0RQB-X0S11L [BEL]
45-58 VDC Input;
| 型号： | 0RQB-X0S11L |
| 厂家： | 
BEL FUSE INC. |
| 描述： | 45-58 VDC Input |
| 文件： | 总19页 (文件大小：1585K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
0RQB-X0S11x is an isolated and regulated DC-DC converter that
operates from a nominal 52 VDC source. This unit provides up to
1000 W of output power from a nominal 52 VDC input.
This unit is designed to be highly efficiency and low cost. Features
include remote on/off, short circuit protection, over current protection,
under voltage lockout, power good indication and over temperature
protection.
The converter is provided in an industry standard quarter brick
package.
45-58 VDC Input
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
11.1 VDC @ 0 A Output / 10.6 VDC @ 94.3 A Output
Isolated 1/4th Brick Converter
Fixed Frequency (300 kHz)
High Efficiency
High Power Density
Input Under Voltage Lockout
OCP/SCP
Output Over-voltage Protection
Over Temperature Protection
Remote On/Off
Power Good Indication
Parallel Operation with Droop
Approved to UL/CSA/IEC60950-1, 2nd +A2 version (TBD)
Class II, Category 2, Isolated DC/DC Converter (refer to IPC-9592B)
Networking
Computers and Peripherals
Telecommunications
•
•
•
2
0RQB-X0S11x
MODEL
NUMBER
MODEL
NUMBER
OUTPUT
VOLTAGE
INPUT
VOLTAGE
MAX. OUTPUT
CURRENT
MAX. OUTPUT
POWER
TYPICAL
EFFICIENCY
0RQB-X0S11L
0RQB-X0S11B
0RQB-X0S11D
0RQB-X0S110
0RQB-X0S11A
0RQB-X0S11C
10.6 VDC
10.6 VDC
10.6 VDC
45 VDC - 58 VDC
45 VDC - 58 VDC
45 VDC - 58 VDC
94.3 A
94.3 A
94.3 A
1000 W
1000 W
1000 W
97.3%
97.3%
97.3%
NOTE: Add “G” suffix at the end of the model number to indicate Tray Packaging.
0
R
QB
-
X0
S
11
x
y
RoHS
Status
Series
Name
Output
Power
Input
Range
Output
Voltage
Package
Type
Mounting Type
Active Logic
0 – active high, Openframe
L – active low, Openframe
Through hole
mount
RoHS
6
1/4th
Brick
A – active high, with HSK plate
B – active low , with HSK plate
C – active high, with HSK with Fins
D – active low, with HSK with Fins
G – Tray
package
1000 W
45 – 58V
10.6 V
PARAMETER
DESCRIPTION
MIN
-0.3
-0.3
1500
-40
-40
-
TYP
MAX
80
UNITS
Continuous non-operating Input Voltage
Remote On/Off
-
-
-
-
-
-
-
V
V
18
I/O Isolation Voltage
Ambient Temperature
Storage Temperature
Altitude
-
V
85
C
C
m
%
125
4000
90
Relative Humidity
Operating, Non-Condensing
10
NOTE: Ratings used beyond the maximum ratings may cause a reliability degradation of the converter or may permanently damage the device.
All specifications are typical at 25°C unless otherwise stated.
PARAMETER
DESCRIPTION
MIN
TYP
52
MAX
58
UNIT
V
Operating Input Voltage
Input Current (full load)
Input Current (no load)
45
-
-
28
A
-
100
150
mA
Remote Off Input Current
-
10
50
20
-
mA
mA
mA
mA
A2s
V
Input Reflected Ripple Current (rms)
Input Reflected Ripple Current (pk-pk)
Input Terminal Ripple Current Ic (RMS)
I2t Inrush Current Transient
-
Detail conditions please refer to input reflected
ripple current section.
-
200
-
-
-
1000
TBD
45.0
42.0
-
-
42.0
39.0
-
-
UVLO Turn on Voltage Threshold
UVLO Turn off Voltage Threshold
OVLO Turn off Voltage Threshold
OVLO Turn on Voltage Threshold
43.5
40.5
63
Input undervoltage lock-out(UVLO)
Input overvoltage lock-out(OVLO)
V
V
-
60
-
V
CAUTION: This converter is not internally fused. An input line fuse must be used in application. Recommend a fast-acting fuse with
maximum rating of 30 A on system board. Refer to the fuse manufacture’s datasheet for further information.
tech.support@psbel.com
3
0RQB-X0S11x
All specifications are typical at nominal input, full load at 25°C unless otherwise stated.
PARAMETER
DESCRIPTION
MIN
11.045
10.52
TYP
11.1
10.6
MAX
11.155
10.68
UNIT
Vin = 52 V, Io = 0 load
Vin = 52 V, Io = 100% load
V
V
Output Voltage Set Point
Over all operating input voltage, resistive
load and temperature conditions until end of
life
Output Voltage Range
10.3
-
11.4
V
Load Regulation
Vin = 52 V, Io = 0~100% load
-
-
-
-
-
0.50
0.40
50
0.60
0.50
100
150
20
V
Line Regulation
Vin = 45-58 V, Io = 100% load
Ambient temperature = -40°C to 85°C
V
Regulation Over Temperature
Ripple and Noise (pk-pk)
Ripple and Noise (rms)
mV
mV
mV
1000 uF, 50% ceramic, 50% Oscon or
POSCAP. Measured at output pins,
bandwidth = 20MHz.
50
10
Output Ripple and Noise (pk-pk)
under worst case
Over all operating input voltage, load and
ambient temperature condition
-
-
-
150
mV
Vin = 45 V
Vin = 52 V
Vin = 58 V
0
0
96.2
94.3
92.9
116
15
A
A
Output Current Range
0
A
Output DC Current Limit
Rise time
100
-
108
6
A
ms
Defined as time between Vin reaching
Turn-On voltage and Vout reaching 90% of
final value
Defined as time between Enable and Vout
reaching 10% of final value
-
-
23
-
30
5
ms
ms
Turn on Time
Turn-On Overshoot
Turn-Off Undershoot
Overshoot at turn On
Undershoot at turn Off
-
-
-
-
350
350
mV
mV
Typically 50% ceramic, 50% Oscon or
POSCAP.
Output Capacitance
Pre-Bias Voltage
0
0
-
-
6250
Vout
uF
V
5 V step in 1 us occurring within Vin
Operating Range. Pout = 10%-100% Rated
Power, Cout = Cout Max/2
Response to Vin Step
-
-
1.25
V
Transient Response
△V 50%~75% of Max Load
Settling Time
-
-
-
-
-
350
-
mV
us
Loadstep = 25% of Rated Power at 1 A/uS,
4 uF/W of external capacitance,
measured at output pins.
200
-
△V 75%~50% of Max Load
Settling Time
350
-
mV
us
200
North America
Asia-Pacific
Europe, Middle East
+1 408 785 5200
+86 755 298 85888
+353 61 225 977
© 2017 Bel Power Solutions & Protection
Rev. AD1
4
0RQB-X0S11x
Line regulation +/-0.2V
Load regulation 0.5V
11.5
11.0
10.5
10.0
9.5
Min Load
Max Laod
9.0
52
39 40 41 42 43 44 45 46
57 58
Vin_min
Vin_typ
Vin_max
Input Voltage(V)
PARAMETER
DESCRIPTION
MIN
TYP
97.3
300
130
-
MAX
UNIT
Efficiency
Vin = 52 V, full load
-
-
-
-
-
-
-
-
-
-
%
kHz
℃
Switching Frequency
-
Over Temperature Protection
Output Over Voltage Protection
-
13.2
V
0RQB-X0S110/L
0RQB-X0S11A/B
0RQB-X0S11C/D
TBD
TBD
TBD
TBD
-
-
-
-
-
g
Weight
g
g
Calculated Per Bell Core SR-332 (Vin = 52 V,
FIT
-
Vo=10.6V, Io=80% load Ta=40°C, 200LFM,
FIT=109/MTBF)
MTBF
TBD
Mhrs
2.30 x 1.45 x 0.48
58.42 x 36.83 x 12.20
2.30 x 1.45 x 0.57
58.42 x 36.83 x 14.48
2.30 x 1.45 x 1.16
58.42 x 36.83 x 29.37
in
mm
in
mm
in
0RQB-X0S110/L
0RQB-X0S11A/B
0RQB-X0S11C/D
Dimensions (L × W × H)
mm
Isolation Characteristics
Input to Output
1500
1500
500
10M
-
-
-
-
-
-
-
V
V
Input to Case
-
Output to Case
-
-
V
Isolation Resistance
Isolation Capacitance
Ohm
pF
2700
tech.support@psbel.com
5
0RQB-X0S11x
99.00%
98.00%
97.00%
96.00%
95.00%
94.00%
93.00%
92.00%
91.00%
90.00%
89.00%
45V
52V
58V
50 100 175 250 375 500 625 750 875 1000
OUTPUT POWER(W)
PARAMETER
DESCRIPTION
MIN
-0.3
2.4
-0.3
2.4
-
TYP
MAX
0.8
18
UNIT
V
Signal Low (Unit On)
-
-
-
-
-
-
-
-
-
Active
Low
Remote On/Off pin is open,
the module is off.
Signal High (Unit Off)
V
Signal Low (Unit Off)
0.8
18
V
Active
High
Remote On/Off pin is open,
the module is on
Signal High (Unit On)
V
EnablePin Open-Circuit Voltage
EnablePin Current(into pin, ext. pull-up to 15 V)
EnablePin Current(into pin, ext. pull-up to 10 V)
EnablePin Current (out of pin, Unit On)
EnablePin Current (out of pin, Unit Off)
18
V
-
0.5
0.3
200
-
mA
mA
uA
uA
-
-
10
North America
Asia-Pacific
Europe, Middle East
+1 408 785 5200
+86 755 298 85888
+353 61 225 977
© 2017 Bel Power Solutions & Protection
Rev. AD1
6
0RQB-X0S11x
Recommended remote on/off circuit for active low
Vin+
On/off
Vin-
Vin+
On/off
Vin-
Control with open collector/drain circuit
Control with photocoupler circuit
Vin+
Vin+
Vcc
On/off
Vin-
On/off
Vin-
Permanently on
Control with logic circuit
Recommended remote on/off circuit for active high
Vin+
Vin+
On/off
Vin-
On/off
Vin-
Control with open collector/drain circuit
Control with photocoupler circuit
Vin+
Vin+
Vcc
On/off
On/off
Vin-
Vin-
Control with logic circuit
Permanently on
tech.support@psbel.com
7
0RQB-X0S11x
1. The Power Good signal is a non-latching open-collector output that is Low during normal operation and is pulled High when
any of the following conditions occur:
•
•
•
•
Over-Temperature
Over-Current
Vout is outside of the DC Output Band while Vin is within the Vin Operating Range
Vin is within the Vin Operating Range but the unit is not operating (to determine if 1 Unit used in a parallel configuration
is not operating)
•
Vin is outside of the Vin Operating Range
2. The Power Good signal is referenced to Vout(-).
PARAMETER
DESCRIPTION
MIN
8.6
12.8
42.5
59
-
TYP
MAX
9.0
13.2
45
UNIT
Output Voltage High (trigger limits)
Output Voltage High (trigger limits)
Input Voltage Low (trigger limits) Rising
Input Voltage High (trigger limits) Rising
Hysteresis
-
-
-
-
1
-
-
-
-
V
V
PG signal indicates good when Vin is within
operating range and indicates bad ~20ms before
unit is shut-down due to OV
V
62
V
-
V
High State Voltage
0
5.5
10
V
High State Leakage Current (into Pin)
Low State Voltage
0
µA
V
0
0.8
5
Low State Current (into Pin)
0
mA
Power Good Signal
De-assert Response Time
Power Good Signal
Duration between the fault occurring and the
Power-Good Signal de-asserting
Duration between unit powering up with no faults
and the Power Good Signal asserting
Duration the Power-Good signal stays de-asserted
if a transient fault occurs
0
0
-
-
3
3
ms
ms
ms
oC
Assert Response Time
Power Good Signal Duration
200
600
For OT Warning, the PG signal will toggle as an
impulse wave.
Over Temperature Warning
120
OT Warning PG signal frequency
OT Warning PG signal duty cycle
70
-
110
kHZ
%
47.5
50
52.5
Testing setup:
is
ic
Ls
Vin+
+
+
Cs
Cin
Vin-
Notes and values in testing.
Ls: Simulated Source Impedance (10uH).
Cs: Offset possible source Impedance (100μF, ESR<0.2Ω@ 100kHz, 20C ).
Cin: Electrolytic capacitor, should be as closed as possible to the power module to swallow ic ripple current and
help with stability. Recommendation: 100μF, ESR<0.2Ω@ 100kHz, 20C.
North America
Asia-Pacific
Europe, Middle East
+1 408 785 5200
+86 755 298 85888
+353 61 225 977
© 2017 Bel Power Solutions & Protection
Rev. AD1
8
0RQB-X0S11x
Below measured waveforms are based on above simulated and recommended inductance and capacitance.
is (input reflected ripple current), AC component
ic (input terminal ripple current), AC component
Test condition: 52Vdc input, 10.6Vdc/94.3A output and Ta=25 deg C, with a 1µF ceramic capacitor and a 270uF AL. cap at output.
Note: Ripple and noise at full load, 52Vdc input, 10.6Vdc/94.3A output and Ta=25°C,and with a 1uF ceramic cap and a 1000uF cap
(50% ceramic, 50% Oscon or POSCAP) at output. Ripple and noise at full load, 52Vdc input, 10.6Vdc/94.3A output and Ta=25°C,and
with a 1uF ceramic cap and a 1000uF cap (50% ceramic, 50% Oscon or POSCAP) at output.
tech.support@psbel.com
9
0RQB-X0S11x
To provide protection in a fault output overload condition, the module is equipped with internal current-limiting circuitry and can
endure current limiting for a few mili-seconds. If the overcurrent condition persists beyond a few milliseconds, the module will shut
down into hiccup mode and restart once every 250ms. The module operates normally when the output current goes into specified
range. The typical average output current is 1.6A during hiccup.
CH1: Output Voltage
CH1: Output Voltage
CH2: Output current waveform
CH2: Output current waveform
Expansion of on time portion of above figure
Test condition:Vin=52V@Ta=25℃
Under-voltage Lockout
V1=40.5V
V2=43.5V
Voltage Falling
Voltage Rising
Input Voltage (V)
V1
V2
North America
+1 408 785 5200
Asia-Pacific
+86 755 298 85888
Europe, Middle East
+353 61 225 977
© 2017 Bel Power Solutions & Protection
Rev. AD1
10
0RQB-X0S11x
Rise time
Vout=10.6V/94.3A @Vin=52V, Ta=25℃ Cext=0uF
Vout=10.6V/94.3A @Vin=52V, Ta=25℃, Cext =6250uF
Startup time
Startup from Vin;
Ch1: Vo;
Startup from on/off;
Ch1: Vo;
Ch3: on/off
Ch3: Vin
Vout=10.6V/94.3A @Vin=52V, Ta=25℃ Cext=0uF
Vout=10.6V/94.3A @Vin=52V, Ta=25℃ Cext=0uF
tech.support@psbel.com
11
0RQB-X0S11x
Shutdown
Vout=10.6V/94.3A @Vin=52V, Ta=25℃ Cext=0uF
Vout=10.6V/94.3A @Vin=52V, Ta=25℃, Cext =6250uF
75%-50% Load Transients at Vin=52V@Ta=25℃
50%-75% Load Transients at Vin=52V@Ta=25℃
Note: Transient Response at Vin=52V , di/dt=1A/μS, 1μF ceramic cap and 3300μF AL. cap at output, Ta=25C.
North America
Asia-Pacific
Europe, Middle East
+1 408 785 5200
+86 755 298 85888
+353 61 225 977
© 2017 Bel Power Solutions & Protection
Rev. AD1
12
0RQB-X0S11x
Thermal Considerations
New high power architectures require an accurate thermal design. Design engineers have to optimize the module working conditions
and ensure reliable operation. Convection cooling is the common mode to cool down the module.
Heat transfer is dependent on a test setup and it is important to characterize the module in an environment similar to existent
electronic applications.
Reported thermal data reflects real operating conditions because the values are physically measured in a wind tunnel.
Thermal Test Setup
A module in electronic cards is typically located in a busy area without relevant space around it. To simulate a real condition and
avoid turbulence we add a cover with defined dimensions.
The distance has to be 6.35mm (0.25”inch) from the top of the module and 6.35mm (0.25”inch) on the left and right side of the
module.
The values reflect most of the real applications and it is a common procedure in the power module market.
Ambient temperature and airflow are measured in front of the module at the distance of 76.2 mm (3 inch).
For 0RQB-X0S11 A/B
tech.support@psbel.com
13
0RQB-X0S11x
The OTP is achieved by temperature sensor U10 and it's in non-latch mode when OTP occurs. The protecting point will be varied a
little under different conditions (air flow, ambient temperature, input voltage, load...). To enhance system reliability, the power
module should always be operated below the maximum operating temperature shown as blow figures.
Temperature reference points on top side
Temperature reference point for 0RQB-X0S110/L
Temperature reference point for 0RQB-X0S11A/B
Temperature reference point for 0RQB-X0S11C/D
North America
Asia-Pacific
Europe, Middle East
+1 408 785 5200
+86 755 298 85888
+353 61 225 977
© 2017 Bel Power Solutions & Protection
Rev. AD1
14
0RQB-X0S11x
Derating Curves for 0RQB-X0S110/L
Derating Curves for 0RQB-X0S110/L
Vin=52V, Longitudinal Orientation, airflow from Vout to Vin.
Vin=52V, Transverse Orientation, airflow from Vout+ to Vout-.
Derating Curves for 0RQB-X0S11A/B
Derating Curves for 0RQB-X0S11A/B
Vin=52V, Longitudinal Orientation, airflow from Vout to Vin.
Vin=52V, Transverse Orientation, airflow from Vout+ to Vout-.
Derating Curves for 0RQB-X0S11C/D
Derating Curves for 0RQB-X0S11C/D
Vin=52V, Longitudinal Orientation, airflow from Vout to Vin.
Vin=52V, Transverse Orientation, airflow from Vout+ to Vout-.
tech.support@psbel.com
15
0RQB-X0S11x
PIN SIZE
0.04”
LENGTH
0.180”
0.180”
0.180”
0.180”
0.180”
0.180”
0.180”
0.180”
PIN
1
FUNCTION
Vin (+)
0.04”
2
Enable
Vin (-)
0.04”
3
0.062”
0.062”
0.04”
4
Vout(-)
5
Vout(-)
6
PGOOD
Vout(+)
Vout(+)
0.062”
0.062”
7
8
NOTES: This module is recommended and compatible with Pb-Free Wave Soldering and must be soldered using a peak solder
temperature of no more than 260 ºC for less than 5 seconds.
1) All Pins: Material - Copper Alloy;
Finish – Tin plated
2) Undimensioned components are shown for visual reference only.
3) All dimensions in inches; Tolerances: x.xx +/-0.02 in [0.51 mm].
x.xxx +/-0.010 in [0.25 mm].
North America
Asia-Pacific
Europe, Middle East
+1 408 785 5200
+86 755 298 85888
+353 61 225 977
© 2017 Bel Power Solutions & Protection
Rev. AD1
16
0RQB-X0S11x
PIN SIZE
0.04”
LENGTH
0.180”
0.180”
0.180”
0.180”
0.180”
0.180”
0.180”
0.180”
PIN
1
FUNCTION
Vin (+)
0.04”
2
Enable
Vin (-)
0.04”
3
0.062”
0.062”
0.04”
4
Vout(-)
5
Vout(-)
6
PGOOD
Vout(+)
Vout(+)
0.062”
0.062”
7
8
NOTES: This module is recommended and compatible with Pb-Free Wave Soldering and must be soldered using a peak solder
temperature of no more than 260 ºC for less than 5 seconds.
1) All Pins: Material - Copper Alloy;
Finish – Tin plated
2) Undimensioned components are shown for visual reference only.
3) All dimensions in inches; Tolerances: x.xx +/-0.02 in [0.51 mm].
x.xxx +/-0.010 in [0.25 mm].
tech.support@psbel.com
17
0RQB-X0S11x
17.3
PIN SIZE
0.04”
LENGTH
0.180”
0.180”
0.180”
0.180”
0.180”
0.180”
0.180”
0.180”
PIN
1
FUNCTION
Vin (+)
0.04”
2
Enable
Vin (-)
0.04”
3
0.062”
0.062”
0.04”
4
Vout(-)
5
Vout(-)
6
PGOOD
Vout(+)
Vout(+)
0.062”
0.062”
7
8
NOTES: This module is recommended and compatible with Pb-Free Wave Soldering and must be soldered using a peak solder
temperature of no more than 260 ºC for less than 5 seconds.
1) All Pins: Material - Copper Alloy;
Finish – Tin plated
2) Undimensioned components are shown for visual reference only.
3) All dimensions in inches; Tolerances: x.xx +/-0.02 in [0.51 mm].
x.xxx +/-0.010 in [0.25 mm].
North America
Asia-Pacific
Europe, Middle East
+1 408 785 5200
+86 755 298 85888
+353 61 225 977
© 2017 Bel Power Solutions & Protection
Rev. AD1
18
0RQB-X0S11x
Safety :
EMC:
Material flammability: UL94V-0
Compliance to EN/IEC60950-1
Compliance to UL/CSA60950-1
1. Surge:
IEC61000-4-5
2. DC-DIP:
3. Conductive EMI:
IEC61000-4-29
EN55022 class A
Compliance to EN55022 class A (both peak and average) with the following inductive and capacitive filter
Setup:
ITEM
DESIGNATOR
CX2
PARAMENTER
VENDOR
VENDOR P/N
1
2
\
\
\
\
\
\
\
\
\
\
\
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
CX3
3
CY31
4
CY32
5
CY41
6
CY42
7
RY31
8
RY32
9
RY41
10
11
RY42
T2A
T1A,CX1,CX2,RY11,RY21,
RY12,RY22,CY11,CY21,CY122,CY22
12
NIL
-
-
tech.support@psbel.com
19
0RQB-X0S11x
DATE
REVISION
CHANGES DETAIL
APPROVAL
Zhao Tang
Zhao Tang
Zhao Tang
Zhao Tang
2016-2-19
2016-05-17
2016-06-20
2016-08-10
A
B
C
D
First release
Add PGOOD Item; Change Remote turn-on time and Mechanical Outline.
Update Start up Figures
Update UVLO, TD Curve and Mechanical Outline
NUCLEAR AND MEDICAL APPLICATIONS - Products are not designed or intended for use as critical components in life support systems,
equipment used in hazardous environments, or nuclear control systems.
TECHNICAL REVISIONS - The appearance of products, including safety agency certifications pictured on labels, may change depending on the
date manufactured. Specifications are subject to change without notice.
North America
Asia-Pacific
Europe, Middle East
+1 408 785 5200
+86 755 298 85888
+353 61 225 977
© 2017 Bel Power Solutions & Protection
Rev. AD1
相关型号：
0RSB-30T025
DC-DC Regulated Power Supply Module, 1 Output, 25W, Hybrid, ROHS COMPLIANT PACKAGE-8
BEL
0RSB-30T033G
DC-DC Regulated Power Supply Module, 1 Output, 30W, Hybrid, ROHS COMPLIANT PACKAGE-8
BEL
0RSB-30T03LG
DC-DC Regulated Power Supply Module, 1 Output, 30W, Hybrid, ROHS COMPLIANT PACKAGE-8
BEL
0RSB-30T050
DC-DC Regulated Power Supply Module, 1 Output, 35W, Hybrid, ROHS COMPLIANT PACKAGE-8
BEL
0RSB-30T05L
DC-DC Regulated Power Supply Module, 1 Output, 35W, Hybrid, ROHS COMPLIANT PACKAGE-8
BEL
0RSB-30T120
DC-DC Regulated Power Supply Module, 1 Output, 36W, Hybrid, ROHS COMPLIANT PACKAGE-8
BEL
0RSB-30T12L
DC-DC Regulated Power Supply Module, 1 Output, 36W, Hybrid, ROHS COMPLIANT PACKAGE-8
BEL
0RSB-30TV20
DC-DC Regulated Power Supply Module, 1 Output, 18W, Hybrid, ROHS COMPLIANT PACKAGE-8
BEL
0RSB-30TV50
DC-DC Regulated Power Supply Module, 1 Output, 19.5W, Hybrid, ROHS COMPLIANT PACKAGE-8
BEL
©2020 ICPDF网 联系我们和版权申明