VTBN6BLQ [BANNER]

VTB Pick-to-Light Optical Touch Button;


型号：	VTBN6BLQ
厂家：	Banner Engineering
描述：	VTB Pick-to-Light Optical Touch Button
文件：	总7页 (文件大小：440K)
中文：	中文翻译
下载：	下载PDF数据表文档文件

VTB Pick-to-Light Optical Touch Button

Datasheet

Ergonomic optical touch button for pick-to-light applications

•

Microcontroller-based photoelectric touch buttons

A cost-effective and easy-to-install alternative to capacitive touch switches and

mechanical push buttons for errorproofing and parts-verification applications

•

Ergonomically designed to eliminate hand, wrist, and arm stresses associated

with repeated switch operation; requires no physical pressure to operate

Illuminated base provides a bright, easy-to-see job light in one or two colors,

depending on model

•

LED power and output indicators

NPN or PNP output, depending on model

Immune to ambient light, EMI and RFI interference

High excess gain cuts through heavy airborne contamination to function in almost

any environment; optional protective field cover available

•

12 to 30 V dc operation

One-Color Job Light Models

Job Light Color

Red

Cable*

Upper Housing

Polysulfone

Output Type

Job Light Input

Green

Blue

VTBN6

VTBN6R

VTBN6B

VTBN6BQ

VTBN6BL

VTBN6BLQ

VTBP6B

2 m 4-wire cable

4-pin Euro QD

2 m 4-wire cable

4-pin Euro QD

2 m 4-wire cable

4-pin Euro QD

2 m 4-wire cable

4-pin Euro QD

VTBN6Q

VTBN6L

VTBN6LQ

VTBP6

VTBN6RQ

VTBN6RL

VTBN6RLQ

VTBP6R

NPN

0 V dc

Polycarbonate

Polysulfone

VTBP6Q

VTBP6L

VTBP6LQ

VTBP6RQ

VTBP6RL

VTBP6RLQ

VTBP6BQ

VTBP6BL

VTBP6BLQ

PNP

+4 to 30 V dc

Polycarbonate

Two-Color Job Light Models

Green and Red (see Wiring)

VTBN6GR

Cable*

Upper Housing

Output Type

Job Light Input

2 m 5-wire cable

5-pin Euro QD

2 m 5-wire cable

5-pin Euro QD

2 m 5-wire cable

5-pin Euro QD

2 m 5-wire cable

5-pin Euro QD

Polysulfone

VTBN6GRQ

NPN

0 V dc

VTBN6GRL

Polycarbonate

Polysulfone

VTBN6GRLQ

VTBP6GR

VTBP6GRQ

PNP

+4 to 30V dc

VTBP6GRL

Polycarbonate

VTBP6GRLQ

To order the 9 m (30 ft) cable models, add the suffix "W/30" to the cabled model number. (For example, VTBN6 W/30.)

Models with a quick disconnect (QD) connector require a mating cable. (See Quick Disconnect (QD) Cables on page 5).

WARNING: Not To Be Used for Personnel Protection

Never use this device as a sensing device for personnel protection. Doing so could lead to

serious injury or death. This device does not include the self-checking redundant circuitry necessary

to allow its use in personnel safety applications. A sensor failure or malfunction can cause either an

energized or de-energized sensor output condition.

Original Document

67570 Rev. E

16 May 2016

67570

VTB Pick-to-Light Optical Touch Button

Overview

Banner VTB Series touch buttons are ergonomically designed to eliminate the hand, wrist, and arm stresses associated

with mechanical push buttons. They require no physical pressure to operate. LED indicators light when power is on and

outputs are activated.

The solid-state output interfaces to a system controller, which is pre-programmed for a specific sequence of tasks.

Mounted in or near each bin in an assembler’s work station, the sensor job light signals the assembler which bins contain

items to be picked in a given operation and in what order they should be picked.

As the assembler takes a part in sequence, then reaches a finger into the yoke of the corresponding Touch Button, the

sensor senses that the part was removed and it sends an output signal to the controller. The controller then verifies if the

correct part was taken and may respond by turning that job light OFF, activating the job light of the next bin in the

sequence.

If multiple parts are to be removed from one bin, the job light may remain ON until the appropriate number of signals is

returned to the controller. If an incorrect part is selected, the control system may be wired to signal an alarm for the

assembler and/or a supervisor, or it may be programmed to interpret the action as a call for parts.

All models are immune to EMI, RFI, and ambient light interference. VTBs have either a black polysulfone or red

polycarbonate upper housing (depending on model) and a translucent white polycarbonate base. Environmental

considerations for use of the two upper housing types differ; see specifications. The entire base section lights to provide a

bright job light where a task is to be performed. The 30 mm threaded base on all models provides easy mounting.

Indicators

Output

Conducting

LED

Power ON/OFF (red):

Steady ON when power is applied

Output Conducting (red):

Switch

"Touch Area"

Steady ON when button is activated

OFF when button is not activated

Job Light:

Steady ON or flashing* when a task is to be

performed

Power ON/OFF

LED

* Flashing job light is dependent on wiring. Color is

dependent on model and wiring.

Black Polysulfone

or Red Polycarbonate

Translucent White

Polycarbonate

Base/Job Light

Installation

Consider ergonomic principles to avoid unnecessary fatigue in the installation of the hand controls. Install the touch

buttons at a height and in a location that will be comfortable for the user.

The following figure shows two methods for mounting the touch buttons, to prevent accidental switch actuation. When

mounting them on top of the control bar, the protective field covers should be in place, as shown; or for added protection,

mount the touch buttons sideways under and/or behind a protective hood, rather than on top of the bar, without using the

field covers. This side mount prevents an object from being left in the path of the beam. In addition, shields, covers, rings,

collars, dividers, or similar protection may be used to prevent accidental switch actuation.

www.bannerengineering.com - Tel: +1-763-544-3164

P/N 67570 Rev. E

VTB Pick-to-Light Optical Touch Button

Figure 1. Protect VTB touch buttons to prevent defeat or inadvertent actuation

CAUTION: Install Hand Controls to Prevent Accidental Actuation

Total protection for the two-hand control system from defeat is not possible. However, the user is

required by U.S. and International standards to arrange and protect hand controls to

minimize the possibility of defeat or accidental actuation.

CAUTION: Hand Controls

The environment in which hand controls are installed must not adversely affect the means of

actuation. Severe contamination or other environmental influences may cause slow response or false

On conditions of mechanical or ergonomic buttons. This may result in exposure to a hazard.

Wiring

Single-color models may be wired for either a solid or flashing job light. The wiring of two-color models determines the job

light. Color flashing job light is not available. Cabled model wiring shown. Cabled and QD model wiring is functionally

identical.

•

For solid color, use the standard wiring diagram.

For flashing (2 Hz), use the alternate wiring diagrams.

One-Color Job Light, NPN

(Sinking) Output Models

One-Color Job Light, PNP

(Sourcing) Output Models

Two-Color Job Light Models

NPN (Sinking) Output Models

Solid Job Light

12-30V dc

12-30 V dc

Load

Green Job Light Enable — 0V dc

Red Job Light Enable — 0V dc

Load

Job Light Enable

+4-30 V dc

Job Light Enable

0V dc

Flashing Job Light

PNP (Sourcing) Output Models

12-30 V dc

12-30V dc

12-30 V dc

Load

Green Job Light Enable — +4-30 V dc

Red Job Light Enable — +4-30 V dc

Load

Job Light Enable

0V dc

Job Light Enable

+4-30 V dc

P/N 67570 Rev. E

www.bannerengineering.com - Tel: +1-763-544-3164

VTB Pick-to-Light Optical Touch Button

Specifications

Supply Voltage and Current

Indicators

2 green LED indicators: Power ON and Output Conducting

One-color job light models: Less than 120 mA max current at 12 V dc

and less than 70 mA max current at 30 V dc (exclusive of load)

Two-color job light models: Less than 67 mA max current at 12 V dc;

less than 40 mA max current at 24 V dc; and less than 35 mA max

current at 30 V dc (exclusive of load)

Base lights green, red or blue (depending on model and wiring) as a

job light when input line is enabled. One-color models may be wired for

flashing, rather than solid color operation.

Connections

Supply Protection Circuitry

PVC-jacketed 2 m (6.5 ft) cables or 4-pin M12/Euro-style QD fitting,

depending on model; integral 9 m (30 ft) cables are also available.

Accessory QD cables required for QD models.

Protected against reverse polarity and transient voltages (fast-transient

and overvoltage)

Output Configuration

Ambient Light Immunity

1 current sinking (NPN) open collector transistor or 1 current sourcing

(PNP) open collector transistor, depending on model

Up to 120,000 lux (direct sunlight)

EMI/RFI Immunity

Output Rating

Immune to EMI and RFI noise sources, per IEC 947-5-2

Max. load: 150 mA

On-state saturation voltage: < 1.5 V at 150 mA

Off-state leakage current: < 10 μA

Construction

Totally encapsulated, non-metallic enclosure. Black polysulfone or red

polycarbonate upper housing (see Application Note below); translucent

white polycarbonate base. Electronics fully epoxy-encapsulated.

Output Protection Circuitry

All models protected against false pulse on power-up (outputs held OFF

for 1 second at power-up), overload and short-circuits.

Output Response Time

100 milliseconds ON/OFF

Operating Conditions

−20 °C to +50 °C (−4 °F to +122 °F)

90% at +55 °C maximum relative humidity (non-condensing)

Required Overcurrent Protection

WARNING: Electrical connections must be

made by qualified personnel in accordance

with local and national electrical codes and

regulations.

Environmental Rating

Meets NEMA standards 1, 3, 4, 4X, 12, and 13; IEC IP66

Application Notes

Environmental considerations for models with polysulfone upper

housings: The polysulfone upper housing will become brittle with

prolonged exposure to outdoor sunlight. Window glass effectively filters

longer wavelength ultraviolet light and provides excellent protection

from sunlight. Avoid contact with strong alkalis. Clean periodically

using mild soap solution and a soft cloth.

Environmental considerations for models with polycarbonate upper

housings: Avoid prolonged exposure to hot water and moist high

temperature environments above 66° C (150° F). Avoid contact with

aromatic hydrocarbons (such as xylene and toluene), halogenated

hydrocarbons and strong alkalis. Clean periodically using mild soap

solution and a soft cloth.

Overcurrent protection is required to be provided by end product

application per the supplied table.

Overcurrent protection may be provided with external fusing or via

Current Limiting, Class 2 Power Supply.

Supply wiring leads < 24 AWG shall not be spliced.

For additional product support, go to http://

www.bannerengineering.com.

Supply Wiring

Required Overcurrent Protection

5.0 Amps

3.0 Amps

2.0 Amps

1.0 Amps

0.8 Amps

0.5 Amps

Certifications

www.bannerengineering.com - Tel: +1-763-544-3164

P/N 67570 Rev. E

VTB Pick-to-Light Optical Touch Button

Dimensions

43.2 mm

[1.70"]

59.9 mm

[2.36"]

27.9 mm

[1.10"]

35.0 mm

[1.38"]

VTBP6

22.1 mm

[0.87"]

22.1 mm

[0.87"]

15.2 mm

[0.60"]

NPSM

Internal Threads

M30 External Threads

Jam Nut, Lock Ring, and

Seal Washers are Supplied

max. torque 4.5 N·m [40 lbf·in]

Accessories

Quick Disconnect (QD) Cables

Use the 4-pin Euro-style cordsets with the one-color job light models.

4-Pin Threaded M12/Euro-Style Cordsets

Model

Length

Style

Dimensions

Pinout (Female)

MQDC-406

MQDC-415

MQDC-430

1.83 m (6 ft)

4.57 m (15 ft)

9.14 m (30 ft)

44 Typ.

Straight

M12 x 1

ø 14.5

MQDC-450

15.2 m (50 ft)

MQDC-406RA

MQDC-415RA

MQDC-430RA

1.83 m (6 ft)

4.57 m (15 ft)

9.14 m (30 ft)

32 Typ.

[1.26"]

1 = Brown

2 = White

3 = Blue

30 Typ.

[1.18"]

Right-Angle

4 = Black

MQDC-450RA

15.2 m (50 ft)

M12 x 1

ø 14.5 [0.57"]

Use the 5-pin Euro-style cordsets with the two-color job light models.

P/N 67570 Rev. E

www.bannerengineering.com - Tel: +1-763-544-3164

VTB Pick-to-Light Optical Touch Button

5-Pin Threaded M12/Euro-Style Cordsets—Single Ended

Model

Length

Style

Dimensions

Pinout (Female)

MQDC1-501.5

MQDC1-506

MQDC1-515

0.50 m (1.5 ft)

1.83 m (6 ft)

4.57 m (15 ft)

44 Typ.

Straight

M12 x 1

ø 14.5

MQDC1-530

9.14 m (30 ft)

MQDC1-506RA

MQDC1-515RA

1.83 m (6 ft)

4.57 m (15 ft)

32 Typ.

[1.26"]

1 = Brown

2 = White

3 = Blue

30 Typ.

[1.18"]

Right-Angle

4 = Black

5 = Gray

MQDC1-530RA

9.14 m (30 ft)

M12 x 1

ø 14.5 [0.57"]

Brackets

SMB30A

SMB30MM

•

Right-angle bracket with

curved slot for versatile

•

12-ga. stainless steel bracket

with curved mounting slots

for versatile orientation

orientation

•

Clearance for M6 (¼ in)

hardware

•

Clearance for M6 (¼ in)

hardware

Mounting hole for 30 mm

sensor

Mounting hole for 30 mm

sensor

12-ga. stainless steel

Hole center spacing: A = 51, A to B = 25.4

Hole size: A = 42.6 x 7, B = ø 6.4, C = ø 30.1

Hole center spacing: A to B=40

Hole size: A=ø 6.3, B= 27.1 x 6.3, C=ø 30.5

SMBAMS30P

SMBAMS30RA

•

Flat SMBAMS series bracket

•

Right-angle SMBAMS series

bracket

30 mm hole for mounting

sensors

30 mm hole for mounting

sensors

•

Articulation slots for 90°+

rotation

Articulation slots for 90°+

rotation

12-ga. 300 series stainless

steel

12-ga. (2.6 mm) cold-rolled

steel

Hole center spacing: A=26.0, A to B=13.0

Hole size: A=26.8 x 7.0, B=ø 6.5, C=ø 31.0

Hole center spacing: A=26.0, A to B=13.0

Hole size: A=26.8 x 7.0, B=ø 6.5, C=ø 31.0

www.bannerengineering.com - Tel: +1-763-544-3164

P/N 67570 Rev. E

VTB Pick-to-Light Optical Touch Button

SMB30SC

SMB30FA

•

Swivel bracket with 30 mm

•

Swivel bracket with tilt and

83.2

mounting hole for sensor

pan movement for precise

adjustment

Black reinforced

thermoplastic polyester

•

Mounting hole for 30 mm

sensor

Stainless steel mounting and

swivel locking hardware

included

68.9

36.3

•

12-ga. 304 stainless steel

Easy sensor mounting to

extrude rail T-slot

Hole center spacing: A=ø 50.8

Hole size: A=ø 7.0, B=ø 30.0

•

Metric and inch size bolt

available

Bolt thread: SMB30FA, A= 3/8 - 16 x 2 in; SMB30FAM10, A= M10 -

1.5 x 50

Hole size: B= ø 30.1

Field Covers

Field covers are designed to prevent inadvertent activation of optical touch buttons by objects that accidentally block the

sensing beam. Field covers are constructed of rugged polypropylene and are highly resistant to abrasion and to damage by

most chemicals. A variety of colors is available, allowing color-coding when multiple touch buttons are used. Note that

when a field cover is used, it also blocks a portion of the job light.

Model

Description

Black cover

Green cover

Red cover

OTC-1-BK

OTC-1-GN

OTC-1-RD

OTC-1-YW

OTC Series

Field Cover

74.0 mm

(2.9")

Yellow cover

51.0 mm

(2.0")

69.0 mm

(2.7")

Banner Engineering Corp Limited Warranty

Banner Engineering Corp. warrants its products to be free from defects in material and workmanship for one year following

the date of shipment. Banner Engineering Corp. will repair or replace, free of charge, any product of its manufacture

which, at the time it is returned to the factory, is found to have been defective during the warranty period. This warranty

does not cover damage or liability for misuse, abuse, or the improper application or installation of the Banner product.

THIS LIMITED WARRANTY IS EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES WHETHER EXPRESS OR

IMPLIED (INCLUDING, WITHOUT LIMITATION, ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A

PARTICULAR PURPOSE), AND WHETHER ARISING UNDER COURSE OF PERFORMANCE, COURSE OF DEALING OR

TRADE USAGE.

This Warranty is exclusive and limited to repair or, at the discretion of Banner Engineering Corp., replacement. IN NO

EVENT SHALL BANNER ENGINEERING CORP. BE LIABLE TO BUYER OR ANY OTHER PERSON OR ENTITY FOR

ANY EXTRA COSTS, EXPENSES, LOSSES, LOSS OF PROFITS, OR ANY INCIDENTAL, CONSEQUENTIAL OR

SPECIAL DAMAGES RESULTING FROM ANY PRODUCT DEFECT OR FROM THE USE OR INABILITY TO USE THE

PRODUCT, WHETHER ARISING IN CONTRACT OR WARRANTY, STATUTE, TORT, STRICT LIABILITY,

NEGLIGENCE, OR OTHERWISE.

Banner Engineering Corp. reserves the right to change, modify or improve the design of the product without assuming any

obligations or liabilities relating to any product previously manufactured by Banner Engineering Corp.

www.bannerengineering.com - Tel: +1-763-544-3164

VTBN6BLQ [BANNER]

相关型号：

VTBN6BQ

VTBN6GR

VTBN6GRL

VTBN6GRLQ

VTBN6GRQ

VTBN6L

VTBN6LQ

VTBN6Q

VTBN6R

VTBN6RL

VTBN6RLQ

VTBN6RQ