: Output voltage response for Vout = 3.3 V to negative
load current step change from 16 A to 8 A with slew rate of -5 A/μs
at Vin = 5 V. Top trace: output voltage (100 mV/div.); Bottom
trace: load current (5 A/div.). Co = 100 μF ceramic. Time scale:
20 μs/div.
MCD10205 Rev. 1.0, 24-Jun-10
Page 10 of 25
www.power-one.com
YS05S16 DC-DC Converter Data Sheet
3.0-5.5 VDC Input; 0.7525-3.63 VDC Programmable @ 16 A
20
16
12
8
20
16
12
500 LFM (2.5 m/s)
400 LFM (2.0 m/s)
300 LFM (1.5 m/s)
200 LFM (1.0 m/s)
100 LFM (0.5 m/s)
30 LFM (0.15 m/s)
500 LFM (2.5 m/s)
400 LFM (2.0 m/s)
300 LFM (1.5 m/s)
200 LFM (1.0 m/s)
100 LFM (0.5 m/s)
8
4
4
30 LFM (0.15 m/s)
0
0
20
30
40
50
60
70
80
90
20
30
40
50
60
70
80
90
Ambient Temperature [°C]
Ambient Temperature [°C]
Fig. 2.5V.1: Available load current vs. ambient temperature and
airflow rates for Vout = 2.5 V converter mounted vertically with Vin
= 5 V, and maximum MOSFET temperature 120 C.
Fig. 2.5V.2: Available load current vs. ambient temperature and
airflow rates for Vout = 2.5 V converter mounted horizontally with
Vin = 5 V, and maximum MOSFET temperature 120 C.
1.00
0.95
0.90
0.85
1.00
0.95
0.90
0.85
3.6 V
3.3 V
3.0 V
5.5 V
5.0 V
4.5 V
0.80
0.75
0.80
0.75
0
3
6
9
12
15
18
0
3
6
9
12
15
18
Load Current [Adc]
Load Current [Adc]
Fig. 2.5V.4: Efficiency vs. load current and input voltage for Vout
= 2.5 V converter mounted vertically with air flowing at a rate of
200 LFM (1 m/s) and Ta = 25 C.
Fig. 2.5V.3: Efficiency vs. load current and input voltage for Vout
= 2.5 V converter mounted vertically with air flowing at a rate of
200 LFM (1 m/s) and Ta = 25 C.
MCD10205 Rev. 1.0, 24-Jun-10
Page 11 of 25
www.power-one.com
YS05S16 DC-DC Converter Data Sheet
3.0-5.5 VDC Input; 0.7525-3.63 VDC Programmable @ 16 A
Fig. 2.5V.5: Turn-on transient for Vout = 2.5 V with application of
Fig. 2.5V.6: Output voltage ripple (20 mV/div.) at full rated load
current into a resistive load with external capacitance 100 μF
ceramic + 1 μF ceramic and Vin = 5 V for Vout = 2.5 V. Time
scale: 2 μs/div.
Vin at full rated load current (resistive) and 100 μF external
capacitance at Vin = 5 V. Top trace: Vin (5 V/div.); Bottom trace:
output voltage (1 V/div.); Time scale: 2 ms/div.
Fig. 2.5V.7: Output voltage response for Vout = 2.5 V to positive
load current step change from 8 A to 16 A with slew rate of 5 A/μs
at Vin = 5 V. Top trace: output voltage (100 mV/div.); Bottom
trace: load current (5 A/div.). Co = 100 μF ceramic. Time scale:
20 μs/div.
Fig. 2.5V.8: Output voltage response for Vout = 2.5 V to negative
load current step change from 16 A to 8 A with slew rate of -5 A/μs
at Vin = 5 V. Top trace: output voltage (100 mV/div.); Bottom
trace: load current (5 A/div.). Co = 100 μF ceramic. Time scale:
20 μs/div.
MCD10205 Rev. 1.0, 24-Jun-10
Page 12 of 25
www.power-one.com
YS05S16 DC-DC Converter Data Sheet
3.0-5.5 VDC Input; 0.7525-3.63 VDC Programmable @ 16 A
20
16
12
8
20
16
12
500 LFM (2.5 m/s)
400 LFM (2.0 m/s)
300 LFM (1.5 m/s)
200 LFM (1.0 m/s)
100 LFM (0.5 m/s)
30 LFM (0.15 m/s)
500 LFM (2.5 m/s)
400 LFM (2.0 m/s)
300 LFM (1.5 m/s)
200 LFM (1.0 m/s)
100 LFM (0.5 m/s)
8
4
4
30 LFM (0.15 m/s)
0
0
20
30
40
50
60
70
80
90
20
30
40
50
60
70
80
90
Ambient Temperature [°C]
Ambient Temperature [°C]
Fig. 2.0V.1: Available load current vs. ambient temperature and
airflow rates for Vout = 2.0 V converter mounted vertically with Vin
= 5 V, and maximum MOSFET temperature 120 C.
Fig. 2.0V.2: Available load current vs. ambient temperature and
airflow rates for Vout = 2.0 V converter mounted horizontally with
Vin = 5 V, and maximum MOSFET temperature 120 C.
0.95
0.90
0.85
0.80
0.95
0.90
0.85
0.80
3.6 V
3.3 V
3.0 V
5.5 V
5.0 V
4.5 V
0.75
0.70
0.75
0.70
0
3
6
9
12
15
18
0
3
6
9
12
15
18
Load Current [Adc]
Load Current [Adc]
Fig. 2.0V.4: Efficiency vs. load current and input voltage for Vout
= 2.0 V converter mounted vertically with air flowing at a rate of
200 LFM (1 m/s) and Ta = 25 C.
Fig. 2.0V.3: Efficiency vs. load current and input voltage for Vout
= 2.0 V converter mounted vertically with air flowing at a rate of
200 LFM (1 m/s) and Ta = 25 C.
MCD10205 Rev. 1.0, 24-Jun-10
Page 13 of 25
www.power-one.com
YS05S16 DC-DC Converter Data Sheet
3.0-5.5 VDC Input; 0.7525-3.63 VDC Programmable @ 16 A
Fig. 2.0V.5: Turn-on transient for Vout = 2.0 V with application of
Fig. 2.0V.6: Output voltage ripple (20 mV/div.) at full rated load
current into a resistive load with external capacitance 100 μF
ceramic + 1 μF ceramic and Vin = 5 V for Vout = 2.0 V. Time
scale: 2 μs/div.
Vin at full rated load current (resistive) and 100μF external
capacitance at Vin = 5 V. Top trace: Vin (5 V/div.); Bottom trace:
output voltage (1 V/div.); Time scale: 2 ms/div.
Fig. 2.0V.7: Output voltage response for Vout = 2.0 V to positive
load current step change from 8 A to 16 A with slew rate of 5 A/μs
at Vin = 5 V. Top trace: output voltage (100 mV/div.); Bottom
trace: load current (5 A/div.). Co = 100 μF ceramic. Time scale:
20 μs/div.
Fig. 2.0V.8: Output voltage response for Vout = 2.0
V to negative load current step change from 16 A to
8 A with slew rate of -5 A/μs at Vin = 5 V. Top trace:
output voltage (100 mV/div.); Bottom trace: load
current (5 A/div.). Co = 100 μF ceramic. Time scale:
20 μs/div.
MCD10205 Rev. 1.0, 24-Jun-10
Page 14 of 25
www.power-one.com
YS05S16 DC-DC Converter Data Sheet
3.0-5.5 VDC Input; 0.7525-3.63 VDC Programmable @ 16 A
20
16
12
8
20
16
12
500 LFM (2.5 m/s)
400 LFM (2.0 m/s)
300 LFM (1.5 m/s)
200 LFM (1.0 m/s)
100 LFM (0.5 m/s)
30 LFM (0.15 m/s)
500 LFM (2.5 m/s)
400 LFM (2.0 m/s)
300 LFM (1.5 m/s)
200 LFM (1.0 m/s)
100 LFM (0.5 m/s)
8
4
4
30 LFM (0.15 m/s)
0
0
20
30
40
50
60
70
80
90
20
30
40
50
60
70
80
90
Ambient Temperature [°C]
Ambient Temperature [°C]
Fig. 1.8V.1: Available load current vs. ambient temperature and
airflow rates for Vout = 1.8 V converter mounted vertically with Vin
= 5 V, and maximum MOSFET temperature 120 C.
Fig. 1.8V.2: Available load current vs. ambient temperature and
airflow rates for Vout = 1.8 V converter mounted horizontally with
Vin = 5 V, and maximum MOSFET temperature 120 C.
0.95
0.90
0.85
0.80
0.95
0.90
0.85
0.80
3.6 V
3.3 V
3.0 V
5.5 V
5.0 V
4.5 V
0.75
0.70
0.75
0.70
0
3
6
9
12
15
18
0
3
6
9
12
15
18
Load Current [Adc]
Load Current [Adc]
Fig. 1.8V.4: Efficiency vs. load current and input voltage for Vout
= 1.8 V converter mounted vertically with air flowing at a rate of
200 LFM (1 m/s) and Ta = 25 C.
Fig. 1.8V.3: Efficiency vs. load current and input voltage for Vout
= 1.8 V converter mounted vertically with air flowing at a rate of
200 LFM (1 m/s) and Ta = 25 C.
MCD10205 Rev. 1.0, 24-Jun-10
Page 15 of 25
www.power-one.com
YS05S16 DC-DC Converter Data Sheet
3.0-5.5 VDC Input; 0.7525-3.63 VDC Programmable @ 16 A
Fig. 1.8V.5: Turn-on transient for Vout = 1.8 V with application of
Fig. 1.8V.6: Output voltage ripple (20 mV/div.) at full rated load
current into a resistive load with external capacitance 100 μF
ceramic + 1 μF ceramic and Vin = 5 V for Vout = 1.8 V. Time
scale: 2 μs/div.
Vin at full rated load current (resistive) and 100μF external
capacitance at Vin = 5 V. Top trace: Vin (5 V/div.); Bottom trace:
output voltage (1V/div.); Time scale: 2 ms/div.
Fig. 1.8V.8: Output voltage response for Vout = 1.8 V to negative
load current step change from 16 A to 8 A with slew rate of -5 A/μs
at Vin = 5 V. Top trace: output voltage (100 mV/div.); Bottom
trace: load current (5 A/div.). Co = 100 μF ceramic. Time scale:
20 μs/div.
Fig. 1.8V.7: Output voltage response for Vout = 1.8 V to positive
load current step change from 8 A to 16 A with slew rate of 5 A/μs
at Vin = 5 V. Top trace: output voltage (100 mV/div.); Bottom
trace: load current (5 A/div.). Co = 100 μF ceramic. Time scale:
20 μs/div.
MCD10205 Rev. 1.0, 24-Jun-10
Page 16 of 25
www.power-one.com
YS05S16 DC-DC Converter Data Sheet
3.0-5.5 VDC Input; 0.7525-3.63 VDC Programmable @ 16 A
20
16
12
8
20
16
12
500 LFM (2.5 m/s)
400 LFM (2.0 m/s)
300 LFM (1.5 m/s)
200 LFM (1.0 m/s)
100 LFM (0.5 m/s)
30 LFM (0.15 m/s)
500 LFM (2.5 m/s)
400 LFM (2.0 m/s)
300 LFM (1.5 m/s)
200 LFM (1.0 m/s)
100 LFM (0.5 m/s)
8
4
4
30 LFM (0.15 m/s)
0
0
20
30
40
50
60
70
80
90
20
30
40
50
60
70
80
90
Ambient Temperature [°C]
Ambient Temperature [°C]
Fig. 1.5V.1: Available load current vs. ambient temperature and
airflow rates for Vout = 1.5 V converter mounted vertically with Vin
= 5 V, and maximum MOSFET temperature 120 C.
Fig. 1.5V.2: Available load current vs. ambient temperature and
airflow rates for Vout = 1.5 V converter mounted horizontally with
Vin = 5 V, and maximum MOSFET temperature 120 C.
0.95
0.90
0.85
0.80
0.95
0.90
0.85
0.80
3.6 V
3.3 V
3.0 V
5.5 V
5.0 V
4.5 V
0.75
0.70
0.75
0.70
0
3
6
9
12
15
18
0
3
6
9
12
15
18
Load Current [Adc]
Load Current [Adc]
Fig. 1.5V.4: Efficiency vs. load current and input voltage for Vout
= 1.5 V converter mounted vertically with air flowing at a rate of
200 LFM (1 m/s) and Ta = 25 C.
Fig. 1.5V.3: Efficiency vs. load current and input voltage for Vout
= 1.5 V converter mounted vertically with air flowing at a rate of
200 LFM (1 m/s) and Ta = 25 C.
MCD10205 Rev. 1.0, 24-Jun-10
Page 17 of 25
www.power-one.com
YS05S16 DC-DC Converter Data Sheet
3.0-5.5 VDC Input; 0.7525-3.63 VDC Programmable @ 16 A
Fig. 1.5V.5: Turn-on transient for Vout = 1.5 V with application of
Fig. 1.5V.6: Output voltage ripple (20 mV/div.) at full rated load
current into a resistive load with external capacitance 100 μF
ceramic + 1 μF ceramic and Vin = 5 V for Vout = 1.5 V. Time
scale: 2 μs/div.
Vin at full rated load current (resistive) and 100 μF external
capacitance at Vin = 5 V. Top trace: Vin (5 V/div.); Bottom trace:
output voltage (1 V/div.); Time scale: 2 ms/div.
Fig. 1.5V.7: Output voltage response for Vout = 1.5 V to positive
load current step change from 8 A to 16 A with slew rate of 5 A/μs
at Vin = 5V. Top trace: output voltage (100 mV/div.); Bottom trace:
load current (5 A/div.). Co = 100 μF ceramic. Time scale:
20 μs/div.
Fig. 1.5V.8: Output voltage response for Vout = 1.5 V to negative
load current step change from 16 A to 8 A with slew rate of -5 A/μs
at Vin = 5 V. Top trace: output voltage (100 mV/div.); Bottom
trace: load current (5 A/div.). Co = 100 μF ceramic. Time scale:
20 μs/div.
MCD10205 Rev. 1.0, 24-Jun-10
Page 18 of 25
www.power-one.com
YS05S16 DC-DC Converter Data Sheet
3.0-5.5 VDC Input; 0.7525-3.63 VDC Programmable @ 16 A
20
16
12
8
20
16
12
500 LFM (2.5 m/s)
400 LFM (2.0 m/s)
300 LFM (1.5 m/s)
200 LFM (1.0 m/s)
100 LFM (0.5 m/s)
30 LFM (0.15 m/s)
500 LFM (2.5 m/s)
400 LFM (2.0 m/s)
300 LFM (1.5 m/s)
200 LFM (1.0 m/s)
100 LFM (0.5 m/s)
8
4
4
30 LFM (0.15 m/s)
0
0
20
30
40
50
60
70
80
90
20
30
40
50
60
70
80
90
Ambient Temperature [°C]
Ambient Temperature [°C]
Fig. 1.2V.1: Available load current vs. ambient temperature and
airflow rates for Vout = 1.2 V converter mounted vertically with Vin
= 5 V, and maximum MOSFET temperature 120 C.
Fig. 1.2V.2: Available load current vs. ambient temperature and
airflow rates for Vout = 1.2 V converter mounted horizontally with
Vin = 5 V, and maximum MOSFET temperature 120 C.
0.90
0.85
0.80
0.75
0.90
0.85
0.80
0.75
3.6 V
3.3 V
3.0 V
5.5 V
5.0 V
4.5 V
0.70
0.70
0.65
0.65
0
3
6
9
12
15
18
0
3
6
9
12
15
18
Load Current [Adc]
Load Current [Adc]
Fig. 1.2V.4: Efficiency vs. load current and input voltage for Vout
= 1.2 V converter mounted vertically with air flowing at a rate of
200 LFM (1 m/s) and Ta = 25 C.
Fig. 1.2V.3: Efficiency vs. load current and input voltage for Vout
= 1.2 V converter mounted vertically with air flowing at a rate of
200 LFM (1 m/s) and Ta = 25 C.
MCD10205 Rev. 1.0, 24-Jun-10
Page 19 of 25
www.power-one.com
YS05S16 DC-DC Converter Data Sheet
3.0-5.5 VDC Input; 0.7525-3.63 VDC Programmable @ 16 A
Fig. 1.2V.6: Output voltage ripple (20 mV/div.) at full rated load
Fig. 1.2V.5: Turn-on transient for Vout = 1.2 V with application of
current into a resistive load with external capacitance 100 μF
ceramic + 1 μF ceramic and Vin = 5 V for Vout = 1.2 V. Time
scale: 2 μs/div.
Vin at full rated load current (resistive) and 100 μF external
capacitance at Vin = 5 V. Top trace: Vin (5 V/div.); Bottom trace:
output voltage (1 V/div.); Time scale: 2 ms/div.
Fig. 1.2V.8: Output voltage response for Vout = 1.2 V to negative
load current step change from 16 A to 8 A with slew rate of -5 A/μs
at Vin = 5 V. Top trace: output voltage (100 mV/div.); Bottom
trace: load current (5 A/div.). Co = 100 μF ceramic. Time scale:
20 μs/div.
Fig. 1.2V.6: Output voltage response for Vout = 1.2 V to positive
load current step change from 8 A to 16 A with slew rate of 5 A/μs
at Vin = 5 V. Top trace: output voltage (100 mV/div.); Bottom
trace: load current (5 A/div.). Co = 100 μF ceramic. Time scale:
20 μs/div.
MCD10205 Rev. 1.0, 24-Jun-10
Page 20 of 25
www.power-one.com
YS05S16 DC-DC Converter Data Sheet
3.0-5.5 VDC Input; 0.7525-3.63 VDC Programmable @ 16 A
20
16
12
8
20
16
12
500 LFM (2.5 m/s)
400 LFM (2.0 m/s)
300 LFM (1.5 m/s)
200 LFM (1.0 m/s)
100 LFM (0.5 m/s)
30 LFM (0.15 m/s)
500 LFM (2.5 m/s)
400 LFM (2.0 m/s)
300 LFM (1.5 m/s)
200 LFM (1.0 m/s)
100 LFM (0.5 m/s)
8
4
4
30 LFM (0.15 m/s)
0
0
20
30
40
50
60
70
80
90
20
30
40
50
60
70
80
90
Ambient Temperature [°C]
Ambient Temperature [°C]
Fig. 1.0V.1: Available load current vs. ambient temperature and
airflow rates for Vout = 1.0 V converter mounted vertically with Vin
= 5 V, and maximum MOSFET temperature 120 C.
Fig. 1.0V.2: Available load current vs. ambient temperature and
airflow rates for Vout = 1.0 V converter mounted horizontally with
Vin = 5 V, and maximum MOSFET temperature 120 C.
0.90
0.85
0.80
0.75
0.90
0.85
0.80
0.75
5.5 V
5.0 V
4.5 V
3.6 V
3.3 V
3.0 V
0.70
0.65
0.70
0.65
0
3
6
9
12
15
18
0
3
6
9
12
15
18
Load Current [Adc]
Load Current [Adc]
Fig. 1.0V.3: Efficiency vs. load current and input voltage for Vout
= 1.0 V converter mounted vertically with air flowing at a rate of
200 LFM (1 m/s) and Ta = 25 C.
Fig. 1.0V.4: Efficiency vs. load current and input voltage for Vout
= 1.0 V converter mounted vertically with air flowing at a rate of
200 LFM (1 m/s) and Ta = 25 C.
MCD10205 Rev. 1.0, 24-Jun-10
Page 21 of 25
www.power-one.com
YS05S16 DC-DC Converter Data Sheet
3.0-5.5 VDC Input; 0.7525-3.63 VDC Programmable @ 16 A
Fig. 1.0V.5: Turn-on transient for Vout = 1.0 V with application of
Fig. 1.0V.6: Output voltage ripple (20 mV/div.) at full rated load
current into a resistive load with external capacitance 100 μF
ceramic + 1 μF ceramic and Vin = 5 V for Vout = 1.0 V. Time
scale: 2 μs/div.
Vin at full rated load current (resistive) and 100 μF external
capacitance at Vin = 5 V. Top trace: Vin (5 V/div.); Bottom trace:
output voltage (1 V/div.); Time scale: 2 ms/div.
Fig. 1.0V.7: Output voltage response Vout = 1.0 V to positive load
current step change from 8 A to 16 A with slew rate of 5 A/μs at
Vin = 5 V. Top trace: output voltage (100 mV/div.); Bottom trace:
load current (5 A/div.). Co = 100 μF ceramic + 1 μF ceramic. Time
scale: 20 μs/div.
Fig. 1.0V.8: Output voltage response for Vout = 1.0 V to negative
load current step change from 16 A to 8 A with slew rate of -5 A/μs
at Vin = 5 V. Top trace: output voltage (100 mV/div.); Bottom
trace: load current (5 A/div.). Co = 100 μF ceramic + 1 μF
ceramic. Time scale: 20 μs/div.
MCD10205 Rev. 1.0, 24-Jun-10
Page 22 of 25
www.power-one.com
YS05S16 DC-DC Converter Data Sheet
3.0-5.5 VDC Input; 0.7525-3.63 VDC Programmable @ 16 A
20
16
20
16
12
8
12
500 LFM (2.5 m/s)
400 LFM (2.0 m/s)
300 LFM (1.5 m/s)
200 LFM (1.0 m/s)
100 LFM (0.5 m/s)
8
500 LFM (2.5 m/s)
400 LFM (2.0 m/s)
300 LFM (1.5 m/s)
200 LFM (1.0 m/s)
100 LFM (0.5 m/s)
30 LFM (0.15 m/s)
4
30 LFM (0.15 m/s)
4
0
0
20
30
40
50
60
70
80
90
20
30
40
50
60
70
80
90
Ambient Temperature [°C]
Ambient Temperature [°C]
Fig. 0.7525V.2: Available load current vs. ambient temperature
and airflow rates for Vout 0.7525 converter mounted
horizontally with Vin = 5 V, and maximum MOSFET temperature
Fig. 0.7525V.1: Available load current vs. ambient temperature
and airflow rates for Vout = 0.7525 V converter mounted vertically
with Vin = 5 V, and maximum MOSFET temperature 120 C.
=
V
120 C.
0.85
0.80
0.75
0.70
0.85
0.80
0.75
0.70
5.5 V
5.0 V
4.5 V
3.6 V
3.3 V
3.0 V
0.65
0.60
0.65
0.60
0
3
6
9
12
15
18
0
3
6
9
12
15
18
Load Current [Adc]
Load Current [Adc]
Fig. 0.7525V.3: Efficiency vs. load current and input voltage for
Vout = 0.7525 V converter mounted vertically with air flowing at a
rate of 200 LFM (1 m/s) and Ta = 25 C.
Fig. 0.7525V.4: Efficiency vs. load current and input voltage for
Vout = 0.7525 V converter mounted vertically with air flowing at a
rate of 200 LFM (1 m/s) and Ta = 25 C.
MCD10205 Rev. 1.0, 24-Jun-10
Page 23 of 25
www.power-one.com
YS05S16 DC-DC Converter Data Sheet
3.0-5.5 VDC Input; 0.7525-3.63 VDC Programmable @ 16 A
Fig. 0.7525V.5: Turn-on transient for Vout = 0.7525 V with
Fig. 0.7525V.6: Output voltage ripple (20 mV/div.) at full rated
load current into a resistive load with external capacitance 100 μF
application of Vin at full rated load current (resistive) and
100 μF external capacitance at Vin = 5 V. Top trace: Vin
(5 V/div.); Bottom trace: output voltage (1 V/div.); Time scale: 2
ms/div.
ceramic
+ 1 μF ceramic and Vin = 5 V for Vout =
0.7525 V. Time scale: 2 μs/div.
Fig. 0.7525V.7: Output voltage response for Vout = 0.7525 V to
positive load current step change from 8 A to 16 A with slew rate
of 5 A/μs at Vin = 5 V. Top trace: output voltage (100 mV/div.);
Bottom trace: load current (5 A/div.). Co = 100 μF ceramic. Time
scale: 20 μs/div.
Fig. 0.7525V.8: Output voltage response for Vout = 0.7525 V to
negative load current step change from 16 A to 8 A with slew rate
of -5 A/μs at Vin = 5 V. Top trace: output voltage (100 mV/div.);
Bottom trace: load current (5 A/div.). Co = 100 μF ceramic. Time
scale: 20 μs/div.
MCD10205 Rev. 1.0, 24-Jun-10
Page 24 of 25
www.power-one.com
YS05S16 DC-DC Converter Data Sheet
3.0-5.5 VDC Input; 0.7525-3.63 VDC Programmable @ 16 A
Physical Information
YS05S Pinout (Surface-Mount)
Pad/Pin Connections
Pad/Pin #
Function
ON/OFF
SENSE
TRIM
1
2
3
4
5
6
Vout
GND
Vin
2
3
4
5
1(*)
6
YS05S Platform Notes
TOP VIEW
(*) PIN # 1 ROTATED 90°
All dimensions are in inches [mm]
Connector Material: Copper
Connector Finish: Gold over Nickel
Converter Weight: 0.22 oz [6.12 g]
Converter Height: 0.327” Max., 0.301” Min.
Recommended Surface-Mount Pads:
Min. 0.080” X 0.112” [2.03 x 2.84]
SIDE VIEW
Converter Part Numbering Scheme
Product
Series
Input
Voltage
Mounting
Scheme
Rated Load
Current
Enable Logic
0
Environmental
YS
05
S
16
–
No Suffix RoHS
lead-solder-exempt
compliant
0 Standard
(Positive Logic)
16 A
S Surface-
Y-Series
3.0 – 5.5 V
(0.7525 V to 3.63 V)
Mount
D Opposite of
Standard
(Negative Logic)
G RoHS
compliant for all six
substances
The example above describes P/N YS05S16-0: 3.0 – 5.5 V input, surface mount, 16 A at 0.7525 V to 3.63 V output, standard
enable logic, and Eutectic Tin/Lead solder. Please consult factory for the complete list of available options.
NUCLEAR AND MEDICAL APPLICATIONS - Power-One products are not designed, intended for use in, or authorized for use as critical
components in life support systems, equipment used in hazardous environments, or nuclear control systems without the express written
consent of the respective divisional president of Power-One, Inc.
TECHNICAL REVISIONS - The appearance of products, including safety agency certifications pictured on labels, may change depending on
the date manufactured. Specifications are subject to change without notice.
MCD10205 Rev. 1.0, 24-Jun-10
Page 25 of 25
www.power-one.com
相关型号:
©2020 ICPDF网 联系我们和版权申明