SMB30Q [BANNER]
Q45BB6LL Laser Diode Retroreflective Sensors;型号: | SMB30Q |
厂家: | Banner Engineering |
描述: | Q45BB6LL Laser Diode Retroreflective Sensors |
文件: | 总8页 (文件大小:2479K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
Q45BB6LL Laser Diode Retroreflective
Sensors
Datasheet
Very-Long-Range Retroreflective Sensors for 10 V to 30 V dc
•
High power and small effective beam for retroreflective sensing
applications
•
•
Class II laser diode light source; operates from 10 V to 30 V dc
40 m (130 ft) range for polarized models and 70 m (225 ft) range for
non-polarized models, using supplied BRT-2x2 target
•
Bipolar NPN (sinking) and PNP (sourcing) solid-state outputs,
switchable light and dark operate; 250 mA maximum load
Top mounted Power, Signal (AID System), and Output indicator LEDs
Optional plug-in Pulse or Delay timing logic and display modules
Designed to withstand 1200 psi washdown; exceeds its NEMA 6P and
IEC IP67 rating
™
•
•
•
U.S. Patent(s) issued or pending
WARNING: Not To Be Used for Personnel Protection
Never use this device as a sensing device for personnel protection. Doing so could lead to
serious injury or death. This device does not include the self-checking redundant circuitry necessary
to allow its use in personnel safety applications. A sensor failure or malfunction can cause either an
energized or de-energized sensor output condition.
Models
Non-Polarized Models
Model
Cable1
Range
Beam Color
Sensing Mode
Q45BB6LL
5-wire 2 m (6.5 ft)
5-Pin Mini-style QD
5-Pin Euro-style QD
0.3 to 70 m (1 ft to 225
ft) w/BRT-2x2
Q45BB6LLQ
Q45BB6LLQ6
Visible red, 655 nm
(included)
RETRO
Polarized Models
Model
Cable1
5-wire 2 m (6.5 ft)
5-Pin Mini-style QD
5-Pin Euro-style QD
Range
Beam Color
Sensing Mode
Q45BB6LLP
Q45BB6LLPQ
Q45BB6LLPQ6
0.6 to 40 m (2 ft to 130
ft) w/BRT-2x2
P
Visible red, 655 nm
(included)
POLAR RETRO
1
•
•
To order the 9 m (30 ft) cable models, add the suffix "W/30" to the cabled model number.
Models with a quick disconnect (QD) connector require a mating cable.
Original Document
38244 Rev. C
27 April 2016
38244
Q45BB6LL Laser Diode Retroreflective Sensors
Overview
Status indicator LEDs for Power, Signal and Output are clearly visible
beneath a raised dome in the sensor’s transparent o-ring-sealed
polycarbonate cover. The Power indicator lights whenever power is applied
to the sensor. The Signal LED lights whenever the sensor sees its modulated
light source, and pulses at a rate proportional to the strength of the
Sensitivity
Adjustment
™
received light signal; this is the AID Alignment Indicating Device. The
Output Status
Indicator
Signal Indicator
Output indicator lights whenever the sensor’s output is conducting. This
indicator is especially useful when a timing logic module is used and Signal
and Output conditions are not concurrent.
Power ON
Indicator
Light/Dark
Operate Switch
Also located beneath the sensor’s o-ring-sealed cover are controls for light/
dark operate selection and Sensitivity (gain) adjustment.
Optional LED
Signal Strength
Display
Optional Timing
Adjustments
CAUTION: Never stare directly into the sensor lens. Laser light can damage your eyes. Avoid
placing any mirror-like object in the beam. Never use a mirror as a retroreflective target.
CAUTION: Do Not Disassemble for Repair
This device contains no user-serviceable components. Do not attempt to disassemble for repair. Use
of controls or adjustments or performance of procedures other than those specified herein may
result in hazardous radiation exposure. A defective unit must be returned to the manufacturer.
Device Setup
Alignment
Conventional retroreflective photoelectric sensors are extremely easy to align. Beam angles are wide, and retro targets are
forgiving to angle of incidence of the light beam. The beam of the Q45 laser sensor is very narrow, compared with the
beam of most retro sensors. As Table 1 on page 2 indicates, the effect of angular misalignment can be dramatic.
Alignment is critical because the beam may miss the retroreflective target unless the retro target is large.
For example, with one BRT-2x2 mounted at a distance of 6 m (20 ft) from the sensor, one degree of angular misalignment
will cause the center of the laser beam to miss the center of the target by 4 inches (i.e., the beam will miss the edge of
the reflector by almost 3 inches).
Table 1: Beam Displacement per Degree of Misalignment
Sensor-to-Target Distance (X)
1.5 m (5 feet)
Beam Displacement (Y) for 1
25 mm (1 inches)
Ø = Misalignment Angle
C
L
3 m (10 feet)
50 mm (2 inches)
Y
3 m (10 feet)
100 mm (4 inches)
Sensing Distance = X
Y = X(tan Ø)
15 m (50 feet)
250 mm (10 inches)
500 mm (20 inches)
750 mm (30 inches)
1000 mm (40 inches)
30 m (100 feet)
45 m (150 feet)
60 m (200 feet)
2
www.bannerengineering.com - Tel: +1-763-544-3164
P/N 38244 Rev. C
Q45BB6LL Laser Diode Retroreflective Sensors
Alignment Tip
When using a small retroreflective target at medium or long range, temporarily attach (or suspend) a strip of
retroreflective tape (e.g., BRT-THG-2) along a line which intersects the actual target. The visible red laser beam is easily
seen in normal room lighting. Sight along the beam toward the target (from behind the sensor). Move the sensor to scan
the laser beam back and forth across the retro tape strip. Use the tape strip to guide the beam onto the target.
Consider the use of Banner sensor mounting bracket SMB30SC. This swivel bracket can simplify multiple-axis alignment.
Alignment is complete when the visible image is centered on the retro target. The perpendicularity of the laser beam to the
face of the retro target is forgiving, just as it is with a conventional retroreflective sensor.
Effective Beam Size
Unlike conventional retroreflective sensors, the retroreflective laser has the ability to sense relatively small profiles. Table
2 on page 3 indicates the diameter of the smallest opaque rod which will reliably break the laser beam at several
sensor-to-object distances. These figures assume an excess gain of about 10 times. Flooding effects are possible when the
gain is much higher. This means that sensor gain may have to be reduced in some situations in order to reliably detect
these minimum object sizes.
Note that the shape of the beam is elliptical. The minimum object sizes listed assume passage of the rod across the major
diameter of the ellipse (worst case). It may be possible to detect objects smaller than the sizes listed if the direction in
which the objects pass through the beam can be controlled.
Table 2: Minimum Object Detection Size vs. Distance from Sensor
Distance from Sensor to Object
0.3 m (1 feet)
Minimum Object Detection Size
2.5 mm (0.10 inches)
3.0 mm (0.12 inches)
4.5 mm (0.18 inches)
19 mm (0.75 inches)
1.5 m (5 feet)
3 m (10 feet)
15 m (50 feet)
30 m (100 feet)
25 mm (1.0 inches)
Wiring Diagrams
Cabled Models
Mini- or Euro-Style Quick-Disconnect Models
bn
bn
bu
wh
bk
ye
+
+
10-30V dc
–
10-30V dc
–
bu
wh
Load
Load
Load
bk
Load
ye or gy
Beam Inhibit: Connect to +V
Beam Inhibit: Connect to +V
P/N 38244 Rev. C
www.bannerengineering.com - Tel: +1-763-544-3164
3
Q45BB6LL Laser Diode Retroreflective Sensors
Specifications
Supply Voltage and Current
Adjustments
10 V to 30 V dc (10% maximum ripple), at less than 50 mA (exclusive
of load)
Beneath sensor’s transparent cover: Light/Dark Operate select
switch and multi-turn Sensitivity control on top of sensor allow precise
sensitivity setting (turn clockwise to increase gain). Optional logic and
logic/display modules have adjustable timing functions.
Supply Protection Circuitry
Protected against reverse polarity and transient voltages
Construction
Output Configuration
Molded thermoplastic polyester housing, o-ring sealed transparent
polycarbonate top cover, molded acrylic lenses, and stainless steel
hardware. Q45 sensors are designed to withstand 1200 psi washdown.
The base of cabled models has a 1/2" NPS integral internal conduit
thread.
Bipolar: one current sourcing (PNP) and one current sinking (NPN)
open-collector transistor
Output Rating
250 mA maximum each output up to 50° C, derated to 150 mA at 70°
C (derate 5 mA/°C)
Off-state leakage current: less than 1 microamp
Output saturation voltage (both outputs): less than 1 volt at 10
mA and less than 2 volts at 250 mA
Environmental Rating
NEMA 6P, IEC IP67
Laser Classification
Class II laser product. US Safety Standards 21 CFR 1040.10 and
1040.11; European Standards EN 60825 and IEC 60825
Output Protection Circuitry
Protected against false pulse on power-up and continuous overload or
short circuit of outputs
Connections
PVC-jacketed 2 m (6.5 ft) or 9 m (30 ft) cables, or 5-pin Mini-style (“Q”
suffix models) or 5-pin Euro-style (“Q6”suffix models) quick disconnect
(QD) fitting are available. QD cables are ordered separately.
Output Response Time
Less than 2 milliseconds
1 second delay on power-up; outputs do not conduct during this time.
Operating Conditions
Repeatability
–10° to +40° C (+14° to 104° F)
90% at +50 °C maximum relative humidity (non-condensing)
0.5 milliseconds; response time and repeatability specifications are
independent of signal strength
Application Notes
Indicators
Optional logic timing modules are available
Indicator LEDs are visible beneath a raised transparent polycarbonate
dome on top of the sensor.
Certifications
Power (green) LED: lights whenever 10 V to 30 V dc power is
applied, and flashes to indicate output overload or output short circuit.
A steady green LED also indicates that laser light is being emitted.
™
Signal (red) AID system LED: lights whenever the sensor sees its
modulated light source, and pulses at a rate proportional to the
strength of the received light signal
Load (amber) LED: lights whenever an output is conducting
Optional 7-element LED: signal strength display module
4
www.bannerengineering.com - Tel: +1-763-544-3164
P/N 38244 Rev. C
Q45BB6LL Laser Diode Retroreflective Sensors
Dimensions
Cabled Models
5-Pin Mini-Style Quick-
Disconnect Models
5-Pin Euro-Style Quick-
Disconnect Models
Transparent Cover (Gasketed)
View: Sensing Status
Output Load Status
Power
Open to Access:
Sensitivity (Gain) Adjustment
Timing Adjustments
Light/Dark Operate Switch
54.1 mm
Emitter Axis
28.6 mm (1.13")
(2.13")
44.5 mm
(1.75")
Lens Centerline
50.8 mm
(2.00")
69.0 mm
(2.72")
6.4 mm (0.25")
87.6 mm
(3.45")
4.5 mm (#10) Screw
Clearance (2)
7.1 mm
(0.28")
30.0 mm
(1.18")
External Thread
M30 X 1.5
Euro-style
QD Connector
14 mm (0.6")
15 mm (0.6")
Internal Thread
Mini-style QD Connector
ø 6.1 (0.24")
(1/2–14NPSM)
2m (6.5') Cable
External Thread
M30 X 1.5
Excess Gain Curves
Non-Polarized Models
Polarized Models
1000
100
10
1000
100
10
Q45BB6LLP (Q)
Q45BB6LL (Q)
Retroreflective
Mode
E
X
C
E
S
S
E
X
C
E
S
S
Polarized
Retroreflective
Mode
BRT 2 x 2
Reflector
BRT 2 x 2
Reflector
BRT-THG
Tape
G
A
I
G
A
I
BRT-THG
Tape
N
N
1
1
0.1 m
0.3'
1 m
3.3'
10 m
33'
100 m
333'
0.1 m
0.3'
1 m
3.3'
10 m
33'
100 m
333'
DISTANCE
DISTANCE
P/N 38244 Rev. C
www.bannerengineering.com - Tel: +1-763-544-3164
5
Q45BB6LL Laser Diode Retroreflective Sensors
Accessories
Quick-Disconnect (QD) Cables
5-Pin Threaded M12/Euro-Style Cordsets—Single Ended
Model
Length
Style
Dimensions
Pinout (Female)
MQDC1-501.5
MQDC1-506
MQDC1-515
0.50 m (1.5 ft)
1.83 m (6 ft)
4.57 m (15 ft)
2
1
4
44 Typ.
3
5
Straight
1 = Brown
M12 x 1
2 = White
3 = Blue
4 = Black
5 = Gray
MQDC1-530
9.14 m (30 ft)
ø 14.5
5-Pin Mini-Style Cordsets
Model
Length
Style
Dimensions
Pinout (Female)
MBCC-506
1.83 m (6 ft)
3.66 m (12 ft)
1
2
5
MBCC-512
52 Typ.
7/8-16UN-2B
ø 25.5
4
3
Straight
1 = Black
2 = Blue
MBCC-530
9.14 m (30 ft)
3 = Yellow
4 = Brown
5 = White
Retroreflective Targets
Banner offers a wide selection of high-quality retroreflective targets.
See the Accessories section of your current Banner Photoelectric
Sensors catalog for complete information.
NOTE: Polarized sensors require corner cube type
retroreflective targets only. Non-polarized sensors
may use any retroreflective target.
Output Timing Logic and Signal Strength Display Modules
Q45 sensors easily accept the addition of output timing logic and signal strength display functions. Display modules have a
™
seven-element display that gives a more precise indication of excess gain than does the AID system LED that is standard
on Q45 sensors. The modules listed below may be used with all Q45BB6LL sensors. Refer to the module's datasheet for
more information.
Models
45LM58
45LM58D
45LMD
Logic and/or Display Function
Programmable output timing logic
Programmable output timing logic plus signal strength display
Signal strength display only (no timing function)
6
www.bannerengineering.com - Tel: +1-763-544-3164
P/N 38244 Rev. C
Q45BB6LL Laser Diode Retroreflective Sensors
Mounting Brackets
SMB30A
45
SMB30UR
•
Right-angle bracket with
curved slot for versatile
orientation
•
2-piece universal swivel
bracket for limit-switch style
sensors
C
61
•
•
•
Clearance for M6 (¼ in)
hardware
Mounting hole for 30 mm
sensor
•
•
300 series stainless steel
Stainless steel swivel locking
hardware included
B
A
69
Hole center spacing: A to B=31.8, B to C=19.0, A to C=50.8, D=50.8
Hole size: C=6.9x32, D=73.0x6.9
12-ga. stainless steel
Hole center spacing: A to B=40
Hole size: A=ø 6.3, B= 27.1 x 6.3, C=ø 30.5
45
SMB30MM
SMBAMS30P
57
70
•
12-ga. stainless steel bracket
with curved mounting slots
for versatile orientation
•
•
Flat SMBAMS series bracket
30 mm hole for mounting
sensors
C
C
A
93
57
•
•
Clearance for M6 (¼ in)
hardware
Mounting hole for 30 mm
sensor
•
•
Articulation slots for 90°+
rotation
12-ga. 300 series stainless
steel
B
B
A
Hole center spacing: A = 51, A to B = 25.4
Hole size: A = 42.6 x 7, B = ø 6.4, C = ø 30.1
Hole center spacing: A=26.0, A to B=13.0
Hole size: A=26.8 x 7.0, B=ø 6.5, C=ø 31.0
SMB30Q
SMBAMS30RA
45
•
Right-angle flanged
mounting bracket with
curved slot for versatile
orientation
12-ga. stainless steel
Mounting hole for 30 mm
sensor
•
•
•
•
Right-angle SMBAMS series
bracket
30 mm hole for mounting
sensors
Articulation slots for 90°+
rotation
12-ga. (2.6 mm) cold-rolled
steel
C
53
A
B
•
•
48
Hole center spacing: A to B=40
Hole size: A=ø 6.3, B=ø 27.1 x 6.3, C=ø 30.7
Hole center spacing: A=26.0, A to B=13.0
Hole size: A=26.8 x 7.0, B=ø 6.5, C=ø 31.0
67
SMB30SC
•
•
•
Swivel bracket with 30 mm
mounting hole for sensor
Black reinforced
B
58
thermoplastic polyester
Stainless steel mounting and
swivel locking hardware
included
29
A
Hole center spacing: A=ø 50.8
Hole size: A=ø 7.0, B=ø 30.0
P/N 38244 Rev. C
www.bannerengineering.com - Tel: +1-763-544-3164
7
Q45BB6LL Laser Diode Retroreflective Sensors
Banner Engineering Corp. Limited Warranty
Banner Engineering Corp. warrants its products to be free from defects in material and workmanship for one year following the date of shipment. Banner Engineering Corp.
will repair or replace, free of charge, any product of its manufacture which, at the time it is returned to the factory, is found to have been defective during the warranty
period. This warranty does not cover damage or liability for misuse, abuse, or the improper application or installation of the Banner product.
THIS LIMITED WARRANTY IS EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES WHETHER EXPRESS OR IMPLIED (INCLUDING, WITHOUT LIMITATION,
ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE), AND WHETHER ARISING UNDER COURSE OF PERFORMANCE, COURSE
OF DEALING OR TRADE USAGE.
This Warranty is exclusive and limited to repair or, at the discretion of Banner Engineering Corp., replacement. IN NO EVENT SHALL BANNER ENGINEERING CORP. BE
LIABLE TO BUYER OR ANY OTHER PERSON OR ENTITY FOR ANY EXTRA COSTS, EXPENSES, LOSSES, LOSS OF PROFITS, OR ANY INCIDENTAL,
CONSEQUENTIAL OR SPECIAL DAMAGES RESULTING FROM ANY PRODUCT DEFECT OR FROM THE USE OR INABILITY TO USE THE PRODUCT, WHETHER
ARISING IN CONTRACT OR WARRANTY, STATUTE, TORT, STRICT LIABILITY, NEGLIGENCE, OR OTHERWISE.
Banner Engineering Corp. reserves the right to change, modify or improve the design of the product without assuming any obligations or liabilities relating to any product
previously manufactured by Banner Engineering Corp.
Copyright Notice
Any misuse, abuse, or improper application or installation of this product or use of the product for personal protection applications when the product is identified as not
intended for such purposes will void the product warranty. Any modifications to this product without prior express approval by Banner Engineering Corp will void the product
warranties. All specifications published in this document are subject to change; Banner reserves the right to modify product specifications or update documentation at any
©
time. For the most recent version of any documentation, refer to: www.bannerengineering.com.
Banner Engineering Corp. All rights reserved.
www.bannerengineering.com - Tel: +1-763-544-3164
相关型号:
©2020 ICPDF网 联系我们和版权申明