SBLP65-1012G [BEL]
AC-DC Regulated Power Supply Module, 1 Output, 65W, Hybrid, ROHS COMPLIANT PACKAGE-8;型号: | SBLP65-1012G |
厂家: | BEL FUSE INC. |
描述: | AC-DC Regulated Power Supply Module, 1 Output, 65W, Hybrid, ROHS COMPLIANT PACKAGE-8 输入元件 |
文件: | 总6页 (文件大小:85K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
SBLP65 AC-DC Single-Output Series Data Sheet
65 Watts
Features
RoHS compliant for all six substances
Typical 80-85% efficiency
Quasi-resonant ZVS topology with synchronous
rectification
Compact size of 2” x 4” x 1.30”
65 Watts with only 4-5 CFM forced-air cooling
60 Watts with convection cooling
90-264 VAC wide-range input
FCC & CISPR 22, Class "B" – Conducted EMI
Height meets 1U chassis constraints
Two-year limited warranty
Applications
Safety Agency pending to UL60960-1, CSA 22.2 No.
60950-1-03, and TUV EN60950/IEC 60950-1
Telecom, datacom
Networking
Industrial
Consumer
Gaming
Compliance with EN 61000-4-2 level 4 (ESD),
EN 61000-4-3 (RF), EN 61000-4-4 level 3 (Fast
Transient/Burst), EN 61000-4-5 class 3 (Surge)
Description
The SBLP65 is a compact and efficient series of AC-DC power supplies suited for telecom, datacom, and many
other applications. The SBLP65 Series meets the international information technology safety standards with the CE-
Mark for the European Low Voltage Directive (LVD). Its high efficiency allows a very minimal power loss in end
equipment, resulting in higher reliability, ease of thermal management, and regulatory approvals for an
environmentally friendly end product.
Single-Output Model Selection
Model
Nominal
Output Voltage
Min-Max Output
Current (Amps),
Convection
Min-Max Output
Current (Amps),
Forced Air 1
Peak Output
Current
Total
Ripple &
Noise mV
pk-pk % 4
Regulation
(Amps) 2
(%) 3
(VDC)
3.3
5
SBLP65-1003G
SBLP65-1005G
SBLP65-1012G
SBLP65-1015G
SBLP65-1024G
SBLP65-1048G
0 - 11
0 - 11
0 - 5
0 - 11
0 - 11
19
12
1.5
1.0
1.0
1.0
1.0
1.0
2
2
12
0 - 5.4
0 - 4.3
0 - 2.7
0 - 1.35
6.25
5
2
15
0 - 4
2
24
0 - 2.5
0 - 1.25
3.1
1.56
2
48
2
1
4 CFM or 105 LFM (average measurement of six equally-distributed points through a 3.5" x 1.6" (9 cm x 4 cm cross-sectional area) with power
supply mounted on a 0.25" (6.35 mm) standoffs. Recommended airflow direction is from the AC input to the DC output.
2
Peak current duration for less than 30 seconds with a maximum duty cycle of 10%. During peak loading, output may exceed total regulation
limits.
3
At 25 C ambient including voltage set point tolerance, line and load regulation
Maximum peak-to-peak noise at 20 MHz bandwidth measured at the end of a twisted pair cable across a bypass capacitor.
4
MCD10023 Rev. 1.7, 30-Mar-09
Page 1 of 6
www.power-one.com
SBLP65 AC-DC Single-Output Series Data Sheet
65 Watts
ELECTRICAL SPECIFICATIONS
Input Specifications
Parameter
Conditions/Description
Min.
Nom.
Max.
Units
AC Input Voltage
Range
Continuous voltage range
90
100 - 250
264
VAC
DC Input Voltage
Range
For DC input applications, please consult
factory.
VDC
Hz
Frequency
AC Input
47
50 - 60
1.5
63
Power Factor
Complies with EN61000-3-2 Standard for Line
Current Harmonics with input power less than
75 Watts, at <60W output power
Input current
Inrush current
At 90 VAC input and max rating
Amps
rms
115 VAC, Max power, 25 °C
230 VAC, Max power, 25 °C
30
60
A pk
A pk
A
Input fuse
Efficiency
Non-user serviceable internally located AC
input line fuse is provided.
At maximum power, 110 VAC
Single output models above 24V output
Single output 12V model
85
84
80
%
%
%
Single output models below 12V
MCD10023 Rev. 1.7, 30-Mar-09
Page 2 of 6
www.power-one.com
SBLP65 AC-DC Single-Output Series Data Sheet
65 Watts
Output Specifications
Parameter
Conditions/Description
With convection cooling
Min.
Nom.
Max.
Units
1
Output power
60
Watts
1
With 3 CFM forced-air cooling for single output
models
65
Output DC voltages
Output DC current
Minimum load
Vo1 output is adjustable -5/+10 % of nominal
1
1
A
A
Required to meet total regulation
At 264 VAC/60 Hz
Leakage current
Output ripple & noise
0.75
mA
1
mV
pk-pk
Overshoot
Vo1 overshoot at turn-on
5
%
%
Load transient
Vo1 deviation due to a 50 to 100%
load change at a rate of 1A/µs
±5
Turn-On & Turn-Off
characteristics
Outputs turn ON monotonically at minimum
output current or at full load.
Outputs turn OFF monotonically at minimum
output current or at full load.
Turn-on Delay
Turn-on Rise Time
Hold-up Time
Time required for output within regulation after
initial application of AC input @ 90 VAC.
3
Sec
ms
ms
Time required for output voltage to rise from
10% to 90%.
20
Time Vo1 is required to stay within 95%
regulation after removal of AC measure from
the last peak of the AC line at 120 VAC and
max power.
16
Remote Sense
Maximum compensation.
Phase margin.
500
mV
Degrees
dB
Control loop stability
45
10
Gain margin.
1
See Model Selection table.
Fault Protection
Parameter
Conditions/Description
Min.
Nom.
Max.
Units
Current Limit
Protection
Protection is provided.
Short-circuit Protection Provided with auto-recovery.
ADC
VDC
OVP Trip
Vo1, 3.3 V
Vo1, 5 V
3.6
5.6
14
29
55
3.75
6.2
15.35
31.6
57.5
3.95
6.9
16.7
34.2
60
Vo1, 12 V
Vo1, 24 V
Vo1, 48 V
MCD10023 Rev. 1.7, 30-Mar-09
Page 3 of 6
www.power-one.com
SBLP65 AC-DC Single-Output Series Data Sheet
65 Watts
Isolation Requirements
Parameter
Conditions/Description
Min.
Nom.
Max.
Units
Input-to-Chassis
2121
VDC
Input-to-Output
4242
500
VDC
VDC
Output-to-Chassis
EMC Immunity
Parameter
Conditions/Description
ESD
EN 61000-4-2
Level 2.
Level 3.
Level 3.
Class 3.
RF Susceptibility
Fast Transient/Burst
Surge
EN 61000-4-3
EN 61000-4-4
EN 61000-4-5
RF Immunity
EN 61000-4-6. Class 3.
EN 61000-4-8.
Magnetic Fields
Voltage Interruptions
EN 61000-4-11.
EMC Emmisions
Parameter
Conditions/Description
FCC Part 15
Conducted Class B, Radiated Class A.
Conducted Class B, Radiated Class A.
CISPR 22
Environmental Specifications
Parameter
Conditions/Description
Min.
Nom.
Max.
Units
Cooling
Rated for convection and forced-air cooling.
Audible Noise
Operating Temp
0
dBA
ºC
-10 ºC to 50 ºC with linear derating to 50% at
70 ºC. Unit will start up at -10 ºC, but will not
meet all published specifications.
-10
50
70
Altitude
Operating.
Non-Operating.
10K
50K
ASL ft
ASL ft
Storage Temp
Humidity
-40
85
2.4
6
ºC
95% relative humidity @ 40 ºC, non-condensing
Vibration
Operating: Random vibration; 5 to 500 Hz
(10 minutes, each axis).
Grms
Grms
Non-Operating: Random vibration; 5 to 500 Hz
(10 minutes, each axis).
Shock
Operating: half-sine, 11 ±3 ms, 3-axis.
15
40
G
G
Non-Operating: half-sine, 11 ±3 ms, 3-axis.
MCD10023 Rev. 1.7, 30-Mar-09
Page 4 of 6
www.power-one.com
SBLP65 AC-DC Single-Output Series Data Sheet
65 Watts
Regulatory & Safety Approvals
Parameter
Conditions/Description
Min.
Nom.
Max.
Units
UL60950-1
3.3V and 5V single-output models are pending.
3.3V and 5V single-output models are pending.
CSA-C22.2,
No. 60950-1-03
EN 60950-1
3.3V and 5V single-output models are pending.
/IEC 60950-1
CE Mark for LVD
CB Approval
3.3V and 5V single-output models are pending.
3.3V and 5V single-output models are pending.
At 12 VAC.
Ground Continuity
40
A
Mechanical Specifications
Parameter
Conditions/Description
Min.
Nom.
Max.
101.6
50.8
Units
mm
Dimensions
Length
Width
mm
Height, including component or component lead
protrusion on the bottom of the PCB.
33.02
mm
Power Density
Mounting
Input
With forced-air cooling.
4.81
W/cu in
(Location/Hardware); see Outline Drawing.
(Location/Connector);
J1 - Molex 41791 series or equivalent
Output
(Location/Connector);
J2 - Molex 41791 series or equivalent
Remote Sense
Combined into J2, pins 5 & 6 for single-output
models.
Outline Drawing
Pins/Functions
See Mechanical Drawing.
Weight
0.115
kg
Connector kit
Mounting distance
Consult factory
Distance from the bottom of the components or
component leads (solder side) or top of the
components (component side) to the
customer's metal chassis
2.87
mm
Reliability
Parameter
Conditions/Description
Min.
Nom.
Max.
Units
Calculated MTBF
250,000
Hours
Demonstrated MTBF
550,000
Hours
MCD10023 Rev. 1.7, 30-Mar-09
Page 5 of 6
www.power-one.com
SBLP65 AC-DC Single-Output Series Data Sheet
65 Watts
Mechanical Drawing
SBLP65 Single-Output Drawing:
J1 - AC CONN.
Pin 1
AC Line
Pin 3
AC Neutral
4.00 +/- 04
J2 - DC CONN.
Ø 0.16 (4 places)
Pin #1
3.75
Pin 1
Pin 2
Pin 3
Pin 4
Pin 5
Pin 6
Vout
Vout
J1 input
connector
COMMON
COMMON
-Sense
TOP VIEW
J2 - DC output
connector
(see pin-out
table)
+Sense
Pin #1
2.00
+/-.04
1.75
safety ground
connection point
PCB AC Ground Connection
Point - Solder side
fastener
clearance area
0.25 DIA (4
places)
0.06
1.10
1.30
+/-.04
END VIEW
SIDE VIEW
0.
1
Printed Circuit Board
0.14
NUCLEAR AND MEDICAL APPLICATIONS - Power-One products are not designed, intended for use in, or authorized for use as critical
components in life support systems, equipment used in hazardous environments, or nuclear control systems without the express written consent
of the respective divisional president of Power-One, Inc.
TECHNICAL REVISIONS - The appearance of products, including safety agency certifications pictured on labels, may change depending on the
date manufactured. Specifications are subject to change without notice.
MCD10023 Rev. 1.7, 30-Mar-09
Page 6 of 6
www.power-one.com
相关型号:
SBLP65-1015G
AC-DC Regulated Power Supply Module, 1 Output, 65W, Hybrid, ROHS COMPLIANT PACKAGE-8
BEL
SBLP65-1024G
AC-DC Regulated Power Supply Module, 1 Output, 65W, Hybrid, ROHS COMPLIANT PACKAGE-8
BEL
SBLP65-1048G
AC-DC Regulated Power Supply Module, 1 Output, 65W, Hybrid, ROHS COMPLIANT PACKAGE-8
BEL
SBLP65-3300G
AC-DC Regulated Power Supply Module, 3 Output, 65W, Hybrid, ROHS COMPLIANT PACKAGE-8
BEL
©2020 ICPDF网 联系我们和版权申明