SRPE-12E1A0 [BEL]
0.6 â 5.5 VDC / 12 A Output;型号: | SRPE-12E1A0 |
厂家: | BEL FUSE INC. |
描述: | 0.6 â 5.5 VDC / 12 A Output |
文件: | 总13页 (文件大小:696K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
The Bel SRPE-12E1A0 is part of the non-isolated DC/DC converter
power module series. The modules use a SMD package. These
converters are available in a range of output voltages from 0.6 VDC to
5.5 VDC over a wide range of input voltage (Vin = 5.5 - 13.2 VDC). The
efficiency is typically 93% at 3.3 Vout (Vin = 12 Vdc) at full load.
5.5 – 13.2 VDC Input
0.6 – 5.5 VDC / 12 A Output
Non-Isolated
Under-Voltage Lockout
High Efficiency
Wide Trim
Fixed Frequency
OCP/SCP
Low Cost
Remote On/Off
Wide Input
Class II, Category 2, Non-Isolated DC/DC Converter
(refer to IPC-9592B)
•
•
•
•
•
•
•
•
•
•
•
•
Networking
Computers and Peripherals
Telecommunications
•
•
•
SRPE-12E1A0
2
OUTPUT
VOLTAGE
MAX. OUTPUT
CURRENT
MAX. OUTPUT
POWER
TYPICAL
EFFICIENCY
MODEL NUMBER
INPUT VOLTAGE
SRPE-12E1A0G
SRPE-12E1A0R
0.6 V - 5.5 V
5.5 V - 13.2 V
12 A
66 W
93%
S
R
PE
-
12
E
1A
0
x
RoHS
Status
Series
Name
Output
Current
Input
Range
Output
Voltage
Active
Logic
Mounting Type
Package
G – Tray Package
R – Tape & Reel Package
5.5 - 13.2 V
0.6 - 5.5 V
Surface Mount
RoHS
SMD SIP
12 A
Active High
PARAMETER
DESCRIPTION
MIN
TYP
MAX
15
UNITS
V
Input Supply Voltage
Remote On/Off
-0.3
-0.3
0
-
-
-
-
-
V
15
C
C
m
Ambient Temperature
Storage Temperature
Altitude
50
-55
-
125
2000
NOTE: All specifications are typical at 25 C unless otherwise stated.
PARAMETER
DESCRIPTION
MIN
TYP
MAX
UNIT
Input Voltage
5.5
-
13.2
V
This power module is not internally fused. An
input line fuse must always be used
Input Current (full load)
-
-
8.5
A
Input Current (no load)
-
-
-
40
1
100
5
mA
mA
mA
Remote Off Input Current
With simulated source impedance of 1000 nH,
5 Hz to 20 MHz. Use a 1000 µF/25 V AL-Cap
with ESR = 0.03 ohm max and 2*100 µF/25 V
Tan cap with ESR = 0.013 ohm max, at
100 kHz @ 25°C.
Input Reflected Ripple Current (rms)
10
20
Input Reflected Ripple Current (pk-pk)
-
35
70
mA
I2t Inrush Current Transient
Turn-on Voltage Threshold
Turn-off Voltage Threshold
-
-
4.2
4
1
A2s
V
4.15
3.7
4.45
4.2
V
NOTE: All specifications are typical at 25 C unless otherwise stated.
tech.support@psbel.com
3
SRPE-12E1A0
PARAMETER
DESCRIPTION
MIN
-2
-3
-2
-70
-2
-15
-
TYP
MAX
2
UNIT
Vo, set ≥ 0.9 VDC
-
-
Output Voltage
Setpoint test condition: Vin = 12 V,
Iout = half load, Ta = 25°C
%Vo,set
Set Point
Vo, set < 0.9 VDC
3
Vo ≥ 3.3 VDC
-
2
%Vo,set
mV
Load
Vin = 12 V, Io = 0 - 12 A, Ta = 25°C
Regulation
Vo < 3.3 VDC
-
70
2
Vo ≥ 3.3 VDC
-
%Vo,set
mV
Line
Vin = 8 - 13.2 V, Io = 6 A, Ta = 25°C
Vin = 5.5 - 13.2 V, Io = 6 A, Ta = 25°C
Regulation
Vo < 3.3 VDC
-
15
-
Regulation Over Temperature
Output Ripple and Noise (pk-pk)
Output Ripple and Noise (rms)
Output Current Range
0.7
-
%Vo,set
mV
-
50
10
12
25
0-20 MHz BW, with 300 µF ceramic capacitor at
output.
-
-
mV
0
-
A
Output DC Current Limit
14
-
A
Output Short-Circuit Current
(Vo ≤ 20 mV) (Hiccup Mode)
-
-
6
Adc
Rise Time
-
-
2
3
0
-
2.9
5
ms
ms
%
Turn On Time
Overshoot at Turn on
Output Capacitance
TRANSIENT RESPONSE
-
4.5
3300
300
µF
-
-
-
-
50
50
50
80
120
150
120
150
mV
µs
Overshoot
△V 50% ~ 100%
Max Load
Settling Time
Overshoot
di/dt = 0.25 A/µs, Vin = 12 VDC, Ta = 25°C, with
300 µF ceramic capacitor at output.
mV
µs
△V 100% ~ 50%
Max Load
Settling Time
NOTE: All specifications are typical at nominal input, full load at 25°C unless otherwise stated.
PARAMETER
DESCRIPTION
MIN
-
TYP
MAX
UNIT
Switching Frequency
650
95.2
93
-
-
-
-
kHz
Vo = 5.5 V
Vo = 3.3 V
Vo = 0.6 V
93.2
91
Efficiency
%
74.5
76.5
This voltage is achieved by trimming up output
slowly.
Calculated Telcordia SR-332, Issue 2 (Vin = 12 V,
Vo = 5.5 V, Io = 12 A, Ta = 40°C, no forced air, 90%
confidence Level, FIT = 109/MTBF)
Output Voltage Trim Range (Wide Trim)
0.6
-
5.5
V
-
FIT
-
-
17.8
-
-
Weight
2.5
g
0.41 x 0.339 x 0.65
inch
mm
Dimensions (L × W × H)
10.41 x 8.60 x 16.51
NOTE: All specifications are typical at nominal input, full load at 25°C unless otherwise stated.
North America
+1 408 785 5200
Asia-Pacific
+86 755 298 85888
Europe, Middle East
+353 61 225 977
© 2021 Bel Power Solutions & Protection
BCD.20133_AL
SRPE-12E1A0
4
Efficiency vs. Output Current at Room Temperature
1
0.8
0.6
0.4
0.2
0
5.5V
12.0V
13.2V
0.6
1.2
2.4
3.6
4.8
6
7.2
8.4
9.6 10.8
12
OUTPUT CURRENT (Amp)
Figure 1. Vout = 0.6 V
Efficiency vs. Output Current at Room Temperature
1.2
1
0.8
0.6
0.4
0.2
0
6V
12.0V
13.2V
0.6
1.2
2.4
3.6
4.8
6
7.2
8.4
9.6
10.8
12
OUTPUT CURRENT (Amp)
Figure 2. Vout = 3.3 V
Efficiency vs. Output Current at Room Temperature
1
0.9
0.8
0.7
0.6
0.5
0.4
8V
12.0V
13.2V
0.6
1.2
2.4
3.6
4.8
6
7.2
8.4
9.6
10.8
12
OUTPUT CURRENT (Amp)
Figure 3. Vout = 5.5 V
tech.support@psbel.com
5
SRPE-12E1A0
PARAMETER
DESCRIPTION
MIN
-0.3
2.4
TYP
MAX
0.8
UNIT
Signal Low (Unit Off)
Active High
-
-
V
V
The remote on/off pin open, Unit off.
Signal High (Unit On)
15
Recommended remote on/off circuit for active high
Vin+
Vin+
On/off
On/off
Vin-
Vin-
Figure 4. Control with open collector/drain circuit
Figure 5. Control with photocoupler circuit
Vin+
Vin+
Vcc
On/off
On/off
Vin-
Vin-
Figure 6. Control with logic circuit
Figure 7. Permanently on
Trim up circuit (using an external resistor)
Figure 8. Trim up circuit
SRPE-12E1A0 Trim up Resistor Calculate:
1.2
Vo − 0.6
Figure 9. Trim up circuit
Rtrim =
k
Vo is the desired output voltage.
Rtrim is the required resistance between TRIM and GND.
North America
Asia-Pacific
Europe, Middle East
+1 408 785 5200
+86 755 298 85888
+353 61 225 977
© 2021 Bel Power Solutions & Protection
BCD.20133_AL
SRPE-12E1A0
6
Vin = 12 V, with maximum junction temperature of semiconductors derated to 115 ˚C.
Figure 10. Forced airflow direction
Figure 11. Vout = 0.6 V
Figure 12. Vout = 1.8 V
Figure 13. Vout = 3.3 V
Figure 14. Vout = 5.5 V
tech.support@psbel.com
7
SRPE-12E1A0
Figure 15. Ripple and noise at full load, 12 V input,
0.6 V output and Ta=25˚C
Figure 16. Ripple and noise at full load, 12 V input,
3.3 V output and Ta = 25˚C
Figure 17. Ripple and noise at full load,
12 V input, 5.5 V output and Ta = 25˚C
NOTE: Test condition of the output ripple and noise: 0-20 MHz BW, with 300 µF ceramic cap at output.
North America
+1 408 785 5200
Asia-Pacific
+86 755 298 85888
Europe, Middle East
+353 61 225 977
© 2021 Bel Power Solutions & Protection
BCD.20133_AL
SRPE-12E1A0
8
Figure 18. 100%-50% Load Transients at Vin = 12 V,
Figure 19. 50%-100% Load Transients at Vin = 12 V,
Vout = 0.6 V @ Ta = 25 ˚C
Vout = 0.6 V @ Ta = 25˚C
Figure 20. 100%-50% Load Transients at Vin = 12 V,
Figure 21. 50%-100% Load Transients at Vin = 12 V,
Vout = 3.3 V @ Ta = 25˚C
Vout = 3.3 V @ Ta = 25˚C
tech.support@psbel.com
9
SRPE-12E1A0
Figure 22. 100%-50% Load Transients at Vin = 12 V,
Figure 23. 50%-100% Load Transients at Vin = 12 V,
Vout = 5.5 V @Ta = 25˚C
Vout = 5.5V @ Ta = 25˚C
NOTE: Test condition of the transient response: di/dt = 0.25 A/µs, with 360 µF ceramic cap at output.
Under-voltage Lockout
Voltage Falling
Voltage Rising
Input Voltage (V)
V1
V2
Figure 24. Input under-voltage lockout
V1 = 4 V
V2 = 4.2 V
North America
Asia-Pacific
Europe, Middle East
+1 408 785 5200
+86 755 298 85888
+353 61 225 977
© 2021 Bel Power Solutions & Protection
BCD.20133_AL
SRPE-12E1A0
10
The SRPE-12E1A0 modules are designed to be compatible with a reflow soldering process. The suggested Pb-free solder paste is
Sn/Ag/Cu(SAC). The recommended reflow profile using Sn/Ag/Cu solder is shown in the following. Recommended reflow peak
temperature is 245˚C while the part can withstand peak temperature of 260˚C maximum for 10 seconds. This profile should be used
only as a guideline. Many other factors influence the success of SMT reflow soldering. Since your production environment may
differ, please thoroughly review these guidelines with your process engineers.
Figure 25. Soldering information
The SRPE-12E1A0 modules have a MSL rating of 3.
The SRPE-12E1A0 modules are designed to be compatible with J-STD-033 Rev: A (Handling, Packing, Shipping and Use of Moisture
/Reflow Sensitive surface Mount devices). Moisture barrier bags (MBB) with desiccant are applied. The recommended storage
environment and handling procedure is detailed in J-STD-033.
This component has been designed, handled, and packaged ready for Pb-free reflow soldering. If the assembly shop follows J-
STD-033 guidelines, no pre-bake of this component is required before being reflowed to a PCB. However, if the J-STD-033
guidelines are not followed by the assembler, Bel recommends that the modules should be pre-baked @ 120~125˚C for a minimum
of 4 hours (preferably 24 hours) before reflow soldering.
tech.support@psbel.com
11
SRPE-12E1A0
Figure 26. Outline
NOTE: 1) All Pins: Material - Copper Alloy;
Finish – 3 micro inches minimum Gold over 50 micro inches minimum Nickel plate.
2) Un-dimensioned components are shown for visual reference only.
3) All dimensions in inch [mm]; Tolerances: x.xx +/-0.02 inch [0.51 mm]; x.xxx +/-0.010 inch [0.25 mm].
North America
Asia-Pacific
Europe, Middle East
+1 408 785 5200
+86 755 298 85888
+353 61 225 977
© 2021 Bel Power Solutions & Protection
BCD.20133_AL
SRPE-12E1A0
12
PIN
1
FUNCTION
Enable
Vin
2
3
GND
4
Vout
5
Trim
Figure 27. Pins
Figure 28. Recommended pad layout
tech.support@psbel.com
13
SRPE-12E1A0
DATE
REVISION
CHANGES DETAIL
APPROVAL
2014-01-25
VP1
First Release
XF.Jiang
1.Ambient Temperature; 2. Add thermal derating curve;3. Output DC
Current Limit; 4. Transient Response; 5.di/dt
1.Mechanical drawing; 2. Output ripple and noise; 3. Output DC Current
Limit; 4. Transient Response; 5.add ROHS logo; 6. Output Voltage Set
Point; 7. Load Regulation; 8. Line Regulation; 9. Output DC Current
Limit; 10. Efficiency; 11. Turn on/off Voltage Threshold; 11. Update
on/off description, add a note for UVLO.
2014-02-10
2014-02-20
A
B
XF.Jiang
XF.Jiang
2014-04-09
2014-06-24
2014-07-03
2014-11-05
2014-11-18
C
D
E
Update MD.
XF.Jiang
XF.Jiang
XF.Jiang
XF.Jiang
XF.Jiang
Update MD.
Update part number explanation, RoHS compliance,Add MD Note.
Update MD.
F
G
Update General Specifications, TD, MD.
Update Input Specs, Output Specs, General, Efficiency Data, NR, TR,
MD.
2015-11-13
H
XF.Jiang
2015-12-22
2016-05-12
2018-02-12
2021-06-29
I
Update Output Specs.
Update Thermal Derating Curves.
Update the form.
XF.Jiang
XF.Jiang
XF.Jiang
XF.Jiang
J
AK
AL
Add object ID.
For more information on these products consult: tech.support@psbel.com
NUCLEAR AND MEDICAL APPLICATIONS - Products are not designed or intended for use as critical components in life support systems,
equipment used in hazardous environments, or nuclear control systems.
TECHNICAL REVISIONS - The appearance of products, including safety agency certifications pictured on labels, may change depending on
the date manufactured. Specifications are subject to change without notice.
North America
Asia-Pacific
Europe, Middle East
+1 408 785 5200
+86 755 298 85888
+353 61 225 977
© 2021 Bel Power Solutions & Protection
BCD.20133_AL
相关型号:
©2020 ICPDF网 联系我们和版权申明