GMDC12V08PSRT001 [BEL]
DORADO MV DC/DC CONVERTERS; DORADO压DC / DC转换器
| 型号： | GMDC12V08PSRT001 |
| 厂家： | 
BEL FUSE INC. |
| 描述： | DORADO MV DC/DC CONVERTERS |
| 文件： | 总7页 (文件大小：536K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
DORADO MV DC/DC CONVERTERS
24V Input – 12VDC – 8A Output
POWER PRODUCTS
GMDC12V08
1
GMDC12V08 – /4 Brick Dorado MV Series
•
•
•
•
•
•
•
•
•
Industry standard pinout and footprint
High efficiency: 86% at 12V, 8A; 88% at 12V, 4A
Very low common-mode noise for a commercial DC/DC converter
Constant switching frequency
Remote sense
Single board design
Optional low profile heat sink for improved thermal performance
Header with M3 metal inserts for mechanical connection to PCB
Optional low profile
Control Functions
•
Uses innovative control and power
topology for lower parts count
Microprocessor controlled
Primary-side enable, choice of logic
Industry standard output trim
Typical Characteristics
•
•
•
•
•
•
•
•
Output setpoint accuracy: 1.5%
Load regulation: 0.25%
Line regulation: 0.25%
Regulation over line, load and temperature: 3%
Low output ripple
Protection Features
•
•
•
•
Over temperature protection
Over voltage protection
Over current protection
Over/Under input voltage protection
Ordering Information
Standard Model Number Input Voltage Output Voltage Max Current
Example Part Number:
(All optionsꢀ
GMDC12V08*
24V
12V
8A
GMDC12V08 PSR 00X
* Options:
E = 0.18" Pins ( .01"ꢀ
M = 0.145" Pins ( .01"ꢀ
S = 0.12" Pins ( .01"ꢀ
R = Heat Sink-Ready
P = Positive Logic Version;
High = On
Part Number
Dorado MV Heat Sink
Part Numbers
Options:
Positive Logic Version
Optional Pin Lengths
E = 0.18"
Typical Thermal Performance
Part
Natural Convection
Power Dissipation†
Forced Convection
Thermal Resistance‡
Height
Number
M = 0.145"
S = 0.12"
001
002
003
004
0.25"
0.50"
1.00"
0.13"
5W
7W
5.8 C/W
Heat Sink-Ready
Heat Sink
˚
3.2 C/W
˚
001 = 0.25"
002 = 0.50"
003 = 1.00"
004 = 0.13"
11W
TBD
2.0 C/W
˚
TBD
† @ 60 C rise heat sink to ambient
‡ @ 300'/min.
˚
©2006 Bel Fuse Inc. Specifications subject to change without notice. 11.06
Bel Power Inc. 155 Flanders Road, Westborough, MA 01581 • Tel 508-870-9775 • Fax 508-870-9796 • www.belpower.com
page 1
DORADO MV DC/DC CONVERTERS
24V Input – 12VDC – 8A Output
POWER PRODUCTS
GMDC12V08
Input Specifications
Parameter
Min
Typical
Max
36
4
Units
Operating Input Voltage
Input Current
18
24
V
DC
A
Input Capacitance
Input Hysteresis, Low Line
6
1
µF
V
DC
V
= 24V , T @25˚ C, 300 LFM Airflow, V
= 12V , I
= 8A unless otherwise noted.
IN
DC
A
OUT
DC OUT
Available output power depends on ambient temperature and good thermal management.
(See application graphs for limits.ꢀ
Output Specifications
Parameter
Min
Typical
Max
103
20
Units
Regulation Over Line, Load & Temperature
Voltage Ripple
97
%V
NOM
RMS
P–P
mV
mV
Voltage Ripple, 20MHz BW
Current Range
60
0
8
A
Current Limit Inception
105
120
%I
OUT
Output Transient Response, 50% to 75% Load Change, 1A/µsec
Settling Time to 1%
5
%V
OUT
400
300
0
µS
mS
Turn-on Time to 98% Vnom
Output Overshoot at Turn-on
Trim Range
%V
OUT
OUT
OUT
60
110
%V
%V
Over Voltage Protection, Latching
125
©2006 Bel Fuse Inc. Specifications subject to change without notice. 11.06
Bel Power Inc. 155 Flanders Road, Westborough, MA 01581 • Tel 508-870-9775 • Fax 508-870-9796 • www.belpower.com
page 2
DORADO MV DC/DC CONVERTERS
24V Input – 12VDC – 8A Output
POWER PRODUCTS
GMDC12V08
Isolation Specifications
Parameter
Min
2000
10
Typical
Max
Units
Isolation Test Voltage, Input/Baseplate/Output (Basicꢀ
Isolation Resistance
V
DC
MΩ
Features
Parameter
Min
Typical
Max
Units
1
Over Temperature Protection, Thermal Sensor
117
C
˚
Switching Frequency, Fixed
300
kHz
1. PCB less than 130 C.
˚
Approvals and Standards
General Specifications
Operating Temperature
UL and c-UL Recognized Component, TUV,
UL60950, CSA 22.2 No. 950, IEC/EN 60950**
-40 C to + 100 C
˚
˚
Storge Temperature
Relative Humidity
Vibration
-55 C + 125 C
˚
˚
EMC Characteristics:
10% to 95% RH, Non-condensing
2 to 9 Hz, 3mm disp., 9 to 200 Hz, 1g
UL V-0
Designed to meet emission and immunity
requirements per EN55022, CISPR 22,
Class B, and CISPR 24.
Material Flammability
Weight
** An external fuse shall be used to comply with
the requirements.
30 grams
MTBF Telcordia (Bellcoreꢀ
2.0 million hours
©2006 Bel Fuse Inc. Specifications subject to change without notice. 11.06
Bel Power Inc. 155 Flanders Road, Westborough, MA 01581 • Tel 508-870-9775 • Fax 508-870-9796 • www.belpower.com
page 3
DORADO MV DC/DC CONVERTERS
24V Input – 12VDC – 8A Output
POWER PRODUCTS
GMDC12V08
Application Notes
™
CoolConverter
Bel Power’s Proprietary CoolConverter™
•
•
An advanced microcontroller reduces parts count while
adding features, performance and flexibility in the design.
Patented single-stage power conversion architecture,
control and magnetic design allow unprecedented
power density and efficiency in an isolated power
supply.
•
Low common-mode noise results from lower capacitance
in the transformer from balanced winding design.
Protection and Control
Valid Input Voltage Range
The converter measures the input voltage and will not allow
operation outside of the input voltage specification. As
shown by the graphs, hysteresis is added to both the high
and low voltage to prevent the converter from turning on and
off repeatedly when the voltage is held near either voltage
extreme. At low line, this assures the maximum input current
is not exceeded; at high line, this assures the semiconductor
devices in the converter are not damaged by excessive
voltage stress.
Over Voltage Hysteresis
1.0
ON/OFF Logic Option
The ON/OFF control logic can be either Negative (standardꢀ
or Positive to enable the converter. For Negative logic, the
ON/OFF pin is brought to below 1.0V with respect to the
–INPUT pin to enable the converter. The pull-down must be
able to sink 100µA. For Positive logic, the ON/OFF pin is
brought to greater than 4.0V with respect to the –INPUT pin
and be limited to less than 10V. To request the Positive logic
version, add the suffix (Pꢀ to the standard part number. The
ON/OFF pin has a built-in pull-up resistor of approximately
100kΩ to +5V.
0
76.5 77 77.5 78 78.5 79 79.5 80 80.5
Input Voltage (V)
Under Voltage Hysteresis
1.0
Output Over Voltage Protection
The output voltage is constantly monitored by the
microprocessor with a redundant secondary-side
measurement circuit that both shuts down the duty cycle and
triggers the microprocessor to shut down. If the output voltage
exceeds the over voltage specification, the microprocessor
will latch the converter off. To turn the converter on required
either cycling the ON/OFF pin or power to the converter. This
advanced feature prevents the converter from damaging the
load if there is a converter failure or application error. If non-
latching is required, consult factory.
0
30
31
32
33
34
35
36
37
Input Voltage (V)
©2006 Bel Fuse Inc. Specifications subject to change without notice. 11.06
Bel Power Inc. 155 Flanders Road, Westborough, MA 01581 • Tel 508-870-9775 • Fax 508-870-9796 • www.belpower.com
page 4
DORADO MV DC/DC CONVERTERS
24V Input – 12VDC – 8A Output
POWER PRODUCTS
GMDC12V08
CoolConverter™
Protection and Control
Trim-up
Thermal Shutdown
The printed circuit board temperature is measured using a
semiconductor sensor. If the maximum rated temperature
is exceeded, the converter is latched off. To re-enable the
converter requires cycling the ON/OFF pin or power to the
converter. If non-latching is required, consult factory.
12ꢀ(100+∆%ꢀ
1.25∆%
(100+2∆%ꢀ
∆%
_
RTRIM-UP
=
5.11kΩ
ꢀ
{
}
ꢀ
12.0V Trim-up
10000
1000
100
Remote Sense
The output voltage is regulated at the point where the
sense pins connect to the power output pins. Total sense
compensation should not exceed 0.4V or 10% of Vout,
whichever is greater.
Safety
An external input fuse must always be used to meet these
safety requirements.
0
2
3
4
5
6
7
8
9
10
1
External Output Trimming
+Sense
Increase in Output Voltage (%)
Trim
Up
10K
Trimpot
Trim
Trim
Down
Trim-down
–Sense
100ꢀ
_
RTRIM-DOWN
=
2
5.11kΩ
ꢀ
ꢀ
∆%
{ }
Trim
To trim the output voltage higher, connect the required trim
resistor from the Trim pin to the +Sense pin. To trim the output
voltage lower, connect the required trim resistor from the Trim
pin to the –Sense pin. See the diagrams at right.
Trim-down
1000
100
10
0
2
3
4
5
6
7
8
9
10
1
Decrease in Output Voltage (%)
©2006 Bel Fuse Inc. Specifications subject to change without notice. 11.06
Bel Power Inc. 155 Flanders Road, Westborough, MA 01581 • Tel 508-870-9775 • Fax 508-870-9796 • www.belpower.com
page 5
DORADO MV DC/DC CONVERTERS
24V Input – 12VDC – 8A Output
POWER PRODUCTS
GMDC12V08
Efficiency Data
Power Dissipation
Start Up
Voltage Ripple
1. V
12mV/div 20µS/div
OUT
1. V
12V/div 80ms/div
OUT
2. I
8A/div
OUT
Transient Response
Line/Load Regulation
12.100
12.060
12.020
11.980
11.940
11.900
18V Vin
24V Vin
36V Vin
0
4
8
Output Current (A)
1. V
200mV/div 1µs/div
OUT
2. Enable 100mV/div
©2006 Bel Fuse Inc. Specifications subject to change without notice. 11.06
Bel Power Inc. 155 Flanders Road, Westborough, MA 01581 • Tel 508-870-9775 • Fax 508-870-9796 • www.belpower.com
page 6
DORADO MV DC/DC CONVERTERS
24V Input – 12VDC – 8A Output
POWER PRODUCTS
GMDC12V08
Mechanical
GMDC12V08
Pin Configuration – Bottom View
Pin
1
Function
+ Input
On/Off
Pin Dia. (In.)
0.040
Notes:
1. Mechanical tolerances
x.xxx in. = 0.005 in.
x.xx in = 0.01 in.
2
0.040
3
– Input
0.040
2. Pin material: Brass with tin/lead plating over nickel
3. Workmanship: Meets or exceeds IPC-A-610B Class II
4. "A" = 0.040" dia. pins
4
– Output
– Sense
Trim
0.060
5
0.040
5. "B" = 0.060" dia. pins
6. Min. screw length for heat sink attachment
= 4.5mm + heat sink flange + locking hardware
6
0.040
7
+ Sense
+ Output
0.040
8
0.060
RoHS Compliance
Complies with the European Directive 2002/95/EC, calling for the elimination of lead and other
hazardous substances from electronic products. These parts are not however compatible with
the higher temperatures associated with lead free solder processes and must be soldered using
a reflow profile with a peak temperature of no more than 240 C.
˚
©2006 Bel Fuse Inc. Specifications subject to change without notice. 11.06
CORPORATE
FAR EAST
EUROPE
Bel Fuse Inc.
Bel Fuse Ltd.
8F / 8 Luk Hop Street
San Po Kong
Kowloon, Hong Kong
Tel 852-2328-5515
Fax 852-2352-3706
www.belfuse.com
Bel Fuse Europe Ltd.
206 Van Vorst Street
Jersey City, NJ 07302
Tel 201-432-0463
Fax 201-432-9542
www.belfuse.com
Preston Technology Management Centre
Marsh Lane, Suite G7, Preston
Lancashire, PR1 8UD, U.K.
Tel 44-1772-556601
Fax 44-1772-888366
www.belfuse.com
page 7
相关型号：
©2020 ICPDF网 联系我们和版权申明