0RQB-D0T280G [BEL]

DC-DC Regulated Power Supply Module;
0RQB-D0T280G
型号: 0RQB-D0T280G
厂家: BEL FUSE INC.    BEL FUSE INC.
描述:

DC-DC Regulated Power Supply Module

文件: 总8页 (文件大小:160K)
中文:  中文翻译
下载:  下载PDF数据表文档文件
ISOLATED DC/DC CONVERTERS  
48 Vdc Input 28 Vdc /7 A Output  
0RQB-D0T28x  
RoHS Compliant  
Rev.B  
Fixed Frequency (300 kHz)  
Isolated  
Output Over Voltage Latch Off  
Over Temperature Protection  
Short Circuit Latch Off  
Low Cost  
High Efficiency  
High Power Density  
Input Under Voltage Lockout  
Basic Insulation  
Remote On/Off  
Droop Load Share with 0.125V/A  
Wide Output Trim Range  
Voltage Fold-back Constant  
Current Limit  
Description  
The 0RQB-D0T28x is isolated dc/dc converter that operates from a nominal 48 Vdc source. This unit will provide  
up to 196 W of output power from a nominal 48 Vdc input. The unit is designed to be highly efficient and low cost.  
Features include remote on/off, output current limit protection, input under-voltage lockout and output over-  
voltage latch off. This converter is provided in an industry standard quarter brick package.  
Part Selection  
Output  
Input Voltage  
Max. Output  
Current  
Max. Output  
Power  
Typical  
Efficiency  
Model Number  
Active High  
Model Number  
Active Low  
Voltage  
28 Vdc  
36 Vdc - 75 Vdc  
7 A  
196 W  
92%  
0RQB-D0T280  
0RQB-D0T28L  
Notes: 1. Add “G” suffix at the end of the model number to indicate Tray Packaging.  
2. All part numbers above indicate RoHS 6. Change the second letter "R" to "7" for RoHS 5 part numbers.  
Absolute Maximum Ratings  
Parameter  
Min  
Typ  
Max  
Notes  
Continuous Input Voltage  
-0.3 V  
-
80 V  
Transient Input Voltage  
Remote On/Off  
-
-
-
-
-
-
100 V  
18 V  
100 mS Max  
-0.3 V  
-
I/O Isolation Voltage  
Ambient Temperature  
Storage Temperature  
1500 V  
85 °C  
125 °C  
-40 °C  
-55 °C  
Note: All specifications are typical at 25 °C unless otherwise stated.  
Input Specifications  
Parameter  
Min  
Typ  
Max  
Notes  
Input Voltage  
36 V  
48 V  
75 V  
Input Current (no load)  
Input Current (full load)  
Remote Off Input Current  
-
-
-
40 mA  
-
60 mA  
7 A  
14 mA  
20 mA  
Input Reflected Ripple Current  
(pk-pk)  
With simulated source impedance of 12  
uH, 5 Hz to 20 MHz; use a 220uF/100 V  
electrolytic capacitor with ESR = 1 ohm  
max. at 200 kHz  
-
-
20 mA  
5 mA  
30 mA  
10 mA  
Input Reflected Ripple Current  
(rms)  
Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302 Tel 201-432-0463 Fax 201-432-9542 www.belfuse.com  
ISOLATED DC/DC CONVERTERS  
48 Vdc Input 28 Vdc /7 A Output  
Input Specifications (continued)  
Parameter  
Min  
Typ  
Max  
Notes  
I2t Inrush Current Transient  
-
-
0.1 A2s  
Turn-on Voltage Threshold  
Turn-off Voltage Threshold  
33 V  
31 V  
34 V  
33 V  
35 V  
34 V  
Notes: 1. Should place at least 100uF/100V electrolytic capacitor directly adjacent to the input pin of the module.  
2. All specifications are typical at nominal input, full load at 25 °C unless otherwise stated.  
Output Specifications  
Parameter  
Min  
Typ  
Max  
Notes  
Output Voltage Set Point  
27.44 V  
28.0 V  
28.56 V  
Vin=48 V, Io=No Load  
Droop Rate  
-
-
125 mV/A  
28 mV  
-
Line Regulation  
56 mV  
Regulation Over Temperature  
(-40 °C to 85 °C)  
-
0.02%Vo/℃  
-
Output Current  
0 A  
-
7 A  
Current Limit Threshold  
7.5 A  
8.2 A  
9.5 A  
Ripple and Noise (rms)  
Ripple and Noise (pk-pk)  
-
-
20 mV  
50 mV  
0 - 20 MHz BW, with 1 uF  
ceramic load capacitor and a  
100uF Al capacitor at the output  
100 mV  
180 mV  
Turn on Time  
-
-
65 mS  
100 mS  
5%  
Overshoot at Turn on  
Output Capacitance  
Transient Response  
0%  
-
68 uF  
4700 uF  
Overshoot  
Settling Time  
Overshoot  
-
-
-
-
375 mV  
600 mV  
50% ~ 75%  
Max Load  
di/dt=0.1A/us, Vin=48Vdc,  
Ta=25 °C, with 1 uF  
ceramic capacitor and a  
100uF Al capacitor at the  
output.  
800 uS  
375 mV  
800 uS  
1000 uS  
600 mV  
1000 uS  
VO=28 V  
75% ~ 50%  
Max Load  
Settling Time  
Note: All specifications are typical at nominal input, full load at 25 °C unless otherwise stated.  
General Specifications  
Parameter  
Min  
Typ  
Max  
Notes  
Vin=48 V, full load  
Efficiency  
89%  
92%  
-
Switching Frequency  
Isolation characteristics  
Input to Output  
270 kHz  
300 kHz  
330 kHz  
-
-
1500 V  
Input to Case  
-
-
1500 V  
Output to Case  
-
-
500 V  
Isolation Resistance  
Isolation Capacitance  
10M Ohm  
-
-
-
-
1000 pF  
Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302 Tel 201-432-0463 Fax 201-432-9542 www.belfuse.com  
ISOLATED DC/DC CONVERTERS  
48 Vdc Input 28 Vdc /7 A Output  
General Specifications (continued)  
Parameter  
Min  
Typ  
Max  
Notes  
Remote Sense Compensation  
0 V  
-
1.5 V  
The voltage increased by trim and  
sense should not exceed 110%Vout.  
Output Voltage Trim Range  
Over Temperature Protection  
Over Voltage Protection  
60%  
-
-
110%  
130 ℃  
34 V  
125 ℃  
32 V  
-
Vin=48 V, Io=full load, Latch mode  
Calculated Per Bell Core SR-332  
(Vin=48 V, Vo=28 V, Io=5.6 A, 400LFM  
forced air flow,Ta = 25 °C)  
MTBF  
TBD  
Dimensions  
Inches (L × W × H)  
Millimeters (L × W × H)  
2.28 x 1.45 x 0.50  
57.91 x 36.83 x 12.7  
Weight  
-
60 g  
-
Note: All specifications are typical at 25 °C unless otherwise stated.  
Control Specifications  
Parameter  
Min  
Typ  
Max  
Notes  
Remote On/Off  
Signal Low (Unit On)  
Signal High (Unit Off)  
Signal Low (Unit Off)  
Signal High (Unit On)  
-0.3 V  
2.4 V  
-0.3 V  
2.4 V  
-
-
-
-
0.8 V  
18 V  
0.8 V  
18 V  
The Remote On/Off pin is open,  
Unit off.  
Active Low  
Active High  
The Remote On/Off pin is open,  
Unit on  
Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302 Tel 201-432-0463 Fax 201-432-9542 www.belfuse.com  
ISOLATED DC/DC CONVERTERS  
48 Vdc Input 28 Vdc /7 A Output  
Output Trim Equations  
Equations for calculating the trim resistor are shown below. The Trim Down resistor should be connected  
between the Trim pin and Sense(-) pin. The Trim Up resistor should be connected between the Trim pin and the  
Sense(+) pin. Only one of the resistors should be used for any given application.  
Sense(+)  
Trim  
100  
Rtrimdown = 6.19×  
1 3.01  
[
kΩ  
]
delta  
Module  
Rtrimdown  
Rtrimup  
Sense(-)  
Vo×  
(
100 + delta  
)
100  
Rtrimup = 6.19×  
[
9.2 kΩ  
]
Vref × Delta  
delta  
Sense(+)  
Trim  
Note:  
Module  
(
Vo _ req Vo  
)
delta =  
×100  
%
[ ]  
Sense(-)  
Vo  
Output voltage Vo=28 V  
10000  
Rdown(delta)  
1
0
delta  
50  
100000  
Rup(delta)  
100  
0
delta  
10  
Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302 Tel 201-432-0463 Fax 201-432-9542 www.belfuse.com  
ISOLATED DC/DC CONVERTERS  
48 Vdc Input 28 Vdc /7 A Output  
Efficiency Data  
90.0%  
85.0%  
80.0%  
75.0%  
70.0%  
36 V  
48 V  
75 V  
0.7  
1.75  
3.5  
5.25  
7
OUTPUT CURRENT(A)  
Thermal Derating Curve  
Vin=48V, with maximum junction temperature of semiconductors derated to 120.  
Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302 Tel 201-432-0463 Fax 201-432-9542 www.belfuse.com  
ISOLATED DC/DC CONVERTERS  
48 Vdc Input 28 Vdc /7 A Output  
Ripple and Noise Waveform  
Note: Ripple and noise at full load, 48 Vdc input, 28 Vdc/7 A output, and with a 1 uF ceramic cap and a 100 uF  
aluminum cap at the output, Ta=25 deg C.  
Transient Response Waveforms  
25%-50% Load Transients at Vin=48  
50%-25% Load Transients at Vin=48 V  
Note: Transients response at di/dt=0.1 A/us, Vin=48 Vdc, Ta=25 °C, with 1 uF ceramic capacitor and a 100 uF  
aluminum cap at the output.  
Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302 Tel 201-432-0463 Fax 201-432-9542 www.belfuse.com  
ISOLATED DC/DC CONVERTERS  
48 Vdc Input 28 Vdc /7 A Output  
Droop Rate  
Typical Output Voltage vs. Load Current at Ta=25C.  
Current Limit  
Output Current Limit Characteristics vs. Output Voltage at Ta=25C.  
Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302 Tel 201-432-0463 Fax 201-432-9542 www.belfuse.com  
ISOLATED DC/DC CONVERTERS  
48 Vdc Input 28 Vdc /7 A Output  
Mechanical Outline  
Pin Connections  
Pin  
Function  
Pin Size  
0.040’’  
0.040’’  
0.040’’  
0.062’’  
0.040’’  
0.040’’  
0.040’’  
0.062’’  
1
Vin(+)  
2
On/Off  
Vin(-)  
3
4
Vo(-)  
5
Sense(-)  
Trim  
6
7
Sense(+)  
Vo(+)  
8
RoHS Compliance  
Complies with the European Directive 2002/95/EC, calling for the elimination of lead and  
other hazardous substances from electronic products.  
©2008 Bel Fuse Inc. Specifications subject to change without notice. 103008  
CORPORATE  
FAR EAST  
EUROPE  
Bel Fuse Inc.  
Bel Fuse Ltd.  
Bel Fuse Europe Ltd.  
206 Van Vorst Street  
Jersey City, NJ 07302  
Tel 201-432-0463  
Fax 201-432-9542  
www.belfuse.com  
8F/ 8 Luk Hop Street  
San Po Kong  
Kowloon, Hong Kong  
Tel 852-2328-5515  
Fax 852-2352-3706  
www.belfuse.com  
Preston Technology Management Centre  
Marsh Lane, Suite G7, Preston  
Lancashire, PR1 8UD, U.K.  
Tel 44-1772-556601  
Fax 44-1772-888366  
www.belfuse.com  

相关型号:

0RQB-D0T28L

DC-DC Regulated Power Supply Module
BEL

0RQB-D0W12LG

DC-DC Regulated Power Supply Module,
BEL

0RQB-D0W15LG

Power Supply Module,
BEL

0RQB-Q0T12C

ISOLATED DC/DC CONVERTERS
BEL

0RQB-Q0T12D

ISOLATED DC/DC CONVERTERS
BEL

0RQB-Q0T12DG

DC-DC Regulated Power Supply Module, 1 Output, 400W, Hybrid, QUARTER BRICK PACKAGE-5
BEL

0RQB-Q0T12F

DC-DC Regulated Power Supply Module, 1 Output, 400W, Hybrid, QUARTER BRICK PACKAGE-5
BEL

0RQB-Q0T12FG

DC-DC Regulated Power Supply Module, 1 Output, 400W, Hybrid, QUARTER BRICK PACKAGE-5
BEL

0RQB-Q2T065

ISOLATED DC/DC CONVERTERS
BEL

0RQB-Q2T06L

ISOLATED DC/DC CONVERTERS
BEL

0RQB-Q2T06LG

DC-DC Regulated Power Supply Module, 1 Output, 390W, Hybrid, ROHS COMPLIANT, QUARTER BRICK PACKAGE-5
BEL

0RQB-Q2T06X

ISOLATED DC/DC CONVERTERS
BEL