0RQ1-T0T12B [BEL]
ISOLATED DC/DC CONVERTERS; 隔离式DC / DC转换器型号: | 0RQ1-T0T12B |
厂家: | BEL FUSE INC. |
描述: | ISOLATED DC/DC CONVERTERS |
文件: | 总11页 (文件大小:405K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
ISOLATED DC/DC CONVERTERS
36 Vdc - 75 Vdc Input,
12 Vdc/25 A Output
Jun. 14, 2011
Bel Power Inc., a subsidiary of Bel Fuse Inc.
0RQ1-T0T12x
Features
RoHS Compliant
Rev.D
Output Over Voltage Shutdown
Output Voltage Trim
Isolated
High Efficiency
Fixed Frequency (270 kHz)
High Power Density
Over Temperature Protection
SCP/OCP
Input Under Voltage Lockout
Input Over Voltage Lockout
Positive/Negative Remote Sense
Low Cost
Basic Insulation
Remote On/Off
Trim and Remote Sense Function (Optional)
Class 1, Category 2, Isolated DC/DC Converter (refer to IPC-9592)
UL60950-1 Recognized (UL/cUL) (Pending)
Applications
Networking
Computers and peripherals
Telecommunications
Description
The 0RQ1-T0T12x are isolated dc/dc converters that operate from a nominal 48 Vdc source. These units will
provide up to 300 W output power from a nominal 48 Vdc input. These units are designed to be highly efficient
and low cost. Features include remote on/off, over current protection and under-voltage lockout. These
converters are provided in an industry standard quarter brick package.
Part Selection
Output Voltage
Input Voltage
Max. Output Max. Output
Typical
Efficiency
Model Number
Active Low
Model Number
Active High
Current
Power
12 Vdc
12 Vdc
36 Vdc - 75 Vdc
36 Vdc - 75 Vdc
25 A
300 W
95%
95%
0RQ1-T0T12L
0RQ1-T0T12B
0RQ1-T0T120
0RQ1-T0T12A
25 A
300 W
Note: Add “G” suffix at the end of the model number to indicate Tray Packaging.
Part Number Explanation
0 R Q1 – T0 T 12 x
1 2
3
4 5 6 7
1---Through hole mount
2---RoHS 6, change “R” to “7” means RoHS 5
3---Series name, 1/4 brick
4---Series code
5---Input range (36-75V)
6---Output voltage (12V)
7---Suffix, “0”&“L”indicated the unit with trim and remote sense function, and “A”&“B” without trim and
remote sense function.
Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302 Tel 201-432-0463 Fax 201-432-9542 www.belfuse.com
1
ISOLATED DC/DC CONVERTERS
36 Vdc - 75 Vdc Input,
12 Vdc/25 A Output
Jun. 14, 2011
Bel Power Inc., a subsidiary of Bel Fuse Inc.
Absolute Maximum Ratings
Unit
Parameter
Min
Typ
Max
Notes
Continuous non-operating Input
Voltage
-0.3
-
80
V
Remote On/Off
-0.3
-
-
-
-
-
18
2250
85
V
V
I/O Isolation Voltage
Ambient Temperature
Storage Temperature
-40
-55
C
C
125
Note: Ratings used beyond the maximum ratings may cause a reliability degradation of the converter or may
permanently damage the device.
Input Specifications
Parameter
Min
Typ
Max
Unit
Notes
Operating Input Voltage
36
48
75
V
Input Current (full load)
Input Current (no load)
Remote Off Input Current
-
-
-
-
10
-
A
90
10
mA
mA
-
Input Reflected Ripple Current
(rms)
With simulated source impedance of
10 uH, 5 Hz to 20 MHz; use a 100
uF/100 V electrolytic capacitor with
ESR = 1 ohm max, at 200 kHz@25°C.
-
-
15
50
-
-
mA
Input Reflected Ripple Current
(pk-pk)
mA
I2t Inrush Current Transient
Turn-on Voltage Threshold
Turn-off Voltage Threshold
-
-
TBD
34.5
34
-
35.5
-
A2s
V
32.5
V
CAUTION: This converter is not internally fused. An input line fuse must be used in application.
Recommend a fast-acting fuse with maximum rating of 14A on system board. Refer to the fuse
manufacture’s datasheet for further information.
Note: All specifications are typical at 25 C unless otherwise stated.
Output Specifications
Parameter
Min
Typ
Max
Unit
Notes
Output Voltage Set Point
11.76
12
12.24
V
Vin=48 V, Io=50%Load
Load Regulation
Line Regulation
-
-
±30
±12
±60
±24
mV
mV
Regulation Over Temperature
(-40deg.C-85deg.C)
-
±60
±100
mV
0 - 20 MHz BW, with 1 uF ceramic
load capacitor and a 10 uF
tantalum capacitor at the output.
Ripple and Noise (pk-pk)
Ripple and Noise (rms)
Output Current Range
Output DC Current Limit
-
-
50
20
-
100
50
mV
mV
A
0
25
26
32
38
A
Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302 Tel 201-432-0463 Fax 201-432-9542 www.belfuse.com
2
ISOLATED DC/DC CONVERTERS
36 Vdc - 75 Vdc Input,
12 Vdc/25 A Output
Jun. 14, 2011
Bel Power Inc., a subsidiary of Bel Fuse Inc.
Output Specifications (continued)
Parameter
Min
Typ
Max
Unit
Notes
Short Circuit Surge Transient
-
TBD
-
A2s
Turn on Time
-
-
80
0
120
3
mS
%
Overshoot at Turn on
Output Capacitance
0
-
5600
uF
Transient Response
△V
50%~75%
of Max Load
Overshoot
Settling Time
Overshoot
-
-
-
-
-
600
300
600
300
mV
uS
di/dt=0.1A/us, Vin=48Vdc, Ta=25
°C, with 1 uF ceramic capacitor and
a 10 uF tantalum capacitor at the
output.
-
-
-
Vo=
12 V
△V
75%~50%
of Max Load
mV
uS
Settling Time
Note: All specifications are typical at nominal input, full load at 25°C unless otherwise stated.
General Specifications
Parameter
Min
Typ
Max
Unit
Notes
Vin=48 V, full load.
Efficiency
94
95
-
%
Switching Frequency
-
-
-
-
270
2200
125
14
-
-
-
-
kHz
pF
℃
Isolation Capacitance
Over Temperature Protection
Over Voltage Protection
V
The total voltage increased by trim
and remote sense should not exceed
5%Vo.
Output Voltage Trim Range
80
-
105
%Vo,set
Remote Sense Compensation
Weight
-
-
-
5
-
%Vo,set
g
71
Calculated Per Bell Core SR-332
(Vin=48 V, Vo=12 V, Io=20 A, Ta =
25 C, FIT=109/MTBF)
FIT
TBD
-
-
Dimensions
Inches (L × W × H)
Millimeters (L × W × H)
2.28 x 1.45 x 0.50
57.91 x 36.83 x 12.70
Note: All specifications are typical at 25 C unless otherwise stated.
Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302 Tel 201-432-0463 Fax 201-432-9542 www.belfuse.com
3
ISOLATED DC/DC CONVERTERS
36 Vdc - 75 Vdc Input,
12 Vdc/25 A Output
Jun. 14, 2011
Bel Power Inc., a subsidiary of Bel Fuse Inc.
Efficiency Data
98.00%
96.00%
94.00%
92.00%
90.00%
88.00%
86.00%
84.00%
82.00%
80.00%
36 V
48 V
75 V
2.50
6.25
12.50
18.75
25.00
OUTPUT CURRENT(A)
Thermal Derating Curve
Maximum junction temperature of semiconductors derated to 120 degree C.
Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302 Tel 201-432-0463 Fax 201-432-9542 www.belfuse.com
4
ISOLATED DC/DC CONVERTERS
36 Vdc - 75 Vdc Input,
12 Vdc/25 A Output
Jun. 14, 2011
Bel Power Inc., a subsidiary of Bel Fuse Inc.
Ripple and Noise Waveform
48 Vdc input, 12 Vdc/25 A output
Note: Ripple and noise at full load, with a 1uF ceramic cap and a 10 uF Tantalum cap at output, Ta=25 deg C.
Transient Response Waveforms
50%-75% Load Transients at Vin=48 V
75%-50% Load Transients at Vin=48 V
Note: Transient response at di/dt=0.1A/us, with a 1uF ceramic cap and a 10uF Tantalum cap at output, and
Ta=25 deg C.
Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302 Tel 201-432-0463 Fax 201-432-9542 www.belfuse.com
5
ISOLATED DC/DC CONVERTERS
36 Vdc - 75 Vdc Input,
12 Vdc/25 A Output
Jun. 14, 2011
Bel Power Inc., a subsidiary of Bel Fuse Inc.
Remote On/Off
Parameter
Min
Typ
Max
Unit
Notes
Signal Low (Unit On)
Signal High (Unit Off)
Signal Low (Unit Off)
Signal High (Unit On)
Current Sink
-0.3
-
0.8
V
Active Low
Active High
The remote on/off pin open, Unit off.
2.4
-0.3
2.4
0
-
-
-
-
18
0.8
18
V
V
The remote on/off pin open, Unit on.
V
0.75
mA
Recommended remote on/off circuit for active low
Vin+
On/off
Vin-
Vin+
On/off
Vin-
Control with open collector/drain circuit
Control with photocoupler circuit
Vin+
Vin+
Vcc
On/off
Vin-
On/off
Vin-
Control with logic circuit
Permanently on
Recommended remote on/off circuit for active high
Vin+
Vin+
On/off
Vin-
On/off
Vin-
Control with open collector/drain circuit
Control with photocoupler circuit
Vin+
Vin+
Vcc
On/off
Vin-
On/off
Vin-
Control with logic circuit
Permanently on
Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302 Tel 201-432-0463 Fax 201-432-9542 www.belfuse.com
6
ISOLATED DC/DC CONVERTERS
36 Vdc - 75 Vdc Input,
12 Vdc/25 A Output
Jun. 14, 2011
Bel Power Inc., a subsidiary of Bel Fuse Inc.
Output Trim Equations
Equations for calculating the trim resistor are shown below. The Trim Down resistor should be connected
between the Trim pin and GND pin. The Trim Up resistor should be connected between the Trim pin and the
Vout pin. Only one of the resistors should be used for any given application.
Minimum trim down voltage is 9.6V
Maximum trim up voltage is 12.6V.
The total voltage increased by trim and remote sense should not exceed 5% of the nominal output voltage.
Vout
511
Rtrimdown
10.22 k
delta
Module
Module
Trim
GND
Rtrimdown
Rtrimup
(100 delta)Vo5.11 626
1.225delta
Vout
Trim
GND
Rtrimup
10.22 k
Note:
Vo _ req Vo
delta
100
%
Vo
Vo_req=Desired (trimmed) output voltage [V]
Output voltage Vo=12 V
Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302 Tel 201-432-0463 Fax 201-432-9542 www.belfuse.com
7
ISOLATED DC/DC CONVERTERS
36 Vdc - 75 Vdc Input,
12 Vdc/25 A Output
Jun. 14, 2011
Bel Power Inc., a subsidiary of Bel Fuse Inc.
Remote Sense
This module has remote sense compensation feature. It can minimize the effects of resistance between
module’s output and load in system layout and facilitates accurate voltage regulation at load terminals or
other selected point.
1. The remote sense lines carries very little current and hence do not require a large cross-sectional area.
2. This module compensates for a maximum drop of 5% of the nominal output voltage.
3. If the unit is already trimmed up, the available remote sense compensation range should be
correspondingly reduced. The total voltage increased by trim and remote sense should not exceed 5%
of the nominal output voltage.
4. When using remote sense compensation, all the resistance, parasitic inductance and capacitance of the
system are incorporated within the feedback loop of this module. It can make an effect on the module's
compensation, affecting the stability and dynamic response. A 0.1uF ceramic capacitor can be
connected at the point of load to de-couple noise on the sense wires.
5. Recommend the connection of remote sense compensation as below figure. There are a resistor RS+
(100 ohm) from Vo+ to Sense+ and a resistor RS- (51 ohm)) from Vo- to Sense- inside of this module.
Vo+
Sense+
Load
Sense-
Vo-
6. If not using remote sense compensation, please connect sense directly to output at module's pin, that is,
connect sense+ to Vo+ and sense- to Vo- at module's pin, the shorter the better. See below figure.
Vo+
Sense+
Load
Sense-
Vo-
Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302 Tel 201-432-0463 Fax 201-432-9542 www.belfuse.com
8
ISOLATED DC/DC CONVERTERS
36 Vdc - 75 Vdc Input,
12 Vdc/25 A Output
Jun. 14, 2011
Bel Power Inc., a subsidiary of Bel Fuse Inc.
Mechanical Outline
0RQ1-T0T120 & 0RQ1-T0T12L
Pin Connections
pin# function pin size
1
2
3
4
5
6
7
8
Vin (+)
On/Off
Vin (-)
Vo (-)
RS (-)
Trim
0.04"
0.04"
0.04"
0.06"
0.04"
0.04"
0.04"
0.06"
RS (+)
Vo (+)
Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302 Tel 201-432-0463 Fax 201-432-9542 www.belfuse.com
9
ISOLATED DC/DC CONVERTERS
36 Vdc - 75 Vdc Input,
12 Vdc/25 A Output
Jun. 14, 2011
Bel Power Inc., a subsidiary of Bel Fuse Inc.
Mechanical Outline
0RQ1-T0T12A & 0RQ1-T0T12B
Pin Connections
pin# function pin size
1
2
3
4
5
Vin (+)
On/Off
Vin (-)
Vo (-)
0.04"
0.04"
0.04"
0.06"
0.06"
Vo (+)
Note: This module is recommended and compatible with Pb-Free Wave Soldering and must be soldered
using a peak solder temperature of no more than 260 ºC for less than 5 seconds.
Note:
1) All Pins: Material - Copper Alloy;
Finish – 3 micro inches minimum Gold over 50 micro inches minimum Nickel plate.
2) Undimensioned components are shown for visual reference only.
3) All dimensions in inches (mm); Tolerances: x.xx +/-0.02 in. (x.x +/-0.5mm) x.xxx +/-0.010 in. (x.xx +/-0.25mm).
Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302 Tel 201-432-0463 Fax 201-432-9542 www.belfuse.com
10
ISOLATED DC/DC CONVERTERS
36 Vdc - 75 Vdc Input, 12 Vdc/25 A Output
Jun. 14, 2011
Bel Power Inc., a subsidiary of Bel Fuse Inc.
Revision History
Date
Version
Changes Detail
Approval
HL
2008-10-17
2009-04-16
A
B
First release
1. Change to new format; 2. Update the I/O isolation voltage, min
efficiency and output DC current limit.
HL
2010-01-14
2011-06-14
C
D
Remove”Preliminary”
Jack
Add P/N 0RQ1-T0T12A and 0RQ1-T0T12B without trim and remote
sense function.
JZ Wang
RoHS Compliance
Complies with the European Directive 2002/95/EC, calling for the elimination of lead and
other hazardous substances from electronic products.
2011 Bel Fuse Inc. Specifications subject to change without notice. 061411
11
CORPORATE
FAR EAST
EUROPE
Bel Fuse Inc.
Bel Fuse Ltd.
Bel Fuse Europe Ltd.
206 Van Vorst Street
Jersey City, NJ 07302
Tel 201-432-0463
Fax 201-432-9542
www.belfuse.com
8F/ 8 Luk Hop Street
San Po Kong
Kowloon, Hong Kong
Tel 852-2328-5515
Fax 852-2352-3706
www.belfuse.com
Preston Technology Management Centre
Marsh Lane, Suite G7, Preston
Lancashire, PR1 8UD, U.K.
Tel 44-1772-556601
Fax 44-1772-888366
www.belfuse.com
相关型号:
0RQB-C0U
ISOLATED DC/DC CONVERTERS 48 V Input 12 V/8.3 A, 5 V/20 A, 3.3 V/25 A, 1.2-2.5 V/30 A Outputs
BEL
0RQB-C0U025
ISOLATED DC/DC CONVERTERS 48 V Input 12 V/8.3 A, 5 V/20 A, 3.3 V/25 A, 1.2-2.5 V/30 A Outputs
BEL
0RQB-C0U025G
DC-DC Regulated Power Supply Module, 1 Output, 75W, Hybrid, ROHS COMPLIANT, QUARTER BRICK PAKAGE-8
BEL
0RQB-C0U02L
ISOLATED DC/DC CONVERTERS 48 V Input 12 V/8.3 A, 5 V/20 A, 3.3 V/25 A, 1.2-2.5 V/30 A Outputs
BEL
0RQB-C0U02LG
DC-DC Regulated Power Supply Module, 1 Output, 75W, Hybrid, ROHS COMPLIANT, QUARTER BRICK PAKAGE-8
BEL
0RQB-C0U033
ISOLATED DC/DC CONVERTERS 48 V Input 12 V/8.3 A, 5 V/20 A, 3.3 V/25 A, 1.2-2.5 V/30 A Outputs
BEL
0RQB-C0U033G
DC-DC Regulated Power Supply Module, 1 Output, 82.5W, Hybrid, ROHS COMPLIANT, QUARTER BRICK PAKAGE-8
BEL
0RQB-C0U03L
ISOLATED DC/DC CONVERTERS 48 V Input 12 V/8.3 A, 5 V/20 A, 3.3 V/25 A, 1.2-2.5 V/30 A Outputs
BEL
0RQB-C0U03LG
DC-DC Regulated Power Supply Module, 1 Output, 82.5W, Hybrid, ROHS COMPLIANT, QUARTER BRICK PAKAGE-8
BEL
©2020 ICPDF网 联系我们和版权申明